| Age | Commit message (Collapse) | Author |
|---|
|
Fleex will use SSFC to support RTL5682.
BUG=b:178653122
TEST=abuild
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: Icb06eabe297c5562bd2171b52cc9671c342e6dfd
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51423
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marco Chen <marcochen@google.com>
|
|
Update GPP_A10 and GPP_H17 configuration to meet LTE power sequence
specification.
- FCPO (GPP_A10) should not turned off during warm reset.
BUG=b:177177967
BRANCH=dedede
TEST=Verified LTE power signal waveforms during powering on and off
Change-Id: I469f9c94ebd6bf2b68a0edc74f229158d82d0ef8
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51429
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
I was bugged by spurious "Failed to enable LTR" messages for years.
Looking at the the current algorithm, it is flawed in multiple ways:
* It looks like the author didn't know they implemented a
recursive algorithm (pciexp_enable_ltr()) inside another
recursive algorithm (pciexp_scan_bridge()). Thus, at every
tree level, everything is run again for the whole sub-
tree.
* LTR is enabled no matter if `.set_ltr_max_latencies` is
implemented or not. Leaving the endpoints' LTR settings
at 0: They are told to always report zero tolerance.
In theory, depending on the root-complex implementation,
this may result in higher power consumption than without
LTR messages.
* `.set_ltr_max_latencies` is only considered for the direct
parent of a device. Thus, even with it implemented, an
endpoint below a (non-root) bridge may suffer from the 0
settings as described above.
* Due to the double-recursive nature, LTR is enabled starting
with the endpoints, then moving up the tree, while the PCIe
spec tells us to do it in the exact opposite order.
With the current implementation of pciexp_scan_bridge(), it is
hard to hook anything in that runs for each device from top to
bottom. So the proposed solution still adds some redundancy:
First, for every device that uses pciexp_scan_bus(), we enable
LTR if possible (see below). Then, when returning from the bus-
scanning recursion, we enable LTR for every device and configure
the maximum latencies (if supported). The latter runs again on
all bridges, because it's hard to know if pciexp_scan_bus() was
used for them.
When to enable LTR:
* For all devices that implement `.set_ltr_max_latencies`.
* For all devices below a bridge that has it enabled already.
Change-Id: I2c5b8658f1fc8cec15e8b0824464c6fc9bee7e0e
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51328
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Since no board overrides the weak get_gpe_table function,
gpe_configure_sci wasn't called for any variant, so drop the function.
TEST=none
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I3de204cc808449b625e1fa1e79fe653608e4b88a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51474
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Mathew King <mathewk@chromium.org>
|
|
This change select the Kconfig to pre-allocate the Intel-recommended bus
and memory resources per-PCIe TBT root port for the adlrvp mainboard.
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: Ic56ebab02e50a466662a07d122d8f40eaf16b54b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51461
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change select the Kconfig to pre-allocate the Intel-recommended bus
and memory resources per-PCIe TBT root port for the brya0 mainboard.
TEST=snippet from dmesg logs shows the correct resources being allocated:
PCI: 00:07.0 resource base 27fc00000 size 1c000000 align 20 gran 20 limit 29bbfffff flags 60181202 index 24
PCI: 00:07.0 resource base 83000000 size c200000 align 20 gran 20 limit 8f1fffff flags 60080202 index 20
PCI: 00:07.1 resource base 29bc00000 size 1c000000 align 20 gran 20 limit 2b7bfffff flags 60181202 index 24
PCI: 00:07.1 resource base a0000000 size c200000 align 20 gran 20 limit ac1fffff flags 60080202 index 20
PCI: 00:07.2 resource base 2b7c00000 size 1c000000 align 20 gran 20 limit 2d3bfffff flags 60181202 index 24
PCI: 00:07.2 resource base ac200000 size c200000 align 20 gran 20 limit b83fffff flags 60080202 index 20
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I6b520ae50f19a730263de7918594718f3b4b1c1a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51455
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The Intel ADL BIOS specification #627270 recommends reserving the
following resources for each PCIe TBT root port:
- 42 buses
- 192 MiB Non-prefetchable memory
- 448 MiB Prefetchable memory
Add a mainboard Kconfig which will auto-select these recommended values,
in addition to PCIEXP_HOTPLUG.
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: Icdfa2688d69c2db0f98d0523d5aba42eec1824db
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51460
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The _DSD is generated at runtime using the Intel common pcie
driver, therefore remove it from the ASL files.
BUG=b:182522802, b:182478306
TEST=boot into latest kernel, no thunderbolt driver errors
seen
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: Iee25a77bf5cc6636f46a5c32f3eeabe8524e0a04
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51454
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The _DSD is generated at runtime using the Intel common USB4
driver, therefore remove it from the ASL files.
BUG=b:182522802, b:182478306
TEST=boot into latest kernel, no thunderbolt driver errors
seen
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I77dc283aeb5f52191255137e941487cf68cb7970
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51453
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add touchpad into devicetree for blipper.
BUG=b:172787208
BRANCH=dedede
TEST=built blipper firmware and verified touchpad function
the kernel log: found RMI device, manufacturer: Synaptics
Change-Id: I2c9b61ba9d282f994e2f756bafe4af1091d4d617
Signed-off-by: Zanxi Chen <chenzanxi@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51188
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Done for consistency with other platforms. This also drops redundant S3
resume logging, as `southbridge_detect_s3_resume` already prints it.
Tested on Asrock B85M Pro4, still boots and still resumes from S3.
Change-Id: Id96c5aedad80702ebf343dd0a351fbd4e7b1c6c1
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51438
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
The `HPET_ADDRESS` Kconfig option has the same value. Use it instead.
Change-Id: I268e949d4396aa20e38f719b36cc4e6226efe082
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49743
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
This reverts commit 87a1bd696d47f80101e46132efae8cad8cfe5c7e.
Reason for revert: skin temperature is overheating due to boost time is too long
BUG=b:175364713
TEST=1. emerge-zork coreboot
2. run balance performance and skin temperature test => pass
Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com>
Change-Id: I31db06f4bcb986398e7bd2ac2858ffbedb257e2b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51391
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Reviewed-by: Daniel Kurtz <djkurtz@google.com>
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
|
|
MT8192 devapc supports remapping domains.
There may be different domain bit for different subsys.
For example, domain bit in INFRA is 4-bit, while in MMSYS,
domain bit is 2-bit. For INFRA master to access MM registers,
the domain bit will change from 4 to 2 and need to be remapped.
In this patch we have remapped:
1. TINYSYS (3-bit to 4-bit)
- domain 3 to domain 3
- others to domain 15
2. MMSYS slave (4-bit to 2-bit)
- domain X to domain X, for X = 0 ~ 3
- others to domain 0
Change-Id: Id10a4c0bdf141cc76a386159896c861d0dc302aa
Signed-off-by: Nina Wu <nina-cm.wu@mediatek.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49790
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
The SKU ID for Asurada should come from AP ADC channel 5 and 6.
BUG=None
TEST=make; boots on asurada
Change-Id: I6a00c555f20aca4cd7f8bcee46ee81c17ef6ca3c
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51405
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
Move the initialization from bootblock to romstage for following reasons:
- Follow MT8183 initialization sequence.
- PMIC and RTC functions are only called after verstage.
- Reduce bootblock size.
- PMIC initialization setting is complex and may need to be changed by
an RW firmware update.
TEST=boot to kernel successfully
Change-Id: I3e4c3f918639590ffc73076450235771d06aae91
Signed-off-by: Yidi Lin <yidi.lin@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51409
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Xi Chen <xixi.chen@mediatek.com>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
|
|
BUG=b:180531661
TEST=builds
Signed-off-by: Mathew King <mathewk@chromium.org>
Change-Id: I5feeead1dcb368c5173901f5cab411f439dffede
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51475
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Let the linker do its job.
This fixes building with !CONFIG_PCIEXP_HOTPLUG on some platforms.
Change-Id: I46560722dcb5f1d902709e40b714ef092515b164
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51417
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
BUG=b:181690884
TEST=builds
Signed-off-by: Mathew King <mathewk@chromium.org>
Change-Id: I8ceeb8db24be34588b370c13d865753f095e4be6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51472
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
To use this, Enable "CONFIG_RUN_FSP_GOP" in the platform's Kconfig.
BUG=b:171234996
TEST=Boot Majolica with GOP graphics
Change-Id: Ic9401cc93ee50fb7dbd84fe26ef24306a1673f58
Signed-off-by: Nikolai Vyssotski <nikolai.vyssotski@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51422
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Mathew King <mathewk@chromium.org>
|
|
The Picasso APUs advertise 23 MCA banks in the lower byte of the
IA32_MCG_CAP MSR, which is more than the 7 core MCA banks.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I3e1c8ed437820b350c78b0517e6521582002ee1e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51477
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
The bank names were copied over from Stoneyridge, but they don't match
for Picasso.
TEST=Checked the Picasso PPR.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ia86cf3874f8b16b007bad46535af6dafb776fbdd
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51476
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This enables the standard library method of adding SPDs to CBFS.
BUG=b:178715165
TEST=Build
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: I2ec94fd866409e1dfa5cb65f6960ea07cbe22f2a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51022
Reviewed-by: Mathew King <mathewk@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add the option to build guybrush firmware with support for EM100.
This will assist in bringup of the new board.
BUG=b:180723776
TEST=builds
Signed-off-by: Mathew King <mathewk@chromium.org>
Change-Id: I2246d2952f341cd8fff8fd486cf989cdb7929411
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51071
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Since not all mainboards based on the Cezanne SoC have to support ACPI
resume, select this option in the mainboard's Kconfig and not in the
SoC's Kconfig.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I988276ccb5b61837d7f3f015d1d1aba783324b02
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51305
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Needed to get the _SX ASL methods.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I6323ba413a21d9d867727dbb28340e6df807c86a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51303
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Currently, `check-fmap-16mib-crossing` compares the offset and end of
each SPI flash region to 16MiB to ensure that no region is placed
across this 16MiB boundary from the start of SPI flash. What really
needs to be checked is that the region isn't placed across the 16MiB
boundary from the end of BIOS region. Thus, current check works only
if the SPI flash is 32MiB under the assumption that the BIOS region
is mapped at the top of SPI flash. However, this check will not work
if a flash part greater than 32MiB is used.
This change replaces the hardcoded boundary value of 16MiB with a
value calculated by subtracting 16MiB from the SPI flash size (if it
is greater than 16MiB). This calculated value is used as the boundary
that no region defined in the flashmap should be placed across.
The assumption here is that BIOS region is always placed at the top of
SPI flash. Hence, the standard decode window would be from
end_of_flash - 16M to end_of_flash (because end_of_flash =
end_of_bios_region). Currently, there is no consistency in the name
used for BIOS region in flashmap layout for boards in
coreboot. But all Intel-based boards (except APL and GLK) place BIOS
region at the end of SPI flash. Since APL and GLK do not support the
extended window, this check does not matter for these platforms.
Change-Id: Icff83e5bffacfd443c1c3fbc101675c4a6f75e24
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51359
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Perform some cosmetical changes:
* Override the first prerequisite so we can use `$<`.
* Add/remove whitspace to align things (recipe needs to be indented
by a single tab only).
* We can use shell variables inside double quotes. To make the
end of the variable name clear, use braces, e.g. "${x}".
NB. Most of the double quotes are unnecessary. They only change
the way the script would be failing in case of spurious whitespace.
* Break some lines doing multiple things at once.
* To reduce remaining clutter, put reading numbers into a shell
function.
And functional changes:
* No need to spawn `cat`, the shell can redirect input as well as
output (using `<`).
* To read a number from the `fmap_config.h`, we spawned 4 processes
where a single one can achieve the same. With one exception: GNU
awk refuses to parse hex numbers by default. Luckily, it turned
out that we don't need intermediate decimal numbers: Shells can
do arithmetic with hex values as well.
Change-Id: Ia7bfba0d7864fc091ee6003e09b705fd7254e99b
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51325
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Currently, if everything worked fine, `$fail` will be unset, leading
to the following `if` statement:
if [ -eq 1 ]
Resulting in the error message:
/bin/sh: line 9: [: -eq: unary operator expected
Fix this by removing the whole `if`, we can just use `exit`.
Change-Id: I1bc7508d2a45a2bec07ef46b9c5d9d0b740fbc74
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51324
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This adds the Guybrush APCBs into the AMD firmware binary.
BUG=b:182510885
TEST=Build
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: Iba40cab1d68e9f8d7291e7d715be185a3b6249f3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51418
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mathew King <mathewk@chromium.org>
|
|
Pass PCI_VGA_RAM_IMAGE_START as VBIOS image pointer for GOP driver.
BUG=b:171234996
Change-Id: I504f808d85d8084e6f32f73cebf02fb0f784cd73
Signed-off-by: Nikolai Vyssotski <nikolai.vyssotski@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51421
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Pass PCI_VGA_RAM_IMAGE_START as VBIOS image pointer for GOP driver.
BUG=b:171234996
BRANCH=Zork
Change-Id: I49adcacf2abb914e460fbc87b488a22dca8c8af2
Signed-off-by: Nikolai Vyssotski <nikolai.vyssotski@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51420
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Load VBIOS in pci set_resources to PCI_VGA_RAM_IMAGE_START (0xc0000)
since pci_dev_init() will not load it in GOP case (VGA_ROM_RUN is not
set). Add Cezanne GFX PID.
BUG=b:171234996
BRANCH=Zork
Change-Id: I4a6fea9b6cd60c862e15ed2ed539869c0f9bd363
Signed-off-by: Nikolai Vyssotski <nikolai.vyssotski@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49867
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
BUG=b:180507937
TEST=builds
Signed-off-by: Mathew King <mathewk@chromium.org>
Change-Id: Icb8aba87390475cad7a2a9911c3832a59c987b65
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51240
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
BUG=b:180507937
TEST=guybrush builds without globalnvs in dsdt.asl
Signed-off-by: Mathew King <mathewk@chromium.org>
Change-Id: I3ffe94f7b575126e61245bed9c9560313df2d725
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51291
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=b:181961514, b:180721208
TEST=builds
Signed-off-by: Mathew King <mathewk@chromium.org>
Change-Id: I0d22de977f09cbf46b28243d9f0c1e9a36e1398f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51295
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Justin Frodsham <justin.frodsham@amd.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Configure early GPIOs in verstage if it is run in PSP otherwise
configure them in bootblock.
BUG=b:181961514, b:180721208
TEST=builds
Signed-off-by: Mathew King <mathewk@chromium.org>
Change-Id: Ib9410089592776ffe198901f2de914fd04bdbade
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51348
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
BUG=b:181961514
TEST=builds
Signed-off-by: Mathew King <mathewk@chromium.org>
Change-Id: I289a2ad1adc5dcc33c5863d6138f66b9b6dc6590
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51294
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Replace the existing, odd looking, unordered definitions used for
LTR configuration with the usual names used by upstream libpci.
TEST=Built google/brya0 with BUILD_TIMELESS=1: no changes.
Fixes: Code looked like UEFI copy-pasta. Header file was a mess.
Change-Id: Icf666692e22730e1bdf4bcdada433b3219af568a
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51327
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Rename `set_L1_ss_latency` to what it does: `set_ltr_max_latencies`.
TEST=Built google/brya0 with BUILD_TIMELESS=1: no changes.
Change-Id: I7008aa18bf80d6709dce1b2d3bfbb5ea407a0574
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51326
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This UPD will be used to pass VBIOS buffer pointer to FSP PEI GOP
driver.
BUG=b:171234996
BRANCH=Zork
Change-Id: I0c5d4a9d96e5c3d47e262072b689ed62e59129b3
Signed-off-by: Nikolai Vyssotski <nikolai.vyssotski@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49866
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I6fb53d88a840a782af7502660ff85205f84523b8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51416
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I32fd9b7165306266613e8497b5d07473b5fea02d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51415
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
gpe_configure_sci has a size_t type parameter, so we need to include
types.h instead of stdint.h here.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I2879d5cf27c432871a2b9c5c90bdd539b97f9d3e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51414
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
CB:49896 added support in `intel_microcode_find()` to cache the found
microcode for faster subsequent accesses. This works okay when the
function succeeds in finding the microcode on BSP. However, if for any
reason, `cpu_microcode_blob.bin` does not contain a valid microcode
for the given processor, then the logic ends up attempting to find
microcode again and again every time it is called (because
`ucode_updates` is set to NULL on failed find, thus retriggering the
whole find sequence every time). This leads to a weird race condition
when multiple APs are running in parallel and executing this
function.
A snippet of the issues observed in the scenario described above:
```
...
microcode: Update skipped, already up-to-date
...
Microcode header corrupted!
...
```
1. AP reports that microcode update is being skipped since the current
version matches the version in CBFS (even though there is no matching
microcode update in CBFS).
2. AP reports microcode header is corrupted because it thinks that the
data size reported in the microcode is larger than the file read from
CBFS.
Above issues occur because each time an AP calls
`intel_microcode_find()`, it might end up seeing some intermittent
state of `ucode_updates` and taking incorrect action.
This change fixes this race condition by separating the logic for
finding microcode into an internal function `find_cbfs_microcode()`
and maintaining the caching logic in `intel_microcode_find()` using a
boolean flag `microcode_checked`.
BUG=b:182232187
TEST=Verified that `intel_microcode_find()` no longer makes repeated
attempts to find microcode from CBFS if it failed the first time.
Change-Id: I8600c830ba029e5cb9c0d7e0f1af18d87c61ad3a
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51371
Reviewed-by: Patrick Rudolph
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
1. Follow GT7375P Programming Guide_Rev.0.6 to increase
reset delay to 180ms.
2. Add TOUCH_RPT_EN pin(GPP_A11) control to fix TOUCH_RPT_EN pin
keep high after system suspend.
BUG=b:181711141
TEST=Build and boot boten to OS.
Confirm TOUCH_RPT_EN pin keep low after system suspend.
Change-Id: I98efbe68dab538906802647582eba0e068d9c11f
Signed-off-by: Stanley Wu <stanley1.wu@lcfc.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51254
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Configure I2C bus 5 high and low time for p-sensor device.
BUG=b:181727056
TEST=Measured the I2C bus frequency reduce to 387 KHz.
Change-Id: I4b6d78d84b8ea145093f52bbb13684e2c6aa979c
Signed-off-by: Stanley Wu <stanley1.wu@lcfc.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51198
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Function is identical for all mainboards, so factor it out.
Change-Id: Ibe08fa7ae19bfc238d09158309f0a9fdb31ad21c
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50028
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Nearly every board that coreboot supports is a motherboard.
Change-Id: I1419874a0ba3f2e21568fa4b07b88f2048d10203
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50180
Reviewed-by: Jonathan Zhang <jonzhang@fb.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Suffix `SPIBAR_HWSEQ_XFER_TIMEOUT` with its units, use lowercase for hex
values and rename BIOS_CONTROL macros, as the register is not in SPIBAR.
Change-Id: I3bc1f5a5ebc4c562536829e63550c0b562b67874
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50752
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
UART pad configuration should not be done in common code, because that
may cause short circuits, when the user sets a wrong UART index.
Since all boards do pad setup on their own now, finally drop the pad
configuration from SoC common code.
Change-Id: Id03719eb8bd0414083148471ed05dea62a895126
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48829
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lance Zhao
|
|
UART pad configuration should not be done in common code, because that
may cause short circuits, when the user sets a wrong UART index. Thus,
add the corresponding pads to the early UART gpio table for the board as
a first step. Common UART pad config code then gets dropped in CB:48829.
Also switch to `bootblock_mainboard_early_init` to configure the pads in
early bootblock before console initialization, to make the console work
as early as possible. The board does not do any other gpio configuration
in bootblock, so this should not influence behaviour in a negative way
(e.g. breaking overrides).
Change-Id: I55815a824ea3a77e6e603ba4beb17457f37c48f5
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49433
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
This patch adds the changes to enable the TCSS.
BUG=b:175808146
TEST= Boot shadowmountain board, Test the functionality of the Type-C
ports on both the mainboard and daughterboard by plugging in the Type-C
devices and verified the devices are detected via EC console and in the
OS.
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Change-Id: Ieaf1170ca718a14d24b773a4a85516e0bbfbb569
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51026
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Since we have the SMN access block now, rename the SMU mailbox interface
registers to clarify that those are in the SMN register space.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ic5b7093f99eabd3c29610072b186ed156f335bd8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51400
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
The SMU mailbox interface gets accessed over the SMN register space, so
factor out those access functions into a separate common code SMN access
building block.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Iabac181972c02ae641da99f47b2aa9aa28dae333
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51399
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
P-sensor vendor fine-tune detect distance as 20mm for WWAN SAR table switch.
BUG=b:179000150
BRANCH=dedede
TEST=run "i2cdump -y -f 15 0x28" to confirm registers as expected.
un-approach：
=> register address: 0x01 value: 0x00
approach:
=> register address: 0x01 value: 0x02
Confirm WWAN SAR table work as expected.
Signed-off-by: Stanley Wu <stanley1.wu@lcfc.corp-partner.google.com>
Change-Id: I659721e60aa0766ed4c277dae43ded222e18ad1c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51343
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This mainboard uses a Comet Lake SoC and mixed-topology DDR4 memory.
Drop LPDDR-specific DQ and DQS mappings and comment about Cannon Lake.
Change-Id: Icb986d1c074e64b3cfad3897b69d35d108f64bff
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51336
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Crawford <tcrawford@system76.com>
Reviewed-by: Jeremy Soller <jeremy@system76.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
EFI_PEI_MP_SERVICES_STARTUP_ALL_APS passes in a boolean flag singlethread
which indicates whether the work should be scheduled in a serially on all APs
or in parallel. Current implementation of this function mp_startup_all_aps
always schedules work in parallel on all APs. This implementation ensures
mp_startup_all_aps honors to run serialized request.
BUG=b:169114674
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Change-Id: I4d85dd2ce9115f0186790c62c8dcc75f12412e92
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51085
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add a helper function mp_run_on_all_aps, it allows running a given
func on all APs excluding the BSP, with an added provision to run
func in serial manner per AP.
BUG=b:169114674
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Change-Id: I74ee8168eb6380e346590f2575350e0a6b73856e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51271
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Even though the implementation is different on Stoneyridge compared to
Picasso and Cezanne, the function prototypes are identical, so move them
to the AMD SoC common reset header file.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I8d3a3a9ea568ea18658c49612efabdbe36d5f957
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51395
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
BUG=b:182211161
TEST=builds
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: Ie3a3bb7526d734ae1936b8c4db43543b1174829d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51370
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mathew King <mathewk@chromium.org>
|
|
BUG=b:182211161
TEST=builds
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I554e7193494a4bbf005aaf2fb4efd6ded383fe07
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51369
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mathew King <mathewk@chromium.org>
|
|
BUG=b:182211161
TEST=builds
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: Ia03169c524dd12b8e7803ea8039c0e98a2b069e9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51368
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mathew King <mathewk@chromium.org>
|
|
BUG=b:182211161
TEST=builds
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I623fd052404a08cf0adb471bb654622960f1aa62
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51367
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mathew King <mathewk@chromium.org>
|
|
BUG=b:182211161
TEST=builds
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I45dcaa8b430721f864d4e5d78ae60883175085c3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51366
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mathew King <mathewk@chromium.org>
|
|
BUG=b:182211161
TEST=builds
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I7de5e4a4d2273d0ea5a84210ea0ce28d312eaa95
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51365
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mathew King <mathewk@chromium.org>
|
|
Convert the lines starts with whitespace with tab as applicable.
TEST=Built google/brya0 and ADLRVP with BUILD_TIMELESS=1: no changes.
Change-Id: Ibd11ad12caa1be866a851a8cd4bd23349e8ffbbe
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51375
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
According to Intel EmmitsBurg EDS, doc# 606161:
* Add PCI devid for SPI.
* Add PCI devid for ESPI (LPC).
EmmitsBurg (EBG) PCH is used in the chipset with Sapphire Rapids
Scalable Processor (SPR-SP).
Signed-off-by: Reddy Chagam <anjaneya.chagam@intel.com>
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Signed-off-by: Jonathan Zhang <jonzhang@fb.com>
Change-Id: Ie8925cb739c95c34febf9002149de437d19c8234
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51321
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
BUG=b:180529005
TEST=builds
Signed-off-by: Mathew King <mathewk@chromium.org>
Change-Id: I94d97a38d992f46b32c2c6aca4c8da688d3b76fc
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51257
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=b:180529005
TEST=boot majolica, all USB ports work
Signed-off-by: Mathew King <mathewk@chromium.org>
Change-Id: I6d3506bb4d54c7f8ea1e53576ef68d2aface6c89
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51256
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
BUG=b:181910592
TEST=builds
Signed-off-by: Mathew King <mathewk@chromium.org>
Change-Id: I7851d3b11ea3b026b999019d02df1144f8393753
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51270
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
|
|
BUG=b:180653357
TEST=builds
Signed-off-by: Mathew King <mathewk@chromium.org>
Change-Id: Ifd43d9cc1832d8ed8d90c68ba88b5667e3c04f89
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51269
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
BUG=b:180507937
TEST=builds
Signed-off-by: Mathew King <mathewk@chromium.org>
Change-Id: I7b8b2ab73d66e0aaa0e9b7570661c885f7f777ca
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51296
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=b:180529005
TEST=builds
Signed-off-by: Mathew King <mathewk@chromium.org>
Change-Id: I16de0869abd1eff4e89cf1b8128775858702acb3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51255
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Define the 26th bit of the fw_config for the regular touchpad
and numpad touchpad selection.
REGULAR_TOUCHPAD: 1
NUMPAD_TOUCHPAD: 0
BUG=b:174964012
BRANCH=zork
TEST=build pass
Signed-off-by: Kane Chen <kane_chen@pegatron.corp-partner.google.com>
Change-Id: Ie2055d6bb45a64bc0e59209cecc0f8a31c0f3718
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51278
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kangheui Won <khwon@chromium.org>
|
|
The VGA BIOS for AMD Padmelon and Google Zork are stored in `amd_blobs`.
Do not force inclusion of VGA BIOS when `USE_AMD_BLOBS` is not enabled.
Change-Id: I206e8fadc14ec0d9b162dc4d72813fdd3d43958b
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51341
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
This option defaults to n already.
Change-Id: I9f6407152f7cf2e2ac6fd1fff874e400f89a27ae
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51339
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
PSP_SHAREDMEM_BASE made the assumption that _psp_sharedmem_dram would
only match once. With CB:49332 there are now two symbols, and it was
grabbing the wrong one.
This change makes it so we match the exact symbol. It also switches to
using awk to simplify the code.
The bootblock.elf target that is added to the list of prerequisites also
creates the bootblock.map file that gets used to extract the base
address of the _psp_sharedmem_dram symbol.
BUG=b:181354692
TEST=Boot zork past bootblock
Fixes: 82d16b150ce3 ("memlayout: Store region sizes as separate symbols")
Suggested-by: Julius Werner <jwerner@chromium.org>
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I79675bd73f964282b54bca858830e26de64037c7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51300
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Some of the previous binaries were incorrect and should not be used
for Majolica because they are templates instead of APCBs specifically
built for the board. This APCB update also places the UMA region under
4G and size 32 MB which is essential for video output.
TEST=Boot with UEFI BIOS and verify we can get to OS. Also verify memory
region size, base and alignment.
Change-Id: Id797e2ad5bd67815c09752aedc19dad7dcf8ad12
Signed-off-by: Matt Papageorge <matthewpapa07@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51014
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Add ".data_hold_time_ns" to follow I2C specification.
The adjusted result aobut 0.315us(more than 0.3us)
BUG=b:181091107
BRANCH=zork
TEST=emerge-zork coreboot chromeos-bootimage
Signed-off-by: Kane Chen <kane_chen@pegatron.corp-partner.google.com>
Change-Id: Id92fadcb54b9722709e32ced1f0be001b8c97975
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51361
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Even though AMD does not need VBT we still need to implement the
vbt_get() function to not break the build with GOP driver enabled
(see fsps_return_value_handler() in fsp2_0/silicon_init.c
BUG=b:171234996
BRANCH=Zork
Change-Id: I80a5131a9852a05998b55b847243748d24cf535f
Signed-off-by: Nikolai Vyssotski <nikolai.vyssotski@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49865
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
BUG=b:182269526
TEST=builds
Signed-off-by: Mathew King <mathewk@chromium.org>
Change-Id: I351fb4fc493bb92b31e2c8bc946dfb048045335c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51384
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
BUG=b:182269526
TEST=builds
Signed-off-by: Mathew King <mathewk@chromium.org>
Change-Id: Ib33a46a6eead84eaff2c4ac320800b7993f5c3f6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51383
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
To define Mainboard Type config, use the fw_config bit[26].
Check MB Type to modify SDLE settings for different VCORE IC.
BUG=b:177193131
BRANCH=zork
Signed-off-by: John Su <john_su@compal.corp-partner.google.com>
Change-Id: If153c0a3e641ae32ef89737925bd9f62dfb71f3d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49683
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Kangheui Won <khwon@chromium.org>
|
|
Add the UPD updating hook in early stage for customization.
BUG=b:117719313
BRANCH=zork
TEST=build,check the hook function been executed.
Signed-off-by: Chris Wang <chris.wang@amd.corp-partner.google.com>
Change-Id: I4954a438a51b29b086015624127e651fd06f971b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51181
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=b:181766974
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I660f19d18810c35dafcd75bcd1993216b7b09644
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51268
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The headers added are generated as per FSP v2081_02.
Previous FSP version was v2037.
Changes Include:
- Adjust UPD Offset in FspmUpd.h and FspsUpd.h
- Add DevIntConfigPtr and NumOfDevIntConfig UPDs in Fsps.h
BUG=b:180758116
BRANCH=None
TEST=Build and boot ADLRVP
Cq-Depend: chrome-internal:3669105
Change-Id: Ib99748a428709ffad27d47f600e00bd91b70d8f3
Signed-off-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51248
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The current driver is using chip registers map to configure the SAR
sensor, which is opaque, especially when the datasheet is not published
widely.
Use more descriptive names, as defined in Linux kernel documentation at
https://www.kernel.org/doc/Documentation/devicetree/bindings/iio/proximity/semtech%2Csx9310.yaml
BUG=b:173341604
BRANCH=volteer
TEST=Dump all tables, check semtech property:
for i in $(find /sys/firmware/acpi/tables/ -type f) ; do
f=$(basename $i); cat $i > /tmp/$f.dat ; iasl -d /tmp/$f.dat
done
In SSDT.dsl, we have:
Package (0x06)
{
Package (0x02)
{
"semtech,cs0-ground",
Zero
},
Package (0x02)
{
"semtech,startup-sensor",
Zero
},
Package (0x02)
{
"semtech,proxraw-strength",
Zero
},
Package (0x02)
{
"semtech,avg-pos-strength",
0x0200
},
Package (0x02)
{
"semtech,combined-sensors",
Package (0x03)
{
Zero,
One,
0x02
}
},
Package (0x02)
{
"semtech,resolution",
"finest"
}
}
Change-Id: I8d1c81b56eaeef1dbb0f73c1d74c3a20e8b2fd7b
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50210
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ib317493fe938fe961aed06557e655ed8498e2694
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51382
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I388cdb1fb9b3decaa6eb6e0e4e538c620d3048a2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51381
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
There's no need to finalize the northbridge in SMM. This also makes
unification with Broadwell easier.
Tested on Asrock B85M Pro4, still boots and registers get locked.
Change-Id: I8b2c0d14a79e4fcd2e8985ce58542791cef9b1fe
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51157
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Add devicetree configuration parameters for mainboard-specific settings,
and provide reasonable defaults, which should usually be good enough.
This is based on Haswell SA Reference Code version 1.9.0 (Nov 2014).
Tested on Asrock B85M Pro4, registers now have the expected values.
Change-Id: I0dcdd4ca431c2ae1e62f2719c376d8bdef3054bd
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47223
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
When the SCI_EN bit is set, PM1 and GPE0 events will trigger a SCI
instead of a SMI#. However, SMI_STS bits PM1_STS and GPE0_STS can
still be set. Therefore, when SCI_EN is set, ignore PM1 and GPE0
events in the SMI# handler, as these events have triggered a SCI.
Do not ignore any other SMI# types, since they cannot cause a SCI.
Note that these bits are reserved on APL and GLK. However, SoC-specific
code already accounts for it. Thus, no special handling is needed here.
Change-Id: I5998b6bd61d796101786b57f9094cdaf0c3dfbaa
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50750
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Remove unused boot status settings.
Reset the power-off sequence to zero to meet hardware requirement.
BUG=b:179000151
BRANCH=none
TEST=boot asurada correctly
Signed-off-by: Hsin-Hsiung Wang <hsin-hsiung.wang@mediatek.com>
Change-Id: Ie9d39be532ec378bd6df6bf1b93307dae4068fc6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51246
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
We saw EXT_PMIC_EN1 and PPVAR_DVDD_PROC_BC power off sequence
failure, and after checking MT6315 MT6315 PMIC protection key
summary.xlsx and MT6315 Top and CLK programming guide.docx,
we found there are something wrong about the sequence of magic
key protection flow and clk setting. Update correct initial
flow.
BUG=b:179000151
BRANCH=none
TEST=boot asurada correctly
Signed-off-by: Hsin-Hsiung Wang <hsin-hsiung.wang@mediatek.com>
Change-Id: I1b7f970a44904fda09a97f4064eef7c95feefad7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51245
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The initial settings for MT6315 were not applied correctly
because the setup process didn't specify correct slave id
(incorrectly always sending 0), and may cause failure in
power off sequence.
BUG=b:179000151
BRANCH=none
TEST=boot asurada correctly
Signed-off-by: Hsin-Hsiung Wang <hsin-hsiung.wang@mediatek.com>
Change-Id: Ifd04da8ac55bcc9f9fdbc088d430522c2725ad47
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51056
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
|
|
BUG=b:180529005
TEST=builds
Signed-off-by: Mathew King <mathewk@chromium.org>
Change-Id: I836bb838cc97593451f869490ff3c9dd156245b8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51349
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=b:180507707
TEST=builds
Signed-off-by: Mathew King <mathewk@chromium.org>
Change-Id: I25ce0ca869ca854ff33242d2c416319e9688cc6f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51264
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=b:180507937
TEST=builds
Signed-off-by: Mathew King <mathewk@chromium.org>
Change-Id: I3cdd6422b1bc53ea934346327359cbc6d86baeeb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51043
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I674cff3352cd9f5d20b3d8f7e77339d045cadbb8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51357
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
