| Age | Commit message (Collapse) | Author |
|---|
|
The differential signal of DQS needs to keep low
level before gate training. RPULL will connect
4Kn from PADP to VSS and a 4Kn from PADN to
VDDQ to ensure it. But if it has PHY side ODT
connected at this time, it will change the DQS
signal level. So it needs to disable PHY side ODT
when doing gate training.
BRANCH=None
BUG=None
TEST=boot from bob
Change-Id: I56ace8375067aa0bb54d558bc28172b431b92ca5
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Original-Commit-Id: cb024042c7297a6b17c41cf650990cd342b1376f
Original-Change-Id: I33cf743c3793a2765a21e5121ce7351410b9e19d
Original-Signed-off-by: Lin Huang <hl@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/448278
Original-Commit-Ready: Caesar Wang <wxt@rock-chips.com>
Original-Tested-by: Caesar Wang <wxt@rock-chips.com>
Original-Reviewed-by: Derek Basehore <dbasehore@chromium.org>
Reviewed-on: https://review.coreboot.org/18582
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
The previous implementation was using a for loop. By it's
very definition the last statement in the for loop declaration
is done at the end of the loop. Therefore, if the conditional for
breaking out of the for loop because of a timeout would always
see a value of 0 for the number of APs accepted. Correct this
by changing to a while loop with an explicit timeout condition
at the end of the loop.
Change-Id: I503953c46c2a65f7e264ed49c94c0a46d6c41c57
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/20225
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This patch uses common SCS library to setup
sd card.
Change-Id: I06898e30a9b39f169b35f581a3ee09238f0f40c4
Signed-off-by: Bora Guvendik <bora.guvendik@intel.com>
Reviewed-on: https://review.coreboot.org/20217
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Philippe Mathieu-Daudé <philippe.mathieu.daude@gmail.com>
|
|
This patch uses common SCS library to setup
sd card.
Change-Id: Iafbba04d7a498b9a321e8efee4abf07820d17330
Signed-off-by: Bora Guvendik <bora.guvendik@intel.com>
Reviewed-on: https://review.coreboot.org/19632
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philippe Mathieu-Daudé <philippe.mathieu.daude@gmail.com>
|
|
Create Intel Common SCS code. This code currently only contains
the code for SD card SSDT generation. More code will get added up
in the subsequent phases.
Change-Id: I82f034ced64e1eaef41a7806133361d73b5009d3
Signed-off-by: Bora Guvendik <bora.guvendik@intel.com>
Reviewed-on: https://review.coreboot.org/19631
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philippe Mathieu-Daudé <philippe.mathieu.daude@gmail.com>
|
|
Use verb table values from AMI firmware, consolidate NID
definitions using azalia macros. Fixes headphone jack detection
and microphone.
Change-Id: Ia31be6efc7afe921ad91b400f66694d951f0a260
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/19944
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Initialize the audio codec without depending on DSP binary blobs.
The hda_verb.c was copied from the intel/kblrvp rvp7 variant, and the
hda_verb.h file was copied from the purism/librem13.
The IoBufferOwnership FSP option in devicetree has to be 0 for the azalia
driver to work.
Change-Id: Ifa36ac0839daedfa59c497057da0ace04d401f2a
Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm>
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/19943
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Some NVMe devices (Intel 600p series for example) seem to lock up
in D3 drive power state (L1.2 PCIe power state).
Disabling L1 substates fixes it.
Change-Id: I00a327dc91d443beb565fe4e72aaf816e40a007c
Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm>
Reviewed-on: https://review.coreboot.org/19900
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Change-Id: I88e376d61c4aba5030a0be7c8bdfe7b57881a197
Signed-off-by: Hannah Williams <hannah.williams@intel.com>
Reviewed-on: https://review.coreboot.org/20169
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Enable libgfxinit.
Tested on Lenovo T430:
* LVDS
* VGA
* DP (using DP->HDMI adapter)
All three ports are working. The LVDS port is garbled under linux
when VGA or DP is connected, likely due to missing VBT.
Change-Id: I665661e93724072d1e8412cfcc0e818f824c8cb0
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/20117
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Use a GNVS variable to store the trackpad interrupt, in order to
support both SNB and IVB variants from a single build.
Change-Id: I53df35fff41f52a7d142aea9b1b590c65195bcfd
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/20093
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Add a GNVS variable to store trackpad IRQ for google/parrot, so
that both SNB and IVB variants can be built with the same config
Change-Id: I232da4077e3400b8ef2520dc33fd770c731b7ec3
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/20092
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Existing value was copied from librem13 v1 board, use value
obtained from AMI firmware.
TEST: Observe Windows boots correctly, function keys work
under both Windows and Linux.
Change-Id: I0ea6cc4602ce1047cb803acc65cbca1af1f480b0
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/19945
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Populate a memory_info struct with PEI and SPD data,
in order to inject the CBMEM_INFO table necessary to
populate a type17 SMBIOS table.
On Broadwell, this is done by the MRC binary, but the older
Haswell MRC binary doesn't populate the pei_data struct with
all the info needed, so we have to pull it from the SPD.
Some values are hardcoded based on platform specifications.
Change-Id: Iea837d23f2c9c1c943e0db28cf81b265f054e9d1
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/19958
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Add default values for MAINBOARD_VERSION and CBFS_SIZE.
Change-Id: Ib6461cef78f3fea448baf1ada456e3c8335f1543
Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm>
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/19942
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Youness Alaoui <snifikino@gmail.com>
|
|
- remove unused I2C, serialIO defs
- set PL2 override, VR mailbox cmd based on SKL-U ref board,
as values copied from google/chell are for SKL-Y
Change-Id: I3a138c28d0322df6cb41ec1a845ae31602cb69a7
Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm>
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/19941
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Update devicetree USB config based on board spec.
Leave OC pins set to skip since the info is unavailable.
Change-Id: I2a4fe17ed7edacbbbaf56969f9d2801b45a20da9
Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm>
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/19940
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Don't allow the user to set PCIe configspace base address.
Don't allow the user to set the DCACHE size and base.
Change-Id: I7a42cc5f6098214364624bcfa3cbd93b4903ee84
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/20181
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
|
|
Change-Id: Ic1656311ecc670dc0436995f0ec8199d270da4d1
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/20180
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Philippe Mathieu-Daudé <philippe.mathieu.daude@gmail.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
|
|
Change-Id: I8b2794f56f39492589a08e5676cb33eec89a976e
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/20179
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
|
|
Change-Id: I254549057552be93611afa8ca52d22be220fe3dc
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/20178
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Philippe Mathieu-Daudé <philippe.mathieu.daude@gmail.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
|
|
Does not need to changeable in menuconfig.
Change-Id: Id488f7333952d10d10a62ac75298ec8008e6f9b4
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/20177
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
|
|
While building poppy board, build failed with following error message:
Writing new image to build/coreboot.pre.new
mv build/coreboot.pre.new build/coreboot.pre
util/me_cleaner/me_cleaner.py -c build/coreboot.pre > /dev/null
This image does not contains a ME/TXE firmware NR = 0)
make: *** [src/southbridge/intel/common/firmware/Makefile.inc:55:
add_intel_firmware] Error 1
Hence keeping CHECK_ME unset by default.
TEST=Succesfully built coreboot for Poppy & booted to OS.
Change-Id: Ib3186498c8da307b686c06c3828e24acbc7f2d17
Signed-off-by: Naresh G Solanki <naresh.solanki@intel.com>
Reviewed-on: https://review.coreboot.org/19257
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nicola Corna <nicola@corna.info>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
The board dutifully registers an int15h handler and provides the
defaults to add a VGABIOS.
That should be good enough to initialize graphics through the VGABIOS
file.
Fixes build on Chrome OS configurations (at least until the Ada toolchain
situation is resolved over there).
Change-Id: I1d956b5a163b7cdf2bd467197fba95f16e5e8fa3
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/20218
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
|
|
As the hardware designed on gru, the AP_I2C_TP_PU_EN (gpio3_b4) controlled
the SCL/SDA status to avoid leakage. And the gpio3_b4 of rk3399 pull
resistor is 26k~71k and 3.3v for supply power, and gpio3_b4 pin connected
2.2k resistor to i2c of TP device.
The default of this gpio status is pulled up during the start to bootup,
it's very weak drive for the TP device that maybe cause to trigger the
recovery process of elan's firmware.
Also, the Elan updated its firmware(102.0.5.0) to delay checking the
i2c of touchpad is greater than 1 second.
So we have to drive the stronger pull-up within 1 second of powering up
the touchpad to prevent its firmware from falling into recovery.
Change-Id: I9a67d1c041afafde24ed9f00716ba41a9b41a8da
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Reviewed-on: https://review.coreboot.org/19863
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Use common init_igd_opregion method and remove duplicated code in
acpi.c.
Change-Id: I811e8bd2be68813321dc4581af02e1c21b0da076
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/19910
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Add method gma_write_acpi_tables.
No need to update GNVS as it doesn't have ASLB.
Change-Id: Ia138cfde2271a298c36b85e999ff69f0f211ba11
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/19909
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
This reverts commit f4835a85c0e851d13bcfed53a23f495caeefe8e2. It
completely ignores port coalescing and breaks enumeration in many
cases. The code reused to disable and hide the root ports was never
meant to be called that way.
The same effect of power saving can likely be achieved by clock
gating unused ports after enumeration without further, error-prone
function hiding.
Change-Id: I90d8b9236004f0c42d5a2b6bbd39f6dea07bd3d1
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/20216
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
This driver reinvented MAINBOARD_DO_NATIVE_VGA_INIT in a very special
way: If it wasn't set, perform native gfx init in textmode, if it was
set, perform native gfx init in linear framebuffer mode. Test for
LINEAR_FRAMEBUFFER instead and make the native gfx init optional.
Also, make Kconfig reflect the actual behaviour.
Change-Id: If20fd1f5b0f4127b426e8ff94acc61fcd4eb49af
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/20131
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
This was the single spot where VGA_BIOS_ID wasn't guarded by anything.
It resulted in the wrong default id if we didn't chose to add a VGA BIOS
at first but added one later (e.g. a board provided default guarded by
VGA_BIOS wasn't applied then, because the Via/CN700 value was already
set).
Change-Id: Ia16a5e6d194191d8da8c551d6eb3849bc65864a9
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/20101
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
A major regression was introduced with commit 6520e01a
(soc/intel/apollolake: Perform CPU MP Init before FSP-S Init)
where the APs execution context is taken away by FSP-S. It
appears that FSP-S is not honoring the SkipMpInit UPD because
it's been shown with some debug code that FSP-S is compeltely
hijacking the APs:
Chrome EC: Set WAKE mask to 0x00000000
Chrome EC: Set WAKE mask to 0x00000000
CBFS: 'VBOOT' located CBFS at [440000:524140)
CBFS: Locating 'vbt.bin'
CBFS: Found @ offset 2e700 size 1a00
Running FSPS in 4 secs.. 315875 4315875
cpu2 Waiting for work
cpu3 Waiting for work
cpu1 Waiting for work
cpu2 Waiting for work
cpu3 Waiting for work
cpu1 Waiting for work
cpu2 Waiting for work
cpu3 Waiting for work
cpu1 Waiting for work
cpu2 Waiting for work
cpu3 Waiting for work
cpu1 Waiting for work
cpu2 Waiting for work
cpu3 Waiting for work
cpu1 Waiting for work
cpu2 Waiting for work
cpu3 Waiting for work
cpu1 Waiting for work
cpu2 Waiting for work
cpu3 Waiting for work
cpu1 Waiting for work
cpu2 Waiting for work
cpu3 Waiting for work
cpu1 Waiting for work
Running FSPS.. 4315875 4315875
ITSS IRQ Polarities Before:
ITSS IRQ Polarities Before:
IPC0: 0xffffeef8
IPC1: 0xffffffff
IPC2: 0xffffffff
IPC3: 0x00ffffff
ITSS IRQ Polarities After:
IPC0: 0xffffeef8
IPC1: 0x4a07ffff
IPC2: 0x08000000
IPC3: 0x00a11000
This is essentially a revert of 6520e01a to fix the previous
behavior.
Change-Id: I2e136ea1757870fe69df532ba615b9bfc6dfc651
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/20215
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Andrey Petrov <andrey.petrov@intel.com>
|
|
Use common init_igd_opregion method.
Change-Id: Ia10a28d05b611a59f787b53f9736b3b76a19ea4a
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/19908
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Use common init_igd_opregion method.
Change-Id: Ic8a85d1373f04814b4460cce377d6e096bcdc349
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/19907
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Too low gfx_uma_size can result in problems if the framebuffer
does not fit.
This partially reverts: 7afcfe0 "gm45: enable setting all vram sizes
from cmos"
Change-Id: I485d24198cb784db5d2cfce0a8646e861a4a1695
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/20194
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Commit 2e7f6cc introduced the 'no graphics init' option for
FSP 1.1 SoCs using a GOP driver to init the display, but selecting
that option while including a VBT breaks compilation for Braswell
and Skylake devices because the VBT and GOP driver are intertwined.
This patch decouples the VBT from the GOP driver execution,
allowing the 'no graphics init' option to compile (and work)
properly when CONFIG_ADD_VBT_DATA_FILE=y.
Change-Id: Ifbcf32805177c290c4781b32bbcca679bcb0c297
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/20210
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Youness Alaoui <snifikino@gmail.com>
|
|
TEST=Verified that board still boots to OS without any error.
Change-Id: I02d2a6cbcab92766a35993bfd20aaeed4ca22c90
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/20143
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Now that we dynamically disable TPM interface based on config options,
add support for generation of SPI TPM ACPI node if SPI TPM is used.
Change-Id: I87d28a42b48ba916c70e45a061c5efd91a8a59bf
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/20142
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Based on the config options selected, decide at runtime which TPM
interface should be disabled so that ACPI tables are not generated for
that interface.
TEST=Verified that unused interface does not show up in ACPI tables.
Change-Id: Iee8f49e484ed024c549f60c88d874c08873b75cb
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/20141
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philippe Mathieu-Daudé <philippe.mathieu.daude@gmail.com>
|
|
Change-Id: Ib7aa495ccfd405d6ffc968388c28dc540da2f525
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/20203
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
If I2C device is disabled:
1. BAR for the device will be 0
2. There is no need to generate ACPI tables for the device
TEST=Verified that if an i2c device is disabled statically in
devicetree or dynamically in mainboard, then coreboot does not die
looking for missing resources.
Change-Id: Id9a790e338a0e6f32c199f5f437203e1525df208
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/20140
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Philippe Mathieu-Daudé <philippe.mathieu.daude@gmail.com>
|
|
Initial support for undefined behavior sanitizer in ramstage. Enabling
this will add -fsanitize=undefined to the compiler command line and
link with ubsan.c in ramstage. Code with UB triggers a report with
error, file, and line number, then aborts.
Change-Id: Ib139a418db97b533f99fc59bcb1a71fb6dcd01d8
Signed-off-by: Ryan Salsamendi <rsalsamendi@hotmail.com>
Reviewed-on: https://review.coreboot.org/20156
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
|
|
Fixes report found by undefined behavior sanitizer. Left shifting an int
where the right operand is >= width of type is undefined. Add
ul suffix since it's safe for unsigned types.
Change-Id: I4b2365428e421085285006bc1ea8aea75890ff65
Signed-off-by: Ryan Salsamendi <rsalsamendi@hotmail.com>
Reviewed-on: https://review.coreboot.org/20144
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Philippe Mathieu-Daudé <philippe.mathieu.daude@gmail.com>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Youness Alaoui <snifikino@gmail.com>
|
|
Fixes report found by undefined behavior sanitizer. Dereferencing a
pointer that is not aligned to the size of access is undefined behavior.
Switch to memcpy() for unaligned write to EBDA_LOWMEM. Change other
write16()s in setup_ebda() to memcpy() for consistency.
Change-Id: I79814bd47a14ec59d84068b11d094dc2531995d9
Signed-off-by: Ryan Salsamendi <rsalsamendi@hotmail.com>
Reviewed-on: https://review.coreboot.org/20132
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Philippe Mathieu-Daudé <philippe.mathieu.daude@gmail.com>
|
|
USB port status register can be used to decide if a particular port
was responsible for generating PME# resulting in device wake:
1. CSC bit is set and port is capable of waking on connect/disconnect
2. PLC bit is set and port is in resume state
BUG=b:37088992
TEST=Verified with wake on USB2.0 port 3, mosys shows:
19 | 2017-06-08 15:43:30 | Wake Source | PME - XHCI (USB 2.0 port) | 3
Change-Id: Ie4fa87393d8f096c4b3dca5f7a97f194cb065468
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/20122
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Also changes the arguments of some functions to const.
This reduces romstage size by a whopping 1009 bytes.
Change-Id: I054504412524b7be19d98081097843b61bc0c459
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/20147
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Ryan Salsamendi <rsalsamendi@hotmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Philippe Mathieu-Daudé <philippe.mathieu.daude@gmail.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
|
|
There are many good reasons why we may want to run some sort of generic
callback before we're executing a reset. Unfortunateley, that is really
hard right now: code that wants to reset simply calls the hard_reset()
function (or one of its ill-differentiated cousins) which is directly
implemented by a myriad of different mainboards, northbridges, SoCs,
etc. More recent x86 SoCs have tried to solve the problem in their own
little corner of soc/intel/common, but it's really something that would
benefit all of coreboot.
This patch expands the concept onto all boards: hard_reset() and friends
get implemented in a generic location where they can run hooks before
calling the platform-specific implementation that is now called
do_hard_reset(). The existing Intel reset_prepare() gets generalized as
soc_reset_prepare() (and other hooks for arch, mainboard, etc. can now
easily be added later if necessary). We will also use this central point
to ensure all platforms flush their cache before reset, which is
generally useful for all cases where we're trying to persist information
in RAM across reboots (like the new persistent CBMEM console does).
Also remove cpu_reset() completely since it's not used anywhere and
doesn't seem very useful compared to the others.
Change-Id: I41b89ce4a923102f0748922496e1dd9bce8a610f
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/19789
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
If an MTRR solution exceeds the number of available MTRRs
don't attempt to commit the result. It will just GP fault
with the MSR write to an invalid MSR address.
Change-Id: I5c4912d5244526544c299c3953bca1bf884b34d5
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/20163
Reviewed-by: Youness Alaoui <snifikino@gmail.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philippe Mathieu-Daudé <philippe.mathieu.daude@gmail.com>
|
|
AMD_FAM10H code enables early cbmem by default.
Change-Id: Ifad007f6604bb612d544cf1387938a8fef1cceb4
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/20148
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Philippe Mathieu-Daudé <philippe.mathieu.daude@gmail.com>
|
|
Since this mainboard provides 3 COM ports on LPC, enable decoding of the
corresponding address range for COM 3.
Change-Id: I15c0748fce67eef46401c314f441aa45f5e3c5fa
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/20162
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
The 'set' field was not used anywhere. Replace the struct with a simple
integer representing the mask.
initializer updates performed with:
sed -i -r 's/\{ ?0(x([[:digit:]abcdefABCDEF]{3,4}))?, (0x)?[04]? ?\}/0\1/g' \
src/ec/*/*/ec.c
sed -i -r 's/\{ ?0(x([[:digit:]abcdefABCDEF]{3,4}))?, (0x)?[04] ?\}/0\1/g' \
src/ec/*/*/ec_lpc.c \
src/superio/*/*/superio.c \
src/superio/smsc/fdc37n972/fdc37n972.c \
src/superio/smsc/sio10n268/sio10n268.c \
src/superio/via/vt1211/vt1211.c
src/ec/kontron/it8516e/ec.c was manually updated. The previous value for
IT8516E_LDN_SWUC appears to have been a typo, as it was out of range and
had a zero bit in the middle of the mask.
Change-Id: I1e7853844605cd2a6d568caf05488e1218fb53f9
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-on: https://review.coreboot.org/20078
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Myles Watson <mylesgw@gmail.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
- use Siemens NC FPGA driver for backlight brightness and PWM control
- set Dsave time for board reset after falling edge of signal xdsave
Change-Id: I5077d4af162e54a3993e5e0d784a8356f51bd0c9
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/20161
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
The siemens/mc_apl1 mainboard needs more functionality provided by
Siemens NC FPGA. The additional functionality contains backlight
brightness/PWM control and Dsave time for board reset.
Change-Id: I6b65b01f0d67afe598b7c005868f71b00dec56fd
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/20160
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
The Siemens mc_apl1 mainboard needs new values from hwilib.
- add Dsave time for board reset
- add backlight brightness for panel setting
- add backlight PWM period
Change-Id: I3a48654ef57c7f8accaabe60e8aec144e4fe5466
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/20159
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Change-Id: I558e6c63caf95ec5279ec5a866b54fb199116469
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/19678
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Philippe Mathieu-Daudé <philippe.mathieu.daude@gmail.com>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
The previous code seemed weird and tried to check if its selected
value is supported three times.
This also lower the clock if a selected frequency does not result in a
supported CAS number.
Change-Id: I1df20a0a723dc515686a766ad1b0567d815f6e89
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/19717
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
The previous code seemed weird and tried to check if its selected
value is supported three times.
This also lower the clock if a selected frequency does not result in a
supported CAS number.
Change-Id: I97244bc3940813c5a5fcbd770d71cca76d21fcae
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/19716
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
Fix line over 80 characters, spaces required around comparisons,space
required after close brace '}', comma ',', semicolon ';', space
prohibited after ')' errors and warnings
Change-Id: I5585f55a606d4f2149b17ac92cbdd832f242630e
Signed-off-by: Evelyn Huang <evhuang@google.com>
Reviewed-on: https://review.coreboot.org/20099
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Based on the Intel G41 chipset, ICH7 southbridge, and IT8720F Super I/O.
Tested, working:
* Booting Linux 4.11.3 and Windows 8.1 from USB and HDD
* Resume from S3 (Linux and Windows)
* Native raminit (DDR2-800)
* Native graphics init (SeaBIOS, Linux)
* Graphics init with VGA BIOS (SeaBIOS, Windows)
* PCI-E x16 PEG slot, PCI-E x1 slot from southbridge
* Realtek ALC888 HD Audio (including front panel and jack detection)
* Realtek R8168 Gigabit LAN
* Both SATA ports
* USB 1.1 and 2.0 devices (keyboard, mass storage)
* PC speaker beep
* COM header
* Super I/O Environment controller (temps, voltage, fans)
* PS/2 keyboard and mouse
* Flashing with `flashrom -p internal`
* 1MiB and 2MiB SPI flash chips
* CMOS gfx_uma_size
Appears, OS driver loads, but otherwise untested:
* IrDA header
* CIR header
* TPM header
Untested:
* S/PDIF digital audio
Tested, known broken:
* CMOS power_on_after_fail
* USB keyboard in secondary payloads
Change-Id: Ifc4c8935b1a11e55f4bf6cfa484a8a8d09b1adda
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-on: https://review.coreboot.org/20027
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Test: boot OS (Ubuntu, Windows 10) on librem13v2, verify BT
function key toggle now works correctly.
Change-Id: I68dc99e72a09f7affbcd691d03dd4607a898313e
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/19897
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Youness Alaoui <snifikino@gmail.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
I updated my spike patch[1] to cleanly apply to current spike master.
As a side effect, the UART is now at 0x02100000.
[1]: https://github.com/riscv/riscv-isa-sim/pull/53
Change-Id: I4cb09014619e230011486fa57636abe183baa4be
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/20126
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Fix line over 80 characters, unnecessary braces for single statement
blocks, spaces before close parantheses errors and warnings.
Signed-off-by: Evelyn Huang <evhuang@google.com>
Change-Id: I31b1932a2c1e401e56751e0c790bcc6287fb550d
Reviewed-on: https://review.coreboot.org/20097
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Fix space prohibited between function name and open parenthesis, line
over 80 characters, unnecessary braces for single statement blocks,
space required before open brace errors and warnings
Change-Id: I66f1a8640ec5c9d8a1dd039088598f40e8d30f95
Signed-off-by: Evelyn Huang <evhuang@google.com>
Reviewed-on: https://review.coreboot.org/20096
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Some of these can be changed from #if to if(), but that will happen
in a follow-on commmit.
Change-Id: I5a674cd7a360a0dd040c859ec1f8d760d7c83364
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/20130
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Change-Id: Id88455f2c7c28e0b298675b9af2a39361759a34a
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/19120
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Change-Id: I1c4b30ab47e12ec35cb681ec5c6635ecd20aa2e5
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/19121
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
For an unknown reason, the I2C ACPI devices were placed
under \SB intead of \SB.PCI0, as with all other non-Atom
based Intel platforms. While Linux is tolerant of this,
Windows is not. Correct by moving I2C ACPI devices where
they belong.
Also, adjust I2C devices at board level for google/rambi
as to not break compilation.
Change-Id: I4ef978214aa36078dc04ee1c73b3e2b4bb22f692
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/20056
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
This device is extremely similar to the IT8718F, so support is based on
existing support for the IT8718F. The CIR device is only detected by
Linux/Windows from the ACPI tables, so ACPI support is extended from the
IT8783E/F (for ACPI). This Super I/O is used on the Foxconn G41S-K.
Tested, working:
* Serial port 1
* Environment controller
- Temperature monitoring
- Voltage monitoring
- Fan control (automatic and manual)
* PS/2 keyboard and mouse
Appears, OS driver loads, but otherwise untested:
* Serial port 2
* Consumer IR
Untested:
* Floppy controller
* Parallel port
* GPIO
Change-Id: Ib9a6fe91a772d78f4d122a6c516feff8658ada0a
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-on: https://review.coreboot.org/20026
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Change-Id: Ifcbf95ffd6d13cae4e6864e0320ce6ce1cf3ae4d
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-on: https://review.coreboot.org/20025
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philippe Mathieu-Daudé <philippe.mathieu.daude@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Change-Id: Id4a079d868c5c806c769b5559833566e8a6a8a71
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-on: https://review.coreboot.org/20077
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Some Super I/O PnP devices are detected by string matching the hardware
ID. Allow providing a custom HID to override the default generic one.
Change-Id: I7793b7d53c9d94667675f9dee63358521ac8c4be
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-on: https://review.coreboot.org/20076
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Some Super I/O logical devices have three I/O port ranges, such as the
GPIO on the IT8720F. Allow specifying a third I/O range. While here, fix
a typo in the I/O range description.
Change-Id: Idad03f3881e0fbf2135562316d177972f931afec
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-on: https://review.coreboot.org/20024
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
BUG=b:37088992
Change-Id: If0b495234d6e498d5c64ba4dd186440cd7a1c5c6
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/20121
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
With change dd82edc388 (lib/spd_bin: make SMBus SPD addresses an
input), SMBus SPD addresses are accepted from the mainboard and not
calculated within the spd_bin library routines. Use the addr_map
values to print correct address in dump_spd_info.
Change-Id: Iff37e382aeac9704f74bafc2ecb27f14c478723f
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/20118
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shelley Chen <shchen@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This patch makes SOC files to use common/block/cpu/cpulib.c
file's helper functions.
Change-Id: I529c67cf20253cf819d1c13849300788104b083c
Signed-off-by: Barnali Sarkar <barnali.sarkar@intel.com>
Reviewed-on: https://review.coreboot.org/19827
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The supported "G41C-GS" with a nuvoton nct6776 superio is actually
G41C-GS R2.0, which is different with the more easily-found revision
G41C-GS (R1.0) with Winbond W83627DHG superio, and should be ported
separately.
Photos for the two revision:
R1.0: https://web.archive.org/web/20160915160553/http://www.asrock.com/mb/photo/G41C-GS(L1).jpg
R2.0: https://web.archive.org/web/20160717203810/http://www.asrock.com/mb/photo/G41C-GS%20R2.0(L2).jpg
Change-Id: If60a694bcf0652ab32c0ac75ceec7e27e11fe9eb
Signed-off-by: Bill XIE <persmule@gmail.com>
Reviewed-on: https://review.coreboot.org/19980
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Rename these two Macros to help use Common Code -
ACPI_PMIO_BASE --> ACPI_BASE_ADDRESS
ACPI_PMIO_SIZE --> ACPI_BASE_SIZE
Change-Id: I21125b7206c241692cfdf1cdb10b8b3dee62b24a
Signed-off-by: Barnali Sarkar <barnali.sarkar@intel.com>
Reviewed-on: https://review.coreboot.org/20038
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch enables ACPI timer emulation on all the logical cpus.
BUG=chrome-os-partner:62438
BRANCH=NONE
TEST=Verify MSR 0x121 gets programmed on all logical cpus during coreboot MP Init.
Change-Id: I2246cdfe1f60fd359b0a0eda89b4a45b5554dc4a
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/18288
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch makes SOC files to use common/block/cpu/cpulib.c
file's helper functions.
Change-Id: I6af56564c6f488f58173ba0beda6912763706f9f
Signed-off-by: Barnali Sarkar <barnali.sarkar@intel.com>
Reviewed-on: https://review.coreboot.org/19566
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Create Intel Common CPU library code which provides various
CPU related APIs.
This patch adds cpulib.c file which contains various helper
functions to address different CPU functionalities like -
cpu_set_max_ratio(),
cpu_get_flex_ratio(),
cpu_set_flex_ratio(),
cpu_get_tdp_nominal_ratio(),
cpu_config_tdp_levels(),
cpu_set_p_state_to_turbo_ratio(),
cpu_set_p_state_to_nominal_tdp_ratio(),
cpu_set_p_state_to_max_non_turbo_ratio(),
cpu_get_burst_mode_state(),
cpu_enable_burst_mode(),
cpu_disable_burst_mode(),
cpu_enable_eist(),
cpu_disable_eist(),
cpu_enable_untrusted_mode()
Change-Id: I2f80c42132d9ea738be4051d2395e9e51ac153f8
Signed-off-by: Barnali Sarkar <barnali.sarkar@intel.com>
Reviewed-on: https://review.coreboot.org/19540
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
|
|
As per BWG, CPU MP Init (loading ucode) should be done prior
to BIOS_RESET_CPL. Hence, pull MP Init to BS_DEV_INIT_CHIPS Entry
(before FSP-S call).
BUG=none
BRANCH=none
TEST=Build and boot Reef
Change-Id: I49f336c10d6afb71f3a3b0cb8423c7fa94b6d595
Signed-off-by: Barnali Sarkar <barnali.sarkar@intel.com>
Reviewed-on: https://review.coreboot.org/20037
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Since get_microcode_info() is aleady searching for the microcode in cbfs,
we can just add a intel_microcode_load_unlocked() call here to update
the microcode. No need to duplicate finding microcode step during
pre_mp_init() function.
Change-Id: I525cab0ecc7826554f0a1209862e6357d1c7a9a6
Signed-off-by: Barnali Sarkar <barnali.sarkar@intel.com>
Reviewed-on: https://review.coreboot.org/20088
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
|
|
FIT is already loading microcode before CPU Reset. So, we need
not update the microcode again in RO FW in bootblock.
But we need to update in RW FW if there is any new ucode version.
So, added the update microcode function in get_microcode_info callback
before MP Init to make sure BSP is using the microcode from cbfs.
BUG=none
BRANCH=none
TEST=Build and Boot poppy
Change-Id: I5606563726c00974f00285acfa435cadc90a085e
Signed-off-by: Barnali Sarkar <barnali.sarkar@intel.com>
Reviewed-on: https://review.coreboot.org/20051
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
|
|
If the boot media is memory mapped temporarily mark it as write
protect MTRR type so that memory-mapped accesses are faster.
Depthcharge payload loading was sped up by 75ms using this.
Change-Id: Ice217561bb01a43ba520ce51e03d81979f317343
Signed-off-by: Barnali Sarkar <barnali.sarkar@intel.com>
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/20089
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
The fast_spi_cache_bios_region() does the necessary lookup
of BIOS region size, etc. Don't inline the calculation and
just defer to the common piece of code for memory-mapped
spi flash boot.
Change-Id: I6c390aa5a57244308016cd59679d8c3ab02031b8
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/20116
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Barnali Sarkar <barnali.sarkar@intel.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
After the MTRR solution has been calculated provide a way
for code to call the same function, fast_spi_cache_bios_region(),
in all stages. This is accomplished by using the ramstage
temporary MTRR support.
Change-Id: I84ec90be3a1b0d6ce84d9d8e12adc18148f8fcfb
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/20115
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Barnali Sarkar <barnali.sarkar@intel.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Like the previous commit allow the declarations of functions to
be exposed to all stages unless ROMCC is employed.
Change-Id: Ie4dfc32f38890938b90ef8e4bc35652d1c44deb5
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/20114
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Fix line over 80 characters warnings and space after function name
warning.
Change-Id: Id5a5abaa06f8e285ff58436789318cb9cd3b7ac3
Signed-off-by: Evelyn Huang <evhuang@google.com>
Reviewed-on: https://review.coreboot.org/19988
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
This patch perform resource mapping for PCI,
fixed MMIO, DRAM and IMR's based on inputs given by SoC.
TEST=Ensure PCI root bridge 0:0:0 memory resource allocation
remains same between previous implementation and current
implementation.
Change-Id: I15a3b2fc46ec9063b54379d41996b9a1d612cfd2
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/19795
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This patch perform resource mapping for PCI,
fixed MMIO, DRAM and IMR's based on inputs given by SoC.
TEST=Ensure PCI root bridge 0:0:0 memory resource allocation
remains same between previous implementation and current
implementation.
Change-Id: I93567a79b2d12dd5d6363957e55ce2cb86ff83a7
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/19796
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Add Intel common systemagent support for romstage and ramstage.
Include soc specific macros need to compile systemagent common code.
Change-Id: I969ff187e3d4199864cb2e9c9a13f4d04158e27c
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/19668
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
cherry-pick from Chromium, commit 8fbe1e7
On Braswell and Baytrail devices, by userland 'perf top',
observed demanding clocks on __vdso_clock_gettime() since
chromeos_3.18 kernel; besides, evaluated massive calling of
clock_gettime() cost, up to 700 ns in average.
It turns out that Linux kernel of map_vdso() first call of
remap_pfn_range() does not fall into reserve_pfn_range()
due to size parameter, instead it relies on lookup_memtype()
and potentially be failed to be identified as eligible RAM
resource because the function of pat_pagerange_is_ram() actually
walks through root's sibling.
Meanwhile, on current BSW (and BYT) firmware implementation
makes System RAM resources located on child leaf, combining all
of these factors makes the kernel treat the vvar page of vdso
as a uncached-minus one leading slow access in result.
This patch recollects TOLM accessing; as Aaron recalled some
core_msr_script turns off access to TOLM register, he suggests
to store tolm to avoid getting back a zero while setting acpi
nvs space.
Original-Change-Id: Iad4ffa542b22073cb087100a95169e2d2a52efcd
Original-Signed-off-by: Harry Pan <harry.pan@intel.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/368585
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Change-Id: Idc9765ec5c0920dc98baeb9267a89bec5cadd5a0
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/20060
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Update devicetree PCI config based on board spec:
- enable PCIe Root Ports 5 and 9 (wifi and nvme respectively)
- enable PCIe CLKREQ on RP9, disable on RP5
- enable USB OTG
- enable P2SB
Note: PCIe RP5 is on 0.1c.0 despite this being labeled as RP1
Change-Id: Ia71ed25bd41668df1ee3e4b4e28f54482722452c
Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm>
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/19939
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Needed for UEFI booting via Tianocore;
with PM timer disabled, payload hangs.
Change-Id: I6c65cb9d3e6a10baea4cc1e2d9e94c36fe419561
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/19938
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Change-Id: Ib63e5e8a1bcbc25c288dec7d1ef6c06239ada34b
Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm>
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/19937
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
The FSP Temp RAM init will fail if the mircocode values are set
to 0. A valid microcode update needs to be included and its size
and offset need to be set in the config.
Change-Id: I26d05bd7b37c8d91bf34f399c7c4189f9d3dd34a
Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm>
Reviewed-on: https://review.coreboot.org/19936
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Adding code to setup the spd information from sodimm.
Adapted from intel/kblrvp.
Change-Id: I0403f999dac1bdef0e9e1abe7c9c62407e223bb1
Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm>
Reviewed-on: https://review.coreboot.org/19935
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
The GPIO configuration matches the one from the original BIOS.
Some configs don't make much sense, but I kept it as is so it
would match (such as a NC pin with TX set to 1, or RXINV enabled).
Remove unnecessary early GPIO config.
Change-Id: Iaec8630cef9a523fb2e2503143aa4aa72fbedc1f
Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm>
Reviewed-on: https://review.coreboot.org/19934
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Like other devices using ENE embedded controllers, the librem13v2
requires this config option for the PS2 keyboard and mouse
(trackpad) to function properly.
Change-Id: Ifba13b93a1fe2e76b2790d1c273fd9e2b5368ab0
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/19933
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Add the initial directory for the port of the Librem 13 v2.
The base implementation was copied from the google/chell directory
and the chell references were replaced. spd directory was removed
since the RAM is not soldered on the MB. The Kconfig, board_info.txt
and devicetree.cb files were modified to match the Librem 13 v2
hardware information. The romstage.c, mainboard.c, Makefile.in and
dsdt.asl were modified to remove chromeos specific code. The boardid.c,
chromeos.c, chromeos.fmd, cmos.layout, ec.c, ec.h and smihandler.c
files were removed from the tree, and the acpi directory was replaced
with the acpi directory from the purism/librem13 board.
These changes allow us to remove the references to chromeos specific
code and allow coreboot to compile when the librem13v2 board is selected.
Change-Id: I24263fde18fcea70163dbdc59df6ea1d98c97af8
Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm>
Reviewed-on: https://review.coreboot.org/19932
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
The FADT revision was set to 5, but we do not implement the
ACPI v5.0 specification, which prevents Windows from booting.
Setting it to v3 (matching most other boards) fixes the issue
and Windows now boots normally.
Bug found by Matt DeVillier, fix tested by Youness Alaoui on
Librem 13 v1 hardware.
Please also see commits 00d250e2289de (intel/skylake: Switch FADT
to ACPI version 3.0) [1] and 27e6042bb7d0b1 (intel/apollolake:
Switch FADT to ACPI version 3.0) [2].
[1] https://review.coreboot.org/19453
[2] https://review.coreboot.org/19146
Change-Id: Ide97cbf64f7b05018433436431ab4723b217fe22
Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm>
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/19985
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
