| Age | Commit message (Collapse) | Author |
|---|
|
Dump the DBG2 table on Linux console.
$> acpidump -s
ACPI: DBG2 0x0000000000000000 000054 (v00 COREv4 COREBOOT 00000000 **)
$> acpidump > acpidump.bin
$> acpixtract -a acpidump.bin
$> iasl -d dbg2.dat
$> cat dbg2.dsl
/*
* ACPI Data Table [DBG2]
*
* Format: [HexOffset DecimalOffset ByteLength] FieldName : FieldValue
*/
[000h 0000 4] Signature : "DBG2" [Debug Port table type 2]
[004h 0004 4] Table Length : 00000054
[008h 0008 1] Revision : 00
[009h 0009 1] Checksum : FA
[00Ah 0010 6] Oem ID : "COREv4"
[010h 0016 8] Oem Table ID : "COREBOOT"
[018h 0024 4] Oem Revision : 00000000
[01Ch 0028 4] Asl Compiler ID : "CORE"
[020h 0032 4] Asl Compiler Revision : 20220331
[024h 0036 4] Info Offset : 0000002C
[028h 0040 4] Info Count : 00000001
[02Ch 0044 1] Revision : 00
[02Dh 0045 2] Length : 0028
[02Fh 0047 1] Register Count : 01
[030h 0048 2] Namepath Length : 0002
[032h 0050 2] Namepath Offset : 0026
[034h 0052 2] OEM Data Length : 0000 [Optional field not present]
[036h 0054 2] OEM Data Offset : 0000 [Optional field not present]
[038h 0056 2] Port Type : 8000
[03Ah 0058 2] Port Subtype : 0012
[03Ch 0060 2] Reserved : 0000
[03Eh 0062 2] Base Address Offset : 0016
[040h 0064 2] Address Size Offset : 0022
[042h 006612] Base Address Register : [Generic Address Structure]
[042h 0066 1] Space ID : 00 [SystemMemory]
[043h 0067 1] Bit Width : 00
[044h 0068 1] Bit Offset : 00
[045h 0069 1] Encoded Access Width : 03 [DWord Access:32]
[046h 0070 8] Address : 00000000FEDC9000
[04Eh 0078 4] Address Size : 00000100
[052h 0082 2] Namepath : "."
Raw Table Data: Length 84 (0x54)
00: 44 42 47 32 54 00 00 00 00 FA 43 4F 52 45 76 34 // DBG2T.....COREv4
10: 43 4F 52 45 42 4F 4F 54 00 00 00 00 43 4F 52 45 // COREBOOT....CORE
20: 31 03 22 20 2C 00 00 00 01 00 00 00 00 28 00 01 // 1." ,........(..
30: 02 00 26 00 00 00 00 00 00 80 12 00 00 00 16 00 // ..&.............
40: 22 00 00 00 00 03 00 90 DC FE 00 00 00 00 00 01 // "...............
50: 00 00 2E 00 // ....
BUG=b:303689867
Change-Id: I3c97a78d1889549421baf0bc1a2e8f959a0f47e2
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79174
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The Microsoft Debug Port Table 2 (DBG2) specification says that the
serial port subtype 0x00 should only be used for I/O-mapped 16550
compatible UARTs. The subtype 0x12 is a superset of that, and supports
specifying MMIO vs IO and the register access size via the generic
address structure. Rename the subtype 0x00 definition to
ACPI_DBG2_PORT_SERIAL_16550_IO_ONLY and add the subtype 0x12 definition
as new ACPI_DBG2_PORT_SERIAL_16550, so that the acpi_write_dbg2_uart
function will write the correct subtype for the generic 16550 UART.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I816bb22e6f76e661c8b8e39a2a4cb83b0085acb5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79219
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Used by the OptiPlex 3020/7020/9020:
- EMI and Runtime registers work
- UART1 works (including IRQs)
- PS/2 keyboard and mouse untested
Signed-off-by: Mate Kukri <kukri.mate@gmail.com>
Change-Id: I9323198f1139cd0c3dd37f977ae7693b721654f4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/64359
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
|
|
Trim all GPIO comments like "origin ==> current".
BUG=b:304920262
TEST=pass building
Change-Id: I05daa4df16b6da3d3f971b75c7c467032e3f854d
Signed-off-by: Weimin Wu <wuweimin@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79321
Reviewed-by: Eric Lai <ericllai@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Fix GPP_D6 configuration for LTE power enable.
BUG=b:304920262
TEST=mmcli -m any
Change-Id: I2996fd35c2897269997bc0290e0ce93bbbaa1bf8
Signed-off-by: Weimin Wu <wuweimin@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79166
Reviewed-by: Eric Lai <ericllai@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Dolan Liu <liuyong5@huaqin.corp-partner.google.com>
|
|
Due to TCPC0 & TCPC1 exchanged compare to Neried design,
but related USB2 Ports not exchanged.
BUG=b:304920262
TEST=Tpye-C & DP functions workable
Change-Id: I9dacf06b1e672575a684856acdb10b6c88360b18
Signed-off-by: Weimin Wu <wuweimin@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79165
Reviewed-by: Dolan Liu <liuyong5@huaqin.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
For proto PCB:
GPP_C0 for enable power supply which also for sensor subsystem.
GPP_C0 must allways turn power on, so GPP_C6 is not only used
for enable function but also for stop report.
BUG=b:304920262
TEST=1. touchscreen function workable
2. INT pin no active during suspend
Change-Id: I7dabf205dba616f57ef9717f950eba96282d8e3d
Signed-off-by: Weimin Wu <wuweimin@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79164
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Dolan Liu <liuyong5@huaqin.corp-partner.google.com>
|
|
Update overridetree to correct AUX pin to USB-C port 3
BUG=b:299570339
TEST=emerge-brya coreboot chromeos-bootimage
Change-Id: I3a5a89c6008fbf28c927f83060e6e508d60845ba
Signed-off-by: Morris Hsu <morris-hsu@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79343
Reviewed-by: David Wu <david_wu@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
This patch adds compilation flags to BL31 to support loading
OP-TEE via an SMC from rootfs. This patch also reserves 80MB memory
space for running the OP-TEE image.
BUG=b:246837563
TEST=emerge-geralt coreboot
Change-Id: Ic38c8beb59c090ae56c5be6821dd8625435609e9
Signed-off-by: Kiwi Liu <kiwi.liu@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78801
Reviewed-by: Kiwi Liu <kiwi.liu@mediatek.corp-partner.google.com>
Reviewed-by: Yidi Lin <yidilin@google.com>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Brox has SSD and UFS storage per different SKU.
1. Set SSD on CPU PCIe port (PCIEX4_A) and configure related gpio
settings according to the schematic.
2. Enable UFS, also enable ISH since it is PCI function 0, required
for UFS function 7 to be enabled.
3. Set unused SRCCLKREQ signals to NC.
4. Remove unused gpio settings in variant gpio table to prevent
unexpected overrides.
BUG=b:311450057
BRANCH=None
TEST=emerge-brox coreboot
Change-Id: I88922bcfa13652006aa10078c3c444624fd4575e
Signed-off-by: Ivy Jian <ivy.jian@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79295
Reviewed-by: Shelley Chen <shchen@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This is likely a copy-paste leftover, since this SoC neither has a PCI
device with the device ID 0x1200 nor is family 10h.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I7095f208a7503545ea012241d058692a510109f3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79094
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Based on Platform Mapping Document for Deku (go/cros-deku-mapping)
from Nov 8, 2023 (Rev 0.4)
BUG=b:305793886
TEST=WIP, not tested yet
Change-Id: Ib37a7ebf0aca788d14fafea0f97e364beafb4c4d
Signed-off-by: Eran Mitrani <mitrani@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78960
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
The only thing romstage needs to do is find cbmem_top.
TESTED: reaches ramstage.
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Change-Id: Ic2837c4a2b0ec8dcd9dd99602f9c073999c36139
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76514
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Varshit Pandya <pandyavarshit@gmail.com>
|
|
Use an xPRF call to get the top of lower DRAM.
Organize Makefile to keep romstage/ramstage components separate.
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Signed-off-by: Martin Roth <gaumless@gmail.com>
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I269663414f4d8e39eb218cd6348bfce7989a79f9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76513
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Varshit Pandya <pandyavarshit@gmail.com>
|
|
Use fw_config to differentiate audio amps instead of the
kconfig option.
BRANCH=corsola
BUG=b:305828247
TEST=Verify devbeep in depthcharge console
Change-Id: I5f887f5e0d16dc14039fb12b636257d01339b2de
Signed-off-by: Yidi Lin <yidilin@chromium.org>
Signed-off-by: Yang Wu <wuyang5@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79309
Reviewed-by: Ruihai Zhou <zhouruihai@huaqin.corp-partner.google.com>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Quandiso does not use DB_1C, replace the fw_config with LTE only
daughterboard.
BUG=b:312094048
BRANCH=firmware-nissa-15217.B
TEST=emerge-nissa coreboot
Change-Id: Id7129e52d3733f62405f9d766f08563f05016c69
Signed-off-by: Robert Chen <robert.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79297
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Shawn Ku <shawnku@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Since lars has two touchscreen options, we need to determine which (if
any) are present on a given device at runtime so that there are not
multiple ACPI touchscreen devices (as it makes Windows unhappy).
Implement power sequencing and runtime detection for both touchscreen
options.
TEST=build/boot Win11/Linux on google/lars, verify touchscreen detected
and functional under both OSes.
Change-Id: I49ccb29ec4589315a4abe3c0ea8fa76f97080bcd
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79311
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
LARS has a Melfas touchscreen option, so add an entry for it. Adapted
from Chromium branch firmware-glados-7820.315.B, commit a26fe552569f
("Chell: Update DPTF parameters for CPU").
TEST=build/boot Linux on google/lars with Melfas touchscreen, verify
functional.
Change-Id: Idecd572335d7d5d52e4f89e85ebf7f0c90f23751
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79310
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The address space of possible SPD-EEPROMs 0x50..0x53 on the SMBus
interface is per default write-protected in FSP. This avoids that an
SPD-EEPROM on a DRAM module gets overwritten by the host.
On mc_ehl1, memory-down configuration is used and there is no SPD EEPROM
available. Nevertheless, there is a general purpose EEPROM on the same
address available which needs to stay writeable.
This patch disables the default-enabled write protect feature for the
SPD-EEPROM addresses just for mc_ehl1.
Test=Boot into Linux and make sure a write access into the EEPROM is
possible.
Change-Id: I6b0fcdbeb0dbf971cfdceb70d6f4845765a3bdb6
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79334
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jan Samek <jan.samek@siemens.com>
|
|
Enable MIPI camera for anraggar project.
Sensor: OV13B10-GA5A
Driver: DW9714V
EEPROM: GT24P64E
Ref to SCH, use MIPI 4-lane serial output interface.
BUG=b:309518095
TEST=Google Camera app working
Checking log with:
coreboot log:
\_SB.PCI0.I2C2.CAM0: Intel MIPI Camera Device I2C address 036h
\_SB.PCI0.I2C2.VCM0: Intel MIPI Camera Device I2C address 0ch
\_SB.PCI0.I2C2.NVM0: Intel MIPI Camera Device I2C address 050h
kernel log:
kernel: [ 6.140429] intel-ipu6-isys intel-ipu6-isys0: bind ov13b10 11-0036 nlanes is 4 port is 1
cros_camera_service[4755]: Read camera eeprom from /sys/bus/i2c/devices/i2c-PRP0001:02/eeprom
cros_camera_service[4755]: Probing media device '/dev/media0'
cros_camera_service[4755]: Probing sensor 'ov13b10 11-0036' (v4l-subdev17)
cros_camera_service[4755]: Found V4L2 sensor subdev on /sys/devices/pci0000:00/0000:00:15.2/i2c_designware.2/i2c-11/i2c-OVTIDB10:00/video4linux/v4l-subdev17
Change-Id: I6a82557c94203f24449588a6005abc53cc29ca76
Signed-off-by: Weimin Wu <wuweimin@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79163
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arec Kao <arec.kao@intel.corp-partner.google.com>
|
|
Intel CNVi WLAN's BT uses USB2 Port 10 inside the SOC,
and the relevant configuration needs to be modified in overridtre.cb.
BUG=b:304920262
TEST=lsusb
ID 8087:0033 Intel Corp.
rfkill list
hci0:Bluetooth
Change-Id: Ibcae800836c17307bc133de5a91658f6dda5985c
Signed-off-by: Weimin Wu <wuweimin@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79055
Reviewed-by: Eric Lai <ericllai@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Anraggar cannot boot into OS and kernel loading failure.
Update eMMC DLL values to improve initialization reliability
- Sending different speed TX/RX command/data signal to eMMC and check
the response is success or not.
- Collecting every eMMC that use for the project
- Based on above result to provide a fine tune DLL values
BUG=b:308366637
TEST=Cold reboot stress test over 2500 cycles
Change-Id: I9ec3cc23000301aa72aed96e74b63114623c4fc2
Signed-off-by: Simon Yang <simon1.yang@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78851
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
OpenSIL has an API to call back into the host firmware to print to the
console.
These could be moved to a common directory when there are more openSIL
implementations to see if it is actually common.
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Signed-off-by: Martin Roth <gaumless@gmail.com>
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I208eea37ffde64a2311cb9f51e2bcd1ac3dbad4d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76512
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-by: Varshit Pandya <pandyavarshit@gmail.com>
|
|
As customer demand, it is necessary to set MSR Package Power Limit-1 to 17W for the DTT setting to optimize performance.
The PL1 value (17W) suggested by the thermal team which is different from the reference code(PL1=15W).
BUG=b:312321601
BRANCH=firmware-brya-14505.B
TEST=emerge-brya coreboot chromeos-bootimage
Built and booted into OS, and confirm MSR PL1=17W correctly.
Change-Id: If7874d26038118c5605cf0721c30e681b45123fe
Signed-off-by: Daniel Peng <Daniel_Peng@pegatron.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79335
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Daniel Peng <daniel_peng@pegatron.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch moves the SOC_INTEL_STORE_ISH_FW_VERSION config from the
Nissa baseboard to BOARD_GOOGLE_BRYA_COMMON. This allows all baseboards
to retrieve the ISH version and store it into memory.
Ensure SOC_INTEL_STORE_ISH_FW_VERSION is enabled only for platforms
with ISH support (DRIVERS_INTEL_ISH).
Additionally, the dedicated SOC_INTEL_STORE_ISH_FW_VERSION config
selection for the Nissa baseboard is no longer needed.
BUG=b:280722061
TEST=Able to build and boot google/marasov.
Change-Id: I99dab43ae4e13869b7f8797a9c4014f60e38a595
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79338
Reviewed-by: Eric Lai <ericllai@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
|
Change GPP_B14 from NC to NF
BUG=b:272447747
TEST=enable usb OC2 function to ensure USBA work normal
Change-Id: Ie0f112bcf183870869d0c1b9a223d4231600a300
Signed-off-by: Kun Liu <liukun11@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79308
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Rui Zhou <zhourui@huaqin.corp-partner.google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
|
|
On Brox, TPM is using i2c4 and GPP_E2, so modifying the Kconfig to
reflect this. Also, fixing up the TPM entry in the device tree.
Making sure that the GPIO for GSC_PCH_INT_ODL is set correctly.
BUG=b:300690448
BRANCH=None
TEST=emerge-brox coreboot
Change-Id: I0ecaa6fcfc05c3c2e55f857d7a4e59fe46096bb5
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79102
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Ivy Jian <ivy.jian@quanta.corp-partner.google.com>
|
|
We seem to be passing CPPFLAGS to linker in x86 arch
ramstage. This is superflous as these are only meant
to be compiler flags and should not be passed to the
linker.
Change-Id: Ia3cd51be6be252aa796191cf0d2cd91d393c8878
Signed-off-by: Srinivas Hegde <srinivashegde@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79218
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Jérémy Compostella <jeremy.compostella@intel.com>
|
|
Select PSP_VERSTAGE_MAP_ENTIRE_SPIROM in Cezanne Kconfig instead of
common Kconfig.
BUG=None
TEST=Build BIOS image and boot to OS in dewatt.
Change-Id: I476971700824fed06d17000001afc075105fa1ee
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79306
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Tim Van Patten <timvp@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Earlier entire SPI ROM was mapped to memory. With limited TLB resources
in PSP, this approach hit the limit on systems using 32 MiB SPI ROM.
Therefore regions in SPI ROM were mapped on need basis. This works well
on Picasso, Mendocino and Phoenix SoCs. But unfortunately this causes
boot hangs in Cezanne SoC. Add a configuration to map the entire SPI ROM
and enable it in Cezanne SoC. For other SoCs, keep the configuration
disabled so that only the required SPI ROM region is mapped.
BUG=b:309690716
TEST=Build and boot to OS in both Dewatt and Skyrim.
Change-Id: I166ac7b50b367c067e1a743fc94686e69dd07844
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79155
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Tim Van Patten <timvp@google.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Select opensil & opensil_genoa. This enables openSIL for Genoa, allowing
the build to be tested.
Change-Id: I18379f311a56ff3f8b68d3c9a07a4f59de2d90b2
Signed-off-by: Martin Roth <gaumless@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78635
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Varshit Pandya <pandyavarshit@gmail.com>
|
|
OpenSIL has a native buildsystem using meson and configuration mechanism
using kconfiglib.
To be able to use the coreboot toolchain with opensil, meson crossfiles
are used, which get generated by coreboot makefiles.
Configuration of opensil is done in a similar fashion with a template
defconfig after which kconfiglib is called to generate headers.
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Signed-off-by: Martin Roth <gaumless@gmail.com>
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ide2d181914116119dfd37b1511d89ea965729141
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76511
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Varshit Pandya <pandyavarshit@gmail.com>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
|
|
Adjust ACPI DSDT to support ECAM resource above 4GB by modifying the PCI
ECAM Resource Consumption settings. The changes include specifying a
QWordMemory resource template, accommodating non-cacheable, read-write
attributes, and adjusting the address range.
Change-Id: Idb049d848f2311e27df5279a10c33f9fab259c08
Signed-off-by: Naresh Solanki <naresh.solanki@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79096
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Reviewed-by: Maximilian Brune <maximilian.brune@9elements.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Add taeko new supported memory parts in mem_parts_used.txt, generate
spd-3.hex for these parts.
1. Samsung K4UBE3D4AB-MGCL
2. Micron MT53E1G32D2NP-046 WT:B
BUG=b:312363368
TEST=Use part_id_gen to generate related settings
Signed-off-by: Leo Chou <leo.chou@lcfc.corp-partner.google.com>
Change-Id: I221ad3f490f24b43fe1ccd211014787eab5d1038
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79184
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Bob Moragues <moragues@google.com>
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: YH Lin <yueherngl@google.com>
|
|
Drop code that puts Super I/O into config mode, select serial device,
then leave config mode right away having done nothing.
I'll also take this chance to revise its #includes based on
include-what-you-use results.
Change-Id: I304fc1610740375b59121b6b8784122440795838
Signed-off-by: Keith Hui <buurin@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73693
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Board was not producing serial output until well into ramstage.
To fix, select SUPERIO_NUVOTON_COMMON_COM_A Kconfig to tell
nuvoton_enable_serial() to route serial port A signals to the outside,
not GPIO8x.
TEST=Full native raminit debug log received over serial by minicom.
Change-Id: I376a79dd76ffa5f4d47e7c0cb53680e173e1ad78
Signed-off-by: Keith Hui <buurin@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79222
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Enable BT audio offload of ALC1019_ALC5682I_I2S based on fw_config.
BUG=b:299510759
TEST=Build and boot to Screebo. Verify the config from serial logs.
w/o this CL -
```
[SPEW ] ------------------ CNVi Config ------------------
[SPEW ] CNVi Mode = 1
[SPEW ] Wi-Fi Core = 1
[SPEW ] BT Core = 1
[SPEW ] BT Audio Offload = 0
[SPEW ] BT Interface = 1
```
w/ this CL -
```
[SPEW ] ------------------ CNVi Config ------------------
[SPEW ] CNVi Mode = 1
[SPEW ] Wi-Fi Core = 1
[SPEW ] BT Core = 1
[SPEW ] BT Audio Offload = 1
[SPEW ] BT Interface = 1
```
Signed-off-by: Kapil Porwal <kapilporwal@google.com>
Change-Id: I6c713752f3f0bf58b5ebd78b904e773fdbf16e06
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77755
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Wentao Qin <qinwentao@huaqin.corp-partner.google.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
|
Add PIXA touchpad for variants of craask.
BUG=b:310489697
TEST=build craask firmware and test with PIXA touchpad
Change-Id: I7e68a44eb3d639eaadb5b7b9cb5a6955fd059eeb
Signed-off-by: Tyler Wang <tyler.wang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79212
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Ren Kuo <ren.kuo@quanta.corp-partner.google.com>
Reviewed-by: David Wu <david_wu@quanta.corp-partner.google.com>
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
|
This follows commit c79e96b4eb3 which did the rename across the tree
except in these places. Remove the flag from CHROMEOS abuild builds
because it never really belonged there.
Change-Id: If98fa27f64d6b676d3edf68ba6fbaacf7ac422e4
Signed-off-by: Patrick Georgi <patrick@coreboot.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79258
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
|
|
Also update the regular expression to find the genoa blobs.
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Change-Id: Iba0109c049019a22cba1e0358cedbd9c198c6569
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76525
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
In nissa platform, we configured GPP_F17 as SCI+APIC to wake the system
and also generate IRQ to the IOAPIC. Currently, we set GPP_F17 to level
triggered and it causes AP (Application Processor) to keep sending
GET_NEXT_EVENT to EC during resume from suspend by connecting AC.
So we change GPP_F17 to edge triggered to avoid this condition.
BUG=b:308716748
TEST=Original failure rate was 7 out of 10 times and it reduced to
0 out of 60 times on six joxer systems.
Signed-off-by: Scott Chao <scott_chao@wistron.corp-partner.google.com>
Change-Id: I3ceb1dfce46376a6a9a8c6cb6d691d818a0a42ff
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79244
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Eric Lai <ericllai@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Reka Norman <rekanorman@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
|
Without this it would use the exception handler from the previous
stage.
Change-Id: I79d875aca6cd0cffe482e4ebb5f388af0adf6aed
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68840
Reviewed-by: Maximilian Brune <maximilian.brune@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Change-Id: Id9e4adcd976e1f56ef7f502d9df16dbefce95c3e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79217
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Tim Wawrzynczak <inforichland@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Probe usb ports by FW_CONFIG setting to disable C1 port on quandiso new daughterboard without C1 port.
BUG=b:312094048
BRANCH=firmware-nissa-15217.B
TEST=emerge-nissa coreboot
Change-Id: I6f702f60c772176e80b3452bf957d10625564102
Signed-off-by: Robert Chen <robert.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79173
Reviewed-by: Eric Lai <ericllai@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable 3VSBSW# in NCT6779D super I/O like other variants in the family,
needed to maintain power to memory during S3 suspend. Without it
resuming totally fails.
(Enabling it in devicetree is OK; it needs not be done in early
board init.)
TEST=Resuming from S3 works.
Change-Id: Ia8059b2a263ab5c459e54685f046eeb913776473
Signed-off-by: Keith Hui <buurin@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78205
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Kevin Keijzer <kevin@quietlife.nl>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The DPTF parameters were defined by the thermal team.
Based on thermal table in 290705146#comment17.
BUG=b:290705146
BRUNCH=firmware-nissa-15217.B
TEST=emerge-nissa coreboot chromeos-bootimage
Change-Id: I02b4187000eec9990bf10a57875b23007f7bdd12
Signed-off-by: Van Chen <van_chen@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79183
Reviewed-by: Eric Lai <ericllai@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch enables the FSP (Firmware Splash Screen) rendering feature
for all Rex variants, including chromeboxes like Ovis. This will allow
users to see the FSP logo during the boot process.
BUG=b:284799726
TEST=Verify that the FSP logo is displayed during the boot process on
an google/ovis chromebox.
Change-Id: I73d82e16f70ffdc8cb168506c86d9c4e9a92c38d
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79175
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
Set pen detect pin to NC base on fw_config.
BUG=b:304680060
TEST=emerge-rex coreboot pass
Change-Id: Icf9171fca49cfed1a05a67ae7fc8d62b7e9630c9
Signed-off-by: Tyler Wang <tyler.wang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79213
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The Genoa SoC has 6 I2C controllers. In order to support those, select
SOC_AMD_COMMON_BLOCK_I2C and implement the SoC-specific functions and
data structures needed by the common AMD I2C code. Since the common AMD
I2C code also reports if the controller is enabled or not in the SSDT,
change the corresponding DSDT code to use this information. In this
patch the I2C pad control registers don't get configured by coreboot yet
and we rely on ABL already having those set up correctly which seems to
be an assumption that the reference firmware is making too. PPR #55901
Rev 0.26 was used as a reference for the I2C controllers and the GPIO
pins being used.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Iebc10de6ea5c6d441cff04e016dcec62405078c3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78900
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Varshit Pandya <pandyavarshit@gmail.com>
|
|
The code for "phase 4" of firmware verification currently only sets a
recovery reason when there's an actual hash mismatch detected in
vb2api_check_hash_get_digest(). This is the most likely way how this
section of code can fail but not the only one. If any other unexpected
issue occurs, we should still set a recovery reason rather than just
reboot and risk an infinite boot loop.
This patch adds a catchall recovery reason for any error code that falls
out of this block of code. If a more specific recovery reason had
already been set beforehand, we'll continue to use that -- if not, we'll
set VB2_RECOVERY_FW_GET_FW_BODY.
Change-Id: If00f00f00f00aa113e0325aad58d367f244aca49
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78866
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch tries to standardize and simplify the Kconfig option layout
for Google boards with MediaTek SoCs and align them to the scheme used
with other Arm-based Google boards.
Change-Id: I40880e7609ba703d0053ad01da742871e54d4e7a
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79063
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yidi Lin <yidilin@google.com>
|
|
This patch unifies and simplifies the Kconfig selection model for the
Gru, Herobrine, Trogdor and Veyron boards according to the model
discussed in CB:78972.
Also add missing license headers to two Kconfig files while I'm here.
Change-Id: If679a05afd10869afba9c2a33b54862e102b5f40
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79022
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
While transitioning the devicetree to make use of the chipset
devicetree, commit 3b5b9f4c543c ("mb/hp/280_g2: Make use of the chipset
devicetree") removed useful comments documenting the endpoints of the
root ports. Restore them.
Change-Id: I178cb472a8f40baaccc30514689bda2730dfa9dc
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79153
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
This patch guarantees that non-ChromeOS platforms continue to enable
early caching.
ChromeOS devices, on the other hand, control this configuration through
the motherboard configuration based on the underlying SoC.
BUG=b:306677879
TEST=Enable SOC_INTEL_COMMON_BASECODE_RAMTOP for google/rex.
Change-Id: I412b2b6a807dc0f5f2632f0fbd56bd37689dead3
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79049
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
|
|
This patch enables the `SOC_INTEL_COMMON_BASECODE_RAMTOP` config
option for select mainboards, as not all board variants may want to
enable this config due to underlying SoC dependencies.
Mainboards that attempt to enable early caching have exhibited soft
hangs while switching between pre-RAM and post-RAM phases. This patch
allows mainboards to choose to enable this option without enabling
it by default (which could cause boot hangs).
Furthermore, it reorganizes the configuration options under
BOARD_GOOGLE_BASEBOARD_REX in alphabetical order for better readability.
BUG=b:306677879
TEST=Enable SOC_INTEL_COMMON_BASECODE_RAMTOP for google/rex and
intel/mtlrvp.
Change-Id: If380c2ecbee4f6437c3d58bfb55be076a4902997
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79048
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
|
|
Follow thermal validation, add ldo output select for speaker.
BUG=b:297298847
TEST=emerge-nissa and deploy to DUT to verify audio functionality.
Change-Id: Ie68f2b35f024b4dd066d831ae8fd5a662d407753
Signed-off-by: Terry Chen <terry_chen@wistron.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79111
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Derek Huang <derekhuang@google.com>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
This partially reverts commit f493857c9bc1 ("mb/google/brya/var/*: Set
dGPU/LAN/WLAN device type to generic"). Setting the LAN device type to
generic broke programming the LAN MAC address, so set it back to pci.
TEST=build/boot google/brya (osiris), verify LAN MAC address programmed
correctly.
Change-Id: I4fb43b7212e67b5c38724baad572860bc45b558e
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79150
Reviewed-by: Eric Lai <ericllai@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This mostly reverts commit 6c705e766f7f ("mb/google/puff/var/*: Set
LAN/WLAN device type to generic"). Setting the LAN device type to
generic broke programming the LAN MAC address, so set it back to pci.
TEST=build/boot google/puff (wyvern), verify LAN MAC address programmed
correctly.
Change-Id: I558ae6dc1366d5a8a22e0383d7d597d15159df03
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79149
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
Arrange ACPI table enum in a vertical and alphabetized format.
This change aims to reduce conflicts between patches.
Change-Id: I192339df771d6a3ae67358fe46334fe2b216b974
Signed-off-by: Naresh Solanki <naresh.solanki@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79099
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Reviewed-by: Maximilian Brune <maximilian.brune@9elements.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Instead of using MSR IA32_PLATFORM_ID read the SystemAgent device id
to figure out the PC type. This follows the BWG which suggest to not
use MSR IA32_PLATFORM_ID for system identification.
Tested: Lenovo X220 still boots.
Change-Id: Ibddf6c75d15ca7a99758c377ed956d483abe7ec1
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78826
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Now that those registers are only written once set the lock bit to
protect it from runtime changes.
TEST: Lenovo X220 still boots.
Change-Id: I4c56a3cb322a0e75eb3dd366808068093928e10c
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78608
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Write MSRs that are in scope package only once by checking for the BSP
bit. While this improves performance a bit it also has the benefit
that registers can be safely locked down without the need for
semaphores.
TEST: Lenovo X220 still boots.
Change-Id: I43f5d62d782466d2796c1df6015d43c0fbf9d031
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78607
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
commit 1e9601c5ef80 ("nb/intel/sandybridge: Standardize MRC vs. native
SPD mapping API") introduced an uninitialized variable issue.
Change-Id: I41b081dc4c961acc04423067e29e0eabe5f17539
Found-by: Coverity CID 1524317
Signed-off-by: Jeremy Compostella <jeremy.compostella@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79093
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <patrick.rudolph@9elements.com>
|
|
Check FW_CONFIG and disable gpios for HPS if HPS_ABSENT for skolas
and brya0 variants.
BUG=b:311740746
BRANCH=firmware-brya-14505.B
TEST=`emerge-brya coreboot chromeos-bootimage`, flash and boot skolas
to kernel and verify via "cbmem -c | grep HPS".
Change-Id: I8cbe4f40c41f1d06e8f511c3e88c05984566d441
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79123
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
Check FW_CONFIG and disable gpios for LTE if LTE_ABSENT for skolas
and brya0 variants.
BUG=b:311459627
BRANCH=firmware-brya-14505.B
TEST=`emerge-brya coreboot chromeos-bootimage`, flash and boot skolas
to kernel and verify LTE gpios are disabled via "cbmem -c | grep LTE".
Change-Id: I3f3bc2b536babf71cc484cce02f96f47707f729c
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79122
Reviewed-by: Eric Lai <ericllai@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Skolas uses brya0 schematic, so override tree should be almost the same
for brya0 and skolas. This change sync's the skolas overridetree.cb
with brya0's overridetree.cb.
BUG=b:311722825
BRANCH=firmware-brya-14505.B
TEST=`emerge-brya coreboot chromeos-bootimage`, flash and boot skolas to
kernel.
Change-Id: I14a2ed803a8ffb8614018af587c66034fb724b38
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79121
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
This changes the path where go installs its packages.
Now the packages are not installed in the users home directory anymore.
This solution is not perfect though, since offline build are still not
possible, because go will fetch the packages at build time.
-modcacherw will create the go files with rw permissions, otherwise
coreboot is not able to delete the files afterwards (make distclean).
Signed-off-by: Maximilian Brune <maximilian.brune@9elements.com>
Change-Id: I2a35369628454057ea4758cd1225e57f07cb71c8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77780
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
|
|
According to eDP panel datasheet[1], the eDP panel needs 0 <= x <=200ms
delay after VDD powering on. The MIPI panel[2] does not need this delay.
Move this delay to eDP path.
[1] NE135FBM-N41 V8.0 Product Spec_P2 20191025.pdf
[2] B5 TV110C9M-LL0 Product Specification Rev.P0
BRANCH=none
BUG=none
TEST=check FW screen
TEST=check timestamp
Before:
60:device initialization 696,422 (1)
15:starting LZMA decompress (ignore for x86) 696,587 (165)
16:finished LZMA decompress (ignore for x86) 696,675 (88)
17:starting LZ4 decompress (ignore for x86) 1,340,226 (643,551)
After:
60:device initialization 724,259 (1)
15:starting LZMA decompress (ignore for x86) 724,425 (166)
16:finished LZMA decompress (ignore for x86) 724,512 (87)
17:starting LZ4 decompress (ignore for x86) 1,168,176 (443,664)
Change-Id: I92bca5ec8269f4bad4dfab4ee193cdb5665de233
Signed-off-by: Yidi Lin <yidilin@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79109
Reviewed-by: Ruihai Zhou <zhouruihai@huaqin.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
|
Since the HD audio controller in the PCH are always on the same device
functions, the device operations can be statically assigned in the
devicetree and there's no need to bind the host bridge device operations
to the PCI device during runtime via a list of PCI IDs.
TEST=Lenovo X220 still boots to Linux and audio still works
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Change-Id: I9bbbe9f4490dc6fb21174d63d1c8906d69ea3ee0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79118
Reviewed-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Since the PCIe root ports in the PCH are always on the same device
functions, the device operations can be statically assigned in the
devicetree and there's no need to bind the host bridge device operations
to the PCI device during runtime via a list of PCI IDs.
TEST=Lenovo X220 still boots to Linux and all PCIe devices on PCH are
visible and working.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Change-Id: I05bfe8db88fd54415f320f32ea147636ca4e0df8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79117
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <patrick.rudolph@9elements.com>
|
|
Since the integrated GPU is always function 0 of device 2 on bus 0, the
device operations can be statically assigned in the devicetree and
there's no need to bind the host bridge device operations to the PCI
device during runtime via a list of PCI IDs.
TEST=Lenovo X220 still boots to Linux and graphics works in UEFI
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Change-Id: I20e387e626e19dc441aceda18451186d1e86cd5f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79114
Reviewed-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Since the host bridge is always function 0 of device 0 on bus 0, the
device operations can be statically assigned in the devicetree and
there's no need to bind the host bridge device operations to the PCI
device during runtime via a list of PCI IDs.
TEST=Lenovo X220 still boots to Linux
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Change-Id: Icf3d9f8cd2be2f8ef71fd9fdb5f005f3b683332e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79113
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <patrick.rudolph@9elements.com>
|
|
Brox is using Ti50, so make sure that we set the right config for that.
BUG=b:300690448
BRANCH=None
TEST=emerge-brox coreboot
Change-Id: If4a16448eebc028b2989c1de150b9e0f9067ee92
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79100
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
Assigning the macros in gpio.h to the correct GPIOs. Also, fixing GPE
configurations so that they are mapped to the proper wake sources
(GPP_B, D, E groups).
BUG=b:300690448
BRANCH=None
TEST=emerge-brox coreboot
Change-Id: I6320cd98e560e514e63c52e173cb7923cfd1cdee
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78952
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
We need to increase romstage size a little to make a compiler upgrade
fit (CB:70771). Unfortunately the end of the romstage directly touches
the QCSDI region in the current memlayout, and there is no other way
to reshuffle things to make more space... so we need to move QCSDI out
of the way. This means that anyone who is actually building this
platform with CONFIG_QC_SDI_ENABLE (which requires a proprietary blob
that's not publicly available) will need to recompile their QCSDI binary
to match the new start address.
Change-Id: Iaf13e4001b3c763e3ec59009779931ec75603d5d
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79074
Reviewed-by: Shelley Chen <shchen@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
|
Selects should be done in the Kconfig file instead of Kconfig.name and
not mixed over both files.
Change-Id: I25b7adccf60abe515d129f8d00383165eccf6431
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79028
Reviewed-by: Martin L Roth <gaumless@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Selects should be done in the Kconfig file instead of Kconfig.name and
not mixed over both files.
Change-Id: I30a15277527a1e423691ff55ff11cc2136cefc90
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79027
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
|
|
Building coreboot for the Qualcomm SoCs SC7180 and SC7280 requires to
include the Qualcomm blobs, which requires to accept their license.
However, for various reasons it makes sense to build without blobs, e.g.
static analysis or just build-testing.
So in order to do that, run the steps integrating the Qualcomm blobs
into the coreboot binary only if USE_QC_BLOBS is enabled and also remove
guards which prevent building related mainboards when USE_QC_BLOBS is
not enabled.
Change-Id: I249ac477b8f10e7fa0848e967c23a3b3b9bbd27d
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79026
Reviewed-by: Martin L Roth <gaumless@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add the CPU and PCI domain operation bindings statically in the chipset
devicetree instead of adding them during runtime.
TEST=PC Engines APU2 still boots and doesn't show any new problems
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I44fa57458c408e74a6341643620c5e9ac1817557
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79085
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Since this chip is a SoC and also to bring the chipset devicetree more
in line with the chipset devicetree of Sandy Bridge, merge the chip
operations of the northbridge's root complex and the northbridge itself
into one chip operations structure and use it at the top level of the
devicetree.
TEST=PC Engines APU2 still boots and doesn't show any new problems
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I8b42bac07b1409bbc797bc4428cf9f84a40e94c2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79084
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
|
|
BKDG #52740 Rev 3.05 was used as a reference for the SoC's various PCI
devices. The HDA controller in the FCH at function 2 of device 0x14 on
bus 0 was missing in the mainboard's devicetrees.
TEST=PC Engines APU2 still boots and doesn't show any new problems
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I6970c2f6e6d661d40406586f4e6eeb05bcd07979
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79083
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
|
|
There's no need to remove the corresponding fields from the
device_operations struct when HAVE_ACPI_TABLES isn't selected.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Iac20b6cdc44a5280566ee7003a5ef6fbe913b099
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78990
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
There's no need to remove the corresponding fields from the
device_operations struct when GENERATE_SMBIOS_TABLES isn't selected.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ifa24d1fd211c263b788046e63de3dd5c54cba801
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79092
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
|
|
Configure I2S1 and I2C5 for ALC5650 to support beep sound in
depthcharge.
BRANCH=corsola
BUG=b:305828247
TEST=Verify devbeep in depthcharge console
Change-Id: Ibd098adb8d5568ad338bbfece0edfd0c38cbf854
Signed-off-by: Yang Wu <wuyang5@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79064
Reviewed-by: Yidi Lin <yidilin@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Ruihai Zhou <zhouruihai@huaqin.corp-partner.google.com>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
Morphius boards using pre-v3.6 schematics don't have a dedicated GPIO
for touchscreen power/enable, and so fail with runtime detection
enabled. Since it only has one touchscreen option, and no SKUs lack a
touchscreen, we can safely assume it is present in all cases.
TEST=build/boot morphius w/4k screen, verify touchscreen enabled in
cbmem and functional in Linux and Windows.
Change-Id: I13e07e14b5a18fa1dd3b18950cf46e9d7821eedc
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78404
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Generated using update_ec_headers.sh [EC-DIR].
The original include/ec_commands.h version in the EC repo is:
ab9b64ac4c Add a host command to print info about AP-firmware state
The original include/ec_cmd_api.h version in the EC repo is:
ab9b64ac4c Add a host command to print info about AP-firmware state
BUG=b:300525571
BRANCH=none
TEST=none
Change-Id: I3570e073a91621cb1d28a24aa35c1f4beedceaab
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79066
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Returning a NULL device name can cause issues if something else does
handle it.
E.g. UART and GNA devices on Intel Alder Lake-N cause
INTERNAL_POWER_ERROR BSOD's in Windows when enabled due to invalid
packages being created from a NULL name
Test: build/boot google/nissa (craaskvin) to Win11
Change-Id: I0679147ad3e330d706bbf97c30bc11b2432e2e8a
Signed-off-by: CoolStar <coolstarorganization@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77413
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
|
|
Appears to not be used under Windows, Linux, or ChromeOS, and causes
high CPU usage at idle under Windows.
BUG=none
TEST=build/boot Win11, Linux on google/frostflow, verify camera shutter
function unchanged, CPU usage under Windows idles where expected.
Change-Id: I8a6ea3b886766bdb055b40949c75bec0264eecc5
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77678
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
System76 only sells units with memory speeds up to 5200 MT/s, but the
i9-13900HX supports up to 5600 MT/s memory.
Tested by running memtest and checking dmidecode reports 5600 MT/s when
using 2x16 GB 5600 MT/s Crucial SODIMMs (CT2K16G56C46S5) on addw3,
bonw15, serw13.
Change-Id: I9bb0435769c70c1db06d2c5cca2dd28eb5331f49
Signed-off-by: Matt Parnell <mparnell@gmail.com>
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Tested-by: Levi Portenier <levi@system76.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78912
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Use the references from the chipset devicetree as this makes the
comments superfluous and remove devices which are turned off.
Change-Id: I5176aa56ecaa52d0f42455bc7176b0415a6199ec
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78594
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
According to proto schematics, the SD card is removed.
BUG=b:308968270
TEST=emerge-geralt coreboot
BRANCH=None
Change-Id: Id4e021e7896d093560f39c40573ac616d76438c2
Signed-off-by: Ruihai Zhou <zhouruihai@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78958
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: cong yang <yangcong5@huaqin.corp-partner.google.com>
Reviewed-by: Yidi Lin <yidilin@google.com>
|
|
These backlight related functions can be reused in other variants, move
them out to the panel.c. Also the panel_geralt.c should be used for
Geralt, enable it on Geralt board only.
BUG=b:308968270
TEST=emerge-geralt coreboot
BRANCH=None
Change-Id: I5d4035d5f480551c428c450826e23bf77f2fe08a
Signed-off-by: Ruihai Zhou <zhouruihai@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78955
Reviewed-by: Yidi Lin <yidilin@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: cong yang <yangcong5@huaqin.corp-partner.google.com>
|
|
This uses the size attribute to traverse the possible string.
This patch traverses the entire property for non printable characters
and not just until the first 0 is hit.
Now numbers that start with a zero (memory wise) are not falsely
recognized as strings:
before the patch:
clock-frequency = "";
after the patch:
clock-frequency = < 0x1c2000 >;
Signed-off-by: Maximilian Brune <maximilian.brune@9elements.com>
Change-Id: I229c07b76468fe54f90fa9df12f103d7c7c2859d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78025
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
BUG=none
TEST=build karis firmware pass
Change-Id: I67b4ca4c8fde795d4206eaa0b9ea9d9bfc768ac6
Signed-off-by: Tyler Wang <tyler.wang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79053
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: David Wu <david_wu@quanta.corp-partner.google.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
|
Create the variant Ciri and enable MAX98390 AMP for it. The panel
related support will be added in the follow up CLs.
BUG=b:308968270
TEST=emerge-geralt coreboot
BRANCH=None
Change-Id: I7bbe9ed5e722a70bab1c799a61ce38d2ad58ab25
Signed-off-by: Ruihai Zhou <zhouruihai@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/78954
Reviewed-by: Yidi Lin <yidilin@google.com>
Reviewed-by: cong yang <yangcong5@huaqin.corp-partner.google.com>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
|
|
This patch creates a new variant mtlrvp4es_p_ext_ec. The new
variant will support ESx samples. The existing mtlrvp_p_ext_ec
variant will support the QS samples.
BUG=b:310775573
TEST= Build and boot mtlrvp4es_p_ext_ec.
Signed-off-by: Usha P <usha.p@intel.com>
Change-Id: Iad72c0f6343af149d16d8b1f8639ba496f6aab0c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79052
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
|
|
This patch sets the default locales to English for platforms that
do not have support for VBOOT configuration. This ensures that the
system will use English locales if the platform does not provide
its own locale settings.
TEST=Built and booted the google/rex platform successfully.
Change-Id: I7554c8bfd58411f460deeb22cf7218059ca8ba9f
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79054
Reviewed-by: Hsuan-ting Chen <roccochen@google.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jérémy Compostella <jeremy.compostella@intel.com>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Update power limit values based on the suggestion of the thermal
team for RPL CPU.
The PL1 value (28W) suggested by the thermal team which is different from the reference document 686872 (PL1=15W).
BUG=b:310834985
TEST=built and booted into OS.
Change-Id: Ia2540ecd1fc453701b9160c97d82ba50b88ee848
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79059
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Eric Lai <ericllai@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This is already handled as a separate case in the code below, so there's
no need for this assert any more.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I7511ec5683a924dc289faa2b9fabd0e8714d291e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79047
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Use a define instead of magic numbers.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I2c6d17bd78a0e207f9130102b43ba78aa55ce377
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79046
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
