| Age | Commit message (Collapse) | Author |
|---|
|
This patch adds support for the Fintek F81866AD-I SuperIO,
which is very similar to the fintek/f81865f.
This code adds some fan control support, inspired by fintek/f71869ad.
Furthermore its possible to change the temp sensor type (thermistor or diode).
Datasheet: Name: F81866D/A-I, Release Date: Jan 2012, Version: V0.12P
Link: http://www.alldatasheet.com/datasheet-pdf/pdf/459085/FINTEK/F81866AD-I.html
Change-Id: Id2fc1119b37142f8101f71908e394ee69c45041d
Signed-off-by: Fabian Kunkel <fabi@adv.bruhnspace.com>
Reviewed-on: http://review.coreboot.org/10287
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Initialization for the Winbond W631GG6KB part using Synopsys
DDR uMCTL and DDR Phy.
This code adds a separate function for DDR3 initialization
and moves all the necessary defines in a separate header file.
The programming procedure that is executed at power up to bring
up the uMCTL, PHY and memories into a state where reads and
writes to the memory can be performed is the following:
1. uPCTL (Universal DDR protocol controller) initialization
The timining registers TOGCNT1U, TINIT, TOGCNT100N and TRSTH
needed for driving the memory power-up sequence are programmed
as a function of the internal timers clock frequency.
Organization (memory chip specific) values are set
(column/bank/row address width and number of ranks), together
with other static values (latency, timing, power up configuration).
All these values are static, provided by the datasheet,
being determined by the memory type, size and frequency.
2. PHY initialization
The PHY is programmed with datasheet provided values,
specifying the initialization values for it to send to the
external memory (timing parameters).
Also, delay lines (DLL) and strength of drive pads are
calibrated (based on external conditions: temperature,
voltage, noise) and locked. After that, the PHY goes
through a trainig process (also dependent on the
current conditions at boot time) to establish precise
timing configuration between the DDR clock and DQS (data strobe)
and between DQS and DQ (data).
3. Memory power up
4. Switch from configuration state to access state.
It was tested on Pistachio bring up board where DDR was initialized
properly and ramstage executed correctly
Change-Id: I3bcbce2044327a22fce09b184d85ee11228a6b2b
Signed-off-by: Ionela Voinescu <ionela.voinescu@imgtec.com>
Reviewed-on: http://review.coreboot.org/10529
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Switching from active windowing DQS gating scheme to
passive windowing mode resolves boot stability issues
on chips found to have memory corruption issues during
boot or memory tests.
It was tested on Pistachio bring up board where DDR is
initialized properly and ramstage executed correctly;
We have cycled units over 12,000 times with no boot errors.
This option was chosen over the alternative of using
passive windowing mode for DQS training and after switching
back to active mode, as this option was recommended by
Synopsys. Using the alternative would give different
timing values during training that were not longer accurate
during normal activity.
Change-Id: Ie604eddc0a9a982b2f89198f44deb88a01b7b322
Signed-off-by: Ionela Voinescu <ionela.voinescu@imgtec.com>
Reviewed-on: http://review.coreboot.org/10528
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Fix by checking the actual function return value (the search
address pointer), rather than the search length value (which isn't
guaranteed to be sane or useful).
Change-Id: I226c635ddbbc916b02494fcd97df27d141cc2c7f
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: http://review.coreboot.org/10516
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
|
|
Commit 899d13d (cbfs: new API and better program loading) broke
panther's lan init when no vpd.bin present from which to read
the MAC address. Fix this by checking the validity of the search
address pointer, rather than the search length.
Change-Id: I8c7ca410d8ce5c5d92242a21c4c2ff4c001a68bd
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: http://review.coreboot.org/10509
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
The proper log level for any given printk statement is up to the
interpretation of the developer. This results in console output with
somewhat inconsistent levels of verbosity. This patch clearly defines each
log level and its use case, hopefully resulting in less ambiguity for
developers.
The concern with this patch might be that it leaves a lot of preexisting
printk statements using a log level that is inconsistent with the
description. I think that *most* statements map to these extended
definitions very nicely. The most discrepancies are between debug and
spew, but I'm willing to say that 95% of statements with a level lower than
debug are correct by these definitions.
There was some discussion dating back to 2010 on the mailing list about
renaming these constants to lose the 'BIOS_' prefix and to consolidate
some of them into a single constant. I disagree that it is necessary
to merge any of them, I think they all have unique use cases. But I do
think that if you all agree with these definitions, it might be useful to
rename them to reflect their use cases.
I also will add that I believe removing BIOS_NEVER is a good idea. I do
not see the use case, and it's used in only 4 files.
Change-Id: I8aefdd9dee4cb4ad2fc78ee7133a93f8ddf0720b
Signed-off-by: Nicky Sielicki <nlsielicki@wisc.edu>
Reviewed-on: http://review.coreboot.org/10444
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins)
|
|
It's derived from EEPROM on Lenovo machines and not from user config
which is ignored.
Change-Id: I54fb76a3160e47cd36d33d2937c4bfaddcd36a69
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/7055
Tested-by: build bot (Jenkins)
Reviewed-by: Nicolas Reinecke <nr@das-labor.org>
|
|
This change adds cache management after loading stages.
Before jumping to a new stage we should flush the data
caches to memory and invalidate instruction cache.
After all segments are loaded CBFS cache is also
flushed.
With this change all stages of coreboot are now executed
successfully. This was tested on Pistachio bring up board,
also known as Urara.
Change-Id: I86e07432c21a803ef1cfc41b633c5df42b99de90
Signed-off-by: Ionela Voinescu <ionela.voinescu@imgtec.com>
Reviewed-on: http://review.coreboot.org/10456
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
The coreboot table address is passed as an argument when jumping
to payload.
With this change depthcharge is loaded and executed properly on urara.
Change-Id: I230d474a91b8d38aff070aa4aac623b6c8f0809c
Signed-off-by: Ionela Voinescu <ionela.voinescu@imgtec.com>
Reviewed-on: http://review.coreboot.org/10460
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Place included header files in alphabetical order.
Change-Id: Ice23178d1f07e2cb0178efbc7ce487d54bf3f708
Signed-off-by: Ionela Voinescu <ionela.voinescu@imgtec.com>
Reviewed-on: http://review.coreboot.org/10459
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Use cbmem_initialize_empty() after DDR configuration so that
cbmem is always initialized from scratch on each boot.
Change-Id: Ic9ca34867b26aab82cf3154280694b6fb61ee11f
Signed-off-by: Ionela Voinescu <ionela.voinescu@imgtec.com>
Reviewed-on: http://review.coreboot.org/10458
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins)
|
|
sata.asl and superio.asl are empty files. Remove them.
Change-Id: Icd3e990aa713281e46dcbd8e0847166c77656b1c
Signed-off-by: WANG Siyuan <wangsiyuanbuaa@gmail.com>
Signed-off-by: WANG Siyuan <SiYuan.Wang@amd.com>
Reviewed-on: http://review.coreboot.org/10505
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
The default ordering for the base kconfig entries has the CPU
directory coming before the SOC directory, which means that the
values in the CPU Kconfig take precedence.
The first visible consequence of this is that CONFIG_SMM_TSEG_SIZE
will be set to 0 on all SOC implementations.
BUG=chrome-os-partner:40635
BRANCH=none
TEST=build and boot on glados
Change-Id: Ifd56a2ceb73ab335a86126e48d35ff4c749990ac
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 0cddae37d3de1cbf3dd6afcf4a0707b7af9436fa
Original-Change-Id: I98e3bf249650b50667dde62b6be9c1bf587ad0b2
Original-Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/276189
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Original-Commit-Queue: Aaron Durbin <adurbin@chromium.org>
Original-Tested-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/10478
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Edward O'Callaghan <edward.ocallaghan@koparo.com>
|
|
BUG=none
BRANCH=none
TEST=Boot from mickey board
Change-Id: I6eadf52bddcf89011a112a8e5dee5e752556add9
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: e3c865f0bf8567c3183d7948a0f9e8361db70695
Original-Change-Id: I438527ee0870044f48b23a6842986e7cf166e191
Original-Signed-off-by: huang lin <hl@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/276290
Original-Reviewed-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/10477
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Edward O'Callaghan <edward.ocallaghan@koparo.com>
|
|
Copy the Peppy directory. No changes.
Change-Id: I3fa382eaa40f642df8bc09ab69be67cbe9f3671a
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-on: http://review.coreboot.org/10499
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Change-Id: I9b86ebec59ccb63db0e1ba61533d162507a22379
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/9320
Tested-by: build bot (Jenkins)
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Reviewed-by: Edward O'Callaghan <edward.ocallaghan@koparo.com>
|
|
Change-Id: I707802befe5b8aaafafc34b17cbdfe795777b6f6
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/10501
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
|
|
The type1 family setting from chromium was mis-merged into the
type2 function. Move it to the correct type1 function.
Bad commit: 51bdc4781635b99d89e6b7a414a2172be8cb690c
Change-Id: I72e6ef80bbf185a39fcf169c8247dc16462e6bc3
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-on: http://review.coreboot.org/10498
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
|
|
Change-Id: I8e8b6e7c123e641749c42a7c706176e285902bb5
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/10502
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
|
|
Change-Id: Ic3503938b996bbf31f1417923f019a7bc722b9fd
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/10429
Reviewed-by: Edward O'Callaghan <edward.ocallaghan@koparo.com>
Tested-by: build bot (Jenkins)
|
|
Change-Id: If2d48b84fe7bd7b144e96171e54067891e3c4e2e
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/9316
Tested-by: build bot (Jenkins)
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Change-Id: I8e78cbae132566b6ca27e0a68af2656364c82b8f
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/9332
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
The type of a resource is really an enumeration but our implementation
is as a bitmask. Compare all relevant bits and remove the shadowed
declarations of IORESOURCE bits.
Change-Id: I7f605d72ea702eb4fa6019ca1297f98d240c4f1a
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/8891
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
No board in the tree selects this and it looks like the implementation
was done at chipset level while it should be part of PCI subsystem.
When enabled, at least AMD K8 and f14, f15tn and f16kb fail build test.
Feature of placing prefetchable PCI memory above 4GB may not work if
there is any 32-bit only prefetchable PCI BARs in the system.
Change-Id: I40ded2c7d6d05f461423721aa5d78a78f9f9ce1e
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/8705
Tested-by: build bot (Jenkins)
Reviewed-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
On modern mainboards with multiple PCI-e devices and a single
graphics card the default MMIO hole size of 512M is inadequate,
leading to resource-hungry PCI-e devices (such as an external
graphics card) being assigned invalid MMIO ranges. This, in
turn, causes the entire PCI subsystem to become unavailable,
leading to a failure to boot.
TEST: Booted KGPE-D16 with NVIDIA 7300LE and verified proper
operation of PCI/PCI-e devices, including text mode VGA operation
via the add-on card and its VGA option ROM.
Change-Id: I8d25f4b19f2d0860644ab1ee002c15041437121f
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/10428
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Change-Id: I0302cbaeb45a55a4cfee94692eb7372f2b6b206d
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/10468
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
The MMIO hole start address was hardcoded on AMD Family 10h
systems. Use the MMCONF_BASE_ADDRESS Kconfig setting instead.
Change-Id: I204e904d96d14e99529fa5e524fd73e6ea256dc0
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: http://review.coreboot.org/10427
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Change-Id: Idd05a16bd9bd31438437ef229aa87f55da8489fb
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/10467
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
Change-Id: Iac390b565d709b11bc7a6631b11315994b6e2c3c
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/10466
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
Some patches landed that didn't introduce the Kconfig
options for additional firmware components. Add them.
Change-Id: I0a0b7f0291389d126a7c491f710618a278cfb5d7
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/10470
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
For console drivers which use udelay() we can deadlock
in the printk path on the spinlock. The reason is that
on the first call to udelay() from within a console driver
it will go back down the printk() path deadlocking oneself.
Just remove the printk() as it was asymmetric on romstage
vs ramstage.
Change-Id: I30fe7d6e5b4684f17d4f353c0816b64f9242de0a
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/10483
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins)
|
|
This change is necessary to support future additions to romstage.
Change-Id: Ibb69994847945c7adbafbf2bc677b33821df8146
Signed-off-by: Ionela Voinescu <ionela.voinescu@imgtec.com>
Reviewed-on: http://review.coreboot.org/10457
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Instead of having the chipset code make the approrpiate
calls at the appropriate places use the cbmem init hooks
to take the appropriate action. That way no chipset code
needs to be changed in order to support the external
stage cache.
Change-Id: If74e6155ae86646bde02b2e1b550ade92b8ba9bb
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/10481
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
It can be helpful to certain users of the cbmem init hooks
to know if recovery was done or not. Therefore, add this
as a parameter to the hooks.
Change-Id: I049fc191059cfdb8095986d3dc4eee9e25cf5452
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/10480
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Since commit 05294292 (device tree: track init times) there are two
lines printed for each init() call of a device, when
`HAVE_MONOTONIC_TIMER` is selected.
[…]
CPU_CLUSTER: 0 init 12708 usecs
DOMAIN: 0000 init
DOMAIN: 0000 init 1 usecs
PCI: 00:00.0 init
Northbridge init
PCI: 00:00.0 init 2 usecs
PCI: 00:01.0 init
PCI: 00:01.0 init 1 usecs
PCI: 00:01.1 init
PCI: 00:01.1 init 1 usecs
PCI: 00:11.0 init
PCI: 00:11.0 init 1 usecs
PCI: 00:14.0 init
PCI: 00:14.0 init 1 usecs
PCI: 00:14.3 init
SB800 - Late.c - lpc_init - Start.
RTC Init
RTC: coreboot checksum invalid
SB800 - Late.c - lpc_init - End.
[…]
Improve the output by changing the wording to.
%s init ...\n
init()
%s init finished in %ld usecs\n
Note, that `%s init ... done in %ld usecs` is not possible as the
function `init()` can also print messages.
Change-Id: I7132cd650911dba680f060d6073a5a09c879b24c
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/10455
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
CPU-side logic is unchanged for this range of CPUs as long as all of them
use TSEG (or ASEG, just needs to be consistent). So uplift 206ax code while
extracting southbridge and APIC code into separate functions.
Change-Id: Ib365681d1da8115922c557fddcc59afc156826da
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/10465
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
Squashed and adjusted two changes from chromium.git. Covers
CBMEM init for ROMTAGE and RAMSTAGE.
cbmem: Unify random on-CBMEM-init tasks under common CBMEM_INIT_HOOK() API
There are several use cases for performing a certain task when CBMEM is
first set up (usually to migrate some data into it that was previously
kept in BSS/SRAM/hammerspace), and unfortunately we handle each of them
differently: timestamp migration is called explicitly from
cbmem_initialize(), certain x86-chipset-specific tasks use the
CAR_MIGRATION() macro to register a hook, and the CBMEM console is
migrated through a direct call from romstage (on non-x86 and SandyBridge
boards).
This patch decouples the CAR_MIGRATION() hook mechanism from
cache-as-RAM and rechristens it to CBMEM_INIT_HOOK(), which is a clearer
description of what it really does. All of the above use cases are
ported to this new, consistent model, allowing us to have one less line
of boilerplate in non-CAR romstages.
BRANCH=None
BUG=None
TEST=Built and booted on Nyan_Blaze and Falco with and without
CONFIG_CBMEM_CONSOLE. Confirmed that 'cbmem -c' shows the full log after
boot (and the resume log after S3 resume on Falco). Compiled for Parrot,
Stout and Lumpy.
Original-Change-Id: I1681b372664f5a1f15c3733cbd32b9b11f55f8ea
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/232612
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
cbmem: Extend hooks to ramstage, fix timestamp synching
Commit 7dd5bbd71 (cbmem: Unify random on-CBMEM-init tasks under common
CBMEM_INIT_HOOK() API) inadvertently broke ramstage timestamps since
timestamp_sync() was no longer called there. Oops.
This patch fixes the issue by extending the CBMEM_INIT_HOOK() mechanism
to the cbmem_initialize() call in ramstage. The macro is split into
explicit ROMSTAGE_/RAMSTAGE_ versions to make the behavior as clear as
possible and prevent surprises (although just using a single macro and
relying on the Makefiles to link an object into all appropriate stages
would also work).
This allows us to get rid of the explicit cbmemc_reinit() in ramstage
(which I somehow accounted for in the last patch without realizing that
timestamps work exactly the same way...), and replace the older and less
flexible cbmem_arch_init() mechanism.
Also added a size assertion for the pre-RAM CBMEM console to memlayout
that could prevent a very unlikely buffer overflow I just noticed.
BRANCH=None
BUG=None
TEST=Booted on Pinky and Falco, confirmed that ramstage timestamps once
again show up. Compile-tested for Rambi and Samus.
Original-Change-Id: If907266c3f20dc3d599b5c968ea5b39fe5c00e9c
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/233533
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Change-Id: I1be89bafacfe85cba63426e2d91f5d8d4caa1800
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-on: http://review.coreboot.org/7878
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
The cbmem util needs the CBMEM_IDs and the strings for
reporting and shares the cbmem.h file with coreboot. Split out
the IDs so for a simpler sharing and no worries about overlap of
standard libraries and other things in the header that coreboot
requires, but the tool does not.
Change-Id: Iba760c5f99c5e9838ba9426e284b59f02bcc507a
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-on: http://review.coreboot.org/10430
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Taken from CrOS, including everything up to commit da4c33913.
Adapted to upstream.
Change-Id: I095e6726a220200ba17719fc05fcdc521da484e8
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Reviewed-on: http://review.coreboot.org/10432
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Change-Id: I78519b8f060b1ba81e8b9c7c345820180a14f2fe
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/10441
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Resync together, backporting a fix for the initialization of
8254 and 8259, as in commit 8d9a1bd5. Also fix a typo and
reduce out useless whitespace differences.
Change-Id: I9a9b1fb9083c5417a8d061f90a89074f2a601ddf
Signed-off-by: Edward O'Callaghan <edward.ocallaghan@koparo.com>
Reported-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/10453
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Used command line to remove empty lines at end of file:
find . -type f -exec sed -i -e :a -e '/^\n*$/{$d;N;};/\n$/ba' {} \;
Change-Id: I816ac9666b6dbb7c7e47843672f0d5cc499766a3
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: http://review.coreboot.org/10446
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Be consistent.
Change-Id: I13df06fbc86371bfcb4ddd809d07c9e7fb931018
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/10381
Tested-by: build bot (Jenkins)
Reviewed-by: Alexander Couzens <lynxis@fe80.eu>
|
|
The SOUTHBRIDGE_INTEL_FSP_I89XX symbols are never defined in any Kconfig
file or used anywhere in the existing coreboot tree. Removing them as
unnecessary. If the southbridge code ever gets uploaded, these can be
re-added at that point.
Change-Id: I36f9ca8e25e08ce154d10ea9d764a73095590244
Signed-off-by: Martin Roth <gaumless@gmail.com>
Reviewed-on: http://review.coreboot.org/10436
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Mimic vendor BIOS in switching off the led once coreboot has booted
successfully. Currently the led behavior is inconsistent. The led turns on
during poweron and stays on forever. When entering S3 and during S3 it
blinks and turns off after wake from S3. The behavior associated with S3
is the same under vendor BIOS and under coreboot. Switching off the led
before jumping to the payload makes the led behavior consistent within
coreboot before S3 and after wake from S3 and it makes the led behavior
consistent to vendor BIOS.
Change-Id: I0dec10b842b83dfc8054cd56d2750b724c4e8576
Signed-off-by: Axel Holewa <mono-for-coreboot@donderklumpen.de>
Reviewed-on: http://review.coreboot.org/10454
Tested-by: build bot (Jenkins)
Reviewed-by: Nicolas Reinecke <nr@das-labor.org>
|
|
Change the Kconfig board name symbol to uppercase to match
other symbols and to match the capitalization in the Kconfig
file where it's used in an expression.
Change-Id: I04ccb57cc15a6d7430f8d04136beb8384caa6c04
Signed-off-by: Martin Roth <gaumless@gmail.com>
Reviewed-on: http://review.coreboot.org/10440
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Edward O'Callaghan <edward.ocallaghan@koparo.com>
|
|
Cleaning up unused Kconfig symbols. These symbols are not used anywhere
in the coreboot tree as far as I can tell.
Change-Id: I4d0b9512a784083dd134a8706b3bd8eca2a3a909
Signed-off-by: Martin Roth <gaumless@gmail.com>
Reviewed-on: http://review.coreboot.org/10439
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
All other Kconfig locations start with tabs.
Change-Id: I0ee5f0b0b82f85c8ae58b3626f142f159554efb3
Signed-off-by: Martin Roth <gaumless@gmail.com>
Reviewed-on: http://review.coreboot.org/10438
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
generate_sata_ssdt_ports() generates ports based on sata enable map
Change-Id: Ie68e19c93f093d6c61634c4adfde484b88f28a77
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Reviewed-on: http://review.coreboot.org/9708
Tested-by: build bot (Jenkins)
Reviewed-by: Philipp Deppenwiese <zaolin@das-labor.org>
Reviewed-by: Peter Stuge <peter@stuge.se>
|
|
`device_t device` is missing as argument. Every device_op function
should have a `device_t device` argument.
Change-Id: I1ba4bfa0ac36a09a82b108249158c80c50f9f5fd
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Reviewed-on: http://review.coreboot.org/9599
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
`device_t device` is missing as argument. Every device_op function
should have a `device_t device` argument.
Change-Id: I7fca8c3fa15c1be672e50e4422d7ac8e4aaa1e36
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Reviewed-on: http://review.coreboot.org/9598
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
`device_t device` is missing as argument. Every device_op function
should have a `device_t device` argument.
Change-Id: I3fc8e0339fa46fe92cc39f7afa896ffd38c26c8d
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Reviewed-on: http://review.coreboot.org/9597
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
This simply copies veyron_brain to veyron_mickey and makes the
minimal set of changes (s/brain/mickey) to make it compile. The
follow-up patch will take into account board differences.
BUG=none
BRANCH=none
TEST="emerge-veyron_mickey coreboot" doesn't fail
Change-Id: I7d029b36d2fb865446490b896117ade632325a52
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 34f6b391290f99caf517d7e98c31c89dc57309be
Original-Change-Id: I03a2b80eb441384f363910467180479521765431
Original-Signed-off-by: David Hendricks <dhendrix@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/271360
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: http://review.coreboot.org/10408
Tested-by: build bot (Jenkins)
Reviewed-by: David Hendricks <dhendrix@chromium.org>
|
|
This simply copies veyron_brain to veyron_romy and makes the
minimal set of changes (s/brain/romy) to make it compile. The
follow-up patch will take into account board differences.
BUG=none
BRANCH=none
TEST="emerge-veyron_romy coreboot" doesn't fail
Change-Id: Ice1bc012bddd6c51b43944747e0df3ffa34207fa
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 0ab849178b69cf2323f126e503bd61080048240a
Original-Change-Id: I0516ce94fd3c6a38170fae221a070f503ccfaf0f
Original-Signed-off-by: David Hendricks <dhendrix@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/271345
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: http://review.coreboot.org/10407
Tested-by: build bot (Jenkins)
Reviewed-by: David Hendricks <dhendrix@chromium.org>
|
|
This patch adds a few bit counting functions that are commonly needed
for certain register calculations. We previously had a log2()
implementation already, but it was awkwardly split between some C code
that's only available in ramstage and an optimized x86-specific
implementation in pre-RAM that prevented other archs from pulling it
into earlier stages.
Using __builtin_clz() as the baseline allows GCC to inline optimized
assembly for most archs (including CLZ on ARM/ARM64 and BSR on x86), and
to perform constant-folding if possible. What was previously named log2f
on pre-RAM x86 is now ffs, since that's the standard name for that
operation and I honestly don't have the slightest idea how it could've
ever ended up being called log2f (which in POSIX is 'binary(2) LOGarithm
with Float result, whereas the Find First Set operation has no direct
correlation to logarithms that I know of). Make ffs result 0-based
instead of the POSIX standard's 1-based since that is consistent with
clz, log2 and the former log2f, and generally closer to what you want
for most applications (a value that can directly be used as a shift to
reach the found bit). Call it __ffs() instead of ffs() to avoid problems
when importing code, since that's what Linux uses for the 0-based
operation.
CQ-DEPEND=CL:273023
BRANCH=None
BUG=None
TEST=Built on Big, Falco, Jerry, Oak and Urara. Compared old and new
log2() and __ffs() results on Falco for a bunch of test values.
Change-Id: I599209b342059e17b3130621edb6b6bbeae26876
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 3701a16ae944ecff9c54fa9a50d28015690fcb2f
Original-Change-Id: I60f7cf893792508188fa04d088401a8bca4b4af6
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/273008
Original-Reviewed-by: Patrick Georgi <pgeorgi@chromium.org>
Reviewed-on: http://review.coreboot.org/10394
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Every Lenovo Thinkpad includes a Trusted Platform Module, so we can enable
it for the sandy-/ivybridge platforms.
Change-Id: Icda443ba88c2a49a0033014ce7710dd607fa15dc
Signed-off-by: Philipp Deppenwiese <zaolin@das-labor.org>
Reviewed-on: http://review.coreboot.org/10411
Tested-by: build bot (Jenkins)
Reviewed-by: Nicolas Reinecke <nr@das-labor.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Change-Id: I930f2beacdc95d0a7edd07db66a1c2e58bb2f3cd
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/8566
Tested-by: build bot (Jenkins)
Reviewed-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
|
|
Change-Id: Ice7cb89c19585cf725b6f73c33443050f8d65418
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/8565
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <edward.ocallaghan@koparo.com>
Reviewed-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
|
|
We can define is_sblink = (max == 0) as sblink is always the
very first chain we scan.
Change-Id: Ibd6b3ea23954ca919ae148604bca2495e9f8753b
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/8564
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <edward.ocallaghan@koparo.com>
Reviewed-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
|
|
Change-Id: I6041b666e6792cf97b8273ed54832d86af8ed23e
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/8563
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <edward.ocallaghan@koparo.com>
Reviewed-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
|
|
Change-Id: I1e935a6b848a59f7f2e58779bceea599032de9e3
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/8562
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <edward.ocallaghan@koparo.com>
Reviewed-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
|
|
Change-Id: I65fad1cfba95f0ee1ed3f7f7a57d874144da1e40
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/8561
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <edward.ocallaghan@koparo.com>
Reviewed-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
|
|
If SB_HT_CHAIN_ON_BUS0 is selected, HyperTransport chain for System Bus
is the first to scan and it will be assigned with bus number 0.
If HT_CHAIN_DISTRIBUTE is selected, each link will reserve a fixed range
of bus numbers instead of assigning consecutive numbers across all the links.
All fam10 have SB_HT_CHAIN_ON_BUS0 selected under northbridge.
Follow-up can easily drop this if we find this is dictated by architecture.
Change-Id: I8deddcb4c3fd679b6b27e2879d9dba3895c4dd6f
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/8366
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <edward.ocallaghan@koparo.com>
Reviewed-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
|
|
When we want to scan the HT chain to southbridge first, we
relocate it as the first item of dev->link_list of node 0.
Change-Id: Ic73ba43aadb3c5e0c8d4b82ed7d41094692ea37f
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/8560
Tested-by: build bot (Jenkins)
Reviewed-by: Nicolas Reinecke <nr@das-labor.org>
Reviewed-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
|
|
Define the default value under northbridge. The list of boards this
patchset touches will change to use SB_HT_CHAIN_ON_BUS0 with
follow-up patch.
Based on code analysis, these boards already scan system bus
as the first (active) HT chain, so it is placed as bus 0
even when this option was not explicitly selected.
Change-Id: I5a00d6372cb89151940aeee517ea613398825c78
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/8353
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <edward.ocallaghan@koparo.com>
Reviewed-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
|
|
Change-Id: I452a93af452073eeac4e6cb9bbc232dc59e911c1
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/8365
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <edward.ocallaghan@koparo.com>
Reviewed-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
|
|
Change-Id: I24ca1dce025e00064f9209affa27586292c7650e
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/8559
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <edward.ocallaghan@koparo.com>
Reviewed-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
|
|
Change-Id: Ic8fbafdfadbc4ef0896d93e61c8a54ce69297e07
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/8558
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <edward.ocallaghan@koparo.com>
Reviewed-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
|
|
Change-Id: I3b00e5e4e45089fbd7d0d6243d5e441bd8929c0b
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/8557
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <edward.ocallaghan@koparo.com>
Reviewed-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
|
|
Some cases of max==0xff wrapping around the 8-bit link->secondary
register remain to be solved.
Change-Id: I01e2ab6b2f23a03dbac49207ab584eccd1ca9b1f
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/8364
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <edward.ocallaghan@koparo.com>
Reviewed-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
|
|
Change-Id: I6bbd1b5eaa66a640e0a2e132c8d67f38f103caf5
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/8352
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <edward.ocallaghan@koparo.com>
Reviewed-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
|
|
Change-Id: I297de09dcf93511acece4441593ef958a390fddb
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/8362
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <edward.ocallaghan@koparo.com>
Reviewed-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
|
|
Change-Id: I41aeb80121f120641b65759c8502150ce89caa30
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/8556
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <edward.ocallaghan@koparo.com>
Reviewed-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
|
|
One PCI function may contain upto 4 links, further links must
be added to PCI function 4 on the same device.
There is no requirement that in dev->link_list the last element
would have the highest link->link_num.
Also fix off-by-one error when allocating for more links.
Change-Id: If7ebdd1ad52653d3757b5930bd0a83e2cf2fcac6
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/8555
Tested-by: build bot (Jenkins)
Reviewed-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
|
|
We test for it in xcompile and add it to CFLAGS.
Change-Id: I041a881b542bc55c1725af384f038da3356e3bb1
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/10426
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
The input/output value max is no longer used for tracking the
bus enumeration sequence, everything is handled in the context
of devicetree bus objects.
Change-Id: I545088bd8eaf205b1436d8c52d3bc7faf4cfb0f9
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/8541
Tested-by: build bot (Jenkins)
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Reviewed-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Change-Id: Ifd277992a69a4182e2fac92aaf746abe4fec2a1b
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/8540
Tested-by: build bot (Jenkins)
Reviewed-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Change-Id: Ib33d3363c8d42fa54ac07c11a7ab2bc7ee4ae8bf
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/8539
Tested-by: build bot (Jenkins)
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Parameter max is the cumulative number of PCI buses scanned on the
system so far. Use the property subordinate from the parent PCI bridge
device to keep track of the first available bus number instead of
passing that on the stack.
Change-Id: I1a884c98d50fa4f1eb2752e10b778aea8a7b090a
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/8537
Tested-by: build bot (Jenkins)
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Change-Id: I1766c92abe7a74326c49df74ba38930a502fcb5b
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/8536
Tested-by: build bot (Jenkins)
Reviewed-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
For the PCI root node, input parameter max==0 and output value
max is not relevant for operation.
Change-Id: I23adab24aa957c4d51d703098a9a40ed660b4e6c
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/8855
Tested-by: build bot (Jenkins)
Reviewed-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
|
|
The actual use of the parameter max is to keep track of PCI bus
number while recursively scanning PCI bridges or PCI-e rootports.
Neither CPU, SMBus, LPC or other static buses are involved in this
enumeration, but the way bridge operations were originally designed
forced to pass this argument thru unrelated functions.
Follow-up removes these once the function prototype gets fixed.
Change-Id: Idbc9c515a362c571a1798bb36972058b309c2774
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/8535
Tested-by: build bot (Jenkins)
Reviewed-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
|
|
Use of scan_static_bus() and tree traversals is somewhat convoluted.
Start cleaning this up by assigning each path type with separate
static scan_bus() function.
For ME, SMBus and LPC paths a bus cannot expose bridges, as those would
add to the number of encountered PCI buses.
Change-Id: I8bb11450516faad4fa33b8f69bce5b9978ec75e5
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/8534
Tested-by: build bot (Jenkins)
Reviewed-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
|
|
For amdfam10, (ht_c_index > 3) never evaluates true as the code
already has a return for this case above.
Change-Id: Ie90941671e1b2b4f42e2b1b0641ca59334fcf0f1
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/8688
Tested-by: build bot (Jenkins)
Reviewed-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Allows to remove parameter max from the call, it is not involved
with the unitid assignment.
Change-Id: I087622f4ff69474f0b27cfd8709106ab8ac4ca98
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/8687
Tested-by: build bot (Jenkins)
Reviewed-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Follow up for commit b890a12, some contributions brought
back a number of FSF addresses, so get rid of them again.
Change-Id: Idcd059f05523916f726b94931c2487ab028b7d72
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Reviewed-on: http://review.coreboot.org/10409
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Alexander Couzens <lynxis@fe80.eu>
|
|
cbfs_get_file_content was replaced with cbfs_boot_map_with_leak but
36f8d27ea9f741e184b76b5f42d7f777f207edc0 failed to get it into account.
Change-Id: I0c7840043b2ea6abaf8e70f4bf1a63c96aedebc1
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/10403
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins)
|
|
Change-Id: Ieb6f70f5b2863336bd6143b2dfbb1d67c4c26109
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/10323
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Makes it cleaner by putting AML into separate file rather than having
an array in C code.
Change-Id: Ia5d6b50ad9dabdb97ed05c837dc3ccc48b8f490f
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/10385
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
This should be an internal selectable variable rather than user-visible config.
Moreover the description is misleading.
This is a typical case of an option "Should it work?" where there is only one
right answer yet we still ask it.
Change-Id: Idc0ce2e1b9f89eddd034966cc877483d994ce0eb
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/10378
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
RELOCATABLE_MODULES controls inclusion of rmodule support but including it
without having anything that uses it is a pure waste of space. So instead
make RELOCATABLE_MODULES be selected exactly when there is something using it.
Change-Id: I377a955f0cd95b0f811b986df287864c3dc9f89a
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/10377
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
As there can be more than one source of firmware assets this
patch generalizes the notion of locating a particular asset.
struct asset is added along with some helper functions for
working on assets as a first class citizen.
Change-Id: I2ce575d1e5259aed4c34c3dcfd438abe9db1d7b9
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/10264
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins)
|
|
One can remove the struct buffer_area and use the region_device
embedded in the struct prog to represent the in-memory loaded
program. Do this by introducing a addrspace_32bit mem_region_device
that can have region_device operations performed on it. The
addrspace_32bit name was chosen to make it explicit that 32-bits
of address space is supported at the max.
Change-Id: Ifffa0ef301141de940e54581b5a7b6cd81311ead
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/10261
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins)
|
|
The api to mirror_payload() was changed, but as no board
in coreboot.org selected MIRROR_PAYLOAD_TO_RAM_BEFORE_LOADING
this issue was missed. Update to using the prog functions.
Change-Id: I4037f5dc6059c0707e1bf38eb1fa3d1bbb408e2a
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/10260
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins)
|
|
This reverts commit 701211a6e57a17ea861b4ad682dca7416fc9050e.
Change-Id: Ib3e573548bff5c17ab30cfab3d833a2065d689c9
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/10222
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins)
|
|
A new CBFS API is introduced to allow making CBFS access
easier for providing multiple CBFS sources. That is achieved
by decoupling the cbfs source from a CBFS file. A CBFS
source is described by a descriptor. It contains the necessary
properties for walking a CBFS to locate a file. The CBFS
file is then decoupled from the CBFS descriptor in that it's
no longer needed to access the contents of the file.
All of this is accomplished using the regions infrastructure
by repsenting CBFS sources and files as region_devices. Because
region_devices can be chained together forming subregions this
allows one to decouple a CBFS source from a file. This also allows
one to provide CBFS files that came from other sources for
payload and/or stage loading.
The program loading takes advantage of those very properties
by allowing multiple sources for locating a program. Because of
this we can reduce the overhead of loading programs because
it's all done in the common code paths. Only locating the
program is per source.
Change-Id: I339b84fce95f03d1dbb63a0f54a26be5eb07f7c8
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/9134
Tested-by: build bot (Jenkins)
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
The RPM initialization Acknowledge is cleared by writing 1
into bit-10 of the RPM_INT_ACK register.
The existing code got it wrong and is writing zero to that bit.
BRANCH=storm
BUG=chrome-os-partner:39231
TEST=with this patch and an RPM firmware update, an SP4 device
survived more than 1000 reboots in a row.
Change-Id: Ibba296ed0571ad9403a0c51c7f82f07f185b4e83
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 13b4a0f093ba652ad6bccdfc4b3686c0741c6fe7
Original-Change-Id: I39e6ea50e0f66b4af68bdb868dd4437c34bb4524
Original-Signed-off-by: Viswanath Kraleti <vkraleti@codeaurora.org>
Original-Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/266969
Original-Reviewed-by: Manoj Juneja <mjuneja@qti.qualcomm.com>
Reviewed-on: http://review.coreboot.org/10310
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
This patch provides support for TPM Infineon SLB9670 by adding its
device ID to the list.
BRANCH=None
BUG=chrome-os-partner:40640
TEST=Built and test SLB9670 on SKL U Reference board Fab 2
Change-Id: I2d26fc6c7d074881f2e6189e1325808544b7d26d
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 3c92884be75b631c302801e162292c245ed7bf5d
Original-Change-Id: I4607fc96f70175b2461b40ba61e7a821e187de40
Original-Signed-off-by: Wenkai Du <wenkai.du@intel.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/274053
Original-Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/10387
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
BRANCH=none
BUG=none
TEST=Booted on Oak and confirmed the output cacheable/non-cacheable
string is correct.
Change-Id: I062c1cc384b8cb9d07038399b1bc7ef47d992103
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 45552f95b55cd9fc81817e4ff02c78e885377065
Original-Change-Id: Ie52066dbefd2f54d0746792b89f0b57767811adb
Original-Signed-off-by: Jimmy Huang <jimmy.huang@mediatek.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/273994
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Original-Commit-Queue: Yidi Lin <yidi.lin@mediatek.com>
Original-Tested-by: Yidi Lin <yidi.lin@mediatek.com>
Reviewed-on: http://review.coreboot.org/10390
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
We have observed issues with enabling CONFIG_SMP and adding prints
before MMU is enabled on Tegra-based SoCs. This seems to be related
to the hardware assisted locks and the restrictions laid down by ARMv8
spec.
BUG=None
BRANCH=None
TEST=Boots to kernel prompt on smaug.
Change-Id: I29a52f5a972baf396c01faba3ae3e5ecd27563e9
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: f52ee4b5b2e9b7f54eee0d105cb7e17f9a7e1613
Original-Change-Id: I432895560f468903c7beef00e78b6d38275a619c
Original-Signed-off-by: Furquan Shaikh <furquan@google.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/272449
Original-Trybot-Ready: Furquan Shaikh <furquan@chromium.org>
Original-Tested-by: Furquan Shaikh <furquan@chromium.org>
Original-Reviewed-by: Furquan Shaikh <furquan@chromium.org>
Original-Commit-Queue: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: http://review.coreboot.org/10311
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
