| Age | Commit message (Collapse) | Author |
|---|
|
LynxPoint-LP has an additional 16 entries in the IOAPIC that
can be assigned to specific GPIOs when they are configured
as PIRQ.
The maximum redirection entries field in the IOAPIC needs to
be set to 0x27 when this is enabled.
Additionally specific GPIOs need to be routed to PIRQ so they
interrupt via the IOAPIC instead of the GPIO IRQ 14/15.
Change-Id: Ie587e1d203422ff6fb7fc5056d20a5ae66720991
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/56620
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4203
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
The LynxPoint southbridge ACPI code needs the SSDT2 table to function
properly. Otherwise the ACPI evaluator in the kernel spews errors.
Change-Id: I73918545a07e43f4a281ff34d8537340d601b102
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/56601
Reviewed-on: http://review.coreboot.org/4188
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Mainboards were defining their own SMBIOS type41
write function. Instead pull this into the generic
SMBIOS code and change the existing mainboards to
make use of it.
Change-Id: I3c8a95ca51fe2a3118dc8d1154011ccfed5fbcbc
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/56619
Reviewed-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/4187
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
A parrot device with a bad flash part has been seen to hang
in the elog_shrink code becuase the flash was not successfully
erased and it gets stuck in a loop trying to shrink the log
and then add an event.
Change-Id: I8bb13dbadd293f9d892f322e213c9255c8e9acb3
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/56405
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4186
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Update and use the new pei_data data structure. Now that the
reference code is fixed it's possible to properly disable/enable
the USB2 and USB3 ports correctly.
Change-Id: I075c646e7574be354420b6e59507e8917a97d0f0
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/56594
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/4185
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
- Only the first two DIMM SPDs are specified so far
- GPIO map is updated
- iSSD power sequencing removed
- USB port map updated
Change-Id: I4172460d3b075bfd5bb22013a6225cf0e8f95b9c
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/56329
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4184
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
The ssdt2 generation code was calling acpigen_patch_len().
However, none of the entries had AML object lengths that
needed patching. That resulted in the following message:
ASSERTION FAILED: file 'src/arch/x86/boot/acpigen.c', line 52
Additionally, this caused an errant write to a memory address
whose value was in the variable ltop. This was the 0 address.
Change-Id: I44abf5a4e4225220575aee6b5c9bb6b0be093a28
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/56299
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/4182
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
The ACPI code was defining two EHCI controllers and ignoring
the XHCI controller. This changes the second EHCI controller
to be XHCI instead and changes the wake resource to indicate
S3 and not S4.
cat /proc/acpi/wakeup
Device S-state Status Sysfs node
HDEF S4 *disabled pci:0000:00:1b.0
EHCI S3 *enabled pci:0000:00:1d.0
XHCI S3 *enabled pci:0000:00:14.0
Change-Id: If28775e6ef8608c22c85ca91d91d1f598ec7755d
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/56263
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4181
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
The clock gating register at offset 0x800 is managed by the
clock driver in the kernel when the devices are in ACPI mode.
When in PCI mode we should force enable the clock here.
When in ACPI mode or the device is disabled it should be put
in D3Hot state.
> i2cdetect -y -r 10
0 1 2 3 4 5 6 7 8 9 a b c d e f
00: -- -- -- -- -- -- -- -- -- -- -- -- --
10: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
20: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
30: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
40: -- -- -- -- 44 -- -- -- -- -- -- -- -- -- -- --
50: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
60: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
70: -- -- -- -- -- -- -- --
Change-Id: Ib93ffd41bf36386d5ce63bfc0ae6597f3e23bc48
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/56122
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4180
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Enable GPIO SMI for GPIO34 and set it as inverted so it
is only generated when it is raised by the EC.
1) ec console command: lidopen
2) wait until booted to developer screen
3) ec console command: lidclose
4) ensure system turns off
Change-Id: I7d50f171f3f4539c7c264103d1ffc7c5d0f1c7ba
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/56052
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4177
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
The vendor ids were never updated to reflect LynxPoint's device
ids. Therefore, none of the initialization was being ran. Fix
this.
Change-Id: Ic6ec00c9fb1cbcb6087fd89b0acff3d83294ac6a
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/55821
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/4173
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
In order to report whether coreboot enabled a SerialIO device
in ACPI mode we had been relying on reading NVS in the _STA
method for the SerialIO device.
The ACPI _STA method has restrictions on what it can access
and is unable to access OperationRegions outside its scope
which means it should not be trying to read NVS.
This change adds a new SSDT to the ACPI tables and fills it
with constants that indicate whether or not a device is enabled
in ACPI mode.
The ACPI code is changed to read these variables from the
SSDT and use that instead of trying to query a variable in NVS.
Attempt to use lpt-clk driver to probe the
device clocks for SerialIO devices and see that the kernel
does not complain about accessing the GNVS region.
Change-Id: I8538bee4390daed4ecca679496ab0cb313f174ce
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/51369
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4170
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
- Disable EC software sync for now
- Report correct EC active firmware mode
- Force enable developer mode by default
- Set up PCH generic decode regions in romstage
- Pass the oprom_is_loaded flag into vboot handoff data
Change-Id: Ib7ab35e6897c19455cbeecba88160ae830ea7984
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/51155
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4169
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
These boards were returning 0 to indicate success when
the realmode handler expects it to return 1 to indicate
that it handled the interrupt.
Change-Id: I2baeaf8c2774fa7668a8b2f2d9ad698302eefb21
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/50881
Reviewed-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/4168
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
These are both pulled up to 3.3V in the schematic.
Change-Id: I12e055a39ff6100300c3d285899b8d6239e3773d
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/50356
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4164
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
In order for the FIT entries to be populated in the table the
update-fit command needs to be done on the coreboot image. That
way the microcode entries are added to the table properly.
Change-Id: I44595aee1ca710f4f04d482d8900cf95fbc1797f
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/50317
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/4159
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
In order to probe the gpio-lynxpoint kernel driver the
LP GPIO controller needs to be exposed as a specific
ACPI device.
This also allows the resources to be exposed to the OS via
this device instead of the catch-all LPC device.
Ensure the driver loads at boot:
gpiochip_find_base: found new base at 162
gpiochip_add: registered GPIOs 162 to 255 on device: INT33C7:00
Also ensure the driver is visible in sysfs:
$ cat /sys/devices/platform/INT33C7:00/gpio/gpiochip162/label
INT33C7:00
Change-Id: I9f79c008f88da9b67ed1cdfdb9d3a581ce8f05ff
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/50215
Reviewed-on: http://review.coreboot.org/4158
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
In the process of getting rid of compiler includes during in coreboot
and libpayload, we defined size_t and ssize_t ourselves, using a GCC
macro for size_t: __SIZE_TYPE__. Unfortunately, there is no
__SSIZE_TYPE__, so we temporarily redefine unsigned to signed to make
__SIZE_TYPE__ __SSIZE_TYPE__.
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Change-Id: I4cf4eb0fdaa4db64277c2585fe2c1bdc0acdf02b
Reviewed-on: https://gerrit.chromium.org/gerrit/49947
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Commit-Queue: Stefan Reinauer <reinauer@google.com>
Tested-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/4156
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Now that we have RW ramstage we don't need to have the
management engine lock down step done in a final SMM.
ME: mkhi_end_of_post
ME: END OF POST message successful (0)
PCI: 00:16.0: Disabling device
Change-Id: I9db4e72e38be58cc875c1622a966d8fcacc83280
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/49757
Reviewed-on: http://review.coreboot.org/4153
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
There were two undefined MBP types that are now defined.
These include NFC status and some interesting timing data.
ME: Wake Event to ME Reset: 6 ms
ME: ME Reset to Platform Reset: 7 ms
ME: Platform Reset to CPU Reset: 51 ms
Change-Id: I67bf1f303f3c32497041e64c40eb9ccb6a63d88a
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/49756
Reviewed-on: http://review.coreboot.org/4152
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Instead of having an OS re-parse cbmem book-keeping records
for the cbmem allocator just to get the console buffer export
the pointer to the memory console directly in a field named 'CBMC'.
This field lives in the GNVS table.
Change-Id: Ief0c4da7b18df66feb9c816c9f4abdf5a72bd3a4
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/49764
Reviewed-by: Stefan Reinauer <reinauer@chromium.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/4149
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
If elog_clear is called before other elog functions, for instance if it's
called through an SMI immediately after the system boots, then the elog data
structures won't have been set up and the system will go off the deep end.
This change adds a call to elog_init to elog_clear to make sure things things
are always initialized before we start using them.
Before this change, this command would cause
the system to lock up if run immediately after boot:
echo 1 > /sys/firmware/gsmi/clear_eventlog
After this change, that results in the log being cleared correctly.
Change-Id: I45027f0dbfa40ca8c581954a93b14b4fedce91ed
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: https://gerrit.chromium.org/gerrit/49303
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Stefan Reinauer <reinauer@google.com>
Commit-Queue: Gabe Black <gabeblack@chromium.org>
Tested-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/4144
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Slight tweaks found when looking at latest ref code when
investigating package C-state issues.
A few bits in the clock gating register don't match the
documentation and are also cleaned up.
Change-Id: I36ced7280c160b114c70b2eeafc8b24813ff2f6a
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/49330
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4142
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
The mainboard_interrupt_handlers() argument for the function
pointer was using void * as the type. This does not allow the compiler
to catch type differences for the arguments. Thus, some code has been
committed which violates the new interrupt callbacks not taking any
arguments. Make sure the compiler provides a type checking benefit.
Change-Id: Ie20699a368e70c33a9a9912e0fcd63f1e6bb4f18
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/48970
Reviewed-on: http://review.coreboot.org/4141
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Some handlers still had 2 variants, others were
incorrectly guarded by CONFIG_ variables. This
patch straightens them out.
This does not touch the siemens/sitemp_g1p1 which
provides an interestingly complex solution for the
int15 handler.
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Change-Id: I5d74fdf7c2ab1faa96ebc2b5ca5c69398449b069
Reviewed-on: https://gerrit.chromium.org/gerrit/48979
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Commit-Queue: Stefan Reinauer <reinauer@google.com>
Tested-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/4140
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
The EC saves its last "shutdown reason" for the system in EC RAM
that we can read back and log on boot.
The decode for the "reason" field will be added to mosys.
Change-Id: I834d39122e45262ef8e7ba59201accbee5857aac
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/48323
Reviewed-by: David James <davidjames@chromium.org>
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Commit-Queue: Stefan Reinauer <reinauer@google.com>
Tested-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/4127
Tested-by: build bot (Jenkins)
|
|
The format of this function changed but was not updated in
all mainboards. This fixes all Sandybridge/Ivybridge boards.
The int15 handler no longer takes a regs structure as an
argument and instead uses global variables. The yabel interface
is now similar enough that we can drop the duplicate handler.
Change-Id: Icdaae4d6d50884f6d7bce7a167d48cb1d4807010
Reviewed-on: https://gerrit.chromium.org/gerrit/48969
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Commit-Queue: Stefan Reinauer <reinauer@google.com>
Tested-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/4135
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
Recent commit proposal by Ron Minnich proposes to move to native gfx init for
qemu. Unfortunately we didn't have native init for default qemu video (cirrus)
Here is one extracted from GRUB one which I wrote couple of years ago.
Change-Id: Icb89cf918ef5d276bcc703c48c568e7b9c1be756
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/4270
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Including raminit
Change-Id: If1dd3855181481b8b928adf0fdb40b29d15897db
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/4044
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
Part of X201 port.
Change-Id: If17d707004aba9f08459dbd8f3a146fa3c076aa9
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/4052
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
|
|
Per our discussions with Gerd, qemu will now always do native graphics
on coreboot. The VGA BIOS capability is not needed and will no longer
be supported. Attempts to build without native graphics will result in
an error.
This code builds for both x86 emulation targets. I'm hitting an issue
testing that is unrelated to coreboot; if someone can test, that
would be helpful. Be sure to start qemu with -vga std.
We also add a test for the PCI BAR being zero and return silently if it
is.
Change-Id: I66188f61e1bac7ad93c989cc10f3e0b55140e148
Signed-off-by: Ronald G. Minnich <rminnich@google.com>
Reviewed-on: http://review.coreboot.org/4258
Tested-by: build bot (Jenkins)
Reviewed-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
|
|
Needed to make dock work on X201.
Change-Id: Id0b32266cacf04bb48530bedf50818c268f947ec
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/4081
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Tested-by: build bot (Jenkins)
|
|
SandyBridge raminit uses this CMOS option. If it is not declared, the build
fails when USE_OPTION_TABLE is selected.
Change-Id: I1ba1f994d4ea3824dc66e8f35d0b5b24b88d4dd6
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-on: http://review.coreboot.org/4269
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
the part !CAR && PRE_RAM is obviously meant as dummies. Unfortunately
cbmemc_tx_byte has wrong number of arguments and hence causes compilation
failure.
Found out when compiling for vexpress-a9.
Change-Id: Ic84d142bac5c455c2371fbc9439c898de04a974e
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/4267
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
This was changed to 0x80000000 in SA BWG 1.5.0.
Change-Id: Ic6773f45057f3eb93b2d93ee543e3db77fccf805
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/50852
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4166
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
[ 1.503741] microcode: CPU0 sig=0x40651, pf=0x40, revision=0x10
[ 1.510483] microcode: CPU1 sig=0x40651, pf=0x40, revision=0x10
[ 1.517213] microcode: CPU2 sig=0x40651, pf=0x40, revision=0x10
[ 1.523947] microcode: CPU3 sig=0x40651, pf=0x40, revision=0x10
Change-Id: I19ef40b636eebeb8cc29cc0404abbe263ec8eaa7
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/50655
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4165
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
With the XHCI controller enabled we no longer hang the
system when dropping into a package C-state so remove
the code that was disabling it.
Change-Id: Icd60488fd2506dac04fb6ec96a77bec265b10d8c
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/50355
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4163
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
The chromeos_acpi driver sysfs naming is not what
crossystem expects if there is just one entry in the package
because it does not add a ".#" suffix in that case.
Specify all the expected GPIOs on wtm2 as undefined, which
should be 0xFF and not 0x00 becuase 0 is a valid GPIO.
Change-Id: I9b17e9bab94219695e65b17914c84acf02a0983b
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/50337
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4162
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
The current microcode blobs contain both ULT and non-ULT
revisions. Only include one or the other based off of the
CONFIG_INTEL_LYNXPOINT_LP Kconfig option.
Change-Id: I3e4e41d4cd727b1a974361fb469267e6f6022d5a
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/50318
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/4160
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
For all the current haswell boards enable the monotonic timer.
The ULT boards use the 24MHz MSR while the non-ULT boards use the
local apic.
Change-Id: I8b19f526a5a49e8467f296c566a2c4263bc5a863
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/49763
Reviewed-by: Stefan Reinauer <reinauer@chromium.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/4148
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
Change-Id: I714208da23bf7cbd1232874c05ad3100551f5f7c
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/49647
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4146
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
This reads PCH power levels via PCODE mailbox and writes the
values into the PMSYNC registers as indicated in the BWG.
Change-Id: Iddcdef9b7deb6365f874f629599d1f7376c9a190
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/49329
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4143
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
On haswell ULT systems there is a 24MHz clock that continuously runs
when deep package c-states are entered. The 100MHz BCLK is shut down
in the lower c-states. When the package wakes back up a conversion
formula needs to be applied. The 24MHz calibration is done using the
internal PCODE unit.
Change-Id: I6be7702fb1de1429273724536f5af9125b98da64
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/48292
Tested-by: Stefan Reinauer <reinauer@google.com>
Commit-Queue: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/4136
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
The c-states are configured according to the BWG, however the
package c-states are disabled as they currently cause platform
instability. The exposed ACPI c-state to processor c-state mapping
are as follows for ULT boards:
ACPI(C1) = MWAIT(C1E)
ACPI(C2) = MWAIT(C7S long latency)
ACPI(C3) = MWAIT(C10)
The non-ULT boards have an expoed c-state mapping:
ACPI(C1) = MWAIT(C1E)
ACPI(C2) = MWAIT(C3)
ACPI(C3) = MWAIT(C7S)
Included in this patch is removing the updating of current limit
registers as some of the MSRs are different and the proper values
are currently unknown. Lastly, some of the MSRs were renamed to
match the BWG.
Booted 3.8 kernel and used powertop to note package, core, and acpi
c-state residency.
Change-Id: Ia428d4a4979ba3cba44eb9faa96f74b7d3f22dfe
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/48291
Commit-Queue: Stefan Reinauer <reinauer@google.com>
Tested-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/4133
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
This will be used in a later commit to do some specific
power sequencing.
Change-Id: Id7f033bb80aed915c2498ea910cb3ac7290da37f
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/48947
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4137
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
This adds some macros for the common GPIO defines and drops
the gpio number definition from each entry. The end result
is much easier to read. The wtm2 mainboard gpio list is modified
to use this.
Also fix a bug in the LP version of get_gpio() that was always
returning zero due to a miscompare.
Change-Id: I143e5aee412af1eda84e35f8026f31cf13df508e
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/48946
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4138
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
With the LynxPoint chipset there are more than 16
possible GPIOs that can trigger an SMI so we need
a mainboard handler that can support this.
There are only a handful of users of this function
so just change them all to use the new prototype.
Change-Id: I3d96da0397d6584f713fcf6003054b25c1c92939
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/49530
Reviewed-by: Stefan Reinauer <reinauer@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4145
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
These are placeholder values until we can configure for
the exact panel.
Change-Id: Ibe88cc3588947366eb1728e5b3e1ab8c8be6dfe8
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/56807
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4196
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
Minor tweaks to variable names in the slippy mainboard
that make it easier to base a new board from without
as much renaming.
Also properly set up the thermal variables for the
thermal zone that is defined in ACPI instead of using
the generic setup from WTM2.
Change-Id: I752c1a50bfdc06b6ddad95bd1331c6870b9f9df2
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/56328
Reviewed-on: http://review.coreboot.org/4183
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
This will log and clear EC events so they do not take effect
when the SMI handler is enabled.
Change-Id: I5ef563f7cedc8977410cc3f69e2655fc4e14c9eb
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/56055
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4178
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
The SerialIO devices have specific requirements for PCI
interrupt mode to use PIRQ{E,F,G,H} that are not being met.
D21:F0 uses PIRQE, which must not be shared with other PCH
D21:F1-F6 share PIRQF, which must not be shared with other PCH
D23:F0 uses PIRQH, which must not be shared with other PCH
- Fix D20IR -> D20IP typo
- Remove D25/EHCI2 as it does not exist
- Reorder other interrupts to clear PIRQE/PIRQF/PIRQH
Check device interrupts in the kernel
0: IO-APIC-edge timer
1: IO-APIC-edge i8042
8: IO-APIC-edge rtc0
9: IO-APIC-fasteoi acpi
16: IO-APIC-fasteoi ath9k
18: IO-APIC-fasteoi i801_smbus
19: IO-APIC-fasteoi ehci_hcd:usb1
21: IO-APIC-fasteoi i2c-designware-pci--1, i2c-designware-pci--1
40: PCI-MSI-edge PCIe PME
41: PCI-MSI-edge i915
42: PCI-MSI-edge ahci
43: PCI-MSI-edge xhci_hcd
44: PCI-MSI-edge snd_hda_intel
Change-Id: Id4c08d11d2860f270c6387138acdc7d3d83a85b5
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/56028
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4176
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
The dev screen was not displaying properly. With the
PWM values programmed the screen displays correctly.
Change-Id: I82b56a92e4168022082a2e519026977ee2ae0c9e
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/51472
Reviewed-on: http://review.coreboot.org/4172
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
The device at function 0 also needs to be enabled
or the kernel will ignore all other functions.
00:15.0 DMA controller: Intel Corporation Lynx Point-LP Low Power Sub-System DMA (rev 03)
00:15.1 Serial bus controller [0c80]: Intel Corporation Lynx Point-LP I2C Controller #0 (rev 03)
00:15.2 Serial bus controller [0c80]: Intel Corporation Lynx Point-LP I2C Controller #1 (rev 03)
Change-Id: I0e1bc7bb719756496c46664d66dc1b1cf2f4d1ba
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/51370
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4171
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
This lets the keyboard init get called properly.
Change-Id: I11ffb459907188a58149d28a6ade0b7de7d15d08
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/50853
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4167
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
Change-Id: Iae0258ceb0424df0937d2cec7dd885060f5b4e48
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/50082
Reviewed-on: http://review.coreboot.org/4157
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
Change-Id: I7a617fe06d23b906f718ed30f1378f7d220b2799
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/49911
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4154
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
- 0x200-0x208 for host command window
- 0x800-0x8ff for host command arguments and parameters
- 0x900-0x9ff for exported EC memory map
Change-Id: I064b969843ef0d3c602793d1cb3d82715775c05e
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/49755
Reviewed-on: http://review.coreboot.org/4151
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
Without an LM10506-A the power sequencing for this
part needs to be done manually using GPIOs.
Change-Id: I842152e5f7c30c8dbe37df0c344935a659eb2887
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/49648
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4150
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Change-Id: I33876b90902d4a08d760eb482b08ba41be6e3695
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/49531
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4147
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
Change-Id: I1bdc52efc827c331c53b97d2b96edafc518d05bf
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/4259
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Tested-by: build bot (Jenkins)
|
|
This removes an earlier patch that caused the VGA option ROM to be loaded by
coreboot even in normal mode when it isn't needed.
Change-Id: Ie0a331a10fff212a2394e7234a0dbb37570607b7
Signed-off-by: Bill Richardson <wfrichar@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/48173
Commit-Queue: Stefan Reinauer <reinauer@google.com>
Reviewed-by: Stefan Reinauer <reinauer@google.com>
Tested-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/4125
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
The patch was made by Peter Stuge, I just split it
and added a commit message.
Change-Id: Ieaaaa2611f7bb8968f01b16daefe7e2afe870f72
Signed-off-by: Denis 'GNUtoo' Carikli <GNUtoo@no-log.org>
Reviewed-on: http://review.coreboot.org/4001
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
The patch was made by Peter Stuge, I just split it
and added a commit message.
Change-Id: I4e88c26b70ea8cb249d7613c749b3edc5e3b5e7f
Signed-off-by: Denis 'GNUtoo' Carikli <GNUtoo@no-log.org>
Reviewed-on: http://review.coreboot.org/4000
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Without that fix the GTT points at 0x00000000.
The patch was made by Peter Stuge, I just split it
and added a commit message.
Change-Id: Ia378b600ba2faf00d42635c6503b94ff0cb1bc8c
Signed-off-by: Denis 'GNUtoo' Carikli <GNUtoo@no-log.org>
Reviewed-on: http://review.coreboot.org/4002
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Change-Id: I054edffbb38b13559da10180fc2c6cd9929ba162
Signed-off-by: Denis 'GNUtoo' Carikli <GNUtoo@no-log.org>
Reviewed-on: http://review.coreboot.org/3999
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Move into src/cpu/dmp/dmp_post_code.h
Change-Id: If9f4d842f352eb41618e71f49a226d3cc4ad0b46
Signed-off-by: Andrew Wu <arw@dmp.com.tw>
Reviewed-on: http://review.coreboot.org/3989
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
This permits any software running after the ramstage to tell coreboot that the
boot was successfull.
Change-Id: I6b19160dcf1ea1948360db71d02e344a3bcb44ef
Signed-off-by: Denis 'GNUtoo' Carikli <GNUtoo@no-log.org>
Reviewed-on: http://review.coreboot.org/3992
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
The recommendation from Intel is to report each core as a
separate logical domain in the _PSD table.
This goes against the recommendation in the ACPI specification
because all of these cores are on the same package and share a
VR so they will do voltage transitions together.
The reasoning is that with a larger number of logical processors
the P-state often ramps too quickly resulting in higher power
consumption. By exposing each core as a separate domain the OS
can manage them individually allowing the socket to select the
optimum frequency.
$ cat /sys/firmware/acpi/tables/SSDT > /tmp/SSDT
$ iasl -d /tmp/SSDT
Processor (\_PR.CPU0, 0x00, 0x00000000, 0x00)
{
Name (_PSD, Package (0x01)
{
Package (0x05)
{
0x05,
0x00,
0x00000000,
0x000000FE,
0x00000001
}
})
}
Processor (\_PR.CPU1, 0x01, 0x00000000, 0x00)
{
Name (_PSD, Package (0x01)
{
Package (0x05)
{
0x05,
0x00,
0x00000001,
0x000000FE,
0x00000001
}
})
}
Processor (\_PR.CPU2, 0x02, 0x00000000, 0x00)
{
Name (_PSD, Package (0x01)
{
Package (0x05)
{
0x05,
0x00,
0x00000002,
0x000000FE,
0x00000001
}
})
}
Processor (\_PR.CPU3, 0x03, 0x00000000, 0x00)
{
Name (_PSD, Package (0x01)
{
Package (0x05)
{
0x05,
0x00,
0x00000003,
0x000000FE,
0x00000001
}
})
}
Change-Id: I5ef41b6ead4d88e9ba117003293dbc629c376803
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/48662
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4130
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
$ cat /sys/devices/system/cpu/cpu*/microcode/version
0x8
0x8
0x8
0x8
Change-Id: Id6491ae96c516ae0b55471e53f79f0407cf3ffdb
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/48661
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4129
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Compile was failing with the following error:
In file included from src/vendorcode/google/chromeos/vboot_handoff.h:22:0,
from src/vendorcode/google/chromeos/chromeos.c:22:
vboot_reference/firmware/include/vboot_api.h:388:18: error: unknown type name 'size_t'
src/vendorcode/google/chromeos/chromeos.c: In function 'vboot_get_payload':
src/vendorcode/google/chromeos/chromeos.c:50:23: error: 'NULL' undeclared (first use in this function)
Change-Id: I13f9e41ef6a4151dc65a49eacfa0574083f72978
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/48289
Reviewed-on: http://review.coreboot.org/4131
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Implement proprietary lenovo ACPI hotkeys
Change-Id: I36a6d3a280b0ac76d9ea063cdc10197a57e306f9
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/4055
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
X201 has GPE at 0x11 (17) instead of 28.
Tested on X201.
Change-Id: Ib6306e6f085c4f6811df0789aa402a0d6901ed13
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/4053
Reviewed-by: Idwer Vollering <vidwer@gmail.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
fill_lb_framebuffer
When testing Ron's patch on qemu I found out that fill_lb_framebuffer
overwrites size and tag fields. We need either to fix/check all
fill_lb_framebuffer implementations or write tag/size after fill_lb_framebuffer.
I prefer later as it's more robust.
Change-Id: I98f5bac14f65fb4d990cb21426d402b27f2e8a48
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/4263
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
2065x is with nehalem and not sandybridge.
I don't care much eitherway but it clears some confusion.
Change-Id: Ib2b8e570b830a12ed8d0d313ee4eb56755796d4b
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/4046
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Unlike on X60/T60 dock has to be inited at the same time as EC.
Change-Id: If6eb3140c871859ce99027a50908f72bcc560243
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/4082
Reviewed-by: Idwer Vollering <vidwer@gmail.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
2065x boards don't use MRC. And the space in question isn't used either.
Read number of variable range MTRRs from MSR rather than hardcoding it.
2ff is still zeroed out as unless you zero-out undocumented bits as well
boot fails.
Tested on Lenovo X201.
Change-Id: Ic574193094e7d27c2d6a4d7d3e387d989578532e
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/4080
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
|
|
The mdelay is not necessarry on 2065x.
Tested on X201 that it works without delay.
Change-Id: Ida9e85be7c214f3ba4c9476b5d8a0351e7980e5e
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/4083
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
|
|
On AMD Trinity and Kabini boards errors similar to the following are
shown.
ASSERTION FAILED: file 'src/mainboard/asrock/imb-a180/agesawrapper.c',line 431
DmiTable:100123f7, AcpiPstatein: 10010129,AcpiSrat:0,AcpiSlit:0, Mce:10010de9,Cmc:10010eab,Alib:1002111c, AcpiIvrs:0 in
agesawrapper_amdinitlate agesawrapper_amdinitlate failed: 5
The reason is that on f16kb boards, the CDIT and DMI table are not
created. On f15tn boards, only the DMI table is not created.
Until the root cause is found, disable the table generation to remove
the errors.
Thanks to Wei Hu for debugging and reporting this issue on the list [1].
[1] http://www.coreboot.org/pipermail/coreboot/2013-November/076607.html
CDIT table is not created
Change-Id: I837e3c322bb5331a9b950a72397796a60642c3f3
Signed-off-by: WANG Siyuan <SiYuan.Wang@amd.com>
Signed-off-by: WANG Siyuan <wangsiyuanbuaa@gmail.com>
Reviewed-on: http://review.coreboot.org/4092
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Bruce Griffith <Bruce.Griffith@se-eng.com>
|
|
Current error message refers to sandybridge chipset. Instead error
should be that 2065x needs Ibex Peak.
Change-Id: I8cc8a34f496aec7af0ce95b4b65fd25e165f43fb
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/4202
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
The power to memory is lost during the the suspend, activate
the 3VSBSW# which switches the power during S3 suspend sequence.
As a result resuming from suspend to RAM works now, but now the
GPP ports of the Hudson southbridge are gone after resume from S3.
The devices 15.0 and 15.1 are disabled (decode as ffff) and
therefore anything behind them too [1].
[1] http://www.coreboot.org/pipermail/coreboot/2013-November/076620.html
fam15tn hudson PCIe GPP ports off after resume
Change-Id: Id953313ee4400a03a2ad8ca09e39a5e0d5f92524
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Reviewed-on: http://review.coreboot.org/4041
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Since a long time GRUB 2 is a viable payload alternative to SeaBIOS and
FILO. So make it easy for coreboot users to use GRUB 2 as a payload by
integrating it into coreboot’s build system, so it can be selected in
Kconfig.
As the last GRUB 2 release 2.00 is too old and has several bugs when
used as a coreboot payload only allow to build GRUB 2 master until a new
GRUB release is done. The downside is, that accidental breakage in
GRUB’s upstream does not affect coreboot users.
Currently the GRUB 2 payload is built with the default modules which
results in an uncompressed size of around 730 kB. Compressed it has a
size of 340 kB, so it should be useable with 512 kB flash ROMs.
Tested with QEMU.
Change-Id: Ie75d5a2cb230390cd5a063d5f6a5d5e3fab6b354
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/4058
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
cbfs used u32 in a number of cases where uintptr_t was
correct. This change builds for both 64-bit and 32-bit
boards.
Change-Id: If42c722a8a9e8d565d3827f65ed6c2cb8e90ba60
Signed-off-by: Ronald G. Minnich <rminnich@google.com>
Reviewed-on: http://review.coreboot.org/4037
Tested-by: build bot (Jenkins)
Reviewed-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-by: Aaron Durbin <adurbin@google.com>
|
|
The code is wrong (it's calling ntohl on an entry point that is actually
already le due to an old cbfs bug) and nothing calls it any more anyway.
Change-Id: Ief2c33faf99e3d2fc410524a5aae7bde378f088b
Signed-off-by: Ronald G. Minnich <rminnich@google.com>
Reviewed-on: http://review.coreboot.org/4090
Tested-by: build bot (Jenkins)
Reviewed-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-by: Aaron Durbin <adurbin@google.com>
|
|
Qemu makes the guest uuid (qemu -uuid $uuid) available
to the guest via fw_cfg. Other smbios fields can be
configured in qemu using the -smbios command line
switch (check the qemu manpage for details).
This patch adds coreboot support for this, so the
values provided by qemu will actually show up in the
smbios table.
Change-Id: Ifd9ae0d02749af4e7070a65eadbd1a9585a8a8e6
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-on: http://review.coreboot.org/4086
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Make manufacturer, product_name and uuid smbios fields (type 1)
configurable at runtime, simliar to version and serial number.
Change-Id: Ibc826225e31fa42aa944fa43632dd6a406d5c85d
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-on: http://review.coreboot.org/4085
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Starting with release 1.7 qemu provides acpi tables via fw_cfg. Main
advantage is that new (virtual) hardware which needs acpi support
JustWorks[tm] without having to patch & update the firmware (seabios,
coreboot, ...) accordingly.
So if we find acpi tables in fw_cfg try loading them, otherwise fallback
to the builtin acpi tables.
Change-Id: I792232829b870ff6ed8414a3007e0af17f6c4223
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-on: http://review.coreboot.org/4040
Tested-by: build bot (Jenkins)
|
|
Change-Id: Iec0abae8a4b18ac737e9ebb3eac219182729be0f
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/4057
Tested-by: build bot (Jenkins)
Reviewed-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
For the ram init of Intel Nehalem ram init we need a udelay implementation.
Use common TSC framework for it as Intel Haswell already does.
Change-Id: I360a6db1ec1ba32c92698a7d6f6968c93ead5c52
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/4043
Reviewed-by: Aaron Durbin <adurbin@google.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
|
|
Besides the AGESA static settings, the settings in mainboard/buildOpt.c also
change the final configuration. We need to make sure the settings in FchParam
in resume stage are the same as they were in cold boot stage, otherwise the
board can not wake up more than once.
Tested on AMD/Olive Hill, AMD/Parmer and ASRock/imb-a180.
(USB keyboard doesn't work when board wakes up. It is not introduced by this
patch. It needs more debugging.)
Change-Id: I5a5e5502080e358ffc3577dc6a40bb762844d998
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/3932
Tested-by: build bot (Jenkins)
Reviewed-by: Rudolf Marek <r.marek@assembler.cz>
|
|
qemu 1.7+ provides a fw_cfg file named "etc/e820" with e820-like entries
for reservations and ram regions. Use it for ram detection if present,
otherwise fallback to the traditional cmos method.
Change-Id: Icac6c99d2a053e59dfdd28e48d1ceb3d56a61bdc
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-on: http://review.coreboot.org/4030
Tested-by: build bot (Jenkins)
|
|
Qemu can provide files using the firmware config interface.
This is used to pass config options, virtual machine config
info and option roms into the guest.
This patch adds support for reading the file index and loading
files from qemu.
Change-Id: I57d4a734527c4117239f355121cf1fb8a390ab0d
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-on: http://review.coreboot.org/4029
Tested-by: build bot (Jenkins)
|
|
Change-Id: Ia710eb59f23a52afba2a8ef6e0ff2b2306107245
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-on: http://review.coreboot.org/4033
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Properly build the super i/o .c files. This prevents including
the .c file directly in romstage, which is generally bad practice.
Adding a Makefile and a .h file to include.
Change-Id: I0be66e94d3062a2c4a445cee2f12ec249598dc8b
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-on: http://review.coreboot.org/4014
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Remove the COM port enable loop. There is no need to
search for the port when it is needed and known by the
GPIO function.
Change-Id: Ie4e533fd9e49ed9ae62b209317b4b9853ff9926a
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-on: http://review.coreboot.org/4027
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Add a function to display memory locations in the console
logfile.
Change-Id: Iddb8d2e7a24357075f32c2fdf7916ae7a732247d
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-on: http://review.coreboot.org/4013
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Many chipset devices require additional configuration after
device init. It is not uncommmon for a device early in the devicetree
list to need to change a setting after a device later in the tree does
PCI init. A final function call has been added to device ops to handle
this case. It is called prior to coreboot table setup.
Another problem that is often seen is that the chipset or mainboard
need to do some final cleanup just before loading the OS. The chip
finalize has been added for this case. It is call after all coreboot
tables are setup and the payload is ready to be called.
Similar functionality could be implemented with the hardwaremain
states, but those don't fit well in the device tree function pointer
structure and should be used sparingly.
Change-Id: Ib37cce104ae41ec225a8502942d85e54d99ea75f
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-on: http://review.coreboot.org/4012
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Change-Id: Id4a758644a7b799e7662113c07d395e053525934
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/3984
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Change-Id: I6bb652419a54b7b7190e417346581f38335425ae
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/3985
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Header file is not compatible with romcc, just drop it as a romstage
built with romcc cannot use usbdebug anyway.
Change-Id: If7f8f22d6a8fa1f02157df281f82f02b72b6a609
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/4006
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Removing `-Wno-unused-but-set-variable` from `CFLAGS` the build for
QEMU Q35 and Roda RK9, both using the Intel 82801Ix southbridge, fail
with the following error.
src/southbridge/intel/i82801ix/lpc.c: In function 'i82801ix_enable_apic':
src/southbridge/intel/i82801ix/lpc.c:45:5: error: variable 'dummy' set but not used [-Werror=unused-but-set-variable]
cc1: all warnings being treated as errors
Removing `dummy` should be safe as GCC probably optimizes it away before
anyway. That no dummy variable is used for an RCBA [1] access in Intel
Lynx Point supports that this can be dropped safely.
[1] root complex base address
[2] src/southbridge/intel/lynxpoint/early_pch.c
Change-Id: I1c138a3498228dbd025f68d5e6af0acc29ed3460
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/3982
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
|
