| Age | Commit message (Collapse) | Author |
|---|
|
In Scarlet pwm regulatoror minimum value and maximum value differs from
other board variants, Correct it so we can get the right voltage.
Change-Id: I1f722eabb697b3438d9f4aa29c205b0161eb442a
Signed-off-by: Lin Huang <hl@rock-chips.com>
Reviewed-on: https://review.coreboot.org/20831
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
in Scarlet the Sdcard control gpio differs from other
board variants, So set the GPIO to high on Scarlet.
Change-Id: I5fa19b212a716213462eea58b6242392d32a2c5c
Signed-off-by: Lin Huang <hl@rock-chips.com>
Reviewed-on: https://review.coreboot.org/20803
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Scarlet gpio4cd use 1.8V powerdomain, let's make a
correct register setting, otherwise even the uart
does not work.
Change-Id: Ib5a8b2a4d92502fb829688d0a3e1b645d53cd7fc
Signed-off-by: Lin Huang <hl@rock-chips.com>
Reviewed-on: https://review.coreboot.org/20802
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
The array of CMOS values that was passed into the read routine was
never getting updated. GCC 7.1 gives a warning on this:
error: may be used uninitialized in this function
Change-Id: I2f7c9b6455761a38598467b001efb0603fd14c32
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/20700
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Add the Google mainboard GPIOs to the ACPI table.
Change-Id: I9b5952ed3934b938cb50650890a7b434e6306fd1
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/20313
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
The EC KBC controller was not initialized, so the EC wouldn't put
keys in the output buffer. With nothing in the buffer, vboot didn't
try to boot the USB stick. Add the driver to setup the KBC called by
EC init.
BUG=b:62066405
BRANCH=none
TEST=Boot Kahlee with USB stick and CTRL+U boots the stick.
Change-Id: If9346fda558e802536c7de38da5b21fd25320e40
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/20480
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Move mainboard_ec_init out of mainboard enable to the more
appropriate mainboard init phase.
Change-Id: Ieabcecf70e4de0b42fc639d031755b6d0b66f08a
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/20312
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
A mainboard may access GPIO in romstage.
Change-Id: Id380c6570943ce2a0bf6112d62cc91aeae283fcf
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/20310
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Change-Id: Ia6c7357ba0c581dc46d173f462efce181847a4e1
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/20526
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Move the mainboard MADT tables to generic soc ACPI code.
Change-Id: I49fb55b1315da8fe65421b43fc4312ed588d5ecb
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/20277
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add ACPI support for the Google EC, which requires GNVS support
for passing information from the EC to firmware and OS.
Change-Id: I0a308bcd608a135cc9633273a05527f020b60743
Signed-off-by: Marc Jones <marc.jones@scarletltd.com>
Reviewed-on: https://review.coreboot.org/20276
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Add ACPI asl for global non-volatile storage (GNVS).
Change-Id: I9ecab92181bfe60e7b6c6e91ffb9fa843345352f
Signed-off-by: Marc Jones <marc.jones@scarletltd.com>
Reviewed-on: https://review.coreboot.org/20275
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Set up the TPM decode to SPI prior to verstage.
Enable LPC TPM and remove the mock data.
Note, Kahlee TPM is on SPI, but decoded by the LPC block.
BRANCH=none
BUG=b:62103024
TEST=coreboot and Depthcharge reports TPM found.
Change-Id: Iab92259ebeaa40937309fad05cc45d9ca6d41357
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/19848
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Store VBOOT NV data in CMOS. This allows VBOOT to save flags and data
to be used in multiple stages and depthcharge. Fixes developer mode
USB boot.
Change-Id: I50b45e687a1a1c71838bcc390212b28d7e634a19
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/19847
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Set DDI port 2 type to Display Port.
Change-Id: Idc5e57e01d4f0073ac50533c1b04a95bcae67473
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/19846
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Inform AGESA to setup an I2S codec instead of an Azalia codec.
This is step one for audio to work. ASL to connect the
driver and the hardware is in a follow-on patch.
Change-Id: I7ece5d8c317ddc76e0e6b2a005256bc384fe51e2
Signed-off-by: Marc Jones <marc.jones@scarletltd.com>
Reviewed-on: https://review.coreboot.org/19841
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
The save_timestamp_to_cmos code was used at Sage before the early
cbmem was available. Update it to use the standard timestamp calls,
based on the rangeley implementation.
Change-Id: I9a3a6609bdc8d03c4b86951daa1cafddd9c1332e
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/20564
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Sync map_oprom_vendev() and autoport with the list of PCI ids in the
`gma.c` driver, remove one obsolete Kconfig default override.
Change-Id: I12f24f415b695c516fbb947114e09c873af2e439
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/20814
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
All affected boards did the same USE_NATIVE_RAMINIT distinction or
actually selected USE_NATIVE_RAMINIT. Also update autoport.
Change-Id: I924c43cec1e36e84db40e4b8e1dd0e05cad2b978
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/20813
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Alexander Couzens <lynxis@fe80.eu>
|
|
For x86, we place the .id section at 4GiB - CONFIG_ID_SECTION_OFFSET.
To take effect, we have to guard the conflicting default placement in
`program.ld`. Also, as we only include the .id section into the boot-
block, guard it by ENV_BOOTBLOCK too.
Change-Id: Idc7cbd670ce4f75b7790ff8d95578683e355ba7e
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/20810
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
|
|
Change-Id: I8d9097100eee68a67091342161d169929c1a74dd
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/20696
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Never reached and actual code was already wiped out.
Change-Id: Ic17cbc56e83d23e228e23578357843ac9cd77eda
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/20623
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Change-Id: I0387ccf6970e6169cbebd232ae210731338d0900
Signed-off-by: Hannah Williams <hannah.williams@intel.com>
Reviewed-on: https://review.coreboot.org/20755
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
In S3 resume, wifi is one of the wake sources.
If elog is enabled in config, then log wifi wakes in elog.
BUG=b:36992859
TEST= Build for Soraka. Do WoWlan during S3. Verify elog having update
on wake due to Wifi.
Change-Id: I7d42c5c81e0a3f7a3f94c3f6b7d2ebdf029d1aff
Signed-off-by: Naresh G Solanki <naresh.solanki@intel.com>
Reviewed-on: https://review.coreboot.org/20455
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This excludes files which are mostly spaces, which I felt should be
handled separately.
Change-Id: I33043a3090e2fc6e9d2fd81e8a5e46fb6cb0aa35
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/20731
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
Change-Id: Iabdaaaee49e8c5cead304cda66412aa36a2ffd19
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/20729
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
As per discussion with CSME team, ME is NOT using PCI Config
Space register HFSTS2 Bit 10 to update ME power-gated status.
ME goes to CM0-PG state after ME device becomes idle after
Bit 2 of MMIO register offset 0x800 (D0i3 Control - HECI1_D0I3C)
is being set.
And to retrieve the PG status of ME, one should read from the
PWRMBASE+offset 0x590 (which should give the value 0xF9) and
PWRMBASE+offset 0x594 (which should give the value 0xFF).
But, also it needs some time for the ME FW to go to idle state
and reflect these values in PWRMBASE registers after D0i3 bit
is being set. This does not happen instantly.
So, in coreboot, if we read the ME PG state in finalize.c, which
happens just after FSP Notify phase, where actually ME D0i3 bit
is set, we do not read the correct PG state values (i.e, 0xF9
and 0xFF).
But, once it boots to Kernel, if we read those same registers
through iotool mmio_read32 command, we get correct values.
So, removing the ME PG state prints from coreboot, since it is
actually showing wrong information, although ME Power Gating is
successful.
Change-Id: Idd31a9803b4c9db7d4bb8bbec5374583a8df0c41
Signed-off-by: Barnali Sarkar <barnali.sarkar@intel.com>
Reviewed-on: https://review.coreboot.org/20172
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
The functionality of the FAN controller is extended to provide a
lowest startup speed of the FAN. Add the parameter "fanmin" to
the fan_ctrl_t structure and initialize the value.
Change-Id: Ib2e093ed6f5fc29bbea879779eb4777eb371b937
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/20789
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
The parameter shall be FANStartSpeed instead of FANStartpeed.
Change-Id: I977da687ba8d9d0bad4c184cd0945ecaa52286ad
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/20788
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Add ASL for the Elan touchpad driver connection in ChromeOS.
This is based on the Auron and Rambi ASL. The AMD ACPI code
doesn't have the auto table generation the newer Intel
Chrome SOC use.
Device visible to OS: /sys/bus/acpi/devices/ELAN0000
Change-Id: Id3fc8c8855b0296f43a502e81143498d663468ec
Signed-off-by: Ivy Jian <ivy_jian@compal.com>
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/19844
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Clean up the ASL whitespace and formatting to match the iasl -d
style as other parts of coreboot.
Change-Id: I61689cb55dc26cbad160d45aa0a36c00b386fe0c
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/19843
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
The AMD internal A-link (AAHB device) doesn't support an IRQ,
so remove it. This solves a conflict with the GPIO IRQ required
for touchpad operation.
Change-Id: Iefaf33cfb2babc29d35b5372fc3a338a72c78a4a
Signed-off-by: Ivy Jian <ivy_jian@compal.com>
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/19842
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
WLAN_PE_RST control was moved from EC to SoC, it connected to GPP_B8.
Configure GPP_B8 to drive low.
TEST=Wifi card is detected and connect to an AP.
Change-Id: I6a6ea0ddefe8402284fe37665864c7a1961cbc15
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/20804
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
The Kahlee Nuvoton EC firmware doesn't support SERIRQ quiet mode, yet.
Set continuous mode until the quiet mode feature is available. This
allows keyboard and other EC based interrupts through.
Change-Id: If77c91fde2bd0f4da85413879fefb753ae6297de
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/19840
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
GPIOs for I2C3 were being unset in amdinitmid if the GPIO
enable table wasn't passed. It had been initialy set in amdinitreset.
Pull the GPIO settings into their own file that can be used in
bootblock and later stages.
Change-Id: I41cd7873f8c8543c95ad8653e0a3887f7d0487a2
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/19839
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Enable:
GPP0 x1 - WLan
GPP1 x1 - Card Reader
Change-Id: Idbfc2a3260b85949810bdd8dc904e59f8a779e48
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/19838
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
The EC is a legacy 8042 device. Don't set LEGACY_FREE and correctly
report in the FADT.
Change-Id: I041ea4b44372178f3d6073b6ebc8003abc097703
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/19836
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add the basics for building as a ChromeOS device. ChromeOS
and ChromeEC are dependent on each other, so bring them in
together. The EC is a Nuvoton and you can find additional
details in the Chromium EC repo.
Add the Google HWID "Kahlee TEST 6421".
The chromeos.fmd for Kahlee takes advantage of the AGESA
located outside cbfs and includes typical RW, VPD, and
MRC areas.
There are some updates required to depthcharge, vboot, GPIOs,
and the ChromeEC before we have a complete-ish system.
Change-Id: Ifb0a6afc01dd80ef9e7bb81039d9152936043999
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/19835
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Update GPIO settings based on the schematic.
Change-Id: Ic8a876198a3ba9029d1aabb273418923e40bfcc6
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/19834
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Update for a single DIMM with an SPD at address A0.
Change-Id: I646f079c99cbaffd7094773243600c3030308325
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/19833
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Kahlee does not use the AMD IMC. Remove the files and calls.
Change-Id: Ia837551b592b4f473eb38c06c516586fb6c95c88
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/19832
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Update for the Stoney Ridge FT4 package and the on chip UART.
Change-Id: I11468834a9ef03da084c156c74d55a19416d98c4
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/19831
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Copied from amd/gardenia. Update the appropriate board name strings.
Uses the soc/ structure.
Change-Id: Ia68b16969518f4d63d5d2dea7658a472b2daca05
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/19830
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Remove the unused support code from the old multi-device hudson
SD controller. The binaryPI blob contains the correct steps
for setting up SD and the public BKDG doesn't completely document
the controller.
The sd.c file was using device IDs not associated with the Stoney
Ridge APU. The hudson_enable() code removed was also looking for
incorrect device IDs and the PM_MANUAL_RESET register doesn't
behave as the source indicates.
The SD default settings may be overridden. Future improvements
may include a few Kconfig options and a weak call to the mainboard
for overriding additional defaults.
BUG=chrome-os-partner:62580062
Change-Id: I7dbd70320740e8a05e6bf16af125d67012f20674
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/20401
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Add Kconfig selects for vboot and update the makefile to pick up
files to be used in verstage.
Change-Id: If5c439a330d687156006aec2ebaea18ff2c96b3e
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/19756
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add dedicated CAR setup and teardown functions and Kconfig
options to force their inclusion into the build. The .S files
are mostly duplicated code from the old cache_as_ram.inc file.
The .S files use global proc names in anticipation for use with
the Kconfig symbols C_ENVIRONMENT_BOOTBLOCK and POSTCAR_STAGE.
Move the mainboard romstage functionality into the soc directory
and change the function name to be compatible with the call
from assembly_entry.S. Drop the BIST check like other devices.
Move InitReset and InitEarly to bootblock. These AGESA entry
points set some default settings, and release/recapture the
AP cores. There are currently some early dependencies on
InitReset. Future work should include:
* Pull the necessary functionality from InitReset into bootblock
* Move InitReset and InitEarly to car_stage_entry() and out of
bootblock
- Add a mechanism for the BSP to give the APs an address
to call and skip most of bootblock and verstage (when
available) (1)
- Reunify BiosCallOuts.c and OemCustomize.c
(1) During the InitReset call, the BSP enables the APs by setting
core enable bits in F18F0x1DC and APs begin fetching/executing
from the reset vector. The BSP waits for all APs to also
reach InitReset, where they enter an endless loop. The BSP
sends a command to them to execute a HLT instruction and the
BSP eventually returns from InitReset. The goal would be to
preserve this process but prevent APs from rerunning early
code.
Change-Id: I811c7ef875b980874f3c4b1f234f969ae5618c44
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/19755
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Use the appropriate read32() and write32() calls. Remove unnecessary
cast.
Change-Id: Ib5430bdb30844d3508a09ddb77a969c0628f6c7d
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/20791
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
The format of the D14F3xA0 SPI Base_Addr register is different
than a traditional BAR. Change the function to preserve any
enables already in place. Change the AND mask to remove the
reserved field and the enables.
Change-Id: I9a43c029a2e1576703ce9cdc787d18658e9190a5
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/20790
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
The following changes have been applied for GPIO:
1. Correct port id using by GPIO community 3 for CNL-LP.
2. Correct number of doubleword for each pad from 2 to 4.
Change-Id: I717d1ffba8e6722543f4cf8083fe6145fa85e184
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/20775
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
The mc_apl1 mainboard needs to disable the RAPL algorithm for a constant
power management of the processor package. An active RAPL algorithm
leads to negative effects with our real time software.
Change-Id: I09ca56a034fd3896a000e64cac35f12fb507a682
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/20760
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Apollo Lake SoC supports configuration of Running Average Power Limits
(RAPL) for package domain. This feature is not required for all APL
mainboards. According to the APL SoC EDS Vol 4 chapter 18.4 Power
Limiting Control it is not necessary to enable the RAPL algorithm per
default. For that reason make the RAPL configuration selectable.
Change-Id: Ib737b162f72b76c15e5768859f9099e2e7ef6426
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/20759
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
If we dont have a constant TSC rate, timestamp table
has odd leaps and may appear to run backwards. Add
functionality to apply a factor such that all stamps
are in the same timebase.
Change-Id: Idab9c2c00e117c4d247db8cc9a2897640fa01edd
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/19330
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Configure GPIO.1 and GPIO.2 as sensor SDA and SCL respectively
for TPS68470 PMIC in daisy chain mode.
* GPIO.1: Sensor SDA in daisy chain mode.
* GPIO.2: Sensor SCL in daisy chain mode.
BUG=b:38326541
BRANCH=none
TEST=Build and boot soraka. Dump and verify that the generated DSDT table
has the required entries. Verified that sensor probe is successful.
Change-Id: I7f9686427772a33c06e4cdaafee9b0349d700639
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Reviewed-on: https://review.coreboot.org/20665
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Rajmohan Mani <rajmohan.mani@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
resources
This patch controls the camera devices power through ACPI power resource.
* Add Opregions for PMIC1 and PMIC2,
* TI_PMIC_POWER_OPREGION
* TI_PMIC_VR_VAL_OPREGION
* TI_PMIC_CLK_OPREGION
* TI_PMIC_CLK_FREQ_OPREGION
* Add power resources for sensors and VCM,
* OVTH for CAM0
* OVFI for CAM1
* VCMP for VCM
* Implement _ON and _OFF methods for sensor and VCM module's power on
and power off sequences.
BUG=none
BRANCH=none
TEST=Build and boot kblrvp. Dump and verify that the generated DSDT table
has the required entries. Verified that sensor probe is successful.
Change-Id: I02c4784ab3f4d6e1f0e657ad50b727ff11da8b9c
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Reviewed-on: https://review.coreboot.org/20663
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Bind the camera sensor and CIO2 devices through the ports and endpoints
configuration available in _DSD ACPI object.
* Port represents an interface in a device.
* Endpoint represents a connection to that interface.
BUG=none
BRANCH=none
TEST=Build and boot kblrvp. Dump and verify that the generated DSDT table
has the required entries.
Change-Id: If328864dbb61586a4887c7fcae740a12eda7cc92
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Reviewed-on: https://review.coreboot.org/20662
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This patch adds mipi_camera.asl and enables
I2C2, I2C3, CIO2 and IMGU devices,
* Add TPS68470 PMIC1 and PMIC2 related ACPI objects.
* Add OV cameras related ACPI objects.
* Add Dongwoon AF DAC related ACPI objects.
* SSDB: Sensor specific database for camera sensor.
* CAMD: ACPI object to specify the camera device type.
KBLRVP has two PMIC's sitting on I2C2 and I2C3. CAM0 and
CAM1 power requirements are handled by PMIC1 and PMIC2 respectively.
BUG=none
BRANCH=none
TEST=Build and boot kblrvp. Dump and verify that the generated DSDT table
has the required entries.
Change-Id: Ibaf26dad74ca1e7c9f415ae75c4ed8558ad99e2f
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Reviewed-on: https://review.coreboot.org/20661
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
init_igd_opregion itself is supposed to return cb_err so this adds
error handling, just like other implentations of write_acpi_tables do it.
this had been found by coverity:
*** CID 1378270: Error handling issues (CHECKED_RETURN)
/src/soc/intel/skylake/igd.c: 147 in write_acpi_igd_opregion()
141 /* If IGD is disabled, exit here */
142 if (pci_read_config16(device, PCI_VENDOR_ID) == 0xFFFF)
143 return current;
144
145 printk(BIOS_DEBUG, "ACPI: * IGD OpRegion\n");
146 opregion = (igd_opregion_t *)current;
CID 1378270: Error handling issues (CHECKED_RETURN)
Calling "init_igd_opregion" without checking return value
(as is done elsewhere 5 out of 6 times).
147 init_igd_opregion(opregion);
148 update_igd_opregion(opregion);
149 current += sizeof(igd_opregion_t);
150 current = acpi_align_current(current);
TEST=Built
Change-Id: If6f5d53037f093607d89cfe8faf193d55de7f6c4
Found-by: Coverity (CID 1378270: Error handling issues (CHECKED_RETURN))
Signed-off-by: Martin Kepplinger <martink@posteo.de>
Reviewed-on: https://review.coreboot.org/20766
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
|
|
Add both Cannonlake U DDR4 RVP and Cannonlake Y LPDDR4 RVP support.
Implement SPD entry to FSPM for both platforms, seperated platform
specific DQ/DQS/Rcomp input to FSPM as well.
Change-Id: If71662353ddba89a9e831503a2d80dd5ebd65de3
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/20503
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Sets RAPL PL1 power to ~6W.
Note: 7.5W setting gives a run-time 6W actual measured power.
Tested on GLK w/kernel 4.11.0 by reading MSR 0x610 at runtime
and comparing to measured power on an instrumented board.
Change-Id: I07caeb2895a579387025d3b0fb7f1d2c3d5e2665
Signed-off-by: Cole Nelson <colex.nelson@intel.com>
Reviewed-on: https://review.coreboot.org/19746
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
GLKRVP is a reference board for GLK SOC
RVP1 has DDR4 and RVP2 has LPDDR4
RVP2 is enabled by default and CONFIG_IS_GLK_RVP_1 should be selected
if building for RVP1
GLKRVP can work with internal Intel EC or external Chrome EC AIC.
For internal EC, CONFIG_EC_GOOGLE_CHROMEEC will not be selected (
CONFIG_GLK_INTEL_EC should be selected for internal EC config)
By default, CONFIG_GLK_CHROME_EC is selected for external ChromeEC AIC
config.
Signed-off-by: Hannah Williams <hannah.williams@intel.com>
Change-Id: Iab688aca6a4f5c5e32801215ba3a1a440e50fbef
Reviewed-on: https://review.coreboot.org/19604
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Gather related code in the new file drivers/pc80/rtc/mc146818rtc_boot.c,
call sanitize_cmos() from C environment bootblock.
Change-Id: Ia5c64de208a5986299c0508d0e11eeb8473deef1
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/20768
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Fixes builds with BOOTBLOCK_CONSOLE && USE_OPTION_TABLE.
Change-Id: I1c7e9baa60f33c2c3651e2def0335454f7e20451
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/20767
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
The values were verified to be correct with the KabylakeFsp0001 from
github. Skylake FSP documentation disagrees so YMMV.
Change-Id: I1ee04dbbed48d5376dbc24ae70753b059f2646eb
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/20765
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Update glk header files as per v52_27 FSP code.
Change-Id: I8e313a2b854e60b1ad8a5c6e080641e323de56a8
Signed-off-by: Ravi Sarawadi <ravishankar.sarawadi@intel.com>
Reviewed-on: https://review.coreboot.org/20673
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
SMBIOS memory HOB produced by glk FSP v52_27 has new structure
members, which are not available in current apl FSP. New FSP-m
header file in https://review.coreboot.org/#/c/20673/ lists new
SMBIOS structure members.
Break memory HOB save routine into different functions for glk
and apl to accomodate new changes.
Change-Id: I33c6e4f2842cebbb326b6a05436fa69e3836ffc6
Signed-off-by: Ravi Sarawadi <ravishankar.sarawadi@intel.com>
Reviewed-on: https://review.coreboot.org/20674
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Current implementation of itss_irq_init() uses 8 bit write access to
IRQ routing registers which is not supported on Apollo Lake.
This commit moves the register access from 8 bit to 32 bit so that this
function can be used with every platform.
Change-Id: I15c3c33a16329fd57f0ad7f99d720adbf300d094
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/20680
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Fix the OEM settings for two ports. Fix and clarify comments to
reflect Rev. B of the board design.
Change-Id: I2812ea5945f67229872e78041c771606047bbbec
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/20744
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: If8e82a291f666d5f310422b100f02d5df17ab74e
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/19255
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Interrupt 11 is not used by legacy devices and so can always be used
for PCI interrupts. Full legacy IRQ routing is complicated and hard to
get right.
Change-Id: I6c718f4b9fb91ffcc4a136120581a4fcd7ec7231
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/19254
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Fixes warning by GCC 7.1:
note: did you mean to use logical not?
Change-Id: If8167c6fe88135ae89eb795eeda09e6937b1684f
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/20698
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Convert from #if to if().
Change-Id: I50b3ed9ecd5947ff625536b196d90ebd4e8f1c56
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/20746
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Make sure to set only one bit instead of arbitrary bits set in argument.
Change-Id: I39426193d15d8581f79bc2a45c0edb53b19a2cd3
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/20707
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Convert from #if to if().
Change-Id: I7c149856da22b72d2a83bd7f06d031df328dbb35
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/20745
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Fixes GCC 7.1 error:
error: '<<' in boolean context, did you mean '<' ?
Change-Id: I1a28522279982b30d25f1a4a4433a1db767f8a02
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/20699
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Change-Id: I2cd210dd0443b854294ce7ee8e267594e3ea1780
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/20651
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
Assert incase unable to locate hob list pointer due to cbmem
is not available.
Change-Id: I17f54b07ab149ae06d09226ed9063189d829efe2
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/20749
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
As per GCC 7.1 compiler struct reset_reply is considered
as uninitialized inside send_heci_reset_message function.
Change-Id: Ide53a9267dfba1a00263ada1d7016a48ecb9aad8
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/20739
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
coreboot was setting SPI FPR register to protect the
mrc_cache data range stored in flash. This programming was being done
after FSP Notify 1.
But, FSP was locking the SPI by setting FLOCKDN Bit during Notify
phase 1, due to which coreboot was unable to protect that range.
As solution, FSP introduced a new UPD SpiFlashCfgLockDown to skip
the lockdown of flash on interest of bootloader. Set that UPD to 0
to skip the lockdown of FAST_SPI flash from FSP.
The same is being done from coreboot after end of Post at finalize.c
file.
BUG=b:63049493
BRANCH=none
TEST=FPR can be set properly to protect the mrc_cache range. The
issue reported in the bug doesn't come when both software and
hardware WP is enabled with this patch.
Change-Id: I3ffca2f1b05ab2e4ef631275ef7c3a6e23e393aa
Signed-off-by: Barnali Sarkar <barnali.sarkar@intel.com>
Reviewed-on: https://review.coreboot.org/20645
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
A new UPD named SpiFlashCfgLockDown is added in the FSP-S
header file.
This change is going to come in FSP in the next FSP release.
This patch is pushed to urgently fix the SPI FPR locking issue.
CQ-DEPEND=CL:*414049
BUG=b:63049493
BRANCH=none
TEST=Built and boot poppy
Change-Id: I4725506103781a358b18ee70f4fdd56bf4ab3d96
Signed-off-by: Barnali Sarkar <barnali.sarkar@intel.com>
Reviewed-on: https://review.coreboot.org/20644
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Use 16bit write to avoid touching the upper two bytes that may cause
write cycle to fail in case a prior transaction has not completed.
This function sets the WRSDIS(Bit 11) and FLOCKDN (Bit 15) of the
SPIBAR + BIOS_HSFSTS_CTL. While WRSDIS is lockable with FLOCKDN,
writing both in the same cycle is guaranteed to work by design.
Avoid read->modify->write operation not to clear the RW1C bits
unintentionally.
Change-Id: Ia7880aaca0ed64150c994d49786a0a008bbaa98b
Signed-off-by: Barnali Sarkar <barnali.sarkar@intel.com>
Reviewed-on: https://review.coreboot.org/20643
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Change-Id: Id9846ceb714dceaea12ea33ce2aa2b8e5bb6f4df
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/20728
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
This excludes some files in the device/oprom/x86emu folder which
are mostly spaces, and which I felt should be handled separately.
debug.c, decode.c, fpu.c, ops.c, ops2.c, & prim_ops.c
Change-Id: I5c12d3fc942c9ad99bbe6e6e54db93e5a8402392
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/20730
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Change-Id: I332c44c6db0a5ea05db076474caf77d6c50d4673
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/20732
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Earlier 15ms time-out was kept for SPI transactions which was not
enough for SPI Erase transactions.
Increase the max time-out time to 5 secs which was present in SKL
before common code.
This increase in time-out won't disturb other SPI transactions like
Read, Write or Read Status, since, for those it will come out of
the loop once FDONE bit or FCERR bit is set.
BUG=b:63959637
BRANCH=none
TEST=Built and booted poppy and all SPI transactions succeeded.
Change-Id: I1c015d80b33677de11755fb2097373631d1fa8c4
Signed-off-by: Barnali Sarkar <barnali.sarkar@intel.com>
Reviewed-on: https://review.coreboot.org/20738
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
BUG=b:63876329
BRANCH=none
TEST=none
Change-Id: I98c700d5b928c031129cf0138d22652a28d1ad1d
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/20752
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
It requires changes to match the hardware. Except for the weak
attributes that are now removed in coral's copy, the file is identical
to the baseboard version.
BUG=b:63876329
BRANCH=none
TEST=none
Change-Id: Ib0c5f0ecae9919f20631dacef0253416989fb011
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/20751
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
The newline lint check just went in, and immediately broke the build
due to a commit that went in earlier today.
This fixes the build.
Change-Id: Ic4ba8ce0c8085861bc6c654afdee3fea9f4621fc
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/20754
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Fix regression introduced by commit 7ffb329f.
The default value for usb_always_on is no longer sane and is replaced
by the same default that is used on all other boards (disabled).
Change-Id: Ia8854a8491bc56507d01e08e1ca1e195a1d62bfc
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/20575
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Enable SOC_INTEL_COMMON_GFX_OPREGION for all FSP versions.
Allows to get rid of opregion.c, as it's no longer needed.
Change-Id: I39190488e12917a09dbf7ee3947a33940ebc290b
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/20222
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
|
|
Function copied from i82801gx with offsets fixed for i82801lx.
Change-Id: Ib420c69470c3190cc1eac234ce68a18382fbc04a
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/19253
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Change-Id: I8febb8d74e2463622cab0313c543ceebec71fdf4
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/20705
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Change-Id: Iaab26033e947cb9cf299faf1ce6d40a90a9facbe
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/20704
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
After updating to Wacom Firmware version 501, touchscreen can't work.
Wacom FW (ver. 501) enables STOP function.
STOP Pin:
High: Normal Operation
Low: Stop Scanning
So pull TOUCHSCREEN_STOP_L high
BUG=b:37007801, b:37265219
BRANCH=none
TEST=manual testing on Soraka board and touchscreen works at boot
and after suspend/resume.
Change-Id: I8a2bdce1554fd99dea30cf91fa48d0529f40b7b0
Signed-off-by: Wisley Chen <wisley.chen@quantatw.com>
Reviewed-on: https://review.coreboot.org/20664
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
File copied from i82801gx.
Change-Id: I107087b6448f18b6a5ae21c2ae0392c057dd23b2
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/19252
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Adapted from i82801gx.
Change-Id: I9108a45135908b7c4e74e9df3bb8f89f55893299
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/19251
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
The romstage for both is line-for-line identical.
Merge both into P2B-DS so it benefits from my
modernization efforts.
Change-Id: Idd964f4c5c4dfd9e2e0ac4a4f41e4ee9a84a729c
Signed-off-by: Keith Hui <buurin@gmail.com>
Reviewed-on: https://review.coreboot.org/20691
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
The romstage for both is line-for-line identical.
Merge both into P2B-LS so it benefits from my
modernization efforts.
Change-Id: I2d1a46236f83a4955ceb5e98b576cce0560f28df
Signed-off-by: Keith Hui <buurin@gmail.com>
Reviewed-on: https://review.coreboot.org/20690
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Romstage of many 440BX boards included headers that are not used.
Remove them as part of a bigger cleanup effort.
Change-Id: I89ddeda3c90e1a4907c05851185b69f3b29e54ba
Signed-off-by: Keith Hui <buurin@gmail.com>
Reviewed-on: https://review.coreboot.org/20693
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
I am able to complete a board-status run over onboard ethernet
(ie. it works) without this entry, so it's not necessary.
Change-Id: Iabdf1a1ff3c904bea1b7b5eaefb1d23831dd2cb9
Signed-off-by: Keith Hui <buurin@gmail.com>
Reviewed-on: https://review.coreboot.org/20683
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
There are 4 routines used in RAM init that most if not all
i440bx mainboards call in the same order. Implements a single
RAM init routine for them to allow for future consolidation.
Boards to be changed to use this one routine in a future change.
Change-Id: Ib553b07b117de12b7982586bce0f9355f55013a0
Signed-off-by: Keith Hui <buurin@gmail.com>
Reviewed-on: https://review.coreboot.org/20676
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
