| Age | Commit message (Collapse) | Author |
|---|
|
It's no longer required.
Change-Id: I621226a3bdfba9bc8edfd6e511a5337ae603ae19
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2723
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
|
|
This wasn't previously spotted because the printk's were correct.
However if one needed to get the value of the BDSM or BGSM register
the value would reflect the other register's value.
Change-Id: Ieec7360a74a65292773b61e14da39fc7d8bfad46
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2689
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Currently the OS is free to use the memory located at the default
SMRAM space because it is not marked reserved in the e820. This can
lead to memory corruption on S3 resume because SMM setup doesn't save
this range before using it to relocate SMRAM.
Resulting tables:
coreboot memory table:
0. 0000000000000000-0000000000000fff: CONFIGURATION TABLES
1. 0000000000001000-000000000002ffff: RAM
2. 0000000000030000-000000000003ffff: RESERVED
3. 0000000000040000-000000000009ffff: RAM
4. 00000000000a0000-00000000000fffff: RESERVED
5. 0000000000100000-0000000000efffff: RAM
6. 0000000000f00000-0000000000ffffff: RESERVED
7. 0000000001000000-00000000acebffff: RAM
8. 00000000acec0000-00000000acffffff: CONFIGURATION TABLES
9. 00000000ad000000-00000000af9fffff: RESERVED
10. 00000000f0000000-00000000f3ffffff: RESERVED
11. 00000000fed10000-00000000fed19fff: RESERVED
12. 00000000fed84000-00000000fed84fff: RESERVED
13. 0000000100000000-000000018f5fffff: RAM
e820 map has 13 items:
0: 0000000000000000 - 0000000000030000 = 1 RAM
1: 0000000000030000 - 0000000000040000 = 2 RESERVED
2: 0000000000040000 - 000000000009f400 = 1 RAM
3: 000000000009f400 - 00000000000a0000 = 2 RESERVED
4: 00000000000f0000 - 0000000000100000 = 2 RESERVED
5: 0000000000100000 - 0000000000f00000 = 1 RAM
6: 0000000000f00000 - 0000000001000000 = 2 RESERVED
7: 0000000001000000 - 00000000acec0000 = 1 RAM
8: 00000000acec0000 - 00000000afa00000 = 2 RESERVED
9: 00000000f0000000 - 00000000f4000000 = 2 RESERVED
10: 00000000fed10000 - 00000000fed1a000 = 2 RESERVED
11: 00000000fed84000 - 00000000fed85000 = 2 RESERVED
12: 0000000100000000 - 000000018f600000 = 1 RAM
Booted and checked e820 as well as coreboot table information.
Change-Id: Ie4985c748b591bf8c0d6a2b59549b698c9ad6cfe
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2688
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
The previous code w.r.t. resource allocation was getting lucky
based on the way fixed mmio resources on the system were being
chosen. Namely, PCIEXBAR was the lowest mmio space and the other
fixed non-standar BARs were above it. The resource allocator would
then start allocating standard BARs below that.
On top of that other resources were being added when
dev_ops->set_resources() was being called on the PCI domain. At that
point the PCI range limit were already picked for where to start
allocating from.
To ensure we no longer get lucky during resource allocation add the
fixed resources in the host bridge and add the memory controller
cacheable memory areas. With those resources added the range limit
for standard PCI BARs is chosen properly.
Depending on haswell board configurations we may need to adjust and
pass in the size of physical address space needed for PCI resources
to the reference code. For the time being the CRBs appear to be OK.
Lastly, remove the SNB workaround for reserving 2MiB at 1GiB and 512MiB.
Output from 6GiB memory configuration:
MC MAP: TOM: 0x140000000
MC MAP: TOUUD: 0x18f600000
MC MAP: MESEG_BASE: 0x13f000000
MC MAP: MESEG_LIMIT: 0x7fff0fffff
MC MAP: REMAP_BASE: 0x13f000000
MC MAP: REMAP_LIMIT: 0x18f5fffff
MC MAP: TOLUD: 0xafa00000
MC MAP: BDSM: 0xada00000
MC MAP: BGSM: 0xad800000
MC MAP: TESGMB: 0xad000000
MC MAP: GGC: 0x209
coreboot memory table:
0. 0000000000000000-0000000000000fff: CONFIGURATION TABLES
1. 0000000000001000-000000000009ffff: RAM
2. 00000000000a0000-00000000000fffff: RESERVED
3. 0000000000100000-0000000000efffff: RAM
4. 0000000000f00000-0000000000ffffff: RESERVED
5. 0000000001000000-00000000acebffff: RAM
6. 00000000acec0000-00000000acffffff: CONFIGURATION TABLES
7. 00000000ad000000-00000000af9fffff: RESERVED
8. 00000000f0000000-00000000f3ffffff: RESERVED
9. 00000000fed10000-00000000fed17fff: RESERVED
10. 00000000fed18000-00000000fed18fff: RESERVED
11. 00000000fed19000-00000000fed19fff: RESERVED
12. 00000000fed84000-00000000fed84fff: RESERVED
13. 0000000100000000-000000018f5fffff: RAM
e820 map has 11 items:
0: 0000000000000000 - 000000000009fc00 = 1 RAM
1: 000000000009fc00 - 00000000000a0000 = 2 RESERVED
2: 00000000000f0000 - 0000000000100000 = 2 RESERVED
3: 0000000000100000 - 0000000000f00000 = 1 RAM
4: 0000000000f00000 - 0000000001000000 = 2 RESERVED
5: 0000000001000000 - 00000000acec0000 = 1 RAM
6: 00000000acec0000 - 00000000afa00000 = 2 RESERVED
7: 00000000f0000000 - 00000000f4000000 = 2 RESERVED
8: 00000000fed10000 - 00000000fed1a000 = 2 RESERVED
9: 00000000fed84000 - 00000000fed85000 = 2 RESERVED
10: 0000000100000000 - 000000018f600000 = 1 RAM
Output from 4GiB memory configuration:
MC MAP: TOM: 0x100000000
MC MAP: TOUUD: 0x14f600000
MC MAP: MESEG_BASE: 0xff000000
MC MAP: MESEG_LIMIT: 0x7fff0fffff
MC MAP: REMAP_BASE: 0x100000000
MC MAP: REMAP_LIMIT: 0x14f5fffff
MC MAP: TOLUD: 0xafa00000
MC MAP: BDSM: 0xada00000
MC MAP: BGSM: 0xad800000
MC MAP: TESGMB: 0xad000000
MC MAP: GGC: 0x209
coreboot memory table:
0. 0000000000000000-0000000000000fff: CONFIGURATION TABLES
1. 0000000000001000-000000000009ffff: RAM
2. 00000000000a0000-00000000000fffff: RESERVED
3. 0000000000100000-0000000000efffff: RAM
4. 0000000000f00000-0000000000ffffff: RESERVED
5. 0000000001000000-00000000acebffff: RAM
6. 00000000acec0000-00000000acffffff: CONFIGURATION TABLES
7. 00000000ad000000-00000000af9fffff: RESERVED
8. 00000000f0000000-00000000f3ffffff: RESERVED
9. 00000000fed10000-00000000fed17fff: RESERVED
10. 00000000fed18000-00000000fed18fff: RESERVED
11. 00000000fed19000-00000000fed19fff: RESERVED
12. 00000000fed84000-00000000fed84fff: RESERVED
13. 0000000100000000-000000014f5fffff: RAM
e820 map has 11 items:
0: 0000000000000000 - 000000000009fc00 = 1 RAM
1: 000000000009fc00 - 00000000000a0000 = 2 RESERVED
2: 00000000000f0000 - 0000000000100000 = 2 RESERVED
3: 0000000000100000 - 0000000000f00000 = 1 RAM
4: 0000000000f00000 - 0000000001000000 = 2 RESERVED
5: 0000000001000000 - 00000000acec0000 = 1 RAM
6: 00000000acec0000 - 00000000afa00000 = 2 RESERVED
7: 00000000f0000000 - 00000000f4000000 = 2 RESERVED
8: 00000000fed10000 - 00000000fed1a000 = 2 RESERVED
9: 00000000fed84000 - 00000000fed85000 = 2 RESERVED
10: 0000000100000000 - 000000014f600000 = 1 RAM
Output from 2GiB memory configuration:
MC MAP: TOM: 0x40000000
MC MAP: TOUUD: 0x100600000
MC MAP: MESEG_BASE: 0x3f000000
MC MAP: MESEG_LIMIT: 0x7fff0fffff
MC MAP: REMAP_BASE: 0x100000000
MC MAP: REMAP_LIMIT: 0x1005fffff
MC MAP: TOLUD: 0x3ea00000
MC MAP: BDSM: 0x3ca00000
MC MAP: BGSM: 0x3c800000
MC MAP: TESGMB: 0x3c000000
MC MAP: GGC: 0x209
coreboot memory table:
0. 0000000000000000-0000000000000fff: CONFIGURATION TABLES
1. 0000000000001000-000000000009ffff: RAM
2. 00000000000a0000-00000000000fffff: RESERVED
3. 0000000000100000-0000000000efffff: RAM
4. 0000000000f00000-0000000000ffffff: RESERVED
5. 0000000001000000-000000003bebffff: RAM
6. 000000003bec0000-000000003bffffff: CONFIGURATION TABLES
7. 000000003c000000-000000003e9fffff: RESERVED
8. 00000000f0000000-00000000f3ffffff: RESERVED
9. 00000000fed10000-00000000fed17fff: RESERVED
10. 00000000fed18000-00000000fed18fff: RESERVED
11. 00000000fed19000-00000000fed19fff: RESERVED
12. 00000000fed84000-00000000fed84fff: RESERVED
13. 0000000100000000-00000001005fffff: RAM
e820 map has 11 items:
0: 0000000000000000 - 000000000009fc00 = 1 RAM
1: 000000000009fc00 - 00000000000a0000 = 2 RESERVED
2: 00000000000f0000 - 0000000000100000 = 2 RESERVED
3: 0000000000100000 - 0000000000f00000 = 1 RAM
4: 0000000000f00000 - 0000000001000000 = 2 RESERVED
5: 0000000001000000 - 000000003bec0000 = 1 RAM
6: 000000003bec0000 - 000000003ea00000 = 2 RESERVED
7: 00000000f0000000 - 00000000f4000000 = 2 RESERVED
8: 00000000fed10000 - 00000000fed1a000 = 2 RESERVED
9: 00000000fed84000 - 00000000fed85000 = 2 RESERVED
10: 0000000100000000 - 0000000100600000 = 1 RAM
Verified through debug messages that range limits as well as
resources were being properly honored.
Change-Id: I2faa7d8a2a34a6a411a2885afb3b5c3fa1ad9c23
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2687
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
|
|
This commit updates the Lynx Point resource reservations before
the coreboot allocator assigns resources. There is no need to mark
anything as subtractive decode because there are no devices/buses
linked to the LPC device.
The I/O range reservations consists of claiming the first 4KiB
of I/O space. The PMBASE, GPIOBASE, and LPC generic I/O decode
ranges are checked against the default claimed range. If those
ranges overlap or fall outside of the default range then those
resources are added.
The MMIO range reservations consist of claiming everything from
the I/O APIC to 4GiB. The RCBA and the LPC Generic Memory range
register are then conditionally added if they fall outside of
the default MMIO range.
Change-Id: I0f560a03814a2b15961fdbe61e4164cd54cff7a5
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2682
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
- Add ME device ID for Lynxpoint LP
- Add GPU device IDs for ULT
- SATA init tweaks from checking against DXE reference code
- Remove the ICH7 from the SPI driver so it works on all lynxpoint
without having to add more LPC device ID checks
- Add function disable for audio dsp and xhci, remove PCI bridge
- Add interrupt route registers for new devices (needs romstage setup)
Change-Id: Idb48f50d0bacb6bf90531c3834542b9abb54fb8a
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/2680
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
The current code is attempting to convert from an invalid
starting temperature. Since we aren't sure where the temperature
will come from yet just return a static value.
This stops the kernel from going to S5 on boot because it
thinks the temperature is too high.
Change-Id: I433fa407e545458344af5842b353df5bc71bfdad
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/2679
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
This option is not required for haswell. Enabling the option doesn't
do anything aside from complicate mtrr calculation. Therefore, remove
it.
Change-Id: I897523ff7d3606eb89961674c2eb3d384e584857
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2678
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
There are 2 issues in lb_cleanup_memory_ranges(). The first
is that during sort there is a neighbor comparison that initially
starts with the current entry. The second issue is that merging
has an off by one comparison for adjacent entries.
Before:
coreboot memory table:
0. 0000000000000000-0000000000000fff: CONFIGURATION TABLES
1. 0000000000001000-000000000009ffff: RAM
2. 00000000000a0000-00000000000fffff: RESERVED
3. 0000000000100000-0000000000efffff: RAM
4. 0000000000f00000-0000000000ffffff: RESERVED
5. 0000000001000000-00000000acebffff: RAM
6. 00000000acec0000-00000000acffffff: CONFIGURATION TABLES
7. 00000000ad000000-00000000af9fffff: RESERVED
8. 00000000f0000000-00000000f3ffffff: RESERVED
9. 00000000fed10000-00000000fed17fff: RESERVED
10. 00000000fed18000-00000000fed18fff: RESERVED
11. 00000000fed19000-00000000fed19fff: RESERVED
12. 00000000fed84000-00000000fed84fff: RESERVED
13. 0000000100000000-000000018f5fffff: RAM
After:
coreboot memory table:
0. 0000000000000000-0000000000000fff: CONFIGURATION TABLES
1. 0000000000001000-000000000009ffff: RAM
2. 00000000000a0000-00000000000fffff: RESERVED
3. 0000000000100000-0000000000efffff: RAM
4. 0000000000f00000-0000000000ffffff: RESERVED
5. 0000000001000000-00000000acebffff: RAM
6. 00000000acec0000-00000000acffffff: CONFIGURATION TABLES
7. 00000000ad000000-00000000af9fffff: RESERVED
8. 00000000f0000000-00000000f3ffffff: RESERVED
9. 00000000fed10000-00000000fed19fff: RESERVED
10. 00000000fed84000-00000000fed84fff: RESERVED
11. 0000000100000000-000000018f5fffff: RAM
Change-Id: I656aab61b0ed4711c9dceaedb81c290d040ffdec
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2671
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
This commit adds support for the deveveloper, recovery,
and write protect querying. It just uses jumpers on the
Basking Ridge board.
Noted ability to togggle jumpers results in toggling the
respective modes.
Change-Id: Iac189a1fa0245654591e2e9075380db422a329a0
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2676
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
|
|
While looking at the Basking Ridge schematic I noticed some changes
and wanted to make sure they were reflected in the GPIO map.
Change-Id: I686653c164314ae9f68c42331d2f950751411d4a
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2675
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
|
|
Needed to map VGA OPROM IDs to actual device IDs
Change-Id: I6743905c3db52519bf18f4bcc1a972aec43d3e9d
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2674
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
|
|
The baskingridge has a non-zero alt_gp_smi_en value in the
devicetree.cb file. It has just to be determined which GPI
pins should trigger an SMI on basking ridge. Without this change
the board would hang during boot (presumably through a SMI flood).
No more hangs once the value is zero.
Change-Id: I9704071bb7966bd3d0bbbc4aafede3f42d829b17
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2673
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
The Grays Reef CRB is deprecated by order of Intel. Basking Ridge
is the new hotness. Therefore, rename graysreef to basking ridge.
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Change-Id: I203497e165d8efc99d3438c4c548140a6e9cc649
Reviewed-on: http://review.coreboot.org/2672
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
|
|
- Add device IDs for lynxpoint mobile and LP variants.
- Update the clock gating setup based on BWG
- Update the SATA programming based on BWG
- Add a DEVSLP0 mux config register
Change-Id: Icf4d7bab7f3df7adef5eb7c5e310a6995227a0e5
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/2649
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
|
|
The low power variant of the chipset introduces a completely
new interface to the GPIOs.
This is a 1KB region and so needs to be moved as well so it does
not conflict with other IO regions.
Also expose the gpio_get functions to ramstage and move the
prototypes to pch.h so they can be used for both GPIO interfaces.
Change-Id: I20bc18669525af16de8cdf99f0ccfa9612be63ad
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/2648
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
|
|
This adds microcode ffff000a and the CPUIDs for ULT.
Change-Id: I341c1148a355d8373b31032b9f209232bd03230a
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/2647
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
|
|
Device IDs for northbridge and GPU.
Also mask off the lock bit in the memory map registers.
Change-Id: I9a4955d4541b938285712e82dd0b1696fa272b63
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/2646
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
|
|
There are enough subtle differences that it is useful to have
a Kconfig entry to differentiate the ULT/LP chipet from the
desktop/mobile versions.
Change-Id: I04ca1bc6f90bcf9e6994ea7125c98347e8def898
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/2645
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
|
|
This commit contains a bevy of updates:
- PCI device id is updated to match Lynx Point EDS in the ME driver.
- Allocate the memory to store the consumption of the MBP.
- me_bios_payload structure is now a structure of pointers that point
into the allocated memory.
- The ICC profile structure was updated to correctly reflect the
documentation.
Verfied that output of MBP reading can handle unknown items.
Change-Id: I43cc45e6b797444c105e7c842eb5684e9c104687
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2641
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
According to the 0.8.0 ME BWG this is a new state. It's not very clear
what exactly it entails, but the Basking Ridge CRB was tripping it when
MRC_DEBUG was enabled (presumably because of a DID timeout).
Instead of 0x17 one can now see the proper message for this state.
Change-Id: I5bda1de7d3d957d38a4760a02dcd170ec48782e9
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2640
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Some of the Lynx Point ids were off. Correct those and make
the pei data BAR fields consistent with the others.
Change-Id: I4102439588362cdb94643bd1ce69c9fa4278329e
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2622
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
The CS5536 companion device has three different power domains.
* working domain
* standby domain
* RTC domain
When the system is "off" only the standby domain is powered.
MFGPT[7:6] are member of the standby power domain.
MFGPT7 is used to control the backlight of the device and so the
timer gets used and configured during system boot. If the system
does a reboot the timer stays configured and the Linux driver
can not use it:
"ot200-backlight: ot200-backlight.0: MFGPT 7 not availale"
The cs5535-mfgpt has a function to hard-reset all MFGPTs but the
system hangs after the first access to a MFGPT register - cause
unknown.
/*
* This is a sledgehammer that resets all MFGPT timers. This is required by
* some broken BIOSes which leave the system in an unstable state
* (TinyBIOS 0.98, for example; fixed in 0.99). It's uncertain as to
* whether or not this secret MSR can be used to release individual timers.
* Jordan tells me that he and Mitch once played w/ it, but it's unclear
* what the results of that were (and they experienced some instability).
*/
static void reset_all_timers(void)
{
uint32_t val, dummy;
/* The following undocumented bit resets the MFGPT timers */
val = 0xFF; dummy = 0;
wrmsr(MSR_MFGPT_SETUP, val, dummy);
}
After playing around with this undocumented MSR it looks like I only
need to set bit 7 to free the MFGPT7.
BTW, all MFGPT[0:5] will be reset during pll_reset().
Change-Id: I54a8d479ce495b0fc2f54db766a8d793bbb5d704
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Reviewed-on: http://review.coreboot.org/2527
Tested-by: build bot (Jenkins)
Reviewed-by: Jens Rottmann <JRottmann@LiPPERTembedded.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
|
|
This is no longer tied to a GPIO but has a proper chipset pin.
Change-Id: Iba70338e8c67e3c3c1cb32e69bfea1282fda8cb5
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/2643
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Now that MMCONF_SUPPORT_DEFAULT is enabled by default remove
the pcie explicit accesses. The default config accesses use
MMIO.
Change-Id: I8406cec16c1ee1bc205b657a0c90beb2252df061
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2618
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
The register that controls global reset is named the Power
Mangement Initialization Regiser (PMIR). Update the defines
to reflect the documentation.
Additionally, there is no core well reset control according to the
EDS. There is, however, a CF9 lock field to lock this register down.
Change-Id: I773c33bec63a06cdb869eb9f94553d476e492798
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2619
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
The ME9 requirements have added some registers and changed some
of the MBP state machine. Implement the changes found so far in
the ME9 BWG. There were a couple of reigster renames, but the
majority of th churn in the me.h header file is just introducing
the data structures in the same order as the ME9 BWG.
Change-Id: I51b0bb6620eff4979674ea99992ddab65a8abc18
Signed-Off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2620
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
The IA32_ENERGY_PERFORMANCE_BIAS MSR can only be read or written
to if the CPU supports it. The support is indicated by ECX[3] for
cpuid(6). Without this guard, some Haswell parts would GP# fault
in this routine.
No more GP# while running on haswell CRBs.
Change-Id: If41e1e133e5faebb3ed578cba60743ce7e1c196f
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2639
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
|
|
In order for coreboot to assign resources properly the pci
drivers need to have th proper device ids. Add the host controller
and the LPC device ids for Lynx Point.
Resource assignment works correctly now w/o odd behavior because
of conflicts.
Change-Id: Id33b3676616fb0c428d84e5fe5c6b8a7cc5fbb62
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2638
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
|
|
The reference code sends the dram init done command to the ME.
Therefore, there is no need for coreboot to do this.
Change-Id: I6837d6c50bbb7db991f9d21fc9cdba76252c1b7b
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2633
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Even though this is under the graysreef board it really
applies to the Basking Ridge board. A subsequent patch will
rename graysreef to baskingridge.
The GPIO pins were updated to reflect the Basking Ridge schematics
as well as the DIMM spd addresses and USB over current pins.
Change-Id: Ice4e05f5203de3024cd463dfccf0bcfec1e247c1
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2632
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Add a FIXME about checking a MCHBAR register that isn't setup yet.
Also, remove revision updating because I can't find anything in the
docs that suggest this is required for haswell.
Change-Id: Ia8a6e08f82e18789e31c6c2ec2c1d63740c18dc4
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2631
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
The intel-framework code has an updated pei_data structure.
Use the new structure and revision. Also, remove the scrambler
seed saving in CMOS since that appears to be handled in the saved
data from the reference code.
Change-Id: Ie09a0a00646ab040e8ceff922048981d055d5cd2
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2630
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Change the hard coded values in udelay.c to use the #defines
for MSRs and BCLK.
Change-Id: I2bbeb0b478d2e3ca155e8f82006df86c29a4f018
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2629
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Grays Reef is one of Intel's CRBs for the Haswell processor. The
platform is named Shark Bay.
GPIOs were the main focus so IRQ routing and ACPI still needs to be
further looked at.
Change-Id: Ie94b7af66f772714992a92612c76ca93b9b27088
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2621
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Boot haswell ULT and see LPT reported properly.
Change-Id: I48344a8dde6adbbf331c91231342de45b1b6c32a
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/2697
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
This is the steps outlined in the BWG.
It seems this is a lot simpler now (so far) which is good.
To test, boot to chromeos with 3.7 kernel + i915.preliminary_hw_support=1 and
see that the i915 driver complains a lot less than before and that a
splashscreen is displayed.
Change-Id: I722c90ecd351860949cedab24533f6c10e5b90e5
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/2696
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
This follows the new method outlined in the LPT BWG.
It is also very pedantic about its operation so it
is easier to read and compare against the docs and
the reference code implementation.
Change-Id: I235d634cded0c75ec0e9f53488f5b366107a18fa
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/2694
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Add support for SMM modules by leveraging the RMODULE lib. This allows
for easier dynamic SMM handler placement. The SMM module support
consists of a common stub which puts the executing CPU into protected
mode and calls into a pre-defined handler. This stub can then be used
for SMM relocation as well as the real SMM handler. For the relocation
one can call back into coreboot ramstage code to perform relocation in
C code.
The handler is essentially a copy of smihandler.c, but it drops the TSEG
differences. It also doesn't rely on the SMM revision as the cpu code
should know what processor it is supported.
Ideally the CONFIG_SMM_TSEG option could be removed once the existing
users of that option transitioned away from tseg_relocate() and
smi_get_tseg_base().
The generic SMI callbacks are now not marked as weak in the
declaration so that there aren't unlinked references. The handler
has default implementations of the generic SMI callbacks which are
marked as weak. If an external compilation module has a strong symbol
the linker will use that instead of the link one.
Additionally, the parameters to the generic callbacks are dropped as
they don't seem to be used directly. The SMM runtime can provide the
necessary support if needed.
Change-Id: I1e2fed71a40b2eb03197697d29e9c4b246e3b25e
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2693
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Change-Id: Ib406b9d5005243d79eea5d2c0c6c86b5aa949891
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2721
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Add a bootblock.c file for the northbridge and setup the
PCIEXBAR as the first thing using IO PCI config acceses.
After that all PCI config accesses can use MMIO.
Change-Id: I51d229c626c45705dda1757c2f14265cbc0e6183
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2617
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
The Haswell parts use a PCH code named Lynx Point (Series 8). Therefore,
the southbridge support is included as well. The basis for this code is
the Sandybridge code. Management Engine, IRQ routing, and ACPI still requires
more attention, but this is a good starting point.
This code partially gets up through the romstage just before training
memory on a Haswell reference board.
Change-Id: If572d6c21ca051b486b82a924ca0ffe05c4d0ad4
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2616
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
The original code attempted to reserve a space in RAM for coreboot to
remain resident. This turns out not to be needed, and breaks things
for the kernel since the exynos5250-smdk5250 kernel device tree starts
RAM at 0x40000000.
(This patch was originally by Gabe, I'm just uploading it)
Change-Id: I4536edaf8785d81a3ea008216a2d57549ce5edfb
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2698
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
|
|
Change the OSC method to actually grant control of
PCIe capabilities to the OS instead of granting no
control. I believe the logic was backwards in the
original commit. Bits should be set when granting
control and cleared when not granting control. By
setting the return value to 0x00, we effectively
tell the OS that it cannot control any PCIe
capability. See section 6.2.9 of the ACPI spec
version 3.0 for more information.
This edit is a duplication of the OSC method that
is in the src/southbridge/intel/bd82x6x/pch.asl
file.
Change-Id: Id2462ab12203afceb9033f24d06b4dfbf2236d2e
Signed-off-by: Mike Loptien <mike.loptien@se-eng.com>
Reviewed-on: http://review.coreboot.org/2714
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
This enables branch prediction. We can probably find a better place
to do this, but for now we'll do it in snow's romstage main().
Change-Id: I86c7b6bc9e897a7a432c490fb96a126e81b8ce72
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2701
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Since commit »Drop redundant CHIP_NAME in mainboard.c« (a93c3fe7) [1]
`CHIP_NAME` is unneeded for mainboards as the name is composed
automatically in `src/devices/root_device.c` from the strings in
Kconfig.
Unfortunately the ports for Google Butterfly, Link and Parrot as
as well as IEI PM-LX2-800-R10 introduced CHIP_NAME again. So drop
it again too.
[1] http://review.coreboot.org/1635
Change-Id: Ice7577a2a5c6070e196f2647c440b7a8e140e27e
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2708
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
PS_HOLD gets set in exynos' power_init().
Change-Id: Ib08e0afcad23cbd07dc7e3727fd958a1bc868b5a
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2700
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Call the power_init() function. We appear to have forgotten about it
when deprecating lowlevel_init_subsystems(), but it didn't seem to
cause problems until we got to doing more interesting stuff recently.
There are some clean-ups to do from the original code, such as not
attempting to configure I2C from PMIC code, which we'll get around
to in follow-up patches.
(Credit to Gabe for spotting this)
Change-Id: I6a59379e9323277d0b61469de9abe6d651ac5bfb
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2699
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
The current default is IDE mode which is slower compared to AHCI
mode. Therefore use AHCI mode by default.
A similar change was made for AMD Persimmon in commit
»Enable SATA AHCI for faster boot with SeaBIOS.« (96be74c7) [1]
but was indirectly reverted by »sb800: Add sata ahci/raid mode
kconfig option« (d4a0e7d0) [2].
[1] http://review.coreboot.org/220
[2] http://review.coreboot.org/225
Change-Id: I4fa31b0a3280891e7a3f37675ae8415205818947
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2661
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
|
|
There's a compile time error that we didn't catch since the
board defaults as used by the build bot won't expose it.
Just make watchdog_off() a no-op statement so there aren't any
stray semicolons in the preprocessor output.
Change-Id: Ib5595e7e8aa91ca54bc8ca30a39b72875c961464
Reported-by: 'lautriv' on irc.freenode.net/#coreboot
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/2627
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
We used to allow mainboards to override subsystems using
mainboard_pci_subsystem_vendor_id and mainboard_pci_subsystem_device_id.
Mechanisms have changed and the only occurrence of these names is in
the header.
Change-Id: Ic2ab13201a2740c98868fdf580140b7758b62263
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/2625
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
|
|
Despite everywhere the model name M5A88-V is used, in Kconfig the
string M5A88PM-V is used. Searching for that model string on the
WWW does not return anything which is unrelated to coreboot, so
change that string to M5A88-V.
Change-Id: I25cf9d4a5fc3f9b9356e8616452066ebf873f44c
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2613
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-by: QingPei Wang <wangqingpei@gmail.com>
|
|
Add PEI updates and ACPI updates for supporting EHCI to XHCI
USB port support.
Change-Id: I9ace68a1b3950771aefb96c1319b8899291edd9a
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-on: http://review.coreboot.org/2519
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
|
|
Adding the 'WordBusNumber' macro to the PCI0
CRES ResourceTemplate in the Persimmon DSDT.
This sets up the bus number for the PCI0 device
and the secondary bus number in the CRS method.
This change came in response to a 'dmesg' error
which states:
'[FIRMWARE BUG]: ACPI: no secondary bus range in _CRS'
By adding the 'WordBusNumber' macro, ACPI can set
up a valid range for the PCIe downstream busses,
thereby relieving the Linux kernel from "guessing"
the valid range based off _BBN or assuming [0-0xFF].
The Linux kernel code that checks this bus range is
in `drivers/acpi/pci_root.c`. PCI busses can have
up to 256 secondary busses connected to them via
a PCI-PCI bridge. However, these busses do not
have to be sequentially numbered, so leaving out a
section of the range (eg. allowing [0-0x7F]) will
unnecessarily restrict the downstream busses.
This change will apply to other AMD mainboards and
will be in a different commit.
Change-Id: I44f22bc03a0dcbcd2594d4291508826cc2146860
Signed-off-by: Mike Loptien <mike.loptien@se-eng.com>
Reviewed-on: http://review.coreboot.org/2592
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
|
|
This eliminates the use of do_div() in favor of using libgcc
functions.
This was tested by building and booting on Google Snow (ARMv7)
and Qemu (x86). printk()s which use division in vtxprintf() look good.
Change-Id: Icad001d84a3c05bfbf77098f3d644816280b4a4d
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2606
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Changes:
- Get rid of the inagua mainboard specific code and use the
platform generic function wrapper that was added in change
http://review.coreboot.org/#/c/2497/
AMD f14: Add SPD read functions to wrapper code
- Move DIMM addresses into devicetree.cb
- Add the ASF init that used to be in the SPD read code into
mainboard_enable()
Notes:
- The DIMM reads only happen in romstage, so the function is not
available in ramstage. Point the read-SPD callback to a generic
function in ramstage.
Change-Id: Id05227fcf18c6ab94ffe1beb50b533ab7b0535db
Signed-off-by: Kimarie Hoot <kimarie.hoot@se-eng.com>
Reviewed-on: http://review.coreboot.org/2607
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Currently for Advansus A785E-I, ASRock E350M1 and ASUS M5A88-V
despite what is chosen in Kconfig »Chipset« menu item,
$ more .config
[…]
# CONFIG_ENABLE_IDE_COMBINED_MODE is not set
CONFIG_IDE_COMBINED_MODE=0x1
# CONFIG_SB800_SATA_IDE is not set
CONFIG_SB800_SATA_AHCI=y
# CONFIG_SB800_SATA_RAID is not set
CONFIG_SB800_SATA_MODE=0x2
[…]
the SATA controller is put into IDE mode.
$ lspci -nn | grep SATA
00:11.0 SATA controller [0106]: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 SATA Controller [IDE mode] [1002:4390] (rev 40)
Commit »sb800: Add sata ahci/raid mode kconfig option«
(d4a0e7d0) [1] added the options above to configure the mode
using Kconfig and some SB800 boards were adapted already. For
example commit »persimmon: sb800 sata mode configure update«
(1386fa74) [2] did so for AMD Persimmon.
Doing the same by assigning the Kconfig variable to the value in
`platform_cfg.h` integrates this with the three remaining boards
listed above.
The patch is successfully tested with the ASRock E350M1.
$ lspci -nn | grep SATA
00:11.0 SATA controller [0106]: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 SATA Controller [AHCI mode] [1002:4391] (rev 40)
[1] http://review.coreboot.org/225
[2] http://review.coreboot.org/227
Change-Id: I227257e2c8f04f18c27ff00fe62d42e372de67e4
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2610
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
|
|
Replace »persimmon« by »board« in comment to keep `diff` output
between boards small.
Change-Id: Ieae2a63782c488ae35f22eb30f5b1049200d12c8
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2611
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
|
|
Changes:
- Get rid of the union_station mainboard specific code and
use the platform generic function wrapper that was added
in change http://review.coreboot.org/#/c/2497/
AMD f14: Add SPD read functions to wrapper code
- Move DIMM addresses into devicetree.cb
- Add the ASF init that used to be in the SPD read code into
mainboard_enable()
Notes:
- The DIMM reads only happen in romstage, so the function is not
available in ramstage. Point the read-SPD callback to a generic
function in ramstage.
Change-Id: I19d6b0d674b67294519383f80928471b37da1e14
Signed-off-by: Kimarie Hoot <kimarie.hoot@se-eng.com>
Reviewed-on: http://review.coreboot.org/2609
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Changes:
- Get rid of the south_station mainboard specific code and
use the platform generic function wrapper that was added
in change http://review.coreboot.org/#/c/2497/
AMD f14: Add SPD read functions to wrapper code
- Move DIMM addresses into devicetree.cb
- Add the ASF init that used to be in the SPD read code into
mainboard_enable()
Notes:
- The DIMM reads only happen in romstage, so the function is not
available in ramstage. Point the read-SPD callback to a generic
function in ramstage.
Change-Id: If4291d25ea81bf375f55b64c07c223a847a211d0
Signed-off-by: Kimarie Hoot <kimarie.hoot@se-eng.com>
Reviewed-on: http://review.coreboot.org/2608
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
This is previously used exception code from libpayload.
On startup it installs and then tests an exception handler.
The test is an unaligned memory operation.
Yes, we've seen what might be exceptions in the ramstage, and
it makes sense to handle them. This code is identical in structure
and operation to the previously committed payload exception handler,
though we reserve the right to change it as circumstances require.
The remaining question is whether we need it in romstage.
Change-Id: I24484686c33c9757af8ba171ebae9773828fb69d
Signed-off-by: Gabe Black <gabeblack@google.com>
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/2614
Tested-by: build bot (Jenkins)
Reviewed-by: David Hendricks <dhendrix@chromium.org>
|
|
AGESA code has wrong definition of CR0_PE bit (1 instead of 0).
PE [Protected Mode Enable] is 0 bit in CR0 register
(If PE=1, system is in protected mode, else system is in real mode)
Bit 1 is MP [Monitor co-processor]
(Controls interaction of WAIT/FWAIT instructions with TS flag in CR0)
System uses CR0_PE define, but I didn't expect any consequences because of this bug.
Change-Id: I54d9a8c0ee3af0a2e0267777036f227a9e05f3e1
Signed-off-by: Konstantin Aladyshev <aladyshev@nicevt.ru>
Reviewed-on: http://review.coreboot.org/2591
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
|
|
According to BKDG:
"Memory controller (MCT) and DRAM controllers (DCTs) additions:
• Support for 933 MHz (1866 MT/s) MEMCLK frequency."
Change-Id: I6f307ce3fcb355d5445f1ea86def73a41b928a57
Signed-off-by: Konstantin Aladyshev <aladyshev@nicevt.ru>
Reviewed-on: http://review.coreboot.org/2589
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
|
|
_RDMSR instruction loads the contents of a 64-bit model specific register (MSR)
specified in the ECX register into registers EDX:EAX.
The EDX register is loaded with the high-order 32 bits of the MSR
and the EAX register is loaded with the low-order 32 bits.
EDX:EAX = MSR[ECX]
So bit 49 will be contained in EDX register.
Buggy code instead of bit 49 (CombineCr0Cd) sets bit [49-32=17] (PfcStrideDis).
PfcStrideDis bit disables stride prefetch generation. This leads to memory
bandwidth loss.
_________
Supermicro H8QGI board
After applying this change i observed huge memory bandwidth increase in tests
that runs on small amount of cores. But unfortunately it doesn't affect
overall bandwidth results on 4P system with 48 cores.
So i think that in this system leading limiting factor is
AMD HT-ASSIST feature (Probe filter).
But right now it is not working. System stucks in Linux boot. I have done
some experiments and figured out that stuck happens when system have cores in
compute unit (CU) other than CU with BSC (boot strap core).
CU is two cores (primary and seconary) that shares some things (L2 cache, FPU ...)
So with probe filter i can boot Linux with one (BSC)
or two (BSC + secondary core in its CU) cores.
And with this configuration i can see memory bandwidth on 1 core (or two cores)
close to original bios.
Change-Id: I5a95f5b753d600c70d3c93d36fecc687610c61cd
Signed-off-by: Konstantin Aladyshev <aladyshev@nicevt.ru>
Reviewed-on: http://review.coreboot.org/2588
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
|
|
The Hudson-E1's default SPI speed for normal i.e. non-fast reads is 66 MHz,
but the SST 25VF032B datasheet allows max. 25. Lower the speed to 22 MHz,
otherwise BIOS flashing fails.
Change-Id: I22e87d833a3ebd316b6e873595a2480831533ab1
Signed-off-by: Jens Rottmann <JRottmann@LiPPERTembedded.de>
Reviewed-on: http://review.coreboot.org/2605
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Changes:
- Get rid of the persimmon mainboard specific code which has been
moved into the wrapper as a platform generic function in change
http://review.coreboot.org/#/c/2497/
AMD f14: Add SPD read functions to wrapper code
- Move DIMM addresses into devicetree.cb
- Add the ASF init that used to be in the SPD read code into
mainboard_enable()
Notes:
- The DIMM reads only happen in romstage, so the function is not
available in ramstage. Point the read-SPD callback to a generic
function in ramstage.
Change-Id: I5f017dbb8dee5a09ec19734a6069ff9b71a6ab50
Signed-off-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-on: http://review.coreboot.org/2500
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-by: Jens Rottmann <JRottmann@LiPPERTembedded.de>
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
|
|
Change:
This is the initial step for moving the AMD F14 & HUDSON1,2,3
SPD-read callout out of the mainboard directories and into
the wrapper. The next step is to update the platforms to use
this routine in BiosCallouts.c and to delete the code from the
mainboard directories. The DIMM addresses should be moved into
devicetree.cb.
If there are significant differences or reasons that the mainboard
needs to override this code, it's perfectly reasonable to keep using
the version in the mainboard, but this allows us to remove duplicated
code and simplify the mainboard directories.
Notes:
This started by duplicating what was in Persimmon, and was changed to
use the devicetree.cb structures. The ASF setup was also removed from
the persimmon copy (PMIO writes to 0x28 & 0x29) as that's not needed
for the SPD access and doesn't make sense to initialize here.
Significant cleanup and magic number reduction was done as well.
It is intended that this file will not be included in ramstage as
the DIMM init is all done in romstage.
This is similar to what was done for Parmer/Thatcher in commit
7fb692bd - http://review.coreboot.org/#/c/2190/
Fam15tn: Move SPD read from mainboards into wrapper
Yes, it would make sense to split this into two separate files
and move the SMBUS initialization and access into the southbridge
wrapper. Maybe that can come next.
Change-Id: I1e106d3912c160b0015bf02158d9faba4f578ee3
Signed-off-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-on: http://review.coreboot.org/2497
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-by: Jens Rottmann <JRottmann@LiPPERTembedded.de>
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
|
|
I've used an operating system for over 10 years now that makes
UTF-8 easy. It's not called Linux or OSX.
When UTF-8 is needed, of course, then we can look again.
I can't think of a single redeeming feature of placing
it in the comment in this manner. It's certainy not
needed.
The inclusion of UTF-8 characters is inconvenient,
especially from a text terminal.
I don't really want to start using compose in
CROSH shell terminals on chromeos.
We might want to incorporate "no UTF-8" as a
commit filter. For now, get rid of these
characters.
Change-Id: If94cc657bae1dbd282bec8de6c5309b1f8da5659
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/2604
Reviewed-by: Bernhard Urban <lewurm@gmail.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
This reverts commit 1cd616082100f47dc2d6d73669c6aa2e5eb039ad
Division bites us again. I don't know how or why, but printk() seems to break (again) with this patch. I'm surprised we didn't encounter problems earlier on...
Change-Id: I81cb9f20879f5eb73a76e1af47b96a68d1e81dc8
TODO: Find a better solution for div64. This one is too painful, but seems necessary for now (and sort-of works with our vtxprintf hack).
Reviewed-on: http://review.coreboot.org/2600
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
This adds some real GPIO mappings where virtual GPIOs were used before.
Change-Id: I25d4be45f986c8d622b97151f8bdae2651baf3e6
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2603
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
This adds an enum for GPIO ports on the Exynos5. To make them
useful, they are assigned the absolute MMIO address where a
s5p_gpio_bank struct can point to.
Change-Id: Ia539ba52d7393501d434ba8fecde01da37b0d8aa
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2602
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
cosmetics
Change-Id: Iea33768d901641861aa7b2c76af8753a848f584d
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2601
Tested-by: build bot (Jenkins)
Reviewed-by: David Hendricks <dhendrix@chromium.org>
|
|
While reading through the file fix some spotted errors like
indentation, locution(?), capitalization and missing full stops.
Change-Id: Id435b4750e329b06a9b36c1df2c39d2038a09b18
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2484
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
|
|
A board without HAVE_ACPI_RESUME did not build with
COLLECT_TIMESTAMPS enabled as `cbmem.c` was not built.
Change-Id: I9c8b575d445ac566a2ec533d73080bcccc3dfbca
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/2549
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
|
|
This is required to enable EARLY_CBMEM_INIT.
Change-Id: I6d8caf382aa48eded81c1e94bbbcd3975ea88a1a
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/2550
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Models 6ex and 6fx select UDELAY_LAPIC so cannot select
contradicting UDELAY_TSC here.
Model 1067x requires speedstep.
Change-Id: I69d3ec8085912dfbe5fe31c81fa0a437228fa48f
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/2525
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Quoting Jens Rottmann [1]:
Nevertheless I still think this whole function is bogus for the E350M1. The
function assumes GPIO21 is wired to reset APU PCIe lane 0+1 (PCIe x8, port 4+5
as Coreboot/AGESA calls it), GPIO25 resets lane 2 (PCIe x4) and GPIO02 lane 3.
But the E350M1 has PCIe x16 i.e. probably APU lanes 0-3 bundled, completely
different layout. They could have chosen GPIO21 to force resets, or 25 - or
maybe 50 like on the Persimmon or any other they fancied or - and this is the
most probable - none at all. Having BiosGnbPcieSlotReset() toggle some GPIOs
without knowing what they do on the E350M1 (if anything at all) is nonsense.
In my opinion this whole function should just "return AGESA_UNSUPPORTED" and
good riddance.
[1] http://review.coreboot.org/#/c/2445/
Change-Id: Iac66da41182e838c7e6925250cc3982adbb3e4ec
Reported-by: Jens Rottmann <JRottmann@LiPPERTembedded.de>
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2489
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-by: Jens Rottmann <JRottmann@LiPPERTembedded.de>
|
|
These are essential functions for setting up the display port and
framebuffer, and also enable such things as aux channel
communications. We do some very simple initialization in romstage,
mainly set a GPIO so that the graphics is powering up, but the complex
parts are done in the ramstage. This mirrors the way in which graphics
is done in the x86 size.
I've added a first pass at a real device, and put it in the mainboard
Kconfig, hoping for corrections. Because startup is so complex,
depending on device type, I've created a 'displayport' device that
removes some of the complexity and makes the flow *much* clearer. You
can actually follow the flow by looking at the code, which is not true
on other implementations. Since display port is perhaps the main port
used on these chips, that's a reasonable compromise. All parameters of
importance are now in the device tree.
Change-Id: I56400ec9016ecb8716ec5a5dae41fdfbfff4817a
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/2570
Tested-by: build bot (Jenkins)
|
|
Since the merg of the ASRock E350M1 port (a649a96e) the compiler
warns about the following [1].
mainboard.c:35, GNU Compiler 4 (gcc), Priorität: Normal
no previous prototype for 'set_pcie_reset' [-Wmissing-prototypes]
mainboard.c:43, GNU Compiler 4 (gcc), Priorität: Normal
no previous prototype for 'set_pcie_dereset' [-Wmissing-prototypes]
Adding the function prototypes to the beginning of the file as
done in commit »Persimmon updates for AMD F14 rev C0« (d7a696d0)
addresses the warning.
[1] http://qa.coreboot.org/job/coreboot-gerrit/4975/warnings13Result/package.-139448264/file.-1544928473/
[2] http://review.coreboot.org/137
Change-Id: Iad2e62ec37c3a2f749a264974b61ac7c226e9b83
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2590
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Set up the clocks used for sound and turn on the sound clock.
Change-Id: Ic59bfa9ae87116299503e6d25aeefba98c842fb8
Signed-off-by: Gabe Black <gabeblack@google.com>
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/2587
Tested-by: build bot (Jenkins)
Reviewed-by: David Hendricks <dhendrix@chromium.org>
|
|
The MMC0 on google/snow can run in 8 bit mode. To simplify driver development,
we thought disabling it (using zero, which runs in 1-bit / 4-bit mode) may help.
However, after some experiments in payload drivers, setting pinmux to 8 bit mode
can still allow MMC to run in 1-bit / 4-bit mode, so it's pretty safe to enable
8 bit mode by default for better performance.
Verified to boot on google/snow, and got MMC0 working.
Change-Id: Ic0acc723fe6a8aecf373429d3801beadd70815d9
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/2585
Tested-by: build bot (Jenkins)
Reviewed-by: David Hendricks <dhendrix@chromium.org>
|
|
The power up default for the 14M_25M_48M_OSC switchable clock output ball of
the SB800 chipset is 14 MHz. sb800/bootblock.c changes this to 48 MHz,
which is the correct value for almost all SIOs. However, not for
'smscsuperio' (SMSC SCH311x), which needs the original 14 MHz and is not
configurable for other clock speeds. A wrong SIO clock supply results in
funny RS232 output (wrong bit speed) and non-working PS/2.
We could switch back to 14 MHz in the mainboard's romstage.c, but then the
clock frequency would change twice. The resulting short 48 MHz burst causes
a handful of rubbish characters on RS232 on every boot until the SIO clock
has stabilized again.
This patch skips the SB800 clock switch if the SIO Kconfig requests 14 MHz.
This does not affect any boards currently in the repository (yet).
Change-Id: Icff41fd88dc41c08f3700ab4f786852f04eff2a4
Signed-off-by: Jens Rottmann <JRottmann@LiPPERTembedded.de>
Reviewed-on: http://review.coreboot.org/2454
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
|
|
The first reason for selecting the CPU model at compile time was a
multi-second pause if booting a single core Fusion T40R with MAX_CPUS=2.
Recent tests show the pause has disappeared, someone must have fixed it.
The second reason was me not knowing how to make a single vgabios image
work with two different PCI IDs. Many thanks to Martin Roth for educating
me! Quote:
"The way to make coreboot use the same vbios for different video device IDs
is through the map_oprom_vendev function. In family 14 it's in
northbridge/amd/agesa/family14/amdfam14_conf.c You would name your video
bios 1002,9802 in the config and all the other device/vendor IDs for the
family 14h processors will fall through the initial check for the video
bios and will get remapped to use that vbios. This only works if you're
initializing the vbios inside coreboot. I don't know if you're using
SeaBios as a payload, but if you are you can add the vbios to cbfs as
vgaroms/vbios.rom and the rom will always be initialized."
I'd like to add the vgabios is added as type 'optionrom' when Coreboot make
adds it, however to work with SeaBios it has to be added manually with
cbfstool and with type 'raw', or it will hang.
Change-Id: I8190d0c3202a60dfccb77dde232f9ba7ce5ce318
Signed-off-by: Jens Rottmann <JRottmann@LiPPERTembedded.de>
Reviewed-on: http://review.coreboot.org/2584
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
OK, this is tl;dr. But I need to write this in hopes we make
sure we don't put code like this into coreboot. Ever.
Our excuse in this case is that it was imported, not obviously wrong,
and easily changed. It made sense to get it in, make it work, then
do a cleanup pass, because changing everything up front is almost
impossible to debug.
The exynos code has bunch of base register values, e.g.
These are base addresses of things that look like a memory-mapped
struct. To get these to a pointer, they created the following macro,
which creates an inline function.
static inline unsigned int samsung_get_base_##device(void) \
{ \
return cpu_is_exynos5() ? EXYNOS5_##base : 0; \
}
And then invoke it 31 times in a .h file, e.g.:
SAMSUNG_BASE(clock, CLOCK_BASE)
to create 31 functions.
And then use it:
struct exynos5_clock *clk =
(struct exynos5_clock *)samsung_get_base_clock();
OK, what's wrong with this? It's easier to ask what's right with it. Answer: nothing.
I have a long list of what's wrong, and I may leave some things out,
but here goes:
1. the "function" can return a NULL if we're not on exynos5. Most uses of the code
don't check the return value.
2. And why would this function be running, if we're not on an exynos5? Why compile it in?
3. Note the cast everywhere a samsung_get_base_xxx is used.
The function returns an untyped variable, requiring the *user* to get two
things right: the cast, and the function invocation. One can replace that _clock(); with
_power(); in the code above, and they will be referencing the wrong registers, and
they'll never get an error!
We have a C compiler; use it to type data.
4. You're generating 31 functions using cpp each and every time the file is included.
The C compiler has to parse these each time. It's not at all like a simple cpp
macro which is only generated on use.
5. You can't tags or etags this code
6. In fact, any kind of analysis tool will be unable to do anything with this cpp magic.
That's only a partial list.
So what's the right way to do it? Just make typed constants, viz:
Or, since I expect people will want the lower case function syntax, I've left
it that way:
Now we've got something that is efficient, and we don't even need to protect with
any more.
Hence this change. We've got something that is type checked, does not require users to
cast on each use, will catch simple programming errors, can be analyzed with standard tools,
and builds faster.
So if we make a mistake:
struct exynos5_clock *clk =
samsung_get_base_adc();
We'll see it:
src/cpu/samsung/exynos5250/clock.c: In function 'get_pll_clk':
src/cpu/samsung/exynos5250/clock.c:183:3: error: initialization from incompatible pointer type [-Werror]
which we would not have seen before.
As a minor benefit, it shaves most of a second off the compilation.
Change-Id: Ie67bc4bc038a8dd1837b977d07332d7d7fd6be1f
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/2582
Tested-by: build bot (Jenkins)
|
|
Update coreboot to use SeaBIOS' tag rel-1.7.2.1
Change-Id: I01969407964a7cf64f7c4800b59c6aed845b24f9
Signed-off-by: Idwer Vollering <vidwer@gmail.com>
Reviewed-on: http://review.coreboot.org/2575
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Commit f154c018
Author: Marc Jones <marcj303@gmail.com>
Date: Wed Dec 14 11:24:00 2011 -0700
Persimmon audio codec verb patch.
Reviewed-on: http://review.coreboot.org/490
has a typo code*c* in the comments for `AZALIA_OEM_VERB_TABLE`. As
this was copied over to the LiPPERT Fam14 boards, use the following
command to fix the typo.
$ git grep -l cocec | xargs sed -i s,cocec,codec,
Change-Id: I1525b0445edab81ab136b3adece52b78ba7abc71
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2576
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
|
|
Looking at the coreboot log
[…]
PCI: 00:12.0 [1002/4397] enabled
sb800_enable() PCI: Static device PCI: 00:12.1 not found, disabling it.
sb800_enable() PCI: 00:12.2 [1002/4396] ops
PCI: 00:12.2 [1002/4396] enabled
sb800_enable() PCI: 00:13.0 [1002/4397] ops
PCI: 00:13.0 [1002/4397] enabled
sb800_enable() PCI: Static device PCI: 00:13.1 not found, disabling it.
sb800_enable() PCI: 00:13.2 [1002/4396] ops
PCI: 00:13.2 [1002/4396] enabled
[…]
and the `lspci -tnvv` output running the proprietary vendor BIOS
attached to the Wiki page of the ASRock E350M1 [1][2]
-[0000:00]-+-00.0 1022:1510
+-01.0 1002:9802
+-01.1 1002:1314
+-04.0-[01]--
+-11.0 1002:4391
+-12.0 1002:4397
+-12.2 1002:4396
+-13.0 1002:4397
+-13.2 1002:4396
[…]
both PCI devices do not exist, so remove them from `devicetree.cb`.
Commit 48918f7 [3]
Persimmon, Inagua: PCI devs 12.1, 13.1 (USB) don't exist, but 14.6 (GEC) does
did the same for AMD Inagua and AMD Persimmon.
[1] http://www.coreboot.org/ASRock_E350M1
[2] http://www.coreboot.org/File:ASRock_E350M1_info_dump.tar.bz2
[3] http://review.coreboot.org/2463
Change-Id: Ief6de1bda093d1f29d5925985e5c3839cdded537
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2536
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
|
|
If you try to reset the system with outb(3,0x92), outb(4,0xcf9) or a
triple-fault it will instead crash with a messy screen. As the more common
outb(0xFE, 0x64) doesn't work with our setup, Linux will crash whenever you
ask it to reboot. Closer inspection shows that on a warm boot of Coreboot
agesawrapper_amdinitpost() always fails with error code 7. Looks like DDR3
re-init goes wrong somehow. I tried find the reason for this but was
unable to. I am convinced this is not board specific but a bug in AGESA.
In the end I had to settle for a workaround: if amdinitpost returns 7 this
patch resets the system harder with outb(0x06, 0x0cf9), after that RAM init
will succeed. As amdinitpost is early in POST this automatic reset is
quick enough not to be noticable.
I'd perfer a real fix, but that's all I have.
Change-Id: I4763254b489f42a135232e45328ecf0d5c4d961a
Signed-off-by: Jens Rottmann <JRottmann@LiPPERTembedded.de>
Reviewed-on: http://review.coreboot.org/2573
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Step 2: change the Persimmon code to adapt it to the new board's hardware.
The Toucan-AF is a COM Express Compact Type 6 form factor embedded board:
- AMD Fusion G-T56N (1.65 GHz dual core) or T40R (1 GHz single core) APU
- 1-4 GB DDR3 memory down
- 1x VGA, 2x DisplayPort (1 switchable to LVDS)
- AMD A55E (Hudson-E1) southbridge
- 8x USB 2.0
- 4x SATA
- HD Audio (with codec on baseboard)
- NEC uPD78F0532 microcontroller on I2C ("SEMA")
- 7x PCIe2.0 x1 (1 on PEG)
- Intel I210 GbE (on APU PCIe x1, can be disabled for additional PCIe)
- 2x SST 25VF032B (SO8, soldered) 4 MB SPI flash (BIOS and failsafe BIOS)
The Toucan-AF has no SIO on board. This patch includes basic support for a
Winbond W83627DHG (PS/2, 2x RS232), because the ADLINK ExpressBase-6 used
for evaluation happens to have one. The code may have to be adapted to the
actual baseboard of the application.
http://www.adlinktech.com/PD/web/PD_detail.php?pid=1132
Change-Id: I9041b905bad45852ac9b402fcbd5decbc98b377b
Signed-off-by: Jens Rottmann <JRottmann@LiPPERTembedded.de>
Reviewed-on: http://review.coreboot.org/2572
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Step 1: copy all files unmodified from Persimmon. This makes it much
easier later to see how the two boards actually and deliberately differ
when porting bugfixes from one to the other. Git's copy detection is
imperfect (and slow).
Change-Id: I1ff02913479c07679f8c3ae5e6dd7876e6000b55
Signed-off-by: Jens Rottmann <JRottmann@LiPPERTembedded.de>
Reviewed-on: http://review.coreboot.org/2571
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Step 2: change the Persimmon code to adapt it to the new board's hardware.
The FrontRunner-AF is a PC/104+ form factor embedded board:
- AMD Fusion G-T56N (1.65 GHz dual core) or T40R (1 GHz single core) APU
- DDR3 SO-DIMM socket (1.5 or 1.35V)
- VGA and LVDS (via Analogix ANX3110)
- AMD A55E (Hudson-E1) southbridge
- 6x USB 2.0
- 1x SATA, 1x CFast socket
- HD Audio (via Realtek ALC886)
- PCI and ISA (via ITE IT8888)
- NEC uPD78F0532 microcontroller on I2C ("SEMA")
- Intel I210 GbE (on APU PCIe x1)
- SMSC SCH3112 SIO
- PS/2
- 2x RS232/485
- 2x SST 25VF032B (SO8, soldered) 4 MB SPI flash (BIOS and failsafe BIOS)
http://www.adlinktech.com/PD/web/PD_detail.php?pid=1131
Change-Id: Id55f89d224ad669b351c36128b12299802b721ba
Signed-off-by: Jens Rottmann <JRottmann@LiPPERTembedded.de>
Reviewed-on: http://review.coreboot.org/2553
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Step 1: copy all files unmodified from Persimmon. This makes it much
easier later to see how the two boards actually and deliberately differ
when porting bugfixes from one to the other. Git's copy detection is
imperfect (and slow).
Change-Id: I2fd1bf8428fc8a1e7becee888b6182b9bd8166a0
Signed-off-by: Jens Rottmann <JRottmann@LiPPERTembedded.de>
Reviewed-on: http://review.coreboot.org/2552
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
In the file `COPYING` in the coreboot repository and upstream [1]
just one space is used.
The following command was used to convert all files.
$ git grep -l 'MA 02' | xargs sed -i 's/MA 02/MA 02/'
[1] http://www.gnu.org/licenses/gpl-2.0.txt
Change-Id: Ic956dab2820a9e2ccb7841cab66966ba168f305f
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2490
Tested-by: build bot (Jenkins)
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
|
|
The SD/MMC interface on Exynos 5250 must be first configured with, GPIO, and
pinmux settings before it can be detected and used in ramstage / payload.
Verified on armv7/snow and successfully boot into ramstage.
Change-Id: I26669eaaa212ab51ca72e8b7712970639a24e5c5
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: http://review.coreboot.org/2561
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
This breaks booting, and in fact stages.c is always going to be special: for it to work it has to be compiled for arm only, no thumb allowed. It's probably better to leave the stages.o target in explicitly so it's clear that it has to be compiled with a particular set of flags, rather than try to remember that we must always have the default rules no break stages.c compilation. That would be a mess. I will be pushing a CL to get rid of the assembly dump, but will be a trivial fix.
This reverts commit 8f4647a24bf19a96531af9905b23ae8a2fc2675a
Change-Id: I5e3d8e5b991f6ccf4d49078378cd4615fb230ca0
Reviewed-on: http://review.coreboot.org/2554
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
This allows to drop some special cases in romstage.c
Change-Id: I53fdfcd1bb6ec21a5280afa07a40e3f0cba11c5d
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2551
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
It's not used, and not needed.
Change-Id: Ifca92f3606ac58fc26e09676488c3add5d84ae79
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2548
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Change-Id: I0069ec26278b82d61ce5bcfb94d77647dfd3254b
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/2530
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
This is a leftover from when we were debugging
this code. Let's make it easier to understand.
Change-Id: Ia3d0ab1504ff9dd9634d5f393d3c59fe1e43a0c0
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2543
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
It's been on for all boards per default since several years now
and the old code path probably doesn't even work anymore. Let's
just have one consistent way of doing things.
Change-Id: I58da7fe9b89a648d9a7165d37e0e35c88c06ac7e
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2547
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
