| Age | Commit message (Collapse) | Author |
|---|
|
Remove the existing FSP 4221.00 headers subdirectory called
4221.00_google, and have Google vendor devices use FSP 4301.01.
BUG=b:306181828
TEST=`emerge-brya coreboot chromeos-bootimage`, flash and boot skolas to kernel.
Change-Id: Ic64b3aec62f0d6302278393bf06d090f43c0d592
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78444
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: <srinivas.kulkarni@intel.com>
Reviewed-by: Bora Guvendik <bora.guvendik@intel.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Package C-state auto demotion feature allows hardware to determine lower
C-state as per platform policy. Since platform sets performance policy
to balanced from hardware, auto demotion can be disabled without
performance impact.
Also, disabling this feature results soc to enter below PC8 state and
additional power savings ~30mW in Local-Video-Playback scenario.
Change-Id: I6ff408280178a24686180f72f79522d2741607a1
Signed-off-by: Sukumar Ghorai <sukumar.ghorai@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78278
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
System sleep time (SLP_S0 signal asserted) is measured in ticks, for
Meteor Lake soc in 122us (i.e. ~8197Hz) granularity/ticks.
Change-Id: I1e95cd69e941d4d72d5c36a07660ca07ee2499ba
Signed-off-by: Sukumar Ghorai <sukumar.ghorai@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78277
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Intel platforms use Low Power Idle Table (LPIT) to enumerate platform
Low Power Idle states. There are two types of low power residencies
a) CPU PKG C10 - read via MSR (Function fixed hardware interface)
b) Platform Controller Hub (PCH) SLP_S0 - read via memory mapped
Ref. https://www.uefi.org/sites/default/files/resources/Intel_ACPI_Low_Power_S0_Idle.pdf
System sleep time (SLP_S0 signal asserted) is measured in ticks,
varies in every platform and based on PMC clock.
BUG=b:300440936
TEST=check kernel cpuidle sysfs for non-zero residency after s0ix cycle
and both must match
cat /sys/devices/system/cpu/cpuidle/low_power_idle_system_residency_us
cat /sys/kernel/debug/pmc_core/slp_s0_residency_usec
Change-Id: I401dd4a09a67d81a9ea3a56cd22f1a681e2a9349
Signed-off-by: Sukumar Ghorai <sukumar.ghorai@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78164
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch ensures that the IGD joins the MBUS when the firmware splash
screen feature is enabled (aka BMP_LOGO config is enabled).
For ChromeOS platform, it prevents the i915 driver from reinitializing
the display, which can save up to 75ms-80ms of boot time and eliminate
a brief period of blank screen between the firmware splash screen and
the OS login prompt.
BUG=b:284799726
TEST=Able to build and boot google/rex.
Change-Id: I36af167afa902053a987602d494a8830ad9b1b1a
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78387
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
This patch implements `.final` hooks for the IGD device to perform the
required operations before handing the control to the payload or OS.
The MBUS (Memory Bus) is a high-speed interface that connects the
graphics controller to the system memory. It provides a dedicated data
path for graphics data, which helps to improve graphics performance.
The MBUS is a key technology that helps to make the Intel i915 driver
powerful and versatile graphics drivers available. It provides the
high-speed data transfer capabilities that are essential for smooth
and responsive graphics performance.
Enable this config to ensure that the Intel GFX controller joins the
MBUS before the i915 driver is loaded. This is necessary to prevent
the i915 driver from re-initializing the display if the firmware has
already initialized it. Without this config, the i915 driver will
initialize the display to bring up the login screen although the
firmware has initialized the display using the GFX MMIO registers and
framebuffer.
Kernel graphics driver can avoid redundant display init by firmware,
which can optimize boot time by ~15ms-30ms.
Ensures hashing mode is 1x4 to enable a single pipe between Pipe A or B.
Typically, internal display is on Pipe-A, so 1x4 restricts MBUS joining
to internal display alone.
BUG=b:284799726
TEST=Able to build and boot google/rex
Change-Id: I60ae76dc783383e027e66edbcdeeb535472caeb1
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78385
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Eric Lai <ericllai@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enabling support of WiFi SAR table for all rex variants by
setting the option at baseboard level.
BUG=b:290689824
TEST=emerge-rex coreboot
Change-Id: I17709cb5d75b56c6c1f386ab527c5c8730011bed
Signed-off-by: YH Lin <yueherngl@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78308
Reviewed-by: Eric Lai <ericllai@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
|
|
Sync'ing Karis' FW_CONFIG definitions stored in CBI,
```
_FW_MASKS = struct(
DB_USB = 0x00000003, # bit1~bit0
STYLUS = 0x00000004, # bit2
AMP = 0x00000038, # bit5~bit3
FAN = 0x000000C0, # bit7~bit6
MIPI_CAM = 0x00000300, # bit9 ~ bit8
FP_MCU = 0x00000C00, # bit11 ~ bit10
KB_TYPE = 0x00001000, # bit12
WIFI_TYPE = 0x00002000, # bit13
)
_FW_CONFIGS = struct(
DB_USB_UNKNOWN = hw_topo.make_fw_config(_FW_MASKS.DB_USB, 0),
DB_USB4_ANX7452 = hw_topo.make_fw_config(_FW_MASKS.DB_USB, 1),
STYLUS_ABSENT = hw_topo.make_fw_config(_FW_MASKS.STYLUS, 0),
STYLUS_PRESENT = hw_topo.make_fw_config(_FW_MASKS.STYLUS, 1),
AUDIO_ALC5650 = hw_topo.make_fw_config(_FW_MASKS.AMP, 0),
FP_MCU_ABSENT = hw_topo.make_fw_config(_FW_MASKS.FP_MCU, 0),
FP_MCU_NUVOTON = hw_topo.make_fw_config(_FW_MASKS.FP_MCU, 1),
FP_MCU_ELAN = hw_topo.make_fw_config(_FW_MASKS.FP_MCU, 2),
WIFI_TYPE_CNVI = hw_topo.make_fw_config(_FW_MASKS.WIFI_TYPE, 0),
WIFI_TYPE_PCIE = hw_topo.make_fw_config(_FW_MASKS.WIFI_TYPE, 1),
MIPI_UF_CAM_HI556 = hw_topo.make_fw_config(_FW_MASKS.MIPI_CAM, 0),
)
```
BUG=b:290689824
TEST=emerge-rex coreboot
Change-Id: I1e4965c009edc595f24c04ac82d81aa0e723bbf3
Signed-off-by: YH Lin <yueherngl@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78261
Reviewed-by: Eric Lai <ericllai@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
WiFi SAR table for karis will be place into the CBFS later on and
as a result adding the hook in coreboot to make use of the SAR
table once the table is available.
BUG=b:290689824
TEST=emerge-rex coreboot
Change-Id: Ic989024ab9eb0fc439fc701c335a85986c4cfec5
Signed-off-by: YH Lin <yueherngl@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78260
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Update default fan settings(FAN_SETTING_1) in FAN field.
Bit 6-7, FAN, 0 --> FAN_SETTING_1
BUG=b:290689824, b:294155897
TEST=Dump ssdt table and check fan settings is existed
Change-Id: Id69ec67202b5d769cd3a9a68344a6d8913ebd78b
Signed-off-by: Tyler Wang <tyler.wang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78216
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
Commit 9b230ae2955 introduced a redefinition of the config option
`BOARD_GOOGLE_BROX`, which is already defined in Kconfig.name
accordingly and thus causing a Kconfig warning. Fix that by removing the
type redefinition.
Change-Id: Iea6219a686a23d8d48a0bfb6ac642efd482fded9
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78394
Reviewed-by: Martin L Roth <gaumless@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Configure GPIOs according to schematics revision 20231013.
BUG=b:299284564, b:298328847, b:299570339
TEST=emerge-brya coreboot
Change-Id: I1ccab46b9f622fb98920d316c31800f39dc8ff95
Signed-off-by: Morris Hsu <morris-hsu@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78384
Reviewed-by: David Wu <david_wu@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Bob Moragues <moragues@google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
Create the anraggar variant of the nissa reference board by copying
the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.5.0).
BUG=b:304920262
BRANCH=None
TEST=util/abuild/abuild -p none -t google/brya -x -a
make sure the build includes GOOGLE_ANRAGGAR
Change-Id: I95e72188679fc825c94c4043ed02b0aad310c6a3
Signed-off-by: wuweimin <wuweimin@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78363
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
For Raptor Lake, select Raptor Lake's .fd file and header.
TEST=Boot to OS on Google Brya board with RPL silicon.
Signed-off-by: Bora Guvendik <bora.guvendik@intel.com>
Change-Id: Ib3172b06b23e19be453142af764dd027bfe8043d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78014
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
Disable SD card GPIO with fw_config for quandiso units without SD
card and pull GPP_H12 to high to match the spec.
BUG=b:296506936
BRANCH=firmware-nissa-15217.B
TEST=emerge-nissa coreboot
Change-Id: Iad6789d42b9a3f9b979fd481a88cc7d69db2dcfe
Signed-off-by: Robert Chen <robert.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78253
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Shawn Ku <shawnku@google.com>
|
|
This patch adds support for detecting dual displays (eDP and HDMI) on
Intel platforms. This information is useful for setting the
`lb_framebuffer.has_external_display` variable, which is used to
determine whether depthchage should avoid shutting down when an
extended display is present.
TEST= Able to build and boot google/rex, where depthchage now
successfully avoids shutting down when both eDP and HDMI displays
are attached.
w/o this patch:
with eDP and HDMI attached: .has_external_display=0
with eDP attached: .has_external_display=0
with HDMI attached: .has_external_display=1
w/ this patch:
with eDP and HDMI attached: .has_external_display = 1
with eDP attached: .has_external_display=0
with HDMI attached: .has_external_display=1
Change-Id: Ie39d48da75a21e3508a1fbcf09da31caedaa1c0a
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78383
Reviewed-by: Eric Lai <ericllai@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Iec6e05bbe9fad7d78002560b78169dc293294af6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78341
Reviewed-by: Eric Lai <ericllai@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
|
|
This code only gets built when the SOC selects
SOC_AMD_COMMON_BLOCK_DATA_FABRIC_EXTENDED_MMIO which no SoC before Genoa
does.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ia5495ebf0f157fd0c456ce44acaf1ab222a188dd
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78340
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
|
|
Due to copy-paste error, the UART2 device name is the same as
UART1. Fix it.
Change-Id: I796d09f321101a36731a56099af738c9485df8a2
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78350
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Krystian Hebel <krystian.hebel@3mdeb.com>
|
|
Reserve SBREG BAR if it is outside of the PCH reserved memory range.
Desktop series processors have larger SBREG BARs, which, unlike mobile
processors, do not fall into the standard PCH reserved range
(0xfc800000 - 0xfe7fffff). Create a separate reservation for such a case. There is no telling what could happen if the reservation is not
made in ACPI.
TEST=Boot Windows 11 and Ubuntu 22.04 on MSI PRO Z690-A DDR4
Change-Id: Ibaf45daba37e3acfcea0e653df69fa5c2f480c4a
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77445
Reviewed-by: Krystian Hebel <krystian.hebel@3mdeb.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
|
|
BUG=b:301150499
TEST=Compiled and tested on google/redrix - PERST# goes low when wwan
modem goes into runtime suspend.
Change-Id: Ib09d5a6091cedfce24da49390cf980414f97a2c9
Signed-off-by: Paweł Anikiel <panikiel@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78349
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <inforichland@gmail.com>
|
|
When battery level is below critical level or battery is not present,
cpus need to run with a power optimized configuration to avoid platform
instabilities. This will check the current battery status and configure
cpu power limits properly.
BUG=b:296952944
TEST=Build rex0 and check cpu power limits are configured with
a performance efficient configuration and the platform boots to OS if
battery level is above the critical level. And check cpu power limits
are configured with a power optimized configuration and boots to OS
without an issue if battery is not present or battery level is at or
below critical level.
Change-Id: I12fd40abda76c8e7522b06a5aee72665f32ddec8
Signed-off-by: Jamie Ryu <jamie.m.ryu@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78322
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This adds is_battery_present_and_above_critical_threshold to check the
battery is present and the battery level is above critical level.
BUG=b:296952944
TEST=Build rex and check is_battery_present_and_above_critical_threshold
returns the correct battery status.
Change-Id: Ib38be55bc42559bab4f12d5e8580ddc3e1a6acc1
Signed-off-by: Jamie Ryu <jamie.m.ryu@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78321
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
This CL is just getting the initial brox framework to get the
baseboard building. Copied files from brask baseboard and tried to
remove contents of some files like the device tree and memory IDs.
Added support for memory part "MT62F512M32D2DR-031 WT:B", mapped to
DRAM ID 0.
BUG=b:300690448
BRANCH=None
TEST=./util/abuild/abuild -p none -t GOOGLE_BROX -x -a
Change-Id: I929b465646ac4c69d4bab33ce23848c7b1fa0f98
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78009
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
SATA controller isn't used & hence disable.
Change-Id: Iab2d597e6a0f22b946e657a2851b68f752d1f7d4
Signed-off-by: Naresh Solanki <naresh.solanki@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77893
Reviewed-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The board has three SATA controllers, so add the remaining two
on PCI device 18.0 and 19.0.
TEST=Verify in lspci the sata controllers.
Change-Id: Ia654c4ef895b52338554d89c25f61b262fbbcbbb
Signed-off-by: Naresh Solanki <naresh.solanki@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77892
Reviewed-by: Annie Chen <chen.annieet@inventec.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Patrick Rudolph <patrick.rudolph@9elements.com>
|
|
BUG=NONE
TEST=Tested on Rex, touch over SPI works properly.
Signed-off-by: Eran Mitrani <mitrani@google.com>
Change-Id: If339f7a010fa51bf73b8898a55643b5e921d93b1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78318
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
Systemagent related functions are not used in this file. Remove the
unused the header file.
Change-Id: Ifbb04898e9dcebef96d8c73771e66e0d6fabc7fb
Signed-off-by: Krishna Prasad Bhat <krishna.p.bhat.d@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78312
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Ronak Kanabar <ronak.kanabar@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Update overridetree base on schematics revision 20230923.
BUG=b:299284564, b:298328847, b:299570339
TEST=emerge-brya coreboot
Change-Id: I0aff94ef3233fbc4f52d33bb2dc1285b4fe473f9
Signed-off-by: Morris Hsu <morris-hsu@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78212
Reviewed-by: David Wu <david_wu@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
To support an RPL SKU on dochi, it must use the FSP for RPL.
Select SOC_INTEL_RAPTORLAKE for dochi so that it will use the RPL
FSP headers.
BUG=b:299570339
TEST=emerge-brya intel-rplfsp coreboot
coreboot-private-files-baseboard-brya
Change-Id: I51c28744bd9f21fae58bad38abb01d38965140a4
Signed-off-by: Morris Hsu <morris-hsu@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78323
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: David Wu <david_wu@quanta.corp-partner.google.com>
|
|
Pull GPP_C1 to high in ramstage to meet touchscreen power sequence.
BUG=b:302236370
BRANCH=firmware-nissa-15217.B
TEST=emerge-nissa coreboot chromeos-bootimage
& test touchscreen function on quandiso DUT
Change-Id: Ia9f600ec0cc4be2d77ff08c0ae8951c90aec944f
Signed-off-by: Robert Chen <robert.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78264
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shawn Ku <shawnku@google.com>
Reviewed-by: Derek Huang <derekhuang@google.com>
|
|
This updates NVM Configuration according to EEPROM BRCA016GWZ-W
datasheet for rex World Facing Camera module - O9B13-NT01BA to
enumerate Camera module properly.
BUG=b:301226048
TEST=Build rex0 and check SSDT table is updated correctly. Check
"cros-camera-tool modules list" lists up the modules properly.
cros-camera-tool modules list:
/sys/devices/pci0000:00/0000:00:15.0/i2c_designware.0/i2c-0/i2c-PRP0001:01/i2c-PRP0001:011/nvmem
/sys/devices/pci0000:00/0000:00:19.1/i2c_designware.4/i2c-13/i2c-PRP0001:03/i2c-PRP0001:032/nvmem
[ {
"module_id": "KC6977",
"sensor_id": "OV013b",
"sysfs_name": "i2c-0/i2c-PRP0001:01"
}, {
"module_id": "CH3c6d",
"sensor_id": "HN0556",
"sysfs_name": "i2c-13/i2c-PRP0001:03"
} ]
Change-Id: I51bdf249549d3e03180e9d126a85e9dff91028db
Signed-off-by: Jamie Ryu <jamie.m.ryu@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78211
Reviewed-by: Kiran2 Kumar <kiran2.kumar@intel.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
This reverts commit 5c35d30ffc7382af46b62044a5cf5326b1e57708.
Reason for revert: Here we need to confirm whether the issue in
mtl-staging-MTL.3323.92 has been improved in the QS sample
in the factory build.
BUG=b:287170545
TEST=Able to idle for more than 5+ hours without any hang.
Change-Id: I4517bbbefe11d95623d7e16a5e4bba2dd6f408e1
Signed-off-by: Wentao Qin <qinwentao@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78320
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Mike Lee <mike5@huaqin.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
|
|
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Iaf4a1fd61ad1d545b1ea0ab3fcf6c7a3d0260cd0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78319
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Varshit Pandya <pandyavarshit@gmail.com>
|
|
Confirmed with vendor, Elan touchscreen HID should set to "ELAN9004".
Correct Elan touchscreen HID to "ELAN9004" for karis.
BUG=b:294155897
TEST=Dump the SSDT on karis and check the HID had been modified.
Change-Id: I6ebb02540c894460388b9b9fe03f5c4031f8186d
Signed-off-by: Tyler Wang <tyler.wang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78266
Reviewed-by: Eric Lai <ericllai@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
The write to register 0x42 has no effect as at this point all
of the bits are read-only. Drop the line.
Change-Id: I7293e6eaa2d0bac5efe8316029bdecb04a5586e9
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78238
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Because integrated PCI devices are hidden in chip_ops
the PCI enumeration code never sees them.
When hiding static devices mark them as hidden so the
PCI enumeration no longer complains about them being
missing, even though they are present and were working
just fine.
Test: Disabled southbridge devices no longer appear in
"Leftover static devices:" log.
Change-Id: Iae70072a85b62a456102190a5f72f4d652ad6d5a
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78230
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Warn when a device took longer than usual to appear.
Use the PDS bit to detect if a root port has a downstream
device connected and warn if enumeration failed.
Test: On Lenovo X220 all PCIe device are visible, thus the
added code path is never taken.
Change-Id: I86b498b89d672b239d9951e116dc3680030666a6
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78229
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Use defines instead of magic values.
Test: Lenovo X220 still boots and all PCIe devices are
still working.
Change-Id: Ie8fc7cc863017da07dd3ed37b487dae18de92b18
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78293
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
- Use pci_find_capability() and defines from pci_def.h
- Set the 'Hotplug Capable' bit and 'Hot Plug Surprise' bit in SLCAP
for hotplugable PCIe slots.
- Assign unique slot number and set power limit for PCIe root ports
that have a slot connected. For integrated devices clear slot number
and power limit.
Test: System still boots and all PCIe devices are working.
Change-Id: I03aeb0a1ff0041901acc20fe700d3f7995d22366
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78228
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
This reverts commit ee4191852abf9b24f822468250c24edb993497c6.
Reason for revert: In schematic a sdcard write protection pull-down
resistor was added, so need to disable GL9750 invert WP function
Change-Id: I00a8f43094d8b3674a4bbaeed24b96aab64b9b75
Signed-off-by: Kun Liu <liukun11@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78295
Reviewed-by: Rui Zhou <zhourui@huaqin.corp-partner.google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Eric Lai <ericllai@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
|
|
This functionality will eventually be used by the common data fabric
domain resource reporting code.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ieedd432c144e53e43d8099ec617a15056bb36fd1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78307
Reviewed-by: Eric Lai <ericllai@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I18871af0a8dbc1423524b681d516476e63b9596a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78306
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Change-Id: Iefe61d25367bbe5cff0cacbfbafa32607de77d0f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76509
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Change-Id: I79ebbcc6a4a3a93e8437ef56aebdcf72f9a3e6ab
Signed-off-by: Varshit Pandya <pandyavarshit@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78267
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Signed-off-by: Varshit Pandya <pandyavarshit@gmail.com>
Change-Id: I1529657f30b6e228c2e3cd7e0438255522381367
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76507
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I2e827e9ffbb2ec1be0f1247b77660a9fdeb04f7b
Signed-off-by: Varshit Pandya <pandyavarshit@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78222
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Add SMI definitions as per Genoa PPR Doc #55901
Change-Id: I491f4075cef8976e4b0762752c9e2e3c2ef886d5
Signed-off-by: Varshit Pandya <pandyavarshit@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78221
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Add GPIO definitions as per Genoa PPR Doc #55901
Change-Id: I0c4e425699c9a158ca95a1baf94f7756f0b12b44
Signed-off-by: Varshit Pandya <pandyavarshit@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78220
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
The tochscreen isn't powered on yet when the detection is done, it
makes touchscren no function.
Set touchscreen power and reset GPIOs correctly in romstage and
ramstage to make the detect feature works.
BUG=b:303130400
TEST=(1) emerge-rex coreboot
(2) Test on karis, touchscreen function works
Change-Id: I6c7815b81eb47fb41e58233fde512ac6b9c000a7
Signed-off-by: Tyler Wang <tyler.wang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78254
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Eric Lai <ericllai@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
On ICH9 the SPI control register is not naturally aligned
and a word write might be split into smaller naturally aligned
I/O transactions.
As the first byte starts a new SPI transfer, replace the existing
word write with two byte writes and write the second byte first.
This is required for platforms that do not support unaligned
word I/O instructions and would start a SPI transfer while the
second byte hasn't reached the control register yet.
TEST: Virtual SPI controller on qemu 8.0 doesn't start a transfer
early.
Change-Id: Id05b1a080911b71b94ef781c6e26d98165f02f67
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78090
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
We have a tiny HEAP_SIZE by default, except when we don't, and
mainboards that override it, or not.
Since memory isn't exactly at a premium these days, and unused heap
doesn't cost anything extra, just crank it up to the highest value
we have in the tree by default and remove all overrides.
Change-Id: I918a6c58c02496e8074e5fba06e38d9cfd691020
Signed-off-by: Patrick Georgi <patrick@coreboot.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78270
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This is in preparation of a larger heap. I went for 2MB because why not?
Change-Id: I51f999a10ba894a7f2f5fce224d30bf914107c38
Signed-off-by: Patrick Georgi <patrick@coreboot.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78273
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Yidi Lin <yidilin@google.com>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Change-Id: I4965eac4ec3d600b1e840affce4e5b4fa2ea4360
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76508
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
|
|
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Signed-off-by: Martin Roth <gaumless@gmail.com>
Change-Id: Ic9553e6016c92c9b1678c395cd6a9e6860bf8a76
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76506
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Signed-off-by: Varshit Pandya <pandyavarshit@gmail.com>
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Change-Id: I05990c2aca40d9cf47a9ebdfd269b80b8f60e300
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76505
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Configure GPIOs according to schematics revision 20230923.
TEST=emerge-brya coreboot
Change-Id: I10bd1b72c9b0299b8d29ab642fddb5f0c4727652
Signed-off-by: Morris Hsu <morris-hsu@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78112
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: David Wu <david_wu@quanta.corp-partner.google.com>
Reviewed-by: Ren Kuo <ren.kuo@quanta.corp-partner.google.com>
|
|
Some Type-C monitors do not immediately assert HPD. If we enter FSP-S
before HDP is asserted, display initialisation may fail. So wait for
HPD.
This is similar to commit b40c6009141e ("mainboard/hatch: Fix puff DP
output on cold boots") on puff, except we don't use
google_chromeec_wait_for_displayport() since that EC command was removed
for TCPMv2 (https://crrev.com/c/4221975). Instead we use the HPD signals
only. By waiting for any HPD signal (Type-C or HDMI), we skip waiting if
HDMI is connected, which is the same behaviour as puff and fizz.
TEST=On dibbi, connect a display via a Type-C to HDMI dongle and check
the dev and recovery screens are now displayed correctly. Also check the
logs in the following cases:
Cold reboot in dev mode, Type-C to HDMI dongle:
HPD ready after 800 ms
Warm reboot in dev mode, Type-C to HDMI dongle:
HPD ready after 0 ms
Cold/warm reboot in dev mode, direct Type-C:
HPD ready after 0 ms
Cold/warm reboot in dev mode, direct HDMI:
HPD ready after 0 ms
Cold/warm reboot in dev mode, no display:
HPD not ready after 3000 ms. Abort.
Change-Id: Id4657b5d5a95a68ecbd9efcf3585cf96ad1e13e1
Signed-off-by: Reka Norman <rekanorman@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78294
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sam McNally <sammc@google.com>
|
|
update DTT settings for thermal control, as follows:
1.Cancel TCPU trip point and fine tune other protection temperature on the Critical policy table
2.Fine tune EC/Bios protection temperature
BUG=b:291217859
TEST=emerge-rex coreboot
Change-Id: I0e2ff6eea9fed71ad7680c1fac4921984b87aca5
Signed-off-by: Kun Liu <liukun11@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78290
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: zhongtian wu <wuzhongtian@huaqin.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Internal testing showed that CPU heatsink gets hot and temperature
goes over 75C. In this situation, the fan does not even start
to lower down CPU temperature. This is because of existing temperature
thresholds of TSR0 and TSR1 sensors are set at 45C to start fan.
With updated new settings based on tuning from thermal team,
the fan starts early at 43C for TSR0 and TSR1 so the CPU temperature
stays below 75C.
BUG=b:302673874
TEST=Built and tested on google/rex board
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Change-Id: I6580652d6165946e98ecf1b46ace3352cd34dcdf
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78279
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
It's needed for future work.
Change-Id: I3419d11072bc0e3791ad08144c2a25c607550f28
Signed-off-by: Patrick Georgi <patrick@coreboot.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78269
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Introduce pci_is_hotplugable is helper to find hotpluggable
PCIe devices.
Test: PCI express slot is still marked as the only hotpluggable
PCIe root port.
Change-Id: I25aae540ff2ffa3ec5b93ed9caa838b4e50048d2
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78227
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Jan Samek <jan.samek@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Follow the PCH BIOS spec more closely by porting the broadwell
and braswell PCIe downstream device detection. To safe power
disable PCIe root ports that have no downstream device connected.
By setting the FLAGS_SLOT bit in register PCI_EXP_FLAGS the
PCI_EXP_SLTSTA_PDS bit will be updated with in band device
detection from the PCIe PHY. While this is primarly used for PCIe
hot-plug detection, it is more reliable than probing for downstream
devices by reading DID/VID PCI registers.
The FLAGS_SLOT bit should stay cleared for integrated devices,
as those are known to be present, but to simplify the code all
PCIe ports will have the FLAGS_SLOT bit set. There currently
used devicetrees might also be lacking integrated devices on
the PCH root ports...
The SLOTCAP field must be updated by BIOS when the FLAGS_SLOT
is set, but it shouldn't be filled for integrated devices. Until
now the SLOTCAP field has always been populated and it never
was a problem.
- Set FLAGS_SLOT "Slot Implemented" bit early.
- Read bit PCI_EXP_SLTSTA_PDS to detect connected downstream
devices as done on braswell.
- Disable unused PCIe slots that are not hotplugable.
- Set BIT26 in register 0x338 and wait for bits in register 0x328
to clear as done on broadwell.
Test: Tested on Lenovo X220. Unused root ports are disabled and port
that are in used or marked hot-plug are kept enabled.
Change-Id: I8ccfcab2e0e4faba8322755a4f8c2108d9b007ac
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78226
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Dojo fails to boot from NVMe with CONFIG_RESOURCE_ALLOCATION_TOP_DOWN
enabled. The root cause is using __fls() will get a smaller value when
the size is not a power of 2, for example, __fls(0x3000000) = 25. Hence
the PCIe translation window size is set to 0x2000000. Accessing
addresses higher than 0x2300000 will fail.
Fix translation window by splitting the MMIO space to multiple tables if
its size is not a power of 2.
Resolves: https://ticket.coreboot.org/issues/508.
TEST=Build pass and boot up to kernel successfully via SSD on Dojo
board, it can boot with and without the
CONFIG_RESOURCE_ALLOCATION_TOP_DOWN option.
BUS=b:298255933
BRANCH=cherry
Change-Id: I42b0f0bf9222d284dee0c29f1a6ed6366d6e6689
Signed-off-by: Jianjun Wang <jianjun.wang@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78044
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
PCH BIOS spec says that BIOS must clear BIT26 in register 0x338
in PEI, as done on lynxpoint.
Copy and adapt the lynxpoint code to do the same on bd82x6x.
Add special case for UM77 chipset, which only has 4 PCIe ports.
Test: System still boots and all PCIe ports are fully working.
Change-Id: I865818c0c22194fffcb2bbdf8c43737b0dce2307
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78225
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Commit 26d54b70e282 ("soc/amd/common/cpu: use TSC_MONOTONIC_TIMER for
SOC_AMD_COMMON_BLOCK_TSC") updated all the AMD SoCs with Zen-based CPU
cores to use TSC_MONOTONIC_TIMER. The same change adjusted the PSP
Verstage timestamps (in microseconds) to the x86 TSC rate. But it
included only the base_time during the adjustment leaving the individual
entry timestamp. This leads to incorrectly adjusted PSP Verstage
timestamps. Fix the adjustment logic.
BUG=None
TEST=Build and boot to OS in Skyrim. Ensure that the PSP Verstage
timestamps in cbmem -t output are adjusted correctly.
Before this change:
5:start of verified boot 67,890 (69,936)
503:starting to initialize TPM 67,890 (0)
504:finished TPM initialization 67,902 (12)
505:starting to verify keyblock/preamble (RSA) 67,906 (3)
506:finished verifying keyblock/preamble (RSA) 67,984 (77)
511:starting TPM PCR extend 67,984 (0)
512:finished TPM PCR extend 67,992 (7)
513:starting locking TPM 67,992 (0)
514:finished locking TPM 67,995 (3)
6:end of verified boot 67,995 (0)
11:start of bootblock 572,152 (504,156)
After this change:
5:start of verified boot 71,000 (73,040)
503:starting to initialize TPM 71,065 (65)
504:finished TPM initialization 101,506 (30,441)
505:starting to verify keyblock/preamble (RSA) 110,624 (9,118)
506:finished verifying keyblock/preamble (RSA) 297,101 (186,477)
511:starting TPM PCR extend 297,297 (196)
512:finished TPM PCR extend 315,338 (18,041)
513:starting locking TPM 315,341 (3)
514:finished locking TPM 322,922 (7,581)
6:end of verified boot 322,943 (21)
11:start of bootblock 570,296 (247,353)
Change-Id: I3e52bef22f65596152f29c511bed680427660ff5
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78231
Reviewed-by: Tim Van Patten <timvp@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
|
Create the dexi variant of the taranza project by
copying the files to a new directory named for the variant.
BUG=b:303533815
BRANCH=dedede
TEST=util/abuild/abuild -p none -t google/dedede -x -a
make sure the build includes GOOGLE_DEXI
Signed-off-by: Kenneth Chan <kenneth.chan@quanta.corp-partner.google.com>
Change-Id: I708a16cb864dca7309cb0201e7887af7456a4885
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78249
Reviewed-by: David Wu <david_wu@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
- Enable Acoustic noise mitigation
- Set slow slew rate VCCIA and VCCGT to SLEW_FAST_8
- Set FastPkgCRampDisable VCCIA and VCCGT to 1
BUG=b:303533832
TEST=USE="project_joxer emerge-nissa coreboot"
Signed-off-by: Mark Hsieh <mark_hsieh@wistron.corp-partner.google.com>
Change-Id: I575da55b96bf4deacec5c0992eae9930eb0745d6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78256
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Derek Huang <derekhuang@google.com>
|
|
The original code only reserves IOM mmio, but there is other asl
code that requires to program ioe p2sb mmio such as IOE PCIE clk request
control. See \_SB.ECLK.CLKD in src/soc/intel/common/acpi/pcie_clk.asl
TEST=as before: suspend_stress_test 50 cycle pass, type-c display OK
on screebo
Change-Id: Ie55f7975277b390f776e44596c42e426ba9cd235
Signed-off-by: Kane Chen <kane.chen@intel.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78252
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
Measured the I2C frequency meets spec
- I2C0 (TPM): 949.7 Khz
- I2C1 (TouchScreen): 395.8 Khz
- I2C3 (Audio): 387.4 Khz
- I2C5 (Touchpad): 384.8 Khz
BUG=b:303356736
TEST=USE="project_joxer emerge-nissa coreboot"
and check all I2C devices measurement result
Signed-off-by: Mark Hsieh <mark_hsieh@wistron.corp-partner.google.com>
Change-Id: I17dd1cb7800d00669f86fc6e2b350757695da881
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78218
Reviewed-by: Derek Huang <derekhuang@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
Package C-state auto demotion feature allows hardware to determine lower
C-state as per platform policy. Since platform sets performance policy
to balanced from hardware, auto demotion can be disabled without
performance impact.
Also, disabling this feature results soc to enter below PC8 state and
additional power savings ~30mW in Local-Video-Playback scenario.
BUG=b:303546334
TEST=Local build successfully & Boot to OS successfully
- Also check platform enter PC8 state in local video playback
- before this change: # iotools rdmsr 0 0xE2 -> 0x0000000060008008
- After # iotools rdmsr 0 0xE2 -> 0x0000000000008008
Change-Id: Ia4cf4a7cb6bd5eaae26197b55f9385c078960d7b
Signed-off-by: Sukumar Ghorai <sukumar.ghorai@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78250
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Eric Lai <ericllai@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
|
|
Add more fields for PCIe slots status and link control and
slot capabilities.
Change-Id: I64e40ea6bd731cd52ce006224b7c3091d5ef3aac
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78237
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
When advertising C-state using the ACPI _CST object, make sure
to only advertise those that are supported by the CPU.
Downgrade if it's not and make sure to not advertise duplicate
states.
Add debug prints for the finally selected mapping of ACPI
C-state vs Intel CPU C-state.
Test: Tested on Lenovo X220.
All C-states are still advertised as all are supported.
Change-Id: Iaaee050e0ce3c29c12e97f5819a29f485a7946c2
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78194
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Make the code look like on newer platforms. This doesn't change
functionality.
Test: Lenovo X220 still boots and advertises all C-states as
before.
Change-Id: Ie7076d11720d55a4ac11318cbbdab9f75d08e15e
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78193
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
According to the BWG C-states are processor specific
and BIOS must check if a C-state is supported at all.
Print the supported C-states in before ACPI _CNT generation.
Test: Tested on Lenovo X220 using Intel i5-2540M.
All C-states are reported as supported.
Change-Id: I713712a1a104714cbf3091782e564e7e784cf21d
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78133
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add a function to get the number of substates supported by
an Intel CPU C-state.
Test: Can read out the supported C-state substates.
Change-Id: Ie57e87609ea5d6ec6f37154e8b84f1e9574aa4a9
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78224
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
It was changed from a fixed size-1 array to a flexible array
in commit 242bac0e162c ("…: Use C99 flexible arrays") which resulted
in a change to the serialized format as the header size was no longer
the same.
That broke other tools that read CBFS files, like diffoscope
https://github.com/NixOS/nixpkgs/issues/256896
Change-Id: I4199dcc4823469c5986ac967a55b1c85cc62f780
Signed-off-by: Ivan Jager <aij+git@mrph.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78239
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Patrick Georgi <patrick@coreboot.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Based on the power sequence of the panel [1], the power on T3 sequence
VSN to RESET should be larger than 1ms. Because the Power IC descending
slope takes 2ms, actual measurement needs 3ms to meet the timing of
panel sequence.
[1] HX83102-J02_Datasheet_v03.pdf
BUG=b:302212730
BRANCH=corsola
TEST=emerge-staryu coreboot chromeos-bootimage and boot the panel
Change-Id: I488c746d1fcfc165125b0ecccb0bccbb99231b00
Signed-off-by: Cong Yang <yangcong5@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78185
Reviewed-by: Ruihai Zhou <zhouruihai@huaqin.corp-partner.google.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Yidi Lin <yidilin@google.com>
|
|
Intel platforms use Low Power Idle Table (LPIT) to enumerate platform
Low Power Idle states. There are two types of low power residencies
a) CPU PKG C10 - read via MSR (Function fixed hardware interface)
b) Platform Controller Hub (PCH) SLP_S0 - read via memory mapped IO
Ref. https://www.uefi.org/sites/default/files/resources/Intel_ACPI_Low_Power_S0_Idle.pdf,
section 2.2.1: value of 0 indicates that counter runs at TSC frequency.
Ref. Intel 64 and IA-32 Architectures Software Developer’s Manual (Vol 4)
MSR 0x632: PC10 residency counter is at same frequency as the TSC.
Whereas slp_s0 residency counter running in different frequency.
BUG=b:300440936
TEST=check kernel cpuidle sysfs are created after kernel boot
cat /sys/devices/system/cpu/cpuidle/low_power_idle_cpu_residency_us
cat /sys/devices/system/cpu/cpuidle/low_power_idle_system_residency_us
Change-Id: Ibde764551a21b9aecb1c269948f4823548294711
Signed-off-by: Sukumar Ghorai <sukumar.ghorai@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78177
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
This consolidates the bp, tb, cmp, srp0 and srp1 variables under the new
spi_flash_bpbits struct to allow treating them as one unit in the
refactoring to follow.
Change-Id: I2a1a77fb73047df733498c0fa8b8de1153c3b09e
Signed-off-by: Daniel Gröber <dxld@darkboxed.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42113
Reviewed-by: Jakub Czapiga <czapiga@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Currently the block protection bits are being passed around as
individual arguments. We will use this new struct to replace the
corresponding arguments in the winbond_bpbits_to_region and
winbond_set_write_protection functions.
Change-Id: I02828b1f764aea29374e794001e74cdc86a94c92
Signed-off-by: Daniel Gröber <dxld@darkboxed.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42112
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jakub Czapiga <czapiga@google.com>
|
|
This fixes building lenovo/x200 with VBOOT.
All supported CPUs have enough L2 cache to support this.
Change-Id: Ifd6a16ce36c86349955cd7b7ddb3f74a19c17c4d
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/71905
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Quandiso reserve bit 11 for mipi camera usage.
BUG=b:300574047
BRANCH=firmware-nissa-15217.B
TEST=emerge-nissa coreboot
Change-Id: Id4343083f0d69a49c642657d165ceac349cd7422
Signed-off-by: Robert Chen <robert.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78213
Reviewed-by: Shawn Ku <shawnku@google.com>
Reviewed-by: Eric Lai <ericllai@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=b:300573763
BRANCH=firmware-nissa-15217.B
TEST=emerge-nissa coreboot
Change-Id: Iff8167695c302f7b58976516d651a81f1a429bee
Signed-off-by: Robert Chen <robert.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77754
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shawn Ku <shawnku@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
When service center repair touchscreen or touchpad will change
compatible device not specific one, the fw_config probe mechanism is not
convenient for service center. Removing touchscreen and touchpad
fw_config probe for the purpose.
BUG=b:297840605
BRANCH=firmware-nissa-15217.B
TEST=emerge-nissa coreboot chromeos-bootimage
Change-Id: I66f12ae478f74c019c53ee5e77f7e0f9c324e758
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77538
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Derek Huang <derekhuang@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Turn off GPP_H13 (EN_PP3300_SD_X) in s0ix for power saving. It reduces
about 3mW of power consumption in s0ix on pirrha proto board.
BUG=b:300845527
TEST=Built and verified GPP_H13 voltage was 0V in s0ix.
Also verified SD card worked after s0ix for 20 times.
Change-Id: I5ec53820276e50f5b8b01584595118cf2dc4c95c
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77998
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Derek Huang <derekhuang@google.com>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
This patch reverses ISH UART pin configuration to allow ISH to enter
into suspend mode. This UART port is for debugging purposes.
BUG=b:302612549
TEST=On Google/rex platform with ISH enabled, do suspend_stress_test
This test must pass
Signed-off-by: Bernardo Perez Priego <bernardo.perez.priego@intel.com>
Change-Id: I8aba45420744a3990e1f9637c3b31ea2e0f78f87
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78049
Reviewed-by: Tanu Malhotra <tanu.malhotra@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
This patch implements an API to report the presence of an external
display on Intel silicon. The API uses information from the transcoder
and framebuffer to determine if an external display is connected.
For example, if the transcoder is attached to any DDI ports other than
DDI-A (eDP), and the framebuffer is initialized, then it is likely
that an external display is present.
This information can be used by payloads to determine whether or not
to power on the display, even if eDP is not initialized.
BUG=b:299137940
TEST=Build and boot google/rex
Scenarios:
Booting with eDP alone: has_external_display value is 0
Booting with eDP + HDMI: has_external_display value is 0
Booting with HDMI alone: has_external_display value is 1
Booting with USB-C display alone: has_external_display value is 1
Change-Id: I77436940978c7fa9368d79394b46a5e794c32e42
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78080
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
This patch introduces a new coreboot table entry named
"has_external_display" to understand if external display is attached.
This information is useful to prevent graceful shutdown by payload
when the LID is closed but an external display is present.
This piece of the information will be gathered by coreboot and passed
into the payload using this new entry aka external_display because
payload (i.e., deptcharge) doesn't have any other way to determine
if external display is available.
BUG=b:299137940
TEST=Able to build and boot google/rex.
w/o this patch:
LID closed and external display attached (HDMI) in developer mode
(GBB 0x39):
> System is powered off by depthcharge
w/ this patch:
LID closed and external display attached (HDMI) in developer mode
(GBB 0x39):
> Booted to OS and device is alive/usable
Change-Id: I0fa7eee4c5a50371a7a66c6ca1ac2c7d046d010b
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77796
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Intel GFX IP TRANS_DDI_FUNC_CTL register bit definitions have changed
since Tiger Lake.
This register is used to map ports and pipes to display controllers,
so reflecting the correct status is important for detecting physical
display end point devices.
This patch ensures that ADL, MTL, and TGL SoCs choose GMA version 2 to
properly reflect the updated port and pipe register definitions.
BUG=b:299137940
TEST=Build and boot google/rex successfully.
Change-Id: Ie2082747d18a5f136f410b1019be4d6c801617b1
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78079
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
This commit updates the port select bit definitions for the
TRANS_DDI_FUNC_CTL registers in the Intel GMA driver to accommodate
the changes introduced since TGL SoC.
Specifically, the following changes were made:
- Updated the DDI select bit definitions from 3-bits (bit 28-30) to
4-bits (bit 27-30).
- Introduces `INTEL_GMA_VERSION_2` config to accommodate the port and
pipe related differences between previous generation GMA register
(TRANS_DDI_FUNC_CTL) to the current generation GMA register.
This commit backports the change from the following upstream patch:
https://patchwork.freedesktop.org/patch/msgid/20190713010940.17711-3-
lucas.demarchi@intel.com
BUG=b:299137940
TEST=Able to build and boot google/rex.
Change-Id: I815ffa90c2e235afd70baa7e3837e1f9af89b1b0
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78078
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
Set USB port which corresponds PORTSCN/PORTSCXUSB3 register bits for
enable USB wake.
BUG=b:302230434
TEST=Verify USB-A device could wake up Boxy
Signed-off-by: Joey Peng <joey.peng@lcfc.corp-partner.google.com>
Change-Id: I0f6300dc6bbb6fb8226151e49e38f0450b1e71b7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78144
Reviewed-by: Derek Huang <derekhuang@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Set USB port which corresponds PORTSCN/PORTSCXUSB3 register bits for enable USB wake.
The physical USB slot is 6, USB2 port5 for Bluetooth, total USB2 port num is 7, USB3 keep 6.
BUG=b:300844110
TEST=Verify USB-A device could wake up Taranza
Signed-off-by: Sheng-Liang Pan <sheng-liang.pan@quanta.corp-partner.google.com>
Change-Id: Ied92c4a70bc594bd189dcb942f1a445412509464
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78068
Reviewed-by: Ricky Chang <rickytlchang@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Reka Norman <rekanorman@chromium.org>
|
|
Use the common UWES ACPI method to enable wake from USB. The only
difference to other SoCs is that JSL only has 8 USB2 ports, so the USB3
PORTSC register offset is different.
BUG=b:300844110
TEST=When enabled on taranza, all USB2 and USB3 ports can wake from
suspend
Change-Id: Ibc90246965d5d809123e954847543d28d78498a5
Signed-off-by: Reka Norman <rekanorman@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78086
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sheng-Liang Pan <sheng-liang.pan@quanta.corp-partner.google.com>
|
|
The ACPI methods for enabling USB wake are identical on ADL, CNL and
SKL. Move them to a common ASL file so they can be reused more easily
on other SoCs.
Also move the USB_PORT_WAKE_ENABLE macro used to create enable bitmasks
in devicetree to a common header.
BUG=b:300844110
TEST=Use abuild to build kinox, puff, and fizz with and without this
change. Check the generated dsdt.aml is unchanged.
Change-Id: Iabdfe2bece7fafc284ddf04382f1bbcacc370cce
Signed-off-by: Reka Norman <rekanorman@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78085
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
|
|
This panel is never actually enabled on Geralt. The derived project
won't use this panel either. Therefore, remove this panel support.
BUG=none
BRANCH=none
TEST=emerge-geralt coreboot
Change-Id: I97ed5b341724ed42098b2c17d0eb75eab881dbb1
Signed-off-by: Yidi Lin <yidilin@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78210
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
The tolerance of ADC voltage table is too small. Update the table values
accordring to the suggestion from the hardware team. The patch is
prepared for the derived projects. There is no actual issue now.
BRANCH=none
BUG=b:301908091
TEST=check firmware screen
Change-Id: I3bde30b6bbe79c81e276f23f4110715c3278d42c
Signed-off-by: Yidi Lin <yidilin@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78209
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
Add VCM power control to configure 2.8V and reset pin, and VCM can
be powered on/off properly.
BUG=b:292907385
TEST=Run ITS test
Change-Id: I242025836fd50076a40ffcc4e5d4a5d5bc6fb4d0
Signed-off-by: Serin Yeh <serin.yeh@intel.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78170
Reviewed-by: Derek Huang <derekhuang@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Certain devices are enabled in Alder Lakes chipset.cb, so remove
them from the devicetree.
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: I929af0bed6c2e1024b4787424a8fe466edce5a36
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78198
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I1b0052b569b575fec7893322dec0280c9f1ed79f
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78197
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
