| Age | Commit message (Collapse) | Author |
|---|
|
Update submodule pointer to pull in newly-updated Braswell FSP.
Adjust FSP_FD_PATH for soc/cannonlake due to filename case change.
Change-Id: I02ee0d32fd4c04cd4971eff20fc5a7de3f9b07ec
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32420
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
|
|
Add FP_RST_ODL to early GPIO table, configured as low, so that the FPMCU
will get reset when coreboot enters bootblock.
BUG=b:130229952
BRANCH=none
TEST=Compiles (no Hatch device w/FP to test)
Change-Id: I8a8d8cc2c560f6518337f7500575fdc2265b6347
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32419
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
|
|
Lynx Point switched to doing mainboard-specific super I/O setup in the
bootblock with commit d893a2635fdd ("sb/intel/lynxpoint: Enable LPC/SIO
setup in bootblock"). The X10SLM+-F was added while that commit was in
review, and hence did not receive the necessary changes to SIO setup.
This patch has not been tested on hardware.
Change-Id: I7a648ec967dea2113cbbde1a93c1963ca6dd3c88
Signed-off-by: Tristan Corrick <tristan@corrick.kiwi>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32406
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
On EC end, we want to change this pin from push-pull to open-drain.
And since there is no external pull-up resistor on the board, we'll
have to configure this pin as internal-pull-up on AP end.
BUG=b:129306003
TEST=None
Change-Id: Ibc1f89fc25773220db009c6571400b01390dd756
Signed-off-by: Philip Chen <philipchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32292
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
FIT support takes more heap memory than most coreboot payloads.
Change-Id: Id17f25e94d97e937b0e9a9cee3dd1a8aef1d525d
Signed-off-by: Marty E. Plummer <hanetzer@startmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32392
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Add common SoC config.
Disable PCIe WiFi.
Add digitizer.
Turn off native SD card interface.
No WWAN.
Add DA7219 driver to Kconfig.
BUG=b:130310626
BRANCH=none
TEST=compiles (no Hatch ref or Kohaku device to test)
Change-Id: I17d5ba6ce4ec412384e4a1678474b8d26499ba40
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32405
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Not all Hatch variants utilize the SoC's native SD card support. Move
the support to board-specific variants instead of the base device tree.
BUG=none
BRANCH=none
TEST=compiles (no Hatch device to test with)
Change-Id: Iae24114aad2c4d042c25da6f8cb740ccc8960082
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32417
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Similar to hatch(CB:32278), this change sets SerialIo
config for UART0 to PchSerialIoSkipInit to skip initialization in
FSP.
This change also adds a device to kohaku override tree to ensure that
the settings in it take effect.
BUG=b:130310626
Change-Id: Ia25b45811be26d55fc0019e4cd22eb7310b5a4c4
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32398
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Enable acoustic noise mitgation for arcada platform,
the slow slew rates for Ia and Gt are fast time dived by 8.
BUG=b:131144464
TEST=waveform test and hardware validation result pass.
Signed-off-by: nathan chen <nathan_chen@wistron.corp-partner.google.com>
Change-Id: I37315ecfa245fce3085e62d1566ff037d8aa8ab4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32403
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Disable the POWER_OFF_ON_CR50_UPDATE option on sarien/arcada. This is
needed so that platform properly boots after doing a Cr50 firmware
update when running on battery.
BUG=b:126632503
BRANCH=none
TEST=Build coreboot on sarien/arcada.
TEST=Perform Cr50 firmware update on Sarien, confirm the platform boots
normally after sending TURN_UPDATE_ON to the Cr50.
Change-Id: I0b687285eb95070eaffb68611a7d98eb8434ce2c
Signed-off-by: Keith Short <keithshort@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32436
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Modify the POWER_OFF_ON_CR50_UPDATE Kconfig option so that specific
mainboard implementations can disable the option.
BUG=b:126632503
BRANCH=none
TEST=Build coreboot on sarien/arcada.
TEST=Perform Cr50 firmware update on Sarien, confirm the platform boots
normally after sending TURN_UPDATE_ON to the Cr50.
Change-Id: I3beefaae21de61e53ae232dbdc8ea9dbb2c78cd5
Signed-off-by: Keith Short <keithshort@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32435
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This change will save touchscreen power leakage 2-3mW in S0iX and
increase T2 display time delay to meet display panel requirement.
BUG=b:129899315
TEST= Measure touchscreen power from Sarien during S0iX
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I48419132ba734f20ad5cf484c2dda609570a6dd0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32330
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Sarien will change Melfas from HID to I2C and change address from
0x10 to 0x34. So we don't need VPD to separate Elan and Melfas
anymore.
BUG=b:131194574
TEST=boot up and check no Melfas HID device exist
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: Ic002f61b226743e1c18dbdbc51ce8b733916d8a0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32437
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
We want to disable touch for non-touch sku. We can use
strap pin GPP_B4 to identify it is connected with touch
or not.
touch sku: GPP_B4 is low
non-touch sku: GPP_B4 is high
BUG=b:131132419
TEST=boot up and check no touch device exist
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: If6681262c25e4b01e061a8520e38905d40345509
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32438
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Set CPU frequency from 1100MHz to 1989MHz to improve booting time.
BUG=b:80501386
BRANCH=none
Test=Boots correctly on Kukui
Change-Id: Id41c7ea8905c4db2537a5c32f96eb7c6b2c008ea
Signed-off-by: Tristan Shieh <tristan.shieh@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32397
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: You-Cheng Syu <youcheng@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The maximum CPU frequency is 1417MHz with current processor voltage
(0.8v). Set processor voltage to 1.05v for higher CPU frequency.
BUG=b:80501386
BRANCH=none
Test=Boots correctly on Kukui
Change-Id: I24ecdac2c85d3f012d9235449c0d727d727dc185
Signed-off-by: Tristan Shieh <tristan.shieh@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32396
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: You-Cheng Syu <youcheng@google.com>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
|
|
SSD reset pin had been added on DVT2, the power sequnence requires
toggle in boot stage.
BUG=b:130741066
TEST=Boot up with simulated DVT2 platform and confirm SSD can be
detected during warm reboot.
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: Ie734875a49b8b61f8b813c473d30cbcaf4dd13d1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32434
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Tune I2C params for I2C buses 5, 6, and 7 to ensure that the
frequency does not exceed 400KHz.
BUG=b:131132499, b:128998988
BRANCH=octopus
TEST=emerge-octopus coreboot chromeos-bootimage and measured frequency
under 400 KHz
Change-Id: Ie8cfba72a0654402ccb0274c00b44fbfa2deea21
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32404
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Add goodix touchscreen support
BUG=b:131082228
BRANCH=octopus
TEST=emerge-octopus coreboot and verify that touchscreen works on
bloog.
Change-Id: I0b3b481ca806b6452d67ace5dfe53f12a14ac3be
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32387
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Change-Id: I556d00e8b06f631a5ca51ae2b5ba646e5f536480
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32422
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add support of GPIO IRQ APIs.
Change-Id: I11715a93999012622a5e28455731cbe249ba8f2c
Signed-off-by: Shefali Jain <shefjain@codeaurora.org>
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Signed-off-by: Nitheesh Sekar <nsekar@codeaurora.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32241
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Update SPI enable/disable and configure clock
API for supporting all the blsp and qup for qcs405.
Change-Id: I39622571cb671f62312283a010129ceecb654f61
Signed-off-by: Shefali Jain <shefjain@codeaurora.org>
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Signed-off-by: Nitheesh Sekar <nsekar@codeaurora.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32240
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Fixes src/northbridge/intel/sandybridge/raminit_mrc.c:286:3: error:
implicit declaration of function 'enable_usb_bar'
Change-Id: I48bf59c56b518477a3fc0d75902fc58df6b7def7
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32400
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: Ic23eb57a4096d4301d7f9478d8e65aaeb233de7b
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32399
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Change-Id: I7669b8dc07b1aa5f00e7d8d0b1305b3de6c5949c
Signed-off-by: T Michael Turney <mturney@codeaurora.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32287
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
When coreboot checks the TPM and key-ladder state it issues a reboot of
the Cr50 with a delay parameter. Older Cr50 code doesn't support the
delay parameter and reboots immediately, which prevented coreboot from
running the mainboard specific code needed for the AP to come back up.
This change calls mainboard_prepare_cr50_reset() prior to sending the
VENDOR_CC_IMMEDIATE_RESET command.
This change also fixes a false error message from the coreboot log that
indicated "Unexpected Cr50 TPM mode 3" when the Cr50 key ladder is
disabled.
BUG=b:130830178
BRANCH=none
TEST=build coreboot on sarien and grunt platforms.
TEST=Load Cr50 v3.15, run 'gsctool -a -m disable; reboot'. Verify
corebot send the
VENDOR_CC_IMMEDIATE_RESET command and that the AP boots normally.
Verify event log shows "cr50 Reset Required"
TEST=Force Cr50 automatic update. Verify event log shows "cr50 Update
Reset".
Change-Id: Ib05c9cfde8e87daffd4233114263de5b30822872
Signed-off-by: Keith Short <keithshort@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32365
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Declare plaform level hook method before and after system sleep for
possible power management related usage.
BUG=N/A
TEST=pass with make what-jenkins-does
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: Ie63711748b6dbb99d34910824f2059464543e162
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32366
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: Ie8c5d5f7dd5b43becc144fd5e62d7de2f1ed3b80
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31432
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Without VBOOT_MEASURED_BOOT there is no need for these symbols.
Change-Id: I96391b7817c79f760713c67bc469164b5514879e
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32383
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Tested config:
Interleaved (config; status before, after):
DIMM{0 + 2}: ok, ok
DIMM{0 + 3}: Nok, ok
DIMM{1 + 2}: ok, ok
DIMM{1 + 3}: Nok, ok
DIMM{1 + 2 + 3}: ok, ok
DIMM{0 + 2 + 3}: ok, ok
DIMM{0 + 1 + 2}: ok, ok
DIMM{0 + 1 + 3}: Nok, ok
Not Interleaved:
DIMM{0 + 1 + 3}: Nok, Nok
DIMM{0 + 1 + 2}: ok, ok (with single ranked)
DIMM{0 + 1 + 2}: Nok, Nok (with only dual ranked)
DIMM{0 + 2 + 3}: Nok, ok
DIMM{1 + 2 + 3}: ok, ok
Change-Id: Ibf130a3d4b6f8fa816f7a5f06822a9b8807be3d4
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31007
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Commit 45d4b17 [nb/intel/sandybridge: Move southbridge code to bd82x6x]
moved early_pch_init() to the southbridge, but failed to include
early_pch.c for the non-native raminit case, which now fails to link.
As all boards default to native raminit, this was missed by the autobuilder.
Adjust early_pch.c to be compiled regardles of ram init type used
Test: build/boot google/stout with MRC ram init selected
Change-Id: I50db30fda9a1099fb434c04ea97bcc38f8455233
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32382
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
For full reset, use already defined full_reset() function.
Change-Id: Iec7dcf285f3cb1cdc8f48d348ff8496879625db5
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32377
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
This allows for serial console during the bootblock and enables
console in general for the bootblock.
Change-Id: I5c6e107c267a7acb5bf9cbeb54eb5361af3b6db4
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/30315
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Parameter passing is incorrect here, it should pass
complete StdHeader instead of attempting to fill
in HeapStatus that should be treated as a field private
to AGESA, based on where it is defined in the header
files.
Furthermore the while() loop did not evaluate the
return value. Feature can be brought back at a later
date after someone verifies it actually works correctly
across different stages.
Change-Id: Ib243b275f8700ecaeb330772c795d305c61899c5
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31484
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Each entrypoint to AGESA goes through the same sequence
and have same the function signature.
To avoid introducing bunch of preprocessor magic, rename
all the agesawrapper_amdXXX() functions that are actual
entrypoints to AGESA API, make them static, and provide
a single exposed entry function agesa_execute_state().
Change-Id: I96ae1874132da3843aa42c2f4e8a59ec771d3893
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31483
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change will save touchscreen power leakage 2-3mW in S0iX and
increase T2 display time delay to meet display panel requirement.
BUG=b:129899315
TEST= Measure touchscreen power from Arcada during S0iX
Change-Id: I4b8f3fdc0d107b080c5febe6fa5d29ea5d1ed0fc
Signed-off-by: Roy Mingi Park <roy.mingi.park@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32311
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
|
|
Add SMBIOS type 9 system slots into coreboot, the definiation is up to
date with SMBIOS spec 3.2
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: Ibcfa377c260083203c1daf5562e103001f76b257
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32293
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
This change is mainly to control PlatformDebugConsent FSP UPD.
PlatformDebugConsent is enabled if SOC_INTEL_CANNONLAKE_DEBUG_CONSENT != 0.
PlatformDebugConsent in FspmUpd.h has the details.
BUG=b:130203864
TEST=boot ok and PlatformDebugConsent can be controlled by Kconfig
Change-Id: Ib845b5e42bc78fb352a0c97c6301f2aeca522f29
Signed-off-by: Kane Chen <kane.chen@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32297
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
SOC_INTEL_DEBUG_CONSENT config is generally to enable default debug
interface of SoC.
Ex: USB DBC, DCI debug interface on cnl, whl, cml.
Change-Id: I313d80d6c63fd37164c63f78e9e69d3cb4a5566b
Signed-off-by: Kane Chen <kane.chen@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32337
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Linux remains using SPI1 and PWM ASL even if these devices are disabled.
SPI1 and PWM are disabled by Intel FSP.
Remove ASL code.
BUG=N/A
TEST=Boot Ubuntu on Intel CherryHill CRB
Change-Id: Iec2ca7520081d00bf7a53d58ee054aa6f23e5606
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/29417
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
|
|
Serial bus revision [Byte 3] and serial bus specific revision [Byte 9]
are not the same.
Change-Id: I366f62e6aa0e9c0dfbc1ec17adeebc42a0e777eb
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32329
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
|
|
Include pch.h in the source files instead in sandybridge.h.
Tested on Lenovo T520 (Intel Sandy Bridge).
Still boots to OS, no errors visible in dmesg.
Change-Id: I9e5b678e979a8d136d8d00b49486d0a882f77d81
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32065
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Change-Id: I2e1011d9ac93ed764b6c2aa425928a972ec2aa43
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32322
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: Ib843eb7144b7dc2932931b9e8f3f1d816bcc1e1a
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/26796
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: David Guckian
|
|
Change-Id: Iddba5b03fc554a6edc4b26458d834e47958a6b08
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32214
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: David Guckian
|
|
Change-Id: Ie21c390ab04adb5b05d5f9760d227d2a175ccb56
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32122
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
Also use macros instead of magic numbers.
Change-Id: I00bd687c487894c72d4e4363774dbcdfaf62dd54
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31310
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
The pci_or_configx function makes the code shorter and more readable.
Change-Id: Ic1ba250f8ac9fb75cf3252aec18af80842bda7dd
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32310
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Signed-off-by: Thejaswani Putta <thejaswani.putta@intel.com>
Change-Id: I15973ac28e9645826986cf63d2160eedb83024e4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32290
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Droid/Blorb supports keyboard backlight feature, so enable the ASL code.
BUG=b:130330141
BRANCH=octopus
TEST=Build and boot to OS, verify that the string 'KBLT' is in the DSDT.
Change-Id: I74684e3905d34b61fa4b851798dbca018f986e5a
Signed-off-by: Pan Sheng-Liang <sheng-liang.pan@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32298
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marco Chen <marcochen@google.com>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: David Wu <david_wu@quanta.corp-partner.google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This reverts commit 41dad286d846819242a84fc65faed2bbb35845ac. The change will make s0ix fail on Sarien/Arcada Platform.
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: I169bc6f41fba82fcf515267e8e1d08aa5ee2dce4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32391
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
When the components like LCM ID are not installed (i.e., NC), ADC will
return some value with much larger variation from standard value (out of
the tolerance we set). To support that, we should check tolerance only
on non-NC voltages.
Also improve the error messages so we can see the ADC raw values
instead of simple assertion error (which makes debugging more difficult
since we have to build another firmware image just to print the values).
BUG=None
TEST=Booted on Kukui and got correct SKU ID for NC LCMID.
BRANCH=None
Change-Id: I8d00956e0e3b48ddbcaa505dd3ade24720c3b4ad
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32353
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: You-Cheng Syu <youcheng@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Currently, Arcada only supports D3hot during S0iX and there is leakage
power around 5~10mW depending on SSD vendors.
To support D3cold for SSD during S0iX, one MOSFET will be added on DVT2
and two GPIOs are required to be configured.
GPP_H13 is to control SSD_SCP_PWR_EN(power enable) and GPP_H12 is to
control SSD reset.
BUG=b:130741066
TEST=Measure SSD power during S0iX from Arcada(DVT2)
Change-Id: I868590e9e85d5df07930a3681884e3fc3a5c4d50
Signed-off-by: Roy Mingi Park <roy.mingi.park@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32361
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Sandy- and ivybridge use the same mrc.bin that has the heap in an
awkward location.
Change-Id: If985a48c6703c8a86d8051e67595cf0fd409d99a
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32385
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Since there is no standardized naming scheme for the
FSP binaries, the option USE_FSP_REPO can't be used
on some platforms, because some of the filenames differ
and the build process awaits "Fsp_*.fd" as filename.
As a workaround, add the option -n to SplitFspBin.py,
which defines the basename.
Change-Id: Idc684ad00033ffafd1090fc32b23549ce9603b4f
Signed-off-by: Felix Singer <migy@darmstadt.ccc.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/30930
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Previously Haswell used a romcc bootblock and starting verstage in
romstage was madatory but with C_ENVIRONMENT_BOOTBLOCK it is also
possible to have a separate verstage.
This selects using a separate verstage by default but still keeps the
option around to use verstage in romstage.
Also make sure mrc.bin is only added to the COREBOOT fmap region as it
requires to be run at a specific offset. This means that coreboot will
have to jump from a RW region to the RO region for that binary and
back to that RW region after that binary is done initializing the
memory.
Change-Id: I3b7b29f4a24c0fb830ff76fe31a35b6afcae4e67
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/26926
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This puts the cache-as-ram init in the bootblock.
Before setting up cache as ram the microcode updates are applied.
This removes the possibility for a normal/fallback setup although
implementing this should be quite easy.
Tested on Google peppy (Acer C720).
Setting up LPC in the bootblock to output console on SuperIOs is not
done in this patch, hence BOOTBLOCK_CONSOLE is not yet enabled by
default.
Change-Id: Ia96499a9d478127f6b9d880883ac41397b58dbea
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/26859
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Checking for empty MTRR_DEF_TYPE_MSR as a proxy for proper CPU reset
is common across multiple platforms. Therefore place it in a common
location.
Change-Id: I81d82fb9fe27cd9de6085251fe1a5685cdd651fc
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32319
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Correct the SD and SATA assignments.
TEST=Boot Grunt
BUG=b:130788333
Change-Id: Ib75e1dbb0cd7f90a8d297d11d3a7c3bad47a8d21
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32355
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Hide some debug output behind CONFIG_DEBUG_RAM_SETUP. That way the
pre-ram console does not overflow.
Change-Id: Idc425f4d10443f6ee7f9b4da67eb6542069cc40c
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32318
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Change-Id: Ia4b7311f30f8ec951d02d3c31c30cf8895ed0eb2
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32312
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
I2C 1 is not being used in any of the octopus variants, so disable it.
BUG=none
BRANCH=octopus
TEST=Verify on meep and bloog
reboot and s0ix suspend successfully
Change-Id: I7ed5065cfd0b9780d13feb27cc78b8090d7a03a6
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32349
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
|
|
arcada is designed to operate at max power of 140 Watt. Hence set psys_max to 140W.
BUG=b:124792558
TEST=Build and boot arcada.
Change-Id: I280dfb81b3e25c7619a68db487e2b18867f52fda
Signed-off-by: nathan chen <nathan_chen@wistron.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32335
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
|
|
References to MAINBOARD_PCI_SUBSYSTEM_{DEVICE_ID,VENDOR_ID} were removed
in commits
dbd3132 sb/intel/{i82801g/i/j,bd82x6x}: Make use of generic set_subsystem()
00bb441 sb/intel/lynxpoint: Remove PCI bridge function
Change-Id: I72bba8406eea4a264e36cc9bcf467cf5cfbed379
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32107
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
As reported by Coverity Scan CID 1400679.
Change-Id: I526b78a0697b7eb3c3dc75974c3a3a714b3d343f
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32313
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Ensure Kohaku GPIO pins are configured correctly w/r/t Hatch. Implement the
base/override model for GPIOs (regular and early). The 'hatch' baseboard
contains the base GPIOs, and variants can override individual pads.
BUG=b:129707481
BRANCH=none
TEST=Compiles for all variants.
Change-Id: Ie5c83a0538d367ea11e9499f21cea41891d7a78e
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32326
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Integrated graphics id 0x3ea1 reported as unknown in bootblock stage,
make it correct.
BUG=N/A
TEST=Boot up into sarien platform and check with serial log, it shows
IGD: device id 3ea1 (rev 02) is Whiskeylake ULT GT1.
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: I2c4c697b108be7fa74736514ca71469a1ca29c22
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32320
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
|
|
Add SMBIOS type 16 table for physical memory array, there's two item had
been left over.ECC and max capacity, as of now we set it to fixed value
as all the platform support by Intel common code don't support ECC
memory and so far the biggest capacity is 32GB.
BUG=b:129485635
TEST=Boot up with Sarien platform and check with dmidecode, the
following is the result:
Handle 0x000D, DMI type 16, 23 bytes
Physical Memory Array
Location: System Board Or Motherboard
Use: System Memory
Error Correction Type: None
Maximum Capacity: 32 GB
Error Information Handle: Not Provided
Number Of Devices: 2
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: If9c5831956ef273c84d831a2b1572b3442eed961
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32286
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Match SMBIOS type 17 device locator with motherboard silk screen,using
"DIMM-A" and "DIMM-B" instead of "Channel-0-DIMM-0" and
"Chaneel-1-DIMM-0".
TEST=Boot up with sarien platform and run dmidecode to check SMBIOS
type 17 have expected output.
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: Ie2125c0381bd24d96f725f68cde93a53da8c94c8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32280
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Current SMBIOS type 17 device and bank locator string is like
"Channel-x-Dimm-x" and "Bank-x", x is deciminal number. Give silicon or
mainboard vendor a chance to replace with something matches with
silkscreen.
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: I54f7282244cb25a05780a3cdb9d1f5405c600513
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32279
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Sync acpigen.h content to match with laetst acpica, the link is
https://github.com/acpica/acpica/blob/master/source/include/amlcode.h,
and revision is 20190405. The purspose of the change is just make spec
up to date.
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: If5f5da70eb66472ddf5df0d72ca85de41faac128
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32328
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
GPIO pin GPP_C23 is used as level trigger but not edge trigger, also it
is not inverted, correct it here. According to board schematic, GPP_C23
connected with 3.3v pull up, so the pin is low active.
BUG=b:128554235
TEST=Boot up arcada platform with stylus keep on touching the screen,
the touch screen is still functional once in OS stage. Without change,
touch screen is not functional at same scenario.
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: I2bee664198057e3997dda181a16b9a0388067036
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32347
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Bora Guvendik <bora.guvendik@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The EC can return a board ID value similar to the Chrome EC.
In order to use this for the board version returned by SMBIOS
this commit implements the board_id() function for mainboards
that use this EC.
BUG=b:123261132
TEST=Check /sys/class/dmi/id/board_version to see that it
is reflecting the value that the EC provides.
Change-Id: I3fbe0dc886701f37d2424fe7a2867fd860fa1ec0
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32276
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable the Kconfig option to automatically read the board ID
and populate it into the SMBIOS tables.
BUG=b:123261132
TEST=verify current board id from the OS:
cat /sys/class/dmi/id/board_version
rev1
Change-Id: Id41631bfaa627ca9d5034e2ebe93f8ace2ffdad8
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32277
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This progress code enables keyboard backlight control that
otherwise would only work 30 seconds after boot. This code
is already defined but it was not being sent by coreboot.
It is run in the "post device" step between the other defined
progress codes.
BUG=b:130754032
Change-Id: Ica6c622e568cb236c17bf3edb6639d0177510846
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32348
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
The platform supports Virtualization Technology for Directed I/O.
Generate DMAR acpi table if VT-d feature is enabled.
BUG=b:130351429
TEST=Booted to kernel and verified the DMAR table contents.
Change-Id: I4e1ee5244c67affb13947436d81628c5dc665c9e
Signed-off-by: John Zhao <john.zhao@intel.com>
Signed-off-by: Pratik Prajapati <pratikkumar.v.prajapati@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31917
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
|
|
Move the southbridge code to bd82x6x folder similar to the lynxpoint
implementation.
Tested on Lenovo T520 (Intel Sandy Bridge).
Still boots to OS, no errors visible in dmesg.
Change-Id: I8afc9f966033f45823f5dfde279e0f66de165e93
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32035
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Set default configuration to low for gpio_178, and can remove the
override setting for bobba/bloog/fleex/meep/phaser.
For ampton, Change-Id I64a67f73564188ad0548a1a770169ef2bca47453 (
mb/google/ampton: Fix polarity of EN_PP3300_WLAN_L signal.)
modified the pin setting.
TEST=verified that boot into OS on meep board.
suspend/resume, reboot, and no failure found.
Change-Id: I7668ff4817edfca5c6cea63db779fcea21c7af92
Signed-off-by: Wisley Chen <wisley.chen@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32247
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Write protection (get_write_protect_state) was hard-coded to 0 and
should be fixed to read from correct GPIO (PERIPHERAL_EN0 from
schematics).
BUG=b:130681408
TEST=make -j; boots on Kukui Rev2.
BRANCH=None
Change-Id: I75b98b1d587abe5e8cdf3df28ea661bc1ffa19f9
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32336
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: You-Cheng Syu <youcheng@google.com>
Reviewed-by: Daisuke Nojiri <dnojiri@chromium.org>
Reviewed-by: Joel Kitching <kitching@google.com>
|
|
This patch adds the PCI device ID for cometlake in dsp.c
Change-Id: Ia28e3b9d1dc27ffcf24dfb2ef1efa9ae9c4027c8
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32321
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
|
|
This patch ensures to follow Intel SDM Vol 3B Sec 18.7.3 to
calculate nominal TSC frequency.
As per SDM recommendation:
For any processor in which CPUID.15H is enumerated and
MSR_PLATFORM_INFO[15:8] (which gives the scalable bus frequency) is
available, a more accurate frequency can be obtained by using CPUID.15H
This patch also adds header file to capture Intel processor model number.
BUG=b:129839774
TEST=Boot ICL platform and calculate TSC frequency using below methods
1. TSC freq calculated based on MSR 0xCE
tsc: Detected 1600.000 MHz processor
2. TSC freq calculated based on CPUID 0x15
tsc: Detected 1612.800 MHz TSC
Method 2 actually reduce ~25ms of boot performance time.
Note: Method 2 is recommended from gen 6 processor onwards.
Change-Id: I9ff4b9159a94e61b7e634bd6095f7cc6d7df87c7
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32283
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
|
|
GPT4 is a 32-bit timer and the counter of GPT4 will overflow in about
330 seconds (0xffffffff / 13MHz). Timer and delay functions will not
work properly if the counter overflows. To fix that we should use the
64-bit timer (GPT6).
BUG=b:80501386
BRANCH=none
Test=emerge-elm coreboot; emerge-kukui coreboot
Change-Id: I9f080e47253a1b1bab4636a45cb86c8666a25302
Signed-off-by: Tristan Shieh <tristan.shieh@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32245
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: You-Cheng Syu <youcheng@google.com>
|
|
Change VmxEnable UPD values based on Kconfig ENABLE_VMX
and remove it from Devicetree and chip.h
Remove Vmx dependency on Vt-d
Change-Id: I4180c2270038a28befd6ed53c9485905025a15ba
Signed-off-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32117
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Implement required soc side API to enable VMX support using CPU_COMMON
BUG=b:124518711
TEST= read msr 0x3a and verify vmx is enabled (value should be 5).
Change-Id: I33dbffa6301afabd688080751ba3b85a43e00156
Signed-off-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31928
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Use common code to detect ACPI S3.
Tested on Lenovo T520 (Intel Sandy Bridge) with Change
I8afc9f966033f45823f5dfde279e0f66de165e93 applied as well.
Still boots to OS, no errors visible in dmesg and S3 resume is working.
Change-Id: I283a841575430f2f179997db8d2f08fa3978a0bb
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32037
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Use common code to detect ACPI S3.
Untested.
Change-Id: I618d4c25adb0d2b9bbd59a3b3b84beac78db1916
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32315
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
This patch performs MP initialization by FSP using coreboot MP
PPI service.
BUG=b:74436746
TEST=Able to perform MP initialization on WHL and CML platform.
Change-Id: I530d50e5aacc3cb9b625df14a50d4c5923e3fb4d
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32301
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
|
|
Kukui is using MIPI display panel and needs some identifier to tell
payloads which LCD module is installed, and to select right kernel
device tree. Following Scarlet, the decision is to embed LCD module ID
as part of SKU ID.
The LCM ID is using a different voltage mapping table from the rest.
Considering the complexity in computation of SKU ID, it is better to
move the cache logic from get_index to caller.
Also revise the mapping table since ADC on 8183 only supports 12
levels.
BUG=b:129299873
TEST=make -j; boots on Kukui Rev2 unit.
Change-Id: Ib0c00bc8ce3c71c445c5c4561403ce8ef4dd5844
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32263
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The external RTC was removed on the mainboard as it is not needed.
Remove the usage of the driver for RX6110SA as well.
Change-Id: Ia476e58c0b0f343d4e9e4fa6039bf82b194a87d3
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32302
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Uwe Poeche <uwe.poeche@siemens.com>
|
|
With commit
'4074ce0cc7 (intel/apollolake: Add HDA to disable_dev function)'
FSP is now requested to switch off HDA PCI device if it is disabled in
devicetree. Doing so results in a warm restart. Normally this event
will be stored in CMOS RAM (if the descriptor is configured to do so)
and therefore no further resets are requested by FSP on the next boots
as long as CMOS RAM is kept alive.
The Siemens mainboards based on Apollo Lake do not have a CMOS battery
and therefore the CMOS is not backed up. This leads to reset requests
from FSP after PCI enumeration on every boot. To avoid this reset enable
HDA in devicetree for these mainboards. Though we do not have any usage
of HDA it should not be an issue that the HDA device is now enabled. The
benefit is though that no reset is requested anymore by FSP.
Change-Id: I637c7c01d73350700c6066fee74fecbb5b93b221
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32295
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Uwe Poeche <uwe.poeche@siemens.com>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Based on the power rail discharge times measured on hatch,
update the assertions widths that have to be programmed in SoC.
BUG=b:129328209
TEST=warm/cold reboot and S3 are working fine on hatch.
Change-Id: I3c6dce0a942e6dcd9e55ef5e58a7e9e8d2b0a1e3
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32266
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Laser would prefer to use different SAR values. Since Laser
sku id is 5.
BUG=b:130381493
BRANCH=octopus
TEST=build
Change-Id: I5cce38a191edfb235e274db3c788c58b65e0ebe1
Signed-off-by: peichao.wang <peichao.wang@bitland.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32296
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This sneaked in after we made unknown arguments to CONFIG() an error.
Change-Id: Ia1de78ce1d3277c7b094c3283455f4b56f3a3fbb
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32314
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Use common code to detect ACPI S3.
Tested on Thinkpad X60.
Change-Id: Ia759a9ed141efc8130860300f2a8961f0c084d70
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32041
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Use common code to detect ACPI S3.
Untested.
Change-Id: I87ac56e4ba1fb83761786d5f32a0fc308ee9718a
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32039
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Use common code to detect ACPI S3.
Untested.
Change-Id: I2264c087b317f70506817b5458295a17e83b1efc
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32038
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add a common detect_s3_resume function.
Will be used by other southbridge code.
TODO: Merge with soc/intel/common/*/pmclib
Tested on Lenovo T520 (Intel Sandy Bridge) with Change
I283a841575430f2f179997db8d2f08fa3978a0bb applied as well.
Still boots to OS, no errors visible in dmesg and S3 resume is working.
Change-Id: I88023af522afac8164f068b0fbe0eac601aef702
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32036
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
This patch removes multiple enable/disable function definitions and
make use of single function with argument to know feature status
(enable/disable).
Change-Id: I502cd2497b07e9de062df453ecbb9c11df692f5a
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32282
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch replaces multiple IA32_PERF_CTL programming with single
helper function.
TEST=Build and boot WHL and CML platform.
Change-Id: I212daa61aa11191dd832630461b517d3dbedd6e1
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32281
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Restore Goodix devicetree config because of the
missing Goodix config when moving from baseboard
devicetree to board level overridetree. And move
PENH from I2C#2 to I2C#1.
BUG=b:124460799
BRANCH=None
TEST=local build and tested with Goodix touch screen
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: Ic028c5d7b687a069d7f0510897bea91dca58e91f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32265
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
