| Age | Commit message (Collapse) | Author |
|---|
|
Define the ChromeOS GPIOs (physical write-protect and virtual recovery
mode) in ACPI tables so the OS knows which physical pad is used for them.
BUG=b:181887865
TEST=flashrom_tester is able to "see" the WP GPIO
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I3feed366afd6507894a1d31304891cc785a4d314
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51347
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Intel ADL-P supports an additional memory-mapped 16MiB window into the
platform SPI flash. Support for this window already exists at the SoC
level, so all that is needed is to properly organize the flash map to
take advantage of this. FW_SECTION_A moves down to the bottom of the
available space in the lower 16MiB half, and FW_SECTION_B moves to the
bottom of the top 16MiB half. RW_LEGACY is squashed down to 2M.
BUG=b:182088676
TEST=build and boot to OS from FW_MAIN_A
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I60483b7e638c0a7e41f1f7e2b5503ae02e9906bd
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51345
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
|
|
Prevent writes to Global SMI enable as recommended by the BWG.
Change-Id: I7824464e53a2ca1e860c1aa40d8a7d26e948c418
Signed-off-by: Marc Jones <marcjones@sysproconsulting.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51226
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jay Talbott <JayTalbott@sysproconsulting.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Add SOC_INTEL_COMMON_PCH_LOCKDOWN and PMC_GLOBAL_RESET_ENABLE_LOCK
to meet device security requirements.
LOCKDOWN has dependencies on SOC_INTEL_COMMON_PCH_BASE and
several other common block devices. Add COMMON_PCH_BASE and
COMMON_PCH_SERVER to pick up LOCKDOWN and the dependencies.
COMMON_PCH_SERVER adds the following common devices that were not
previously included by XEON_SP:
SOC_INTEL_COMMON_BLOCK_CHIP_CONFIG
SOC_INTEL_COMMON_BLOCK_CSE
SOC_INTEL_COMMON_BLOCK_GPIO_ITSS_POL_CFG
SOC_INTEL_COMMON_BLOCK_ITSS
SOC_INTEL_COMMON_PCH_LOCKDOWN
SOC_INTEL_COMMON_BLOCK_SATA
SOC_INTEL_COMMON_BLOCK_SMBUS
SOC_INTEL_COMMON_BLOCK_XHCI
Change-Id: Iab97123e487f4f13f874f364a9c51723d234d4f0
Signed-off-by: Marc Jones <marcjones@sysproconsulting.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49849
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jay Talbott <JayTalbott@sysproconsulting.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Add a server Kconfig option to select a subset of common PCH devices.
Client devices are included if server isn't selected. This maintains
the current Kconfig behavior.
Change-Id: If11d1a51192dd87ad770b8aa53ce02b6a28b8da8
Signed-off-by: Marc Jones <marcjones@sysproconsulting.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51307
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jay Talbott <JayTalbott@sysproconsulting.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Enlarge CONSOLE_CBMEM_BUFFER_SIZE from 128K (default) to 512K, so that
more DRAM calibration logs can be stored in CBMEM console.
BUG=b:181933863
TEST=emerge-asurada coreboot
TEST="cbmem -c" shows the whole full calibration log
BRANCH=none
Change-Id: If82cbee5d2d5e97d98cbdaecda739d91a7cca0f8
Signed-off-by: Yu-Ping Wu <yupingso@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51275
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Fleex has other project share the same FW. Only fleex has LTE sku.
So we need to make sure it is fleex then check if LTE sku.
BUG=b:181946744
BRANCH=octopus
TEST=Check no SAR table can be loaded with sku id 4 and 5.
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I9f3d5fed4315fc716acad1a07735221d154c377e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51288
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marco Chen <marcochen@google.com>
Reviewed-by: Henry Sun <henrysun@google.com>
|
|
This file is common for all the AMD platforms.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I10ee600b4bcd7aaff39bfab075eb4dbc9096b435
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51299
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patchs adds a new CBFS primitive that allows callers to pass in an
allocator function that will be called once the size of the file to load
is known, to decide on its final location. This can be useful for
loading a CBFS file straight into CBMEM, for example. The new primitive
is combined with cbfs_map() and cbfs_load() into a single underlying
function that can handle all operations, to reduce the amount of code
that needs to be duplicated (especially later when file verification is
added). Also add a new variation that allows restraining or querying the
CBFS type of a file as it is being loaded, and reorganize the
documentation/definition of all these accessors and variations in the
header file a little.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I5fe0645387c0e9053ad5c15744437940fc904392
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49334
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This patch pulls control of the memory pool serving allocations from the
CBFS_CACHE memlayout area into cbfs.c and makes it a core part of the
CBFS API. Previously, platforms would independently instantiate this as
part of boot_device_ro() (mostly through cbfs_spi.c). The new cbfs_cache
pool is exported as a global so these platforms can still use it to
directly back rdev_mmap() on their boot device, but the cbfs_cache can
now also use it to directly make allocations itself. This is used to
allow transparent decompression support in cbfs_map().
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I0d52b6a8f582a81a19fd0fd663bb89eab55a49d9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49333
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
The new CBFS API contains a couple of trivial wrappers that all just
call the same base functions with slightly different predetermined
arguments, and I'm planning to add several more of them as well. This
patch changes these functions to become static inlines, and reorganizes
the cbfs.h header a bit for better readability while I'm at it.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: If0170401b2a70c158691b6eb56c7e312553afad1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49331
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Doing this all in one go keeps the files consistent and should make
future refactoring easier.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I4a701d24fc9ccd68dce8789aab15fd21964a55f9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49330
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=b:181809122
TEST=builds
Signed-off-by: Mathew King <mathewk@chromium.org>
Change-Id: I64475a475e9b72a6edd04ce0728591e0649d9f60
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51244
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Mainboards can configure gpios in their smihandler.
BUG=b:180507707
TEST=builds
Signed-off-by: Mathew King <mathewk@chromium.org>
Change-Id: I6c2b28f981f580cfb6f982a2d7e4c309d6f82e0b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51263
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
BUG=b:180507937
TEST=builds
Signed-off-by: Mathew King <mathewk@chromium.org>
Change-Id: Ic29fa569899e7b77819ce7f72c6a748621684c40
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51290
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This change will allow for GEVENTs to be used in ASL code.
BUG=b:180507937
TEST=builds
Signed-off-by: Mathew King <mathewk@chromium.org>
Change-Id: I77abd134555c21a32a302ee92cd080284cd2e634
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51289
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
GOP needs to register the new framebuffer.
BUG=b:171234996
BRANCH=Zork
Change-Id: I17b6533520b0628df9529d09f70d5fc28339d522
Signed-off-by: Nikolai Vyssotski <nikolai.vyssotski@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49864
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
If bit 0 of byte 0x47 is set FSP will perform full memory training
even if previously saved data is supplied.
Up to and including FSP 2021 WW01 it was reset internally at the end
of PostMemoryInit. Starting with WW03 this is no longer the case and
Intel advised that this bit should be reset externally if valid MRC
data is present.
Change-Id: I9c4191d2fa2e0203b3464dcf40d845ede5f14c6b
Signed-off-by: Deomid "rojer" Ryabkov <rojer9@fb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51230
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
BUG=b:180456030
TEST=`mosys` is able to detect the platform correctly
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: Ifbaa4a380bdb546bb54d579b46fe5760b2f4b754
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51313
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
BUG=b:181887865
TEST=`crossystem` shows correct state of WP signal when toggled
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: If49ca1d70cc36ab74d70e858336679c0a9a3258e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51312
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
|
|
The default value for the LidStatus is "LidClosed" mean 0
Because of this GOP skips graphics initialization assuming
lid is closed even though lid is open. This Patch is to set
LidStatus UPD to 1 whenever RUN_FSP_GOP config is selected.
BUG=b:178461282
BRANCH=None
TEST=Build and boot ADLRVP and verify eDP is coming up in
depthcharge
Change-Id: I1648ae0f06e414b2a686e325acf803deb702b7a5
Signed-off-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51131
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
|
|
Move PRERAM_CBMEM_CONSOLE to SRAM L2C and increase its size from 15K to
400K. With this change, most part of the DRAM full calibration log can
be stored in CBMEM console.
BUG=b:181933863
TEST=emerge-asurada coreboot
TEST=Hayato boots
BRANCH=none
Change-Id: I896884d298e197149f75865e9d00579124a34404
Signed-off-by: Yu-Ping Wu <yupingso@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51174
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
|
|
Many header files and helper macros have been moved to the
common folder and we want to use them in mt8173/mt8183
DRAM calibration code.
Signed-off-by: Xi Chen <xixi.chen@mediatek.com>
Change-Id: Ifa483dcfffe0e1383cb46811563c90f0ab484d5d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51224
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
To reduce qualification effort, we want to pre-populate DRAM by their
size, package type and geometry so when a new DRAM is introduced we
don't need to spin off a new firmware release.
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Signed-off-by: Xi Chen <xixi.chen@mediatek.com>
Change-Id: I42ee170c159e551e840ab4e748f18f5149506b4f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51202
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Mediatek has released the reference implementation for DRAM
initialization in vendorcode/mediatek/mt8192/dramc (CB:50294)
so we want to use it to replace the derived calibration code
in soc folder.
Signed-off-by: Xi Chen <xixi.chen@mediatek.com>
Change-Id: I2b2f41d774c6b85f106867144fb0b29a4a1bdfcf
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51125
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
|
|
To reduce duplicated dram sources on seperate SOCs,
add dpm, dram_init, dramc_params, memory(fast-k or full-k)
implementations, also add dramc log level macro header files.
Signed-off-by: Xi Chen <xixi.chen@mediatek.com>
Change-Id: I557c96b3d09828472b8b6f932b0192a90894043e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51203
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
|
|
This is the DRAM initialization code from the reference
implementation released by Mediatek for MT8192.
The DRAM calibration code can be taken as a standalone
library, used by different boot loaders for initializing
DRAM and following a different coding style (coreboot was
using Linux Kernel coding style), so we have to put it
in vendor code folder.
Signed-off-by: Xi Chen <xixi.chen@mediatek.com>
Change-Id: I3853204578069c6abf52689ea6f5d88841414bd4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50294
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Support 4G+128G MT29VZZZAD9GQFSM-046 W.9S9 discrete DDR bootup.
BUG=b:162292216
BRANCH=kukui
TEST=Boots correctly on Kukui.
Signed-off-by: Jessy Jiang <jiangchao5@huaqin.corp-partner.google.com>
Change-Id: I5657a007154bc52c6f0f27e1de6e3294a5e74ad7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48686
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
Change-Id: Ia338ce1a36aa0a14017201c1fc16f84915f55c07
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51156
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Rearrange the code to ease comparing against Broadwell.
Tested with BUILD_TIMELESS=1, Asrock B85M Pro4 remains identical.
Change-Id: I3143f07ed845e0c6b1444817029a437db3b959e3
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42631
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Performing ME finalization in SMM does not seem to be required.
Tested on Asrock B85M Pro4, ME still gets finalized successfully.
Change-Id: I9fde40a54f3fb8da2fba46c531443fdd2e067077
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51036
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Tested with BUILD_TIMELESS=1, Asrock B85M Pro4 remains identical.
Change-Id: I87fa1ffb353135cc361ac6be30a4fc69e7f8ed47
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51037
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Also introduce uintptr_t cast and use PCI_BASE_ADDRESS_MEM_ATTR_MASK.
Change-Id: I32fdcc6b1ffde1b0701218a3bd0a61ab827081b5
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51035
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Use the common PCIEXP_HOTPLUG code to generate a dummy device for PCIe
ports supporting hotplug. This allows to have control over how much
resources are allocated to hotplug ports.
Tested on thinkpad X220: now hotplugging a dGPU via the expresscard
slot sometimes works.
Change-Id: I3eec5214c9d200ef97d1ccfdc00e8ea0ee7cfbc6
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51068
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Patrick Rudolph
|
|
This change moves GPE configuration from brya0/overridetree.cb to
baseboard/devicetree.cb since all variants will end up using the same
configuration.
TEST=Verified using "abuild -p none -t google/brya -b brya0
--timeless" that coreboot.rom generated with and without this change
is the same.
Change-Id: Ie31bf2bf8a91da82fca77c78fb0a735a2645de55
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51298
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
This change updates MAINBOARD_PART_NUMBER string to use uppercase for
first character. This matches what all others boards do.
BUG=b:180456030
Change-Id: I10eaeef5ec662a5718b787a3f0e3705cf70d751d
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51297
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Also rename mrc_cache to apob_cache.
BUG=b:181766974
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I4877b05443452c7409006c1656e9d574e93150a0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51267
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
BUG=b:181843816
Change-Id: I25309a8f0900070a8307fbce90ccb6d47f9c3dfc
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51261
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=b:181843816
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I74246cd0d2f866022604ec3e8a8d523c273cdef4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51259
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
BUG=b:181160586, b:181843816
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: Ic201ad047fd0d593749d2b993f843f7e188a5c98
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51258
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Implement the mainboard_tcss_get_port_info weak function so that the TCSS
muxes can be properly configured to ensure mapping is correct in mux. This
ensures that any devices that are connected during boot are not improperly
configured by the Kernel.
BUG=b:180426950
BRANCH=firmare-volteer-13672.B
TEST= Verified that the SOC code that initialized TCSS muxes to disconnect
mode is executing properly for all TCSS ports and verified that USB3 devices
are no longer downgrading to USB2 speed if connected during boot.
Change-Id: I59e5c5a7d2ab5ef5293abe6c59c3a585b25f7b75
Signed-off-by: Brandon Breitenstein <brandon.breitenstein@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51195
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
TCSS muxes being left uninitialized during boot is causing some USB3
devices to downgrade to USB2 speed. To properly configure the Type C ports
the muxes should be set to disconnected state during boot so that the port
mapping of USB2/3 devices is properly setup prior to Kernel initializing
devices.
BUG=b:180426950
BRANCH=firmware-volteer-13672.B
TEST= Connected USB3 storage device and rebooted the system multiple
times to verify that devices were no longer downgrading to USB2 speed.
Change-Id: I4352072a4a7d6ccb1364b38377831f3c22ae8fb4
Signed-off-by: Brandon Breitenstein <brandon.breitenstein@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51194
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Use lowercase `port` in both the spec and the body.
Change-Id: I3d1e2abe03eedcaf57716af444a3e3b8a61b60d4
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51146
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Change-Id: I46bc854239e723a1685279f634e635b72e7b3af9
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51135
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Change the function parameters to avoid preprocessor usage.
Change-Id: Iec43e057ed2a629e702e0f484ff7f19fe8a0311b
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51236
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Done to ease diffing against Lynxpoint.
Change-Id: Ib4280b26799eab6d4a2bb41a14a76695caa31e86
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47021
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Continue unifying Lynx Point and Wildcat Point (PCH for Broadwell) code.
Define the WPT-LP SMBus PCI device ID, add it to smbus.c of Lynx Point,
and drop all now-unnecessary SMBus code from Broadwell.
Change-Id: I864d7c2dd47895a3c559e2f1219425cda9fd0c17
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51235
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Add marshaling and unmarshaling support for cr50 vendor sub-command to
reset EC and a interface function to exchange the same.
BUG=b:181051734
TEST=Build and boot to OS in drawlat. Ensure that when the command is
issued, EC reset is triggered.
Change-Id: I46063678511d27fea5eabbd12fc3af0b1df68143
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51164
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Add supported memory parts in the mem_parts_used.txt and generate the
SPD ID for the memory parts. The memory parts being added are:
MT53E512M32D2NP-046 WT:E
K4U6E3S4AA-MGCR
H9HCNNNBKMMLXR-NEE
BUG=None
TEST=Build the blipper board.
Change-Id: Ia7e4c1d5c06013c1902816d6dcafb5a8a0386bb3
Signed-off-by: Zanxi Chen <chenzanxi@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51201
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
The datasheet indicates that this bit is reserved. However, subsequent
patches need to use this macro in common code, or else builds fail. To
iron out this difference, mask out the bit in `soc_get_smi_status`, so
that common code always sees it as zero. Finally, add an entry for the
bit in `smi_sts_bits` for debugging usage, noting that it is reserved.
Change-Id: Ib4408e016ba29cf8f7b125c95bfa668136b9eb93
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50916
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Convert the lines starts with whitespace with tab as applicable.
Change-Id: Ife7b27360661cbfd2c90e2b643ed31225ded228c
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51250
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Update telemetry settings for vilboz.
VDD Slope : 26939 -> 27225
VDD Offset: 125 -> 187
SOC Slope : 20001 -> 26559
SOC Offset: 168 -> 89
BUG=b:177162553
BRANCH=zork
TEST=emerge-zork coreboot
Signed-off-by: John Su <john_su@compal.corp-partner.google.com>
Change-Id: Iaf7c5083c4c5affec5ae0b5583efb5237e10d0ec
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51165
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Reviewed-by: chris wang <Chris.Wang@amd.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
|
|
1. No gpio control in bootblock
2. Power on and then deassert reset at the end of ramstage gpio
3. Disable power and assert reset when entering S5
On "reboot", the amount of time the power is disabled for is
equivalent to the amount of time between triggering #3 and wrapping
around to #2.
This change affects the following volteer variants that include an FPMCU:
1. Drobit
2. Eldrid
3. Elemi
4. Halvor
5. Malefor
6. Terrador
7. Trondo
8. Voema
9. Volteer2
10. Voxel
BUG=b:178094376
TEST=none
Change-Id: Ib51815349cea299907c10d6c56c27bd239e499e7
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50828
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
The original implementation of early tcss resulted in calling to mainboard
then back to soc then back to mainboard to properly configure the muxes.
This patch addresses that issue and instead just gets all the mux
information from mainboard and does all config in the soc code.
BUG=none
BRANCH=firmware-volteer-13672.B
TEST=Verified functionality is not effected and early TCSS still functions
Change-Id: Idd50b0ffe1d56dffc3698e07c6e4bc4540d45e73
Signed-off-by: Brandon Breitenstein <brandon.breitenstein@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47684
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
`pmc_send_ipc_cmd()` expects the caller to pass in a pointer to a valid
request and response buffer. However, early_tcss driver was passing in
a NULL pointer for response buffer which would result in invalid
access by `pmc_send_ipc_cmd()`.
Currently, the response buffer is not used in `update_tcss_mux()`. So,
this change drops the passing of `rbuf` parameter to `send_pmc*`
helpers and instead uses a local `rsp` variable in the respective
functions. All the PMC functions used in early_tcss driver return some
kind of response. These should be checked to return appropriate
response code back to the caller. However, this needs to be done as a
separate change.
Change-Id: I215af85feed60b6beee17f28e3d65daa9ad4ae69
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51232
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
With the aliases some of the comments are redundant. I'm still not sure
if the Ethernet controller on the embedded SKUs supports 10G or only 1G.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I1e432c12f92a622f8ee05be19acb2c304dd74afb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51242
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Mathew King <mathewk@chromium.org>
|
|
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I12ec6a3c2704effc1a626181898a9ed7a17f0640
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51239
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Since the support for the GSMI ELOG isn't implemented in the SMI handler
yet, the corresponding code isn't added to fch_slp_typ_handler in this
patch.
BUG=b:181766974
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ia27b2486dde1a373607ce895a975e873d9026ba1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51234
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
BUG=b:181766974
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I5b9b4c3d57945ea7c3287cf47f3d9704f42ff24b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51233
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
In commit 2609eaaa8f (src/drivers/i2c/rx6110sa: Omit _HID temporarily)
the randomly assigned and therefore wrong ACPI ID for RTC RX6110SA was
removed. In the meantime Seiko-Epson did a great job and registered an
official vendor ID in the ACPI database [1]. Further on, Seiko-Epson
has now assigned the unique Product Identifier for the RX6110SA, which
is '6110'. The assignment of the Product Identifier is controlled by
the vendor and there is no official database where this ID is stored
in. It is up to the vendor to make sure that this ID stays unique.
This patch adds this new vendor and product ID to the driver. Together
with a pending Linux patch this RTC is now useable as ACPI device in
Linux.
[1] https://uefi.org/ACPI_ID_List?search=SECC
Change-Id: I45838162f014a760520692c6dcaae329ad98547d
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51176
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Johannes Hahn <johannes-hahn@siemens.com>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Replace if HAVE_ACPI_TABLES statement with depends HAVE_ACPI_TABLES.
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: Ie6ebfde49f0f3c205e174c5113feb75444dedba8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51166
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Add ALC1015 AMP support.
ALC1015Q-VB Datasheet Rev 0.1
BUG=b:177971830
TEST: ALC1015P driver can probe properly.
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: Id93845024aa2cded69acc88d594c222f2f821f79
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51051
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Modify USB port to match schematics.
And assigned USB2 port to type-c use.
BUG=b:177481079
BRANCH=firmware-volteer-13672.B
TEST=emerge-volteer coreboot
Change-Id: I25412d16df8ad809c05635022c11bd8882d002c5
Signed-off-by: hao_chou <hao_chou@pegatron.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49980
Reviewed-by: Wayne3 Wang <wayne3_wang@pegatron.corp-partner.google.com>
Reviewed-by: Zhuohao Lee <zhuohao@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
When printing error information during DRAM training, be more verbose
by printing the channel number.
Change-Id: If4109bd0573e3d9f90d699d89350ddbcc48714d3
Signed-off-by: Moritz Fischer <moritzf@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51127
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
There is no need for explicit 0 comparison, any return value not equal
to 0 is treated as error.
Change-Id: I72612af4108a616b6247ee68c8ac2a53242b0853
Signed-off-by: Moritz Fischer <moritzf@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51126
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
We will need more FSPS UPD space for PEI GOP changes coming.
BUG=b:171234996
BRANCH=Zork
Cq-Depend: chrome-internal:3609213, chromium:50576
Change-Id: I35d0bb0ee30e04f66882b6103acd9d673d040c07
Signed-off-by: Nikolai Vyssotski <nikolai.vyssotski@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50552
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Renoir/Cezanne have two SATA controllers with 2 ports each, so call them
sata_0 and sata_1.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I6ebfd3a85f9b513901f205bc299e92564fa329e5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51190
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Loading wifi_sar-vilboz-1.hex for vilboz360 LTE sku for the present.
BUG=b:177684735, b:176168400
BRANCH=zork
TEST=emerge-zork coreboot chromeos-bootimage, then verify that tables are
in CBFS and loaded by iwlwifi driver.
Signed-off-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
Change-Id: I477b55d64fd9d33d753b10b2de443041a12d13e2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51171
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Kangheui Won <khwon@chromium.org>
|
|
Change-Id: I3e82a51173f561df560c36528a9b7ec26cf489b5
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49966
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
1) Micron MT53E1G32D2NP-046
2) Micron MT53E2G32D4NQ-046
BUG=b:181378727
TEST=none
Change-Id: I413e35cdb7c34388c3e159f8f9584fae2d21a355
Signed-off-by: Amanda Huang <amanda_hwang@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51170
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Add memory part MT53E2G32D4NQ-046 to LP4x global list. Attributes
are derived from data sheets.Also, regenerate the SPD files for ADL
SoC using the newly added parts.
BUG=b:181378727
TEST=Compared generated SPD with data sheets and checked in SPD
Change-Id: Ic06e9d672a2d3db2b4ea12d15b462843c90db8f6
Signed-off-by: Amanda Huang <amanda_hwang@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51167
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Current implementation exposes GPP_F4 cnvi reset pin as reset
gpio instead of GPP_D4(BT_DISABLE_L). GPP_F4 is native and driven
by SoC. It should not be driven by driver.
BUG=b:180875586
Change-Id: I589fc2b55ee2947cc638fe17540bbd24f5bfb8f4
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51178
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: Iafa7d40fc21e62f99dbdc2001ab6525a2a77ff50
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44865
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Guard against unintended operator precedence and associativity issues.
Change-Id: I342682a57fde9942cdf7be10756ee21c10af802a
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50917
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
To allow unifying bootblock.c in follow-ups, move a function call.
Change-Id: I0f40ee7fd47f7f9f582f314dfcd1b4b93b1db791
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51148
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
There are seven identical copies of the same file. One is enough.
Change-Id: I68c023029ec45ecfaab0e756fce774674bb02871
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50937
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
State of ME firmware SKU is independent of power-down mitigation.
Change-Id: I014c1697213efaefcb0c2a193128a876ef905903
Signed-off-by: Benjamin Doron <benjamin.doron00@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51204
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Use LZ4 algorithm to compress FSP-S. This saves ~40 KiB and reduces the
boot time by ~7 ms. LZMA would save a further ~1 KiB, but adds ~9 ms to
the boot time.
LZMA size:
fsps_lzma.bin 0xb0dc0 fsp 146578 LZMA (188416 decompressed)
LZMA decompression time:
15:starting LZMA decompress (ignore for x86) 388,716 (47,646)
16:finished LZMA decompress (ignore for x86) 406,167 (17,450)
LZ4 size:
fsps_lz4.bin 0x242dc0 fsp 147442 LZ4 (188416 decompressed)
LZ4 decompression time:
17:starting LZ4 decompress (ignore for x86) 384,736 (47,864)
18:finished LZ4 decompress (ignore for x86) 384,796 (59)
Change-Id: Idace01227cfd2312b2c4c4ea1e6aaac8c21cd6b0
Signed-off-by: Benjamin Doron <benjamin.doron00@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50726
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Add wake events to the elog for: HDA, GbE, SATA, CSE, south XHCI,
south XDCI, CNVi WiFI, TCSS XHCI, TCSS XDCI, and TCSS DMA ports.
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: Icd50dc7ee052cf13b703188c0fd3d8b99216cb4a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47399
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
|
|
Change-Id: I5cf54ae0456147c88b64bd331d4de5ca2e941f8a
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47413
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Log PCIe root port wake events in the elog.
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I2867b1fa12f639cd6c49a58f698b51b089e2b483
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47398
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
|
|
This lock bit can be set later, and should also be set for LynxPoint-H.
This eases merging with Broadwell, which already sets this lock bit
after `spi_finalize_ops()` in a dedicated finalisation function.
Tested on Asrock B85M Pro4 (LynxPoint-H), the lock bit is now set.
Change-Id: I5c32127f2b4cfdfeb0e30a64e5bdda89958933cb
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47036
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
ASL+ Optimizing Compiler/Disassembler version 20200925 remarks:
IASL build/dsdt.aml
Intel ACPI Component Architecture
ASL+ Optimizing Compiler/Disassembler version 20200925
Copyright (c) 2000 - 2020 Intel Corporation
dsdt.asl 222: Name(PSa, Package(){
Remark 2182 - ^ At least one lower case letter found in NameSeg, ASL is case insensitive - converting to upper case (PSA_)
dsdt.asl 228: Name(APSa, Package(){
Remark 2182 - ^ At least one lower case letter found in NameSeg, ASL is case insensitive - converting to upper case (APSA)
Execute the command below to fix all occurences:
git grep -l PSa | xargs sed -i 's/PSa/PSA/g'
Change-Id: Ia458c98a4774fb5745825aecf996a476e66eaa3f
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51152
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
TEL_CFG_BAR variables have the same value as PCI_BASE_ADDRESS.
This fix re-uses an already existing variable in crashLog.
BUG=None
TEST=CrashLog data generated, extracted, processed, decoded sucessfully on delbin.
Signed-off-by: Francois Toguo <francois.toguo.fotso@intel.com>
Change-Id: If063d1ea4189dbc5a75f37d86ce158e8f1bd808d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51096
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
The `FORCE_ENABLE` and `FORCE_DISABLE` names do not match what FSP UPDs
say, and can be confused with the `PchHdaTestPowerClockGating` UPD.
Replace the enum with a bool, and drop the confusing names. Note that
the enum for Ice Lake was incorrect, but no mainboards used the option.
Change-Id: I2c9b4c6a2f210ffca946ca196299fa672a06ccc7
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51154
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Make the SATA LED blink when coreboot dies. GPIO functions aren't
compiled in for postcar, so add a check to prevent linker failures.
TEST: Try to boot Librem Mini WHL without RAM, observe blinking (and
also blinding LED). Re-install RAM (and re-seat RAM a few times),
boot to OS, and observe SATA LED operating normally, as expected.
Change-Id: I0ffac0ab02e52e9fbba7990f401d87e50a1b5154
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50013
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Benjamin Doron <benjamin.doron00@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
PCIEXP_HOTPLUG has a prompt and as such is not supposed to be forced.
Just change the default value to 'y'.
Change-Id: Ie4248700f5ab5168bff551b740d347713273763c
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51151
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Backport commit 0cded1f116 (soc/intel/tigerlake: Add SMRR Locking
support) to other client platforms. The SMRR MSRs are core-scoped on
Skylake and Ice Lake, at least. Older platforms do not support SMRR
locking, but now there's seven copies of the same file in the tree. A
follow-up will deduplicate smmrelocate.c files into common CPU code.
I cannot test Jasper Lake nor Elkhart Lake, but they should still work.
As per documentation I do not have access to, Elkhart Lake seems to
support SMRR locking. However, Jasper Lake documentation is unclear.
Tested on Purism Librem Mini v1 (WHL-U i7-8565U), still boots and SMRR
MSRs have the same value on all cores/threads (i7-8565U supports HT).
Change-Id: Icbee0985b04418e83cbf41b81f00934f5a663e30
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50936
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Pineview does not support PEG.
Change-Id: Ib0006dbd54e6f2031b97ed11ce61407ffcfa6244
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51150
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
This is a cosmetic change.
Make the formatting consistent with the rest of the tree.
Change-Id: Ic90e5584938592f1c2ab41edfcc773702822070d
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51149
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Booted fine on the first try. Most things work properly, but I haven't
tested them thoroughly. Native raminit chokes with a DIMM in the second
slot, but the first slot works properly.
Change-Id: I2126c7d31e0d8a8f80df69fdcdcd202b87f219a4
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40465
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Returning an error on a failure to measure makes the system not
bootable.
Change-Id: Ifd20e543d3b30de045c0656eccdcc494c2fb10ce
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51099
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Christian Walter <christian.walter@9elements.com>
|
|
There is going to be an upcoming board version for Drawlat/man and
Drawcia. Hence apply the override GPIO table without pad termination for
board versions 6 or 8 alone.
BUG=None
BRANCH=dedede
TEST=Build and boot to OS in Drawcia.
Change-Id: I320de9a0c37ac033f3efda74eeb8f36e34667fd4
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51153
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Evan Green <evgreen@chromium.org>
|
|
These files were automatically generated by the lpddr4 version of
gen_part_id.go.
BUG=b:178715165
TEST=Build
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: I3797ba6d52248961418000614a4f7885182521a3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51021
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
These SPDs were generated by the lpddr4 version of gen_spd.go from the
global_lp4x_mem_parts.json.txt file.
BUG=b:178715165
TEST=None
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: I7b9bd04534d6e45dbfe10a0028052978ef3d7c17
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51020
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Looks like I forgot about trogdor-rev1 in CB:51004. Unlike rev0 (other
special case) or rev2 (works like CoachZ/Homestar), rev1 used the same
pin as Lazor and Pompom for EN_PP3300_DX_EDP. Apparently there are still
some people using these, so add in another special case for that.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I7093aa63778d69fde240af3b0c62b97ac99c28dc
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51196
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The legacy DMA is not used by linux. This change frees up those IO
ports.
When FSP-S runs, it re-enables the legacy DMA IO region, so we need to
disable it again.
BOOTBLOCK: PMx00: 0xe3060bf3
ROMSTAGE - Before FSP: PMx00: 0xe3060bf3
ROMSTAGE - After FSP: PMx00: 0xe3060bf7
BUG=b:180949454
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I7792d1f8ea40eb1c7f6cca67e9907208884ac694
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51076
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Most devices are now disabled by default in the chipset. Enable the
iGPU and two XHCI controllers that are required to boot the board.
BUG=b:180528708
TEST=To be tested
Signed-off-by: Mathew King <mathewk@chromium.org>
Change-Id: I54a4547217fb8e9f67fc0c8e1e36e96dfaae331c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51095
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=b:180523962
TEST=builds
Signed-off-by: Mathew King <mathewk@chromium.org>
Change-Id: Ic8f30f6d7c4781d4e8451546b39395a74393608f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50882
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
BUG=b:180507937
TEST=builds
Signed-off-by: Mathew King <mathewk@chromium.org>
Change-Id: Ic607d6bca5c70255332a6fbee2b63e6daba7d1e7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51047
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
