Age | Commit message (Collapse) | Author |
|
The general rule is to configure GPIOs used by coreboot in bootblock
(using the reset table), and GPIOs used by OS in RAM stage.
However, GPIO_9 will be used as both, and we need to reconfigure it to
properly set up debounce, however, it is no longer possible to change
bootblock, so we also configure it in RAM stage to make the new
debounce configuration take affect.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
BUG=b:113880780
BRANCH=none
TEST=Reboot stress test grunt (>100 times); no messages in dmesg like:
tpm tpm0: Timeout waiting for TPM ready
Change-Id: I0f1bca176ed3f9cebf6b9e9e1008905e492a2f03
Reviewed-on: https://review.coreboot.org/c/30922
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
FT4 has a strange property where whenever the debounce registers for any
one gpio are changed, the FT4 disables interrupt propagation for ALL
gpio irqs for ~4ms.
In other words, if an edge interrupt of one gpio happens exactly during
this debounce-irq-off window immediately following the configuration of
another gpio, the interrupt will be lost.
It is quite difficult to deal with this in the kernel, since during kernel
boot time, drivers & devices are probed asynchronously, meaning it may
happen that an already loaded driver may miss an interrupt when some
later driver is being probed and configuring its gpio interrupt.
To eliminate this possibility, we pre-configure the debounce registers in
ram stage for all gpios that will be used as irqs later by the kernel
using the same configuration as used by the kernel, as per this table:
IRQ Debounce
Edge Remove Glitch
Level High Preserve Low Glitch
Level Low Preserve High Glitch
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
BUG=b:113880780
BRANCH=none
TEST=Reboot stress test grunt (>100 times); no messages in dmesg like:
tpm tpm0: Timeout waiting for TPM ready
Change-Id: I94c7ecfb14e5bb209b3598e10287c80eb19da25b
Reviewed-on: https://review.coreboot.org/c/30921
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Thes are already defined identically ~20 lines above.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
BUG=none
BRANCH=none
TEST=compile
Change-Id: Ic3faeb97788b2b524345cdbfb368e98d43bac075
Reviewed-on: https://review.coreboot.org/c/30920
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
define wakeup-delay-ms to 20ms. This avoids the pop
noise heard at the start of capture.
BUG=b:119926436
TEST=with kernel patch
https://lore.kernel.org/patchwork/patch/1029806/
no pop sound heard at start of capture
Change-Id: I299a584ef2ba66d1e752515100cbe3919b2108f6
Signed-off-by: Akshu Agrawal <akshu.agrawal@amd.com>
Reviewed-on: https://review.coreboot.org/c/30726
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
define wakeup-delay-ms to 20ms. This avoids the pop
noise heard at the start of capture.
BUG=b:119926436
TEST=with kernel patch
https://lore.kernel.org/patchwork/patch/1029806/
no pop sound heard at start of capture
Change-Id: I2593afa69cfb955f6a2b695406855e0f31f28468
Signed-off-by: Akshu Agrawal <akshu.agrawal@amd.com>
Reviewed-on: https://review.coreboot.org/c/30725
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Passes out wakeup-delay to driver. This delay is applied at
the start of capture to make sure dmics are ready before we
start recording. This avoids pop noise at begining of capture.
BUG=b:119926436
TEST=
With kernel patch
https://lore.kernel.org/patchwork/patch/1029806/
No pop sound heard at start of capture
Change-Id: I32b18bf80fad5899ab4093a127dfd52d589bc365
Signed-off-by: Akshu Agrawal <akshu.agrawal@amd.com>
Reviewed-on: https://review.coreboot.org/c/30724
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Change-Id: If179687f0a15cf5b16723ad18d8eb86a2d5fa48d
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/c/29479
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Declaring a Kconfig symbol ahead to override its default also always
sets implicit dependencies. If the original symbol doesn't have any,
Kconfig gets confused.
Change-Id: Ie6d9ca96e4b6037eefd432dd386cb5e540deb0ed
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/30925
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Libgfxinit provides a better alternative to the native C init. While
libgfxinit mandates an ada compiler, we want to encourage use of it
since it is in much better shape and is actually maintained.
This way libgfxinit also gets build-tested by Jenkins.
Change-Id: Ic6678d3455f1116e7e67a67b465a79df020b2399
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/27532
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
After a96e66a (soc/intel: Clean mess around UART_DEBUG) got merged,
all mainboard using intel cannonlake,coffeelake, kabylake, skylake,
icelake and whiskeylake get affected.
Using INTEL_LPSS_UART_FOR_CONSOLE instead of UART_DEBUG
and set default console for each platform.
TEST=Intel client and IoT team has verified that LPSS uart
is working fine on CNL, WHL and ICL RVPs.
Change-Id: I0381a6616f03c74c98f837e3c008459fefd4818c
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/30913
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Whiskeylake processor have an internal device called Camarillo
dedicated for thermal management support, turn it on so processor
thermal driver can be loaded.
BUG=N/A
TEST=Boot up and run lspci on Sarien board, Bus 0 Device 4 Funcion 0
can be seen.
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: I937960fde2704cddb1fe0058ab622f4b5de401d7
Reviewed-on: https://review.coreboot.org/c/30858
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
PC Engines apu1 has a 20 pin LPC header that allows connection of
external TPM module.
Add necessary Kconfig option and devicetree entry for TPM.
Change-Id: Ic9f3d41c6e8346a12553386b9c00de6b8fd21abd
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Reviewed-on: https://review.coreboot.org/c/30354
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Remove double nesting of chip northbridge/amd.
There is requirement to keep SPD address map in
the same chip block with device 0:18.2.
Change-Id: Id3a161c54341d0c5c569ea6118ee6f890b7f62e6
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/30735
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Remove double nesting of chip northbridge/amd.
There is requirement to keep SPD address map in
the same chip block with device 0:18.2.
Change-Id: I67fcb59a63046865f660e628a61c2944b0f89a74
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/30734
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: mikeb mikeb <mikebdp2@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Remove double nesting of chip northbridge/amd.
There is requirement to keep SPD address map in
the same chip block with device 0:18.2.
Change-Id: Ib212f24c3d697a009d2ca8e2c77220de4bfb7573
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/30733
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
conf pointer could be null, access it only if its not null.
Foundby=klocwork
BUG=N/A
TEST=N/A
Signed-off-by: Pratik Prajapati <pratikkumar.v.prajapati@intel.com>
Change-Id: I0611e15d52edd8e69e4234b8ac602f35efba4015
Reviewed-on: https://review.coreboot.org/c/30862
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
|
|
conf pointer could be null, access it only if its not null.
Foundby=klocwork
BUG=N/A
TEST=N/A
Signed-off-by: Pratik Prajapati <pratikkumar.v.prajapati@intel.com>
Change-Id: I1b3d6f53d2bfd9845ad7def91c4e6ca92651d216
Reviewed-on: https://review.coreboot.org/c/30860
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
|
|
Add processor power limits control support to configure values.
BRANCH=None
BUG=b:122343940
TEST=Built and tested on Arcada system
Change-Id: I5990dc05b51481a0074855914cef20cf07378cde
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/30907
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Set PL1 and PL2 values to 25W and 51W respectively for
processor power limits control.
BRANCH=None
BUG=b:122343940
TEST=Built and tested on Arcada system
Change-Id: I4098f334ed5cb6c4a6f35f1a7b12809f34c23fa3
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/30908
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Signed-off-by: Praveen hodagatta pranesh <praveenx.hodagatta.pranesh@intel.com>
Change-Id: I519ed4b5b403622d6bb01ad0bdd04e01dedff7d8
Reviewed-on: https://review.coreboot.org/c/30794
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
The RVP11 is a dual-channel DDR4 SO-DIMM on skylake H platform.
This patch add following chages
- Add overridetree.cb for RVP11
- Select skylake PCH-H chipset config for RVP11.
- Add GPIO table as per board schematics.
- Add audio verb table for RVP11.
- Set the UserBd UPD to BOARD_TYPE_DESKTOP.
BUG=None
TEST= Build and flash, confirm boot into yocto OS on KBL RVP11
platform. verified PCI, USB, ethernet, SATA, display,
audio and power functionalities.
Signed-off-by: Praveen hodagatta pranesh <praveenx.hodagatta.pranesh@intel.com>
Change-Id: Id86f56df06795601cc9d7830766e54396d218e00
Reviewed-on: https://review.coreboot.org/c/29809
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Does not fix 3rdparty/, *.S or *.ld or yet.
Change-Id: I66b48013dd89540b35ab219d2b64bc13f5f19cda
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/17656
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Add a new Kconfig NO_BOOTBLOCK_CONSOLE to disable the BOOTBLOCK_CONSOLE
option completely. The commit message of fbb11cf (ARM: Separate the
early console (romstage) from the bootblock console.) states that it
doesn't work before romstage on Exynos 5420.
Change-Id: I9b56a52f2555b5233300f27031a9ef50e7ab7cea
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/30926
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
This mainboard uses SOC internal UART 1 instead of UART 2 like all other
mc_apl1 mainboards.
Change-Id: Ib986962ed068fee019ffcec0391d43d5ab178458
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/30933
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Accoding to desciption in FSP header, Vref Configuration will be set to
2 if VREF_CA to CH_A and VREF_DQ_B to CH_B.
BUG=N/A
TEST=Build and boot up on Arcada platform.
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: I02e16e141b81d766a6060ca08283f432abd96647
Reviewed-on: https://review.coreboot.org/c/30280
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Required for ACPI S3 suspend support at some motherboards.
Synchronizing with flashchips.c/h flashrom source code.
Signed-off-by: Mike Banon <mikebdp2@gmail.com>
Change-Id: I69809fb638f59f0b399f3a1615f5d8d2b2ddae45
Reviewed-on: https://review.coreboot.org/c/30928
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Required for ACPI S3 suspend support at some motherboards.
Synchronizing with flashchips.c/h flashrom source code.
Signed-off-by: Mike Banon <mikebdp2@gmail.com>
Change-Id: Idc63665937ab1bfdf15c4054001daa288bfdd47b
Reviewed-on: https://review.coreboot.org/c/30927
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Enable at24 EEPROM by adding ASL of nvm
BUG=b:122583978
BRANCH=master
TEST=Build and run for basic camera functions
Change-Id: Ifc2060c2ceb7d1a8ef490f36f484deb425a37c95
Signed-off-by: Chen, JasonX Z <jasonx.z.chen@intel.com>
Reviewed-on: https://review.coreboot.org/c/30795
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
|
|
Change-Id: I41ad1ce06d9afcc99941affa232fa76ffa6631fb
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/27531
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Pineview CPUs support a non-eviction mode that ought to be used
during cache as ram setup.
This assumes that all atoms that need to set a special register to
enable L2 cache are socketed and hence uses a static Kconfig option
to set that MSR on affected CPUs.
Tested on Foxconn D41S, still boots.
Change-Id: Iec943f5710314fb7a644d89dbd6d8c425f4ed735
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/30863
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Based on previous reverse-engineering done on "util/superiotool".
TEST=NOT TESTED (yet)
Change-Id: I6c433fa04c01ba6315bcdca699030dfce18a169a
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/28971
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Only tested on APL.
Change-Id: I53f680fc4342a9bd1cd0ba9d72e025995e25f7f2
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/c/29902
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
|
|
* Route IO 0x6e/0x6f to LPC bus
* Setup ITE8526 in early_mainboard_romstage_entry
* Fix romstage serial console by disabling internal uart default setting
* Unselect CONFIG_INTEGRATED_UART, as it doesn't use internal UARTs
* Select CONFIG_DRIVERS_UART_8250IO, as it has a SuperIO serial
* Configure UPDs related to serial
Change-Id: I59cd83ed43dbf4ee26685e4a573de153291f7074
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/30827
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Default to FSP binary and headers shiped in 3rdparty/fsp.
* Drop headers and code from vendorcode/intel/fsp1_0/broadwell_de
* Select HAVE_FSP_BIN to build test the platform
* Fetch FSP repo as submodule
* Make FSP_HEADER_PATH known from FSP2.0 useable on FSP1.0
* Introduce FSP_SRC_PATH for FSP source file
* Add sane defaults for FSP_FILE
Tested on wedge100s.
Change-Id: I46f201218d19cf34c43a04f57458f474d8c3340d
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/30742
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Jay Talbott <JayTalbott@sysproconsulting.com>
|
|
It was only hooked up for galileo board when using the obsolete
FSP1.1. I don't see how it can be useful...
Change-Id: Ifd7cbd664cfa3b729a11c885134fd9b5de62a96c
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/30691
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Static values, copy paste from multi-node fam15 code.
Add header that shall have declarations of functions
common to different families factored out.
Change-Id: I07bc046c74280f49e46793c119d36b87b8789949
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/30732
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Static values, copy paste from multi-node fam15 code.
Add header that shall have declarations of functions
common to different families factored out.
Change-Id: I2401acb9269674bac054fa9a6dd60ca8a21b36a9
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/30731
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Pointless to declare static struct in a header.
Change-Id: I757f6346017681e32900f67b25fb5700a68d86b8
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/30900
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
I refused bolton under agesa/ once it turned out to be
blobbed. We have AMD_PI_BOLTON.
Change-Id: Ic3cb9ada2d4f14b49f6ad54c58e6b950a1732b70
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/30899
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
This reverts commit 4e3cd744492c7a3d80bca55a35276efeada731e5.
Reason for revert: Daisuke says "We'll keep EFS on Kalista/Karma enabled"
Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org>
Change-Id: I2f11ffc9dd7eb05a2560261bbf472e8488c274d9
Reviewed-on: https://review.coreboot.org/c/30857
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
These were left out by mistake while rebasing, when
AGESA/binaryPI directory split happened.
Change-Id: Id0cb07e9ad7edede60cd9daa9a4772dc9b893c16
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/30911
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
This change provides an interface for canonlake to set TCC.
With this change, we can add code to update Tcc in devicetree.
BUG=b:122636962
TEST=Match the result from TAT UI
Change-Id: Ib54a118e4e409919e3e60112e4621a109404b16d
Signed-off-by: John Su <john_su@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/30803
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
|
|
Invert the default instead of selecting it everywhere. Restores the
ability to use its Kconfig prompt.
Beside Qemu targets, the only platforms that didn't select it seem
to be samsung/exynos5420, intel/cannonlake, and intel/icelake. The
latter two were about to be patched anyway.
Change-Id: I7c5b671b7dddb5c6535c97c2cbb5f5053909dc64
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/30891
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This board has more or less the same as the p5qpl-am except for DDR3
memory and different colors on the ports. Tested with Arch Linux with
kernel 4.20.0-arch1-1-ARCH.
What is tested and works:
- 800/1066/1333 MHz CPUs and DDR3 sticks at 800/1066 MHz
Some bugs are still present in the DDR3 raminit code though.
- Ethernet
- Internal programmer with both coreboot and stock firmware.
- PCI and PCIe x1 slots
- All USB ports
- S3 resume
- SATA ports
- PEG
- Rear audio output
Change-Id: I92cd15a245c4f1d8f57b304c9c3a37ba29c35431
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/27089
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I19e9038eb52922fa0c248936438f27789d00ddb5
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/30876
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Read back the stack guards after most of the romstage took place.
Change-Id: Ia7dc26c7ed1750d4ebbe7514ed87da57f9e34a89
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/30875
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
With the only valid GTT setting being 1M, TSEG_BASE can only be
aligned to TSEG_SIZE if it is also 1M. This alignment requirement
comes from the desire to use SMRR to protect the SMM RAM.
Tested on Foxconn D41S.
Change-Id: Ibd879529923a1676f2e78500797a52d8a37b8eef
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/30869
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
This happens when TSEG is found to be unaligned.
Change-Id: Id0c078a880dddb55857af2bca233cf4dee91250a
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/30709
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
On CPU's with a non eviction mode we cache the whole ROM to speed up
finding the microcode updates, remove the caching to fill in the non
eviction mode and then turn on caching the whole ROM again to speed
executing XIP code in flash.
Change-Id: Ib7f36678913e0ba8ef1305bca2c482f375b23eaf
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/30682
Reviewed-on: https://review.coreboot.org/c/30813
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
This patch revises the pad reset config of speaker reset GPIO pin from
RSMRST to PLTRST. Audio engineer suggested to reset the amps with
warm reset.
BUG=b:122441567
BRANCH=None
TEST=warm & cold reset & suspend_stress_test -c 10 and ensure the
speakers are working well.
Change-Id: I87c554b186b068da93e1662a97afaf01dddae0ef
Signed-off-by: Gaggery Tsai <gaggery.tsai@intel.com>
Reviewed-on: https://review.coreboot.org/c/30866
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Update mainboard UART Kconfig for Whiskylake RVP.
TEST=Build and test on Whiskylake RVP.
By default we can still get console from cbmem, and
enable CONSOLE_SERIAL can get logs from UART port2.
Select other Coffeelake RVPs and check CONSOLE_SERIAL is enabled.
Change-Id: Ic56c019a12b467e5bede5648098d3fb82b56ba7e
Signed-off-by: Wonkyu Kim <wonkyu.kim@intel.com>
Reviewed-on: https://review.coreboot.org/c/30861
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
|
|
The mainboard_romstage_entry function is mostly boilerplate, so move
it to a common location and provide mainboard specific callbacks.
Change-Id: I33cf1d6a60d272f490f41205ec725dee8b00242b
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/30851
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Change-Id: I6ca83bde61f231b9f79c90af1d6c1cfa1a027768
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/30852
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
PLT_RST_L was asserted twice at boot-up and a glitch was observed
when coming out of suspend mode. Configure PLT_RST_L pad IOSSTATE
from HIZCRx1 to be masked.
BRANCH=octopus
BUG=b:117302959
TEST=Verified no glitch on PLT_RST_L at S3 and PLT_RST_L stays high
3.3v during S0ix.
Change-Id: I8c23aadda72be54fb45e67aab2bc8ed51e473bae
Signed-off-by: John Zhao <john.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/c/30815
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
When rmodule is loaded CPU stack alignment is only guaranteed
to 4kiB. Implementation of cpu_info() requires that each
CPU sees its stack aligned to CONFIG_STACK_SIZE.
Add one spare CPU for the stack reserve, such that alignment can
be enforced runtime.
Change-Id: Ie04956c64df0dc7bb156002d3d4f2629f92b340e
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/26302
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Some usb devices exhibits signal loss which causes xHCI entering
compliance mode. The resolution is to disable xHCI compliance mode.
BRANCH=octopus
BUG=b:115699781
TEST=Verified usb operation successfully.
Change-Id: I41fecaa43f4b1588a0e4bbfc465d595feb54dd24
Signed-off-by: John Zhao <john.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/c/30817
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Provide options to disable xHCI Link Compliance Mode. Default is FALSE
to not disable Compliance Mode. Set TRUE to disable Compliance Mode.
BRANCH=octopus
BUG=b:115699781
TEST=Verified booting to kernel.
Change-Id: I2a486bc4c1a8578cfd7ac3d17103e889eaa25fe4
Signed-off-by: John Zhao <john.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/c/30816
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Integrated BT controller in CnVi uses USB port 10 for communication.
BUG=b:122552619
TEST=lsusb shows BT device
Change-Id: Iad1ca0e9419b534f50a3ce3fdcbd660caf8efb5c
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-on: https://review.coreboot.org/c/30809
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I85ca631dfb01acb92dd1ac38dff07215114cab8c
Signed-off-by: Peter Lemenkov <lemenkov@gmail.com>
Reviewed-on: https://review.coreboot.org/c/30802
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Apparently coreboot still uses magic numbers instead of macros in some
Lenovo mainboards. Let's use macros instead.
Note that IOTR[0123] is a 64-bit width variable.
Change-Id: Icf185c77ede5a258fe37be9e772be6804d014b57
Signed-off-by: Peter Lemenkov <lemenkov@gmail.com>
Reviewed-on: https://review.coreboot.org/c/29208
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
This commit follows up on commit 2e464cf3 with Change-Id
I61fb3b01ff15ba2da2ee938addfa630c282c9870.
Change-Id: Iaf06d347e2da5680816b17f49523ac1a687798ba
Signed-off-by: Peter Lemenkov <lemenkov@gmail.com>
Reviewed-on: https://review.coreboot.org/c/29236
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: David Guckian
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Move early_mainboard_romstage_entry before console_init.
Allows to setup a SuperIO, if any, for serial console.
Change-Id: I370263a6197a4c0c805352f07fedddbee1b8e247
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/30828
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Useful for debugging FSP.
Change-Id: I06e837cf1b051c55a531c3361e94fa1449bc8526
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/30741
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Jay Talbott <JayTalbott@sysproconsulting.com>
|
|
* Disable FSP serial output if not CONSOLE_SERIAL
Tested on wedge100s.
Change-Id: Idd825d2d6eb423452d3e81265860205980f6aa5b
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/30706
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Change-Id: Ieff6041f3c9ad02f9cebae0ec83d0898abb0d601
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/18538
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Note that IMC must sleep while SPI writes are in progress.
Instead of using these ACPI methods, flashrom currently does
raw IO to achieve the same.
Change-Id: Ifca4e8328c54d1074b4799ddecfece24607214db
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/18537
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
IMC is used on some of the AMD reference designs, so do not
touch them yet.
Change-Id: I6a58ab53d4a800d4c0c2026e50826122ece2c59f
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/21190
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Michał Żygowski <michal.zygowski@3mdeb.com>
|
|
IMC is used on some of the AMD reference designs, so do not
touch them yet.
Change-Id: Iae21e0294f0155f07fb4f4348ebc5b3120d50fd1
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/18536
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Only a few boards are using IMC for the onboard fan control,
so regarding the availability of IMC selection it should be opt-in,
not opt-out. Also, select HUDSON_IMC_ENABLE for Gizmo 2
because Gizmo 2 could use IMC for the onboard fan control.
Signed-off-by: Mike Banon <mikebdp2@gmail.com>
Change-Id: I3590b13c3b155405d61e373daf1bd82ca8e3bd16
Reviewed-on: https://review.coreboot.org/c/30756
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Required for ACPI S3 suspend support at some motherboards.
Synchronizing with flashchips.c/h flashrom source code.
Signed-off-by: Mike Banon <mikebdp2@gmail.com>
Change-Id: Ic5bd3e43e0d3fd5f454fae71b307c0682f203d5c
Reviewed-on: https://review.coreboot.org/c/30884
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Required for ACPI S3 suspend support at some motherboards.
Synchronizing with flashchips.c/h flashrom source code.
Signed-off-by: Mike Banon <mikebdp2@gmail.com>
Change-Id: I8c0e6d8f1487ca90f88d4a56af3fb0e21458ef1e
Reviewed-on: https://review.coreboot.org/c/30883
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Required for ACPI S3 suspend support at some motherboards.
Synchronizing with flashchips.c/h flashrom source code.
Signed-off-by: Mike Banon <mikebdp2@gmail.com>
Change-Id: I333c8589ddc2bece488608ff66015ca8307eae0f
Reviewed-on: https://review.coreboot.org/c/30882
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Required for ACPI S3 suspend support at some motherboards.
Synchronizing with flashchips.c/h flashrom source code.
Signed-off-by: Mike Banon <mikebdp2@gmail.com>
Change-Id: I4508a65a5bdcbf58aadf452de5e896fc3c5b1bc3
Reviewed-on: https://review.coreboot.org/c/30877
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Add S25FL208K (ID 0x4014), S25FL132K (ID 0x4016) and S25FL164K (ID 0x4017)
chips in a way similar to S25FL116K (ID 0x4015) chip from the same family.
Signed-off-by: Mike Banon <mikebdp2@gmail.com>
Change-Id: I9bf7197bbc0d12797c8ed100c673628de9c140f7
Reviewed-on: https://review.coreboot.org/c/30874
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
butterfly is a Sandybridge device, and selecting Ivybridge
breaks libgfxinit currently due to CPU mismatch
Test: build/boot butterfly w/libgfxinit
Change-Id: I1a7f5a3681d21a256834b11b545855c4365f5f78
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/30820
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Required for functional internal display on butterfly using libgfxinit.
Test: boot/build butterfly, verify internal display functional
prior to OS driver loading.
Change-Id: Ib8060f2d1ad0694f0886d35c83763907f61b47b1
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/30819
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Use hexdump() instead of dump_mem().
Change-Id: I7f6431bb2903a0d06f8ed0ada93aa3231a58eb6f
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/29853
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: David Guckian
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
It's supposed to be the same device that is passed to the executing
function.
Change-Id: I6cf994390c16e0393c96a2b2e04a36305be88e68
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/30880
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Also removes one call for 0:2.0 (integrated graphics) that might be
disabled.
Change-Id: I494aa366030b77baf431f29ba331f13f7c567025
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/30881
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
In these cases we have to expect a NULL pointer because the IGD
device 0:2.0 may be disabled.
The behaviour still differs from using dev_find_slot(), which may
return a disabled device. Though, if you'd try to read its config
space you'd only read garbage (0xff) and in cases where we filled
ACPI data with devicetree information, the information shouldn't
be interpreted by the OS because of the disabled device.
Change-Id: I1bab8fa3a82daca71d03453315cdd69d8951fc24
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/30879
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Superseeded with DEBUG_CONSOLE_INIT.
For dbgp_print_data() return early and skip reading
registers when dprintk() would not get printed anyways.
Change-Id: Idf470b8572ad992c8d4684a860412d9140f514ca
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/30878
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Under normal circumstances no printk() goes through until
console_hw_init() has completed. This is wanted behaviour,
except when you need to debug the setup of one of consoles.
Change-Id: Ifc2bb22bf930009ee229d4461f512ada3018307b
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/30558
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Add placeholder for future flapjack additions/modifications.
BUG=None
BRANCH=kukui
TEST=build with kukui/flapjack configurations
Signed-off-by: YH Lin <yueherngl@google.com>
Change-Id: Ib9cd39e284f19b9179da73ed9f2b13d97442960e
Reviewed-on: https://review.coreboot.org/c/30859
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This board is the only user of these ancient chipsets,
so we'll do all in one go.
Also wipe out some extra headers.
Change-Id: I22c172d577e6072562d8fcfa58145ec62473823e
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/30688
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
This was used to check romcc-built bootblock and romstage
agree about the location of 16-bit entrypoint. There was
no need to customize it as bootblock size requirement did
not grow. Just check for a fixed location at 4 GiB - 4 KiB.
With C_ENVIRONMENT_BOOTBLOCK we can have a proper symbol
for the purpose, since it appears in the same compilation
unit. It will adjust if C_ENV_BOOTBLOCK_SIZE changes.
Change-Id: I93f3c37e78ba587455c804de8c57e7e06832a81f
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/30854
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
This updates the BSP microcode during CAR setup.
Change-Id: I87d34cf38dbd700ecb04d87c5b4767910e4a922c
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/30682
Reviewed-on: https://review.coreboot.org/c/30777
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Hook Coffeelake U43e and Coffeelake H/S/E3 microcode into SOC and remove
the MICROCODE_BLOB_NOT_HOOKED_UP.
BUG=N/A
TEST=Boot up with coffeelake rvp board and check microcode revision in
coreboot log.
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: I6593081374dd4898a82db5b43c3b5bf154b3ef60
Reviewed-on: https://review.coreboot.org/c/30864
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch adds a workaround for ThP2. The PCIe root port LCTL2.TLS
is by default GEN1 and ThP has bad synchronization on polarity
inversion. When the root port request for speed change, ThP doesn’t
confirm the request, and both sides are moving to polling after
timeout, hot reset is issued, and then most of the CFG space is
initialized. From the observation, CCC/ECPM/LTR would be reset to
default but CCC/ECPM of root port and end devices have been
reconfigured in pci_scan. The LTR configuration for root port
is still missing.
BUG=B:117618636
BRANCH=None
TEST=Warm/cold reset for 10 times and didn't see unsupported request
related AER error messages & $lspci -vvs 00:1c.0|grep LTR and
ensure LTR+ is presenti & $iotools pci_read32 0 0x1c 0 0x68
and ensure bit10 is set.
Change-Id: Id5d2814488fbc9db927edb2ead972b73ebc336ce
Signed-off-by: Gaggery Tsai <gaggery.tsai@intel.com>
Reviewed-on: https://review.coreboot.org/c/30486
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
After f5ca922 (Untangle CBFS microcode updates) got merged, all
mainboard using intel apollolake, cannonlake, coffeelake, glk,
kabylake, skylake, icelake and whiskeylake get affected.
Using INTEL_LPSS_UART_FOR_CONSOLE instead of UART_DEBUG
and set default console for each platform.
BUG=N/A
TEST=Build and test on Sarien platform, by default we can still get
console from cbmem, and enable CONSOLE_SERIAL can get logs from UART
port 2.
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: I550a00144cff21420537bb161c64e7a132c5d2de
Reviewed-on: https://review.coreboot.org/c/30853
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Bora Guvendik <bora.guvendik@intel.com>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
With the commit a96e66a (soc/intel: Clean mess around UART_DEBUG), an
adjustment is necessary for this mainboard.
Change-Id: I0fb6288959f8bcb45c4cc93cc132f31a5ab2a5ad
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/30836
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
This reverts commit 6fffd70435084fb1d3237fcb1a11f11849721e8f.
Doing more tests on the Asus KGPE-D16, it seems to cause a reboot loop
quite often. Therefore, revert the commit.
The problem might be caused by the spinlocks used by `get_option()`, and
which are not used by `read_option()`.
Change-Id: Ic25129aa71c8e8e40a65bb2658de78005766fea8
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-on: https://review.coreboot.org/c/30830
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
The Kconfig declaration for FIXED_UART_FOR_CONSOLE was accidentally
placed inside an `if CONSOLE_SERIAL` in a96e66a (soc/intel: Clean mess
around UART_DEBUG).
TEST=Start a clean config, select intel/leafhill and disable serial
console. Confirm that config can be saved without error.
Change-Id: Ie41687e91af11a13697cbe25938dada2c74b40fb
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/30829
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Clearing the EBDA was introduced with b4aaaa "Prepare the BIOS data
areas before device init." which states that the purpose of setting up
these area's is just to make sure they are sane. On the S3 path doing
this is not needed and can even thrash data set up by payloads (mostly
SeaBIOS) that used that memory.
Change-Id: I9c54156bd8247e8a34dec6edc27cfc2d33cde595
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/30789
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Change-Id: Ie3c2d2e1bc79dcaffd9901e17f83ceeaabd1d659
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/30682
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
It was already done once in c_start.S.
Change-Id: I1cb0ea25251644dbd1127d177247a02ba52bb550
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/30796
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Enable the EC_AP_INT_ODL interrupt on GPIO_134 for all octopus boards
that support it. Also removing unnecessary IO standby support since we
don't use this pin to wake up the SoC.
BRANCH=octopus
BUG=b:122552125,b:120679547
TEST=CTS tests with changes
Change-Id: I018864ae5fa400372b5b443e49828e8202b9aa4d
Signed-off-by: Jett Rink <jettrink@chromium.org>
Reviewed-on: https://review.coreboot.org/c/30788
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
It's been hooked up in the meantime.
Change-Id: I64176b09e375034189000ea4308c58771f0019a1
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/c/30812
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
PCI_ADDR() is tightly coupled with different setup_resource_map()
variants so move the declaration away from global namespace.
In the implementation of setup_resource_map() use the bottom
12 bits as the register mask like the other variants do already.
Change-Id: Iadedfe993621a4458ce8f12c5e98c8cee537d2db
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/30784
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Purpose of the table is to load initial address maps
on PCI function 0:18.1. Provide a macro of its own so
it is clear no other PCI devfn is accessed here.
Change-Id: Ic146207580a5625c4f6799693157b02422bef00a
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/30783
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
What you see in the table are not the PCI devices
that will be written to. Use a helper MCP55_DEV()
to make you look twice what is actually done.
Change-Id: I1349af9f734aaabb576d1370ae29a56c91569a7c
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/30782
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|