| Age | Commit message (Collapse) | Author |
|---|
|
Add the register PNP_IO4, which will be used by IT5570E in CB:48894.
Change-Id: Ic820295247323f546d4c48ed17cfa4eab3dc5e92
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48924
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Introduce a new device `gpio` that is going to be used for generic
abstraction of gpio operations in the devicetree.
The general idea behind this is that every chip can have gpios that
shall be accessible in a very generic way by any driver through the
devicetree.
The chip that implements the chip-specific gpio operations has to assign
them to the generic device operations struct, which then gets assigned
to the gpio device during device probing. See CB:48583 for how this gets
done for the SoCs using intelblocks/gpio.
The gpio device then can be added to the devicetree with an alias name
like in the following example:
chip soc/whateverlake
device gpio 0 alias soc_gpio on end
...
end
Any driver that requires access to this gpio device needs to have a
device pointer (or multiple) and an option for specifying the gpio to be
used in its chip config like this:
struct drivers_ipmi_config {
...
DEVTREE_CONST struct device *gpio_dev;
u16 post_complete_gpio;
...
};
The device `soc_gpio` can then be linked to the chip driver's `gpio_dev`
above by using the syntax `use ... as ...`, which was introduced in
commit 8e1ea52:
chip drivers/ipmi
use soc_gpio as gpio_dev
register "bmc_jumper_gpio" = "GPP_D22"
...
end
The IPMI driver can then use the generic gpio operations without any
knowlege of the chip's specifics:
unsigned int gpio_val;
const struct gpio_operations *gpio_ops;
gpio_ops = dev_get_gpio_ops(conf->gpio_dev);
gpio_val = gpio_ops->get(conf->bmc_jumper_gpio);
For a full example have a look at CB:48096 and CB:48095.
This change adds the new device type to sconfig and adds generic gpio
operations to the `device_operations` struct. Also, a helper for getting
the gpio operations from a device after checking them for NULL pointers
gets added.
Successfully tested on Supermicro X11SSM-F with CB:48097, X11SSH-TF with
CB:48711 and OCP DeltaLake with CB:48672.
Change-Id: Ic4572ad8b37bd1afd2fb213b2c67fb8aec536786
Tested-by: Johnny Lin <Johnny_Lin@wiwynn.com>
Tested-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: Patrick Rudolph <siro@das-labor.org>
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48582
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
The register `ESR` conflicts with the `Exception syndrome register` in
UDK2017. To resolve the conflict, drop the unused `ESR` register from
gma registers. It can be readded and prefixed or renamed if it's
required at a later point.
Change-Id: Icfdd834aea59ae69639a180221f5e97170fbac15
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48758
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Change-Id: I002ade555c0544e4ef738c1ad45ee3d8aa38e03e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40720
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
We missed that Cannon Point, the PCH usually paired with Coffee, Whiskey
and Comet Lake, differs a bit from its predecessors. Hence, libgfxinit
now has a new Kconfig setting for the PCH.
Change-Id: I1c02c0d9abb7340aabe94185ee5e17ef4c2b0d36
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48764
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
All known on-chip PCI devices are documented in chipset devicetree now
and default to disabled. There is no need to keep disabled PCI devices
in the mainboard's devicetree. Thus, remove them.
Change-Id: I0f78dadd9e55a8f002394dc07ab514ca13f4e963
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48887
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Change-Id: Ide10889ad01ec6d31ee83158182876625a68a5da
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48888
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The CedarIsland FSP Integration recommends locking down some things.
Change-Id: I72e04b55d69a8da79485e084b39c3bd38504897f
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47168
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This is required for CbNT.
Change-Id: I565a95cd2e76cb1c648884be6d1954288f6e4804
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47447
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
This is required for CBnT.
Change-Id: If5637eb8dd7de406b24b92100b68c5fa11c16854
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47448
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Add rtc MT6359P driver for rtc init and rtc eosc calibration. Refactor
mt8173 and mt8183 code by extracting common API. Move rtc_read and
rtc_write to each SoC folder, because mt8173 and mt8183 access rtc via
pmic wrapper, while mt8192 accesses it via pmif.
Reference datasheet:
Document No: RH-D-2018-0101.
Signed-off-by: Yuchen Huang <yuchen.huang@mediatek.corp-partner.google.com>
Change-Id: I57d6738fdec148c7458b2024a0a8225415ca2f3e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46395
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
Add basic devapc (device access permission control) drivers.
DAPC driver is used to set up bus fabric security and data protection
among hardwares. DAPC driver groups the master hardwares into different
domains and gives secure and non-secure property. The slave hardware can
configure different access permissions for different domains via DAPC
driver.
Change-Id: I2ad47c86b88047c76854a6f8a67b251b6a9d4013
Signed-off-by: Nina Wu <nina-cm.wu@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46402
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
Before calibration, dramc resets the delay of each PHY IO, calculates
TX path and sets CKE to be rank independent.
Signed-off-by: Huayang Duan <huayang.duan@mediatek.com>
Change-Id: I071eca037f89a916d6cfaf5b008d64f2b4a269a9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44706
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
src/northbridge/amd/pi/00660F01/Kconfig does not exist. Remove the
source statement.
Also, no kconfig files under src/soc/intel/common/basecode/. Clean
that up.
Signed-off-by: Jack Rosenthal <jrosenth@chromium.org>
Change-Id: I10917b76ff6c2a9d5a97d5c7dfa9e8925cd8c8a4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48676
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Now that CHAP device is declared in chipset devicetree, hook it up to
devicetree configuration.
Change-Id: Icc51f7b9cda32d5058dce958e386921b6d3d8ffb
Signed-off-by: Benjamin Doron <benjamin.doron00@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48323
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The code in soc/amd/common has an implementation of
GPIO register space that is compatible with the hardware
sb/amd/pi/hudson supports.
Change-Id: I86ae40a3cdf335263d7e9e3dcfdd588947cdd9b1
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42733
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Add SMBIOS slot descriptions for M.2 ports and remove duplicate
comments.
Change-Id: Ieff03ad3167aec054cdc6b67ddc20fc64394e347
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48389
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Change-Id: I1c1b5710a5236fe4a3bdda1fc978393e636e9817
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45773
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Signed-off-by: Idwer Vollering <vidwer@gmail.com>
Change-Id: If77d59485451c77dcea752bc4fe0dfadba8fec45
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48900
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The Sandy Bridge steppings appear in the BWG, and Ivy Bridge steppings
appear in reference code. Add them for the sake of completeness.
Change-Id: I7d17cdd04a771ca319c908fc757f868e95ea7944
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48410
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
The steppings correspond to the CPUID bits 3:0, so move them to the CPU
scope, and include the CPU header from files using the stepping macros.
Change-Id: Idf8fba4911f98953bb909777aea57295774d8400
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48409
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Rewrite some constants to make their meaning somewhat clearer.
Tested with BUILD_TIMELESS=1, Asus P8Z77-V LX2 does not change.
Change-Id: I321f5e61d7c695ae77e61b84728e34930f69d400
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48615
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Native raminit only supports 1.5V operation, but there are DIMMs which
request 1.65V operation in XMP profiles. Add an option to force XMP to
be used when the requested voltage isn't supported, which will run the
DIMMs at 1.5V with XMP timings. Consider this to be overclocking.
Change-Id: I64bfac8f72dadf662ceadfc7998daf26edf5a710
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48614
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
We need this to happen prior to SMM module loader. If
there is some debugging output it's better they do not
appear in the middle of CPU bringup.
Change-Id: I45b4b5c0c5bf8bee258a465d1e364bfe98190e44
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48697
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Change-Id: I0d1e7b86d5b98da85bf539a4a3ec23e0eeaa4dfc
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48768
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Structure with chromeos_acpi_t is expected to have size
0x1000. Only ones with device_nvs_t have size 0x2000.
Change-Id: I2eaa3a008566853b4144fa34ccffaa232d5d8e24
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48767
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
|
|
Update galtic device tree override to match schematics.
BUG=b:170913840
BRANCH=dedede
TEST=emerge-dedede coreboot
Signed-off-by: FrankChu <frank_chu@pegatron.corp-partner.google.com>
Change-Id: I270cd2a9783030ad3a080b9cfda8a133e801c5ce
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48656
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Rename to graphics_soc_panel_init, to more accurately convey
operations performed by the function. Guard execution so we
don't attempt to reconfigure the panel after FSP has already
done so.
This fixes FSP/GOP display init on APL/GLK, which was broken by
attempting to configure the panel after FSP had already done so.
Change-Id: I8e68a16b2efb59965077735578b1cc6ffd5a58f0
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48884
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add a new driver for OEM commands and select it from x11-lga1151-series.
The driver communicates the BIOS version and date to the BMC using OEM
commands. The command should be supported on all X11 series mainboards,
but might work with older BMC, too.
Tested on X11SSH-TF:
The BIOS version strings are updated on boot and are visible in the
BMC web UI.
Change-Id: I51c22f83383affb70abb0efbcdc33ea925b5ff9f
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Signed-off-by: Christian Walter <christian.walter@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38002
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
Only one EEPROM is used to store the board settings, and its I2C address
is constant. Thus, there's no need to pass its address as a parameter.
In addition, reduce the scope of the `I2C_ADDR_EEPROM` definition, since
using it outside of eeprom.c would bypass the API's abstraction layer.
Change-Id: I958304e6ed6df05af923139d44ff4fd1de204738
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46565
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
Drop chipset register definitions in mainboard code in favor of existing
definitions in a header. These definitions are not mainboard-specific.
Tested with BUILD_TIMELESS=1, Prodrive Hermes remains identical.
Change-Id: I29d6f35ec27bff43cf52ae697e905b6a7b48a8d1
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48805
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
Change-Id: I0251d1193bb36ae73d592a0d17f580b7edaddbf6
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48853
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch add SSD D3 cold support for lindar.
BUG=b:172405687
BRANCH=firmware-volteer-13521.B
TEST=Built and booted into OS.
Signed-off-by: Kevin Chang <kevin.chang@lcfc.corp-partner.google.com>
Change-Id: Ie343bbff3bde4ff2a7e89bd384d5661af372b560
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48651
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Based on latest schematic, disable PCIe 7 and 8 for WLAN and SD card.
BUG=b:169356808
TEST=FW_NAME=voema emerge-volteer coreboot chromeos-bootimage
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: I2a4658a382c094c2a5b16b7acaf464f54e9897b1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48845
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Enable Runtime D3 for the volteer variants that have GPIO power control
of the NVMe device attached to PCIe Root Port 9.
Enable the GPIO for power control for variants that do not already have
it configured to allow the power to be disabled in D3 state.
BUG=b:169356808
TEST=tested on voema
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: I28ef074225c533e1a97b6ec4a1a5dd1dcc198168
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48848
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Isochronous operation negatively impacts memory performance, as
per Intel MLC (Memory Latency Checker) benchmark results. Thus,
disable isochronous operation, like analogous UEFI firmware does.
The MLC results after disabling isoch:
"--max_bandwidth"
ALL Reads : 106948.17
3:1 Reads-Writes : 101580.46
2:1 Reads-Writes : 100523.26
1:1 Reads-Writes : 99059.44
Stream-triad like : 97762.47
"--peak_injection_bandwidth"
ALL Reads : 105724.3
3:1 Reads-Writes : 100655.8
2:1 Reads-Writes : 99463
1:1 Reads-Writes : 98708
Stream-triad like : 91515
The MLC results before disabling isoch:
"--max_bandwidth"
ALL Reads : 88824.96
3:1 Reads-Writes : 94820.81
2:1 Reads-Writes : 94867.53
1:1 Reads-Writes : 92567.36
Stream-triad like : 91900.43
"--peak_injection_bandwidth"
ALL Reads : 88859.6
3:1 Reads-Writes : 94064
2:1 Reads-Writes : 94186.2
1:1 Reads-Writes : 92516.1
Stream-triad like : 85147.4
TEST=On OCP Delta Lake, verify that MLC benchmark results have
improved.
Change-Id: I08c22ee001b601e607452b3f23fad969ecb484b4
Signed-off-by: Johnny Lin <johnny_lin@wiwynn.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48738
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
Reviewed-by: Jonathan Zhang <jonzhang@fb.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
A new board introduced to Kukui family.
BUG=b:176206134
TEST=make # select Katsu
BRANCH=kukui
Signed-off-by: Sunway <lisunwei@huaqin.corp-partner.google.com>
Change-Id: I09fe2b8f6922dfd2af6424830568466fb98f7aee
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48874
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
Remove the unused SOC_INTEL_COMMON_ACPI Kconfig option.
Change-Id: Id62cd44e0f7e4175ae65c9388569231d5c8c1fbc
Signed-off-by: Marc Jones <marcjones@sysproconsulting.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48580
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Benjamin Doron <benjamin.doron00@gmail.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Remove the unnecessary header file includes.
Change-Id: I0d849cb236f304b87332aa64b2f10c73cad2d4dd
Signed-off-by: Marc Jones <marcjones@sysproconsulting.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48826
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Jay Talbott <JayTalbott@sysproconsulting.com>
Reviewed-by: Jonathan Zhang <jonzhang@fb.com>
|
|
Leverage existing `ch_dimms` value and use constants for brevity.
Change-Id: I4e08166c8e9fbd15ff1dcd266abb0689e4b159f7
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48613
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Pointers to structs can be very useful, especially when they point to an
array element. In this case, changing one pointer allows the function to
be rewritten more concisely, since most redundancy can be eliminated.
Tested on Asus P8Z77-V LX2, still boots. No functional difference.
Change-Id: I7f0c37ea49db640f197162f371165a6f8e9c1b9c
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48612
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Ensure that IOSAV is finished before continuing. This might solve some
random failures on the I/O and roundtrip latency training algorithm.
Tested on Asus P8Z77-V LX2, still boots.
Change-Id: Ic08a40346b6c60e372bada10f9c4ee42eb974f9f
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48403
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Most ofte, `iosav_run_once` precedes a `wait_for_iosav` call. Add a
helper function to reduce clutter. The cases where `iosav_run_once`
isn't followed by `wait_for_iosav` will be handled in a follow-up.
Tested on Asus P8Z77-V LX2, still boots.
Change-Id: Ic76f53c2db41512287f41b696a0c4df42a5e0f12
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48402
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
These comments were helpful before the massive IOSAV refactoring, but
they are no longer needed since the function names are clear enough.
Change-Id: Ieb9bdf3f7fc72f63a8978f2b98e0bc8228c55868
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48401
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Print delay values in a suitable format for human consumption.
Change-Id: I0d86187d3e458ee2cb3fd11ec896ac363b8d3249
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48400
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I164daa59696f2fe8de3a4b3e7da46c7c723778eb
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48602
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Now that the purpose of each training algorithm is clear, replace the
last instances of the original names in comments and print statements
with the current, correct names. Also, print which channel has failed
command training, for completeness and consistency with other errors.
Change-Id: I9cc5c4b04499297825ca004c6bd1648a68449d2c
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48601
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Document the algorithm to adjust I/O and roundtrip latencies.
Change-Id: Ic8b9aed54a34bb3252c457e87e81387fd410e305
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48397
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Tested on Asus P8H61-M PRO, still boots.
Change-Id: I147ba0ade8a5317a0fe76e9ea84947fd91d794b4
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47773
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Refactor in preparation to split up `program_timings`.
Tested on Asus P8Z77-V LX2, still boots.
Change-Id: I68410165f397d8b4f662e40e88fb6a58ab1c5cff
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47772
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Use absolute values for the Rx and Tx bus timings instead of values
relative to the CA (Command/Address) bus timing. This makes the
calculations more accurate, less complex and less error-prone.
Tested on Asus P8H61-M PRO, still boots. Training results do not seem to
be affected by this patch, and the margins roughly have the same shape.
Change-Id: I28ff1bdaadf1fcbca6a5e5ccdd456de683206410
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47771
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This file was being written to the root src directory. It is the only
file being written to src during a normal build, while all others are
being written to $(obj). I added a new variable to allow specifying the
xcompile path. This allows generating a single file if building multiple
boards. I also moved the default location into $(obj) so we don't
pollute the src directory by default.
I also cleaned up the generation of xcompile by removing the unnecessary
eval and NOCOMPILE check.
I also left .xcompile in distclean so it cleans up stale files.
Since .xcompile is written into $(obj), `make clean` will now remove it.
The tegra Makefiles are outside of the normal build process, so I just
updated those Makefiles to point to the default xcompile location of a
normal build. The what-jenkins-does target had to be updated to support
these special targets. We generate an xcompile specifically for these
targets and pass it into the Makefile. Ideally we should get these
targets added to the main build.
BUG=b:112267918
TEST=ran `emerge-grunt coreboot` and `make what-jenkins-does`
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: Ia83f234447b977efa824751c9674154b77d606b0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/28101
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
List of changes:
FSP-S Header:
- Add UPD MicrocodeRegionBase and MicrocodeRegionSize
- Adjust UPD Offset for Reservedxx
Change-Id: I376abf6cd64dcf8c848901074e2c2f30d4f302da
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48846
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
|
|
Port commit ba75c4c (soc/intel/tigerlake: Enable support for
extended BIOS window) for Alderlake
Change-Id: Iaa8464d45884de433cca4f6a250cdd8d4c8f3661
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48755
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Port commit 237afda (src/soc/intel/tigerlake: Add SPI DMI Destination ID)
into Alderlake.
Change-Id: Ia0b465d405ab3c70b7d4094d32c182cab30fe531
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48754
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
TEST=Able to build and boot ADLRVP.
Change-Id: I93da53f8835e0eec4cf4e78daab26332fd55d334
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48753
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Change-Id: Idd02573e6b47c3bcbdcefa7b04fb9098b600df49
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48804
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
Commit 56fcfb5 misused the PCH_DEVFNs passed to the XHCI elog driver, by
passing them directly to pci_s_read_config32. This is incorrect, as it
is the wrong PCI devfn encoding to pass to that function.
BUG=b:175996770
TEST=abuild
Change-Id: Id7c146c1f50ee64a725bd50f9f11a7f159013a2b
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48827
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sukumar Ghorai <sukumar.ghorai@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Current implementation uses CPUID 0Bh function that returns the number
of logical cores of requested level. The problem with this approach is
that this value doesn't change when HyperThreading is disabled (it's in
the Intel docs), so it breaks generate_cpu_entries() because `numcpus`
ends up being zero due to integer division truncation.
- Use MSR 0x35 instead, which returns the correct number of logical
processors with and without HT.
- Use cpu_read_topology() to gather the required information
Tested on Prodrive Hermes, the ACPI code is now generated even with
HyperThreading disabled.
Change-Id: Id9b985a07cd3f99a823622f766c80ff240ac1188
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48691
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Following up 3ccae2b7, this patch adds Iccmax and AC/DC
loadlines and iPL2 for CML-S CPUs. The information is from
CML EDS volume 1, doc #606599 and pdg #610244.
Change-Id: Id2797a979a8b6a52a34baae66f95c7136ed1dc72
Signed-off-by: Gaggery Tsai <gaggery.tsai@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38288
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
According to doc# IHD-OS-BXT-Vol 2b-05.17 the cycle delay is in the bit
range 8:4 of register PP_CONTROL. The current code writes the value to
bits 4:0, though. Correct that by shifting the value left by 4 bits.
Change-Id: If407932c847da39b19e307368c9e52ba1c93bccd
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48759
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
The CHROMEOS option was never used with ibexpeak, code was copy-pasted
and forked from bd82x6x. Since a custom ibexpeak/nvs.h was already made,
an accompanying globalnvs.asl is added here too without chromeos_acpi_t.
Change-Id: I16406516b51c13d49593bc8a3e1e5b868eea6f24
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48766
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Files under sb/ or soc/ should not have includes that tie those
directly to external components like ChromeEC os ChromeOS
vendorcode.
Change-Id: Ib56eeedaa9d7422e221efa9c8480ed5e12024bca
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48765
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Change-Id: I8d775d2d813cf92245f3be4d41b3295ca6da18ba
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48798
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Jason Glenesk <jason.glenesk@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
psp.h was first included when Stoney Ridge began loading the first
SMU firmware. That step was later moved from bootblock to romstage.
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Change-Id: Id646390ce377143d09455f797de1b149dbb615b5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48797
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add support for gpio driver for drobit
BUG=b:175351914
BRANCH=none
TEST=emerge-volteer coreboot
Signed-off-by: FrankChu <frank_chu@pegatron.corp-partner.google.com>
Change-Id: I54ba182c6da3db282961b3c72a4d2d11d1001e95
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48497
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
drobit memory table as follow:
value Vendor Part number
0x00 MICRON MT53E512M32D2NP-046 WT:E
0x00 HYNIX H9HCNNNBKMMLXR-NEE
0x01 MICRON MT53E1G32D2NP-046 WT:A
0x02 HYNIX H9HCNNNCPMMLXR-NEE
BUG=b:175351914
BRANCH=none
TEST=emerge-volteer coreboot
Signed-off-by: FrankChu <frank_chu@pegatron.corp-partner.google.com>
Change-Id: Icd9439f8449856d4ec6798a4e4310dd139bce05f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48496
Reviewed-by: Zhuohao Lee <zhuohao@chromium.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Update drobit device tree override to match schematics.
BUG=b:175351914
BRANCH=none
TEST=emerge-volteer coreboot
Signed-off-by: FrankChu <frank_chu@pegatron.corp-partner.google.com>
Change-Id: I48a3024df4270b111b90c4fb56847aad6e65bfa1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48495
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Zhuohao Lee <zhuohao@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Move gpio early init to bootblock_mainboard_early_init to make the
bootblock console work as early as possible.
Change-Id: I619f7d0e15adae284b606dd20c3c1f04f3eafd7b
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48801
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This reverts commit 1a0071c7115819302c7df3fa2c07b1ca971e515d.
Reason for revert:
UART pad configuration should not be done in common code, since it
could cause short circuits if the user configures a wrong UART index.
Change-Id: I6022935eaab748f82c6330be0729ff72f4880493
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48328
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
Add enable acp_i2s_use_external_48mhz_osc flag and then
WWAN sku will use external clock source at next build.
BUG=b:174121847
BRANCH=zork
TEST=build vilboz and check MISC_CLK_CNTL1.
Signed-off-by: John Su <john_su@compal.corp-partner.google.com>
Change-Id: Ida747938373f648524b1e7f34bc69e372a69c4f9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48556
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Signed-off-by: Huayang Duan <huayang.duan@mediatek.com>
Change-Id: I2c6ffe885717997540a0a9721310e355a3b6a87d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44704
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
Reference datasheet:
External Memory Interface (EMI).pdf, Document No: RH-A-2020-0055.
Signed-off-by: Huayang Duan <huayang.duan@mediatek.com>
Change-Id: I3b778698a09c999252fef3153ac1e869ea9d90cd
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44703
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
|
|
Memory PLL is used to provide the basic clock for dram controller
and DDRPHY. PLL must be initialized as predefined way.
First, enable PLL POWER and ISO, wait at least 30us, release ISO, then
configure PLL frequency and enable PLL master switch.
At last, enable control ability for SPM to switch between active and
idle when system is switched between normal and low power mode.
TEST=Confirm Memory PLL frequency is right by frequency meter
Signed-off-by: Huayang Duan <huayang.duan@mediatek.com>
Change-Id: Ieb4e6cbf19da53d653872b166d3191c7b010dca6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44702
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
|
|
Use the common block ACPI to further reduce the duplicate code.
Change-Id: If28d75cbb2a88363d70e3ae6a2cace46cb6bbbab
Signed-off-by: Marc Jones <marcjones@sysproconsulting.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48248
Reviewed-by: Jay Talbott <JayTalbott@sysproconsulting.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This reverts commit ccceb2250eeb820fccfb62d1f3ab407582d2e79f.
Reason for revert:
UART pad configuration should not be done in common code, since it
could cause short circuits if the user configures a wrong UART index.
Change-Id: Idc268debc60a027ed2f5a76e0de8ea2d1cde0fc4
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48327
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
Test results show that USB signals look better with these settings.
Yes, there's a macro in the devicetree now. All ports use the same
settings except for the overcurrent pin, so this avoids redundancy.
Change-Id: Ib0dafab88d8dcc05388b724f6a7183c13ac64934
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48694
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add devicetree configuration for G2TOUCH Touchscreen controller.
BUG=b:175513059
BRANCH=octopus
TEST=build bios, check i2c bus and verify touch screen works fine
Change-Id: Ib57597c4998f205c664e13befb4c44532b7dbd4f
Signed-off-by: rasheed.hsueh <rasheed.hsueh@lcfc.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48552
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
The latest version defined by TCG is 1.3.
Change-Id: Idb12e2212d6d38c720c8fe989678724c871af6ef
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45569
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Implement the ACPI PPI interface as described in
"TCG PC Client Physical Presence Interface Specification" Version 1.3.
Add a new Kconfig that allows to use the full PPI instead of the stub
version compiled in.
This doesn't add code to execute the PPI request, as that's up to the
payload with graphical UI support.
Tested on GNU/Linux 5.6 using the sysfs interface at:
/sys/class/tpm/tpm0/ppi/
Change-Id: Ifffe1d9b715e2c37568e1b009e86c298025c89ac
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45568
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add supported memory parts in the mem_parts_used.txt and generate the
SPD ID for the memory parts. The memory parts being added are:
MT53E512M32D2NP-046 WT:E
H9HCNNNBKMMLXR-NEE
MT53E1G32D2NP-046 WT:A
H9HCNNNCPMMLXR-NEE
BUG=None
TEST=Build the storo board.
Signed-off-by: Tao Xia <xiatao5@huaqin.corp-partner.google.com>
Change-Id: Ifd935865927bb9fccf95eb4924ca6986d0c19442
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48447
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Xuxin Xiong <xuxinxiong@huaqin.corp-partner.google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Update devicetree and gpio driving of boten that enable stylus
PEN detect signal is not dual-routed on Boten. Since the gpio_keys kernel
driver expects the pad to be owned by GPIO controller (i.e. configured for
GPIO IRQ), it cannot be configured for ACPI (i.e. SCI).
Thus, this change updates the GPIO configuration for GPP_C12 to
PAD_CFG_GPI_GPIO_DRIVER and device tree entry for PENH device to
use WAKEUP_ROUTE_GPIO_IRQ. Additionally, the signal is marked as active
low in the device tree entry to indicate to the kernel driver that the signal
is inverted.
Not dual routing the signal results in wake source not being added to
eventlog when pen removal results in wake from S0ix.
BUG=b:160752604
BRANCH=dedede
TEST=Build and check behavior is expected.
Signed-off-by: rasheed.hsueh <rasheed.hsueh@lcfc.corp-partner.google.com>
Change-Id: I74a17088da64c22ef1c74d201c80274fc65a44c9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48641
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Don't depend on the MTRR setup left over from FSP-M ExitTempRam.
Change-Id: I299123b3cd3c37b4345102c20fda77bf261892a2
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48673
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
|
|
Change-Id: I42ddea2c04bf1ecb2466db3d56d15d51bda486c8
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48660
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
|
|
Change-Id: I75f83bcc6c65a048e87f7295a66526eb384afc5d
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48692
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
This patch adds initial support for Alderlake Intel Pre-CEP
board called shadowmountain.
BUG=b:175808146
TEST=util/abuild/abuild -p none -t intel/shadowmountain -a -c max
Change-Id: I9cb650c88986badd6733b001d6f2a0e338421829
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48685
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Enable Runtime D3 for the volteer variants that have GPIO power control
of the NVMe device attached to PCIe Root Port 9.
Enable the GPIO for power control for variants that do not already have
it configured to allow the power to be disabled in D3 state.
BUG=b:161270810
TEST=tested on eldrid
Signed-off-by: Nick Chen <nick_xr_chen@wistron.corp-partner.google.com>
Change-Id: I941c8a9bb3221ad90528c323cd0f267dc77d2af3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48687
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Add a hook for SOCs to provide an IOAPIC MADT table. If the
SOC doesn't provide a table then a standard setting is used.
Change-Id: Ic818a634e4912d88ef93971deb4da5ab708c9020
Signed-off-by: Marc Jones <marcjones@sysproconsulting.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48246
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Jay Talbott <JayTalbott@sysproconsulting.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Add UPDs for eDP phy tunning adjust
BUG=b:171269338
BRANCH=zork
TEST=Build, verify the parameter pass to picasso-fsp
Signed-off-by: Chris Wang <chris.wang@amd.corp-partner.google.com>
Change-Id: I6df063f828447841ac9a6dba00a4aad2001f04df
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48731
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
|
|
Change static calculate_power() function to global and update the name
to common_calculate_power_ratio() for SOC ACPI code use.
Change-Id: I0e2d118ad52b36859bfc6029b7dee946193841f4
Signed-off-by: Marc Jones <marcjones@sysproconsulting.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48739
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Jay Talbott <JayTalbott@sysproconsulting.com>
|
|
When a different FSP binary was chosen in menuconfig, the split fd files
do not get updated. Thus, make them depend on `.config` to trigger a
rebuild when the config changes.
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: I54739eae50fa1a47bf8f3fe2e79334bc7f7ac3d6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48663
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Falling back to default values for Imon slope and offset for Drawcia
This is as per recommendation from ODM based on calibration
This reverts commit 2ac88f2347352c5dff0af18d5130dbdd6f032930.
BUG=b:175629526
BRANCH=dedede
TEST=Debug FSP confirms that values are reverted to default
Change-Id: I605acdcd0de2c5dfc28af2aea8cefc6b629c0925
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48737
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Vidya Gopalakrishnan <vidya.gopalakrishnan@intel.corp-partner.google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add support for gpio driver for galtic
BUG=b:170913840
BRANCH=dedede
TEST=emerge-dedede coreboot
Signed-off-by: FrankChu <frank_chu@pegatron.corp-partner.google.com>
Change-Id: I01bb95545705efab1a2adf1582b6293fd89e6420
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48684
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable Acoustic noise mitigation for madoo and set slew rate to 1/8
which is calibrated value for the board. Other values like PreWake,
Rampup and RampDown are 0 by default.
BUG=b:173765599
BRANCH=dedede
TEST=Correct value is passed to UPD and Acoustic noise test passes.
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Change-Id: I968d8d43016e3569835b0a777335fa1d5c135f87
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48721
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
galtic memory table as follow:
value Vendor Part number
0x00 MICRON MT53E512M32D2NP-046 WT:E
0x00 HYNIX H9HCNNNBKMMLXR-NEE
0x01 MICRON MT53E1G32D2NP-046 WT:A
0x02 HYNIX H9HCNNNCPMMLXR-NEE
BUG=b:170913840
BRANCH=none
TEST=emerge-dedede coreboot
Signed-off-by: FrankChu <frank_chu@pegatron.corp-partner.google.com>
Change-Id: I30b8fe3f14e1af7bb5760530477f9311c6a4ee62
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48655
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
gumboz is the dalboz/dirinboz follower.
update gumboz variant to align dirinboz settings.
BUG=b:174277853,b:173662179
BRANCH=zork
TEST=emerge-zork coreboot
Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com>
Change-Id: I80c03d531761c02b68bd127d889c3ace2dd9e99e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48642
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Kangheui Won <khwon@chromium.org>
|
|
UART pads already get configured in bootblock by the UART driver in soc
code. Thus, drop the duplicated code from the mainboard.
Change-Id: I95565a74e19d693a7d5ead81e72592cc4ca2038c
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48594
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
|
|
UART pads already get configured in bootblock by the UART driver in soc
code. Thus, drop the duplicated code from the mainboard.
Tested successfully on Clevo L141CU.
Change-Id: I05a459b0af79c75c31b1bb26ea1a1a40857ef9bf
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48593
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
|
|
Move sb_clk_output_48Mhz out of acp. It should be called unconditionally.
We may have another device need this clock e.g. superio chip.
BUG=b:174121847
BRANCH=zork
TEST= build passed
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I30ad6c60066f17cc83e7feb40675610f4853a022
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48722
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
If we have use external clock source for I2S, we don't need to enable
internal one. Add acp_i2s_use_external_48mhz_osc flag for the project
which uses external clock source.
BUG=b:174121847
BRANCH=zork
TEST= build passed
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: Ica68ee2da5a05231eb6db0218bd0f19907507273
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48637
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
