summaryrefslogtreecommitdiff
path: root/src
AgeCommit message (Collapse)Author
2014-02-27baytrail: use MCRX in iosf access functionsAaron Durbin
While most registers accesses don't need the use of the MCRX register (upper 24 bits of address) the MCRX register should be protected. The reference code could be doing accesses to registers that initialized the MCRX register. Thus, any access after that should ensure the MCRX register is initialized appropriately. BUG=None BRANCH=None TEST=Verified assembly output. Also, built and booted through depthcharge. Change-Id: I4d6cfbe6bb1666790c69778b8f2c8baeaf015264 Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: https://chromium-review.googlesource.com/174643 Reviewed-by: Shawn Nematbakhsh <shawnn@chromium.org> Reviewed-on: http://review.coreboot.org/4909 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
2014-02-25Kill ALT_CBFS_LOAD_PAYLOADVladimir Serbinenko
Not used anymore. Change-Id: Icf3a4a7f932776981048b805478582ad2b784182 Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com> Reviewed-on: http://review.coreboot.org/5132 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@google.com> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2014-02-25lynxpoint: Kill alternative cbfs_load_payload.Vladimir Serbinenko
With generic load using 32-bit accesses this is no longer has a huge impact it previously did. It's also unnecessarily component-speficific. Change-Id: I7e8a74ea1ceaa225e1024f9eb43e7280773e2b5a Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com> Reviewed-on: http://review.coreboot.org/5131 Reviewed-by: Aaron Durbin <adurbin@google.com> Tested-by: build bot (Jenkins) Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
2014-02-25Remove CACHE_ROM.Vladimir Serbinenko
With the recent improvement 3d6ffe76f8a505c2dff5d5c6146da3d63dad6e82, speedup by CACHE_ROM is reduced a lot. On the other hand this makes coreboot run out of MTRRs depending on system configuration, hence screwing up I/O access and cache coherency in worst cases. CACHE_ROM requires the user to sanity check their boot output because the feature is brittle. The working configuration is dependent on I/O hole size, ram size, and chipset. Because of this the current implementation can leave a system configured in an inconsistent state leading to unexpected results such as poor performance and/or inconsistent cache-coherency Remove this as a buggy feature until we figure out how to do it properly if necessary. Change-Id: I858d78a907bf042fcc21fdf7a2bf899e9f6b591d Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com> Reviewed-on: http://review.coreboot.org/5146 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@google.com>
2014-02-24intel/*/acpi: Increase range length of MCHBAR buffer to 32 kBPaul Menzel
Linux kernel 2.6.31 reports the warning below on Intel Ivy Bridge (with FSP). resource map sanity check conflict: 0xfed10000 0xfed17fff 0xfed10000 0xfed13fff pnp 00:01 Since Sandy Bridge the length of the MCHBAR is 32 kB and it is already used that way in other places. $ more src/northbridge/intel/fsp_sandybridge/acpi/hostbridge.asl […] OperationRegion (MCHB, SystemMemory, DEFAULT_MCHBAR, 0x8000) […] So instead of 16 kB specify that 32 kB are decoded in that memory range for Intel Sandy Bridge, Ivy Bridge and Haswell. (Linux kernel 3.10 does not warn about that.) Change-Id: Ie7a9356d9051c807833df85e4a806e5a9498473f Reported-by: Norwich in #coreboot on <irc.freenode.org> Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-on: http://review.coreboot.org/5192 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@google.com> Reviewed-by: Werner Zeh Reviewed-by: Marc Jones <marc.jones@se-eng.com>
2014-02-24baytrail: Enable GFX deviceDuncan Laurie
- Ungate display in PUNIT - Set GSM to 64MB since 32MB is not supported in <C0 stepping - Initialize power management registers in GTT - Execute VBIOS if found BUG=chrome-os-partner:23507 BRANCH=rambi TEST=build and boot to dev screen via HDMI on rambi Change-Id: Idb032c7ea7f16b651b4c921e3429a652fe663a5d Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: https://chromium-review.googlesource.com/174922 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: http://review.coreboot.org/4907 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2014-02-24baytrail: IOSF write functions need to set data before controlDuncan Laurie
The data needs to be available in the register before the control bits are set to make the write happen. BUG=chrome-os-partner:23507 BRANCH=rambi TEST=successfully ungate power on PUNIT on rambi Change-Id: I8fae60d5385ce9a401c1dec9cbb39b70d157a6c2 Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: https://chromium-review.googlesource.com/174898 Reviewed-by: Stefan Reinauer <reinauer@chromium.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: http://review.coreboot.org/4906 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2014-02-24rambi: add chromeos EC supportAaron Durbin
As rambi has the ChromeOS EC on it the EC needs to be configured properly. Do this along with updating the ChromeOS support for passing on write protect state, recovery mode and developer mode. BUG=chrome-os-partner:23387 BRANCH=None TEST=Built and booted to depthcharge. EC software sync appears to work correctly. Additionaly, 'mainboard_ec_init' appears in the console output. Change-Id: I40c5c9410b4acaba662c2b18b261dd4514a7410a Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: https://chromium-review.googlesource.com/174714 Reviewed-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: http://review.coreboot.org/4905 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2014-02-24baytrail: initialize chromeos EC if present in romstageAaron Durbin
The EC needs to be initialized early in romstage. Therefore perform the call after console has been initialized in order to view any messages that the code may spit out. BUG=chrome-os-partner:23387 BRANCH=None TEST=Built and booted with recovery mode and EC in RW. Noted that system reboots the EC. Change-Id: I35aa3ea4aa3dbd9bd806b6498e227f45ceebd7a1 Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: https://chromium-review.googlesource.com/174713 Reviewed-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: http://review.coreboot.org/4904 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2014-02-24baytrail: use version 2 of efi wrapperAaron Durbin
Version 2 of the efi wrapper wants the speed of the TSC timer initialized in the parameter structure. BUG=chrome-os-partner:22866 BRANCH=None TEST=Built and booted through depthcharge. No errors spit out by wrapper. CQ-DEPEND=CL:*147256 Change-Id: I9cd265ea6bde93be85fc6fbc905d83af57fc2773 Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: https://chromium-review.googlesource.com/174712 Reviewed-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: http://review.coreboot.org/4903 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2014-02-24baytrail: remove gfx read_resources() work aroundAaron Durbin
Before the special PUNIT settings the GFX pci device had the same device id as the transaction router. This required a special case in the transaction router's driver to do the proper thing for read_resources(). However, that requirement is no longer needed as the PUNIT special message is now being done. Therefore, remove the work around. BUG=None BRANCH=None TEST=Built and looked at resource allocation logs to confirm work around is no longer needed. Change-Id: I90b155cb5560ca3291f146c2f586456e5529f6b2 Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: https://chromium-review.googlesource.com/174652 Reviewed-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: http://review.coreboot.org/4902 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2014-02-24baytrail: get rid of global microcode_ptrAaron Durbin
A global microcode_ptr was added when doing the MP development work. However, this is unnecessary as the pattrs structure already contains the pointer. Use that instead. BUG=chrome-os-partner:22862 BRANCH=None TEST=Built and booted. Microcode still being loaded correctly. Change-Id: I0abba66fc7741699411d14bd3e1bb28cf1618028 Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: https://chromium-review.googlesource.com/174552 Reviewed-by: Shawn Nematbakhsh <shawnn@chromium.org> Reviewed-on: http://review.coreboot.org/4901 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2014-02-24baytrail: add microcode version 319Aaron Durbin
Update microcode version to 319. BUG=None BRANCH=None TEST=Built and booted. Noted 319 being used. Change-Id: I008f90a1c6b542d979e34da22e9f375224c0ffeb Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: https://chromium-review.googlesource.com/174551 Reviewed-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: http://review.coreboot.org/4900 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2014-02-24jetway/nf81-t56n-lf: Use proper category.Vladimir Serbinenko
"Mini-ITX" was a pure inventional name for category called "mini". Change-Id: I6450fd27c1a7679f252ce7f46f409b7dc459c50d Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com> Reviewed-on: http://review.coreboot.org/5286 Tested-by: build bot (Jenkins) Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com> Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
2014-02-24TI am335x: Apply Kconfig use conventionsKyösti Mälkki
Change-Id: Ic3c26fd7b1dd8a6731abc9a63b9ca17e084074b2 Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: http://review.coreboot.org/5291 Tested-by: build bot (Jenkins) Reviewed-by: Vladimir Serbinenko <phcoder@gmail.com>
2014-02-24CAR_GLOBAL: enforce compiler to check if _start != _endEdward O'Callaghan
There are some fun rules C compilers can use to optimize their code. One of them is the assumption that two symbols point to two different addresses. In this case this wasn't true, resulting in unintended code execution (and later, a crash) with a clang build. Change-Id: I1496b22e1d1869ed0610e321b6ec6a83252e9d8b Signed-off-by: Patrick Georgi <patrick@georgi-clan.de> Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com> Reviewed-on: http://review.coreboot.org/4719 Tested-by: build bot (Jenkins)
2014-02-22device: Do not show "framebuffer graphics resolution" with native init.Vladimir Serbinenko
No native init uses this. Real hardware ones use mode specified in EDID. Qemu one uses CONFIG_DRIVERS_EMULATION_QEMU_BOCHS_[XY]RES. Change-Id: I0845fec10b9811e2be44b5be30b9dc4f1c9719a6 Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com> Reviewed-on: http://review.coreboot.org/5281 Tested-by: build bot (Jenkins) Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
2014-02-21lib/edid: Don't set vbe_valid in decode_edid.Vladimir Serbinenko
Decoding EDID doesn't yet mean that gfx mode is used. Change-Id: Icedd36f26877754f34dd59233cce72271d7f0b19 Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com> Reviewed-on: http://review.coreboot.org/5269 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2014-02-20usbdebug: Unify console APIKyösti Mälkki
Struct dbgp_pipe would not be suitable for use with xHCI. Just use an index, it is easy to setup in Kconfig if our future debug setup has separate pipes for console output and debugging/traceings. Change-Id: Icbbd28f03113b208016f80217ab801d598d443a8 Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: http://review.coreboot.org/5227 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@google.com>
2014-02-20nehalem: Make SPD address map into parameter.Vladimir Serbinenko
It's mobo dependent. Change-Id: I7a9ba0fb7374a61178e9282acd8f10098435f1fd Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com> Reviewed-on: http://review.coreboot.org/5253 Tested-by: build bot (Jenkins) Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
2014-02-20nehalem/raminit: Fix typo of NUM_CHANNELS instead of NUM_SLOTS.Vladimir Serbinenko
Change-Id: I0fbfa8cb39881782bec3af5e43ff3c63dd2e4919 Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com> Reviewed-on: http://review.coreboot.org/5276 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2014-02-20ibexpeak/thermal: set temperature target in early init.Vladimir Serbinenko
Properly determine temperature target and set it in early init rather than hardcoding it in late init. Change-Id: Ie763f205890674a9dd1d9c5974caaccdd67cea14 Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com> Reviewed-on: http://review.coreboot.org/5264 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2014-02-20intel/model_2065x: Fix APICID generation.Vladimir Serbinenko
APIC IDs always step by 4 on 2065x independently of number of threads. Change-Id: I5abd4005c8ce1740bb0862d952af66236b609aa8 Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com> Reviewed-on: http://review.coreboot.org/5262 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2014-02-20SMM: Fixes for DEBUG_SMIKyösti Mälkki
Get the required UART includes directly. The ne2k part is old copy-paste leftover. Change-Id: Ifd9253abb5a50b515887459faf06b63f907eeda9 Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: http://review.coreboot.org/5258 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Aaron Durbin <adurbin@google.com>
2014-02-19ibexpeak/lpc: Fix PCIIDs.Vladimir Serbinenko
Add PCIID from Easynote LM85. Remove unrelated IDs inherited from BD82x6x. Change-Id: I03b6e0b2e08a4a6014aa1ef1f8d9a3a567f03ad9 Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com> Reviewed-on: http://review.coreboot.org/5263 Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Tested-by: build bot (Jenkins)
2014-02-19printk: support and use %hh prefixPatrick Georgi
clang complains otherwise. Change-Id: I2ac98d7147ecd3d7064f17f8c9d214d44baedf97 Signed-off-by: Patrick Georgi <patrick@georgi-clan.de> Reviewed-on: http://review.coreboot.org/4717 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
2014-02-19x86: only build disassembly with gccPatrick Georgi
The assembler options are specific to the gnu toolchain. Change-Id: I8424767ef186ef2d4c18bfbcae1f54e0da2e4f47 Signed-off-by: Patrick Georgi <patrick@georgi-clan.de> Reviewed-on: http://review.coreboot.org/4715 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
2014-02-19x86 bootblock: improve clang compatibilityPatrick Georgi
Its linker doesn't like "." arithmetics, so use .org, while its assembler doesn't like data32 prefixes. Change-Id: I3f5bbb350493d6510b8013df15d44c44c5db63c7 Signed-off-by: Patrick Georgi <patrick@georgi-clan.de> Reviewed-on: http://review.coreboot.org/4714 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
2014-02-18lynxpoint: Finalize chipset before playload if not CONFIG_CHROMEOSDuncan Laurie
The Chrome OS environment sends an SMI to finalize the chipset/board at the end of the "depthcharge" payload, but there is no facility to send this command if not using the full ChromeOS firmware stack. This commit adds a callback before booting the payload that will issue this SMI which will lock down the chipset and route USB devices to the XHCI controller. Change-Id: I2db9c44d61ebf8fa28a8a2b260a63d4aa4d75842 Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: http://review.coreboot.org/5181 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2014-02-17console: Add drivers/uartKyösti Mälkki
Also move UART related Kconfig options from top-level file. Change-Id: I4e407977cff6f6506f991600c98d6d264676d3f8 Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: http://review.coreboot.org/5230 Tested-by: build bot (Jenkins) Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
2014-02-17rambi: Set VBOOT_RAMSTAGE_INDEX to point to ramstage imageShawn Nematbakhsh
The ramstage image is the third image in the partition (after ECRW hash and depthcharge image). TEST=Manual. Boot rambi, verify that ramstage image is correctly found: "RW ramstage image at 0xffb1dc70, 0x0000f391 bytes" BUG=None. Change-Id: I628db3daf0b109106c51693960487a0c83b4e9f4 Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org> Reviewed-on: https://chromium-review.googlesource.com/174540 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: http://review.coreboot.org/4899 Tested-by: build bot (Jenkins) Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2014-02-17baytrail: add support to run reference code blobAaron Durbin
The reference code blob is needed to bootstrap certain pieces of hardware in bay trail. Provide the ability to run reference code by loading the reference code as an rmodule. Note that support for vboot verification and S3 resume is omitted from this commit. BUG=chrome-os-partner:22866 BRANCH=None TEST=Built and booted with refcode loading. Change-Id: I30334db441a57f4d87b4de6fca0a9a48e1c05c05 Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: https://chromium-review.googlesource.com/174426 Reviewed-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: http://review.coreboot.org/4898 Tested-by: build bot (Jenkins) Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
2014-02-17baytrail: add south cluster fixed resourcesAaron Durbin
The PCU (platform controller unit) contains the resources and IP blocks that used to reside in the south bridge. Bay Trail has since renamed it south cluster. There are quite a few fixed MMIO and I/O resources. If these aren't added the resource allocator will freely assign these addresses which causes conflicts and other subtle bugs. BUG=chrome-os-partner:23544 BUG=chrome-os-partner:23545 BRANCH=None TEST=Built and booted through depthcharge. Verified resource allocation not weird. And no more depthcharge crashes. Change-Id: I697fbda4538c03fded293bcb63a5823b1ed150ec Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: https://chromium-review.googlesource.com/174421 Reviewed-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: http://review.coreboot.org/4893 Tested-by: build bot (Jenkins) Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
2014-02-17lenovo/x201: Fix wrong declaration in devicetree.cbVladimir Serbinenko
Change-Id: I90c6ff14ab819368ccc874008a7fb1410a543984 Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com> Reviewed-on: http://review.coreboot.org/5255 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
2014-02-17baytrail: enable monotonic timerAaron Durbin
Enabling the monotonic timer allows for collecting boot stage times as well as each device initialization time. BUG=chrome-os-partner:23166 BRANCH=None TEST=Built and booted. Noted timings in console output. Change-Id: I5fdc703ea21710fd26de352f367c6fc0c767ab6a Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: https://chromium-review.googlesource.com/174422 Reviewed-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: http://review.coreboot.org/4894 Tested-by: build bot (Jenkins) Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
2014-02-17src/drivers/spi: introduce AMIC supportIdwer Vollering
Add support for the AMIC A25L032 flash chip. Change-Id: Ie8d441a923c6fbd18c16440b4571321652d934d5 Signed-off-by: Idwer Vollering <vidwer@gmail.com> Reviewed-on: http://review.coreboot.org/5252 Tested-by: build bot (Jenkins) Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
2014-02-17vortex86ex: Drop baudrate programming for 10 UARTsKyösti Mälkki
This is responsibility of end-user application. When coreboot does it, it is only for the purpose of debug console. Change-Id: Idbbf9528c60b9b819b7bea9dfe84078a3f055bc9 Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: http://review.coreboot.org/5251 Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com> Tested-by: build bot (Jenkins) Reviewed-by: Andrew Wu <arw@dmp.com.tw>
2014-02-17sandy/ivy: Fix mrc.cache file in CBFSKyösti Mälkki
The file was not recreated when configuration changed. One would hit this bug when turning CHROMEOS on/off. Also do not create mrc.cache with CHROMEOS at all. Change-Id: I5b0ecde66589396b24967ce289bf65e20bb08825 Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: http://review.coreboot.org/5211 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@google.com>
2014-02-17ibexpeak/azalia: Remove C4-register extended init.Vladimir Serbinenko
This sequence was derived from BD82X6X and on ibexpeak it inadvertently disables interrupts. In older kernels it wasn't a problem but in new kernel it makes codec probe fail. Change-Id: I40184ae8c4cfe758869af1a1565b88f0a238150e Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com> Reviewed-on: http://review.coreboot.org/5074 Tested-by: build bot (Jenkins) Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
2014-02-17ibexpeak/sata: Add PCI ID from Easynote LM.Vladimir Serbinenko
Change-Id: I979a40ad3692cd474920f3ee5c6b10c41f75bfdb Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com> Reviewed-on: http://review.coreboot.org/5256 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
2014-02-16baytrail: SMM supportAaron Durbin
Initialize SMM on all CPUs by relocating the SMM region and setting SMRR on all the cores. Additionally SMI is enabled in the south cluster. BUG=chrome-os-partner:22862 BRANCH=None TEST=Built and booted rambi. Tested with DEBUG_SMI and noted power button turns off board while in firmware. Change-Id: I92e3460572feeb67d4a3d4d26af5f0ecaf7d3dd5 Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: https://chromium-review.googlesource.com/173983 Reviewed-on: http://review.coreboot.org/4892 Tested-by: build bot (Jenkins) Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
2014-02-16haswell: backup the default SMM region on resumeAaron Durbin
Haswell CPUs need to use the default SMM region for relocating to the desired SMM location. Back up that memory on resume instead of reserving the default region. This makes the haswell support more forgiving to software which expects PC-compatible memory layouts. Change-Id: I9ae74f1f14fe07ba9a0027260d6e65faa6ea2aed Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: http://review.coreboot.org/5217 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@google.com>
2014-02-16x86: provide infrastructure to backup default SMM regionAaron Durbin
Certain CPUs require the default SMM region to be backed up on resume after a suspend. The reason is that in order to relocate the SMM region the default SMM region has to be used. As coreboot is unaware of how that memory is used it needs to be backed up. Therefore provide a common method for doing this. Change-Id: I65fe1317dc0b2203cb29118564fdba995770ffea Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: http://review.coreboot.org/5216 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@google.com>
2014-02-16intel/jarrell: Fix missing includeKyösti Mälkki
To unconditionally get cmos_read(). Change-Id: I0af0e85c8a1f42113bd32b51c4e29e86b3c28112 Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: http://review.coreboot.org/5228 Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com> Tested-by: build bot (Jenkins)
2014-02-16baytrail: bring up APsAaron Durbin
Bring up the APs using x86 MP infrastructure. BUG=chrome-os-partner:22862 BRANCH=None TEST=Built and booted rambi. Noted all cores are brought up. Change-Id: I9231eff5494444e8eb17ecdc5a0af72a2e5208b5 Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: https://chromium-review.googlesource.com/173704 Reviewed-on: http://review.coreboot.org/4889 Tested-by: build bot (Jenkins) Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
2014-02-16rambi: add BSP lapic deviceAaron Durbin
There's some baked in assumptions internal to coreboot that the BSP's cpu device exists in the device tree. Therefore provide one in the device tree. BUG=chrome-os-partner:22862 BRANCH=None TEST=Compiled and booted with other changes. Change-Id: I22ba10964760ee8efbc5bbd5d4ce65daf31b3839 Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: https://chromium-review.googlesource.com/173702 Reviewed-on: http://review.coreboot.org/4887 Tested-by: build bot (Jenkins) Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
2014-02-16baytrail: Modify GPIO pull-up specification methodShawn Nematbakhsh
Minor style changes to the way GPIO pull-ups are specified in board-specific GPIO maps. Intent is to allow calls to GPIO_FUNC macro from such maps. BUG=chrome-os-partner:22863 TEST=Manual. Build + boot on bayleybay. Change-Id: I80134b65d22d3ad8a049837dccc0985e321645da Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org> Reviewed-on: https://chromium-review.googlesource.com/173748 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Commit-Queue: David James <davidjames@chromium.org> Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: http://review.coreboot.org/4886 Tested-by: build bot (Jenkins) Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
2014-02-16rambi: disable internal pullups on ram_id[2:0]Aaron Durbin
The ram_id[2:0] signals have stuffing options for pull up/down with values of 10K. However, the default pulldown values for these pads are 20K. Therefore, one can't read a high value because of the high voltage threshold is 0.65 * Vref. Therefore the high signals are marginal at best. Fix this issue by disabling the internal pull for the pads connected to ram_id[2:0]. BUG=chrome-os-partner:23350 BRANCH=None TEST=Built and checked that ram_id[2:0] is properly read now. Change-Id: Ib414d5798b472574337d1b71b87a4cf92f40c762 Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: https://chromium-review.googlesource.com/173211 Reviewed-by: Shawn Nematbakhsh <shawnn@chromium.org> Reviewed-by: Bernie Thompson <bhthompson@chromium.org> Reviewed-on: http://review.coreboot.org/4885 Tested-by: build bot (Jenkins) Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
2014-02-16baytrail: correct MMC pci locationAaron Durbin
The original documentation was incorrect. Fix the pci device for the MMC port to reflect reality. MMC is at 00:17.0 with a device id of 0x0f50. BUG=None BRANCH=None TEST=Built. Change-Id: Ic18665b7dda5f386e72d1a5255e4e57d5b631eb0 Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: https://chromium-review.googlesource.com/172772 Reviewed-by: Shawn Nematbakhsh <shawnn@chromium.org> Reviewed-on: http://review.coreboot.org/4884 Tested-by: build bot (Jenkins) Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
2014-02-16baytrail: fix tsc rateAaron Durbin
Despite some references to a fixed bclk in some of the docs the bclk is variable per sku. Therefore, perform the calculation according to the BSEL_CR_OVERCLOCK_CONTROL msr which provides the bclk for the cpu cores in Bay Trail. BUG=chrome-os-partner:23166 BRANCH=None TEST=Built and booted B3. correctly says: clocks_per_usec: 2133 Change-Id: I55da45d42e7672fdb3b821c8aed7340a6f73dd08 Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: https://chromium-review.googlesource.com/172771 Reviewed-by: Shawn Nematbakhsh <shawnn@chromium.org> Reviewed-on: http://review.coreboot.org/4883 Tested-by: build bot (Jenkins) Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
2014-02-16usbdebug: Remove EHCI_DEBUG_OFFSETKyösti Mälkki
Read this variable from PCI configuration capabilities list instead. Change-Id: I0cfe981833873397c32cd3aa2af307f35f01784b Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: http://review.coreboot.org/5176 Tested-by: build bot (Jenkins) Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
2014-02-16Jetway NF81-T56N-LF [2/2]: actually implement mainboard support.Edward O'Callaghan
Step 2: change the Persimmon code to adapt it to the new board's hardware. The NF81-T56N-LF is a IPC form factor embedded board: - AMD Fusion G-T56N (1.65 GHz dual core) APU - 2x SO-DIMM sockets for DDR3 800-1066 SDRAM (Fixed at 1.5V) - VGA and LVDS (via Analogix ANX3110) - AMD A55E (Hudson-E1) southbridge - 6x USB 2.0/1.1 ports - 5x SATA3 6Gb/s, 1x mSATA socket - 6-Channel HD Audio (via VIA VT1705) - PCI and ISA (via ITE IT8888)?? - NEC uPD78F0532 microcontroller on I2C ("SEMA")?? - 2x RJ45 GbE (via Realtek RTL8111E x2) - Fintek F71869AD Super I/O - PS/2 KB/MS port - RS232 header (via Unisonic UTC 75232 RS232 driver/receiver) - GPIO header - CIR header - 1x MXIC MX25L1606E (SO8, soldered) 16 Mbit SPI flash (BIOS) Note: MX25L1606E is 16Mbit, 8bits in a byte, so 2MB. Jetway *lies* claiming the SPI flash is 16MB. They also use red pen over the chip so you wont see this deceit. Change-Id: I03ccc58bc782e800aeef0d19679ce060277b0c04 Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com> Reviewed-on: http://review.coreboot.org/4801 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2014-02-16Jetway NF81-T56N-LF [1/2]: create board by forking AMD PersimmonEdward O'Callaghan
Step 1: copy all files unmodified from Persimmon. This makes it much easier later to see how the two boards actually and deliberately differ when porting bugfixes from one to the other. Change-Id: I23e223049ed1c69e320e6b31efe4266bfeb97207 Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com> Reviewed-on: http://review.coreboot.org/4800 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2014-02-16lenovo/x60: Change to common EDID framework.Vladimir Serbinenko
Currently lenovo/x60 gfx init provides vbe_mode_info_valid in incompatible way. Use EDID framework as do other inits. Change-Id: I887abd5a09064f26f473a2bf9caa2eb33e269c07 Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com> Reviewed-on: http://review.coreboot.org/5238 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com> Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2014-02-16lenovo/x60: Fix EDID byte-swapping.Vladimir Serbinenko
Change-Id: I75305ff7c5a8ba6142ef460e813acc014d9992bb Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com> Reviewed-on: http://review.coreboot.org/5249 Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com> Tested-by: build bot (Jenkins)
2014-02-15console/uart8250*: Remove inclusion of mc146818rtc.hAlexandru Gagniuc
The RTC functionality provided by the include is specific to x86, but is not used in these files. Change-Id: I82d0dfdb6e8b67bc81291a7a5d63ced91e095772 Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com> Reviewed-on: http://review.coreboot.org/4586 Tested-by: build bot (Jenkins) Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
2014-02-15coreboot: infrastructure for different ramstage loadersAaron Durbin
There are 2 methods currently available in coreboot to load ramstage from romstage: cbfs and vboot. The vboot path had to be explicitly enabled and code needed to be added to each chipset to support both. Additionally, many of the paths were duplicated between the two. An additional complication is the presence of having a relocatable ramstage which creates another path with duplication. To rectify this situation provide a common API through the use of a callback to load the ramstage. The rest of the existing logic to handle all the various cases is put in a common place. Change-Id: I5268ce70686cc0d121161a775c3a86ea38a4d8ae Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: http://review.coreboot.org/5087 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
2014-02-15x86: provide stage_exit() like armAaron Durbin
The arm architectures have a stage_exit() function which takes a void * pointer as an entry point. Provide the same API for x86. This can make the booting paths less architecture-specific. Change-Id: I4ecfbf32f38f2e3817381b63e1f97e92654c5f97 Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: http://review.coreboot.org/5086 Tested-by: build bot (Jenkins) Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
2014-02-14google/rambi: Do not select CHROMEOS in KconfigAlexandru Gagniuc
CHROMEOS is the meant to be selected by the user. The correct variable for a mainboard to select is MAINBOARD_HAS_CHROMEOS. This will then default to a CHROMEOS build, but when the mainboard selects CHROMEOS, the user can no longer disable CHROMEOS. Change-Id: I78fb15a0a9fef733e2de064d6c09cf774b7bce78 Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com> Reviewed-on: http://review.coreboot.org/5218 Reviewed-by: Aaron Durbin <adurbin@google.com> Tested-by: build bot (Jenkins)
2014-02-13superio/fintek: Document Fintek F71869AD code.Edward O'Callaghan
Change-Id: I156077bf5571764d0e4bc044be80c8ab94556de4 Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com> Reviewed-on: http://review.coreboot.org/5178 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2014-02-13cpu/allwinner/a10: Add minimal ramstage driverAlexandru Gagniuc
Change-Id: I857755976b17b0e492c086162f395a77933eeed8 Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com> Reviewed-on: http://review.coreboot.org/4698 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2014-02-13baytrail: print dram configurationAaron Durbin
After running the MRC blob print out some information on the training: MRC version, number channels, DDR3 type, and DRAM frequency. Example output: MRC v0.90 2 channels of DDR3 @ 1066MHz Apparently there are two dunit IOSF ports -- 1 for each channel. However, certain registers really on live in channel 0. Thus, there was some changes to dunit support in the iosf area. BUG=chrome-os-partner:22875 BRANCH=None TEST=Built and booted bayleybay in different configs. Change-Id: Ib306432b55f9222b4eb3d14b2467bc0e7617e24f Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: https://chromium-review.googlesource.com/172770 Reviewed-by: Shawn Nematbakhsh <shawnn@chromium.org> Reviewed-on: http://review.coreboot.org/4882 Tested-by: build bot (Jenkins) Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
2014-02-13baytrail: allow downstream use of SSE instructionsAaron Durbin
If a payload is compiled to use SSE instructions it will fault with an undefined opcode because SSE instructions weren't enabled. Therefore enable SSE instructions at runtime. BUG=chrome-os-partner:22991 BRANCH=None TEST=Built and booted with SSE enabled payload. No exceptions seen. Change-Id: I919c1ad319c6ce8befec5b4b1fd8c6343d51ccc1 Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: https://chromium-review.googlesource.com/172642 Reviewed-by: Stefan Reinauer <reinauer@google.com> Reviewed-on: http://review.coreboot.org/4881 Tested-by: build bot (Jenkins) Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
2014-02-13baytrail: add vboot ramstage verificationAaron Durbin
Add suport for verifying the ramstage with vboot during romstage execution. Along with this support select CACHE_RELOCATED_RAMSTAGE_OUTSIDE_CBMEM to cache the relocated ramstage 1MiB below the top end of the TSEG region. BUG=chrome-os-partner:23249 BRANCH=None TEST=Built and booted with CONFIG_VBOOT_VERIFY_FIRMWARE=y selected. Signed-off-by: Aaron Durbin <adurbin@chromium.org> Change-Id: I355f62469bdcca62b0a4468100effab0342dc8fc Reviewed-on: https://chromium-review.googlesource.com/172712 Reviewed-by: Shawn Nematbakhsh <shawnn@chromium.org> Reviewed-on: http://review.coreboot.org/4880 Tested-by: build bot (Jenkins) Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
2014-02-13Eliminate some ASL warningsOskar Enoksson
The ASL compiler warned about "Control Method should be made Serialized (due to creation of named objects within)". This commit eliminates the warnings by changing those NonSerialized into Serialized. Change-Id: I639e769cf7a9428c34268e0c555a30c7dee1e04c Signed-off-by: Oskar Enoksson <enok@lysator.liu.se> Reviewed-on: http://review.coreboot.org/5189 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2014-02-12google boards: Do not hardcode location of spd.binAlexandru Gagniuc
spd.bin can reside anywhere in CBFS, and we only use CBFS APIs to access and read it. As such, there is no need to hardcode it, and it can collide with mrc.bin or mrc.cache on some boards. Do not use a specific position for spd.bin, but instead let cbfstool find the optimal placement. Change-Id: I496094d3c0de708813494095b7ac4be8addb4112 Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com> Reviewed-on: http://review.coreboot.org/5210 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Aaron Durbin <adurbin@google.com>
2014-02-12baytrail: gpio: add configs for PU/PD functional pinsShawn Nematbakhsh
Pull-ups and pull-downs can be active on functional pins. Add configs for these options so they can be specified on board GPIO maps. TEST=Manual on bayleybay. Verify that platform boots to payload load. BUG=chrome-os-partner:22863 Change-Id: Ie4f77d8ce812f086cc8fe5a6bfcac59669f56f92 Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org> Reviewed-on: https://chromium-review.googlesource.com/172766 Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: http://review.coreboot.org/5209 Tested-by: build bot (Jenkins) Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
2014-02-12falco: Add ACPI code to describe the I2C touchpad deviceDuncan Laurie
If the SerialIO devices are put into ACPI mode then it is possible to use ACPI to instantiate the touchpad in the kernel without needing to have a platform level driver to do the binding. This is the "new way" of describing on-board I2C devices and the upstream kernel is starting to add ACPI IDs to drivers so they can be used in this fashion. For the Cypress touchpad use a generic ACPI ID of "CYPA0000" to describe it. In order to support the proper scoping of the touchpad device under the appropriate I2C controller device the mainboard.asl file needs to be included after pch.asl so the I2C device exists. Change-Id: I81e053d27be478f3a19b6f9b13cd2b4fabcb88c0 Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: http://review.coreboot.org/5194 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2014-02-12lynxpoint: Do not put SerialIO devices into D3Hot in ACPI modeDuncan Laurie
Remove the bit of code that was putting the SerialIO devices into D3Hot state when they are switched from PCI to ACPI mode. Instead, add the appropriate ACPI Methods to allow the kernel to control the power state of the device. The problem seems to be that if the device is put in D3Hot state before it is switched from PCI to ACPI mode then it does not properly export its PCI configuration space and cannot be woken back up. Adding the ACPI Methods for _PS0/_PS3 allows the kernel to transition the device into D0 state only when it is necessary to communicate with the device, then put it back into D3Hot state. Change-Id: I2384ba10bf47750d1c1a35216169ddeee26881df Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: http://review.coreboot.org/5193 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2014-02-12PCI: Add capability list parser to romstageKyösti Mälkki
These are almost one-to-one copies from pci_device.c. However, devicetree has not been enumerated yet and we have no console. Change-Id: Ic80c781626521d03adde05bdb1916acce31290ea Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: http://review.coreboot.org/5196 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Aaron Durbin <adurbin@google.com>
2014-02-12PCI: Drop includes under cpuKyösti Mälkki
The files affected do not make any PCI configuration calls. If they did, the more correct includes would be pci_ops.h, pci_defs.h and pci_ids.h. Change-Id: I3e7f009371be6ea50318eaabf0c15500cb3f1210 Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: http://review.coreboot.org/5200 Reviewed-by: Aaron Durbin <adurbin@google.com> Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com> Tested-by: build bot (Jenkins)
2014-02-12PCI: Guard pci.h with CONFIG_PCIKyösti Mälkki
Adding PCI functions for romstage in pci.h breaks ARMv7 build without this. Also fix two related includes to use pci_def.h instead. Change-Id: I5291eaf6ddf5a584f50af29cf791d2ca4d9caa71 Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: http://review.coreboot.org/5199 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Aaron Durbin <adurbin@google.com>
2014-02-12usbdebug: Split to USB host/deviceKyösti Mälkki
Top-level interface to console over USB mut not require low-level details of ECHI debug port internals. Change-Id: If3ca3b1f479e3f20976cd4abd8f5e682a58d5650 Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: http://review.coreboot.org/5197 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@google.com>
2014-02-12winbond/w83627hf/acpi: Fix some ASL warningsOskar Enoksson
There were ASL compiler warnings about "Size mismatch". This commit eliminates the warnings by changing the ASL declarations of those fields. Change-Id: If851ed4892ef6c96acbff861abd7001ab67d9d66 Signed-off-by: Oskar Enoksson <enok@lysator.liu.se> Reviewed-on: http://review.coreboot.org/5190 Reviewed-by: Ronald G. Minnich <rminnich@gmail.com> Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2014-02-12hp/dl145_g1: Add missing copyright notesOskar Enoksson
Missing copyright notes added. Change-Id: I55b320a169b1125017c63b7a2384078465e7ce6e Signed-off-by: Oskar Enoksson <enok@lysator.liu.se> Reviewed-on: http://review.coreboot.org/5188 Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com> Tested-by: build bot (Jenkins)
2014-02-12hp/dl145_g1: Fix some commented out codeOskar Enoksson
Some out-commented code contained variables which changed name. This commit fixes the "problem". Change-Id: I8d9168c9f4b2cb6810b3e4dfeff2155f3c08357d Signed-off-by: Oskar Enoksson <enok@lysator.liu.se> Reviewed-on: http://review.coreboot.org/5187 Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com> Tested-by: build bot (Jenkins)
2014-02-11hp/dl145_g1: Add HAVE_HARD_RESETOskar Enoksson
This platform has a hard reset button Change-Id: Ic4d2f9382b6770654eea8842a37ad38cf12de459 Signed-off-by: Oskar Enoksson <enok@lysator.liu.se> Reviewed-on: http://review.coreboot.org/5097 Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com> Tested-by: build bot (Jenkins)
2014-02-11hp/dl145_g1: Adding FID/VID and Powernow ACPIOskar Enoksson
Add cool-n-quiet functionality which allows the OS to dynamic alter CPU voltage and frequency change in order to save power e.g. when the CPU load is low. Change-Id: I4c895a56bcf571d4276af192aeef87d120143063 Signed-off-by: Oskar Enoksson <enok@lysator.liu.se> Reviewed-on: http://review.coreboot.org/5186 Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com> Reviewed-by: David Hendricks <dhendrix@chromium.org> Tested-by: build bot (Jenkins)
2014-02-11amd/cimx: fix sb(8|9)00 NULL type redefineAaron Durbin
It is inappropriate for chipset code to be redefining types -- especially NULL to a non-pointer type. There's only one non-straight forward change. A condition being checked was '!ptr_type == NULL' (0 as int). That check is actually 'ptr_type != NULL'. Change-Id: Iab5733e5a573baba6fec94e0c955ba4fad72c836 Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: http://review.coreboot.org/5088 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
2014-02-11baytrail: add reset supportAaron Durbin
Bay Trail has the following types of resets it supports: - Soft reset (INIT# to cpu) - write 0x1 to I/O 0x92 - Soft reset (INIT# to cpu)- write 0x4 to I/0 0xcf9 - Cold reset (S0->S5->S0) - write 0xe to I/0 0xcf9 - Warm reset (PMC_PLTRST# assertion) - write 0x6 to I/O 0xcf9 - Global reset (S0->S5->S0 with TXE reset) - write 0x6 or 0xe to 0xcf9 but with ETR[20] set. While these are documented this support currently provides support for 2nd soft reset as well as cold and warm reset. BUG=chrome-os-partner:23249 BRANCH=None TEST=Built and booted. Change-Id: I9746e7c8aed0ffc29e7afa137798e38c5da9c888 Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: https://chromium-review.googlesource.com/172710 Reviewed-by: Shawn Nematbakhsh <shawnn@chromium.org> Reviewed-on: http://review.coreboot.org/4878 Tested-by: build bot (Jenkins) Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
2014-02-11rambi: Add platform GPIO configuration tablesShawn Nematbakhsh
Configure GPIOs according to function on board. TEST=compile only. BUG=chrome-os-partner:22863 Change-Id: Ic38eeb64149606f2d7a19cc7a0144cc7e24807b8 Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org> Reviewed-on: https://chromium-review.googlesource.com/172657 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: http://review.coreboot.org/4875 Tested-by: build bot (Jenkins) Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
2014-02-11rambi: Add ncore GPIO config tablesShawn Nematbakhsh
gpncore config tables were previously missing -- add them. Also, make the baytrail GPIO/PAD LUTs easier to read. TEST=Manual. Build + boot on bayleybay. BUG=chrome-os-partner:22865 Change-Id: I49a1b23c7ad4fb5f4c86618e8c78ea9a1a42f79d Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org> Reviewed-on: https://chromium-review.googlesource.com/172510 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: http://review.coreboot.org/4874 Tested-by: build bot (Jenkins) Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
2014-02-11rambi: add per-sku SPD supportAaron Durbin
There are currently 4 SKUs: 0b000 - 4GiB total - 2 x 2GiB Micron MT41K256M16HA-125:E 1600MHz 0b001 - 4GiB total - 2 x 2GiB Hynix H5TC4G63AFR-PBA 1600MHz 0b010 - 2GiB total - 2 x 1GiB Micron MT41K128M16JT-125:K 1600MHz 0b011 - 2GiB total - 2 x 1GiB Hynix H5TC2G63FFR-PBA 1600MHz Add each of the 4 spds to the build, and use the proper parameters to MRC to use the in-memory SPD information. BUG=chrome-os-partner:22865 BRANCH=None TEST=Built. Noted 1024 bytes of SPD content. Change-Id: Ife96650f9b0032b6bd0d1bdd63b8970e29868365 Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: https://chromium-review.googlesource.com/172280 Reviewed-on: http://review.coreboot.org/4872 Tested-by: build bot (Jenkins) Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
2014-02-11baytrail: move early init to before mainboardAaron Durbin
It's helpful to have a lot of the early init happen before the handoff to mainboard. One example of this need is having the BARs programmed so that the mainboard can read board-specific gpios. BUG=chrome-os-partner:22865 BRANCH=None TEST=Built. Booted and saw console outout in bayleybay mainboard. Signed-off-by; Aaron Durbin <adurbin@chromium.org> Change-Id: I030d7b4f9061ad7501049e8e204ea12255061fbe Reviewed-on: https://chromium-review.googlesource.com/172290 Tested-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Duncan Laurie <dlaurie@chromium.org> Commit-Queue: Aaron Durbin <adurbin@chromium.org> Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: http://review.coreboot.org/4871 Tested-by: build bot (Jenkins) Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
2014-02-11baytrail: Add functions to peek at GPIO input valuesShawn Nematbakhsh
- Add functions to peek at GPIO input pad values (need to be used from romstage for board ram_id GPIOs) - Modify UART GPIOs to use existing fn-assignment function TEST=Manual. Add debug print and verify that GPIO functions return input values. Also, verify UART still functions in romstage. BUG=chrome-os-partner:22865 Change-Id: Ib2e57631c127a592cfa20ab6e2184822424e9d77 Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org> Reviewed-on: https://chromium-review.googlesource.com/172189 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: http://review.coreboot.org/4870 Tested-by: build bot (Jenkins) Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
2014-02-11baytrail: set max frequency early in romstageAaron Durbin
Set the BSP to operate at max frequency early in romstage. The call to punit_init() is when the frequency actually ramps as that makes the punit actually start working. BUG=chrome-os-partner:22857 BRANCH=None TEST=Built and booted. Noted operating frequency status is max. Change-Id: Icfd9e5c7682aa21fc740bd687607ca6a66597d5e Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: https://chromium-review.googlesource.com/172131 Reviewed-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: http://review.coreboot.org/4869 Tested-by: build bot (Jenkins) Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
2014-02-11baytrail: adjust cache policy during romstageAaron Durbin
The caching policy for romstage was previously using a 32KiB of cache-as-ram for both the MRC wrapper and the romstage stack/data. It also used a 32KiB code cache region. The BWG's limitations for the code and data region before memory is up was wrong. It consists of a 16-way set associative 1MiB cache. As long as enough addresses are not read there isn't a risk of evicting the data/stack. Now create a 64KiB cache-as-ram region split evenly between romstage and the MRC wrapper. Additionally cache the memory just below 4GiB in CBFS size. This will cover any code and read-only data needed. BUG=chrome-os-partner:22858 BRANCH=None TEST=Built and booted quickly with corresponding changes to MRC warpper. CQ-DEPEND=CL:*146175 Change-Id: I021cecb886a9c0622005edc389136d22905d4520 Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: https://chromium-review.googlesource.com/172150 Reviewed-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: http://review.coreboot.org/4868 Tested-by: build bot (Jenkins) Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
2014-02-11baytrail: add punit access functionsAaron Durbin
Like the bunit and dunit, add the punit accessor functions. BUG=chrome-os-partner:23085 BRANCH=None TEST=Built. Change-Id: Ifd7184dfca8c0491c107bc1c562ea1ded444e372 Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: https://chromium-review.googlesource.com/171931 Reviewed-on: http://review.coreboot.org/4867 Tested-by: build bot (Jenkins) Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com> Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
2014-02-11baytrail: make default GPIO configs closer to power-on defaultsShawn Nematbakhsh
- Set config0 defaults for hysteresis disable, pad bypass, etc. - Set config1 power-on defaults. - Set pad_val for input as default. BUG=chrome-os-partner:22863 TEST=Manual. Enable GPIO_DEBUG and verify pad registers are set according to expectation. Also verify bayleybay still boots to payload loading. Change-Id: I0f1c9e4d4f39c5c56d7e14a82eb4825612e19420 Reviewed-on: https://chromium-review.googlesource.com/171903 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Commit-Queue: Shawn Nematbakhsh <shawnn@chromium.org> Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org> Tested-by: Shawn Nematbakhsh <shawnn@chromium.org> Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: http://review.coreboot.org/4866 Tested-by: build bot (Jenkins) Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
2014-02-11SMP: Add arch-agnostic boot_cpu()Kyösti Mälkki
We should not have x86 specific includes in lib/. Change-Id: I18fa9c8017d65c166ffd465038d71f35b30d6f3d Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: http://review.coreboot.org/5156 Tested-by: build bot (Jenkins) Reviewed-by: David Hendricks <dhendrix@chromium.org> Reviewed-by: Aaron Durbin <adurbin@google.com>
2014-02-11Move hexdump32() to lib/hexdump.Kyösti Mälkki
Needs printk and is not a console core function. Change-Id: Id90a363eca133af4469663c1e8b504baa70471e0 Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: http://review.coreboot.org/5155 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
2014-02-11Kconfig: Move vendorcode menu up from the bottom to above Chipset menuPeter Stuge
Change-Id: Ic97a497a634533f44d94df297ca6e35d94c34565 Signed-off-by: Peter Stuge <peter@stuge.se> Reviewed-on: http://review.coreboot.org/5160 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com> Reviewed-by: Aaron Durbin <adurbin@google.com>
2014-02-11hp/dl145_g1: Adding ACPI supportOskar Enoksson
Basic ACPI support for this old platform. Created by copying and tweaking similar motherboard ACPI implementations in coreboot. Works reasonably well under Linux, providing HPET-timers and more under linux (tested under OpenSUSE 12.2 kernel 3.4.63-2.44). Not tested under Windows. Change-Id: I69431be962a0d272db398ecf4ac9f0249de8ebab Signed-off-by: Oskar Enoksson <enok@lysator.liu.se> Reviewed-on: http://review.coreboot.org/5185 Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com> Tested-by: build bot (Jenkins) Reviewed-by: David Hendricks <dhendrix@chromium.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2014-02-10usbdebug: Split PCI EHCI partKyösti Mälkki
There are EHCI compatible host controllers on ARM without PCI bus architecture. Currently we have not come across one with the debug capability though. Change-Id: I8775c9814f6fdf8754f97265118a7186369d721d Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: http://review.coreboot.org/5175 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@google.com>
2014-02-10usbdebug: Fix data toggle on receiveKyösti Mälkki
USB device end toggles data PID when we ACK'd the zero-length data packet. As USB host we need to toggle data PID too or the next data received would get discarded. Change-Id: I3203bc874c7ded9244c7548a666d7041a0fbb379 Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: http://review.coreboot.org/4775 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@google.com>
2014-02-10usbdebug: Remove duplicate port claimKyösti Mälkki
This claim is useless when done before EHCI controller reset. Code in usbdebug_init_() already sets this properly after reset, see use of DBGP_OWNER. Change-Id: Ic17493fe4edbbbed6ebcbef35a264fbf188f1fba Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: http://review.coreboot.org/4709 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@google.com>
2014-02-10usbdebug: Improve receive speedKyösti Mälkki
Read from USB endpoint_in 8 bytes at a time, the maximum what EHCI debug port capability has to offer. Change-Id: I3d012d758a24b24f894e587b301f620933331407 Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: http://review.coreboot.org/4700 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@google.com>
2014-02-09device_util: Make device in dev_find_slot_pnp u16.Vladimir Serbinenko
LDN is 8-bit but coreboot squeezes unrelated info: VLDN in this field. Increase to 16-bit to handle this. Change-Id: I97af1b32dcfaed84980fa3aa4c317dfab6fad6d8 Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com> Reviewed-on: http://review.coreboot.org/5165 Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com> Tested-by: build bot (Jenkins)
2014-02-09mtrr: only add prefetchable resources as WRCOMB for VGA devicesAaron Durbin
Be more conservative and only add VGA devices' prefetchable resources as write-combining in the address space. Previously all prefetchable memory was added as a write-combining memory type. Some hardware incorrectly advertises its BAR as prefetchable when it shouldn't be. A new memranges_add_resources_filter() function is added to provide additional filtering on device and resource. Change-Id: I3fc55b90d8c5b694c5aa9e2f34db1b4ef845ce10 Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: http://review.coreboot.org/5169 Reviewed-by: Vladimir Serbinenko <phcoder@gmail.com> Tested-by: build bot (Jenkins)
2014-02-07device_util: Add dev_find_slot_pnp.Vladimir Serbinenko
Change-Id: I5223c54c8ddbc60a176e4d718730e99decc772a3 Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com> Reviewed-on: http://review.coreboot.org/5112 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
generated by cgit v1.2.3 (git 2.25.1) at 2024-12-17 01:01:41 +0000