summaryrefslogtreecommitdiff
path: root/src
AgeCommit message (Collapse)Author
2012-11-08RTC: Don't clear pending interrupt in resume pathDuncan Laurie
The linux kernel relies on the RTC reporting pending interrupts if the RTC alarm was used to wake the system. If we clear these flags here then the rtc-cmos driver in the kernel will think that no interrupts are pending and will not re-start the timerqueue to handle the alarm timerqueue node. This flag doesn't exist in SMM but the rtc code is compiled there. Since rtc_init() is not called by SMM it is guarded with an ifdef. I performed several thousand suspend/resume cycles without seeing an issue where hwclock was unable to read from /dev/rtc. There still is a potential kernel issue where the timerqueue can stall but this makes that much less likely to happen on resume. Change-Id: I5a343da4ce5c4c8ec4783b4e503869ccfa5077f0 Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: http://review.coreboot.org/1741 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2012-11-08smi: make tseg_relocate check pointer offsetDuncan Laurie
In case tseg_relocate() is called again on a pointer we should not relocate it again. Change-Id: Ida1f9c20dc94b448c773b14d8864afe585369119 Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: http://review.coreboot.org/1740 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2012-11-08elog: add extended management engine eventDuncan Laurie
We are seeing ME disabled and ME error events on some devices and this extended info can help with debug. Also fix a potential issue where if the log does manage to get completely full it will never try to shrink it because the only call to shrink the log happens after a successful event write. Add a check at elog init time to shrink the log size. Change-Id: Ib81dc231f6a004b341900374e6c07962cc292031 Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: http://review.coreboot.org/1739 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2012-11-08spi: fix erase in SMM while SPIBAR is lockedDuncan Laurie
The handling of write enable was not entirely correct, the opcode needs to be skipped when the controller is locked down. Addresses were not getting set properly for erase commands which seemed to mostly work when the previous command had set an address. Tested by adding events to the event log at runtime on a freslhy flashed device (with locked down SPI controller) until the log log shrink happens to ensure it does not hang: hexdump -C elog.event.kernel_clean 00000000 01 00 00 00 ad de 00 00 00 00 for x in $(seq 1 232); do cat elog.event.kernel_clean > /sys/firmware/gsmi/append_to_eventlog done mosys eventlog list | tail -6 154 | 2012-09-01 13:54:43 | Kernel Event | Clean Shutdown 155 | 2012-09-01 13:54:43 | Kernel Event | Clean Shutdown 156 | 2012-09-01 13:54:43 | Kernel Event | Clean Shutdown 157 | 2012-09-01 13:54:43 | Kernel Event | Clean Shutdown 158 | 2012-09-01 13:54:43 | Log area cleared | 1030 159 | 2012-09-01 13:54:43 | Kernel Event | Clean Shutdown Change-Id: I3a50dae54422a9ff37daefce3632f8bcbe4eb89f Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: http://review.coreboot.org/1717 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2012-11-08Make option rom init more verboseStefan Reinauer
When bringing up VGA by running the option rom it's sometimes useful to get more information about the mode that gets set, or the reason why the mode could not be set or a picture could not be displayed. Also prefix the output from VBE mode setting with VBE: Copying VGA ROM Image from fff0fd78 to 0xc0000, 0x10000 bytes Real mode stub @00000600: 867 bytes Calling Option ROM... int15_handler: INT15 function 5fac! ... Option ROM returned. VBE: Getting information about VESA mode 4161 VBE: resolution: 1280x1024@16 VBE: framebuffer: d0000000 VBE: Setting VESA mode 4161 VGA Option ROM has been loaded Change-Id: I2be11f095dc62ed3c99e0d4272ad9d6521608a44 Signed-off-by: Stefan Reinauer <reinauer@google.com> Reviewed-on: http://review.coreboot.org/1714 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2012-11-08ELOG: Find flash base in FMAP if possibleDuncan Laurie
Now that we have FMAP support in coreboot use it to find the offset in flash for ELOG to use. If coreboot has elog configured with a smaller size then use that over the FMAP size. This is because I set aside a 16KB region in the FMAP but we only use 4KB of it to keep the impact to boot/resume speed to a minimum. FMAP: Found "FMAP" version 1.0 at ffe10000. FMAP: base = 0 size = 800000 #areas = 32 FMAP: area RW_ELOG found FMAP: offset: 3f0000 FMAP: size: 16384 bytes FMAP: No valid base address, using 0xff800000 ELOG: base=0x003f0000 base_ptr=0xffbf0000 ELOG: MEM @0x00190ad8 FLASH @0xffbf0000 ELOG: areas are 4096 bytes, full threshold 3072, shrink size 1024 Change-Id: I3d826812c0f259d61f41b42797c58dd179f9f1c8 Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: http://review.coreboot.org/1706 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2012-11-07ELOG: Don't disable SPI controller lockdownDuncan Laurie
Now that WREN prefix is handled properly ELOG is able to write when the SPI controller is locked down. To test, ensure that runtime SPI write via ELOG is successful by checking the event log for a kernel shutdown reason code: 5 | 2012-08-27 11:09:48 | Kernel Event | Clean Shutdown 6 | 2012-08-27 11:09:50 | System boot | 26 7 | 2012-08-27 11:09:50 | System Reset Change-Id: If6d0dced7cb0f5ca7038b3d758f31b856826d30b Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: http://review.coreboot.org/1712 Reviewed-by: Marc Jones <marcj303@gmail.com> Tested-by: build bot (Jenkins)
2012-11-07SPI: opmenu special case for WREN as atomic prefixDuncan Laurie
The code that attempts to use the opmenu needs to have a special case for write enable now that it is handled as an atomic prefix and not as a standalone opcode. To test, ensure that runtime SPI write via ELOG is successful by checking the event log for a kernel shutdown reason code: 5 | 2012-08-27 11:09:48 | Kernel Event | Clean Shutdown 6 | 2012-08-27 11:09:50 | System boot | 26 7 | 2012-08-27 11:09:50 | System Reset Change-Id: I527638ef3e2a5ab100192c5be6e6b3b40916295a Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: http://review.coreboot.org/1710 Reviewed-by: Marc Jones <marcj303@gmail.com> Tested-by: build bot (Jenkins)
2012-11-07RTC: Write build date in BCD when clearing RTC CMOSDuncan Laurie
Check the RTC on boot after RTC battery failure and ensure that the reported build date matches what is reported: > grep ^rtc /proc/driver/rtc rtc_time : 01:00:21 rtc_date : 2012-08-16 Change-Id: If23f436796754c68ae6244ef7633ff4fa0a93603 Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: http://review.coreboot.org/1709 Reviewed-by: Marc Jones <marcj303@gmail.com> Tested-by: build bot (Jenkins)
2012-11-07SMI: Change order of SMI_EN and PM1_EN initDuncan Laurie
This appears to fix an infrequent resume hang on Ivybridge. Tested on 2 devices with 15k suspend/resume cycles each Change-Id: I53618bc7966824413f1720a2be3cbd2550e29473 Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: http://review.coreboot.org/1704 Reviewed-by: Marc Jones <marcj303@gmail.com> Tested-by: build bot (Jenkins)
2012-11-07EC: Prepare to read and log last post code from previous bootDuncan Laurie
(elog portion, support in EC code pending) - Use a new EC command to read the last post code from the previous boot - If the post code is not well-known final boot or resume code then log it Change-Id: Id6249e9a182243eb87c777edd56f48de72125e77 Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: http://review.coreboot.org/1703 Reviewed-by: Marc Jones <marcj303@gmail.com> Tested-by: build bot (Jenkins)
2012-11-07SandyBridge/IvyBridge: Use flash map to find MRC cacheStefan Reinauer
Until now, the MRC cache position and size was hard coded in Kconfig. However, on ChromeOS devices, it should be determined by reading the FMAP. This patch provides a minimalistic FMAP parser (libflashmap was too complex and OS centered) to allow reading the in-ROM flash map and look for sections. This will also be needed on some partner devices where coreboot will have to find the VPD in order to set up the device's mac address correctly. The MRC cache implementation demonstrates how to use the FMAP parser. Change-Id: I34964b72587443a6ca4f27407d778af8728565f8 Signed-off-by: Stefan Reinauer <reinauer@google.com> Reviewed-on: http://review.coreboot.org/1701 Reviewed-by: Marc Jones <marcj303@gmail.com> Tested-by: build bot (Jenkins)
2012-11-07Add missing newline in error messageStefan Reinauer
This is purely cosmetic. All error messages in the Sandybridge raminit code printed a newline at the end. Change-Id: I880d291928291d487039850a2a3d53a1101124ba Signed-off-by: Stefan Reinauer <reinauer@google.com> Reviewed-on: http://review.coreboot.org/1699 Reviewed-by: Marc Jones <marcj303@gmail.com> Tested-by: build bot (Jenkins)
2012-11-07rtc: add explicit dependency on build.hVincent Palatin
build.h is generated at build time, with highly parallel builds, we might try to compile the rtc driver too early. Change-Id: I9a2681484d58b67ed3061669fbdf52ac5ad14dab Signed-off-by: Vincent Palatin <vpalatin@chromium.org> Reviewed-on: http://review.coreboot.org/1698 Reviewed-by: Marc Jones <marcj303@gmail.com> Tested-by: build bot (Jenkins)
2012-11-07rtc: erase CMOS memory after power failureVincent Palatin
When a power failure happens on the RTC rail, the CMOS memory (including the RTC registers) is filled with garbage. So, we erase the full first bank (112 bytes) and we reset the RTC date to the build date. To test, disconnect the CMOS battery to produce an RTC power failure, then boot the machine and observe the RTC date is the build date using "cat /sys/class/rtc/rtc0/date" Change-Id: I684bb3ad5079f96825555d4ed84dc0f7914e9884 Signed-off-by: Vincent Palatin <vpalatin@chromium.org> Reviewed-on: http://review.coreboot.org/1697 Reviewed-by: Marc Jones <marcj303@gmail.com> Tested-by: build bot (Jenkins)
2012-11-07AMD G34 CPU: change lapic_id in northbridge.c to accommodate G34 CPUSiyuan Wang
Each G34 socket has two node. Previous lapic algorithm is written for the CPU which has one node per socket. I test the code on h8qgi with 4 family 15 CPUs(8 cores per CPU). The topology is: socket 0 --> Node 0, Node 1 socket 2 --> Node 2, Node 3 socket 1 --> Node 4, Node 5 socket 3 --> Node 6, Node 7 Each node has 4 cores. I change the code according to this topology. Change-Id: I45f242e0dfc61bd9b18afc952d7a0ad6a0fc3855 Signed-off-by: Siyuan Wang <SiYuan.Wang@amd.com> Signed-off-by: Siyuan Wang <wangsiyuanbuaa@gmail.com> Reviewed-on: http://review.coreboot.org/1659 Tested-by: build bot (Jenkins) Reviewed-by: Marc Jones <marcj303@gmail.com>
2012-11-07CMOS: Move MRC seed offset into upper bankDuncan Laurie
This will allow the lower bank to be cleared without impacting the ability to suspend/resume. Change-Id: Iaec3c9e7e40c334053c814eaddd1f614df245a73 Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: http://review.coreboot.org/1696 Reviewed-by: Marc Jones <marcj303@gmail.com> Tested-by: build bot (Jenkins)
2012-11-07rtc: force mc146818 register D to a correct valueVincent Palatin
On Panther Point PCH (and maybe cougar point), when some of the register D reserved bits are set, the RTC starts misbehaving (e.g. incrementing the year byte every second). There are probably undocumented features implemented behind those bits. Let's reset register D to a known state to ensure we get the expected RTC behavior. Change-Id: I7e2c2a2c6130a974bccb3d760b41eaa579a58b67 Signed-off-by: Vincent Palatin <vpalatin@chromium.org> Reviewed-on: http://review.coreboot.org/1695 Reviewed-by: Marc Jones <marcj303@gmail.com> Tested-by: build bot (Jenkins)
2012-11-07Fix CONFIG_ use in i8254.cStefan Reinauer
We always define CONFIG_ variables, even if they're not set. Hence, remove the check whether CONFIG_UDELAY_TIMER2 is defined Change-Id: Iefdf2389941f2cc63ae4f13ac6b213da4c96b201 Signed-off-by: Stefan Reinauer <reinauer@google.com> Reviewed-on: http://review.coreboot.org/1694 Reviewed-by: Marc Jones <marcj303@gmail.com> Tested-by: build bot (Jenkins)
2012-11-07Add POST code for "All devices initialized"Stefan Reinauer
Right now we only had a post code for "All devices enabled" which was emitted at the wrong time (after the device initialize stage rather than the device enable stage) Change-Id: Iee82bff020de844c7095703f8d6521953003032c Signed-off-by: Stefan Reinauer <reinauer@google.com> Reviewed-on: http://review.coreboot.org/1693 Reviewed-by: Marc Jones <marcj303@gmail.com> Tested-by: build bot (Jenkins)
2012-11-07Move global variable check to MakefileStefan Reinauer
Our linker script for romstage checks for global variables and makes the build fail if there are any (on non-AMD systems). This is great, but having the build fail without any indication which variables are global is not very useful. Moving the check to the Makefile allows us to let the linking stage succeed and reveil which variable names end up in the data and bss sections of the binary. To test, add "int foo;" as the first line in src/mainboard/samsung/lumpy/romstage.c and build coreboot for Lumpy. See the build break the following way: LINK cbfs/fallback/romstage_null.debug Forbidden global variables in romstage: 00006a84 B foo Change-Id: I3c8780888f46a6577ffd36bcea317997b4f84f6f Signed-off-by: Stefan Reinauer <reinauer@google.com> Reviewed-on: http://review.coreboot.org/1692 Tested-by: build bot (Jenkins) Reviewed-by: Marc Jones <marcj303@gmail.com>
2012-11-07Leave power control registers unlockedSameer Nanda
To allow easy experimentation with thermals, leave power control registers unlocked. Change-Id: Ia53065f3f220c2faed58e7d53e60c3f169ae58ec Signed-off-by: Sameer Nanda <snanda@chromium.org> Reviewed-on: http://review.coreboot.org/1688 Tested-by: build bot (Jenkins) Reviewed-by: Marc Jones <marcj303@gmail.com>
2012-11-07Fix whitespace issue with help message in Kconfig fileDave Frodin
Every line of text after a 'help' label in a Kconfig file must have the same whitespace preceding it, otherwise it's no longer considered help text. Change-Id: I97093bee72b295b315d78d4c26d7186bf1017fda Signed-off-by: Dave Frodin <dave.frodin@se-eng.com> Reviewed-on: http://review.coreboot.org/1687 Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org> Tested-by: build bot (Jenkins)
2012-11-07AMD rd890 late.c: Don't enable PCIe ports after PCIe init.Siyuan Wang
PCIE devices are detected and initialized by the AMD PCIe init functions, which is in cimx rd890. The parameters are read from devicetree.cb before PCIe init. Now, all bridges and devices are trained on the device 0.0 enable. After PCIe init, the PCIe ports with devices are on and the PCIe ports without devices are off. so resources may be allocated correctly during the rest of the PCI scan. But if the devicetree was being used to enable/disable devices after initialization, the problems would arise. Take a look at the serial log: do_pci_scan_bridge for PCI: 00:02.0 PCI: pci_scan_bus for bus 01 PCI: pci_scan_bus returning with max=001 do_pci_scan_bridge returns max 1 do_pci_scan_bridge for PCI: 00:03.0 PCI: pci_scan_bus for bus 02 PCI: pci_scan_bus returning with max=002 do_pci_scan_bridge returns max 2 do_pci_scan_bridge for PCI: 00:04.0 PCI: pci_scan_bus for bus 03 PCI: pci_scan_bus returning with max=003 do_pci_scan_bridge returns max 3 PCI bridge 02.0, 03.0 and 04.0 are not inserted devices, but these bridges are still scanned. This is not correct. Change-Id: I87dac5f062c6926081970ed0c5f26a7e3f447395 Signed-off-by: Siyuan Wang <SiYuan.Wang@amd.com> Signed-off-by: Siyuan Wang <wangsiyuanbuaa@gmail.com> Reviewed-on: http://review.coreboot.org/1640 Tested-by: build bot (Jenkins) Reviewed-by: Marc Jones <marcj303@gmail.com>
2012-11-07AMD agesa family15: PCI domain should scan bus from 0x18.0Siyuan Wang
There are four mainboards using agesa family15 code: Supermicro h8scm and h8qgi, Tyan s8226 and AMD dinar. All of these boards' PCI domain starts from 0x18.0. Take h8scm as an example, PCI devices from 0.0 to 0x14.5 is under 0x18.0. Now, the PCI domain's scan bus function stats from 0.0. This would result to the PCI devices be scanned twice. Because when the function run to device 18.0, it would scan from 0.0 again. This issue would result to 2 problems: 1) PCI device may be assigned two different PCI address. If this happenned on VGA device, coreboot maybe not load vga bios correctly. 2) coreboot initializes rd890's IO APIC twice. So this patch scans from 0x18.0 and could resolve the problems above. Change-Id: I90fbdf695413fd24c7a5e3e9b426dc7ca6e128b1 Signed-off-by: Siyuan Wang <SiYuan.Wang@amd.com> Signed-off-by: Siyuan Wang <wangsiyuanbuaa@gmail.com> Reviewed-on: http://review.coreboot.org/1639 Tested-by: build bot (Jenkins) Reviewed-by: Marc Jones <marcj303@gmail.com>
2012-11-06acpi: Add support for DMAR tables (Intel IOMMU support)Patrick Georgi
Adds lowlevel handling of DMAR tables for use by mainboards' ACPI code. Not much automagic (yet). Change-Id: Ia86e950dfcc5b9994202ec0e2f6d9a2912c74ad8 Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com> Reviewed-on: http://review.coreboot.org/1654 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2012-11-06Drop redundant CHIP_NAME in mainboard.cKyösti Mälkki
Compose the name from Kconfig strings instead. As the field is for debug print use only, a minor change in the output should do no harm. The strings no longer include word "Mainboard". Change-Id: Ifd24f408271eb5a5d1a08a317512ef00cb537ee2 Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: http://review.coreboot.org/1635 Tested-by: build bot (Jenkins) Reviewed-by: Patrick Georgi <patrick@georgi-clan.de> Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2012-11-06smsc/lpc47n227: Make early_serial usablePatrick Georgi
This is the smallest possible change to make early_serial.c compile when included from romstage.c. early_serial could be reworked to be built as separate unit (romstage-y), but that should be done for all SuperIOs, not some individual outlier. Change-Id: I90ee66b43c9677b86b1b5d6fcc8febfbe58d80dd Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com> Reviewed-on: http://review.coreboot.org/1686 Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2012-11-06cpu/intel/model_1067x: Add proper c-state/p-state/thermal supportNico Huber
Change-Id: I853454e8f5617fb7af5dddd7288bdeeacc7b1b8e Signed-off-by: Nico Huber <nico.huber@secunet.com> Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com> Reviewed-on: http://review.coreboot.org/1663 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2012-11-06intel/socket_BGA956: enable speedstep, CAR, MMX, SSEPatrick Georgi
All of these capabilities exist on all CPUs supported on this socket. Change-Id: I54f34e48e34bb6ab5b9954ab7ece8c2c3a1a8e67 Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com> Reviewed-on: http://review.coreboot.org/1664 Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2012-11-06Add name field for deviceKyösti Mälkki
The constant field "name" in chip_operations is common to multiple different devices within a chip and cannot reflect the actual device as found on the platform. The intention is that a driver sets dev->name as part of the device enumeration sequence with the detected hardware type and revision. The field is for debug print use only. Change-Id: Ib7bf90ba3c618ad0cb715d80d6a937ceaae0adcf Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: http://review.coreboot.org/1634 Tested-by: build bot (Jenkins) Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
2012-11-05Overhaul speedstep codeNico Huber
This adds proper support for turbo and super-low-frequency modes. Calculation of the p-states has been rewritten and moved into an extra file speedstep.c so it can be used for non-acpi stuff like EMTTM table generation. It has been tested with a Core2Duo T9400 (Penryn) and a Core Duo T2300 (Yonah) processor. Change-Id: I5f7104fc921ba67d85794254f11d486b6688ecec Signed-off-by: Nico Huber <nico.huber@secunet.com> Reviewed-on: http://review.coreboot.org/1658 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2012-11-05Fix some indentation flaws and break very long linesNico Huber
Change-Id: I3efef6bc8f519382ffdd92eb10b4bcd1a4361ba9 Signed-off-by: Nico Huber <nico.huber@secunet.com> Reviewed-on: http://review.coreboot.org/1657 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2012-11-02remove enable_cache() of 3 mainboardsSiyuan Wang
Because enable cache is added at the end of disable_cache_as_ram, ( http://review.coreboot.org/#/c/1662/2/src/cpu/amd/agesa/cache_as_ram.inc ) enable_cache() should be removed. The 3 mainboards are: amd parmer, amd thatcher and tyan s8226 Change-Id: If870ca07d2e97b9e860a2e2315f551251c7a4ed2 Signed-off-by: Siyuan Wang <SiYuan.Wang@amd.com> Signed-off-by: Siyuan Wang <wangsiyuanbuaa@gmail.com> Reviewed-on: http://review.coreboot.org/1669 Reviewed-by: Marc Jones <marcj303@gmail.com> Tested-by: build bot (Jenkins)
2012-11-02Persimmon: disable the unconnected Full-Speed USB portDave Frodin
Change-Id: Ia3824059a38412896ed2be0c8714018b2291c9f8 Signed-off-by: Dave Frodin <dave.frodin@se-eng.com> Reviewed-on: http://review.coreboot.org/1660 Tested-by: build bot (Jenkins) Reviewed-by: Marc Jones <marcj303@gmail.com>
2012-11-02AMD agesa: add enable cache at the end of disable_cache_as_ramSiyuan Wang
add this code according to src/include/cpu/x86/cache.h ,line 92, functin enable_cache() Change-Id: Ida96a98397eeed98dd61ca979e8c5a33bf00f9e5 Signed-off-by: Siyuan Wang <SiYuan.Wang@amd.com> Signed-off-by: Siyuan Wang <wangsiyuanbuaa@gmail.com> Reviewed-on: http://review.coreboot.org/1662 Tested-by: build bot (Jenkins) Reviewed-by: Marc Jones <marcj303@gmail.com>
2012-11-02Correct FSB reading in speedstep ACPINico Huber
We parsed the MSR the wrong way, and didn't support some valid values. Change-Id: Ia42e3de05dd76b6830aaa310ec82031d36def3a0 Signed-off-by: Nico Huber <nico.huber@secunet.com> Reviewed-on: http://review.coreboot.org/1656 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2012-11-02Fix some issues with new "reference" toolchainStefan Reinauer
Unfortunately the reference tool chain was updated without ever even testing it on an abuild run. This broke a number of ports. This change gets coreboot at least compiling again for all supported systems. Change-Id: I92c7cbc834de6d792fdab86b75df339e2874c52e Signed-off-by: Stefan Reinauer <reinauer@google.com> Reviewed-on: http://review.coreboot.org/1670 Reviewed-by: Ronald G. Minnich <rminnich@gmail.com> Tested-by: build bot (Jenkins)
2012-11-01Merge cpu/intel/acpi.h into cpu/intel/speedstep.hNico Huber
We had only some MSR definitions in there, which are used in speedstep related code. I think speedstep.h is the better and less confusing place for these. Change-Id: I1eddea72c1e2d3b2f651468b08b3c6f88b713149 Signed-off-by: Nico Huber <nico.huber@secunet.com> Reviewed-on: http://review.coreboot.org/1655 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2012-10-30Add support for socket LGA775Stefan Tauner
Change-Id: Ia7ef3a4cbc3638a9c9a48b297e392e4e655b6e6b Signed-off-by: Stefan Tauner <stefan.tauner@gmx.at> Reviewed-on: http://review.coreboot.org/1581 Tested-by: build bot (Jenkins) Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
2012-10-30Fix ExecuteFinalHltInstruction function in f15h family codeKostr
Current ExecuteFinalHltInstruction function doesn't work well. (at least in configuration Supermicro board with Orochi AMD Opteron processors (model OS6234WKTCGGU)) System reboots when trying to halt core 2,4,6,8 or 10 (OS6234WKTCGGU is 12 core processor) Based on this information, i think that code doesn't really work with f15 compute unit (CU) system. Replacing ExecuteFinalHltInstruction function with analogous function from f15tn family code fix this problem. Both functions written from the same cahalt.asm file, but f15tn version seems more completed Change-Id: I3942abcdf21f1b86a44c01cc477714e44a40b9cf Signed-off-by: Kostr <aladyshev@nicevt.ru> Reviewed-on: http://review.coreboot.org/1569 Tested-by: build bot (Jenkins) Reviewed-by: Siyuan Wang <wangsiyuanbuaa@gmail.com> Reviewed-by: Marc Jones <marcj303@gmail.com>
2012-10-30AMD SB800: PCIE slots on PersimmonZheng Bao
Enable the PCIE bridge which is connected to the PCIE slot. Change-Id: I1b3fb59990e06d7bc7cf19639f2b93dbb7bf9b3e Signed-off-by: Zheng Bao <zheng.bao@amd.com> Signed-off-by: zbao <fishbaozi@gmail.com> Reviewed-on: http://review.coreboot.org/1098 Tested-by: build bot (Jenkins) Reviewed-by: Dave Frodin <dave.frodin@se-eng.com> Reviewed-by: Marc Jones <marcj303@gmail.com>
2012-10-29Drop get_smbios_data from chip_operationsKyösti Mälkki
We only want to add data once per device. Using the one in chip_operations is not very usable anyway, as different devices under the same chip directory would need to output entirely different sets of data. Change-Id: I96690c4c699667343ebef44a7f3de1f974cf6d6d Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: http://review.coreboot.org/1492 Reviewed-by: Duncan Laurie <dlaurie@chromium.org> Tested-by: build bot (Jenkins)
2012-10-29Fix reading of number of interrupts for IO-APICsNico Huber
The number read from the io-apic register represents the index of the highest interrupt redirection entry, i.e. the number of interrupts minus one. Change-Id: I54c992e4ff400de24bb9fef5d82251078f92c588 Signed-off-by: Nico Huber <nico.huber@secunet.com> Reviewed-on: http://review.coreboot.org/1624 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2012-10-29Hide all _ROM_RUN Kconfig options if the payload is SeaBIOSPeter Stuge
The options are shown regardless of payload if CONFIG_EXPERT is set. Change-Id: I12c81ce41a0e300e852481424eadc83f281863bf Signed-off-by: Peter Stuge <peter@stuge.se> Reviewed-on: http://review.coreboot.org/1638 Tested-by: build bot (Jenkins) Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
2012-10-29Run option ROMs in coreboot by default only if the payload is not SeaBIOSPeter Stuge
Change-Id: I29fb86ff3a3187b720ce5ef246c4eeee696ab5cd Signed-off-by: Peter Stuge <peter@stuge.se> Reviewed-on: http://review.coreboot.org/1637 Tested-by: build bot (Jenkins) Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
2012-10-29Clarify that _ROM_RUN Kconfig options control if ROMs are run by corebootPeter Stuge
Also clarify that enabling these options is generally not desirable if using SeaBIOS as payload since the option ROMs are run by SeaBIOS with more complete BIOS interrupt services available than coreboot. Change-Id: Ic4a45c351a4933aedad08d70a088eab04ca35b05 Signed-off-by: Peter Stuge <peter@stuge.se> Reviewed-on: http://review.coreboot.org/1636 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2012-10-28IEI PM-LX2-800-R10: Added preliminary mainboard supportRicardo Martins
Details for this board are available at http://usa.ieiworld.com/product_groups/industrial/content.aspx?gid=00001000010000000001&cid=09050662496936266123&id=09034367569861123956 Support for the IT8888 PCI to ISA bridge will be added in a later patch. Change-Id: Iaefe47f5ad405a56d230c929e5850156eb0f60ae Signed-off-by: Ricardo Martins <rasmartins@gmail.com> Reviewed-on: http://review.coreboot.org/1152 Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com> Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2012-10-27Take care of NULL chip_ops->nameKyösti Mälkki
Change-Id: Ic44915cdb07e0d87962eff0744acefce2a4845a2 Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: http://review.coreboot.org/1626 Tested-by: build bot (Jenkins) Reviewed-by: Patrick Georgi <patrick@georgi-clan.de> Reviewed-by: Peter Stuge <peter@stuge.se>
2012-10-26iwave/iWRainbowG6: use 16bit access for a register which is not 32bit alignedSebastian Andrzej Siewior
The PCI registers should be accessed aligned and 0x62 is not 32bit aligned therefore this patch changes it to a 16bit access. Change-Id: I00725a4569f471eedb061834f626911b42e734fb Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Reviewed-on: http://review.coreboot.org/1631 Reviewed-by: Patrick Georgi <patrick@georgi-clan.de> Tested-by: build bot (Jenkins)
2012-10-26northbridge/sch: move the \n so it reads a little betterSebastian Andrzej Siewior
Without this, the output of "Setting up ACPI…" continues right after the output of stepping. Change-Id: I2ad7cc3e55884ff509600b01274258b8e8250981 Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Reviewed-on: http://review.coreboot.org/1632 Reviewed-by: Patrick Georgi <patrick@georgi-clan.de> Tested-by: build bot (Jenkins)
2012-10-26iwave/iWRainbowG6: remove USE_DCACHE_RAMSebastian Andrzej Siewior
This is not available as a config option anymore. Change-Id: Icac173d62928423a08671321ec21d4af82c5cded Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Reviewed-on: http://review.coreboot.org/1630 Reviewed-by: Patrick Georgi <patrick@georgi-clan.de> Tested-by: build bot (Jenkins)
2012-10-26northbridge/sch: read the size of main memory from the proper registerSebastian Andrzej Siewior
I don't know if the size main memory supposed to be in PCI(0,0) reg 0x9c but it is not written there. The size of memory is written in src/northbridge/intel/sch/raminit.c to SCH port(2, 8, 4) (look for "Setting up TOM"). Change-Id: Iea04a5185bda56f61d1c382533d5a0dac429ebbd Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Reviewed-on: http://review.coreboot.org/1629 Reviewed-by: Patrick Georgi <patrick@georgi-clan.de> Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org> Tested-by: build bot (Jenkins)
2012-10-26northbridge/sch: Read the GPU memory from the correct PCI deviceSebastian Andrzej Siewior
The GGC register which contains the size of memory that is used for GPU is in PCI device 2,0 and not 0,0. It is set to to 4MiB in src/mainboard/iwave/iWRainbowG6/romstage.c. Change-Id: Ie9f1cc60544ecd9cad770f34c83c33564a6129d4 Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Reviewed-on: http://review.coreboot.org/1628 Reviewed-by: Patrick Georgi <patrick@georgi-clan.de> Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org> Tested-by: build bot (Jenkins)
2012-10-26northbridge/sch: don't overwrite hightables with GPU / TSEG memorySebastian Andrzej Siewior
Without this, the hightables are placed just before the end of memory. However we might have the GPU memory located at the exact same spot, that is in the last 4 MiB. So without this patch, this area won't remain marked as "CONFIGURATION TABLES" within coreboot's memory table but becomes "RESERVED" because it is part of the PCI(2,0) device. Change-Id: Ibd111c167c2f6ac03b0ba68581a74ecbd2c9c160 Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Reviewed-on: http://review.coreboot.org/1627 Reviewed-by: Patrick Georgi <patrick@georgi-clan.de> Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org> Tested-by: build bot (Jenkins)
2012-10-24Trinity: Initialize the pointer prior to using itZheng Bao
Change-Id: I2f10909a626fb64c7f95663ddd79a3b899f73bc4 Signed-off-by: Zheng Bao <zheng.bao@amd.com> Signed-off-by: Zheng Bao <fishbaozi@gmail.com> Reviewed-on: http://review.coreboot.org/1606 Tested-by: build bot (Jenkins) Reviewed-by: Dave Frodin <dave.frodin@se-eng.com> Reviewed-by: Marc Jones <marcj303@gmail.com>
2012-10-22change conflicted typedef in src/vendorcode/amd/agesa/f15/Porting.hSiyuan Wang
src/vendorcode/amd/agesa/f15/Porting.h has some conflicted typedef with src/include/cpu/amd/common/cbtypes.h. These conflicted defines can lead to errors. Change-Id: Idad0794018bf0bd0e4e52a5aa062a12766d56c8e Signed-off-by: Siyuan Wang <SiYuan.Wang@amd.com> Signed-off-by: Siyuan Wang <wangsiyuanbuaa@gmail.com> Reviewed-on: http://review.coreboot.org/1592 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2012-10-16Update SeaBIOS stable to the release-1.7.1 commitPeter Stuge
Change-Id: I0dffe89c31e45914f795d9ad8efb787b5fdbb7a8 Signed-off-by: Peter Stuge <peter@stuge.se> Reviewed-on: http://review.coreboot.org/1583 Tested-by: build bot (Jenkins)
2012-10-10bachmann/ot200: Fix wrong IRQ number for PIRQDChristian Gmeiner
The used FPGA on the device triggers PIRQD for the membrane keyboard. The used linux driver for the keyboard uses the fixed IRQ number of 7. In order not to touch the linux driver and be compatible with proprietary BIOS change the irq_table in coreboot. Change-Id: If5bc929eb48bb1eafd401941ebb7d34cf5862c35 Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com> Reviewed-on: http://review.coreboot.org/1571 Tested-by: build bot (Jenkins) Reviewed-by: Peter Stuge <peter@stuge.se>
2012-10-10iei/kino-780am2: Turn on PCIe bridge to 2nd ethernet controller.Dave Frodin
Change-Id: I35fa94bafcf7c835081b57acf031a2fb334d353d Signed-off-by: Dave Frodin <dave.frodin@se-eng.com> Reviewed-on: http://review.coreboot.org/1570 Tested-by: build bot (Jenkins) Reviewed-by: Peter Stuge <peter@stuge.se>
2012-10-08hpet: common ACPI generationPatrick Georgi
HPET's min ticks (minimum time between events to avoid losing interrupts) is chipset specific, so move it to Kconfig. Via also has a special base address, so move it as well. Apart from these (and the base address was already #defined), the table is very uniform. Change-Id: I848a2e2b0b16021c7ee5ba99097fa6a5886c3286 Signed-off-by: Patrick Georgi <patrick@georgi-clan.de> Reviewed-on: http://review.coreboot.org/1562 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org> Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
2012-10-08Every chip must have chip_operationsKyösti Mälkki
Forcing this rule, chip_ops can be added in the static devicetree regardless of the existence of the chip.h files. Change-Id: Iec1c23484e85cab3f80a34f2b082088f38ac4de9 Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Signed-off-by: Patrick Georgi <patrick@georgi-clan.de> Reviewed-on: http://review.coreboot.org/1472 Tested-by: build bot (Jenkins)
2012-10-07Take care of NULL chip_ops->nameKyösti Mälkki
Change-Id: I62b1c497d23ec2241efb963e7834728085824016 Signed-off-by: Patrick Georgi <patrick@georgi-clan.de> Reviewed-on: http://review.coreboot.org/1565 Tested-by: build bot (Jenkins) Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
2012-10-07Fix typo in mPGA603 socketKyösti Mälkki
Change-Id: I7a49d5fc13fb605a47c3c1662758ebd5935e7780 Signed-off-by: Patrick Georgi <patrick@georgi-clan.de> Reviewed-on: http://review.coreboot.org/1564 Tested-by: build bot (Jenkins) Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
2012-10-07Remove chip.h files without config structureKyösti Mälkki
Also deletes files not included in build: src/southbridge/amd/cimx/sb700/chip_name.c src/southbridge/amd/cimx/sb800/chip_name.c src/southbridge/amd/cimx/sb900/chip_name.c Change-Id: I2068e3859157b758ccea0ca91fa47d09a8639361 Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: http://review.coreboot.org/1473 Tested-by: build bot (Jenkins) Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com> Reviewed-by: Marc Jones <marcj303@gmail.com>
2012-10-07Revert order in VGA device choiceKostr
Before change "Simplify VGA card discovery" (http://review.coreboot.org/#/c/1255/) coreboot was setting up VGA for the last found VGA device. After this change it setting up VGA for the first found. This change broke compatibility to my Supermicro H8QGI board. Revert order back to old to save compatibility for this board (and maybe any other boards) Change-Id: Id5f2be60f95298059651c26133806e2694ff60aa Signed-off-by: Kostr <aladyshev@nicevt.ru> Reviewed-on: http://review.coreboot.org/1561 Tested-by: build bot (Jenkins) Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
2012-10-05Mainboard: Fix IO-HUB link number in Dinar mainboardKostr
According to file "northbridge.c" in family 15h code IO-HUB should be placed on link_lsit[0] in devicetree.cb. This hack in "northbridge.c" was made to satisfy both f10 and f15 cpu's. Change-Id: I4754235bd38239460347b0dc4a82cd4e58ae7cd0 Signed-off-by: Kostr <aladyshev@nicevt.ru> Reviewed-on: http://review.coreboot.org/1540 Tested-by: build bot (Jenkins) Reviewed-by: Marc Jones <marcj303@gmail.com>
2012-10-05Provide access to smaller registers in eregsPatrick Georgi
This is in preparation for sharing interrupt handlers between YABEL and x86emu. Change-Id: Iff92c1d899b8ada20972731944341805a49b6326 Signed-off-by: Patrick Georgi <patrick@georgi-clan.de> Reviewed-on: http://review.coreboot.org/1560 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2012-10-05Use mainboard_interrupt_handlers everywherePatrick Georgi
The previous commit provides a mainboard_interrupt_handlers implementation YABEL with identical semantics to the x86emu one, so let's use it in both cases. This eliminates the need for the int15_install() indirection, so let's drop that, too. Generated using the following coccinelle patch and manual cleanups (empty #if/#endif): @@ type T; identifier FUNCARR; expression INT, HANDLER; @@ -typedef T yabel_handleIntFunc; -extern yabel_handleIntFunc FUNCARR[256]; -FUNCARR[INT] = HANDLER; +mainboard_interrupt_handlers(INT, &HANDLER); @@ @@ -void int15_install(void) -{ -mainboard_interrupt_handlers(0x15, &int15_handler); -} @@ @@ -void int15_install(void) -{ -mainboard_interrupt_handlers(0x15, &int15_handler); ... mainboard_interrupt_handlers(0x15, &int15_handler); -} @@ @@ -int15_install(); +mainboard_interrupt_handlers(0x15, &int15_handler); Change-Id: I70fd780d7ebf1564a2ff7d7148411673f6de113c Signed-off-by: Patrick Georgi <patrick@georgi-clan.de> Reviewed-on: http://review.coreboot.org/1559 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2012-10-05YABEL: Common API to register interrupt handlersPatrick Georgi
Provide (mostly) the same API for registering interrupt handlers as with x86emu. Change-Id: I1364b08d9043039550786a1758508ae088813aa3 Signed-off-by: Patrick Georgi <patrick@georgi-clan.de> Reviewed-on: http://review.coreboot.org/1558 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2012-10-04add tyan s8226: add a new mainboardSiyuan Wang
our code supports tyan s8226 now, which has two cpus on the board the cpu socket is C32. The details of tyan s8226 is: http://www.tyan.com/product_SKU_spec.aspx?ProductType=MB&pid=679&SKU=600000190 the test result of this mainboard is: 1) boot Ubunbu 11.10, kernel 3.0.9. there is no err and warnings in dmesg. 2) boot windows7 x64 successfully. 3) use fwts to test the bios, there are 268 pass and 14 failed 4) pcie and usb slots are ok. 5) all network interfaces are ok. Change-Id: I7d8534f20b4f3c16322a5c5ba2e3fba4b4f3e608 Signed-off-by: Siyuan Wang <SiYuan.Wang@amd.com> Signed-off-by: Siyuan Wang <wangsiyuanbuaa@gmail.com> Reviewed-on: http://review.coreboot.org/1495 Tested-by: build bot (Jenkins) Reviewed-by: Marc Jones <marcj303@gmail.com>
2012-10-04pirq_routing: Allow routing with more than 4 PIRQ linksAlexandru Gagniuc
pirq_routing_irqs assumed that only four links are available for PIRQ routing, INTA to INTD. Some chipsets provide more, up to INTH. When pirq_routing_irqs found a link number greater than 4 in the pirq table, it would not assign that IRQ. This is a shame, as it limits the flexibility of routing IRQs. Make the maximum number of links a Kconfig variable, and modify the code to respect it. This works beatifully on the VX900, which provides 8 routable interrupts. While we're at it, also refactor pirq_routing_irqs, and add some much needed comments. Rename pirq_routing_irqs to pirq_route_irqs to demistify the role of this function. The copyrights added were determined from git log filename. Change-Id: I4b565315404c65b871406f616474e2cc9e6e013e Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com> Reviewed-on: http://review.coreboot.org/1482 Tested-by: build bot (Jenkins)
2012-10-02Fix compilation without CONFIG_WRITE_HIGH_TABLES.Denis 'GNUtoo' Carikli
Without that fix we have: CC boot/hardwaremain.ramstage.o src/boot/hardwaremain.c: In function 'hardwaremain': src/boot/hardwaremain.c:136:6: error: 'cbmem_post_handling' undeclared (first use in this function) src/boot/hardwaremain.c:136:6: note: each undeclared identifier is reported only once for each function it appears in src/boot/hardwaremain.c:137:3: error: implicit declaration of function 'cbmem_post_handling' [-Werror=implicit-function-declaration] cc1: all warnings being treated as errors make: *** [build/boot/hardwaremain.ramstage.o] Error 1 When compiling without CONFIG_WRITE_HIGH_TABLES Change-Id: Ie45f684a6db0ab55ef469bfcef57e539ae7e994c Signed-off-by: Denis 'GNUtoo' Carikli <GNUtoo@no-log.org> Reviewed-on: http://review.coreboot.org/1533 Tested-by: build bot (Jenkins) Reviewed-by: Peter Stuge <peter@stuge.se>
2012-09-28AMD Hudson: Printf the high address as unsigned integerZheng Bao
Some 32 bit machines print integer higher than 0x80000000 as negative number. Change-Id: Ieb512ed2a7499ce7e91e45e4075d4f119780b57d Signed-off-by: Zheng Bao <zheng.bao@amd.com> Signed-off-by: Zheng Bao <fishbaozi@gmail.com> Reviewed-on: http://review.coreboot.org/1547 Tested-by: build bot (Jenkins) Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
2012-09-25HAVE_HIGH_TABLES is gonePatrick Georgi
... but no-one told intel/sch. Change-Id: I68eaae6910bd6fc579c35b5bc038b9597cd1b3e7 Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com> Reviewed-on: http://review.coreboot.org/1537 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2012-09-24AMD hudson: Round the float pointing number to integerZheng Bao
Try sh> printf %d 0x005500AA | LC_ALL=C awk '{printf("%c%c%c%c", \ $1 % 256, $1/256 % 256, $1/65536 % 256, $1/16777216);}' | \ od -Ax -t x On Linux with gawk, we get 000000 005500aa 000004 On FreeBSD with nongnu-awk, we get 000000 000055aa 000002 In awk, all the numbers are floating point number. So division doesn't round the result from 0.75 (3/4) to 0. And, There is a fact that, for the FreeBSD awk, sh> awk 'BEGIN {printf("%c", 0.75)}'; produces nothing, instead of 0. Here we need to convert the floating point number to integer by int(X), which is an awk built-in function, instead of GNU extension. Change-Id: I3470d5f13e7ea59a978d5575a54c0d56368dc78d Signed-off-by: Zheng Bao <zheng.bao@amd.com> Signed-off-by: Zheng Bao <fishbaozi@gmail.com> Reviewed-on: http://review.coreboot.org/1529 Tested-by: build bot (Jenkins) Reviewed-by: Peter Stuge <peter@stuge.se>
2012-09-19cimx sb700: change Platform.h to remove some warningsSiyuan Wang
TRACE has redefined warnings in src/southbridge/amd/cimx/sb700/Platform.h, so we do some changes to remove such warnings. Change-Id: I24979e08b83434f91a8fa37cd9f16303fa0b298d Signed-off-by: Siyuan Wang <SiYuan.Wang@amd.com> Signed-off-by: Siyuan Wang <wangsiyuanbuaa@gmail.com> Reviewed-on: http://review.coreboot.org/1499 Tested-by: build bot (Jenkins) Reviewed-by: Marc Jones <marcj303@gmail.com>
2012-09-19agesa fam15 northbridge: change lapic_id to accommodate two CPUsSiyuan Wang
According to http://review.coreboot.org/gitweb?p=coreboot.git;a=blob;f=src/vendorcode/amd/agesa/f15/Proc/CPU/cpuApicUtilities.c;hb=HEAD#l273 line 273, adjust apic id to accommodate two CPUs. The Tyan S8226 has two CPU sockets, and the current code just finds one CPU's cores. we adjust apic_id in cpu_bus_scan so as to find all CPUs. Change-Id: Ib3263fc6f5508f744b81e8e388fde9ccd9b51851 Signed-off-by: Siyuan Wang <SiYuan.Wang@amd.com> Signed-off-by: Siyuan Wang <wangsiyuanbuaa@gmail.com> Reviewed-on: http://review.coreboot.org/1498 Tested-by: build bot (Jenkins) Reviewed-by: Marc Jones <marcj303@gmail.com>
2012-09-19C32 legacy code: change CONFIG_CPU_AMD_SOCKET_C32 to ↵Siyuan Wang
CONFIG_CPU_AMD_SOCKET_C32_NON_AGESA Currently the C32 has some legacy boards which use the old C32 code. We need to seperate them. CONFIG_CPU_AMD_SOCKET_C32 was used in legacy code before. But it is not a good idea, so we change the code as follows: So we use CONFIG_CPU_AMD_SOCKET_C32 to identify mainboard which uses agesa code, and use CONFIG_CPU_AMD_SOCKET_C32_NON_AGESA to identify mainboard which uses legacy code. Change-Id: If6114bf8912e78b7732f25a1adfb2e4d8eb10ee4 Signed-off-by: Siyuan Wang <SiYuan.Wang@amd.com> Signed-off-by: Siyuan Wang <wangsiyuanbuaa@gmail.com> Reviewed-on: http://review.coreboot.org/1497 Tested-by: build bot (Jenkins) Reviewed-by: Marc Jones <marcj303@gmail.com>
2012-09-17AMD Hudson: use awk to calulate instead of exprZheng Bao
Command expr in some systems only take 32bit as integer, which value is at 0x7FFFFFFF ~ -0x80000000. Use awk as alternate way to calculate. And some system doesnt take hex value in Makefile, even in awk instruction. Change-Id: Ie35d6a5b96eea4192bd9cab857af4d4dcb37b9ed Signed-off-by: Zheng Bao <zheng.bao@amd.com> Signed-off-by: Zheng Bao <fishbaozi@gmail.com> Reviewed-on: http://review.coreboot.org/1527 Tested-by: build bot (Jenkins) Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
2012-09-17Set SMBIOS mainboard version based on i2c eepromChristian Gmeiner
In the field there are different hardware revisions and some of them have problems with UDMA as a resistor is missing. We can detect this situation in coreboot and e.g. the linux kernel can take this knowledge and disable UDMA. Change-Id: Ib75cad7acedbc1dc65378bb9bfc3f353cbe21427 Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com> Reviewed-on: http://review.coreboot.org/1512 Tested-by: build bot (Jenkins) Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
2012-09-17Add i2c eeprom to device treeChristian Gmeiner
This eeprom is used to store some device relevant informations like hardware revision. Change-Id: I32bda9d5412bc5a96da0edb5ef0b6d1ba4caa2d8 Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com> Reviewed-on: http://review.coreboot.org/1511 Tested-by: build bot (Jenkins) Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
2012-09-13Mahogany_Fam10: Fixes an apparent ACPI VGA resource collision.Dave Frodin
Without this change 64 bit versions of Windows will BSOD. Change-Id: If39627a179c24184b6c956b3a50f692f8a034d2f Signed-off-by: Dave Frodin <dave.frodin@se-eng.com> Reviewed-on: http://review.coreboot.org/1476 Tested-by: build bot (Jenkins) Reviewed-by: Marc Jones <marcj303@gmail.com>
2012-09-13Fix tracing compilation on SMM enabled targets.Rudolf Marek
Disallow tracing while in SMM. Change-Id: Icde17629bb06a615cc48f017fd0cd1f7b720e62d Signed-off-by: Rudolf Marek <r.marek@assembler.cz> Reviewed-on: http://review.coreboot.org/1503 Tested-by: build bot (Jenkins) Reviewed-by: Marc Jones <marcj303@gmail.com>
2012-09-12Fix VT8237S USB IRQ routingRudolf Marek
The M2V-MX SE DSDT has been a copy from Asus A8V-E SE, which has VT8237R. But the stuble change in USB interrupt routing went undetected, although I had some USB troubles on the FOSDEM with low speed devices. Change-Id: Ie724df440e0963f6955b3de57e4687f3ddc7f6ef Signed-off-by: Rudolf Marek <r.marek@assembler.cz> Reviewed-on: http://review.coreboot.org/1505 Tested-by: build bot (Jenkins) Reviewed-by: Marc Jones <marcj303@gmail.com>
2012-09-07superio winbond w83627dhg: add a function which is used on tyan s8226Siyuan Wang
this function is used on serial output of tyan s8226 Change-Id: I5f7fa535b922b224e381886f1bea64623fa549ef Signed-off-by: Siyuan Wang <SiYuan.Wang@amd.com> Signed-off-by: Siyuan Wang <wangsiyuanbuaa@gmail.com> Reviewed-on: http://review.coreboot.org/1494 Tested-by: build bot (Jenkins) Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
2012-09-06IEI/KINO: Fixes an apparent ACPI VGA resource collision.Dave Frodin
Without this change 64 bit versions of Windows will BSOD. Change-Id: Ica4b79d798a269399341868b1c793ce745aa93fc Signed-off-by: Dave Frodin <dave.frodin@se-eng.com> Reviewed-on: http://review.coreboot.org/1480 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2012-09-05VIA Nano: Add support for VIA Nano CPUsAlexandru Gagniuc
Add code to do the following for the VIA Nano CPUs - Update microcode - Set maximum frequency - Initialize power states - Set up cache Attempting to change the voltage or frequency of the CPU without applying the microcode update will hang the CPU, so we only do transitions if we can verify the microcode has been updated. The microcode is updated directly from CBFS. No microcode is included in ramstage. The microcode is not included in this commit. To get the microcode, run bios_extract on the manufacturer supplied BIOS, and look for the file marked "P6 Microcode". Include this file in CBFS. You can have the build system include this file automatically by selecting Expert Mode, then look under 'Chipset' -> 'Include CPU microcode in CBFS' -> Include external microcode file (check) 'Path and filename of CPU microcode' should contain the location of the microcode file previously extracted. Change-Id: I586aaca5715e047b42ef901d66772ace0e6b655e Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com> Reviewed-on: http://review.coreboot.org/1257 Tested-by: build bot (Jenkins)
2012-09-05buildsystem: Make CPU microcode updating more configurableAlexandru Gagniuc
This patch aims to improve the microcode in CBFS handling that was brought by the last patches from Stefan and the Chromium team. Choices in Kconfig - 1) Generate microcode from tree (default) - 2) Include external microcode file - 3) Do not put microcode in CBFS The idea is to give the user full control over including non-free blobs in the final ROM image. MICROCODE_INCLUDE_PATH Kconfig variable is eliminated. Microcode is handled by a special class, cpu_microcode, as such: cpu_microcode-y += microcode_file.c MICROCODE_IN_CBFS should, in the future, be eliminated. Right now it is needed by intel microcode updating. Once all intel cpus are converted to cbfs updating, this variable can go away. These files are then compiled and assembled into a binary CBFS file. The advantage of doing it this way versus the current method is that 1) The rule is CPU-agnostic 2) Gives user more control over if and how to include microcode blobs 3) The rules for building the microcode binary are kept in src/cpu/Makefile.inc, and thus would not clobber the other makefiles, which are already overloaded and very difficult to navigate. Change-Id: I38d0c9851691aa112e93031860e94895857ebb76 Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com> Reviewed-on: http://review.coreboot.org/1245 Tested-by: build bot (Jenkins) Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com> Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
2012-08-30AMD S3: The offset of the nv storage depends on config.hZheng Bao
Change-Id: Ic8410fb706dce677c7218d19030d84b64cda7b7f Signed-off-by: Zheng Bao <zheng.bao@amd.com> Signed-off-by: zheng Bao <fishbaozi@gmail.com> Reviewed-on: http://review.coreboot.org/1485 Tested-by: build bot (Jenkins) Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com> Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
2012-08-30ioapic driver: typedef the ioapic_config struct (TRIVIAL)Alexandru Gagniuc
I use the ioapic_config in my VX900 branch. Typing: struct drivers_generic_ioapic_config *config = (struct drivers_generic_ioapic_config *)dev->chip_info; is clumsy at best, so just create a typedef to mahe this more elegant: ioapic_config_t config = (ioapic_config_t*)ioapic->chip_info; Change-Id: I407899845cfbd847ba6309dd0cf9ef836a607c8e Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com> Reviewed-on: http://review.coreboot.org/1481 Tested-by: build bot (Jenkins) Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
2012-08-28Fix AMD UMA for RS780Kyösti Mälkki
In commit 6b5eb1cc2d1702ff10cd02249d3d861c094f9118 setup of UMA memory region was moved to happen at a later state and this broke UMA with RS780 southbridge. Share the TOP_MEM and UMA settings before any of the PCI or CPU scanning takes place. Change-Id: I9cae1fc2948cbccede58d099faf1dfe49e9df303 Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: http://review.coreboot.org/1488 Tested-by: build bot (Jenkins) Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com> Reviewed-by: Dave Frodin <dave.frodin@se-eng.com> Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
2012-08-28AMD hudson: Complete the missing ruleZheng Bao
Forgot to change the code back after debugging. Change-Id: Iaf58d65c14d53ca77958080faf6ab85d60992226 Signed-off-by: Zheng Bao <zheng.bao@amd.com> Signed-off-by: Zheng Bao <fishbaozi@gmail.com> Reviewed-on: http://review.coreboot.org/1491 Tested-by: build bot (Jenkins) Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
2012-08-27Drop unused ISA Pnp definitionsKyösti Mälkki
These declarations were never or no longer used. Change-Id: Icdbfc0838d5021ea02ab031b643b3fe6361b39b4 Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: http://review.coreboot.org/1489 Reviewed-by: Ronald G. Minnich <rminnich@gmail.com> Tested-by: build bot (Jenkins) Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
2012-08-27SB700/SP5100: This configures the HPET clock period.Dave Frodin
Prior to this change the setting would be zeroes and would cause a BSOD in 64 bit versions of Windows. Change-Id: I2d422ef9667457af53f9fd055799e489ed2b25db Signed-off-by: Dave Frodin <dave.frodin@se-eng.com> Reviewed-on: http://review.coreboot.org/1475 Tested-by: build bot (Jenkins) Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com> Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
2012-08-27AMD Hudson: Move the combining firmware from Python to sh.Zheng Bao
Maybe sooner or later python is not a default tools to build coreboot. Most of the work is done by awk now. GNU extension of gawk is not used, isn't? echo, expr, printf, cat, awk, test, mv are the external tools. If XHCI, IMC or GEC firmware is not available and not defined, this script can skip integrating them. Change-Id: I9944b22b0b755672a46d472c355d138abafd6393 Signed-off-by: Zheng Bao <zheng.bao@amd.com> Signed-off-by: zbao <fishbaozi@gmail.com> Reviewed-on: http://review.coreboot.org/1417 Tested-by: build bot (Jenkins) Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com> Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
2012-08-27Intel model_106cx: change CAR to HT-capableKyösti Mälkki
There are hyper-threading Atom CPUs, those would not enable L2 cache with model_6ex CAR code. Switch to code that can handle different number of threads and cores. Change-Id: I57328c231f8998f45f7b0d26c63b24585f8476dd Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: http://review.coreboot.org/1384 Tested-by: build bot (Jenkins) Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com> Reviewed-by: James Laird <jhl@mafipulation.org> Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
2012-08-27AMD northbridges: factor out CPU allocationKyösti Mälkki
Factor CPU allocation out of AMD northbridge codes. As CPU topology information is required for generation of certain ACPI tables, make this code globally available. For AMDK8 and AMDFAM10 northbridge, there is a possible case of BSP CPU with lapicid!=0. We do not want to leave the lapic 0 from devicetree unused, so always use that node for BSP CPU. Change-Id: I8b1e73ed5b20b314f71dfd69a7b781ac05aea120 Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: http://review.coreboot.org/1418 Tested-by: build bot (Jenkins) Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com> Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
2012-08-27AMD northbridges: rewrite CPU allocationKyösti Mälkki
Use of alloc_find_dev() prevents creation of a device duplicates for device_path and is SMP safe. Reduce scope of variables to make the code more readable and in preparation for refactoring the allocation out of northbridge.c. Change-Id: I153dc1a5cab4f2eae4ab3a57af02841cb1a261c0 Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: http://review.coreboot.org/1186 Tested-by: build bot (Jenkins) Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com> Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
2012-08-25MPTABLE: check for fixed IRQ entries on all pinsSven Schnelle
Don't derive the IRQ pin from the function number. Especially onboard chipset devices don't follow that rule. Instead check and add all fixed IRQ entries. Change-Id: I46c88bad39104c1d9b4154f180f8b3c42df28262 Signed-off-by: Sven Schnelle <svens@stackframe.org> Reviewed-on: http://review.coreboot.org/1461 Tested-by: build bot (Jenkins) Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-12-01 06:50:43 +0000