| Age | Commit message (Collapse) | Author |
|---|
|
From comments of CB:65875, we replace *_vol to *_voltage.
s/mainboard_set_regulator_vol/mainboard_set_regulator_voltage/
s/mainboard_get_regulator_vol/mainboard_get_regulator_voltage/
TEST=build pass
BUG=b:233720142
Signed-off-by: Bo-Chen Chen <rex-bc.chen@mediatek.com>
Change-Id: Iadf0408e8914d6e32915464f93979978c4634eaf
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65994
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
For MT8188, we need to enable and adjust VMCH and VMC to support SD
cards. Therefore, we add VPA and VSIM1 voltage adjustment APIs.
TEST=measure 3.0V in VMCH and VMC.
BUG=b:236331724
Signed-off-by: Hui Liu <hui.liu@mediatek.corp-partner.google.com>
Change-Id: I03938f9ef17a0bdd615bcbbfc7b59fa5acb8fbfb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65874
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
TEST=build pass
BUG=b:233720142
Signed-off-by: Bo-Chen Chen <rex-bc.chen@mediatek.com>
Change-Id: I71cc69c74dd618f441140790af351095ead3f6f9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65759
Reviewed-by: Yidi Lin <yidilin@chromium.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add PMIF, SPI, SPMI and PMIC init code.
These PMIC settings are used by MediaTek internally. We can find these
registers in "MT6365_PMIC_Data_Sheet_V1.4.pdf" and
"MT6315 datasheet v1.3.pdf". The setting values are provided by MeidaTek
designers.
TEST=build pass
BUG=b:233720142
Signed-off-by: Hui Liu <hui.liu@mediatek.corp-partner.google.com>
Change-Id: I05a51894b130a59c28d957b64d6401c8bb9cee91
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65758
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
We will use the same drivers for checking ulposc in MT8188, so we add a
new function pmif_ulposc_check() to common.
TEST=build pass
BUG=b:233720142
Signed-off-by: Bo-Chen Chen <rex-bc.chen@mediatek.com>
Change-Id: I40136eaeb2c08a97cd65bfb8a81f2f24739d4d51
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65841
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Ti50 hasn't implemented version reading yet. To avoid the confusing
error message
Did not recognize Cr50 version format
enable TI50_FIRMWARE_VERSION_NOT_SUPPORTED to make clear that this
feature is not supported.
BUG=b:234533588
TEST=emerge-corsola coreboot
BRANCH=none
Change-Id: I18dd4b5bc05c2af06627275968e49aba048ba05e
Signed-off-by: Yu-Ping Wu <yupingso@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65839
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yidi Lin <yidilin@chromium.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
|
|
This patch moves the early GPIO programming from
`bootblock_mainboard_init` to `bootblock_mainboard_early_init`.
It will help to get the early debug prints as below.
TEST=Without this CL the initial report platform information
was missing as below:
[DEBUG] VBOOT: Loading verstage.
[DEBUG] FMAP: Found "FLASH" version 1.1 at 0x1c04000.
[DEBUG] FMAP: base = 0xfe000000 size = 0x2000000 #areas = 33
[DEBUG] FMAP: area COREBOOT found @ 1c09000 (4157440 bytes)
[INFO ] CBFS: mcache @0xfef84a00 built for 18 files, used 0x414
of 0x2000 bytes
[INFO ] CBFS: Found 'fallback/verstage' @0x24d240 size 0x133d0 in
mcache @0xfef84d50
With this CL the complete bootblock serial msg is coming.
[NOTE ] coreboot-.mtl.po.ww29.5 Fri Jul 15 21:47:36 UTC 2022
bootblock starting (log level: 8)...
[DEBUG] CPU: Genuine Intel(R) 0000 @
[DEBUG] CPU: ID a06a0, MeteorLake A0, ucode: f0270108
[DEBUG] CPU: AES supported, TXT supported, VT supported
[DEBUG] MCH: device id 7d14 (rev 00) is MeteorLake P
[DEBUG] PCH: device id 7e01 (rev 00) is MeteorLake SOC
[DEBUG] IGD: device id 7d55 (rev 00) is MeteorLake-P GT2
[DEBUG] VBOOT: Loading verstage.
[DEBUG] FMAP: Found "FLASH" version 1.1 at 0x1c04000.
[DEBUG] FMAP: base = 0xfe000000 size = 0x2000000 #areas = 33
[DEBUG] FMAP: area COREBOOT found @ 1c09000 (4157440 bytes)
[INFO ] CBFS: mcache @0xfef84a00 built for 18 files, used 0x414
of 0x2000 bytes
[INFO ] CBFS: Found 'fallback/verstage' @0x24d240 size 0x133d0
in mcache @0xfef84d50
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I3e092cd749359e54fe518de21671275af4b03062
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65986
Reviewed-by: Tarun Tuli <taruntuli@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
|
|
The generic wifi driver currently contains a lot of intel specific
functionality that results in it not working properly on AMD platforms.
This commit updates the base device tree to use the generic PCIe driver
instead.
BUG=none
TEST=Ran on nipperkin device, dumped SSDT and checked wakeup sources
Change-Id: Iafbc68c1ae33ccc260889f0b39fc5fe8a59d7aca
Signed-off-by: Robert Zieba <robertzieba@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65990
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The generic wifi driver currently contains a lot of intel-specific
functionality that interferes with enabling wake-on-lan. This commit
changes the device tree to use the generic PCIe driver which better
supports this functionality.
BUG=b:237682766
TEST=Booted on skyrim device and verified that wake on LAN works
Signed-off-by: Robert Zieba <robertzieba@google.com>
Change-Id: I5d15d33fd0a152eb3bf2bfe78e802483a701e750
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65800
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This commit adds support for `_PRW` in this driver.
BUG=b:237682766
TEST=Built and booted on Skyrim device, dumped SSDT
Change-Id: Ife4ba48994cbf993bc88df8354576336438e4258
Signed-off-by: Robert Zieba <robertzieba@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65799
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This commit adds code to allow the driver to use an ACPI device name
that is set in the device tree.
BUG=b:237682766
TEST=Boot changes on Skyrim device, dumped SSDT
Signed-off-by: Robert Zieba <robertzieba@google.com>
Change-Id: Ie40a335e35b8ac83658e67d7cfba0750dd4784ad
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65798
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This removes unneeded and unused functionality in the driver as part of
an effort to make the driver more generic and useful. The things that
have been removed are: `DmaProperty` and its associated `is_untrusted`
config, `_DSD` generation, and the companion device functionality. This
driver isn't currently used anywhere so there won't be any issues from
removing the above functionality.
BUG=b:237682766
TEST=Built and booted coreboot on Skyrim device
Change-Id: I0abd9148ab66ea9426069102ecc8c2fa77fea98e
Signed-off-by: Robert Zieba <robertzieba@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65797
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The SPI_RESTRICTED_CMD register is not a PCI configuration register. It
is memory mapped from the SPI bar.
Verified against PPR 55570 rev 3.16, PPR 56569 rev 3.03, and PPR 57243
rev 1.50
TEST=Compile tested only
Change-Id: I7c88aaea9ddac200644bb368be3bd4e9be47fd7b
Signed-off-by: Fred Reitberger <reitbergerfred@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63305
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Adjust I2C speed for codec, TPM, touchpad.
BUG=b:237691531
TEST=Built and verified adjusted I2C speed < 400KHz
Change-Id: I203d137d61019235ddf38ef74607427db2a7e975
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65957
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
This makes inspection of linker scripts in the build dir a little
easier.
Change-Id: I509faa4cee2c9f066f4e20f6038349e1165a619a
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/64362
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Prepare platforms for linking romstage code in the bootblock.
Change-Id: Ic20799b4d6e3f62cd05791a2bd275000a12cc83c
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63420
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Switch x86 uart output from EC to LPSS.
Signed-off-by: Lean Sheng Tan <sheng.tan@9elements.com>
Change-Id: I2756d139a72185ba6a5c6d1079d770ce33afdf71
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65985
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=b:238571507
BRANCH=None
TEST=emerge-herobrine coreboot
Change-Id: Ie596e5c4b72de84d16571043db4291bbd0825c78
Signed-off-by: Sheng-Liang Pan <sheng-liang.pan@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65947
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shelley Chen <shchen@google.com>
Reviewed-by: Bob Moragues <moragues@chromium.org>
|
|
PSP expects PSP L2 directory address relative to the start of the SPI
ROM. Also PSP does not expect BIOS L2 directory address since it is an
entry in PSP L2 directory. Update the configuration such that PSP
verstage passes the right address to PSP.
BUG=b:217414563
TEST=Build Skyrim BIOS image. Ensure that PSP verstage passes the
address as expected by PSP.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: I8dc3aa4cb401d16a68da446f83eb9e68ee290fea
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65866
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
On SoCs where PSP use A/B recovery layout, PSP expects PSP L2 directory
address relative to the start of the SPI ROM. Unfortunately there is
nothing in the EFS2 header to help identify such SoCs. Hence add a
config item to statically identify such SoCs.
Also when PSP uses A/B recovery layout, BIOS L2 directory is an entry in
the PSP L2 directory. Hence the address of BIOS L2 directory is not part
of EFS2 header. Thankfully PSP is able to identify the BIOS L2 directory
itself and does not expect PSP verstage to pass the address. Modify PSP
verstage to handle these updates.
BUG=b:217414563
TEST=Build Skyrim BIOS image. Ensure that PSP verstage returned the PSP
L2 directory as expected.
Change-Id: I2f856a62055c80b8e2db91c983832611a5f0389c
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65865
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
PSP supports mapping FCH UART and verstage logs are visible in console.
Hence pre-bootblock cbmem contents do not have to be dumped to console.
BUG=b:238937687
TEST=Build Skyrim BIOS image. Ensure that PSP verstage logs in CBMEM are
not dumped to console again during bootblock.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: I8336e372b894d8b2f9bbfb21ab15a78527dcc4c4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65863
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Skyrim uses second SPI pads for ESPI. Switch to it initialize ESPI in
verstage.
BUG=b:217414563
TEST=Build Skyrim BIOS image. Ensure that ESPI init is successful in PSP
verstage.
Change-Id: I6e3462e95c50d256b6c159ae1d854dd69a538bb0
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65862
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Martin L Roth <gaumless@tutanota.com>
|
|
SoC FW ID needs to be populated at offset 0x58 and 0x59 in the PSP
header.
BUG=b:217414563
TEST=Build Skyrim BIOS image and ensure that PSP verstage is getting
loaded.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: Ibe7b26aea0567e5337ee3e6e9447aa3944c55f5b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65860
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jon Murphy <jpmurphy@google.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Change-Id: Ib852d0b2cf4d3cbdf7475bd5493bf2e585a5894a
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/64899
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Change-Id: I187c2482dd82c6c6d1fe1cbda71710ae1a2f54ad
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/64890
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Now that the speed is limited to 5500 Mbps for all memory parts used in
Skyrim, regenerate the part IDs. Remove any custom generated part IDs
and the associated SPDs.
BUG=b:238074863
TEST=Build and boot to OS in Skyrim.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: I6d8326208580a971e781887a7ec83355bb085c7f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65709
Reviewed-by: Robert Zieba <robertzieba@google.com>
Reviewed-by: Jon Murphy <jpmurphy@google.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add the CSE, General Status and Miscellaneous registers and
print information from them accordingly. All values were taken
from Intel document number 571993.
Tested on the StarLite Mk III and the correct values are
shown:
[DEBUG] CSE: Working State : 2
[DEBUG] CSE: Manufacturing Mode : NO
[DEBUG] CSE: Operation State : 1
[DEBUG] CSE: FW Init Complete : NO
[DEBUG] CSE: Error Code : 3
[DEBUG] CSE: Operation Mode : 0
[DEBUG] CSE: FPF status : unknown
Please note, the values shown are in an error state.
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: I1a5548132dadbb188a33a7ae30a0a1fa144d130f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65981
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
When override "max_dram_speed_mts", set the DdrSpeedControl to manual.
(0:Auto, 1:Manual)
BUG=b:229549930
BRANCH=none
TEST=build coreboot without error
Signed-off-by: Franklin Lin <franklin_lin@wistron.corp-partner.google.com>
Change-Id: Iffbbee8082fb1a41e0ed1db3f4ea9ec4709c9ce7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65877
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The agah EC code includes a driver to keep track of the current D Notify
level that the GPU should be at. When it changes, it will send a host
event to the ACPI FW, which will then pass that Notify on to the kernel
driver. This patch adds support for that feature, which is described in
the Nvidia Software Design Guide.
BUG=b:229405562
TEST=add Printf() calls to the ACPI, and work through the various
scenarios on the EC that will cause D Notify levels to change; this
will cause the Printfs() to show up in the kernel log.
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I5cd8bd7d177ea10a165613ed0726a6d6fd86c226
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65486
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Robert Zieba <robertzieba@google.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Guard gpmr_lockdown_cfg with SOC_INTEL_COMMON_BLOCK_GPMR
so it doesn't run on platforms that don't select this.
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: Iab5bbd399c3a654dcb95eaa8fce683a50c7322f2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65227
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
|
|
In preparation to add a third option, have "Client" platforms select a
dedicated Kconfig option instead of the common "_BASE" option. Rewrite
the help texts to clarify what "Client" and "Server" mean, because the
terms refer to the type of silicon and not to the market segment. Some
uniprocessor (single-socket) servers are actually client platforms and
there are some multi-socket workstations based on a server platform.
Change-Id: I646729d709f60ca2b5e74df18c2b4e52f9b10e6b
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65951
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sean Rhodes <sean@starlabs.systems>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
|
|
The headers added are generated as per FSP v3257_00_40.
In the future, when Alder Lake and Raptor Lake fsp align, Raptor Lake
fsp headers can be deleted and Raptor Lake soc will also use headers
from alderlake/ folder.
BUG=b:238791453
BRANCH=firmware-brya-14505.B
TEST=none
Signed-off-by: Bora Guvendik <bora.guvendik@intel.com>
Change-Id: If8fd6700f0afed7e2bd5d73a95407dbfd3e88abd
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65803
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
BUG=b:236175568
TEST=Build and test on MB, system can boot to OS.
Signed-off-by: Tyler Wang <tyler.wang@quanta.corp-partner.google.com>
Change-Id: I779355dcc69eed08703bcb8bb943dcfeeb1fdea1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65945
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
For brya/skolas, I2C1 is cr50, and I2C3 is Touchscreen
BUG=None
BRANCH=firmware-brya-14505.B
TEST=None
Signed-off-by: Eran Mitrani <mitrani@google.com>
Change-Id: I4058e0f33b2bb6227a0af92941ed4e2eb56ba542
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65792
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
Most of these changes are suggested by clang-format(13.0-54) tool on
Debian testing.
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Change-Id: Ie4fe0e872e94f38079945970848fefd153ab7cb5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/64782
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <gaumless@tutanota.com>
|
|
This change adds memory part used by variant beadrix to
mem_part_used.txt and generates DRAM ID allocated to the part.
BUG=b:236750116
BRANCH=None
TEST=Run part_id_gen to generate SPD id
Signed-off-by: Teddy Shih <teddyshih@ami.corp-partner.google.com>
Change-Id: I3f29609d9fe5143b0bfe4b78279d0780cd7e5097
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65306
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Super Ni <super.ni@intel.corp-partner.google.com>
Reviewed-by: Henry Sun <henrysun@google.com>
Reviewed-by: Ivan Chen <yulunchen@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Call heci_init to initialise all Heci devices and bring them to d0.
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: Id2865b649331846fc119da7c4be56cc1fed56b8b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/64860
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
This patch tries to simplify the baseboard/variant GPIO programming
starting with Google/Rex. The idea is to let each variant maintain
its own complete GPIO PAD configuration table instead of having a
back-and-forth call between baseboard and variants.
With this patch coreboot performing GPIO programming is now much
simpler where the common code block calls into respective variants
and gets the gpio table prior to the pad configuration.
BUG=b:238165977 (Simplify baseboard/variant GPIO programming starting
with Google/Rex)
TEST=Able to build and boot the Google/Rex board.
AP firmware log with DEBUG_GPIO kconfig lists the early GPIOs being
configured from the `rex0` variant.
gpio_padcfg [0xd3, 08] DW0 [0x44000300 : 0x40000400 : 0x40000400]
gpio_padcfg [0xd3, 08] DW1 [0x00000020 : 0x00000000 : 0x00000020]
gpio_padcfg [0xd3, 08] DW2 [0x00000000 : 0x00000000 : 0x00000000]
gpio_padcfg [0xd3, 08] DW3 [0x00000000 : 0x00000000 : 0x00000000]
gpio_padcfg [0xd3, 09] DW0 [0x44000300 : 0x40000400 : 0x40000400]
gpio_padcfg [0xd3, 09] DW1 [0x00000021 : 0x00000000 : 0x00000021]
gpio_padcfg [0xd3, 09] DW2 [0x00000000 : 0x00000000 : 0x00000000]
gpio_padcfg [0xd3, 09] DW3 [0x00000000 : 0x00000000 : 0x00000000]
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I8ec5c6991ec90a3884464e7f15f33327bfe4839a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65674
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Set USB3 port2 tx_de_emp 0x2B by "11th Gen Intel Core Processors for
IoT Platforms EDS Addendum_rev1.6" then fix the USB3 port2 Gen2 RX
failed.
BUG=b:236661824
TEST=emerge-brask coreboot and check USB3 port2 RX pass
Signed-off-by: Raihow Shi <raihow_shi@wistron.corp-partner.google.com>
Change-Id: I7a5add20f055a8d871c6b4f33734fb8a397cba76
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65848
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This allows the mainboard code to change FSP-M parameters depending on
parameters that are only known at run time and not at build time.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I3e0e196a5d861acd7635c59db44ecf1970b73ce2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65855
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
|
|
Add support for hardware watchdog event logging
BUG=b:221393157
TEST=Validated on qualcomm sc7280 development board by manually
triggering watchdog event and event was logged at next bootup.
Signed-off-by: Kshitiz Godara <quic_kgodara@quicinc.com>
Change-Id: I94971ab583f49c8a5ac232833215dbdad3a4d272
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65528
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add watchdog file compilation and watchdog space memory for sc7280.
BUG=b:221393157
TEST=None
Signed-off-by: Kshitiz Godara <quic_kgodara@quicinc.com>
Change-Id: I6a5c4e55964aa8b4de5a641ca162355591c38fc1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65559
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shelley Chen <shchen@google.com>
|
|
Ported back from commit ceaf9d116949da68aa9c ("soc/intel/alderlake:
Allow possible options for MP Init")
This patch creates choice that lists all possible options to perform
MP Init as below for Intel Meteor Lake platform:
1. MTL_USE_FSP_MP_INIT: Allow coreboot to bring APs from reset and FSP
runs feature programming based and selects MP_SERVICES_PPI_V2 config.
2. MTL_USE_COREBOOT_MP_INIT: Allow coreboot to perform MP Init (both AP
init and feature programming) using native implementation.
Additionally, selects required RELOAD_MICROCODE_PATCH when coreboot
is expected to run MP Init.
Refactor SoC code to allow required FSP UPD override based on
selected MP Init option.
Additionally, added `FIXME` comment to ensure Intel MTL FSP can bring
back SkipMpInit UPD in MTL to let coreboot override this UPD and ensure
independent MP Init flow.
BUG=b:219053812
TEST=Able to build google/rex.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: Ic917e4e03e24d73190cfc72c6ed8e59af427bedf
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65743
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch enables coreboot doing Multiprocessor Initialization (MP)
for Meteor Lake CPU using the native coreboot drivers and passes the
MP PPI data structure to let FSP to perform CPU feature programming
(anything that is restricted) as part of FSP-S.
Additionally, modify the kconfig inclusion order alphabetically.
BUG=b:219061518, b:219053812
TEST=Able to bring all APs from reset by coreboot and successfully
able to perform all CPU feature programming using MP PPI services.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: Ic2781ee0b39e42aa579b72d3d4ee6586d5a89a02
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65742
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch ensures Intel Meteor Lake can enable the X2APIC feature.
While debugging Intel Meteor Lake (MTL) based platforms it seems like
enabling `DEFAULT_X2APIC` runs into a hang while coreboot tries to
bring the application processors (APs) from reset using X2APIC mode.
[INFO ] LAPIC 0x10 switched to X2APIC mode.
...
[DEBUG] Attempting to start 3 APs
[DEBUG] Waiting for 10ms after sending INIT.
[DEBUG] Waiting for SIPI to complete...
[DEBUG] done.
[DEBUG] Waiting for SIPI to complete...
[DEBUG] done.
[ERROR] Not all APs checked in: 0/3.
[DEBUG] 0/3 eventually checked in?
[ERROR] MP initialization failure.
[ERROR] MP initialization failure.
Note: The AP bring up flow between XAPIC and X2APIC are the same
except the way to access those LAPIC registers. X2APIC expects to
access all LAPIC registers using MSR (base with 0x800).
The correct flow to enable X2APIC on MTL would be as follows:
1. Let BSP bring all APs in XAPIC mode.
[INFO ] LAPIC 0x10 in XAPIC mode.
...
[DEBUG] Attempting to start 3 APs
[DEBUG] Waiting for 10ms after sending INIT.
[DEBUG] Waiting for SIPI to complete...
[DEBUG] done.
[DEBUG] Waiting for SIPI to complete...
[DEBUG] done.
[INFO ] LAPIC 0x11 in XAPIC mode.
[INFO ] LAPIC 0x0 in XAPIC mode.
[INFO ] LAPIC 0x80 in XAPIC mode.
2. Call enable_x2apic() function on all CPUs (BSP and APs)
And at the end of #2 above, all cores will now switch to X2APIC
from XAPIC.
[INFO ] Initializing CPU #0
[DEBUG] CPU: vendor Intel device a06a0
[DEBUG] Clearing out pending MCEs
[INFO ] LAPIC 0x10 switched to X2APIC mode.
...
[INFO ] CPU #0 initialized
[INFO ] Initializing CPU #1
[DEBUG] CPU: vendor Intel device a06a0
[DEBUG] Clearing out pending MCEs
[INFO ] LAPIC 0x11 switched to X2APIC mode.
Note: Intel MTL FSP also follow the same steps for x2APIC enablement
while coreboot selects USE_INTEL_FSP_MP_INIT config instead
MP_SERVICES_PPI_V2.
BUG=b:219061518, b:219053812
TEST=Able to perform coreboot doing AP init with
DEFAULT_X2APIC_LATE_WORKAROUND config enabled without running into
any hang issue.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: Ie9c8fad6c46b15b5b08c9cc4ef53f2a6872bd0ea
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65741
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch fixes a missing header file compilation issue when coreboot
selects MP_SERVICES_PPI_V2 config from MTL SoC.
The `MpServices2.h` file doesn't exist in the upstreamed EDK2 repo
(integrated with `edk2-stable202111` stable tag).
Currently MpServices2.h file is being copied from the
`edk2_stable202005` stable tag.
BUG=b:237960384 ([Intel FSP][EDK2011] MpServices2.h header is missing
in upstream EDKII git)
TEST=Able to fix the compilation issue on Google/Rex (Meteor Lake)
when MP_SERVICES_PPI_V2 kconfig is enabled.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: Ib7c406ff51439c93c6d15f3a69808b4d1590cfa5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65624
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Intel Meteor Lake SoC expects to select late x2APIC enablement where
AP bring up will use xAPIC and later x2APIC gets enabled using CPU init.
This patch provides an option where SoC code choose the correct
LAPIC access mode using choice selection.
BUG=b:219061518, b:219053812
TEST=Able to build Google/Rex.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I6b50a0f5e39a95c25cd2c72219d2b402550a6fad
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65786
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add option to do AP bringup with LAPICs in XAPIC mode and
switch to X2APIC later in CPU init.
Change-Id: I94c9daa3bc7173628f84094a3d5ca59e699ad334
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65766
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Commit e54a8fd43247d767f16a37f3e3150b2915d809bc (soc/intel/meteorlake:
Add entry for GSPI2 device) added an entry for the GSPI2 device in the
devicetree, but did not add any other entries. Ensure that the rest of
the code is aware of the GSPI2 device to avoid any problems.
Change-Id: Ib59bd289751bd96402c4adc61ffbee3bebe0edb0
Found-by: Coverity CID 1490681
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65916
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
|
|
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Change-Id: Id56310bd616cd19fee5dc934676006b2dc34b1ff
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65929
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Change-Id: I37ed13e1fa318ca0f8381f5b1b409bf80fa4da11
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65888
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
The `IMAGE_ALIGN` macro is unsafe because its value is compound and is
not enclosed in parentheses, which can cause operation order problems.
However, as this macro is unused, remove it instead of fixing it.
Change-Id: I099c291f44d5a2c9d32c9ff071374016ed27eee8
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65930
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
|
|
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Change-Id: Iba81be8ec48fa744f3263e340267a56158656a8f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65903
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Change-Id: Ibe20d48bdd8c776f9658620a13814f96e564dabc
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65907
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Change-Id: I04951bf142fc4061960f42ad7ae702a70215e658
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65906
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Change-Id: I90278683bc22d87364453f316c05afe4cd96b383
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65904
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Change-Id: I1497c7589570b8ff3873149a0fb212bad96ad432
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65902
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Change-Id: I420b9506381758c63b88435a915672507e8bc465
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65901
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Change-Id: I54438978db13ba00188e53239f7034d1b258e912
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65900
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Change-Id: If8b2db7ff816b9953e9bb767f0f406417e297386
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65899
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Change-Id: I0a11d303d2e2c83cb72773656f5caedec666dc66
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65898
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Change-Id: I47ee16f2d4be34c42b2e7f9fa4c3a72a7a95967f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65897
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Change-Id: I4c5dffb32e1ed858e93f95ed17eac894a9100501
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65896
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Change-Id: I7b6e41fa3b7cd8c8f7327c690212ec4990e8baf5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65895
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Change-Id: I18120ba93140e2dced7c8d9aafa34a834d1df842
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65894
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Change-Id: I9261c89b8a15f1ea2f5883481a1cdb7fc8664bb0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65893
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Martin L Roth <gaumless@tutanota.com>
|
|
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Change-Id: Icfd36e0ee524e0e2dc1dd6b0ee39a5c1ae31f4ea
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65892
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Change-Id: If7cac72e0bbdefdb4b6e2697df69a061a23e8684
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65891
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Change-Id: Ia92acfa006ae44fc2969a92b4b21a2c27e0f01be
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65890
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Change-Id: Ifc915e2825724fdaac67d259e1af2079893492a0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65889
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Change-Id: I490a7f0c9cb32ca1ea246c14b72852814553214f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65905
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
It probably was supposed to be *making these names conistent …*, but
short that a little, and add a missing article.
Change-Id: If88ff6d7b0a61aa83d5822b5e1c0b5b4c9d3bb3c
Fixes: ac136250b26d ("commonlib: Substitude macro "__unused" in compiler.h")
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65884
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Change-Id: I15d7e2f30b054d14009761006a2f89f45e001118
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65838
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Change-Id: I9b710d279da6db9125519f58ecba109a4d9fa8e3
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61554
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
|
|
Change-Id: Id33ef66e7388df2173ee8888265ed4379f05a93e
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61548
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
|
|
"else" is unuseful after a "break" or "return".
Change-Id: I7273b9af46a2310c9981ffd20afe2c8c7e061479
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/60910
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
|
|
Change-Id: Ic1b38e93d919c1286a8d130700a4a2bfd6b55258
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61557
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
|
|
Change-Id: I3e439a293c6b4a806cae7c6a56d28e61f7e57044
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61555
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
|
|
These enums & macros will be used to report resources with acpigen_*
functions (Currently those resources are reported in northbridge.asl,
but follow-up CLs will remove this file and add the need acpigen code).
BUG=b:148759816
BRANCH=firmware-brya-14505.B
TEST='emerge-brya coreboot chromeos-bootimage' builds correctly.
Tested on an Anahera device which successfully boots to ChromeOS
with kernel version 5.10.109-15688-g857e654d1705.
Change-Id: I5b95c9b8370db63537eb48b640ad8f0e750efd69
Signed-off-by: Eran Mitrani <mitrani@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65768
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Use correct HID names instead of the CID names for the touchpad devices.
Drop the now unneeded UID for the gaze15 TP devices.
Tested on a gaze15 with a Synaptics device. Windows does not crash on
boot and the touchpad is still detected as an I2C HID device.
Change-Id: I5b6ab1a23ce667754d0c5757062385a721c5113f
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65723
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
|
|
1. Add wifi sar table for osiris
2. Set EC_GOOGLE_CHROMEEC_INCLUDE_SSFC_IN_FW_CONFIG
BUG=b:234951991
TEST=build FW and checked SAR table can load by WiFi driver.
Cq-Depend: chrome-internal:4871098
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: I301dce3229a24dd72b12b84d9eb7606abe10cbba
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65869
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Ren Kuo <ren.kuo@quanta.corp-partner.google.com>
|
|
Configure the dGPU power and reset pins in bootblock instead of
ramstage. This fixes a conflict with our downstream driver, which
configures these pins to enable dGPU power in romstage. Behavior remains
unchanged without the driver as the dGPU is left powered off.
Change-Id: Ica5ad5adc20fc2629d913b76a5a781fbd59a569d
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65801
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
|
|
As per Intel Dynamic Tuning Spec revision 1.3.13, section 14.1.2 TBAT
_UID should match the _UID implemented for battery device ACPI object
for OS
_UID for TBAT is currently set to "TBAT" but should be 1.
Battery device is define at src/ec/google/chromeec/acpi/battery.asl
Setting _UID to 1 because right now ChromeOS is the only user
of DPTF driver
TEST: Build and boot brya0
Signed-off-by: Varshit B Pandya <varshit.b.pandya@intel.com>
Change-Id: I1e4474e59cf01f937fbd51e5b674a609f0c47625
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65605
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
The oryp5 has several issues with audio output after a reboot:
- The device is not in GNOME sound settings
- The device is in GNOME sound settings, but there is no audio output
- The speaker output is significantly louder than normal
Reset the audio codec to resolve these issues.
Tested on Pop!_OS 22.04 with Linux 5.17.15.
Change-Id: I42f642820bba82142ff370930f0a25e9d1025588
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65733
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
|
|
The APOB in sabrina is larger than in cezanne/picasso and no longer
fits in the previously allocated 64K space for it. Other symbols are
placed immediately after the APOB region and end up corrupting the APOB
data on sabrina.
Add a Kconfig option to specify the APOB size in DRAM to reserve enough
memory and increase the size for sabrina to 128K
TEST=Timeless builds are identical for mandolin/majolica for PCO/CZN.
Build chausie and verify symbols do not overlap _apob region
BUG=b:224056176
Signed-off-by: Fred Reitberger <reitbergerfred@gmail.com>
Change-Id: Ia5dbacae67ff02fc8a6ec84b9007110ca254daa3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65852
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Battery charging thresholds are a firmware implementation and not
dependent on any hardware. It is expected that all boards using System76
EC firmware will select this option, so enable it by default.
Leave it disabled on clevo/cml-u, which didn't have it selected.
Change-Id: Id99d36eaf055a76b9e1eb732174017651de299a5
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65714
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
|
|
For brya, I2C1 is cr50, and I2C3 is Touchscreen
BUG=None
BRANCH=firmware-brya-14505.B
TEST=None
Signed-off-by: Eran Mitrani <mitrani@google.com>
Change-Id: Id564d5ede43e745c607ddfd851ff03557d76ddec
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65793
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
As part of this CL https://review.coreboot.org/c/coreboot/+/61020
this function was decoupled and support for new DSM was added.
This function is no longer used so remove it.
Signed-off-by: Varshit B Pandya <varshit.b.pandya@intel.com>
Change-Id: Iad9dca8e50bad87178dfcc1951276703721d5f60
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65850
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Meera Ravindranath <meera.ravindranath@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change is to allow AMD MP2 I2C OS driver to access
I2C0/1 devices when MP2 firmware is loaded.
Change-Id: Iaf25eb4dcf949e4b512ec0e86dbe5ccbc91c3d24
Signed-off-by: Ritul Guru <ritul.bits@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65673
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This commit makes gsi_bases platform independent. It introduces two new
Kconfigs which set if there are IIO APICs on other devices than the PCH
or not, and where they do start.
Change-Id: I40db4a8fd90572757687f35bbd8eebd7229fc75a
Signed-off-by: Christian Walter <christian.walter@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65531
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This is based on the following Intel documents:
* 570805
* 570806
* 572062
* 571264
Change-Id: I199415902d26fa5341ef3212a9169836ea4df74a
Signed-off-by: Christian Walter <christian.walter@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65548
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Pujjo only support RTL1019 amp device, remove MX98360A device setting
BUG=b:238716919
TEST=Build and boot on pujjo
Signed-off-by: Stanley Wu <stanley1.wu@lcfc.corp-partner.google.com>
Change-Id: I92ba66e8656ea36511f88cf867f51ba95168592e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65818
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Reka Norman <rekanorman@chromium.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Since ASPM is not verified as fully functional yet, and the board is
still in development, this patch disables ASPM for the dGPU.
BUG=b:236676400
TEST=boot to OS in agah, lspci -vvv shows ASPM is disabled
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I525eeb18c57d45fd55335b63a59262066afc9567
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65566
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Ivy Jian <ivy.jian@quanta.corp-partner.google.com>
|
|
init overridetree.cb based on the latest schematic.
BUG=b:237628218
TEST=USE="project_joxer emerge-nissa coreboot"
Signed-off-by: Mark Hsieh <mark_hsieh@wistron.corp-partner.google.com>
Change-Id: I22778cc2582abdc2e62d98c6b049a0fa4dd467e6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65662
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Reka Norman <rekanorman@chromium.org>
|
|
The validation process verifies that hardware components comply with
the standard hardware specifications. For instance, PCI express
implementation must comply with the hardware PCIe specification
requirements: Electrical, Configuration, Link Protocol and Transaction
Protocol. To perform these tests the hardware must be configured in a
particular state: some feature related to power management need to be
turned off, hot plug should be enabled...
This patch sets the appropriate FSP Updateable Product Data flags to
get the hardware in the proper configuration:
- Enable PCIe hotplug on all ports
- Set clock sources to run free
- Set the FSP compliance test mode flag
BUG=b:235863379
TEST=Compilation with and without the flag
Verify code path with instrumentation
Signed-off-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Signed-off-by: Jeremy Compostella <jeremy.compostella@intel.com>
Change-Id: Ic07b9276121dfbd273a8f63a1f775ddbd3566884
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65114
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
This config can be used to make coreboot configure the hardware to
meet compliance tests requirements. SoCs which support compliance
testing features should set the
SOC_INTEL_SUPPORTS_COMPLIANCE_TEST_MODE flag.
BUG=b:235863379
TEST=Successful compilation
Signed-off-by: Jeremy Compostella <jeremy.compostella@intel.com>
Change-Id: Iec760ae89e2b892ef45e6750e823ab5a8609d0fa
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65091
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Update DDR4 SPDs to Eldrid to include the following:
DRAM Part Name ID to assign
H5AG36EXNDX019 0 (0000)
BUG=b:236739240
BRANCH=Volteer
TEST="FW_NAME=eldrid emerge-volteer coreboot" and verify it builds successfully.
Signed-off-by: Johnny Li <johnny_li@wistron.corp-partner.google.com>
Change-Id: I2c372fa40899aa750d335825cf3880bc52a612a7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65819
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This moves the die() statement to a common place.
Change-Id: I24c9f00bfee169b4ca57b469c089188ec62ddada
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65812
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
This allows the compiler to optimize out code called after run_ramstage.
Also remove some die() statements in soc code as run_ramstage already
has a die_with_postcode statement.
Change-Id: Id8b841712661d3257b0dc67b509f97bdc31fcf6f
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65811
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
It turns out that there is no device connected to I2S2.
This patch clarifies the GPIO settings device association and remove
unnecessary configuration.
GPP_A8 -> default: GP-in ; set to NF1: SRCCLKREQ7#
GPP_A9 -> default: NF1: ESPI_CLK
GPP_A10 -> default: NF1: ESPI_RESET#
BRANCH=firmware-brya-14505.B
Signed-off-by: Cliff Huang <cliff.huang@intel.com>
Change-Id: I7a575f495d841fe0bf6fd86a84caeee064f6904b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/65494
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jérémy Compostella <jeremy.compostella@intel.com>
Reviewed-by: Bora Guvendik <bora.guvendik@intel.com>
|
