| Age | Commit message (Collapse) | Author |
|---|
|
The TSC has been observed to be ticking at a non-constant rate
in early boot. The root cause is still not known, but this
misbehavior necessitates an alternative monotonic timer source.
Use the perf TSC which ticks at 100 MHz. This also means the
timestamp table is not accurate as well. Root cause of TSC rate
instability needs to be resolved in order to fix that.
BUG=b:72170796
Change-Id: Ie052169868a9d9f25f8cc0ce8dd8251b560e671f
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/23397
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
|
|
For the internal eMMC to be used by non-chrome for installation,
the CARD device and _RMV methods are required. Without these,
other OSes does not show the eMMC as a valid installation target.
TEST= boot CNL-RVP with Tiano payload and install Windows 10
to the internal eMMC drive.
Change-Id: Icfdccd88bc113d97c2fabf4c63d8d772737a6057
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/23314
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Solution: To do an additional config read to the SD controller
after the controller has been power gated (put to D3)
Change-Id: Ia2438c767332b0e2d413c71b06b052bf9ab4a96c
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/23313
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Solution: To do an additional config read to the eMMC controller
after the controller has been power gated (put to D3)
Change-Id: Ieac939c9108e84ba6c7c26b1a49aaf829d8456b7
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/23312
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
In ramstage the device_operations are needed for the i2c designware
host controller. Move the intel/common/block/i2c implementation
into the generic driver so other platforms can take advantage of it.
BUG=b:72121803
Change-Id: Id249933fadcc016bfba00e7a6d65f56dfc220724
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/23372
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
|
|
Rename the following functions to ensure it's clear that the designware
i2c host controller driver is the one that these functions are
associated with:
i2c_get_soc_cfg() -> dw_i2c_get_soc_cfg()
i2c_get_soc_early_base() -> dw_i2c_get_soc_early_base()
i2c_soc_devfn_to_bus() -> dw_i2c_soc_devfn_to_bus()
i2c_soc_bus_to_devfn() -> dw_i2c_soc_bus_to_devfn()
BUG=b:72121803
Change-Id: Idb7633b45a0bb7cb7433ef5f6b154e28474a7b6d
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/23371
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
If one wants to implement both i2c_bus.h and i2c_simple.h APIs
the compilation unit needs to be guarded or coordinated carefully
with different compilation units. Instead, name the i2c_bus
functions with _dev such that it indicates that they operate on
struct device. One other change to allow i2c_bus.h to be built in
non-ramstage environments is to ensure DEVTREE_CONST is used for
the dev field in struct bus.
BUG=b:72121803
Change-Id: I267e27e62c95013e8ff8b0728dbe9e7b523de453
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/23370
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Change-Id: If5a72786d1119908073488c1d6d8787ac0f4f95c
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/23276
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Change-Id: Id4e05941122c8756f15d5d24482e4cdc04215c55
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/23275
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Change-Id: Ie472092f8926231f4e1bd1fb12839b532b4ad158
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/23279
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
This patch adds AC and DC loadline settings since vr_config_enable is
set. Without correct AD/DC loadline settings, VRs reported incorrect
VID values which caused CPU freqency clipping. The clipping reason
could be retrieved from MSR 0x64F. From VRTT report, the AC/DC
loadline resistances are within spec, we can use default value defined
in Table 6-1, doc #543977.
BUG=b:70646304
BRANCH=None
TEST=emerge-fizz coreboot chromeos-bootimage & Read AC/DC loadline
settings from DCI to ensure the values were programmed correctly.
Change-Id: Id0ce29fa5726ca3711aa4c822fb123e2de7bc48f
Signed-off-by: Gaggery Tsai <gaggery.tsai@intel.com>
Reviewed-on: https://review.coreboot.org/23349
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Audio DMIC_DATA needs to be ON in S0ix to support Wake on Voice.
By doing this, SoC can see the DMIC DATA and use for WoV processing.
Thus configuring GPIO_173 as IGNORE IOSSTATE.
TEST=put DUT in S0ix, verify DUT wakes up
Change-Id: I8bf403564e927deb8fed7f415e334bb230107cb0
Signed-off-by: Ravi Sarawadi <ravishankar.sarawadi@intel.com>
Reviewed-on: https://review.coreboot.org/23246
Reviewed-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Tune I2C params for I2C bus 5 to ensure that the frequency does not
exceed 400KHz.
BUG=b:65058277
BRANCH=None
TEST=Measured bus frequency for audio <= 400MHz
Change-Id: I18bca023a6a0fe21e6f46f8688264d3c04d77f25
Signed-off-by: Shelley Chen <shchen@chromium.org>
Reviewed-on: https://review.coreboot.org/23359
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Kahlee uses LPC TPM while grunt is using Cr50 connected to I2C. Create
the appropriate selection based on selected board, and if grunt then
define the I2C address.
BUG=b:69416132
BRANCH=none
TEST=make all
Change-Id: Ia866f80de0164d8cec84e204a5fe93bb53df547f
Signed-off-by: Chris Ching <chingcodes@chromium.org>
Reviewed-on: https://review.coreboot.org/22960
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Enable S0ix wake mask programming from coreboot using unified host event
programming interface. Lazy s0ix wake mask helps to configure s0ix wake
mask during boot and EC sets the wake mask during S0ix entry.
BRANCH=none
BUG=b:63969337
TEST=verify masks with ec hostevent command on S0, S3, S5 and S0ix
Change-Id: If56d1de5d1157c8cf9c418e3a9d2396ffcfcb0fd
Signed-off-by: Jenny TC <jenny.tc@intel.com>
Reviewed-on: https://review.coreboot.org/21610
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Function platform_FchParams_reset() is now an empty function, remove it,
its header declaration and its use.
BUG=b:64140392
TEST=Build kahlee.
Change-Id: I3f3efc072a2e198433d0e261dacbbd4a8ff327d7
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/22989
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Fill up the dummy gpio_set_stage_reset[] and gpio_set_stage_ram[] with data
from agesa_board_gpios[], wrap format and delete agesa_board_gpios[].
Finally, make platform_FchParams_reset() an empty function.
BUG=b:64140392
TEST=Build gardenia.
Change-Id: Id2ea63656a7d2f20f55fc5a4c75457db85b80cbd
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/22990
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Fill up the dummy gpio_set_stage_reset[] and gpio_set_stage_ram[]
with data from agesa_board_gpios[], wrap format and delete
agesa_board_gpios[] and get_gpio_table(). Then remove the
get_gpio_table() call from BiosCallOuts.c. Finally, remove
get_gpio_table() from
google/kahlee/variants/baseboard/include/baseboard/variants.h.
BUG=b:64140392
TEST=Build grunt. Build and boot kahlee, recording serial output. Search
for "stage bootblock" and "stage ramstage", indicating GPIO being
programmed.
Change-Id: I88bf2c855105a6bc458aedfc6da7725662695667
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/22988
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Add new function sb_program_gpio to be called after AGESA init_reset
and some point within ramstage. For AGESA init_reset, change
amd/stoneyridge/bootblock/bootblock.c function bootblock_soc_init
(add the function after the call to AGESA function).
BUG=b:64140392
TEST=Build kahlee, grunt, gardenia.
Change-Id: I38da26cd1e20617958a6b17d55b7d7c08b8a0230
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/22987
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Create a GPIO programming function that can be called from multiple
stages (bootblock, romstage and ramstage) that will program only the
GPIO specific to the particular stage.
Add dummy table to kahlee, grunt and gardenia to be able to test a build.
BUG=b:64140392
TEST=Build kahlee, grunt and gardenia with GPIO programming call at
bootblock. This call is removed before commit, so bootblock.c is not
committed.
Change-Id: I88d65c78a186bed9739bc208d5711a31aa3c3bb6
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/22986
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Change e1a75d4(soc/intel/skylake: Override KBL IccMax settings)
provides correct iccmax settings for kbl-u based on the SKU. Thus,
there is no need to override these values in devicetree. This change
gets rid of iccmax settings in the nami devicetree.
Change-Id: Ie7220bae71fcc597fc20c5e98793d4ea7af5650e
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/23265
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
PC10 is a necessary condition for S0ix entry. With the current C-state limits,
CPU fails to enter PC10 during S0ix. C-state Latency control limits
have to be tuned to new values for PC10 entry.
Change-Id: I0f5227f9c3c10c5a9e335ab118eb0ec185445374
Signed-off-by: Vaibhav Shankar <vaibhav.shankar@intel.com>
Reviewed-on: https://review.coreboot.org/23220
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
The HeapAllocateBuffer and HeapDeallocateBuffer functions are not used.
Change-Id: I491a796d87afd0e37051f9caabfff3f70d4d803c
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/22069
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Change-Id: Ib8d4d3ee490188ce171188d859549da586683e26
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/21695
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
With no boards left using AGESA_LEGACY, wipe out remains
of that everywhere in the tree.
Change-Id: I0ddc1f400e56e42fe8a43b4766195e3a187dcea6
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/18633
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Most affected boards set the function disabled (FD) register to an
arbitrary state dumped from systems running the vendor BIOS. This
makes it impossible to enable the devices in devicetree and a pretty
big mess of course because nobody cared to keep the register in sync
with the devicetree.
To get completely rid of most of the writes to FD, move setting of
PCH_DISABLE_ALWAYS into the southbridge code where it belongs.
Change-Id: Ia2a507cbcdf218d09738e2e16f0d3ad1dcf57b8b
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/23255
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hal Martin <hal.martin+coreboot@gmail.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Bill XIE <persmule@gmail.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Macro renamed to be in accordance with the name used in the datasheet.
Change-Id: I5671c39608769b2c5ea2fb17809430f56e5f0b71
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/23330
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Add NHLT and dt support for max98373 amp
BUG=None
TEST=check SSDT and verify entries for max98373
TEST=check NHLT ACPI tables included blobs for max98373
Change-Id: I0b402f89f1ece9e62a394f713c4b0feff29bd1e5
Signed-off-by: N, Harshapriya <harshapriya.n@intel.com>
Signed-off-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Reviewed-on: https://review.coreboot.org/22674
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Add a device driver to generate the device and required properties
into the SSDT for max98373.
TEST=verified SSDT contained relevant params
BUG=None
Change-Id: Id45f74e52855f4b19276e1d3d673d5448207ef4b
Signed-off-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Signed-off-by: N, Harshapriya <harshapriya.n@intel.com>
Reviewed-on: https://review.coreboot.org/22673
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Add NHLT and dt support for Audio with Max98357 and DA7219
TEST=verified NHLT tables and SSDT entries
BUG=None
Change-Id: If7960eb6bb441f35cbd9a8a6acc37f03e04e3b70
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Signed-off-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Reviewed-on: https://review.coreboot.org/22144
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Add audio NHLT support for cannonlake, reference code is implementation
in apollolake.
CQ-DEPEND=CL:*533799
BUG=None
TEST=None
Change-Id: Ie8561cc64412bef54329b317874a8fe12e0bf889
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Signed-off-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Reviewed-on: https://review.coreboot.org/22134
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This patch adds a member device_index to r8168 chip information which
allows driver to identify which NIC card requests MAC address.
In this implementation, only 10 NIC cards are supported, the device
index is in the range of 0 to 10. Regarding to MAC address mapping,
when there is only one NIC on DUT, it is treated as a special case
mapping to "ethernet_mac" in VPD for backward compatibility. When
there are multiple NICs on DUT, they are mapping to "ethernet_macN"
where N is [0-9].
Device tree configuration:
For single NIC: .device_index = "0", maps to "ethernet_mac"
For multiple NICs: .device_index = "[1-10]", maps to
"ethernet_mac[device_index - 1]"
BUG=b:69950854
BRANCH=None
TEST=Added device_index = [0-10] under /drivers/net in device tree &&
Programmed the mac address to VPD in shell
vpd -s ethernet_mac=<mac address> or
vpd -s ethernet-mac[0-9]=<mac address> && reboot the system.
Ensure the MAC address was fetched correctly by ifconfig command.
Change-Id: I108b9bfba39370c8906a2fa4d2b39b106e884e0c
Signed-off-by: Gaggery Tsai <gaggery.tsai@intel.com>
Reviewed-on: https://review.coreboot.org/22984
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
this enables the MRC recovery cache for zoombini & variants.
the Kconfig options are:
HAS_RECOVERY_MRC_CACHE
MRC_CLEAR_NORMAL_CACHE_ON_RECOVERY_RETRAIN
one note of caution: early board builds will likely fail to boot with:
tlcl_extend: response is 0
tlcl_extend: response is 0
tlcl_lock_nv_write: response is 0
tlcl_lock_nv_write: response is 28b
Failed to lock rec hash space(1f)
Saving nvdata
hard_reset() called!
the fix is to boot into recovery once, then it's business as usual.
using servo, this can be done with:
dut-control power_state:rec
BUG=b:71785303
BRANCH=chromeos-2016.05
TEST=boots on meowth...
Change-Id: I77f36d36a70c8c9c74a7fa3a114d3177f33a708b
Signed-off-by: Caveh Jalali <caveh@google.com>
Reviewed-on: https://review.coreboot.org/23298
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
this adds missing ACPI entries for the EC, CPU, and power button.
also, the EC to AP wakeup pin assignment is fixed.
BUG=b:71819257
BRANCH=chromeos-2016.05
TEST=booted on meowth. /sys/class/power_supply now gets populated.
Change-Id: I0d091bdf25f9a806bd36329d1f17ac34b3115e48
Signed-off-by: Caveh Jalali <caveh@chromium.org>
Reviewed-on: https://review.coreboot.org/23237
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
|
|
CONFIG_STONEYRIDGE_SATA_MODE is compared against "magical numbers".
Because actual literals are in AGESA.h and adding agesa_headers.h to
southbridge.h causes compile errors, move comparison code from southbridge.h
to southbridge.c (where they are actually used). Replace these numbers
with actual literals.
BUG=b:71754828
TEST=Build kahlee.
Change-Id: I711473bf492d5ceca026ccd112c2c389a23bdbf9
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/23296
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
At AGESA AmdInitReset, SATA enable and IDE enable (elements of
FCH_RESET_INTERFACE) are programmed twice (before calling AGESA
for AmdInitReset and from said AGESA function call out), using
different functions with different results. The first would result
in TRUE/FALSE, the second set would result in TRUE/TRUE. Use the
functions of the second set within the first set, and remove them
from the second set.
BUG=b:71754828
TEST=Build kahlle without the change, boot and record output. Rebuild
kahlee with the change, boot and record output. Compare both outputs,
the should be no change except in timing.
Change-Id: I326fcc8801542aa7feef286d02abdfe63354cdd0
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/23295
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This patch removes IccMax settings from device tree since they
are handled in SoC code from patch e1a75d.
BUG=b:71369428
BRANCH=None
TEST="USE=fw_debug emerge-fizz chromeos-mrc coreboot
chromeos-bootimage" & ensure the IccMax settings passed
to FSP are from SoC code.
Change-Id: I6b01c50a2589d1722c5bf4aa2f44a9574df818f4
Signed-off-by: Gaggery Tsai <gaggery.tsai@intel.com>
Reviewed-on: https://review.coreboot.org/23278
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shelley Chen <shchen@google.com>
|
|
Turn on the load switch to the FP MCU at startup, so the kernel can
detect it and use it.
The load switch enable pin is connected to the GPP_A11 PCH pin (aka
PCH_FP_PWR_EN).
BRANCH=none
BUG=b:71986991
TEST=on Meowth, see the kernel detecting a cros_fp device at startup:
[ 2.133456] cros-ec-spi spi-PRP0001:00: Fingerprint MCU detected.
[ 2.157420] cros-ec-spi spi-PRP0001:00: Chrome EC device registered
Change-Id: Id3c40b965a5f018c63481c2e2eea3fc8307352bd
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Reviewed-on: https://review.coreboot.org/23329
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Configure the FP MCU interface on GSPI1.
BRANCH=none
BUG=b:71986991
TEST=boot on reworked Meowth with a ZerbleBarn board attached to
GSPI1 and see the cros_ec kernel driver detecting it.
Change-Id: Ib874ddaf4948a766fd05c11f4675dbfdb679059d
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Reviewed-on: https://review.coreboot.org/23328
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
The variable t32 was originally used to do bitwise operations, but it is
not required anymore. Also, it was assigned twice accidentally, which
introduced a new Coverity Scan defect.
Found-by: Coverity (CID 1385126: (UNUSED_VALUE))
Change-Id: I77afd5064304a36991f63cf1328e13820144efb6
Signed-off-by: Gergely Kiss <mail.gery@gmail.com>
Reviewed-on: https://review.coreboot.org/23320
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
This automatically generates an FMAP region for the MRC_CACHE driver
which is easier to handle than a cbfsfile.
Adds some spaces and more comments to Makefile.inc to improve
readability.
Tested on Thinkpad x200 with some proof of concept patches.
Change-Id: Iaaca36b1123b094ec1bbe5df4fb25660919173ca
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/23150
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Remove the BiosRam read and write functions that were brought over from
the hudson source. The functionality will be superseded later with new
general-purpose functions.
Change-Id: Ib80c66b838fdbdd388a392b4fedaac36bf0bbb0c
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/22725
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The internal FCH contains 256 bytes of "BiosRam" that maintains its
state until RSMRST# is asserted or standby power is lost. Add functions
to support read and write operations.
Change-Id: I2ddf58a63e69b2775de9a8163534b13dad2ea2fe
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/22724
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
|
|
Relocate the I/O registers to the iomap for PM, PM2, and BIOSRAM.
Change-Id: I3a59adc974a8a90bfc586188b829a7252356b3cb
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/22723
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Relocate the acpi_get_sleep_type() function out of the southbridge
ramstage file. This will make it more convenient for using elsewhere.
Change-Id: Id7ba709bb867fb00ed6c7fa7526de087a3b9b3ca
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/22722
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
The cbmem location holding the heap will be used to store additional
information in subsequent patches. Remove the static designation from
agesa_heap_base.
Change-Id: Ic607432fd6500ef69b5d47793896cf12a699d8b7
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/22721
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
A subsequent patch will use GetHeapBase() in more files than
heapmanager.c. Convert it to a format more similar to existing
coreboot source.
Change-Id: I8362af849fc9d7cb1b8a93113e8d78dcac51c20a
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/22903
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
In 6c747068 "amd/stoneyridge: Put AGESA heap into cbmem" the AGESA
heap was moved completely into cbmem. This was a departure from the
"late cbmem init" method of adding it late in post, then storing the
S3 volatile data to the region. Remove the hardcoded base address
that was missed in that commit.
To prepare for S3 support, split the region into subregions for
heap, AGESA's S3 volatile storage, and an MTRR save area.
BUG=b:69614064
Change-Id: I06c137f56516f3a04091d1191cd657a0aa07320b
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/22720
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Remove the original spi.c file that writes S3 NV data to flash in a
proprietary format. The s3 folder is retained to facilitate new
development.
Change-Id: I1b5fe8e854c3d2dd71506c2acd6ff73e4b86d7d4
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/23305
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
The default time for writing MRC data to flash is at the exit of
BS_DEV_ENUMERATE but this is too early for some implementations.
Add an option to Kconfig for allowing a late option to be selected.
The timing of the late option is at the entry of BS_OS_RESUME_CHECK.
TEST=Select option and inspect console log on Kahlee
BUG=b:69614064
Change-Id: Ie7ba9070829d98414ee788e14d1a768145d742ea
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/22937
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Ported from commit e6033ce1
soc/amd/common/block/pi: Fix AGESA heap deallocator
The deallocation was always subtracting the header, even when it
shouldn't. This caused problems for the allocator where buffer
sizes were incorrect and freed and used buffers could collide.
Fix the deallocation size.
Clear deallocated concatinated buffer header memory.
Fix the initial calculation of the total buffer size
available to be allocated.
Original-Change-Id: I2789ddf72d662f24709dc5d9873741169cc4ef36
Change-Id: Ibac916fcd964adca97a72617428e3d53012e13a1
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/23309
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
All boards and chips that are still using LATE_CBMEM_INIT are being
removed as previously discussed.
If these boards and chips are updated to not use LATE_CBMEM_INIT, they
can be restored to the active codebase from the 4.7 branch.
Mainboards:
src/mainboard/a-trend/atc-6220
src/mainboard/a-trend/atc-6240
src/mainboard/abit/be6-ii_v2_0
src/mainboard/azza/pt-6ibd
src/mainboard/biostar/m6tba
src/mainboard/compaq/deskpro_en_sff_p600
src/mainboard/gigabyte/ga-6bxc
src/mainboard/gigabyte/ga-6bxe
src/mainboard/msi/ms6119
src/mainboard/msi/ms6147
src/mainboard/msi/ms6156
src/mainboard/nokia/ip530
src/mainboard/soyo/sy-6ba-plus-iii
src/mainboard/tyan/s1846
Change-Id: Id895963f9641bcaaa65e8a8cb21213a758a9ad80
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/23301
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
All boards and chips that are still using LATE_CBMEM_INIT are being
removed as previously discussed.
If these boards and chips are updated to not use LATE_CBMEM_INIT, they
can be restored to the active codebase from the 4.7 branch.
chips:
northbridge/intel/i82810
Mainboards:
src/mainboard/asus/mew-am
src/mainboard/asus/mew-vm
src/mainboard/ecs/p6iwp-fe
src/mainboard/hp/e_vectra_p2706t
src/mainboard/intel/d810e2cb
src/mainboard/mitac/6513wu
src/mainboard/msi/ms6178
src/mainboard/nec/powermate2000
Change-Id: Ib273316c59f499e6cd3a0e4c4dc4c2cce94ff291
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/23300
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add support for new memory stuffing options that will appear on
the P1 meowth boards.
new strap setting - associated SPD file
----------------------------------------
0b001 - Hynix_H9HCNNN8KUMLHR_1GB.spd.hex
0b010 - Samsung_K4F6E3S4HM_2GB.spd.hex
0b011 - Hynix_H9HCNNNCPUMLHR_4GB.spd.hex
BUG=b:69011806
BRANCH=none
TEST=none
Change-Id: Ief07f3de351d01cbc195b785c36e96de0cbf7ddb
Signed-off-by: Nick Vaccaro <nvaccaro@chromium.org>
Reviewed-on: https://review.coreboot.org/23267
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Change-Id: I44574e64e621ea60d559d593694af36c648fb7d7
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/23302
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
The name blobtool is confusing as 'blob' is also used to
describe nonfree software in binary form.
Since this utility deals with binary configurations it
makes more sense to call it bincfg.
Change-Id: I3339274f1c42df4bb4a6b30b9538d91c3c03d7d0
Signed-off-by: Denis 'GNUtoo' Carikli <GNUtoo@no-log.org>
Reviewed-on: https://review.coreboot.org/23239
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Change-Id: I5e20d98665c17d39f3f69772093a062bb905f6f9
Signed-off-by: Philipp Deppenwiese <zaolin@das-labor.org>
Reviewed-on: https://review.coreboot.org/22105
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
* Rename tlcl* to tss* as tpm software stack layer.
* Fix inconsistent naming.
Change-Id: I206dd6a32dbd303a6d4d987e424407ebf5c518fa
Signed-off-by: Philipp Deppenwiese <zaolin@das-labor.org>
Reviewed-on: https://review.coreboot.org/22104
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
* Move code from src/lib and src/include into src/security/tpm
* Split TPM TSS 1.2 and 2.0
* Fix header includes
* Add a new directory structure with kconfig and makefile includes
Change-Id: Id15a9aa6bd367560318dfcfd450bf5626ea0ec2b
Signed-off-by: Philipp Deppenwiese <zaolin@das-labor.org>
Reviewed-on: https://review.coreboot.org/22103
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Our current U22 skus (celeron and i3) actually don't support PL2,
but making sure that if we do decide in the future to use it to
make sure PL2 and PsysPl2 values are set appropriately.
BUG=b:71594855
BRANCH=None
TEST=Make sure that PsysPL2 value set to 90W with barrel jack for U42
and 65W with barrel jack for U22.
Change-Id: I084d0320128a6e05948023520a30c497c41be23b
Signed-off-by: Shelley Chen <shchen@chromium.org>
Reviewed-on: https://review.coreboot.org/23294
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Change the directory of the included cpu.asl file. This board seems to
have been omitted in 0a4e0fd "Fix the PNOT ACPI method".
Change-Id: Idc00197b1544006299e720dca59e02f6bf8f683c
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/23308
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
|
|
PMC controller gets hidden during FSP Silicon initialization
using sideband interface on CNP-PCH. Hence unable to reserve
PMC IO resources during PCI enumeration process. This causes
hang issue on non-chrome platform with CNP-PCH due to ABASE
corruption.
This patch ensures PMC IO resource (ABASE) is getting reserved
(IO address 0x1800-0x1900) and ACPI base is not overwritten by
other devices.
TEST=ABASE range is reserved along with LPC IO range during PCI
enumeration.
PCI: 00:1f.0 resource base 1800 size 100 align 0 gran 0 limit 0
flags c0000100 index 20
Change-Id: I1fbc4339ae11058fb3daedf4ffedda1904fa52ec
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/23202
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This patch ensures common block has option to reserve IO resources
based on SOC requirements. Also add pch_lpc_ prefix to maintain
same function nomenclature across all intel common block.
Change-Id: Ic00af688104bcea1aff06be6cbb20208a60e5f1d
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/23201
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
In order to make VBOOT2 independent from the CHROMEOS
kconfig option a weak method for get_write_protect_state
and get_recovery_mode_switch() is required.
Introduce a kconfig option for controlling this
behaviour.
This is a temporary fix and will be removed afterwards.
Change-Id: I3b1555bd93e1605e04d5c3ea6a752eb1459e426e
Signed-off-by: Philipp Deppenwiese <zaolin@das-labor.org>
Reviewed-on: https://review.coreboot.org/22102
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
We check for NULL here for memory_info_hob and return if it's NULL
so that the future dereferencing is proper.
Change-Id: Ie34931504ad92739fdaa68ec7989e76e8eee2595
Found-by: Klockworks
Signed-off-by: Ravi Sarawadi <ravishankar.sarawadi@intel.com>
Reviewed-on: https://review.coreboot.org/23223
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Enable S0ix wake mask programming from coreboot using unified host event
programming interface. Lazy s0ix wake mask helps to configure s0ix wake
mask during boot and EC sets the wake mask during S0ix entry.
BRANCH=none
BUG=b:63969337
TEST=verify masks with ec hostevent command on S0,S3,S5 and S0ix
Change-Id: I65173104fce258d03956bbb0e80073c47fe80fab
Signed-off-by: Jenny TC <jenny.tc@intel.com>
Reviewed-on: https://review.coreboot.org/21086
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Unified Host Event Programming Interface (UHEPI) enables a unified host
command EC_CMD_PROGRAM_HOST_EVENT to set/get/clear different host events.
Old host event commands (0x87, 0x88, 0x89, 0x8A, 0x8B, 0x8C, 0x8D, 0x8E,
0x8F) is supported for backward compatibility. But newer version of
BIOS/OS is expected to use UHEPI command (EC_CMD_PROGRAM_HOST_EVENT)
The UHEPI also enables the active and lazy wake masks. Active wake mask
is the mask that is programmed in the LPC driver (i.e. the mask that is
actively used by LPC driver for waking the host during suspended state).
It is same as the current wake mask that is set by the smihandler on host
just before entering sleep state S3/S5. On the other hand, lazy wake masks
are per-sleep masks (S0ix, S3, S5) so that they can be used by EC to set
the active wake mask depending upon the type of sleep that the host has
entered. This allows the host BIOS to perform one-time programming of
the wake masks for each supported sleep type and then EC can take care
of appropriately setting the active mask when host enters a particular
sleep state.
BRANCH=none
BUG=b:63969337
TEST=verify masks with ec hostevent command on S0,S3,S5 and S0ix
1). Verified wake masks with ec hostevent command on S0,S3,S5 and S0ix
2). suspend_stress_test with S3 and S0ix
3). Verified "mosys eventlog list" in S3 and s0ix resume to confirm
wake sources (Lid, power buttton and Mode change)
4). Verified "mosys eventlog list" in S5 resume to confirm wake sources
(Power Button)
5). Verified above scenarios with combination of Old BIOS + New EC and
New BIOS + Old EC
Change-Id: I4917a222c79b6aaecb71d7704ffde57bf3bc99d9
Signed-off-by: Jenny TC <jenny.tc@intel.com>
Reviewed-on: https://review.coreboot.org/21085
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
The PNOT method never notifies the CPU to update it's _CST methods due
to reliance on inexisting variable (PDCx).
Add a method in the speedstep ssdt generator to notify all available
CPU nodes and hook this up in this file.
The cpu.asl file is moved to cpu/intel/speedstep/acpi since it now
relies on code generated in the speedstep ssdt generator. CPUs not
using the speedstep code never included this PNOT method so this is
a logical place for this code to be.
Change-Id: Ie2ba5e07b401d6f7c80c31f2bfcd9ef3ac0c1ad1
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/23144
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
PWRS is is the power source gnvs.
Notifying CPU is needed to change P- and C-states on these events.
Change-Id: I0818d10474523fb14f7ba7cfbf61166b89442083
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/22931
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
If waking up from S5, then prev_sleep_state was correct but not when
waking up from G3.
Change-Id: I39011a0846f042d224a7cd65f736e749acc8ec75
Signed-off-by: Hannah Williams <hannah.williams@intel.com>
Reviewed-on: https://review.coreboot.org/23221
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Fixes supports for flash ROMs larger than 512K, such as the 1M one in
HP t5550 Thin Client.
Change-Id: I4d6287e130809c33dfbd40bce7913a95b4b3a9c7
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Reviewed-on: https://review.coreboot.org/22262
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Similar to ACPI_GPIO_OUTPUT, this change provides ACPI_GPIO_INPUT_*
macros with ACTIVE_LOW and ACTIVE_HIGH polarity.
Change-Id: I77da6ad2f04d7f7bb6774df35105bdbe963d87d3
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/23235
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Change-Id: Ie5ff62ee1c7ca193ba841c5b2fb20940ec657625
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/21467
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
* Add IMX258 sensor entity
* Add DW9807 VCM control entity
* Enable CIO2 and IMGu in devicetree.cb
TEST: Verified the MIPI camera function on DUT board
Change-Id: Iebd41ac3631829bbb0b008761eb67c3db3e94638
Signed-off-by: Andy Yeh <andy.yeh@intel.com>
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/23056
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
|
|
Right now the poppy baseboard camera topology allows to add maximum of 2
sensors. The sensors can be of different vendors. The current ASL code
structure doesn't allow sensor customization. Moving PMIC specific objects
from sensor objects to PMIC scope and having separate sensor ASL files will
help in unbinding the PMIC and sensor objects and allow some customizations.
BUG=None
BRANCH=None
TEST=Build and boot soraka, make sure both camera's are working fine
and also verify that the generated DSDT looks fine.
Change-Id: I63ae1a685b78bda212c5c48a4c2dc744164a3cb5
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/23168
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
|
|
The variant boards can have a custom endpoints, splitting the ASL code
aids customizing the endpoints as per the variant board setup.
BUG=None
BRANCH=None
TEST=build boot soraka, verify that the cameras are working fine and
generated DSDT tables are same as before.
Change-Id: I5f1cded25bfb6a7baf18b211f9773dfecdc2f264
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/23167
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Rajmohan Mani <rajmohan.mani@intel.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
|
|
The deallocation was always subtracting the header, even when it
shouldn't. This caused problems for the allocator where buffer
sizes were incorrect and freed and used buffers could collide.
Fix the deallocation size.
Clear deallocated concatinated buffer header memory.
Fix the initial calculation of the total buffer size
available to be allocated.
BUG=b:71764350
TEST= Boot grunt.
BRANCH=none
Change-Id: I2789ddf72d662f24709dc5d9873741169cc4ef36
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/23284
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Boards that are still using LATE_CBMEM_INIT are being
removed as previously discussed.
If these boards are updated to not use LATE_CBMEM_INIT, they
can be restored to the active codebase from the 4.7 branch.
Removed boards:
amd/dinar
tyan/s2886
supermicro/h8scm
supermicro/h8qgi
Change-Id: I16be3b43fc0c48d58ed8b6667880c9571c6f5510
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/23274
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
This patch provides an option for non-chrome devices to make use of
FSP-T for performing cache-as-ram initialization. Majority of IOTG users
are using FSP-T for CAR implementation and aren't able to select FSP_CAR
Kconfig from SoC without conflicting with existing CAR config.
TEST=Ensure that both the Chrome platform and non Chrome OS platform
can select either CAR implementation based on Kconfig options
FSP_CAR or CAR_NEM_ENHANCED. By default Chrome platform choose
CAR_NEM_ENHANCED Kconfig and non Chrome platforms choose
FSP_CAR by default.
Change-Id: If565b649fe1c2abdbcf0a740c15db7253c084ae7
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/23161
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
According to CNL PCH BIOS spec (570374) 2.4.1, DMI cycle decoding needs
to be programmed before it gets locked. Update lpc programming to add
decode programming on DMI side as well. Also enabled io port 0x200
decoding by default.
BUG=b.70765863
TEST=Apply changes and add chromeos EC decoding in mainboard
devicetree.cb, then read back IO port in depthcharge cli and check
that return is not zero.
Change-Id: I6b8f393c92cbd0632fed86212ae384ff53c9f8c3
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/22970
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This patch sets the ACPI FADT flag ACPI_FADT_LOW_PWR_IDLE_S0
if S0IX is enabled for the platform.
TEST= Boot to OS and check the ACPI_FADT_LOW_PWR_IDLE_S0 flag
is set in FACP table.
Change-Id: Ibb43d5c8024dcdf753416e4bd2a457991cc7a433
Signed-off-by: Shaunak Saha <shaunak.saha@intel.com>
Reviewed-on: https://review.coreboot.org/23095
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
All boards and chips that are still using LATE_CBMEM_INIT are being
removed as previously discussed.
If these boards and chips are updated to not use LATE_CBMEM_INIT, they
can be restored to the active codebase from the 4.7 branch.
chips:
cpu/intel/socket_mFCBGA479
northbridge/intel/i82830
Mainboards:
mainboard/rca/rm4100
mainboard/thomson/ip1000
Change-Id: I9574179516c30bb0d6a29741254293c2cc6f12e9
Signed-off-by: Martin Roth <gaumless@gmail.com>
Reviewed-on: https://review.coreboot.org/22032
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
All boards and chips that are still using LATE_CBMEM_INIT are being
removed as previously discussed.
If these boards and chips are updated to not use LATE_CBMEM_INIT, they
can be restored to the active codebase from the 4.7 branch.
chips:
northbridge/intel/i3100
southbridge/intel/i3100
superio/intel/i3100
cpu/intel/socket_mPGA479M
Mainboards:
mainboard/intel/truxton
mainboard/intel/mtarvon
mainboard/intel/truxton
Change-Id: Ic2bbdc8ceb3ba0359c120cf4286b0c5b7dc653bb
Signed-off-by: Martin Roth <gaumless@gmail.com>
Reviewed-on: https://review.coreboot.org/22031
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
All boards and chips that are still using LATE_CBMEM_INIT are being
removed as previously discussed.
If these boards and chips are updated to not use LATE_CBMEM_INIT, they
can be restored to the active codebase from the 4.7 branch.
chips:
northbridge/intel/i5000
Mainboards:
mainboard/supermicro/x7db8
mainboard/asus/dsbf
Change-Id: I6614c0033b4439d196f26819998d3f85e6d11c00
Signed-off-by: Martin Roth <gaumless@gmail.com>
Reviewed-on: https://review.coreboot.org/22030
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
All boards and chips that are still using LATE_CBMEM_INIT are being
removed as previously discussed.
If these boards and chips are updated to not use LATE_CBMEM_INIT, they
can be restored to the active codebase from the 4.7 branch.
chips:
northbridge/intel/i855
Mainboards:
mainboard/lanner/em8510
Change-Id: Ic9ba0ba7e2b6e602a5749cc531dd705c49e3f08d
Signed-off-by: Martin Roth <gaumless@gmail.com>
Reviewed-on: https://review.coreboot.org/22029
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
All boards and chips that are still using LATE_CBMEM_INIT are being
removed as previously discussed.
If these boards and chips are updated to not use LATE_CBMEM_INIT, they
can be restored to the active codebase from the 4.7 branch.
chips:
soc/intel/sch
Mainboards:
mainboard/iwave/iWRainbowG6
Change-Id: Ida0570988a23fd0d13c6fcbe54f94ab0668c9eae
Signed-off-by: Martin Roth <gaumless@gmail.com>
Reviewed-on: https://review.coreboot.org/22027
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
All boards and chips that are still using LATE_CBMEM_INIT are being
removed as previously discussed.
If these boards and chips are updated to not use LATE_CBMEM_INIT, they
can be restored to the active codebase from the 4.7 branch.
chips:
soc/dmp/vortex86ex
Mainboards:
mainboard/dmp/vortex86ex
Change-Id: Iee7b6005cc2964b2346aaf4dbd9b2d2112b7403f
Signed-off-by: Martin Roth <gaumless@gmail.com>
Reviewed-on: https://review.coreboot.org/22026
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
All boards and chips that are still using LATE_CBMEM_INIT are being
removed as previously discussed.
If these boards and chips are updated to not use LATE_CBMEM_INIT, they
can be restored to the active codebase from the 4.7 branch.
chips:
cpu/amd/geode_gx2
northbridge/amd/gx2
southbridge/amd/cs5535
Mainboards:
mainboard/amd/rumba
mainboard/lippert/frontrunner
mainboard/wyse/s50
Change-Id: I81c130f53bbfa001edbfdb7a878ef115757f620c
Signed-off-by: Martin Roth <gaumless@gmail.com>
Reviewed-on: https://review.coreboot.org/22025
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
BUG=b:71838954
TEST=
1. emerge-nami coreboot chromeos-bootimage
2. check touchpad function
3. evtest
/dev/input/event5: Elan Touchpad
Change-Id: I14471d1473a3b3ecf15aaf362b47874704cd3bf0
Signed-off-by: van_chen <van_chen@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/23133
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Some Dock events only need to happen based on the Dock Id (which
functions as a presence detect GPIO).
Inspired by vendor bios DSDT.
This fixes undock ACPI events being issued when pulling out the power
when docked or undocked (but still generates one when forcibly
undocked)
Tested on X200: pull power and see if undock events are generated in
dmesg.
Change-Id: I1eef971d49508bcd94d5d1cf2b70395b7cd80b1c
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/22919
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kevin Keijzer <kevin@quietlife.nl>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
If the DRAM does *not* actually overlap the PCI space, the remap code
notices it is the case, but for some reason proceeds with the remapping,
attempting to remap a negatively sized chunk. Bummer.
With a single 1024M (two ranks of 512M) module:
Nothing to remap
Mem remapping enabled
Remapstart 5120(MB)
Remapend 6144(MB)
Top of RAM 1024MB
New top of RAM 2560MB
Wrote remap map a0101
Mem remapping enabled
Remapstart 4096(MB)
Remapend 2560(MB)
New top of memory is at 2560MB
Needless to say, subsequent ram_resource() ruins the memory map for the
OS -- Linux won't boot without a mem= argument and memtest quickly.
TEST=memtest and Linux boot on HP t5550 with 1024M of memory
Change-Id: Ic221723a26c5d1a03bf34c7722b0abe115f456ba
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Reviewed-on: https://review.coreboot.org/22271
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
This is required for Flashrom to work well.
Change-Id: Id756d86a7f3b34f816ea7a7ed78f159512f550d5
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Reviewed-on: https://review.coreboot.org/22258
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Change-Id: I990969cf1389c19032c4a0fafbdef45b9d6d1e8b
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Reviewed-on: https://review.coreboot.org/22257
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Change-Id: Ic02c3a6265f11c1571369bc04371d28b6f989736
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/21464
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This source file was mostly copied from ga-945gcm-s2l but had
different IO decode ranges.
Change-Id: I54cb165000fad6984edf13fb33519fb9c9f0350f
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/23134
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Things cleaned up in this patch:
* Add macros for the GENx_DEC registers;
* replace many magic numbers by macros;
* remove many writes to DxxIP since they were 'setting' reset default
values;
* fix some comments about decode ranges.
Change-Id: I9d6a0ff3d391947f611a2f3c65684f4ee57bc263
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/21065
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Use the variable `device` instead of `dev` in the predicate of
the if condition, as `dev` is not changed in the for loop.
The for loop was added in the following commit.
commit 8fed77ae4c46122859d0718678e54546e126d4bc
Author: Scott Duplichan <scott@notabs.org>
Date: Sat Jun 18 10:46:45 2011 -0500
ASRock E350M1: Configure SB800 GPP ports to support onboard pcie nic
Reviewed-on: http://review.coreboot.org/44
The assumption that the devices are ordered in the tree seem to
hold in this case (although it is not ensured) and therefore at
least with the ASRock E350M1 no (visible) change is experienced as
the children are all of type `DEVICE_PATH_PCI`.
Change-Id: Iaa2fa13305dbe924965d27680cd02fe30c2f58a5
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/2562
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add code to support the board ASUS AM1I-A. Tested with multiple payloads
and OSes with satisfactory results. S3 suspend/resume works fine with
Linux but has issues with Windows (an exception is thrown). However,
after manually rebooting, Windows resumes the suspended session.
* Tested with: SeaBIOS 1.11 + Linux 4.10 - OK
* Tested with: tianocore vEDK2017 + MS Windows 8.1 - OK
* Tested with: FILO 0.6.0 - hangs after showing the banner
Details are going to be published on the board's status page.
Change-Id: I3d9432849560df81536bbb2ce4c87cd265b820f7
Signed-off-by: Gergely Kiss <mail.gery@gmail.com>
Reviewed-on: https://review.coreboot.org/23002
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
GPIO 90 is being used as a GPIO. The IOMUX register is set correctly,
but these additional registers need to be set to use it as a GPIO.
- Split structures into variant specific versions. These will be
moved into the variant tree in a follow-on patch
- Set GENINT_DISABLE bit
- Disable interrupts for this GPIO.
BUG=b:71867096
TEST=Build and boot grunt. Verify registers are set correctly.
Change-Id: I4b8d12720167b298ee6e0acf80edf414539975b0
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/23228
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=b:71867096
TEST=None
Change-Id: Ic8111d34355e6667c37a51d285ebb50c1659f4e5
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/23227
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
