Age | Commit message (Collapse) | Author |
|
This change adds the cbfs_cache region into the x86 memlayout. The SoC
or mainboard can decide how big the region should be by specifying
CBFS_CACHE_SIZE.
BUG=b:179699789
TEST=Build guybrush and verify cbfs_cache region wasn't added.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I268b6bc10906932ee94f795684a28cfac247a68c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56578
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Addresses in AMD fw table with EFS gen2 are relative addresses, but
PSP doesn't accept relative addresses in update_psp_bios_dir().
Check for EFS gen2 and convert them as needed.
BUG=b:194263115
TEST=build and boot on guybrush and shuboz
Signed-off-by: Kangheui Won <khwon@chromium.org>
Change-Id: I95813beba7278480e6640599fcf7445923259361
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58316
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Add backlight support in ps8640 through the AUX channel using eDP
DPCD registers.
BUG=b:202966352
BRANCH=trogdor
TEST=verified firmware screen works on homestar rev4
Change-Id: Ief1bf56c89c8215427dcbddfc67e8bcd4c3607d2
Signed-off-by: xuxinxiong <xuxinxiong@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58624
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Currently, the address size field of AT24 NVM is incorrect, and
Linux v5.10 kernel logs the message below:
at24 i2c-PRP0001:01: Bad "address-width" property: 14
The valid size of the AT24 NVM is 16 bits so modify the value from
0x0E to 0x10.
TEST=Boot brya and check the kernel log and see "Bad address-width"
error message is not shown.
Signed-off-by: Varshit B Pandya <varshit.b.pandya@intel.com>
Change-Id: I6c1ed5334396e0ca09ea0078426a7b5039ae4e8b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58769
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
|
In order to let the ec passing the key event like recovery and power key
to the OS, we need to include EC_ENABLE_MKBP_DEVICE to generate the MKBP
device.
BUG=b:204519353, b:204512547
BRANCH=None
TEST=pressed recovery key and power button in the OS and checked the UI
behavior.
Change-Id: Ia1d0b9b301994ad9a0f4bf28b75ab0310a1d63a0
Signed-off-by: Zhuohao Lee <zhuohao@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58744
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
PCIe root ports #5 (00:1c.4) and #6 (00:1c.5) are not used on this
mainboard and are not routed either, so remove them from the devicetree
completely. PCIe root port #7 (00:1c.6) is connected and used. Add the
missing settings for L1 substates and latency reporting to disable these
features for this port as well.
Change-Id: I06f59f0369ffcd958b5fe12bb3c646d37103811f
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58568
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
There are a bunch of devices in the devicetree that are disabled in
FSP-S and not used on this board. Having them around in the devicetree,
even if disabled, is not necessary and leads to a message in the log
(left over static devices...check your devicetree).
This commit cleans up devicetree.cb and removes all unused and disabled
devices.
Change-Id: Ia5ffb382e3524e61b8583aca801063942fe2f247
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58567
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
|
|
Add DDR5 and LPDDR5 memory type checks while calculating bus width
extension (in bits).
Additionally, update all caller functions of
smbios_bus_width_to_spd_width() to pass `MemoryType` as argument.
Update `test_smbios_bus_width_to_spd_width()` to accommodate
different memory types.
Create new macro to fix incorrect bus width reporting
on platform with DDR5 and LPDDR5 memory.
With this code changes, on DDR5 system with 2 Ch per DIMM, 32 bit
primary bus width per Ch showed the Total width as:
Handle 0x000F, DMI type 17, 40 bytes
Memory Device
Array Handle: 0x0009
Error Information Handle: Not Provided
Total Width: 80 bits
Data Width: 64 bits
Size: 16 GB
...
BUG=b:194659789
Tested=On Alder Lake DDR5 RVP, SMBIOS type 17 shows expected `Total Width`.
Change-Id: I79ec64c9d522a34cb44b3f575725571823048380
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58601
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Rob Barnes <robbarnes@google.com>
|
|
Add new memory parts in the mem_parts_used.txt and generate the
SPD ID for the parts. The memory parts being added are:
1. Hynix H5ANAG6NCJR-XNC
2. Micron MT40A512M16TB-062E:R
3. ADATA 4JQA-0622AD
BUG=b:199469240
BRANCH=firmware-zork-13434.B
TEST=FW_NAME=vilboz emerge-zork coreboot chromeos-bootimage
Signed-off-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
Change-Id: I57cca403800d9731a7b689ac9773a7940e83904e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58690
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
|
|
This helper method makes the code a bit cleaner.
BUG=b:179699789
TEST=none
Suggested-by: Julius Werner <jwerner@chromium.org>
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: Ie442217eba2e8f99de1407d61f965428b5c6f3bf
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58761
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
CSE EOP will fail if the CSE is disabled (CB:52800)
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: Ic00fdb0d97fefac977c0878d1d5893d07d4481ea
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57149
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Introduce the `dptf_enable` devicetree setting to set the DPTE GNVS
field, as newer Intel platforms do.
Change-Id: I88b746c64ca57604f946eefb00a70487a2fb27c0
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57988
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
|
|
Use `bool` type where applicable.
Change-Id: I4d5422c16381676738b8614e8e50737b59739921
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57987
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
|
|
This removes the need for a Kconfig value.
Change-Id: Ia9f39aa1c7fb9a64c2e5412bac6e2600b222a635
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58684
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Compatible headphone codec "Realtek ALC5682I-VD" and "ALC5682I-VS"
BUG=b:202463494
BRANCH=dedede
TEST=ALC5682I-VD or VS audio codec can work normally
Signed-off-by: Zhi Li <lizhi7@huaqin.corp-partner.google.com>
Change-Id: Ib808ddadef1029d3f06eb2d68164243c386d4905
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58643
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Weimin Wu <wuweimin@huaqin.corp-partner.google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Some brya0 units have HPS fitted and connected to PCH I2C2, rather than
a user-facing camera.
Because HPS uses I2C address 0x51, which may conflict with the
user-facing camera EEPROM, introduce a new fw_config bit to indicate
whether HPS is present.
BUG=b:202784200
TEST=FW_NAME=brya0 emerge-brya coreboot chromeos-bootimage
TEST=ectool cbi set 6 0x28191 4 # set bit 17 for HPS
TEST=flashrom -p internal -w image-brya0.serial.bin
Signed-off-by: Dan Callaghan <dcallagh@google.com>
Change-Id: I322548bcfccf16ba571396bc88fd6fc03c036a4e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58646
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Remove unused code and comment to align with the latest MTK memory
reference code which is from MTK internal dram driver code without
upstream.
version: Ib59134533ced8de09d23dd9f347c934d315166e2
TEST=boot to kernel
Signed-off-by: Ryan Chuang <ryan.chuang@mediatek.corp-partner.google.com>
Change-Id: I95ab3cf8809ad22a341ceb7fd53a68e13fb0420d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58635
Reviewed-by: Rex-BC Chen <rex-bc.chen@mediatek.corp-partner.google.com>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=b:140165023
Change-Id: Idb4613dc08c8dee6c92b4dabb39c2f5c189471aa
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58770
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Modify print_me_fw_version to get ME firmware version by
calling it.
Tested=On a not yet to be public platform, verified the function
can get ME FW version successfully.
Signed-off-by: Johnny Lin <johnny_lin@wiwynn.com>
Change-Id: I50d472a413bcaaaa085955657bde6a0e6ec2c1db
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58520
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
The idea here is to capture the various boot entities prior
to IA cpu reset.
BUG=b:182575295
TEST=Boot to OS, check cbmem -t output
Signed-off-by: Bora Guvendik <bora.guvendik@intel.com>
Change-Id: If89befa362d7852a2c0743d05155a0b6c1634672
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57969
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Enable DRIVERS_GENESYSLOGIC_GL9755 support for brask.
BUG=b:197385770
TEST=build pass
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: If421e0df058b6f2b87267d5e3822940b90062f71
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58729
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Add probe function for the "VS" version of the audio amplifier so taeko
can recgonize MAX98357 with ALC5682I_VS.
BUG=b:202913837
TEST=FW_NAME=taeko emerge-brya coreboot and check taeko can recgonize
MAX98357 with ALC5682I_VS
Signed-off-by: Joey Peng <joey.peng@lcfc.corp-partner.google.com>
Change-Id: Id4ff2003ee6a6f6f4ad98694996689e1a84092c5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58645
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: YH Lin <yueherngl@google.com>
|
|
Add wifi sar for kracko
BUG=b:194460420
TEST=emerge-dedede coreboot-private-files-baseboard-dedede coreboot chromeos-bootimage
Change-Id: I83bca544c9f71142f95ea1137f732c182b3f29b7
Signed-off-by: Robert Chen <robert.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58522
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Henry Sun <henrysun@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Shou-Chieh Hsu <shouchieh@google.com>
Reviewed-by: Kevin Chiu <kevin.chiu.17802@gmail.com>
|
|
Add DDR5 and LPDDR5 memory technology into the SMBIOS Memory Type
table.
Change-Id: I1ec442cf0bd830db99e3636445724b6be01c5564
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58576
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Make use of `smbios_bus_width_to_spd_width()` for filling DIMM info.
Additionally, ensures dimm_info_util.c file is getting compiled for
romstage.
TEST=dmidecode -t 17 output Total Width and Data Width as expected.
Change-Id: I7fdc19fadc576dec43e12f182fe088707e6654d9
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58655
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
commit 6af980a2a
(drivers/intel/fsp2_0: Allow `mp_startup_all_cpus()` to run serially)
drops CB_SUCCESS check for mp_run_on_all_aps function hence, this
changes bring back the required return type against CB_SUCCESS.
Change-Id: I9fc81e6a7eebbf0072ea2acb36b3c33539b517a7
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58757
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
GPP_B14 is used by buzzer and should be set to NF1 'SPKR'.
BUG=b:198998974
TEST=emerge-brask coreboot depthcharge and verify if the buzzer beeps.
Signed-off-by: Alan Huang <alan-huang@quanta.corp-partner.google.com>
Change-Id: I84978af152a7117c1f3398a9b7adde161db058dd
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58692
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
The reason cbfs_cache was disabled on x86 was due to the lack of
.data sections in the pre-RAM stages. By using
ENV_STAGE_HAS_DATA_SECTION we enable x86 to start using the cbfs_cache.
We still need to add a cbfs_cache region into the memlayout for it to
be enabled.
BUG=b:179699789
TEST=Build guybrush and verify cbfs_cache.size == 0.
Suggested-by: Julius Werner <jwerner@chromium.org>
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I74434ef9250ff059e7587147b1456aeabbee33aa
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56577
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
With cr50 fw 0.3.22 or older version, it needs to disable autonomous
GPIO power management and then can update cr50 fw successfully.
BUG=b:202246591
TEST=FW_NAME=anahera emerge-brya coreboot chromeos-bootimage.
Signed-off-by: Wisley Chen <wisley.chen@quanta.corp-partner.google.com>
Change-Id: I9137b6264ee80bc9e00dfdc3ab3926bccb4bf47c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58695
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
The PCI-SIG engineering change requirement provides the ACPI additions
for firmware latency optimization. This change adds additional ACPI DSM
function with both of FW_RESET_TIME and FW_D3HOT_TO_D0_TIME to the
USB4/TBT topology which has the same implementation on Tiger Lake in
commit I5a19118b75ed0a78b7436f2f90295c03928300d7.
BUG=b:199757442
TEST= It was validated that the first connected device waits only 50ms
instead of 100ms and all functions work on Alder Lake platform boards.
Signed-off-by: John Zhao <john.zhao@intel.com>
Change-Id: I0c8977c96de27ab0e554469eba658660975b8493
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58098
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Used H1 firmware where the last version number is 0.0.22, 0.3.22 or
less to production that will need to disable autonomous GPIO power
management and then can get H1 version by gsctool -a -f -M
BUG=b:201266532
TEST=FW_NAME=kano emerge-brya coreboot and verify it builds
without error.
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: If6783e0df1404c9a353061fb564210aa0d12896e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58682
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Set the `PcieRpLtrEnable` option to enable the LTR capability on all PCH
PCIe root ports.
TEST=Verify LTR capability enabled in `DevCap2` using `lspci -vv`
Change-Id: I07ea37d178ea61d904c4f131fdea31479e899ef3
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58326
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Map each PCIe clock source to the corresponding root port. Also, correct
the CLKREQ# mapping for clock sources not associated to any CLKREQ# pin.
The default `PcieClkSrcClkReq` value of 0 corresponds to CLKREQ# 0.
TEST=Check that Linux sees the same PCIe devices with this commit:
- All 5 onboard Ethernet NICs
- BMC
- Two random graphics cards in PEG0 and PEG1 slots
- M.2 M NVMe SSD
Change-Id: I0515877a36d42fb8858a0f0b3c0af1199a18d9af
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58368
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
The current check for XDCI enabled uses a static device path to an
internal PCI device at a very late point in the boot flow. At this
time the devicetree has been processed and disabled devices have been
already removed. If this device (00:15.1, XDCI) is disabled in
devicetree this will trigger the message
'BUG: check_xdci_enable requests hidden 00:15.1' in the log.
This looks weird and is wrong since it is not a bug to disable this
device when it is not needed.
To avoid this look up the devicetree by a tree walk instead of using
a static value for the devicetree.
Change-Id: If193be724299c4017e7e10142fac8db9fac44383
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58524
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Correct the PCIe clock source configuration as per the schematics.
Apparently, FSP does not turn off unused PCIe clock sources when using
SPS (Server Platform Services) firmware, but it does when using CSME
firmware.
TEST=BMC and Ethernet NICs get detected when using CSME firmware.
Change-Id: Id25a34816f512510640db95251a7a792c1eebe62
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58065
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
As per MP service specification, EDK2 is allowed to specify the mode
in which a 'func' routine should be executed on APs.
`SingleThread` sets to 'true' meaning to execute the function one by
one (serially) or sets to 'false' meaning to execute the function
simultaneously.
MP service API `StartupAllAPs` was designed to pass such options as
part of function argument.
But another MP service API `StartupAllCPUs` doesn't specify any such
requirement. Running the `func` simultaneously on APs results in
a coherency issue (hang while executing `func`) due to lack of
acquiring a spin lock while accessing common data structure in
multiprocessor environment.
BUG=b:199246420
Change-Id: Ia95d11408f663212fd40daa9fd9b0881a07f1ce7
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Signed-off-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57343
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
This reverts commit 0a1602217fd0d60c59a497cb83a23b44cf4973d9.
EC region is required in order to provide unified coreboot image for
Chrome and Windows SKU RVP's. Also removing EC region causes a regression
for ADL-P platforms.
With this patch EC region is included back into flash map.
Change-Id: I0f7f2b5dd392b08e1978a3b3f3236eac0dab1f12
Signed-off-by: Bernardo Perez Priego <bernardo.perez.priego@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58661
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
|
|
Add fw_config probe for MIPI OVTI2740 camera
BUG=b:194926283
TEST=FW_NAME=kano emerge-brya coreboot
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: Ic5a7cebf1f5c847c01e951a237af691e0ad6c73d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58619
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Compiletime errors > runtime errors.
Change-Id: I1db0a8f01eaecf012e5444c03f8d4e2bb6e42a77
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58649
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
The Intel icelake rvp boards actually rely on this but this failure
was hidden in a runtime error instead of a compile time error, due to
weakly linked functions.
Change-Id: Idbbe774efa1515ce1d34ce2ce8f87953300a3312
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58662
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=b:202784200
TEST=FW_NAME=taeko emerge-brya coreboot chromeos-bootimage
Signed-off-by: Dan Callaghan <dcallagh@google.com>
Change-Id: I400719d762b001811f809f9549fd030dff9928d0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58647
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Not all platforms need to generate power resources, but the code does
not get optimized out at build time because the devicetree gets
compiled into a linked list. As this code pulls in some heavy ACPI
dependencies that is even implemented with weak empty function it
makes sense to optimize out this code using a Kconfig constant.
This saves 1.5K in ramstage size on gigabyte/ga-945gcm-s2l.
Change-Id: I82289aa7e6e82318417f3b827b86182891dfc2a6
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58657
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Currently, the AMD SDLE stardust test fails with incorrect VDD/SOC
scale/offset value, it needs to update the two load line slope
settings for the telemetry.
AGESA sends these values to the SMU, which accepts them as units of
current. Proper calibration is determined by the AMD SDLE tool and the
Stardust test.
VDD scale: 92165 -> 73457
VDD offset: 412 -> 291
SOC scale: 30233 -> 30761
SOC offset: 457 -> 834
BUG=b:200194315
BRANCH=guybrush
TEST=emerge-guybrush coreboot chromeos-bootimage
pass AMD SDLE/Stardust test
Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com>
Change-Id: If53c173000a276a80247ccb08736280a25948939
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58600
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
EN_PWR_FP is used to enable power to the FPMCU. This frees up GPIO_32
for other uses.
This move applies to all board except:
* Guybrush
* Nipperkin board version 1
Add callbacks for variants to override fpmcu shtudown gpio table and
fpmcu disable gpio table.
BUG=b:202992077
TEST=Build and boot to OS in Guybrush and Nipperkin. Ensure fingerprint
still works.
Change-Id: I4501554da0fab0cb35684735e7d1da6f20e255eb
Signed-off-by: Rob Barnes <robbarnes@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58660
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
GSC_SOC_INT_L gpio is used by Google Security Chip (GSC) to interrupt
SoC when the SoC is in S0 state. Hence use GPIO_85 which is in S0 domain
and save the GPIO_3 in S5 domain for other use-cases. This move applies
to all board except:
* Guybrush
* Nipperkin board version 1
Update the GPIO configuration, device tree configuration accordingly.
BUG=b:202992077
TEST=Build and boot to OS in Guybrush and Nipperkin. Ensure that the SoC
<-> TPM communication is working fine.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: I019f10f2f457ab81bcff77ce8ca609b2b40cb2ea
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58638
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Rob Barnes <robbarnes@google.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
GPIO overrides are defined for verstage. But the overrides are neither
enabled nor applied during verstage. Enable the overrides and apply them
during verstage.
BUG=None
TEST=Build and boot to OS in Guybrush. Perform suspend/stress, warm and
cold reboot cycling for 10 iterations each. Ensure that all the PCIe
devices are enumerated fine.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: I510313bf860d8d55ec3b04a9cfdfa942373163f9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58637
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Rob Barnes <robbarnes@google.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
Modify IPC sub command to 2 from 0 for reading LPM requirement from PMC.
Reference:
https://github.com/otcshare/CCG-ADL-Generic-Full
ClientOneSiliconPkg\Include\Register\PmcRegs.h
#define V_PMC_PWRM_IPC_SUBCMD_GEN_COMM_READ 2
It is consumed in below.
ClientOneSiliconPkg\IpBlock\Pmc\Library\PeiDxeSmmPmcLib\PmcLib.c
Change-Id: I58509f14f1e67472adda78e65c3a2e3ee9210765
Signed-off-by: Ethan Tsao <ethan.tsao@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58317
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Used H1 firmware where the last version number is 0.0.22, 0.3.22 or
less to production that will need to disable autonomous GPIO power
management and then can get H1 version by gsctool -a -f -M
BUG=b:200918380
TEST=USE="project_gimble emerge-brya coreboot" and verify it builds
without error.
Signed-off-by: Mark Hsieh <mark_hsieh@wistron.corp-partner.google.com>
Change-Id: I83cc1a5d80bf23d052e83c9791ef866966a3d9b5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58626
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Since the iGPU PCI device IDs for AMD Renoir (family 17h, model 60h) and
Lucienne (family 17h, model 68h) are already defined in pci_ids.h, also
add them to the pci_device_ids list in the common AMD graphics support
block.
TEST=None
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I1c554d21eece182ecea7b09b45b7aa8a733425d5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58631
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
Add new memory parts in memory_parts_used.txt and generate SPD id for
these parts:
Hynix H54G46CYRBX267
Samsung K4U6E3S4AB-MGCL
BUG=b:204015941
TEST=run part_id_gen to generate SPD id
Change-Id: I78ec575d354a5ae7c014a6050364d0a5214e4e92
Signed-off-by: Wisley Chen <wisley.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58563
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Henry Sun <henrysun@google.com>
|
|
Add new memory parts in the mem_list_variant.txt and generate the
SPD ID for the parts. The memory parts being added are:
1. K4U6E3S4AB-MGCL
2. H54G46CYRBX267
BUG=b:204023388
BRANCH=firmware-keeby-14119.B
TEST=FW_NAME=driblee emerge-keeby coreboot chromeos-bootimage
Signed-off-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
Change-Id: I1b40e24faf8d85f32839a3d44fd936ca7ee7e09f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58572
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
In-band controls work to enable/disable the WWAN module. Hence
WWAN_DISABLE_GPIO is not critical and can be marked as not connected.
BUG=b:188415287
TEST=Build and boot to OS in Guybrush. Ensure that the WWAN module is
enumerated on boot and reboot.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: I7fefba3de9c749971911b21ed4712e950cef5a6a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58599
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Rob Barnes <robbarnes@google.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
|
On all upcoming variants and board versions of existing variants,
SD_AUX_RESET_L signal moves from GPIO_69 to GPIO_5. This means all
boards except:
* All board versions of Guybrush
* Nipperkin Board Version 1.
Also in Nipperkin, LCD_PRIVACY_PCH signal moves from GPIO_5 to GPIO_18.
Configure the gpios accordingly in baseboard, guybrush and nipperkin
variants accordingly. Also update the DXIO port descriptor for SD PCIe
engine with the corresponding AUX reset GPIO.
BUG=b:202992077
TEST=Build and boot to OS in Guybrush & Nipperkin. Ensure that the SD
Controller and SD Card are enumerated fine. Ensure that the enumeration
is successful after a suspend/resume cycle.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: If28810747e6b4eaae2a693a98e1adc830f80bcf6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58598
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Rob Barnes <robbarnes@google.com>
|
|
The baseboard enables PCIe RPs 6, 8 and 9, but kano doesn't use
these. Having them enabled will occasionally cause suspend
attempts to fail, therefore disable them in the overridetree.
BUG=b:203389490 b:192370253
TEST=FW_NAME=kano emerge-brya coreboot and verify it builds
without error.
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: Ie2b82cff6d910c961eeb56704dcbae2bdc2a8c53
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58566
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: YH Lin <yueherngl@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
On Guybrush, pen is stuffed and GPIO_5 is used to enable Pen power. On
Nipperkin board version 1, pen is not stuffed and instead the GPIO is
used to control LCD Privacy settings. On upcoming Nipperkin board
versions and other variants, GPIO_5 is not used. Configure GPIO_5
accordingly.
BUG=b:202992077
TEST=Build and boot to OS in Guybrush. Ensure that the configuration is
retained on existing boards.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: I2aa2f16282b91f157701212ee27ddd2e89918767
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58597
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Rob Barnes <robbarnes@google.com>
|
|
The `SMBIOS_PROVIDED_BY_MOBO` Kconfig option is already selected through
the `SECUNET_DMI` option. So, there's no need to select both of them.
Change-Id: I784df87893043a011906af8808aff27d636c7626
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58625
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
FMAP was developed with assumption about endianness of the target machine.
This broke the parsing of the structure on big endian architectures. This
patch converts the endianness of the fields where applicable.
Signed-off-by: Krystian Hebel <krystian.hebel@3mdeb.com>
Change-Id: I8784ac29101531db757249496315f43e4008de4f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55038
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Add new memory parts in memory_parts_used.txt and generate SPD id for
these parts:
Hynix H54G46CYRBX267
Samsung K4U6E3S4AB-MGCL
BUG=b:204014463
TEST=run part_id_gen to generate SPD id
Signed-off-by: Wisley Chen <wisley.chen@quanta.corp-partner.google.com>
Change-Id: I43df98d84c6a274d6f96c8818ce6acff9337d8d3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58565
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Add new memory parts in memory_parts_used.txt and generate SPD id for
these parts:
Micron MT53E512M32D1NP-046 WT:B
Hynix H54G46CYRBX267
Samsung K4U6E3S4AB-MGCL
BUG=b:204015944
TEST=run part_id_gen to generate SPD id
Change-Id: Icf2f7352a4bd6a58e3e7abdcaac823b863984732
Signed-off-by: Wisley Chen <wisley.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58562
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Correct GPIO GPP_R6 and GPP_R7 setting to NF2 (DMIC_CLK1 and DMIC_DATA1).
BUG=b:197385770
TEST=emerge-brask coreboot and verify it builds without error.
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: Ia3813306f8c7b69fe5cf0e188c55256b68d329ab
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58578
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
This patch set disables the external voltage rails since kano
board doesn't have V1p05 and Vnn bypass rails implemented.
BUG=b:192370253
TEST=FW_NAME=kano emerge-brya coreboot and verify it builds
without error.
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: Ia1f3f4b2ada0154c716aedd521d4151124411ba3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58569
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
To prevent unexpected alert from eSPI to SOC, configure this alert pin
to in-band.
BUG=b:199458949,b:203446084
BRANCH=guybrush
TEST=emerge-guybrush coreboot chromeos-bootimage
Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com>
Change-Id: I18d38fe504bd9f2069b9977d5a35729691f672d1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57976
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Rob Barnes <robbarnes@google.com>
|
|
Follow up the G2 spec: G7500_Datasheet_Ver.1.2
BUG=b:203607764,b:202090378
BRANCH=guybrush
TEST=emerge-guybrush coreboot chromeos-bootimage
TS is functional
Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com>
Change-Id: I98dd3095043ab537d91e81b84944779240b203ec
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58564
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Rob Barnes <robbarnes@google.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
This change adds sub-regions to SI_ME in chromeos.fmd. These are
required to support stitching of CSE components.
BUG=b:189177538
Change-Id: Ife48aafcec43555175aad44f8b6307beeaea9184
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58592
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Selecting CPU_X86_CACHE_HELPER only added the x86_enable_cache wrapper
function around enable_cache which additionally wrote a POST code to
port 0x80 and printed a message to the console. This function was only
called during multi-processor initialization in ramstage via the init
function pointer in the CPU's device operations struct and was run on
all cores, so the message on the console was printed once per CPU core.
This patch replaces all x86_enable_cache calls by calls to enable_cache
and removes the wrapper function and the Kconfig symbol
CPU_X86_CACHE_HELPER which was used to only add this when the
corresponding CPUs used the x86_enable_cache wrapper function.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Suggested-by: Angel Pons <th3fanbus@gmail.com>
Change-Id: I5866b6bf014821ff9e3a48052a5eaf69319b003a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58579
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Since all x86 CPUs in tree have MTRR support, there is no need to guard
the DISPLAY_MTRRS option with HAVE_DISPLAY_MTRRS. Also all x86 CPUs/SoCs
have a display_mtrrs call at least somewhere in their code, so selecting
the DISPLAY_MTRRS option will always have an effect. All SoCs that don't
select RESET_VECTOR_IN_RAM have the postcar stage where it gets called.
The two AMD SoCs that select RESET_VECTOR_IN_RAM use the FSP2 driver
which contains plenty of display_mtrrs calls.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I2894689ce58e7404d9d5a894f3c288bc4016ea19
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51575
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
All x86 CPUs in the coreboot tree have a local APIC, so the
corresponding code can be unconditionally included in the build.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ifc354fb386977b0fca4caa72c03aa77a20bc348e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58551
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
The Intel Quark SoC does have a LAPIC on its x86 CPU core, so we should
select CPU_X86_LAPIC. This will additionally include the Makefile from
cpu/x86/lapic. Since none of AP_IN_SIPI_WAIT, LEGACY_SMP_INIT and
UDELAY_LAPIC gets selected, only the boot_cpu.c and lapic.c targets will
be added to the build. Since SMP isn't set, adding the boot_cpu.c target
won't change the resulting binary of a timeless build, since the only
function inside will be removed by the compiler's pre-processor in the
!SMP case. So the only thing that will change the resulting binary is
the addition of the lapic.c target. From this target only the function
cpu_get_lapic_addr will be used which overrides the weak implementation
in acpi/acpi.c. The call in arch/x86/mpspec.c can be ignored, since
GENERATE_MP_TABLE isn't selected. So this change will result in the
LAPIC address in the MADT being changed from 0 to to LAPIC_DEFAULT_BASE.
Since the documentation of the Quark SoC mentions that it has a LAPIC on
its one x86 core, this should work.
TEST=None
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I2f163bd608f0548abb0e8de90843d2a796b8ef6c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58550
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Compatible headphone codec "Realtek ALC5682I-VD" and "ALC5682I-VS"
BUG=b:197694580
BRANCH=dedede
TEST=ALC5682I-VD or VS audio codec can work normally
Signed-off-by: Yongkun Yu <yuyongkun@huaqin.corp-partner.google.com>
Change-Id: I422f206b8f1f3705a65808041f1a1544c461b431
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58449
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Wentao Qin <qinwentao@huaqin.corp-partner.google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Half of the AMD PCI device ID definitions were below the ATI vendor ID,
so move those below the AMD PCI vendor ID definition. The entries are
kept in the order they were before and added before the existing AMD
device ID definitions below the AMD vendor ID definition.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I34ffdc49884737541b8653bebf023a68050375d6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58582
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
The definitions isn't used in either spelling.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Id6faea2b9c89f0bd3c164a6dc76fac5ea712d313
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58581
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
|
Initialize the pad_cfg_lock_offset field for the various gpio
pad_community structures in the adl_communities.
BUG=b:201430600
TEST='emerge-brya coreboot' and verify it compiles successfully.
Change-Id: I2cd3e43a84b0140bb2aeae5de1e299db714d419b
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58350
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Update api name and comments to be more generic as spi destination
id is not DMI specific.
Update api name as soc_get_spi_psf_destination_id and comments.
And move PSF definition from pcr_ids.h as it's not pcr id.
Signed-off-by: Wonkyu Kim <wonkyu.kim@intel.com>
Change-Id: Ie338d05649d23bddae5355dc6ce8440dfb183073
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58433
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Jamie Ryu <jamie.m.ryu@intel.com>
|
|
Since all multi-core x86 CPUs need to have LAPICs, this option should be
selected for soc/example/min86.
TEST=The example/min86 mainboard still builds.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I5aa6e850f0b4dca27309385ba889b04335fe4f0c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58549
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
With using a Kconfig option to add the x86 LAPIC support code to the
build, there's no need for adding the corresponding directory to subdirs
in the CPU/SoC Makefile. Comparing which CPU/SoC Makefiles added
(cpu/)x86/mtrr and (cpu/)x86/lapic before this and the corresponding
MTRR code selection patch and having verified that all platforms
added the MTRR code on that patch shows that soc/example/min86 and
soc/intel/quark are the only platforms that don't end up selecting the
LAPIC code. So for now the default value of CPU_X86_LAPIC is chosen as y
which gets overridden to n in the Kconfig of the two SoCs mentioned
above.
Change-Id: I6f683ea7ba92c91117017ebc6ad063ec54902b0a
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44228
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
The code for these CPU models isn't present in coreboot. These lines
have been commented-out since they where added, so drop them.
Change-Id: I8fc53fea4225217bc5bb70d839c280ebb64fd3a6
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44218
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
Move the selection of CPU_X86_CACHE_HELPER to the Kconfig file of the
CPU models which call the x86_enable_cache function that gets added to
the build by selecting this option.
Change-Id: Ie75682f5d20a79fc2f3aab9b8a2c3ccf79d1ad5c
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44227
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
There's no need to have an overridetree with a single board variant.
TEST=Compare static.c and observe only device order has changed.
Change-Id: I2097e247c27d5d0c5479cb533b477cd490a4c827
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58367
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Move per-port PCIe settings inside the corresponding PCIe root port
device. Also, remove several unnecessary and/or redundant comments.
Tested with BUILD_TIMELESS=1, Prodrive Hermes remains identical.
Change-Id: I3f64d56b3b2c592194b18ae7b7c63ef41a1e060f
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58325
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
There's no need for relative paths with Kconfig options.
Change-Id: Ib9b9b29a158c34a30480aaabf6d0b23819d28427
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44226
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
Some CPUs don't use the ramstage-only x86_enable_cache helper function
to call enable_cache with some added port 0x80 and console output.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Suggested-by: Angel Pons <th3fanbus@gmail.com>
Change-Id: Ia44c7b150cd12d76e463903966f67d86750cbdd9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58548
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
No SoC uses the ramstage-only x86_enable_cache helper function to call
enable_cache with some added port 0x80 and console output.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Suggested-by: Angel Pons <th3fanbus@gmail.com>
Change-Id: I7c5039e1341fd4089078ad7ffb2fe6584a94045c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58547
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
This change is required as part of HECI Interface initialization in order
to put the host and CSE into a known good state for communication. Please
refer ME BIOS specification for more details. The change adds HECI
interface reset flow in the CSE driver. It enables coreboot to send HECI
commands before DRAM Init.
BUG=b:175516533
TEST=Run 50 cold reset cycles on Brya
Signed-off-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Change-Id: Ie078beaa33c6a35ae8f5f460d4354766aa710fba
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55363
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
MBP Hob is being generated by FSP after getting data from ME.
coreboot does not consume this HOB and FSP provides an option
for bootloader to skip generation of MBP HOB. This will help in
saving ~14 ms of boot time.
Here is the data from Brya P1 Board:
Before: 955 returning from FspSiliconInit 879,432 (99,156)
After: 955 returning from FspSiliconInit 1,177,513 (84,506)
BUG=b:188577893
BRANCH=None
TEST=No functional impact on Brya system and boot time is reduced
with this patch.
Change-Id: Ibb64e4d0f4ae7212defb6704b05a78e754f75cd7
Signed-off-by: MAULIK V VAGHELA <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58289
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
turn off WLAN ASPM L1.1/L1.2 as a short-term w/a for WLAN AP probe failure.
BUG=b:198258604
BRANCH=guybrush
TEST=emerge-guybrush coreboot chromeos-bootimage
AP is able to be probed by wlan module
Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com>
Change-Id: Ic7be523626b0ff6e4b1c66ba6af13b15061ef4cb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58417
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
AOP firmware support from sc7280.
BUG=b:182963902
TEST=Validated on qualcomm sc7280 development board
Signed-off-by: Ravi Kumar Bokka <rbokka@codeaurora.org>
Change-Id: Ib7027cdf78a9cdcccc8cfff7eef3cc540fb4093e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58371
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shelley Chen <shchen@google.com>
|
|
Move AOP firmware support from qualcomm/sc7180 into qualcomm/common
BUG=b:182963902
TEST=Validated on qualcomm sc7180 development board
Change-Id: I90b0f48e15df390970e027bff2065b7a89b14cec
Signed-off-by: Ravi Kumar Bokka <rbokka@codeaurora.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49767
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shelley Chen <shchen@google.com>
|
|
BUG=b:182963902
TEST=Validated on qualcomm sc7280 development board
Signed-off-by: Ravi Kumar Bokka <rbokka@codeaurora.org>
Change-Id: I62044f6fcb301c0ca35c42598f998913f9b94b95
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58528
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shelley Chen <shchen@google.com>
|
|
Use the verstage_x86 class for the spi_dma.c target instead of using the
verstage class and guarding it with !VBOOT_STARTS_BEFORE_BOOTBLOCK.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I9b8cafd1ef17df8c485f6594bc0928cea88e436b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58544
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Since cpu/x86/Makefile.inc already adds the pae sub-directory, there is
no need to include it in the Makefile of a CPU or SoC, so remove it from
those Makefiles.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I78368f7eb880fb64f511a2fa8c8acde222d0dca3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58546
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
All x86-based CPUs and SoCs in the coreboot tree end up including the
Makefile in cpu/x86/mtrr, so include this directly in the Makefile in
cpu/x86 to add it for all x86 CPUs/SoCs. In the unlikely case that a new
x86 CPU/SoC will be added, a CPU_X86_MTRR Kconfig option that is
selected be default could be added and the new CPU/SoC without MTRR
support can override this option that then will be used in the Makefile
to guard adding the Makefile from the cpu/x86/mtrr sub-directory.
In cpu/intel all models except model 2065X and 206AX are selcted by a
socket and rely on the socket's Makefile.inc to add x86/mtrr to the
subdirs, so those models don't add x86/mtrr themselves. The Intel
Broadwell SoC selects CPU_INTEL_HASWELL and which added x86/mtrr to the
subdirs. The Intel Xeon SP SoC directory contains two sub-folders for
different versions or generations which both add x86/mtrr to the subdirs
in their Makefiles.
Change-Id: I743eaac99a85a5c712241ba48a320243c5a51f76
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44230
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
This patch fixes regression introduced by commit bee4bb5f0
(soc/intel/common/cse: Late sending EOP msg if !HECI_DISABLE_USING_SMM)
FAFT test case fail when doing `firmware_DevMode` test.
If CSE is already hidden then accessing CSE registers would be wrong
and will receive junk, hence, return as CSE is already disabled.
BUG=b:203061531
TEST=Brya system can boot to OS with recovery mode.
Change-Id: I2046eb19716c397a066c2c41e1b027a256bd6cf9
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58513
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Use %u instead of %d for printing unsigned variables.
Change-Id: I0f4bf7b80dfbde0802af8ad96fd553cb75d60e6e
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58245
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
There are manual timeout-loops which use a fixed value and udelay().
In all cases there is a debug printk() inside this loop which, when
enabled, takes way longer than the counted microsecond delay. This
leads to the result that e.g. a 1 second delay takes nearly an eternity
if the debug messages are enabled due to the longer function execution
time.
This patch uses the stopwatch scheme for the timeout-loops which still
makes sure that the timeout period is maintained while it takes longer
function calls like printk() into account. In order to keep the minimum
delay between two register accesses on the TPM keep the udelay(1)-call.
TEST=Enable TPM debug messages on a board where the TPM hits a timeout
by failure and make sure that the debug messages occur in the log
just in the timeout period. It still works as expected if the debug
messages are disabled.
Change-Id: I8fd261c9d60a9a60509c847dbc4983bc05f41d48
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58240
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Enable CnviBtAudioOffload UPD
BUG=b:199180746
TEST=emerge-byra coreboot
Signed-off-by: Mac Chiang <mac.chiang@intel.com>
Change-Id: Ic507b1d0f7c2f38de8d24247cd677b897a7463f1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58514
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
The commit 04a40379b has a wrongly written variable, which sets an
IOAPIC register to a wrong value and makes the Linux kernel unable to
boot.
Tested on HP EliteBook 2760p, the kernel boots after this patch.
Change-Id: Ifda7bb61a431dbf9c2df2f738aa806dd6d8097b8
Signed-off-by: Iru Cai <mytbk920423@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58558
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
After adding code to handle the case of missing the link/bus on the CPU
cluster device in mp_cpu_bus_init, there's no need to have the LAPIC
device in the devicetree any more.
TEST=Mandolin still boots successfully.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Icfc4fb61b373129f3bf4f4de09c38076a8f66733
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58510
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
After adding the functionality to add a bus/link on the CPU cluster
device in mp_cpu_bus_init if it is missing due to no LAPIC device being
present in the devicetree below the CPU cluster device, we can use
mp_cpu_bus_init as init function in cpu_bus_ops and implement
mp_init_cpus.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I76aebeca1b3227cfd310b6c45f506c042b35ae04
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58509
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
When a chipset or mainboard devicetree doesn't have any LAPIC devices in
its CPU cluster, not only the LAPIC device, but also the link/bus
between the CPU cluster device and the LAPIC devices will be missing and
the CPU cluster's dev->link_list will be NULL. This patch handles this
case in the common code like
commit 3c0ecd57c174b7391c66d22406effe18ce570cac (soc/intel/common/cpu:
Handle non-zero BSP APIC ID in init_cpus) and
commit ba936ce5db819d5ecb34e83a998b2390ecbdc4b9 (soc/intel/denverton_ns:
Ensure CPU device has a valid link) already did in the common Intel SoC
and the Denverton code. With this change all CPUs and SoC that use the
common mp_cpu_bus_init as init function in the CPU cluster's device
operations struct won't require having at least one LAPIC device in the
chipset or mainboard device tree.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ib0d85de5cafb6390b8fbd512186899d6a815e972
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58508
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Since PSE devices could be initialized as either host owned
(PCI devices) or PSE owned (will be hidden from coreboot and
only visible to PSE interface), add all PSE devices in PCI
list header file for future usage.
Signed-off-by: Lean Sheng Tan <lean.sheng.tan@intel.com>
Change-Id: Iaa40cdcb021d05e50504dd85f94e9c021e284d00
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58466
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|