| Age | Commit message (Collapse) | Author |
|---|
|
As the audio card needs 1.8V I2C operation. This patch adds
entry into devicetree.cb to set I2C port 4 operate at 1.8V.
Branch=None
Bug=chrome-os-partner:47821
Test=Built & booted kunimitsu board. Verified that I2C
port 4 is operating at 1.8V level
CQ-DEPEND=CL:*242225, CL:*241206, CL:315167
Change-Id: Ida69b885737aef0cfcf6a6ca21b3650169e614d9
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 990df9c1c65e75aae0a1329ead3790e78021b804
Original-Change-Id: Ifbb65e3d83561b52cc18e48b89d146c2f88f289b
Original-Signed-off-by: Naresh G Solanki <Naresh.Solanki@intel.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/315168
Original-Commit-Ready: Naresh Solanki <naresh.solanki@intel.com>
Original-Tested-by: Robbie Zhang <robbie.zhang@intel.com>
Original-Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/13010
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
- Enable serial irq configuration in FSP.
- Set minimum assertion width values for FSP to configure.
- Set I2C4 voltage to 1.8V.
- Enable SaGv feature to dynamically train memory frequency.
BUG=chrome-os-partner:47688
BRANCH=none
TEST=build and boot on chell EVT
Change-Id: If6955c9ee4f08d1ebc6e98e0ba0786073919856f
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 7403149299ec2c6c66c2066a5dd8294608e71409
Original-Change-Id: Ia182396ad4eb7a283e183fce7c50c98f6d2de57c
Original-Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/321212
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/13009
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
- Enable serial irq configuration in FSP.
- Set minimum assertion width values for FSP to configure.
- Set I2C4 voltage to 1.8V.
- Enable SaGv feature to dynamically train memory frequency.
- Disable Deep S3 to match chell so DeepSx story is consistent
on skylake-y boards.
BUG=chrome-os-partner:47688
BRANCH=none
TEST=emerge-glados coreboot (tested on chell board)
Change-Id: Ied6bda6a3f2108df7167e0970abe71977d8d2a5c
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: fbf353288edc9629ad03b17d0a582e3042d5a5e1
Original-Change-Id: I1619dd5316060793f38b74f8f0bcaf23d8ab2552
Original-Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/321211
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/13008
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
The keyboard backlight is very bright at 100% so be more
subtle when turning it on at boot time.
BUG=chrome-os-partner:40635
BRANCH=none
TEST=build and boot on chell EVT
Change-Id: I3925b94b4a455eb7d3bbb6eee414d21cf6d3bb93
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 52da1456527bfa6e0a3290c87c4886e2b3111e21
Original-Change-Id: Ia3412b4052c96f5de8e8aef59f69f6b346b9aca8
Original-Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/321210
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/13007
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
This patch adds an UPD/VPD parameter to set voltages to the
I2C ports individually via devicetree.cb
BRANCH=None
BUG=chrome-os-partner:47821
TEST=Tesed by setting voltage via devicetree.cb
and verified voltage level using a DSO probe.
CQ-DEPEND=CL:*242225, CL:*241206
Change-Id: Iaeb1ab3f9724aa1139c876dc63250469661d8439
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: fc73b98529ad1eb187f97a4177beda4224f473d1
Original-Change-Id: Ib477ad26667ef59cd298b5e20a68a8c68d85bd8d
Original-Signed-off-by: Naresh G Solanki <Naresh.Solanki@intel.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/315167
Original-Commit-Ready: Naresh Solanki <naresh.solanki@intel.com>
Original-Tested-by: Naresh Solanki <naresh.solanki@intel.com>
Original-Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/13006
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Below are the correct RCOMP Target Values:
Samsung K4E6E304EB part = {100, 40, 40, 21, 40}
The rest of the DIMMs should have RCOMP set to
{100, 40, 40, 23, 40}
LARs EVT has new DIMM configurations, and the earlier RCOMP
settings are not correct for the newly added DIMM cards,
causing reboot issues.
With this patch all the DIMMs get the required values programmed.
BRANCH=None
BUG=None
TEST=Built for Lars EVT SKU1/2/3 and verified Boot to OS.
No Reboot after this change.
Change-Id: I5fa5ce47b4b47198b0ae8d0b57f7729cb57d23bf
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: d29cc8a4ad9bc2b7680e4df146ce281738e4a3c4
Original-Change-Id: I15195b748213553907ff22dbc74651d70f3c7bb6
Original-Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/320527
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/13005
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Kingston eMMC can now run under HS400 mode.
BUG=chrome-os-partner:48017
BRANCH=none
TEST=run consecutive boot 100 times on Lars proto Kingston SKU, and
MMC errors didn't happen.
Change-Id: I3c16db6111273fbbabbfba1c315edc780fe23525
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: ac474bd7bd33f11904a27691e9eb61bdaf212c6b
Original-Change-Id: I9e47b6ba64ac94acff7673fca86fa62bfb30edd9
Original-Signed-off-by: David Wu <David_Wu@quantatw.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/320194
Original-Commit-Ready: David Wu <david_wu@quantatw.com>
Original-Tested-by: David Wu <david_wu@quantatw.com>
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Original-Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/13004
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Hynix eMMC can now run under HS400 mode.
BUG=chrome-os-partner:47647
TEST=run consective boot 100 times on Chell EVT Hynix SKU, and
MMC errors didn't happen.
BRANCH=none
Change-Id: Icb6fc03d0510d2c5aeb5b08ed7189e954ab39a72
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 9966c430a508a13cf1a617f485a48866bec161ca
Original-Change-Id: I6bec88f5c2813131a693ddba5523a9d43b2ebd45
Original-Signed-off-by: Ryan Lin <ryan.lin@intel.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/319627
Original-Commit-Ready: Duncan Laurie <dlaurie@chromium.org>
Original-Tested-by: Duncan Laurie <dlaurie@chromium.org>
Original-Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/13003
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
This change enables SaGv feature for skylake
platform. As a result of this patch the skylake
platform will train memory at both low & high
frequency points. This will be used to
dynamically scale the work point
(voltage/frequencies).
The value "3" here means enable. Following
is the table for same.
0=Disabled (SaGv disabled)
1=FixedLow (Fixed to low frequency)
2=FixedHigh (Fixed to High frequency)
3=Enabled( SaGv Enabled.Dynamically changes)
BRANCH=None
BUG=chrome-os-partner:48534
TEST=Build and boot lars
Change-Id: I82b1a428d2d3dce47f46de576f677cf2249b6b5d
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 8e252123cc73543d0f1b320af9d8873f99a45ab1
Original-Change-Id: I1a545ff2f38df23964378c0d833e29006b2c5557
Original-Signed-off-by: David Wu <David_Wu@quantatw.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/320022
Original-Commit-Ready: David Wu <david_wu@quantatw.com>
Original-Tested-by: David Wu <david_wu@quantatw.com>
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Original-Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Original-Reviewed-by: Haridhar Kalvala <haridhar.kalvala@intel.com>
Reviewed-on: https://review.coreboot.org/13002
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
If the system is in recovery don't bother saving MRC training data.
BRANCH=None
BUG=chrome-os-partner:48534
TEST=Built for kunimitsu.
Results show MRC data is not saved
in recovery mode.
Change-Id: I236b7fe1860ac86722562c9a749067496dfe98f8
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: acca68bb5fece58549d762bfaef3e9f2eb0d3066
Original-Change-Id: Idb0cd7d7c789a58d05160968f6448cb59882056c
Original-Signed-off-by: haridhar <haridhar.kalvala@intel.com>
Original-Signed-off-by: Somayaji, Vishwanath <vishwanath.somayaji@intel.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/319221
Original-Commit-Ready: Haridhar Kalvala <haridhar.kalvala@intel.com>
Original-Tested-by: Haridhar Kalvala <haridhar.kalvala@intel.com>
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Original-Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Original-Reviewed-by: Haridhar Kalvala <haridhar.kalvala@intel.com>
Reviewed-on: https://review.coreboot.org/13001
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
MP init is already handled in coreboot, but it is also part of FSP
FSP has a implemented a provision to allow FSP to skip MP init and
let coreboot handle it.
BRANCH=none
BUG=chrome-os-partner:44805
TEST=Build and booted in kunimitsu with SkipMpInit enabled from CB.
CQ-DEPEND=CL:310192
Change-Id: Idd9b1424f23765ce227005a322ac72d9e9fc841a
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 5c52d0f0cc5d480c87fababc3316009e3ade6e45
Original-Change-Id: I9d92046d0237680b8d562814a9a605a36efb9516
Original-Signed-off-by: Barnali Sarkar <barnali.sarkar@intel.com>
Original-Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/312926
Original-Commit-Ready: Preetham Chandrian <preetham.chandrian@intel.com>
Original-Tested-by: Preetham Chandrian <preetham.chandrian@intel.com>
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/12992
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
MP init is already handled in coreboot, but it is also part of FSP
FSP has a implemented a provision to allow FSP to skip MP init and
let coreboot handle it.
BRANCH=none
BUG=chrome-os-partner:44805
TEST=none
CQ-DEPEND=CL:319353
Change-Id: I22c1add182b299e2ad9d413bc13c5a5acc6a3179
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: ccf89c9d1fe18b74c385e7d12a6aef5b63d7b243
Original-Change-Id: I53b754fd10a140588ad67d9292d9bc04a6d43677
Original-Signed-off-by: Barnali Sarkar <barnali.sarkar@intel.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/319194
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/13000
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
MP init is already handled in coreboot, but it is also part of FSP
FSP has a implemented a provision to allow FSP to skip MP init and
let coreboot handle it.
BRANCH=none
BUG=chrome-os-partner:44805
TEST=Build and booted in Lars with SkipMpInit enabled from CB
CQ-DEPEND=CL:319353
Change-Id: Ib35d9072b883592d22466dfeb1fd45403c0479d4
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 91cf59ea7865568eca2ce242d81c4c486076d5ac
Original-Change-Id: Ibb46fc6bc7e862c9ea8bc9f9b0d508c3707282a2
Original-Signed-off-by: Barnali Sarkar <barnali.sarkar@intel.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/319257
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/12999
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
This patch disables the SaGv feature in recovery mode. Since the memory
training happens at both low and high frequency points when SaGv is
enabled, recovery mode boot time increases by 5 seconds. To reduce this
5 second increase, the SaGv feature is disabled in recovery mode.
The value "0" here means SaGv disable.
Following is the table for same.
0=Disabled (SaGv disabled)
1=FixedLow (Fixed to low frequency)
2=FixedHigh (Fixed to High frequency)
3=Enabled (SaGv Enabled. Dynamically changes)
BRANCH=None
BUG=chrome-os-partner:48534
TEST=Built for kunimitsu.
Results show recovery mode boot time
is not affected (not increased).
Change-Id: I77412a73a183a5dbecf5564a22acc6e63865123e
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: dc586079052acf9af573b68dff910386cd43484d
Original-Change-Id: Ice3e1a630e119d40d3df52e3a53ca984e999ab0b
Original-Signed-off-by: haridhar <haridhar.kalvala@intel.com>
Original-Signed-off-by: Somayaji, Vishwanath <vishwanath.somayaji@intel.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/315759
Original-Commit-Ready: Haridhar Kalvala <haridhar.kalvala@intel.com>
Original-Tested-by: Haridhar Kalvala <haridhar.kalvala@intel.com>
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Original-Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Original-Reviewed-by: Haridhar Kalvala <haridhar.kalvala@intel.com>
Reviewed-on: https://review.coreboot.org/12998
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
This change enables SaGv feature for skylake
platform.As a result of this patch the skylake
platform will train memory at both low & high
frequency points.This will be used to
dynamically scale the work point
(voltage/frequencies).
The value "3" here means enable. Following
is the table for same.
0=Disabled(SaGv disabled)
1=FixedLow(Fixed to low frequency)
2=FixedHigh(Fixed to High frequency)
3=Enabled(SaGv Enabled.Dynamically changes)
BRANCH=None
BUG=chrome-os-partner:48534
TEST=Built for kunimitsu.
Tested on D1 silicon.
Change-Id: I2892d631d64495e6aed453af4fd526f4bf5bed68
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 8e09d1a22927f5fcddd6c0be3f9edf3dcb8729be
Original-Change-Id: I32a7a53805068a52b381affaf061d69062cd8651
Original-Signed-off-by: haridhar <haridhar.kalvala@intel.com>
Original-Signed-off-by: Somayaji, Vishwanath <vishwanath.somayaji@intel.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/315806
Original-Commit-Ready: Haridhar Kalvala <haridhar.kalvala@intel.com>
Original-Tested-by: Haridhar Kalvala <haridhar.kalvala@intel.com>
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Original-Reviewed-by: Haridhar Kalvala <haridhar.kalvala@intel.com>
Reviewed-on: https://review.coreboot.org/12997
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Update Memory IDs for EVT board
BUG=None
BRANCH=lars
TEST=Build and boot lars
Change-Id: I8c0c731fc3a8eec0cb558137e9db90170debf2c6
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: a95fbf063b2e41d551171228a1ea8cbcfdcaecc8
Original-Change-Id: I2be8a7db99f17ea2968d7e4c5de83cc3e4cbcd14
Original-Signed-off-by: David Wu <David_Wu@quantatw.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/319622
Original-Commit-Ready: David Wu <david_wu@quantatw.com>
Original-Tested-by: David Wu <david_wu@quantatw.com>
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/12996
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Functions in file pcie.c is not needed.
TEST=Boot and test wifi and video playback
Original-Reviewed-on: https://chromium-review.googlesource.com/298965
Original-Tested-by: Hannah Williams <hannah.williams@intel.com>
Original-Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Change-Id: I70337c0fc61c221330836ef17f6cefea8c5f0f11
Signed-off-by: Shaunak Saha <shaunak.saha@intel.com>
Reviewed-on: https://review.coreboot.org/12737
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
SSM4567 smart speaker needs Current and Voltage sensing to be
captured and reported to the algorithm.
This needs 4 CH capture blob.
BUG=chrome-os-partner:48625
BRANCH=none
TEST=Built and booted. Verified CBFS locates
the blob.
CQ-DEPEND=CL:*242635
Change-Id: Ie13622da9a9a8ce5930d32e52ddaf2e0d4862895
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 06f1a501dcb3fa6102eccdb3e24f9011b7869ab0
Original-Change-Id: I7b65b7582b619be53544ebbe4b3ea65398d32a34
Original-Signed-off-by: Sathya Prakash M R <sathya.prakash.m.r@intel.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/319020
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/12995
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
No functional changes - just whitespace fixes.
Signed-off-by: Martin Roth <martinroth@google.com>
Change-Id: I8ffa87240bcbd3d657ed9dc619b5e5bf9de734d7
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/12853
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
All of the yabel files are BSD licensed.
Change-Id: Ibe0b3bb67a96c57b5d693676f5e8f19b6bed90fa
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/12972
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Fixes bug that decode_pciebar() function was bypassed due
to PCI_DEV(0,0,0) being detected as zero and function returning 0.
Change-Id: Ia79bcebbe3ba36f479cbb24dbbb163a031d9c099
Signed-off-by: Damien Zammit <damien@zamaudio.com>
Reviewed-on: https://review.coreboot.org/13031
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Vladimir Serbinenko <phcoder@gmail.com>
|
|
MP init is already handled in coreboot, but it is also part of FSP.
FSP has a implemented a provision to allow FSP to skip MP init and
let coreboot handle it.
BRANCH=none
BUG=chrome-os-partner:44805
TEST=none
CQ-DEPEND=CL:319353
Change-Id: I81c54582a3c980ecdcf329347bcd5982802d681c
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: e60ee81acaeb1062a31a3e78ed2ba4ccfe816ec5
Original-Change-Id: I71dd07559dffb7886e489274ffc8e71686ca730f
Original-Signed-off-by: Barnali Sarkar <barnali.sarkar@intel.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/319370
Original-Commit-Ready: Preetham Chandrian <preetham.chandrian@intel.com>
Original-Tested-by: Preetham Chandrian <preetham.chandrian@intel.com>
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/12994
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Changing the UPD param name from "SkipMpInit" to "FspSkipMpInit"
BRANCH=none
BUG=none
TEST=Build and booted in kunimitsu with FspSkipMpInit token
enabled from Coreboot.
Change-Id: I5ebe7a1338ac77a62d5aa2e48e083b4fb906bf28
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: cdaa95a82bc7e90637c6b90e33d88d040e085f58
Original-Change-Id: Ibdaa3d202f8f6f6f0ca6c6d4c6428f1616572f1d
Original-Signed-off-by: Barnali Sarkar <barnali.sarkar@intel.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/319353
Original-Commit-Ready: Preetham Chandrian <preetham.chandrian@intel.com>
Original-Tested-by: Preetham Chandrian <preetham.chandrian@intel.com>
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/12993
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Lars has an ambient light sensor connected to the EC which
is presented to the OS as a standard ACPI0008 device.
BUG=none
BRANCH=none
TEST=emerge-lars coreboot
Change-Id: I406b634176dac3f4cf1894e6b386af3306d11ffa
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 37d96458a11c33899f210cc04d3bdab07ec18746
Original-Change-Id: I017aeed1a8684676557e483ffa895dc4bb125d26
Original-Signed-off-by: David Wu <David_Wu@quantatw.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/319364
Original-Commit-Ready: David Wu <david_wu@quantatw.com>
Original-Tested-by: David Wu <david_wu@quantatw.com>
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/12990
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
BRANCH=lars
BUG=None
TEST=alt+f6, alt+f7
Change-Id: I20d44ae806facf7470ab50d7b9ca4f36404b6ea3
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 3bf8c26a11e632cc9f4112eace813478fb7ff8ca
Original-Change-Id: Iaa59818f5d2d17eb6759cefa9b6fbfba82bb2fca
Original-Signed-off-by: David Wu <David_Wu@quantatw.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/319270
Original-Commit-Ready: David Wu <david_wu@quantatw.com>
Original-Tested-by: David Wu <david_wu@quantatw.com>
Original-Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/12989
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
The BOOT_BEEP gpio is used to activate the buffer which
isolates the I2S signals from PCH while doing a beep from depthcharge.
It needs to be lo to deactivate the buffer for audio playback from OS.
BUG=chrome-os-partner:47124
BRANCH=None
TEST=boot depthcharge & test beep with devbeep.
Boot OS and test audio playback.
Change-Id: I047513f6cbe9590820dfe3c369161a157864be97
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: d0e04d6792a4511630b8111d0f4a64226042f3e6
Original-Change-Id: I0fa8f425ac413798740343823d026c6300c8eef1
Original-Signed-off-by: Rohit Ainapure <rohit.m.ainapure@intel.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/319220
Original-Commit-Ready: Rohit M Ainapure <rohit.m.ainapure@intel.com>
Original-Tested-by: Michael Rang <michael.rang@intel.com>
Original-Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/12988
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
The timestamps and post codes for the beginning of the FspNotify calls
are out of order. Reverse these entries to fix this error.
BRANCH=none
BUG=None
TEST=Build and run on kunimitsu
Change-Id: Ibfa1ba4b07e31bf3823469ac2dc7deaa8c67deab
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 3cd63c56c59337f0ff58fd11a78d08352cf6a04a
Original-Change-Id: I4627860d3ebf446523a5662dbbc8e59153441945
Original-Signed-off-by: Lee Leahy <Leroy.P.Leahy@intel.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/318903
Original-Commit-Ready: Leroy P Leahy <leroy.p.leahy@intel.com>
Original-Tested-by: Leroy P Leahy <leroy.p.leahy@intel.com>
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/12987
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
The GPU panel configuration variables are unused on skylake
and are no longer needed in chip.h.
BUG=chrome-os-partner:40635
BRANCH=none
TEST=emerge-chell coreboot
Change-Id: Ie6bfb676b5a32b4d4d39dda91b90fc7e973d38e0
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: f261d7ca9ec93aae1362975efde11ac9657b7ca6
Original-Change-Id: If64594455754e4dea1f53511861b74ddd880c5b5
Original-Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/318923
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/12986
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Use the Kunimitsu settings as baseline, except Psi4Enable set to 0 due
to a known issue (not able to hit S0ix) on glados. The VR settings will
then need to be updated per the board VR design.
BRANCH=none
BUG=chrome-os-partner:48466
TEST=Build and booted chell
Change-Id: Ieb014e2a0cee1cb02a1c095da273b5ac1a19ef5d
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: fcd47a2fb2b369a93d2992fa1c17c2ce91c0e948
Original-Change-Id: Iac197314702fe5897359afc1ad1636bbcdafa204
Original-Signed-off-by: robbie zhang <robbie.zhang@intel.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/317870
Original-Commit-Ready: Aaron Durbin <adurbin@chromium.org>
Original-Tested-by: Aaron Durbin <adurbin@chromium.org>
Original-Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/12985
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Use the Kunimitsu settings as baseline, except Psi4Enable set to 0 due
to a known issue (not able to hit S0ix) on glados. The VR settings will
then need to be updated per the board VR design.
BRANCH=none
BUG=chrome-os-partner:48466
TEST=Build and booted glados
Change-Id: I42d360657ab7c47d66043f39b79540b69a9072d1
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: d06397c1c32136d1b6a1c1346ed722ad6926ce1a
Original-Change-Id: Ib0746cd84c2c8af29f53a65a0a7b85966c918869
Original-Signed-off-by: robbie zhang <robbie.zhang@intel.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/317910
Original-Commit-Ready: Aaron Durbin <adurbin@chromium.org>
Original-Tested-by: Aaron Durbin <adurbin@chromium.org>
Original-Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/12984
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
FSP 1.8.0 will do nothing with the VR settings if VrConfigEnable is
non-zero. That behavior is not desired because it's not clear what
the behavior will be for various processor SKUs. Instead provide
default values for the VR config. Note that PSI3 and PSI4 are not
enabled for those defaults.
BUG=chrome-os-partner:48466
BRANCH=None
TEST=Built and booted glados.
Change-Id: I02cb5fbdd4549cc827a0b0e4006bc21da4593b55
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: a68c53e0fdf15584270dfafc679a22319f497d17
Original-Change-Id: I82b1d1da2cfa3c83ccc6a981e30ffac6fb6c8c4b
Original-Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/318263
Original-Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/12983
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Copy changes from chell to add 20K pull-up to LPC address lines
and setup the PCH_WP signal early so it is set correctly in VBNV.
BUG=chrome-os-partner:40635
BRANCH=none
TEST=emerge-glados coreboot
Change-Id: I3337cb9e5ee445471c7a0b61ee22869f66189b63
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: c99dae3729636790c2ad457ec3271d2bd99fb1c4
Original-Change-Id: I7627ec263e710ce186cea15c805203395acf3e99
Original-Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/317244
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/12982
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
There is a UPD setting exposed by FSP that allows the DDR
frequency to be limited. Expose this for devicetree.
BUG=chrome-os-partner:47346
BRANCH=none
TEST=tested by limiting DDR frequency to 1600 on chell EVT
Change-Id: I1f17b221d9fa4c2dd1e8c5f403deb0f2bc0493a7
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 91f760ad19823225f7e5bd2dc690164ed253e220
Original-Change-Id: Ibcd4a65a9cfd7d32fbf2ba8843ab25da8e9cf28a
Original-Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/317243
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/12981
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
The THERMTRIP status bit is in GBLRST_CAUSE instead of
GEN_PMCON like the EDSv1 indicates. Read this status bit
and add an elog event if THERMTRIP has fired.
BUG=chrome-os-partner:48438
BRANCH=none
TEST=tested on chell EVT after thermtrip fired
Change-Id: Icd52b753c7f3ab0d48095279f1255dd2dd08fd59
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: b090c7897a8f99a685f523990235d83fafa063b2
Original-Change-Id: I5a287d7fdae2ba8ae8585cb9a4d4dd873393e1e6
Original-Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/317242
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/12980
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
- Add pullup on LPC address lines for leakage
- Configure PCH_WP early so it gets set properly in VBNV
- Disable SD card reader in favor of USB
BUG=chrome-os-partner:47346
BRANCH=none
TEST=build and boot on chell EVT
Change-Id: Ibac79c6cbef0515b1e8a513cfde5fee184e4c70a
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: ebd0c16a6009b74d3c6c36878c502fda9bb3020d
Original-Change-Id: If2bc4eb546a1aab50d3688b6e92f8c38214c9cca
Original-Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/317241
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/12979
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Follow kunimitsu setting of
https://chromium-review.googlesource.com/#/c/313068/
BRANCH=none
BUG=chrome-os-partner:48459
TEST=Build and boot in lars
Change-Id: Iffa9e1307f478b1d72befd3e5af71e7d40bb55ef
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 6c669014d0773d6790656dd6f957d2c860d00781
Original-Change-Id: I615d53a33ad8e750d4382e2a9ec397c5b6ff55e1
Original-Signed-off-by: David Wu <David_Wu@quantatw.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/317222
Original-Commit-Ready: David Wu <david_wu@quantatw.com>
Original-Tested-by: David Wu <david_wu@quantatw.com>
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/12978
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
The write protect GPIO is not being configured early enough.
This is leading to coreboot reading incorrect value, and
writing the incorrect value in vboot shared file.
This is leading to "crossystem wpsw_boot" always returning 0
even with the write protect screw in place during boot.
BRANCH=none
BUG=chrome-os-partner:48292
TEST=Build and boot on lars
Change-Id: I28fbbd690ca6efb539422e9ba02f10e07cd35346
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: d229ba9d8934dcb5f22b27ce0ad27601ec87d6ff
Original-Change-Id: I64f2497a6bb3a50b0f58c67e2ab6751c4836fd89
Original-Signed-off-by: David Wu <David_Wu@quantatw.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/317130
Original-Commit-Ready: David Wu <david_wu@quantatw.com>
Original-Tested-by: David Wu <david_wu@quantatw.com>
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/12966
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
The HeciEnabled decides the state of Heci1 at end of boot. Setting to 0
(default) disables Heci1 and hides the device from OS. It internally uses
the FSP Psf Unlock policy to disable the Heci1. It also adds the p2sb
device in the devicetree which is necessary for hiding and unhiding the
device.
BRANCH=none
BUG=chrome-os-partner:45618
TEST=build for kunimitsu.
CQ-DEPEND=CL:*238451
Change-Id: Ieba2ab3b4ac518cce8371069028170ba99aaf079
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: cbefe9d6e9a981594534d346be67a5cd94483d05
Original-Change-Id: I8c95b5b9b28ba8441ca031f4e9ec523d913990d6
Original-Signed-off-by: Archana Patni <archana.patni@intel.com>
Original-Signed-off-by: Subramony Sesha <subramony.sesha@intel.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/311913
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/12977
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
This just updates existing guard name comments on the header files
to match the actual #define name.
As a side effect, if there was no newline at the end of these files,
one was added.
Change-Id: Ia2cd8057f2b1ceb0fa1b946e85e0c16a327a04d7
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/12900
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
These were copied from the linux kernel, so get the standard corboot GPL
v2 header.
Change-Id: I27ef3326cc42b7e005f94c8b4fd355012a89561d
Signed-off-by: Damien Roth <yves.r.roth@gmail.com>
Reviewed-on: https://review.coreboot.org/13023
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
These files are original to coreboot and get the standard
coreboot GPL header.
Change-Id: I19565b0d2424a6f37a95ab4d7b16742d23122d1e
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/12919
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Most of these files are original to coreboot and get the standard
coreboot GPL header.
encoding.h and atomic.h are from the riscv codebase and have their
license.
Change-Id: I32506b0ecf88be2f5794dc1e312a6cd9b2a271ad
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/12906
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
This was breaking the build on OS X, but also wasn't working correctly
under linux anymore either. It wouldn't print the illegal symbols
when it failed.
- Split the generation of the offenders file from the actual check for
offending symbols and just send all output to /dev/null.
- Rewrite the check for offending symbols in a way that works with OS X.
Tested by adding a global variable to romstage and verifying the
failure is shown correctly. Verified that it works correctly with no
illegal variables.
Change-Id: I5b3ac32448851884d78c3b3449508ffe014119ab
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/13018
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
This patch power gates the Kepler module
on skylake kunimitsu board. This is required
to save power since this is consuming over 500mw
of power in all active use cases.
The device can be powered on later by using the
kernel driver as required by setting the
kepler enable gpio high.
BRANCH=None
BUG=chrome-os-partner:45962
TEST=Build and Boot Kunimitsu and check lspci.
The Kepler device should not be listed.
Also power measurement of board should give
approximately 300mW of reduction in power.
Change-Id: I244a23385e20ef1431dc895536c8a47e1f5770d7
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 8d4fb7d01f32ac307a351c307b8461628c0e5414
Original-Change-Id: Idafa74d7ff14d67a5b1e635f783efd84b5a7399c
Original-Signed-off-by: Pravin Angolkar <pravin.k.angolkar@intel.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/302277
Original-Commit-Ready: Naveenkrishna Ch <naveenkrishna.ch@intel.com>
Original-Tested-by: Pravin K Angolkar <pravin.k.angolkar@intel.com>
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/12964
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Enable the config option for TPM to use PIRQ instead of SERIRQ
and enable the MAINBOARD_HAS_LPC_TPM option.
BUG=chrome-os-partner:46335
BRANCH=none
TEST=tested this patch with TPM ACPI driver(tpm_tis.force=0)
Change-Id: I311cc7d2e70cc52a7e90f3c3c60d422b7b998789
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: ad9450c342c752f87e3385a2acd5dd79b65cc75f
Original-Change-Id: Ib7b1b40c296fce80d5366bd19e7ff20d7161db95
Original-Signed-off-by: Rishavnath Satapathy <rishavnath.satapathy@intel.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/316287
Original-Commit-Ready: Pravin K Angolkar <pravin.k.angolkar@intel.com>
Original-Commit-Ready: Naveenkrishna Ch <naveenkrishna.ch@intel.com>
Original-Tested-by: Pravin K Angolkar <pravin.k.angolkar@intel.com>
Original-Reviewed-by: Pravin K Angolkar <pravin.k.angolkar@intel.com>
Original-Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/12963
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Provide an option for including the NHLT blobs within the
kunimitsu mainboard directory while also adding the ACPI NHLT
table generation that the current hardware supports.
Kunimitsu does support two audio codec, ADI and MAXIM,
hence use AUDIO_DB_ID to read correct codec and craete
NHLT table, this will also help to load only one amplifier ASL
for machine driver consumption.
BUG=chrome-os-partner:44481
BRANCH=None
TEST=Built and booted kunimitsu board. Audio worked
with both ADI and MAXIM audio card.
CQ-DEPEND=CL:316352
Change-Id: Ic9b9af83a0229fdf5f1cb019245ae65ad9d2f06c
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 2db85062d65c5e831da297588aa4abb18d6ed1bb
Original-Change-Id: I3b08f3f23b334799a81cde81a30d6f231cc8583f
Original-Signed-off-by: Naresh G Solanki <Naresh.Solanki@intel.com>
Original-Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/315450
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/12959
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
This patch adds support for disabling the heci1 device
at the end of boot sequence. Prior to this, FSP would have
sent the end of post message to ME and initiated the d0i3 bit.
This uses the Psf unlock policy and the p2sb device to disable
the heci1 device, then lock the configuration and hide the device.
BRANCH=none
BUG=chrome-os-partner:45618
TEST=build for kunimitsu or glados board. set the hecienabled policy
to 0 and check for heci 1 device status in kernel lspci.
CQ-DEPEND=CL:*238451
Change-Id: I26b145231f8ed0c140af42d378b222e857d9aff6
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: fe184b8baf1bea9bcd0af1841785a4d763af9358
Original-Change-Id: I3b435491aeea0f2ca36b7877e942dc940560e4dd
Original-Signed-off-by: Archana Patni <archana.patni@intel.com>
Original-Signed-off-by: Subramony Sesha <subramony.sesha@intel.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/311912
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/12976
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
CB used to clear recovery status towards romstage end after FSP
memory init. Later inside FSP silicon init due to HSIO CRC mismatch
it will request for an additional reset.On next boot system resume
in dev mode rather than recovery because lost its original state
due to FSP silicon init reset.
Hence an additional 1 reset require to identify original state.
With this patch, we will get future platform reset info during romstage
and restore back recovery request flag so, in next boot CB can maintain
its original status and avoid 1 extra reboot.
BUG=chrome-os-partner:43517
BRANCH=none
TEST= build and booted Kunimitsu and tested RO mode
Change-Id: Ibf86ff2b140cd9ad259eb39987d78177535cd975
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 40ddc21a97b318510116b7d5c4314380778a40f7
Original-Change-Id: Ia52835f87ef580317e91931aee5dd0119dea8111
Original-Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/302257
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/12975
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Enable the config option for TPM to use PIRQ instead of SERIRQ
and enable the MAINBOARD_HAS_LPC_TPM option.
BUG=none
BRANCH=none
TEST=tested this patch with TPM ACPI driver(tpm_tis.force=0)
Change-Id: I761d623d1064b8030f2703500d174259bb20ca79
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 2f7bdb1091b7dd62a3c0b4a2272ab9f56fd7acc9
Original-Change-Id: Id1a867980d2e28a1f328aa36bed3c846b2137bec
Original-Signed-off-by: David Wu <David_Wu@quantatw.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/317471
Original-Commit-Ready: David Wu <david_wu@quantatw.com>
Original-Tested-by: David Wu <david_wu@quantatw.com>
Original-Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/12974
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
At S0, S0ix and S3 LPC LAD signals are
floated at 400~500mV.
BRANCH=none
BUG=chrome-os-partner:48331
TEST=Build and boot on lars
Change-Id: I5582007e5caaf444740fa71c9761c27614aafee2
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: b855fd5834056a3f7d4aef91d634066006990a38
Original-Change-Id: I3a54f9f83f055e433cc1fea38169437ee7f9188f
Original-Signed-off-by: David Wu <David_Wu@quantatw.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/317071
Original-Commit-Ready: David Wu <david_wu@quantatw.com>
Original-Tested-by: David Wu <david_wu@quantatw.com>
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/12965
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Count DIMMs on current memory channel instead of all memory channels.
The current code is only able to correctly handle the following memory
configurations:
One DIMM installed in either channel.
Four DIMMs installed, two in each channel.
Two DIMMs installed, both in the same channel.
For systems that have any other configuration the DRAM On-Die-Termination
setting is wrong.
For example:
Two DIMMs installed, one in each channel.
Test system:
* Gigabyte GA-B75M-D3H (Intel Pentium CPU G2130)
Change-Id: I0e8e1a47a2c33a326926c6aac1ec4d8ffaf57bb6
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/12892
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@googlemail.com>
|
|
Remove the WakeConfigWolEnableOverride to disable WOL override
configuration in the General PM Configuration B (GEN_PMCON_B) register
BRANCH=none
BUG=none
TEST=Build and boot on lars
Change-Id: I48d3b706517b6ea6bda44800f61bb11da64503fb
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: eab69f2d725df739e5e0e5901a581ad58732cdf9
Original-Change-Id: I42c5a87150638171526ee67f194c1cd9d155203b
Original-Signed-off-by: David Wu <David_Wu@quantatw.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/317080
Original-Commit-Ready: Nicolas Boichat <drinkcat@chromium.org>
Original-Tested-by: David Wu <david_wu@quantatw.com>
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/12962
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Provide an option for including the NHLT blobs within the
lars mainboard directory while also adding the ACPI NHLT
table generation that the current hardware supports.
BUG=chrome-os-partner:44481
BRANCH=None
TEST=Built and booted lars board.
Audio worked with MAXIM audio card.
Change-Id: I1b7836c685ebbe1498f3dbaa2eb64d5e0d4faabb
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 401f1a7b23dca19712517ed1588e1390769d1271
Original-Change-Id: I6a937872a9e10d2c5ea15d5952d23e98416df092
Original-Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/316092
Original-Commit-Ready: Nicolas Boichat <drinkcat@chromium.org>
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/12961
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
This corresponds with the changes that have already gone into the
soc/intel/skylake chip.h file and is needed to get skylake platforms
building again.
Change-Id: I15bfee4eff50d6632659953ec8f97a39d8810db3
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/13022
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
I don't think the warning is valid, because we already verify
that num_channels is 2 or 4 as soon as we enter the function.
Adding the default case makes the compiler happy.
Fixes warning:
src/soc/intel/skylake/nhlt/dmic.c: In function 'nhlt_soc_add_dmic_array':
src/soc/intel/skylake/nhlt/dmic.c:100:2: error: 'formats' may be used
uninitialized in this function [-Werror=maybe-uninitialized]
return nhlt_endpoint_add_formats(endp, formats, num_formats);
^
Change-Id: Idc22c8478ff666af8915d780d7553909c3163690
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/13021
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Make sure the latest & greatest Intel targets actually
build in our build system.
intel/sklrvp is still failing for reasons unrelated to the rest
of the skylake boards. Leaving that disabled for now.
Change-Id: Ie784628a57257cea30e5e47074648198b884f6db
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/12857
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Tested-by: build bot (Jenkins)
|
|
remove the WakeConfigWolEnableOverride to disable WOL override
configuration in the General PM Configuration B (GEN_PMCON_B) register
BRANCH=none
BUG=none
TEST=Build and booted in kunimitsu
Change-Id: Ia523e7956c06c9f4a60e0a2296f771cc3c70bc25
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 12a07eebfb8fa4ee8013fbbb12283a0b429cacfd
Original-Change-Id: I2be6c5b0114e4c7d8a7b9ceb59ee32f28f61769f
Original-Reviewed-on: https://chromium-review.googlesource.com/316717
Original-Commit-Ready: Rizwan Qureshi <rizwan.qureshi@intel.com>
Original-Tested-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/12958
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Follow kunimitsu setting of
https://chromium-review.googlesource.com/#/c/313309/
BRANCH=none
BUG=none
TEST=Build and boot on lars.
Change-Id: I77a4454b3702dc58dc70a7b981b25a656e97f534
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 9c390322b4c770a0206549257dd34d1ef1242cc3
Original-Change-Id: I612e799433a396a6cce5742adb6de72a305b5df1
Original-Signed-off-by: David Wu <David_Wu@quantatw.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/316270
Original-Commit-Ready: David Wu <david_wu@quantatw.com>
Original-Tested-by: David Wu <david_wu@quantatw.com>
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Original-Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/12954
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
LARs design don't have SD Connector over native SD Controller.
BUG=chrome-os-partner:48190
BRANCH=None
TEST=Build & boot LARs. Use "lspci" doesn't list 0x1E:06
device in list.
CQ-DEPEND=CL:315420
Change-Id: Idff7243a6aaf4b8d5f49e4bf215a77131f716485
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: ca769138b97b404598c4a6bfa6c2ff5c1c3ec896
Original-Change-Id: I71416ac89a8c91ab272d6737d1b46c8045567e17
Original-Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/315423
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/12947
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Skylake Core boot should have configurable option to skip
PCH based SD 3.0 Controller from customer/reference design.
Addition to that no unused or unnecessary should list under
device view.
BUG=chrome-os-partner:48190
BRANCH=None
TEST=Build & boot Kunimitsu and LARs.
Change-Id: Ie17fd6db01e0cabcdf605017509d809b54509a0d
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 99ac17b723125822368539d0562aa35119e520fb
Original-Change-Id: I98a48f45ef442246227fd54ea021b53f824954c5
Original-Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/315420
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/12946
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Cofigure VR settings for kunimitsu
BRANCH=none
BUG=chrome-os-partner:45387
TEST=Build and booted in kunimitsu
CQ-DEPEND=CL:311317
Change-Id: Ib2afe7694d2a807cea1befa73349bd21a3e7d909
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: c3548d7cb3a00826377e819f20d07167b4eb2c65
Original-Change-Id: I6b80f509bc0ab6f65f26eec0651a3b44fb38fbf9
Original-Signed-off-by: Barnali Sarkar <barnali.sarkar@intel.com>
Original-Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/313068
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/12945
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Adding VrConfig UPDs and assign values to those from devicetree
BRANCH=none
BUG=chrome-os-partner:45387
TEST=Build and booted in kunimitsu
CQ-DEPEND=CL:310192
Change-Id: Ifce9dfacabc742b55266c48459c56c69b1f22236
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: b34a3cc77afc8795abb64972f8169986c30c2acd
Original-Change-Id: Ifa960e718ed77db729f1fc4e2c00c9b305093e04
Original-Signed-off-by: Barnali Sarkar <barnali.sarkar@intel.com>
Original-Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/311317
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/12944
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins)
|
|
This patch helps to enable SkipMpInit token of FSP SiliconInit UPD
BRANCH=none
BUG=chrome-os-partner:44805
TEST=Build and booted in kunimitsu with SkipMpInit enabled from CB.
CQ-DEPEND=CL:310869
Change-Id: I43377e4b8adadf42091a9387883363fdfbab4c1b
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: b7962273fd1a591cfe9a658f49ebc7d23bcad577
Original-Change-Id: I977d2d39c283d74f1aa9033c8aa60dc652735019
Original-Signed-off-by: Barnali Sarkar <barnali.sarkar@intel.com>
Original-Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/310192
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/12943
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Even though the data32 variable was getting written by
pch_pcr_read(), GCC still flagged it as being used while
uninitialized and failed the build.
Note that pch_pcr_read() may only set 1 or 2 bytes of data32 in the
successful path, depending on the size of the read.
Change-Id: Icd6e80d06b9bf4af506d62d55ffe4c5e98634b2b
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/12860
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Ben Gardner <gardner.ben@gmail.com>
|
|
Tested on Intel D510MO
Before this patch, I was unable to get the SATA controller into AHCI
mode. That is, I could never see PCI ID 8086:27c1 appearing on the bus.
With sata_ahci set, controller now goes into AHCI mode and works. 8086:27c1
Tested on X60 with AHCI enabled 8086:27c5 (AHCI mode for mobile ich7)
No regressions detected.
Change-Id: I4a3eabb5773106a0825fa2f30ee400fbfe636c7f
Signed-off-by: Damien Zammit <damien@zamaudio.com>
Reviewed-on: https://review.coreboot.org/12923
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Add new configuration parameters eg. #SLP_S3 assert width
BRANCH=none
BUG=chrome-os-partner:44075
TEST=Build and booted on kunimitsu, verified that CB is doing
the Lockdowns which were previously done by FSP.
CQ-DEPEND=CL:310869
Change-Id: I782df49bbf73c121b191f0661907173c4fd29b64
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: de0742869b1b148597d3714a3bc29a0dc08642aa
Original-Change-Id: I2b4041cdc22a29e79d2ff7f2cc49f51f80da5567
Original-Reviewed-on: https://chromium-review.googlesource.com/313309
Original-Commit-Ready: Rizwan Qureshi <rizwan.qureshi@intel.com>
Original-Tested-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/12942
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Some more PCH Policy UPD Parameters are added in FSP.
Lockdown config moved from FSP to coreboot.
Removing settings in devicetree.cb which are zero.
BRANCH=none
BUG=none
TEST=Build and booted on kunimitsu, verified that CB is doing
the Lockdowns which were previously done by FSP.
CQ-DEPEND=CL:*237842, CL:310191
Change-Id: I3dcf3a5340f3c5ef2fece2de5390cde48db4d327
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: e8bdb35897b640d271adcaed266030367f060553
Original-Change-Id: Ia201672565c07b2e03d972b2718512cd4fcbb95c
Original-Signed-off-by: Barnali Sarkar <barnali.sarkar@intel.com>
Original-Signed-off-by: Naresh G Solanki <Naresh.Solanki@intel.com>
Original-Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/310869
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/12941
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins)
|
|
Some MemoryInit UPD parameters have been moved to
SiliconInit in FSP 1.8.0. This patch has the respective
changes in coreboot for this.
BRANCH=none
BUG=none
TEST=Build and booted in kunimitsu
CQ-DEPEND=CL:*237423, CL:*237424
Change-Id: Ic008d22f96fb5f14965e5b5db15e05fb39dd52d3
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 573c1d8325cd504213528030ecf99559402b5118
Original-Change-Id: I71b893aa7788519ed2ef15f3247945ffcbbbcf4d
Original-Signed-off-by: Barnali Sarkar <barnali.sarkar@intel.com>
Original-Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/310191
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/12940
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
At S0, S0ix and S3 LPC LAD signals are
are floated at 400~500mV.
BRANCH=chrome-os-partner:48331
BUG=None
TEST=Build and Boot kunimitsu
Change-Id: I2e2654ac89f8e0c8d6ab1af31d0bd5a0d4c43db8
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 6f4b902e220dcde73df56970208c45fe3148b70e
Original-Change-Id: I597d4816d09d0cfd9b0ec183a9273551aed8688a
Original-Signed-off-by: pchandri <preetham.chandrian@intel.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/316529
Original-Commit-Ready: Preetham Chandrian <preetham.chandrian@intel.com>
Original-Tested-by: Preetham Chandrian <preetham.chandrian@intel.com>
Original-Tested-by: Kyoung Il Kim <kyoung.il.kim@intel.com>
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Original-Reviewed-by: Preetham Chandrian <preetham.chandrian@intel.com>
Original-Reviewed-by: Pratikkumar V Prajapati <pratikkumar.v.prajapati@intel.com>
Original-Reviewed-by: Kyoung Il Kim <kyoung.il.kim@intel.com>
Reviewed-on: https://review.coreboot.org/12957
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
GPIO ASL APIs to get GPIO Value.
Need such APIs to read GPIO config settings.
Example: Kunimitsu need to read AUDIO_DB GPIO
to identify codec select.
BUG=chrome-os-partner:44481
BRANCH=none
TEST=build and boot on Kunimitsu.
Change-Id: If56bb7b3eae08e1949d372850a6426dfde5aadd0
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 4983ba835a8da2baf578b035ae482755983c1ecb
Original-Change-Id: Ia40d86c8d4b14857fa8822677b3f7d393a35b677
Original-Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/316352
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/12956
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
DPTF may power off the system when it starts if the CPU temp is >90C.
Since TJmax is 100C set the critical threshold to just below that value.
BRANCH=none
BUG=none
TEST=Build and boot on lars.
Change-Id: I3abf946ae09c3c691480e468d0c1d74730dc6c06
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 7c2230009edb840e88a20c2d8a87f942c09b6bf3
Original-Change-Id: Iee1a3596dbbe934f68637f012c02c078c3751eeb
Original-Signed-off-by: David Wu <David_Wu@quantatw.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/316102
Original-Commit-Ready: David Wu <david_wu@quantatw.com>
Original-Tested-by: David Wu <david_wu@quantatw.com>
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Original-Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/12955
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Disable kepler device, it is removed and was not used on proto anyway.
BUG=none
BRANCH=none
TEST=build and boot on lars proto
Change-Id: I137b82b8dca23f5b40adcc6a056e77a4ff54d4d5
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 44d63453a9b31331d13d05f8f86d4218af0f0aa1
Original-Change-Id: Ib0892bf93b1d0cda1c0143d2b16cd58aeda83131
Original-Signed-off-by: David Wu <David_Wu@quantatw.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/315950
Original-Commit-Ready: David Wu <david_wu@quantatw.com>
Original-Tested-by: David Wu <david_wu@quantatw.com>
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Original-Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/12950
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Adding support for Maxim 98357A audio amplifier.
Removed SSM4567 support from LARs.
BUG=chrome-os-partner:44481
BRANCH=None
TEST=Build & boot on LARs.
Verify audio playback works using MAXIM amplifiers.
Change-Id: I2cd8b20e936319b434017b6dd73d4739684d21d3
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 76cbc20826c884194a144f6b6bc644900e5d475d
Original-Change-Id: I1156096b6aa367c0b8d8e3952d92f0eb5cf2820f
Original-Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/314543
Original-Commit-Ready: Nicolas Boichat <drinkcat@chromium.org>
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/12960
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
The write protect GPIO is not being configured early enough.
This is leading to coreboot reading incorrect value, and
writing the incorrect value in vboot shared file.
This is leading to "crossystem wpsw_boot" always returning 0
even with the write protect screw in place during boot.
BUG=chrome-os-partner:48292
BRANCH=None
TEST=Boot with the write protect screw in place. Issue
crossystem wpsw_boot. It should show 1.
Change-Id: I3a333a4dcce31be9afe28cf11b127090cc7b9421
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 462dd0229c2d3b81cd34bdd2e36bea844f58586c
Original-Change-Id: Ib7e0539845575b32322e243e89b81ffee077eb81
Original-Signed-off-by: Arindam Roy <arindam.roy@intel.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/316009
Original-Commit-Ready: Arindam Roy <rarindam@gmail.com>
Original-Tested-by: Arindam Roy <rarindam@gmail.com>
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/12952
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Currently, the Power Limit 1 (PL1) value is 6W which is
low for high performance KPIs. This patch updates PL1
value as TDP. SKL-U has 15W TDP.
BRANCH=none
BUG=none
TEST=Build and booted on lars.
Change-Id: Ic1313385e0aa1760b473a34c853a95c76257eecf
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: a47faee53e08da81602b485937621fd49eb2ddbf
Original-Change-Id: I7c91dcdc82525a6d2b706f8f504ba48601097ef7
Original-Signed-off-by: David Wu <David_Wu@quantatw.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/316370
Original-Commit-Ready: David Wu <david_wu@quantatw.com>
Original-Tested-by: David Wu <david_wu@quantatw.com>
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Original-Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/12953
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
modify the P/N in samsung K4E6E304EE-EGCF SPD from K4E6E304ED-EGCE to
K4E6E304EE-EGCF
BRANCH=none
BUG=chrome-os-partner:48299
TEST=build chell and use gooftool to probe and P/N match
Change-Id: Ie560e5c0d4b9a3cfb34c3856911930fb8159764e
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: dabe5eaa8abf54f4e4a5492062adca6ef9b4634d
Original-Change-Id: Ie8d44ac6032e5213928bfae2a2ac5877d4193d62
Original-Signed-off-by: Wisley <wisley.chen@quantatw.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/316100
Original-Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/12951
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Adding support for Maxim 98357A audio amplifier.
BUG=chrome-os-partner:44481
BRANCH=None
TEST=Build & boot on Skylake kunimitsu Fab4 with MAXIM codec.
Verify audio playback works using MAXIM.
Change-Id: I4f020ccae540b02d5d533704a52cebb7805715fe
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: c0a81300e02e917500fa3c0241c95dd795abaf04
Original-Change-Id: I8875c9a55f09b1ec353203cfcb2186dc5fd66542
Original-Signed-off-by: Rohit Ainapure <rohit.m.ainapure@intel.com>
Original-Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/309894
Original-Tested-by: Rohit M Ainapure <rohit.m.ainapure@intel.com>
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/12949
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Provide an option for including the NHLT blobs within the
glados mainboard directory while also adding the ACPI NHLT
table generation that the current hardware supports.
BUG=chrome-os-partner:44481
BRANCH=None
TEST=Built and booted. Headphones, speakers, and mic on camera
emits and creates sound albeit not the greatest.
Change-Id: Iaf910041453695b7125b254ca5d71e8ccbd0b02f
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: ea77d326ba1c33b100c34066ed361a55dfa14ce3
Original-Change-Id: I5d93c3a7fa4cf68ba91f1398b4bd04504a28fef2
Original-Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/315520
Original-Tested-by: Duncan Laurie <dlaurie@chromium.org>
Original-Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/12948
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Provide an option for including the NHLT blobs within the
glados mainboard directory while also adding the ACPI NHLT
table generation that the current hardware supports.
BUG=chrome-os-partner:44481
BRANCH=None
TEST=Built and booted. Headphones, speakers, and mic on camera
emits and creates sound albeit not the greatest.
Change-Id: I6e36c0a99a73cdcb2bf6ccfbfc886a594f989a39
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 5b0383a93f054011dd7c18519ece4e6f1944366d
Original-Change-Id: I6f8bd15c72fa89756382af99bddb6cb6abe89905
Original-Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/313794
Original-Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/12939
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
The use of a NHLT table is required to make audio work
on the skylake SoCs employing the internal DSP. The table
describes the audo endpoints (render vs capture) along with
their supported formats. These formats are not only dependent
on the audio peripheral but also hardware interfaces. As such
each format has an associated blob of DSP settings to make
the peripheral work. Lastly, each of these settings are provided
by Intel and need to be generated for each device's hardware
connection plus mode/format it supports. This patch does not
include the dsp setting blobs.
The current supported connections:
- digital mic array 2 channel
- digital mic array 4 channel
- Maxim 98357 amplifier
- ADI ssm4567
- NAU88L25 headset codec
BUG=chrome-os-partner:44481
BRANCH=None
TEST=Built glados. Speakers, headphones, and mic on camera decently
worked.
CQ-DEPEND=CL:*239598
Change-Id: If1a9be97573b9b160893944661790cac7df26fca
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 1f5514e27811c500732de97e1cc7edeced2607e7
Original-Change-Id: Ib42e895f00e7605cb30ce24d9b8dd00bf68a7477
Original-Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/313998
Original-Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/12938
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Intel's SST (Smart Sound Technology) employs audio support
which may not consist of HDA. In order to define the topology
of the audio devices (mics, amps, codecs) connected to the
platform a NHLT specification was created to pass this
information from the firmware to the OS/userland.
BUG=chrome-os-partner:44481
BRANCH=None
TEST=Tested on glados. Audio does get emitted and some mic recording
works.
Change-Id: I8a9c2f4f76a0d129be44070f09d938c28a73fd27
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 2472af5793dcffd2607a7b95521ddd25b4be0e8c
Original-Change-Id: If469f99ed1a958364101078263afb27761236421
Original-Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/312264
Original-Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/12935
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Currently, the Power Limit 1 (PL1) value is 6W which is
low for high performance KPIs. This patch updates PL1
value as TDP. SKL-U has 15W TDP.
BRANCH=None
BUG=None
TEST=Built and boot on kunimitsu. Check for the PL1 value over
sysfs interface
"/sys/class/powercap/intel-rapl:0/constraint_0_power_limit_uw".
Load the system with Aquarium 1000 Fish, average FPS should be
meeting target 60 with this change.
Change-Id: I8e083192e8018edc2cf8b88530df1e05ede10bde
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: eb9aa00a4271875b5471c33883aa7da022f1cb0e
Original-Change-Id: I0c61fe1a9f76a9cf9a306240fb66d4c081d2bb5e
Original-Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/314416
Original-Commit-Ready: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Original-Tested-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Original-Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Original-Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/12934
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
BUG=chrome-os-partner:48017
BRANCH=none
TEST=Verify eMMC is working fine.
Change-Id: If02d969029a9eb8d05148ee958fd34225c8a88fe
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: dca385c2bbf11c9eb79fd0761b2b335f8fdff491
Original-Change-Id: I371036426f17530409b46af285b18f4522739ee7
Original-Signed-off-by: David Wu <David_Wu@quantatw.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/313912
Original-Commit-Ready: David Wu <david_wu@quantatw.com>
Original-Tested-by: David Wu <david_wu@quantatw.com>
Original-Reviewed-by: David Wu <david_wu@quantatw.com>
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Original-Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/12618
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
These were mostly written as part of the coreboot project, so get
the standard coreboot license header.
memmove.c came from the linux kernel, so also gets the standard
coreboot v2 license header, but gets the added attribution that it
was derived from the linux kernel. Unlike many coreboot files,
this file may not be re-licensed as GPL V3.
Change-Id: I1fdc26b543e059f7a42d4b886f7222f4c74b959d
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/12916
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Original-Reviewed-on: https://chromium-review.googlesource.com/309122
Original-Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Original-Tested-by: Hannah Williams <hannah.williams@intel.com>
Change-Id: Ia24dbeb6b23ccbbb380843a4684def578cde168a
Signed-off-by: Divya Sasidharan <divya.s.sasidharan@intel.com>
Reviewed-on: https://review.coreboot.org/12727
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
thermal.asl was written as part of the coreboot project, so gets
the standard coreboot license header.
ec_commands.h came from the chrome ec tree, so gets the BSD license
from that tree as mentioned in the header that has been replaced.
Change-Id: I514138fd4ed236105998b25d1d2d8eb8441cf91d
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/12918
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
These were mostly written as part of the coreboot project, so get
the standard coreboot license header.
Change-Id: Ief13339647d3172e65bb18e6dcb54312a5c9472e
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/12917
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
These were all written as part of the coreboot project, so get
the standard coreboot license header.
Change-Id: I51e1e504b3bc7be2a00c9356d8775b87f2a1db5a
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/12912
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Incorrect bus-core-ratio been used to generate P-state table
Original-Reviewed-on: https://chromium-review.googlesource.com/290681
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Change-Id: I4a34ec80ff3f2ed46dc074c9f8fe06756db8b357
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/12731
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
The read and write routines take a number of bytes to write, which
should be 1,2, or 4. We now return an error if an invalid size
is specified.
Change-Id: I93344bc0837c3715fc7660503f405c8878eb711c
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/12936
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Values are taken from the vendor BIOS of my X200s. Notable effect:
Stops display from flashing during native graphics init / Linux mode
setting.
Change-Id: Ie5d9efc010a78dd46317b6bbdb7bfacc2c9d2cbf
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/12886
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Register settings are the same as on newer chips (compare sandy-
bridge), just at different locations.
Change-Id: Iea0359165074298a376e0e2ca8f37f71b83ac335
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/12885
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Skip everything but the final setting of PP_CONTROL, i.e. triggering
the power up. The settings with PANEL_UNLOCK_REGS are useless as no
lockable registers were touched in between. Also the loop waiting for
the panel power up to finish was a no-op as the registers with the
power timings were never filled (see follow-up commits).
Change-Id: Ife27dcafdf197b2246c4e69f2bf7a3a6765d1d82
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/12884
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
The century byte is used by most RTC (default 0x32@nvram).
Even the century byte can disabled via ACPI it's more safe to reserve
it's space. Because some RTC will act with that byte anyhow.
Some OS overwrite it when syncronize the RTC.
Change-Id: I078c0c57215ccb925afa85b9d067f15268801ec9
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Reviewed-on: https://review.coreboot.org/11853
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
These were all written as part of the coreboot project, so get
the standard coreboot license header.
Change-Id: I4fccc8055755816be64e9e1a185f1e6fcb2b89ae
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/12911
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
These were all written as part of the coreboot project, so get
the standard coreboot license header.
Change-Id: I74438e8032c84f4190ef49f306969f7157234001
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/12910
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
This continues what was done in commit a73b93157f2
(tree: drop last paragraph of GPL copyright header)
Change-Id: Ifb8d2d13f7787657445817bdde8dc15df375e173
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/12914
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Because these platforms haven't been getting build testing, they've
missed out on some of the improvements that the other platforms have
gotten.
Enable MAINBOARD_HAS_LPC_TPM so that they will build.
Change-Id: I5e44135b6dfa800fa14e5b08c3e3e5921d50b082
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/12865
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Remove redundant call to dram_mrscommands().
Change-Id: I157915b4432093c556b538433e3337db1e9c525f
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/12891
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Change-Id: Ifa7dd593f70921a99d937104960e26100de28089
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/12421
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
