| Age | Commit message (Collapse) | Author |
|---|
|
The CPU_SPECIFIC_OPTIONS already auto-selects the option. There's
no point in having a selectable option that is already selected.
There's already an option to select it within intel/common.
BUG=b:69614064
Change-Id: I0c7ce7d3f344668587a75ec683343559a4caea99
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/22906
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This code is not used at all any longer. Remove it.
BUG=b:69614064
Change-Id: I362280f876a335c0cc1c5691b86f5b27e3b5e2c9
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/22904
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Similar to Fizz, SataMode on nami should be set to AHCI. This change
fixes the configuration error done in 903472c
(mb/google/poppy/variants/nami: Add support for nami board).
BUG=b:70160119
Change-Id: Ia88b56ae6bd9121f8447f7c1a2f5a10990fb8ed5
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/22845
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
PCH_SPK_EN uses GPP_A23 and not GPP_A22. This change fixes the gpio
configuration error in the initial change 903472c
(mb/google/poppy/variants/nami: Add support for nami board).
BUG=b:70160119
Change-Id: I90d9c009369c53cfec47fe77356e181d5ecf7ad5
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/22844
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
This is mostly written from scratch and uses common spd ddr2 decode
functions.
This improves the following:
* This fixes incorrect CAS/Freq detection on DDR2;
* Fixes tRFC computation; tRFC == 78 is a valid timing which is
excluded and 0 ends up being used; (TESTED)
* Timings selection does not use loops;
* Removes ddr3 spd decode and is re-added in follow-up patches using
common ddr3 spd functions;
* Raminit would bail out if a dimm was unsupported, now in some cases it
just marks the dimm slot as empty;
* It dramatically reduces stack usage since it does not allocate 4
times 256 bytes to store full SPDs, amongs other unused things that
were stored in sysinfo;
* Reports when no dimms are present;
* Uses i2c block read to read SPD which is about 5 times faster than
bytewise read, with a fallback to smbus mode in case of failure,
which does seem to happen when the system is forcefully powered
off.
Change-Id: I760eeaa3bd4f2bc25a517ddb1b9533c971454071
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/19143
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
There's no sense in having the nvm abstraction in its own files. Put
that support directly into mrc_cache.c.
BUG=b:69614064
Change-Id: I0f1a801c6e1a8c35f70faf9e4318bdc45955047a
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/22883
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Implement the spi controller flash_protect() callback. No need to
have a global spi_flash_protect() once implemented.
BUG=b:69614064
Change-Id: I83f4310d8f78ba64727ba75eb75708d0cbaa7d53
Signed-off-by: Aaron Durbn <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/22882
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
In the fast spi support implement the callback for flash_protect().
This removes the need for having SOC_INTEL_COMMON_SPI_FLASH_PROTECT
Kconfig option as well spi_flash_get_fpr_info() and separate
spi_flash.[ch].
BUG=b:69614064
Change-Id: Iaf3b599a13a756262d3f36bae60de4f7fd00e7dc
Signed-off-by: Aaron Durbn <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/22881
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
|
|
Now that there is spi flash controller flash protection use that API
so the spi_flash_protect() API can be sunsetted since it was isolated
within the Intel code base.
BUG=b:69614064
Change-Id: I3908d0e3105b0ef9a0fbf4fc9426ac1be067f648
Signed-off-by: Aaron Durbn <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/22880
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Provide a spi controller specific protection callback to take
advantage of special spi flash controllers that have internal
protection registers built into the implementation. It's an
optional callback for spi controllers.
BUG=b:69614064
Change-Id: Ie50a6ce3bbda32620a25dd26fda1af944940bf28
Signed-off-by: Aaron Durbn <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/22879
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Export region_is_subregion() for determinig if a region is a child of
a parent region.
BUG=b:69614064
Change-Id: I6363fe4fdb33342f9d025a726ec7e17e87adf7e0
Signed-off-by: Aaron Durbn <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/22878
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Melfas kernel TS driver (melfas_mip4.c) will look up "ce"
GPIO during driver probe in ACPI _DSD.
But FW does not report "ce-gpios" but "enable-gpios" in _DSD.
Kernel will obtain GPIO from _CRS by index "0" without ID.
Melfas driver does not have separate condition
for MIT-410 so driver will set TS IC power off in probe.
FW now may need to add back "reset" pin in order to hack
this condition to let Melfas driver get "useless" GPIO
so TS IC power (VTSP) will be not off during driver probe by itself.
BUG=b:70149336
BRANCH=reef
TEST=emerge-snappy coreboot
Change-Id: Icf0451ff0c3df97cb2474e30542a2f46ba67d82a
Signed-off-by: Kevin Chiu <Kevin.Chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/22858
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
For Fizz, the default should be AHCI mode and not RAID
mode. Additionally, there is only one drive connector, so
attaching several drives for a RAID is hard.
BUG=b:70146894
Change-Id: I2a9aa2d6281a916c00ff4659a927f164ba0e0705
Signed-off-by: Kane Chen <kane.chen@intel.com>
Reviewed-on: https://review.coreboot.org/22837
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Remove Kconfig selected symbols that are duplicates in the same file.
Change-Id: I21a3814131f0c8e08732e826dd1bcbb677cbe0aa
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/22852
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Solve issues related to agesawrapper_call.h that came up at review
75dd50e233 (review 19724). This includes a hard coded table size and
2 macros: AGESAWRAPPER_PRE_CONSOLE() and AGESAWRAPPER().
Remove AGESAWRAPPER_PRE_CONSOLE(), and replace AGESAWRAPPER() calls with
the actual content of the macro.
BUG=b:62240989
TEST=Build kahlee with no errors, boot recording serial output and compare
to serial output from a build without these changes.
Change-Id: Ic51917d3961a51d4e725ff45b04f45eefe149855
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/22850
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add parameters to configure the integrated LAN via FSP. Since
this takes over a PCI CLKREQ# pin it needs to know which pin
it should use, and there are additional parameters for LTR and
a "K1 power save" feature.
This was tested on a KBL-R board with integrated LAN, verifying
that the device is functional under Linux with the e1000e driver.
Change-Id: Idb200cec90a3c0d4d9c914bae9983a3bcdafcd06
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/22856
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable the flashconsole driver in verstage so it can be used
with VBOOT enabled. This was tested on a VBOOT enabled system
using flashconsole to store the boot log.
Change-Id: Icd8a82dc962ece85b9fb3d2f5654369e821922eb
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/22855
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The opregion and fields are left over from when ACPI ASL code was
reading registers to determine the current setup. Now that the
ACPI device is generated with the correct information already this
code is not used at all and can be removed from the tree.
Change-Id: If89d90cc7105ed21e2134ac99224f6f8214cc8ad
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/22854
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Required so Windows knows if the storage is removable or not.
Change-Id: I0822d767ada872d55357ff229e47e08fbe778a36
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Reviewed-on: https://review.coreboot.org/22830
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The SOC_INTEL_COMMON_LPSS_I2C option is no longer used. Likewise, the
SOC_INTEL_COMMON_LPSS_I2C_DEBUG option which is dependent on
SOC_INTEL_COMMON_LPSS_I2C is by definition not used either. Therefore,
remove SOC_INTEL_COMMON_LPSS_I2C and change the name/dependency
for SOC_INTEL_COMMON_LPSS_I2C_DEBUG to SOC_INTEL_COMMON_BLOCK_I2C_DEBUG.
BUG=b:70232394
Change-Id: Icd77f028b77d8f642690a50be4ac2c50d9ef511a
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/22874
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Chris Ching <chingcodes@chromium.org>
|
|
Configure PRMRR to allocate 128MiB for SGX enclave memory and enable SGX
by default for GLKRVP platform.
Supported PRMRR size options:
0x02000000 - 32MiB
0x04000000 - 64MiB
0x08000000 - 128MiB
Change-Id: Ifa39df4a1da84bae49551a9626257bda0729752b
Signed-off-by: Pratik Prajapati <pratikkumar.v.prajapati@intel.com>
Reviewed-on: https://review.coreboot.org/21278
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
include helpers.h in chip.h so that devicetree can use macros from helpers.h
Change-Id: Idfdee637a9b66a30be31b9ed113e1a44e4032f34
Signed-off-by: Pratik Prajapati <pratikkumar.v.prajapati@intel.com>
Reviewed-on: https://review.coreboot.org/22774
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Cannonlake rvp serial log has been regressed with commit
I7eea910e065242689e87adac41281131674b39af(soc/intel/cannonlake:
Clean up UART code) because of common UART code is unable to
link all __weak function implementation from SoC uart.c due
to existing macro #define __SIMPLE_DEVICE__. Hence UART2 PCI
device resource programming is different than what it's been programmed
before.
This patch ensures UART2 PCI device resource enumeration is
working and we are getting serial log as expected.
Change-Id: I1f9df5e8d6490090ed65b06bdd0b40f824d36a8a
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/22862
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The overcurrent pins on kahlee weren't mapped correctly, causing
the USB-A port to stop working.
None of the EHCI only ports are used for external connectors, so all
of the overcurrent pins should go to the XHCI connections. This is
also true of the Grunt board.
On Grunt, this also means that we don't need OC3, as it doesn't map
to anything in the XHCI controller, as it's coming from an internal
hub.
BUG=b:70636233
TEST=Build & boot Kahlee, verify USB-A port is working again.
Change-Id: I53336a18a26bd9be27c7265fddbcd780632656bf
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/22860
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
Reviewed-by: Daniel Kurtz <djkurtz@google.com>
|
|
This patch enables the APLS touchpad in glkrvp platform.
TEST= Boot and test touchpad works.
Change-Id: I6f52f7db57ab52b5531e647bde2adbb78b40f76f
Signed-off-by: Shaunak Saha <shaunak.saha@intel.com>
Reviewed-on: https://review.coreboot.org/22627
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Remove "\t" from name strings in soc/amd/stoneyridge/southbridge.c array
irq_association[], and change the print string in soc/amd/common/amd_pci_util.c
that use the names from "%s" to "%-20s". This sets a fixed field of 20
characters for the string name, allowing for variable length to the names
(up to 20 characters), thus saving memory space used by the strings.
BUG=b:70344551
TEST=Build and boot, record output of irq routing and verify alignment.
Change-Id: I92dfac9b64932fb0cd3359abd4d1aac651535f1a
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/22785
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Add _PRW so that wake on WLAN feature works.
TEST=Boot to OS and check if WLAN device wakes host.
Change-Id: Id6689754d1c4100615e4e4ae5a7f9846f4bf785f
Signed-off-by: Bora Guvendik <bora.guvendik@intel.com>
Reviewed-on: https://review.coreboot.org/22611
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
|
|
This patch enables the APLS touchpad in cnl-y platform.
TEST= Boot and test touchpad works.
Change-Id: I461b9d119b1cac6c8c6cb9b096697f58e00d80ad
Signed-off-by: Shaunak Saha <shaunak.saha@intel.com>
Reviewed-on: https://review.coreboot.org/22369
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Stage addition to CBFS allows relocation to happen on the fly. Take
advantage of that by adding AGESA binary PI as a stage file so that
each instance will be relocated properly within CBFS. Without this
patch Chrome OS having multiple CBFS instances just redirects the
AGESA calls back into RO which is inappropriate.
BUG=b:65442265,b:68141063
TEST=Enabled AGESA_BINARY_PI_AS_STAGE and used ELF file. Booted and
noted each instance in Chrome OS build was relocated.
Change-Id: Ic0141bc6436a30f855148ff205f28ac9bce30043
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/22833
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
Currently, "tcc_offset" defined in devicetree is overwritten by
Intel FSP-S UPD "TccActivationOffset".
This patch will make "TccActivationOffset" refer to "tcc_offset".
TEST=check if MSR (0x1a2[29:24]) value is updated with "tcc_offset"
by iotools (rdmsr 0 0x1a2).
Change-Id: Ibc6f33bea19a1d59bc7e407815210942b38f0702
Signed-off-by: marxwang <marx.wang@intel.com>
Reviewed-on: https://review.coreboot.org/22818
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Intel common PCI driver is handle PCI subsystem ID
programming, hence no need to have an explicit soc
function to do the same.
TEST=PCI subsystem id is getting programming during
pci enumeration.
Change-Id: I3eb362ff1f3f6d5c81a0dbe854d8ecd59d5a0453
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/22770
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Intel common PCI driver is handle PCI subsystem ID
programming, hence no need to have an explicit soc
function to do the same.
TEST=PCI subsystem id is getting programming during
pci enumeration.
Change-Id: Iead57a286b26d532e578cfff99f412c23fd4c2fe
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/22769
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This patch ensures all Intel common PCI devices can
have subsystem ID programmed along with PCI resource
enabling (.enable_resources) as part of PCI enumeration
process.
TEST=Build and boot KBL/CNL/APL/GLK to ensure PCI
subsystem ID getting programmed.
Example:
Enabling resources...
PCI: 00:00.0 subsystem <- 8086/590c
PCI: 00:00.0 cmd <- 06
PCI: 00:02.0 subsystem <- 8086/591e
Change-Id: I46307b0db78c8864c85865bd0f3328d5141971be
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/22768
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This patch makes pci_dev_ops_pci structure global so that
caller can make use of this structure using extern.
Change-Id: I8de919aacccbc062475fb04f59ffb4957d3460b9
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/22814
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This change selects Kconfig option to disable native SD card
controller in ACPI tables, since it is not used on nami.
BUG=b:70160119
Change-Id: I6180c2b342c69e6a7c357f10b6297d67ea0211d7
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/22825
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Enable SATA port 0 to support SATA HDD.
BUG=b:69950854
BRANCH=None
TEST=emerge-fizz coreboot and boot on fizz dut
Change-Id: Ifbf5950151758286f8bff7250a68d9d0b3975ef9
Signed-off-by: David Wu <david_wu@quantatw.com>
Reviewed-on: https://review.coreboot.org/22815
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Shelley Chen <shchen@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
According to the PCH BIOS Spec (Doc#549921/Rev-2.3.4),
section 2.5.1.6, it is a requirement to program the same
value programmed in LPC "PCI offset 82h" into "PCR[DMI]+2774h"
to fully enable the Lpc IO enable decoding which is missing in
current source.
Without above changes, Skylake Saddlebrook platform with a
SIO does not boot.
Change-Id: Ief26e2718325b9d74ea0f83d47d2f917e0972173
Signed-off-by: praveen <praveenx.hodagatta.pranesh@intel.com>
Reviewed-on: https://review.coreboot.org/22819
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
MEM_ID SPD
0000 hynix-H5AN8G6NAFR-UHC
0001 hynix-H5ANAG6NAMR-UHC
0010 micron-MT40A51216JY-083E
0011 micron-MT40A1G16KNR-075E
0100 samsung-K4A8G165WB-BCRC
0101 samsung-K4AAG165WB-MCRC
BUG=b:69268926
TEST=build test
Change-Id: I1fd6335b3f8842252c42009a0a91a5b6ed3ea238
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/22748
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Ensure that soc/amd/common/blocks/include is the only #include
path for the AMD common code. This removes the duplicate soc/amd/common
include as well using the correct #include header in AGESA.c.
BUG=b:69262110
Change-Id: I50d85b28514fd905df415f0cc052b9924ee4e741
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/22828
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
Add INNOLUX P097PFG panel timing. According to Scalet schematic,
if GPIO3_D4 get low status, it will use INNOLUX P097PFG panel;
if GPIO3_D4 get high status, it will use KD097d04 panel.
Change-Id: I43fa5d859a9a529a84c58a953b37d03953ce648a
Signed-off-by: Lin Huang <hl@rock-chips.com>
Reviewed-on: https://review.coreboot.org/22780
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Move AGESA related source files in soc/amd/common under block directory.
Folder soc/amd/common/block subfolders should mimic soc/intel/common/block
subfolders (one subfolder per subject).
BUG=b:69262110
TEST=Build with no error gardenia and kahlee (no code change, just folder
reorg).
Change-Id: I497cdefe64e8dff00aaff7153c4ffa9c57c9acf8
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/22792
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Move AGESA related headers in soc/amd/common to
soc/amd/common/block/include/amdblocks.
BUG=b:69262110
TEST=Build with no error gardenia and kahlee (no code change, headers moved).
Change-Id: I5d3064625ddf8caaf370aabaf93165c6817f1ca0
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/22772
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
This fixes some bitwise logic errors that caused the coarse offset not
to be programmed.
This fixes a regression introduced by 6d7a8c
"nb/intel/x4x/raminit: Rework receive enable calibration"
where the coarse offset doesn't get programmed anymore.
TESTED on Foxconn g41s-k on a DIMM where the final DQS receive enable
delays are close but above and below the edge of a coarse delay setting.
Change-Id: I41869815f782a2ea1178bdea006e3a7587441323
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/22816
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Also adds a comment in the code to clarify what this array is about.
Change-Id: I04b185a5dbd7a7ccb039820f19d2cb549b9a2eac
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/22809
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
This is required at least on Skylake to be able to configure text mode.
3rdparty/libgfxinit is also updated by the single commit:
42fb2d065d gma: Add procedure to power up legacy VGA block
Change-Id: I2fe144765e2b2acd9f6b76db375cae5b8feb5489
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/21386
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
This change provides implementation of variant_memory_params for
nami. Since it uses DDR4 memory, DQ-DQS mapping table is not
required. Also, Rcomp resistor values are provided based on SDP v/s
DDP memory.
BUG=b:70188937
Change-Id: Ic1d0cfdb7d8b02fa0be0a4c54b20057a4c2fc3ce
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/22779
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This change updates scl_lcnt value for I2C5 to bring the bus frequency
closer to 400kHz.
BUG=b:65062416
TEST=Verified that I2C5 frequency is between 389-396kHz.
Change-Id: Ibaccab0c797174332633cb75e30d18ff5af76a43
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/22788
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
The following files need to be moved: amd_pci_util.c, amd_pci_util.h and
spi.c. The remaining files are AGESA related and will be part of a separate
issue/commit.
BUG=b:62240201
TEST=Build with no error gardenia and kahlee (no code change, just folder
reorg).
Change-Id: I3f965afa21124d4874d3b7bfe0f404a58b070e23
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/22765
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
D0 stepping with CPUID 0x60663 need to be added in coreboot.
TEST=Boot up with D0 stepping processor
Change-Id: I3b0f2616843367d2bfbee1b5bf75772b9e83e931
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/22676
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Due to a schematic error, our code was written to configure more I2S0
pins than are actually used. We're also pinmuxing the whole bank of pins
over to the I2S controller even though we don't need them all. Restrict
the GPIO initialization and pinmuxing to the pins we really need so the
other ones can be correctly used as SKU ID pins on Scarlet.
Also, move the "audio" IO voltage domain selection to the other such
selections in the bootblock, since that covers two whole banks of GPIOs
and there's no guarantee that they're all used for audio (and thus not
needed before ramstage).
BUG=b:69373077
TEST=Booted Scarlet, confirmed correct SKU ID (7) was detected on rev2.
Change-Id: I9314617e725fe83d254984529f269d4442e736f1
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/22791
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: David Schneider <dnschneid@chromium.org>
|
|
These pins need to be pull-ups. I forgot.
BUG=b:69373077
Change-Id: I9314617e01d35898254984529f269d4442e736f1
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/22775
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Make lint-stable was giving an error on this.
Change-Id: I06d11d86151f683b82b6df537e3de8c52d33e8b4
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/22811
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Youness Alaoui <snifikino@gmail.com>
|
|
BUG=b:70432544
TEST=Build & boot kahlee. Look at timestamps.
Change-Id: I8209160f8e23ab77987f8e515c7b00d94f68c8be
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/22798
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
BUG=b:70432544
TEST=Build & boot kahlee. Look at timestamps.
Change-Id: I3bf691a0fb1f5c09e7b6c9965c9e506393ec31f6
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/22797
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Adds Maxim98357a support for Nautilus using the generic driver
in drivers/generic/max98357
BUG=b:68686020
TEST=With entire merged audio should be enabled on max98357
speaker codec.
Change-Id: I958bf7c1395259b3e3fb30332882fd51a48dc0cc
Signed-off-by: Naveen Manohar <naveen.m@intel.com>
Reviewed-on: https://review.coreboot.org/22458
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Nautilus board uses max989357a speaker codec and 4CH DMIC.
Select the appropriate NHLT blob to be packaged in CBFS.
Also generate the required ACPI NHLT table for codec
and the supported topology in nautilus.
BUG=b:68686020
TEST=With the required driver support in kernel verify that
the Audio plays on Speaker and captures on 4CH DMIC
Change-Id: Ie90af02e0935029f53f9020bd78027b6eb31a187
Signed-off-by: Naveen Manohar <naveen.m@intel.com>
Reviewed-on: https://review.coreboot.org/22457
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Removes rs780_before_pci_init() since it was a no-op anyway.
Removes get_nb_rev() since this function is provided via a macro in
the header.
This Makes a lot of function non-static since the header has
prototypes for these.
Change-Id: I8933516771d959583bbd59a5c1beee3e30a7004f
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/20297
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Change-Id: Ib1b761fc417f1bb000f408d3bed5e8666963f51d
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/22603
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Instead of repeatedly walking cbfs for the AGESA blob and parsing it
cache the resulting dispatcher value. There's only one dispatcher table
so use it. The resulting change is that this work is done one time per
stage.
BUG=b:70401101
TEST=Booted and noted only one lookup per stage.
Change-Id: Iaa4aecc384108d66d7c68fc5fb9ac1c3f40da905
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/22789
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
|
|
- Change soc/amd/stoneyridge/Kconfig to set BOOT_DEVICE_SUPPORTS_WRITES
BUG=b:65485690
TEST=Build & boot kahlee.
Change-Id: I595a27ac27daa42c2499de1a343bc30be9a89fa6
Signed-off-by: John E. Kabat Jr <john.kabat@scarletltd.com>
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/22636
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Add the spi header for spi function prototypes. Fixes spi.c build
error for the missing header.
Change-Id: I0dbb5bf84cc3462a7aa58a5531d6b8b8bc8ca4df
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/22793
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Change-Id: Ie83c800a0bcd12fa501c91a1c2b1ee756de9d732
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/21675
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
This introduces a Kconfig option to include common Intel SPI code.
Change-Id: I970408e5656c0e8812b8609e2cc10d0bc8d8f6f2
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/21674
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
Add proper variants gpio.h in dsdt.asl where the GPE_EC_WAKE and
EC_SCI_GPI is defined.
Change-Id: Ideb6dd4d0ac496a81721cd883865218cb19583d9
Signed-off-by: Shaunak Saha <shaunak.saha@intel.com>
Reviewed-on: https://review.coreboot.org/22760
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Adapted from Chromium commit d6655eb
[Skylake: create UPD Interface for acoustic noise tuning]
Add FSP 1.1 params needed for acoustic mitigation on google/caroline
(to be upstreamed in a subsequent commit).
TEST: build/boot google/caroline
Change-Id: Ifb36ecef8c1735c63a5322d952929e9c34cddfb9
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/22524
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Corrects MBSC/MBFS programming when initializing DRAM on boards with both
3 and 4 DIMM slots.
Reformats comments to current coreboot standards.
Drops some romcc "optimizations" no longer necessary.
Boot tested on asus/p2b-ls, where it fixes a memory related hang after
SeaBIOS resets the board with nothing to boot from.
Change-Id: Ib8c21489338643e13f69bd58008d14733796d4d0
Signed-off-by: Keith Hui <buurin@gmail.com>
Reviewed-on: https://review.coreboot.org/22687
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Due to review 20b8c821e4 being abandoned and review 376dc82dca being
merged, file amd_pci_int_types.h became orphaned (not included by any
file), while an array similar to intr_types[] (but that also includes
the associated register index) was created in southbridge.c replacing
the original array functionality.
Remove the header amd_pci_int_types.h from the repository.
BUG=b:70328428
TEST=Build kahlee with no errors.
Change-Id: I53a9d7ebb27edbc4e136c9b17f5c709930e35223
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/22778
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
In the original Chromium source, PcdMemorySpdPtr is only set for
cyan, but none of the other Braswell variants. When upstreamed,
it was left set for all boards as it didn't appear to be problematic.
In wider testing, I came across one reks board for which it caused
FSP memory init to fail, so restricting the parameter to cyan only
as it was originally.
TEST: build/boot google/reks with Micron EDF8132A3MA-JD-F RAM,
observe board now successfully boots where it did not previously.
Change-Id: Iacfbd4bc89fa04717baf85704181d346bca2ed2f
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/22782
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Clean up and move UART related code under a single uart.c file.
Change-Id: I7eea910e065242689e87adac41281131674b39af
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-on: https://review.coreboot.org/22771
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
|
|
- The touchscreen interrupt was moved from the GPIO 3, as originally
suggested to GPIO 11. This changes the gevent from 2 to 18.
- Add EMMC reset on GPIO 93.
- Add EMMC bridge PCIe reset on GPIO 40.
- Set device enables to high.
- Remove extra SCI comment from GPIO 130.
- Set individual device PCIe reset pins to high.
- Enable global PCIe reset on GPIO 26.
- Mark LPC_CLK1 as unused.
- Update net names based on latest schematics.
- Set Direction and level/edge correctly for SCIs/SMIs.
- Remove SCI for pen detect.
- Add comments.
BUG=b:70234300, b:69681660, b:69305596
TEST=build grunt
Change-Id: Ib591e4278ed23d0963ecb19ad9c326498b4c7796
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/22751
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
- Grunt moved the EMMC chip to port 2, where Kahlee had the SD reader on
PCIe port 1, so move the OemCustomize file into the variant directory.
- Add comments in baseboard version so it's easier to understand.
- Update reset pins, put the definitions in gpio.h
BUG=b:70255003
TEST=Build and boot Kahlee. Build Grunt.
Change-Id: I78ec72e9d6fd52b8ac75e7187bd01ee7ddc3ba2a
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/22750
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
|
|
On GLK EC does not support temperature reads and does not control
the fans anymore, OS is responsible fan control through EC.
This hack enables running of the fan for boards without External EC.
Change-Id: I361e53d4fd53678f3abb8fe9862071aec6e149a7
Signed-off-by: Srinidhi N Kaushik <srinidhi.n.kaushik@intel.com>
Reviewed-on: https://review.coreboot.org/22235
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
|
|
Update FSP header files to match FSP v69_51.
UPD updates in FSP v69_51 are:
- SGX Epoch
- Sub/System Vendor ID
- Remove deprecated UPD
Change-Id: I7298615a6e051061b948814a1cd9cbd42f6574b5
Signed-off-by: Ravi Sarawadi <ravishankar.sarawadi@intel.com>
Reviewed-on: https://review.coreboot.org/22391
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
This patch does not put CLKRUN in IOSTANDBY.
Change-Id: I7fedd729d3bb66c2b52a63166e461f8760457721
Signed-off-by: Shaunak Saha <shaunak.saha@intel.com>
Reviewed-on: https://review.coreboot.org/22292
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Add CNVi GPE in _PRW for wake on WLAN from S3
Change-Id: I682c76b9c5c524face7b540ecb185a3d7b4b2da3
Signed-off-by: Hannah Williams <hannah.williams@intel.com>
Reviewed-on: https://review.coreboot.org/22639
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Add GPE in _PRW for wake from S3 for HD-audio controller
Change-Id: I6ad289be8c58e48ad0ec9d2ee0894fe16b8f2e1c
Signed-off-by: Hannah Williams <hannah.williams@intel.com>
Reviewed-on: https://review.coreboot.org/22637
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
This patch makes coreboot set the max current and voltage for barrel jack
adapters.
BUG=b:64442692
BRANCH=none
TEST=Boot Fizz. Use chgsup console command to verify the max current and
voltage are set as expected.
Change-Id: Ifebee09096e0935cc7d3e53920a251b0496d3c55
Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org>
Reviewed-on: https://review.coreboot.org/22623
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch adds EC_CMD_OVERRIDE_DEDICATED_CHARGER_LIMIT, which
overrides the max input current and voltage when a barrel jack
adapter supplies power.
BUG=b:64442692
BRANCH=none
TEST=Boot Fizz. Use chgsup console command to verify the max
current and voltage are set as expected.
Change-Id: I8c6fc54e519ce13e3db82ee2cecaa96c6eb42d8a
Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org>
Reviewed-on: https://review.coreboot.org/22624
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This patch makes AP send EC_REBOOT_HIBERNATE_CLEAR_AP_OFF, which makes
EC clear AP_OFF flag then hibernate.
This is needed to make Chromebox boot when cr50 toggles the EC's reset
line after TURN_UPDATE_ON command.
BUG=b:69721737
BRANCH=none
CQ-DEPEND=CL:802632
TEST=Verify Fizz reboot after cr50 update.
Change-Id: I5f590286393ac21382cab64afdccae92d3fc14ba
Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org>
Reviewed-on: https://review.coreboot.org/22657
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
As noted on linux-pci, we have a weird way to handling "value" and
"scale" fields that are supposed to contain numerical values: we encode
them as a bitfield.
Instead define the two fields (offset and mask) and use numbers.
Another issue, not fixed in this CL, is that we write hard-coded values
while these fields really need to contain the max() of acceptable delays
of the downstream devices. That way the controller can decide whether or
not to enter a deeper power management state. It's noted as a TODO.
Change-Id: I895b9fe2ee438d3958c2d787e70a84d73eaa49d2
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Found-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-on: https://review.coreboot.org/22740
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Allow overriding specific GPIOs by SKU ID. Override two GPIO settings
for nasher to save the power consumption when the system in S0ix.
Change as below:
AVS_DMIC_CLK_A1: IGNORE -> Tx1RXDCRx0.
AVS_DMIC_CLK_B1: IGNORE -> Tx1RXDCRx0.
BUG=b:69025557
BRANCH=master
TEST=compile/verify the power consumption change from ~150mW to ~100mW
on clamshell SKU and from ~200mW to ~100mW for convertible SKU.
Change-Id: I9e0674f206426fddb3947273754774b310106334
Signed-off-by: Chris Wang <chriswang@ami.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/22752
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
This patch ensures that all required information for pch/mch/igd
deviceid and revision are available in single stage and makes
use of local references.
TEST=Build and boot cannonlake_rvp to get PCH information as below
PCH: device id xxxx (rev xx) is Cannonlake-Y Premium
Change-Id: I420e94043145e8a5adcf8bb51239657891915d84
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/22767
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This patch ensures that all required information for
pch/mch/igd deviceid and revision available in single
stage and make use of local references.
TEST=Build and boot soraka/eve
Change-Id: I6f7f219536831210750a486ee3b3308d6f285451
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/22756
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
PCI resources MMIO space/bus master enabling is handled inside
pch_dev_enable_resources() from common device code. Hence
no need to have an explicit soc function to do the same.
TEST=lspci from kernel console shows same pci device list
without and without this patch.
Change-Id: I005e486dd435e9c61ae3f5dfe3ff0e8f688d16e1
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/22755
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
We only need the apu firmware in the RO region when building
for ChromeOS. Adding it to the RW regions is a waste of space.
BUG=b:70027919
TEST=Build kahlee and use cbfstool to check for "apu/amdfw" sections.
Change-Id: Ieafe4a5ec4a5e3177e4e23fcf42afa2626a0b19f
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/22766
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Skip LPC related gpio configuration if eSPI config option
is selected.
Change-Id: I15c5f769f36a1801217b1e3650379c7b181d814f
Signed-off-by: Bora Guvendik <bora.guvendik@intel.com>
Reviewed-on: https://review.coreboot.org/22757
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
All preparation done, early_setup.c now useless. Delete early_setup.c,
BUG=b:64033893
TEST=None.
Change-Id: Ibe75a2d5cc46641e9d0af462a8a0ba5bb7a0f9c3
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/22569
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
With the old timing, the hblank time isn't large enough,
it may cause display artifacts. So fix it.
BUG=b:70160653
TEST=panel work on Scarlet rev2 board
Change-Id: Ib061f5e215611d20f59e3f24cfe3c7fbc507ebed
Signed-off-by: Lin Huang <hl@rock-chips.com>
Reviewed-on: https://review.coreboot.org/22746
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
This logical device is disabled in OEM BIOS. Disable here to match,
since its support is currently incomplete anyway.
Change-Id: I5c07136ec6a14a8ee8cb68537a2663b78fc0fa20
Signed-off-by: Keith Hui <buurin@gmail.com>
Reviewed-on: https://review.coreboot.org/22145
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Updates ACPI tables with work done for asus/p2b-ls, including super I/O
related declarations.
Change-Id: Id2420da4ab04aa5f59ac0aa237d21477a03b826e
Signed-off-by: Keith Hui <buurin@gmail.com>
Reviewed-on: https://review.coreboot.org/22473
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Add ACPI tables support that will be needed for soft-off and S3 resume in the future.
Boot tested for soft-off.
Change-Id: I28b559406bd53efc555dcbb8282dfe2bd6d1af87
Signed-off-by: Keith Hui <buurin@gmail.com>
Reviewed-on: https://review.coreboot.org/21672
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Rework ACPI tables based on a mix of previous work on asus/p2b,
other boards in tree with better ACPI support, and OEM BIOS.
To be pulled in by DSDTs of mainboards using this southbridge.
Disable on-the-fly generation of mainboard _CRS node. It is not working
as it should and causes runtime errors when booting Linux. This node
to be included in mainboard DSDTs in followup patches.
Change-Id: Idda424de7859a36e4cac168d5469f9365a6ad421
Signed-off-by: Keith Hui <buurin@gmail.com>
Reviewed-on: https://review.coreboot.org/21671
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
In preparation to deleting early_setup,c, change early_ec_init() to use new
southbridge.c function sb_set_wideio_range and remove <#ifdef __PRE_RAM__>.
BUG=b:64033893
TEST=Build, boot and check serial output, search for "Covered by wideIO xx",
which should match earlier message "Range assigned to wide IO xx" generated
within modified early_ec_init().
Change-Id: Iaea17f4f636aab6bd8b05b1b3bed53a677164e74
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/22591
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Use the new wide IO functions from southbridge.c to simplify code in
functions set_child_resource and lpc_enable_childrens_resources.
BUG=b:64033893
TEST=Boot to OS, check serial output against previously recorded serial
output from an image without all 5 related changes.
Change-Id: I8533e8ff766df8a8261298559aace7666487826d
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/22574
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Create new generic wide IO functions in southbridge.c. These new
functions must be usable by kahlee/ec.c and amd/stoneyridge/lpc.c.
BUG=b:64033893
TEST=Just build at this stage, full boot to OS and verify serial output
at related change 14fdd03a83. Some extra outputs for testing removed
when code was committed.
Change-Id: Icd0841a1959f3e109b3c35fa35bb4b3c44099dc3
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/22590
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
This change adds variant nami derived from baseboard poppy.
BUG=b:70160119
Change-Id: Ic6795d49d3e6e98a32f4af0b621e8bb463041412
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/22703
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This change updates memory SPD handling code in baseboard poppy to
allow variants to define either LPDDR3 or DDR4 memory types. In
addition to that, it also updates the function to print SPD info
considering offsets that might be different across the two memory
types.
BUG=b:70188937
Change-Id: Iefad01719c62264fb0d7e987904e77647d6026c2
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/22745
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Until now, nautilus was using the DQ-DQS mappings provided by the
baseboard. However, based on schematics, these values are not
correct. This change adds DQ-DQS mapping tables for nautilus.
BUG=b:70188533
Change-Id: Ife6ba19b8fe8873ab8cca977ca8f34a4d86e8e6e
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/22706
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: shkim <sh_.kim@samsung.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Add config option to enable eSPI
TEST=Boot to OS
Change-Id: Ib4634690fe4fdb902fc0bc074a3b66b91921ddd5
Signed-off-by: Bora Guvendik <bora.guvendik@intel.com>
Reviewed-on: https://review.coreboot.org/22320
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Hannah Williams <hannah.williams@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
|
|
Clean up and move UART related code under a single uart.c file.
Change-Id: I9a30258ba43ee5920f585c1bd06bc25773778ec4
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-on: https://review.coreboot.org/22754
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
|
