| Age | Commit message (Collapse) | Author |
|---|
|
Transaction consistently completes with 80 to 150 status reads on my
setups. Hardware should always be able to complete this within 125us
as the debug port is serviced at the beginning of each microframe.
Timeout is set to DBGP_MICROFRAME_TIMEOUT_LOOPS=1000 status reads. Do not
retry transactions if this timeout is reached as the host controller
probably needs full re-initialisation to recover.
If this timeout is not reached, but a transaction is corrupted
on the wire, or it is otherwise not properly delivered to the USB device,
transaction is retried upto DBGP_MICROFRAME_RETRIES=10 times.
Change-Id: I44bc0a1bd194cdb5a2c13d5b81fc39bc568ae054
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3881
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
|
|
These allow to define a kernel image, initrd and command line.
Change-Id: I40155b812728a176b6d15871e1e6c96e4ad693c8
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/3893
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
|
|
It wasn't even hooked up to the build system anymore.
Change-Id: I4b962ffd945b39451e19da3ec2f7b8e0eecf2e53
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/3892
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
|
|
Add support for control messages with a write of data stage.
Add status stage after a read of non-zero length data stage.
Do not retry control message if device responds with STALL.
Change-Id: I16fb9ae39630b975af5461b63d050b9adaccef0f
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3867
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
|
|
USB defines a mechanism to detect certain cases of lost handshakes
using an alternating data sequence number, referred to as data
toggling. This patch fixes each pipe to have its own tracking of
the data toggle state.
Change-Id: I62420bdaeadd0842da3189428a37eeb10c646900
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3865
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
|
|
Add allocation for endpoint0 as a pipe for control messages.
Endpoint number was already stored in the pipe object, place devnum
there too, although all pipes will use same devnum==127.
Change-Id: I299d139bdd8083af8b04a694e8e41435ec026a25
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3864
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
|
|
Add option to choose one of the EHCI controllers in recent
intel chipsets for usbdebug use.
Since EHCI controller function changes from 0:1d.7 to 0:1d.0 in
rcba_config() for some mainboards, check the PCI class code
for match.
Change-Id: I18a78bf875427c163c857c6f0888935c1d2a58d4
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3440
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
|
|
Nowadays, chipsets or boards do not only have one USB port with the
capabilities of a debug port but several ones. Some of these ports are
easier accessible than others, so making them configurable is also necessary.
This change adds infrastructure to switch between EHCI controllers,
but does not implement it for any chipset.
Change-Id: I079643870104fbc64091a54e1bfd56ad24422c9f
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3438
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
|
|
On AMD platforms, setting of USBDEBUG_DEFAULT_PORT=0 tries to scan
all physical ports one after other in incrementing order. To avoid
possible problems with other USB devices, one can select the port
number here and bypass the scan.
Intel platforms can communicate with usbdebug dongle on one
physical port only, and this option makes no difference there.
Change-Id: I45be6cc3aa91b74650eda2d444c9fcad39d58897
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3872
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
|
|
Two new nvram variables control disabling the two non-ME NICs
on the mainboard. This is implemented by disabling their PCIe bridge.
Change-Id: I086f0d79de3ad0b53fa0ec40648d63378070e3bd
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/3870
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Collect early timestamps in Lenovo X60’s romstage.
Selecting the option `COLLECT_TIMESTAMPS` in Kconfig and then
doing `cbmem --timestamps` should output the timestamps.
Change-Id: I7bd30f03a1b85c38e89c19cdf88b2d20b24abed8
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/3587
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
|
|
Change-Id: Ia4a5530e6a1a1fd2dec6f348ff163b5c7a8cd4cd
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/3830
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
The northbridge defines it already and to the same value.
Change-Id: Ia5d856258fac52ea0b249142f70a89123ca04f82
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/3876
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Change-Id: I79937fd1671af23184ab830d5ba6242c8067d944
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/3831
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Change-Id: Ic4d191bd34179af707449a15026079da1412ed60
Signed-off-by: Bruce Griffith <Bruce.Griffith@se-eng.com>
Reviewed-on: http://review.coreboot.org/3886
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
Tested-by: build bot (Jenkins)
|
|
Tested on Ubuntu 12.10. S3 is supported. No HD Audio.
Mainboard details: http://www.asrock.com/ipc/overview.asp?Model=IMB-A180
Change-Id: I75254194ab5da8e5c61383d8f85aa4e300815637
Signed-off-by: WANG Siyuan <SiYuan.Wang@amd.com>
Signed-off-by: WANG Siyuan <wangsiyuanbuaa@gmail.com>
Reviewed-on: http://review.coreboot.org/3880
Reviewed-by: Bruce Griffith <Bruce.Griffith@se-eng.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
|
|
src/southbridge/amd/agesa/hudson/Kconfig config default value,
mainboard Kconfig config value for specific mainboard.
bit 1,0 - pin 0
bit 3,2 - pin 1
bit 5,4 - pin 2
bit 7,6 - pin 3
Change-Id: I54a87cf734685515a3e1850838ca7d94387172ce
Signed-off-by: WANG Siyuan <SiYuan.Wang@amd.com>
Signed-off-by: WANG Siyuan <wangsiyuanbuaa@gmail.com>
Reviewed-on: http://review.coreboot.org/3879
Tested-by: build bot (Jenkins)
Reviewed-by: Bruce Griffith <Bruce.Griffith@se-eng.com>
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
|
|
Change the defines, as follow-up patch will replace use of
constant CONFIG_EHCI_BAR.
Change-Id: I44ff77cb7a2826f3b43d8d46440fd4482a29d18c
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3875
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
|
|
Add a function to test if pci_devfn_t matches with a device
instance of struct device, by comparing bus:dev.fn.
Change-Id: Ic6c3148ac62c7183246d83302ee504b17064c794
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3474
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
|
|
Declare the functions that may be used in both romstage and ramstage
with simple device model. This will later allow to define PNP access
functions for ramstage using the inlined functions from romstage.
Change-Id: I2a0bd8194acaf9c4c7252a29376eec363397e3a6
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3871
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
|
|
Declare the functions that may be used in both romstage and ramstage
with simple device model. This will later allow to define PCI access
functions for ramstage using the inlined functions from romstage.
Change-Id: I32ff622883ceee4628e6b1b01023b970e379113f
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3508
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
|
|
After an USB device sees USB bus reset on the bus, it will reset to
device number 0. Per the EHCI debug port specification, a debug
dongle device may reset to the fixed debug device number of 127 instead.
Thus there is no need to try device numbers from 1 to 126.
Do a sanity-check on a returned debug descriptor as I experienced
some USB flash memory to respond on this request with zero-fill data.
Change-Id: I78d58f3dc049cd8c20c6e2aa3a4207ad7e6a6d33
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3861
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
|
|
Resetting an EHCI controller when it is not halted can have
undefined behaviour. This mostly fixes a case where calling
usbdebug_init() twice would fail to reset the USB dongle device
properly.
On amd/persimmon it still requires one extra retry, but at least it
is now possible to have usbdebug enabled for both romstage and
ramstage.
Change-Id: Ib0e6e5a0167404f68af2edf112306fdb8def0be9
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3862
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
Ported from spi/winbond.c.
Fixes this error:
ICH SPI: Too much to write.
Does your SPI chip driver use CONTROLLER_PAGE_LIMIT?
Change-Id: I50db8fd1104d3b7d319b278b14f97e3ff9cb6404
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3877
Tested-by: build bot (Jenkins)
Reviewed-by: David Hendricks <dhendrix@chromium.org>
|
|
Letting SMI handler touch EHCI controller is an excellent source
of USB problems. Remove usbdebug entirely from SMM.
It may be possible to make usbdebug console work from SMM
after hard work and coordination with payloads and even
OS drivers. But we are not there.
Change-Id: Id50586758ee06e8d76e682dc6f64f756ab5b79f5
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3858
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Tested-by: build bot (Jenkins)
|
|
This quirk is needed with a DIY debug dongle using obsolete
CY7C68013 (aka FX2) USB chips. Old revision of chip requires a
SET_CONFIGURATION to be sent, while this is not required in EHCI
debug port specs.
Change-Id: I4926eb19b7e991d6efeef782682756571ad006b9
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3386
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
When we create low-level debugging of EHCI controller registers,
we call printk() within printk(). In ramstage this would leave us
with deadlock waiting on the console spinlock.
Change-Id: Idbe029af9af76de27094bb2964c60d9ccfdd96e6
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3860
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Increase existing level from DEBUG to INFO.
Change-Id: Ic5934aec449f921af96dd3a6524f7275f8de1304
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3859
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
If ramstage is not compressed, the CBFS module in romstage doesn't
need to support LZMA. Removing the LZMA module in this case can save
about 3000 bytes in romstage.
Change-Id: Id6f7869e32979080e2985c07029edcb39eee9106
Signed-off-by: Andrew Wu <arw@dmp.com.tw>
Reviewed-on: http://review.coreboot.org/3878
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Change-Id: Ic7d793754a8b59623b49b7a88c09b5c6b6ef2cf0
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/3768
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Change-Id: Ia2dff49d3e2b086546785d992f2d92bcf4d1ef1c
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Reviewed-on: http://review.coreboot.org/3376
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
The AMD AGESA function to move the stack from cache-as-ram to
actual RAM doesn't need any help. The current implementation has
an INVD instruction just before cache-as-RAM is torn down. It isn't
needed for Trinity processors and makes Kabini boot unreliable.
Change-Id: Ibe9e4105eee032471ccbb2d537471d5fa5847d22
Signed-off-by: Bruce Griffith <bruce.griffith@se-eng.com>
Reviewed-on: http://review.coreboot.org/3852
Tested-by: build bot (Jenkins)
Reviewed-by: Siyuan Wang <wangsiyuanbuaa@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
|
|
It still pointed to the old binary despite implementing the newer interface
Change-Id: Iebd5dae98168f5568f3ad6a18c5ebde9abc3ece0
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/3869
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Drop unused and commented out variable, and fix a comment while at it.
Change-Id: I1bd7d10aca949c8579433ea1c91264fd816a3fb4
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/3873
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
SEABIOS_PS2_TIMEOUT needs a default, otherwise the "allyesconfig" target
hangs in an endless loop.
The given default is correctly overridden by the (currently sole) user,
the lenovo/x60 target.
Change-Id: I3f5e347c29ccbb4d711a489d067b6c909f030bd0
Reported-by: Kyösti Mälkki
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/3874
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins)
|
|
Add Kconfig option SQUELCH_EARLY_SMP and have it enabled by
default.
Console drivers have unpredictable results if multiple threads
attempt to share same resources without spinlock. Serial UARTs
have not had huge problems, only distorted output, but those
relying on cache-as-ram (CBMEM and usbdebug) may require this.
Change-Id: I7f406fdea7b6dc6a341c4da2fab56f7b7ff568b4
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3854
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@google.com>
|
|
Move the floppy drive enumeration from _INI() and PROB(),
which stored the enumeration results into _FDE into _FDE().
_INI is called by any ACPI-capable OS on boot while _FDE
is rarely used. So it's better to run the enumeration when
requested rather than unconditionally.
Change-Id: Icf1e2a551806592faa8ba8d80fa8d02681602007
Signed-off-by: Christoph Grenz <christophg+cb@grenz-bonn.de>
Reviewed-on: http://review.coreboot.org/3604
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
The parallel port of the W83627HF can be configured on any port
between 0x100 and 0xFFC with 4 byte alignment for traditional modes
and 8 byte alignment for EPP mode. As the ACPI specification says
that the maximum acceptable starting address has to be a multiple
of the alignment granularity, correct the maximum starting address
from 0xFFC to 0xFF8.
Change-Id: I272e09d091149791f2867b1d06e4fc27bc1bb2cd
Signed-off-by: Christoph Grenz <christophg+cb@grenz-bonn.de>
Reviewed-on: http://review.coreboot.org/2942
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
ROMCC boards were left unmodified.
Change-Id: I3d842196b3f5b6999b6891b914036e9ffcc3cef0
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3853
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
This allows mainboards to preconfigure a ps2-keyboard-spinup
timeout when SeaBIOS is chosen as the payload.
The Kconfig option can be changed manually if CONFIG_EXPERT is set.
Change-Id: I5732b18ef04f4bdef6236f35039656ad02011aec
Signed-off-by: Peter Stuge <peter@stuge.se>
Reviewed-on: http://review.coreboot.org/3734
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
The slightly hackish ioapic ressource reservation is needed for i440fx
emulation only, for q35 the ich9 southbridge driver handles this just
fine.
[ Side note: The i440fx chipset emulated by qemu is pimped up with alot
of stuff which never existed on real hardware, which leads
to tweaks like this one. ]
Change-Id: I06bf54cbc247ccf17aa9063fb7dee9def323c605
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-on: http://review.coreboot.org/3850
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Use the same HD Audio [1] verb table for the Realtek ALC887-VD
audio chip as the one set up by the proprietary vendor BIOS.
Linux’ ALSA exposes this pin configuration under the virtual
filesystem sysfs.
/sys/class/sound/hwC1D0/init_pin_configs
The script `alsa-info.sh` [2][3] is able to decode the table.
Only one channel audio playback (rear connectors) is tested [4],
which worked already before.
[1] http://en.wikipedia.org/wiki/Intel_High_Definition_Audio
[2] http://mailman.alsa-project.org/pipermail/alsa-devel/2013-March/060717.html
[3] http://alsa-project.org/main/index.php/Help_To_Debug
[4] http://review.coreboot.org/#/c/3170/2//COMMIT_MSG
Change-Id: I17fa2d4ab1e1a6bfd84de94e9e4a91bd67b6a0c0
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/3170
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
|
|
The board name in that variable name is not necessary, as it is not board
dependent, that means using the file as a template for making a new
coreboot port for another motherboard the variable does not need to be
changed, and just increases the code differences between AMD Parmer,
AMD Thather and ASUS F2A85-M. So use a generic name.
The same was done for AMD Persimmon (and inherited by the LiPPERT
FrontRunner/Toucan-AF) in the following commit.
commit 5e70766f14253f53190ddd49a544460c6bc1e528
Author: Jens Rottmann <JRottmann@LiPPERTembedded.de>
Date: Tue Feb 26 15:56:11 2013 +0100
AMD Fam14 boards: reduce unnecessary differences, 2nd attempt
Reviewed-on: http://review.coreboot.org/2529
The board name is *not* removed from the `CODEC_ENTRY` variable name as
the verb table not only depends on the codec but also on the board [1].
Having the board name in the variable name is a good indicator that the
pin configuration needs to be adapted when taking this file as a template
for a new port. If it was board independent, a default chip configuration
could be used and shared between all boards, which is unfortunately not
the case.
[1] Unfortunately I was not able to find Jens’ comment in my mail archive
and in the Gerrit Web interface. Not sure where it is, but I am sure
he made that comment.
Change-Id: I440a306cf4ff0a5b1b61d1983d70c66d129904d0
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/3199
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
As Nico noticed for the W83627DHG, the power management bits to power down
individual logical devices on Winbond superios are named counterintuitively
and need to be set when the logical device should be powered.
This corrects the power management methods for the W83627HF.
Change-Id: I98bccd550a0513c62bfa9480275f88c566691bc8
Signed-off-by: Christoph Grenz <christophg+cb@grenz-bonn.de>
Reviewed-on: http://review.coreboot.org/3605
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
For reasons explained in a previous CL, it might be necessary to "load" a file
from CBFS in place. The loading code in CBFS was, however, zeroing the area of
memory the stage was about to be loaded into. When the CBFS data is located
elsewhere this works fine, but when it isn't you end up clobbering the data
you're trying to load. Also, there's no reason to zero memory we're about to
load something into or have just loaded something into. This change makes it
so that we only zero out the portion of the memory between what was
loaded/decompressed and the final size of the stage in memory.
Change-Id: If34df16bd74b2969583e11ef6a26eb4065842f57
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3579
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Instead of returning 0 on success and -1 on error, return the decompressed
size of the data on success and 0 on error. The decompressed size is useful
information to have that was being thrown away in that function.
Change-Id: If787201aa61456b1e47feaf3a0071c753fa299a3
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3578
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
The ThinkPad keyboard controller sometimes needs a while in order
to initialize, so let's ask SeaBIOS to wait for it.
This change ensures that the internal keyboard always functions
correctly on the ThinkPad when coreboot is built with SeaBIOS as
payload.
Change-Id: I562475ec98b0c1f5d0debf6e9b597748a420f068
Signed-off-by: Peter Stuge <peter@stuge.se>
Reviewed-on: http://review.coreboot.org/3735
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
|
|
QEMU has a bunch of non-standard virtual devices on various I/O ports.
Allocate resources for them so the coreboot resource management knows
those ports are used.
Change-Id: I51a85967cf2dcd634b0c883210bb52c0c34c8283
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-on: http://review.coreboot.org/3851
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Change-Id: Ic7fdedc0a22e7664f14b105f2f7cecd8f55980be
Signed-off-by: Bruce Griffith <Bruce.Griffith@se-eng.com>
Reviewed-on: http://review.coreboot.org/3857
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
|
|
The _OSC method is used to tell the OS what capabilities it can
take control over from the firmware. This method is described
in chapter 6.2.9 of the ACPI spec v3.0. The method takes 4
inputs (UUID, Rev ID, Input Count, and Capabilities Buffer) and
returns a Capabilites Buffer the same size as the input Buffer.
This Buffer is generally 3 Dwords long consisting of an Errors
Dword, a Supported Capabilities Dword, and a Control Dword.
The OS will request control of certain capabilities and the
firmware must grant or deny control of those features. We do not
want to have control over anything so let the OS control as much
as it can.
The _OSC method is required for PCIe devices. During Linux boot,
an error is logged to dmesg if _OSC is not found.
Change-Id: Icf6e7a82284d03d23fd30ee7b7db17754e988c9a
Signed-off-by: Mike Loptien <mike.loptien@se-eng.com>
Reviewed-on: http://review.coreboot.org/3823
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Adding the 'WordBusNumber' macro to the PCI0
CRES ResourceTemplate in the AMD FCH ACPI code.
This sets up the bus number for the PCI0 device
and the secondary bus number in the CRS method.
This change came in response to a 'dmesg' error
which states:
'[FIRMWARE BUG]: ACPI: no secondary bus range in _CRS'
By adding the 'WordBusNumber' macro, ACPI can set
up a valid range for the PCIe downstream busses,
thereby relieving the Linux kernel from "guessing"
the valid range based off _BBN or assuming [0-0xFF].
The Linux kernel code that checks this bus range is
in `drivers/acpi/pci_root.c`. PCI busses can have
up to 256 secondary busses connected to them via
a PCI-PCI bridge. However, these busses do not
have to be sequentially numbered, so leaving out a
section of the range (eg. allowing [0-0x7F]) will
unnecessarily restrict the downstream busses.
Change-Id: Ib2d36f69a26b715798ef1ea17deb0905fa0cad87
Signed-off-by: Mike Loptien <mike.loptien@se-eng.com>
Reviewed-on: http://review.coreboot.org/3822
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Split the Family16 (Kabini) DSDT file into logical regions.
Olive Hill is the only mainboard and Kabini is the only NB/CPU
currently using Family16 AGESA code.
Change-Id: I9ef9a7245d14c59f664fc768d0ffa92ef5db7484
Signed-off-by: Mike Loptien <mike.loptien@se-eng.com>
Reviewed-on: http://review.coreboot.org/3821
Tested-by: build bot (Jenkins)
|
|
Hook this up into the DMP Vortex86EX. Before under Windows XP
the microphone did not work. With the new logic it does. Now
line-in,line-out and microphone all work.
The verb data table is generated by Realtek.
Change-Id: I1bcef898a15547c86c12c4b52ce0069d13e23c84
Signed-off-by: Andrew Wu <arw@dmp.com.tw>
Reviewed-on: http://review.coreboot.org/3855
Tested-by: build bot (Jenkins)
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
|
|
This module uses cim_verb_data to detect and initialize HD audio
codecs.
The module source code is based on southbridge/intel/sch/audio.c and
southbridge/nvidia/mcp55/azalia.c.
Change-Id: I810fef6fdcf55d66f62da58c3d7d99f006559d6e
Signed-off-by: Andrew Wu <arw@dmp.com.tw>
Reviewed-on: http://review.coreboot.org/3844
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
|
|
codec_init expects wait_for_valid returns -1 for timeout, not 1.
Change-Id: I0f2a3ebb1934d0adaf13765434526bbc9efca9a3
Signed-off-by: Andrew Wu <arw@dmp.com.tw>
Reviewed-on: http://review.coreboot.org/3843
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Add option to log changes in USB 2.0 EHCI debug port connection.
For romstage move usbdebug as the last initialised console so one
actually can see these messages.
Init order of consoles in ramstage is undetermined and unchanged.
Change-Id: I3aceec8a93064bd952886839569e9f5beb6c5720
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3387
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
|
|
These Kconfig entries were forgotten from the commit
that re-enabled usbdebug for these southbridges.
Change-Id: Ia17f1dd3340408da7c033c2c949404d2636bed44
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3849
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
|
|
Now that MMCONF_SUPPORT_DEFAULT is enabled by default remove
the pcie explicit accesses. The default config accesses use
MMIO.
Change-Id: I58c4b021ac87a035ac2ec2b6b110b75e6d263ab4
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3810
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
|
|
Rearranged the F2A85-M DSDT file to match the functionality found
on Parmer. As with the Parmer implementation, the F2A85-M dsdt.asl
file in the mainboard directory contains only #include references to
the appropriate files.
As with Parmer, some include files have no content but are left as a
template for other platforms and as placeholders for completing the
ACPI implementation for F2A85-M.
Change-Id: Ic72cb6004538ca9d9f79826b9b3c8d6aeb25017c
Signed-off-by: Kimarie Hoot <kimarie.hoot@se-eng.com>
Reviewed-on: http://review.coreboot.org/3805
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin@se-eng.com>
|
|
Rearranged the Thatcher DSDT file to match the functionality found
on Parmer. As with the Parmer implementation, the Thatcher dsdt.asl
file in the mainboard directory contains only #include references to
the appropriate files.
As with Parmer, some include files have no content but are left as a
template for other platforms and as placeholders for completing the
ACPI implementation for Thatcher.
Change-Id: Ie44a32959cc547840914365e872416d4624d33df
Signed-off-by: Kimarie Hoot <kimarie.hoot@se-eng.com>
Reviewed-on: http://review.coreboot.org/3804
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin@se-eng.com>
|
|
Support code for sb700 and sb800 existed already, but Kconfig and
compile-time issues prevented from enabling USBDEBUG for boards
with the affected AMD southbridges.
Change-Id: I49e955fcc6e54927320b9dc7f62ea00c55c3cedf
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3439
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
|
|
With USBDEBUG selected, the file is built for both romstage and
ramstage. For the ramstage build, we need to explicitly use the
simple PCI config operations without devicetree.
Change-Id: I2de8d9c77bb458ba797c3aac9e2cd0d653e06684
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3437
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
|
|
This change brings back the possibility to disable console
output while in romstage, like before commit d2f45c65.
For some platforms (AMD multi-socket) USBDEBUG and/or CBMEM
CONSOLE do not work correctly for romstage due the way
cache-as-ram is set up, but might already work for ramstage.
Change-Id: Id8d830e02a18129af419d3b5860866acf315d531
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3846
Tested-by: build bot (Jenkins)
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
Reviewed-by: Aaron Durbin <adurbin@google.com>
|
|
Copied from a similar commit for Family 10h AGESA [1]
Remove the fourth argument in the comments. Luckily the compiler,
at least gcc, warns about a wrong number of arguments, and therefore
no incorrect code resulted from the wrong documentation.
[1] 07e0f1b AMD AGESA: Fix argument list for `PCIE_DDI_DATA_INITIALIZER` in comments
[2] fc47bfa Revert "AMD f14 vendorcode: Fix warning"
Change-Id: I3806e368a823e4a40d22e99b91bf3598d9ed2f15
Signed-off-by: Bruce Griffith <bruce.griffith@se-eng.com>
Reviewed-on: http://review.coreboot.org/3840
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin@se-eng.com>
|
|
This is the same patch as an earlier one applied to family 15 [1].
Static analysis often flags case statements that do not include
a terminating "break;" statement. Eclipse's CODAN is an example
of this. This changelist modifies amdlib.c to terminate
case statements with "break;".
[1] e44a89f amd/agesa/f15/Lib/amdlib.c: Add missing breaks ...
Change-Id: Ibd1ae6f2b52fde07de3d978d174975f4d93647ab
Signed-off-by: Bruce Griffith <Bruce.Griffith@se-eng.com>
Reviewed-on: http://review.coreboot.org/3839
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin@se-eng.com>
|
|
Change-Id: Idf26eb3fb541355bd9553c1897f647738c347eb5
Signed-off-by: Bruce Griffith <bruce.griffith@se-eng.com>
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
Reviewed-on: http://review.coreboot.org/3819
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
|
|
Change-Id: I7f6f6ff444fda4bdf233db1383919772afe6b635
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
Signed-off-by: Bruce Griffith <Bruce.Griffith@se-eng.com>
Reviewed-on: http://review.coreboot.org/3815
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin@se-eng.com>
|
|
Olive Hill does not have a Super I/O or keyboard controller.
Change-Id: I8c1e5d8c20c4a964fe8d98df920b416382a26d9d
Signed-off-by: Bruce Griffith <Bruce.Griffith@se-eng.com>
Reviewed-on: http://review.coreboot.org/3848
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin@se-eng.com>
|
|
The VBIOS device ID is set by processor family using the
map_oprom_vendev() function in the northbridge code. There
is rarely a reason why this should be overridden by the mainboard.
Since Kabini includes a default VBIOS vendor/device ID in the
northbridge Kconfig code, remove the setting from the Olive Hill
mainboard settings.
Change-Id: Icd69155f5b51105d564dd82c89e4bb54a6118a82
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
Signed-off-by: Bruce Griffith <Bruce.Griffith@se-eng.com>
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
Tested-by: Bruce Griffith <bruce.griffith@se-eng.com>
Reviewed-on: http://review.coreboot.org/3816
Tested-by: build bot (Jenkins)
|
|
Add CONST modifiers to read-only pass-by-reference function
parameters in AGESA. This allows the use of "const" modifiers
on the declaration of lookup tables that are pass-by-reference.
These will be used to identify tables that are copied onto the
HEAP but don't need to be.
This same change was made for AMD Trinity APUs (Family15tn) [1].
[1] 283ba78 AGESA: Add "const" modifier to function parameters
Change-Id: I2bdd9fc5e027e938de9df0f923b95da934bb48dc
Signed-off-by: Bruce Griffith <Bruce.Griffith@se-eng.com>
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
Tested-by: Bruce Griffith <bruce.griffith@se-eng.com>
Reviewed-on: http://review.coreboot.org/3837
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
|
|
This changelist was cherry-picked from merged community code
for Parmer [1] and the paths modified so that the Parmer
modification is applied against Olive Hill.
[1] 0086162 AMD SATA: Correct _them implement_ ... in comments
Change-Id: I9849e9a75dacfde15331c4200d72343a59036f14
Signed-off-by: Bruce Griffith <bruce.griffith@se-eng.com>
Reviewed-on: http://review.coreboot.org/3841
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Change-Id: I14285f0677003fbf8b9b112207af202658807894
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
Signed-off-by: Bruce Griffith <Bruce.Griffith@se-eng.com>
Reviewed-by: Bruce Griffith <bruce.griffith@se-eng.com>
Tested-by: Bruce Griffith <bruce.griffith@se-eng.com>
Reviewed-on: http://review.coreboot.org/3806
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
|
|
Change-Id: Ifc180e6fcd594dbedc2512ea5bef283a3ad689d3
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
Signed-off-by: Bruce Griffith <Bruce.Griffith@se-eng.com>
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
Tested-by: Bruce Griffith <bruce.griffith@se-eng.com>
Reviewed-on: http://review.coreboot.org/3814
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
|
|
Eliminate an unnecessary copy of the DDI descriptor list and
the PCIe port descriptor list. As descriptor tables, these
tables do not need dynamic updating and should be used from
ROM without runtime copying.
There will be a corresponding patch for AGESA that adds CONST
modifiers to function parameters that are pass-by-reference
"IN" values (read-only pointers).
Change-Id: I7ab78e58041e9247db22d0f97a6f76d45f338db0
Signed-off-by: Bruce Griffith <Bruce.Griffith@se-eng.com>
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
Tested-by: Bruce Griffith <bruce.griffith@se-eng.com>
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
Reviewed-on: http://review.coreboot.org/3818
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
|
|
Change-Id: I1f252b67c039d28df96e8dfd458a1ca6a7dbc816
Signed-off-by: Siyuan Wang <SiYuan.Wang@amd.com>
Signed-off-by: Siyuan Wang <wangsiyuanbuaa@gmail.com>
Reviewed-by: Bruce Griffith <bruce.griffith@se-eng.com>
Tested-by: Bruce Griffith <bruce.griffith@se-eng.com>
Reviewed-on: http://review.coreboot.org/3784
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
|
|
This patch sets a bit in the Yangtze southbridge to enable
the extra protocol necessary to handle port multiplier chips.
This has been turned on during most of Kabini development
without any notable impact. Olive Hill has an optional daughter
board that incorporates Silicon Image Steel Vines chips. This
change has been tested with and without the daughter board. This
change can be regression tested using any Hudson-based motherboard,
although it has no impact on boards with discreet Hudson/Bolton
southbridges.
This was tested for impact on SATA performance in the absence of
a port multiplier using the IOZone benchmarks within the Phoronix
Test Suite. A SATA 3 hard drive (6.0 Gbps) and an SSD were
connected to the ports on Olive Hill without using the port
multiplier card. The test results contained more run-to-run
variation within the same configuration than was seen in the
aggregate results comparing the interface with and without the
port multiplier protocol additions. In other words, the test
had less accuracy than the impact caused by turning on port
multiplier support.
Change-Id: Ie87873b093f3e2a6a5c83b96ccb6c898d3e25f72
Signed-off-by: Bruce Griffith <bruce.griffith@se-eng.com>
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
Reviewed-on: http://review.coreboot.org/3808
Tested-by: build bot (Jenkins)
|
|
Yangtze uses Hudson AGESA wrapper code but has some changes.
The changes are necessary and have no effects on Hudson.
Change-Id: Iada90d34fdc2025bd14f566488ee12810a28ac0d
Signed-off-by: Siyuan Wang <SiYuan.Wang@amd.com>
Signed-off-by: Siyuan Wang <wangsiyuanbuaa@gmail.com>
Signed-off-by: Bruce Griffith <Bruce.Griffith@se-eng.com>
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
Tested-by: Bruce Griffith <bruce.griffith@se-eng.com>
Reviewed-on: http://review.coreboot.org/3783
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
|
|
src/arch/x86/boot/tables.c and src/include/device/pci_ids.h are also
changed because these two files depend on F16kb northbridge macros
Change-Id: Iedc842f0b230826675703fc78ed8001a978319c5
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
Signed-off-by: Bruce Griffith <Bruce.Griffith@se-eng.com>
Reviewed-by: Bruce Griffith <bruce.griffith@se-eng.com>
Tested-by: Bruce Griffith <bruce.griffith@se-eng.com>
Reviewed-on: http://review.coreboot.org/3782
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
|
|
Change-Id: I4a1d2118aeb2895f3c2acea5e792fbd69c855156
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
Signed-off-by: Bruce Griffith <Bruce.Griffith@se-eng.com>
Reviewed-by: Mike Loptien <mike.loptien@se-eng.com>
Tested-by: Bruce Griffith <bruce.griffith@se-eng.com>
Reviewed-on: http://review.coreboot.org/3781
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
|
|
Change-Id: Icb6f64e2e3cfd678fb4fb4f13f0e4b678d5acc4a
Signed-off-by: Siyuan Wang <SiYuan.Wang@amd.com>
Signed-off-by: Siyuan Wang <wangsiyuanbuaa@gmail.com>
Reviewed-by: Nick Dill <nick.dill@se-eng.com>
Tested-by: Bruce Griffith <bruce.griffith@se-eng.com>
Reviewed-on: http://review.coreboot.org/3836
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
|
|
Change-Id: I4ed9329126b216eb4ae58355672603ce79a6d4ef
Signed-off-by: Andrew Wu <arw@dmp.com.tw>
Reviewed-on: http://review.coreboot.org/3847
Tested-by: build bot (Jenkins)
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
|
|
Now that MMCONF_SUPPORT_DEFAULT is enabled by default remove
the pcie explicit accesses. The default config accesses use
MMIO.
Change-Id: I71923790aa03e51db01ae3a4745e1c44556d281f
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3812
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
|
|
The tests for __PRE_RAM__ or __SMM__ were repeatedly used
for detection if dev->ops in the devicetree are not available
and simple device model functions need be used.
If a source file build for ramstage had __PRE_RAM__ inserted
at the beginning, the struct device would no longer match the
allocation the object had taken. This problem is fixed by
replacing such cases with explicit __SIMPLE_DEVICE__.
Change-Id: Ib74c9b2d8753e6e37e1a23fcfaa2f3657790d4c0
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3555
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
|
|
The Kconfig variable EXTERNAL_MRC_BLOB is not used.
Drop it.
Change-Id: I3caa5c2b6bcf5d2c13b6987da8ab3987bad0e506
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/3829
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Directory intel/common must be conditionally added in the list
of source directories, as the parent directory southbridge/intel
is unconditionally added even for boards without such device.
Change-Id: I7088bc6db9f56909ffa996aa7eff76cd72e177eb
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3827
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
|
|
Change-Id: I74d28c13e6597c56e3b85ccd2b83386b86c200f0
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3828
Tested-by: build bot (Jenkins)
|
|
The added device.h file was indirectly picked from cpu.h, which will
have this include removed in a follow-up patch.
Change-Id: Ifc0a4800de3b1ef220ab1034934f583be8c527b0
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3826
Tested-by: build bot (Jenkins)
|
|
Change-Id: I08e56b4a1c56128c6d4beb751979c5b99cdae829
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/3790
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Change-Id: Ie52d80fc8657064efdcec51c31dc9309fcc28121
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/3787
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Change-Id: I5f75998356554e08f8c9920e7612494e4710ab15
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/3786
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
The EC expects the temperature in 64ths degree C. Alter
it8516e_set_fan_temperature() to just export this interface and
make the calculation more obvious.
Change-Id: Ibe241b7909f4c02b30b1e1200a1850d47695a765
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/3785
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Change-Id: Ic660efec519a9a970ec5a8832fd1dd8c9516318f
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/3775
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Add an option to set minimal and maximal PWM percentages when the fan is
in temperature controlled mode. Also fix a non-ascii flaw.
Change-Id: I85ae244bee2145bf17d6c29e93dd4871540985c8
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/3774
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
The EC firmware expects a 255th while we provide a percentage.
Change-Id: Ib06a061b431ac728329043179800729e39e6166b
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/3773
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
The IT8516E firmware of Kontron supports some selected external sensors
attached to the EC via SMBUS or GPIO16.
Change-Id: I4c451c360a393e916430e3bea04a95847455cef7
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/3772
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Removed the execute bit on all files in mainboard/amd/parmer/acpi
Change-Id: I85ffa66e0beb9c4bfe826b72968f7f633c224487
Signed-off-by: Kimarie Hoot <kimarie.hoot@se-eng.com>
Reviewed-on: http://review.coreboot.org/3807
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Change all PCI configuration accesses to MMIO in qemu-q35
emulation
To enable MMIO style access, add (move) explicit PCI IO config write
in the bootblock. As there is no northbridge/x/x/bootblock.c
file, a mainboard/x/x/bootblock.c file is added for this purpose.
Change-Id: I979efb3d9b2f359a9ccbd1b4f6c05f83bab43007
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3599
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Taking device_t as a parameter, this allows to alter the PCI config
access handlers. This is useful to add tracing of PCI config writes
for devices having problems to initialise correctly.
On older AMD platform PCI MMIO may not be able to fully configure all
PCI devices/nodes, while MMIO_SUPPORT_DEFAULT would be preferred due
to its atomic nature. So those can be forced to IO config instead.
Change-Id: I2162884185bbfe461b036caf737980b45a51e522
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3608
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
|
|
Refactor the structure to better support receive and another
set of endpoints over usbdebug.
Change-Id: Ib0f76afdf4e638363ff30c67010920142c58f250
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3726
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
|
|
The code to figure out how to set num_starts was
starting to get kludgy. It's a constant for a given
CPU; constants should be constant; make it a config variable.
This change includes an example of how to override it.
Build but not boot tested; drivers welcome.
Change-Id: Iddd906a707bb16251615c7b42f2bfb5a044379b4
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/3796
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-by: Bruce Griffith <Bruce.Griffith@se-eng.com>
|
