Age | Commit message (Collapse) | Author |
|
SMBHST_STAT_NOERROR was a redefinition of SMBHST_STAT_INTERRUPT that was
used in smbus_wait_until_done. Remove the misleading bit definition that
also didn't correspond with the register definitions and replace it with
the definition of the actual bit that gets checked. Also add a comment
that the code actually checks the IRQ status flag to see if the last
command is already completed.
Change-Id: I1a58fe0d58d3887dd2e83320e977a57e271685b3
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48219
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
Change-Id: I6df9323dc4e7ca99fd5368f0262e850c0aca5c54
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48218
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
The patch also rewrites the bit definition using shifts to make them
easier to read.
The older non-SoC chips can probably also use the new header file, but
for this patch the scope is limited to soc/amd, since the older non-SoC
chips don't use the SMBUS controller code in soc/amd/common.
TEST=Timeless build for amd/mandolin and amd/gardenia doesn't change.
Change-Id: Ifd5e7e64a41f1cb20cdc4d6ad1e675d7f2de352b
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48188
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
The code on Stoneyridge didn't set the FCH_AOAC_TARGET_DEVICE_STATE bits
to FCH_AOAC_D0_INITIALIZED like the code for Picasso does, but that is
the default value after reset for those bits on both platforms.
Change-Id: I7cae23257ae54da73b713fe88aca5edfa4656754
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48183
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
The register locations and bit definitions are the same for Stoneyridge
and Picasso. Since not all devices are present on all SoCs, keep those
numbers in the SoC-specific code.
Change-Id: Ib882927e399031c376738e5a35793b3d7654b9cf
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48182
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
The ability to set up a custom memory profile is useful if you don't
like the XMP memory profiles (if they exist) of your RAM sticks, or
want to try some overclocking. Read SPD data will be overriden by your
custom values. Tested on Crucial BLT8G3D1869DT1TX0 (1866MHz 9-9-9-27).
Signed-off-by: Mike Banon <mikebdp2@gmail.com>
Change-Id: I1238ff00ef0efd11ea807794827476c30ac98065
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40489
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
|
|
Add XMP memory profiles support that has been tested on f15tn (A88XM-E)
and f16kb (AM1I-A) with two Crucial BLT8G3D1869DT1TX0, XMP 1 profile.
Added using the datasheets from https://github.com/mikebdp2/ddr3spd :
JEDEC_DDR3_SPD_4_01_02_11R24.pdf and Intel_XMP_Spec_Rev1.1.pdf
Signed-off-by: Mike Banon <mikebdp2@gmail.com>
Change-Id: I584416e3376afdf377a11783e55c5e9ff41e6b0d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40488
Reviewed-by: Lance Zhao
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I37382ab06a8f1760e955d1ec76a6a00958b05999
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48177
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
On x86_64 the cannary is 8 bytes in size, so write the additional
4 bytes to make SMM handler happy.
Tested on Intel Skylake in long mode. No longer dies in SMM.
Change-Id: Id805c65717ec22f413803c21928d070602522b2c
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48215
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The previous code was crashing when jumping back to ramstage, now it
works. The GDT is now using the same values as the other ones in
coreboot.
Change-Id: Id00467d9d8a4138ddea73adbda4b39f12def583f
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48214
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add the fw_config entries for the newly added boot device fields.
These are added as separate fields since a board may have more
than one selected.
BUG=b:173129299
TEST=abuild google/volteer
Change-Id: I2af9ffcf0b90d4f4b7f2f31613ee110d8f350454
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48160
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
The initial commit only focused on GL9755S and RTS5261, but there
were recently other cards added to the fw_config and those also
need to be added to the probe lists.
BUG=b:173207454
TEST=abuild google/volteer
Change-Id: Ic27074a016ffbd4c4dd86104a6d85437357c4b82
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48159
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sukumar Ghorai <sukumar.ghorai@intel.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Now that the initial version of the Picasso FSP binaries have finally
landed, we can set the default paths to point to them now.
Change-Id: Ib2241cc90c7113e0c3de4409e08b9ae1f4c2f51e
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42472
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Jason Glenesk <jason.glenesk@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I928b4528fa5b4c378a2e8ff7bb88547da1413df2
Signed-off-by: Meera Ravindranath <meera.ravindranath@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48213
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: V Sowmya <v.sowmya@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The FSP-M/S/T related headers added are generated as per FSP v2341.
Signed-off-by: Tan, Lean Sheng <lean.sheng.tan@intel.com>
Change-Id: I98f738402490b47efa1a346f81db47857e384e13
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47803
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
Update Kconfig:
1. use FSP2.1 instead of 2.2
2. remove HECI_DISABLE_USING_SMM config
3. update CAR related stack & ram size
4. update FSP heap size
5. set IED region size = 0 as it is not used
6. update SMM TSEG size
7. update RP & I2C max device #s
8. update UART base address
Signed-off-by: Tan, Lean Sheng <lean.sheng.tan@intel.com>
Change-Id: I6a44d357d71be706f402a6b2a4f2d4e7c0eeb4a9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45078
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The extracted VBIOS Option ROM ships the same ID for several
generations, not matching the ID on the hardware resulting in a
mismatch, and coreboot does not run the Option ROM.
PCI ROM image, vendor ID 8086, device ID 0406,
ID mismatch: vendor ID 8086, device ID 5916
Add the appropriate mappings.
TEST=coreboot runs the ROM on the TUXEDO Book BU1406.
Change-Id: Ia167d91627a7ff1b329ea75f150b3ce95c0acccb
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43853
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Default VBT supports only integrated Display port. Drawman supports a
HDMI port and hence support a separate VBT for Drawman.
BUG=b:161190931
BRANCH=dedede
TEST=Build and boot to OS in Drawlat and Drawman.
Cq-Depend: TBD
Change-Id: I8895cc67d87428eddb31328f1e3a90c346b54533
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48192
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
|
|
Add daughter-board ports bit field and mask in devicetree.
BUG=b:161190931
BRANCH=dedede
TEST=Build and boot to OS in drawlat & drawman.
Change-Id: Ibbd86fc8c3e44a7d1703b8ce75c48881226545c9
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48191
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
|
|
The headers added are generated as per FSP v2385_04.
Previous FSP version was 2385_02.
Changes Include:
- add FastPkgCRampDisable, SlowSlewRate, PreWake, RampUp and
RampDown UPDs in Fsps.h
BUG=b:174330941
BRANCH=dedede
TEST=Build and boot JSLRVP
Cq-Depend: chrome-internal:3438485
Change-Id: I477af05c34f767a43990670a711992641eaf6000
Signed-off-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47862
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add memory table to "mem_parts_used.txt", and command to generate files:
go build gen_part_id.go
./gen_part_id ../../../src/mainboard/google/zork/spd
../../../src/mainboard/google/zork/variants/shuboz/spd/
../../../src/mainboard/google/zork/variants/shuboz/spd/mem_parts_used.txt
Shuboz memory table as follow:
value Vendor Part number
0x00 MICRON MT40A512M16TB-062E:J
0x01 HYNIX H5AN8G6NCJR-XNC
0x02 MICRON MT40A1G16KD-062E:E
0x03 SAMSUNG K4AAG165WA-BCWE
BUG=b:174528384
BRANCH=zork
TEST=emerge-zork coreboot
Signed-off-by: Kane Chen <kane_chen@pegatron.corp-partner.google.com>
Change-Id: I5f5f875daab58343f1cc8a9327ea128ba5e1f050
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47902
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Rob Barnes <robbarnes@google.com>
|
|
Config HID-I2C device to level trigger.
As per HID over I2C Protocol Specification[1] Version 1.00 Section 7.4,
the interrupt line used by the device is required to be level triggered.
Hence, this change updates the configuration of the HID over I2C devices
to be level triggered.
References:
[1] http://download.microsoft.com/download/7/d/d/7dd44bb7-2a7a-4505-ac1c-7227d3d96d5b/hid-over-i2c-protocol-spec-v1-0.docx
BUG=b:171546871
TEST=emerge-dedede coreboot
Change-Id: If8be25f591715765a99920b79482c862b1cc7079
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48193
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Check that stages running in CAR have their start and end in CAR.
Change-Id: I292aacce564c23d9ae21aa46c5e2f8784fa6a609
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36623
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Add NULL pointer check in acpigen_emit_namestring
to avoid segmentation fault.
Change-Id: I3d01d28e74f202278b5a5a96d2edd45c66f10883
Signed-off-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48148
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
In commit 09d50671e6b43c23853a91ff4d6fb26c1e7e17a1 the AOAC code was
reworked for Picasso and this patch ports this back to Stoneyridge to
facilitate factoring out the functionality into common code.
Change-Id: I836b91dc647987d064170fff7c8ca6ef2ee49211
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48181
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
The numbers in the array are unsigned, so use an unsigned type there.
Change-Id: I9a85594de0e4c53db965ab84239f19eb46432348
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48180
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
The power_off_aoac_device function clears the FCH_AOAC_PWR_ON_DEV bit,
so the comment should be that it powers off the devices.
Change-Id: Ia5e5d80b1977c3f53fcd9cf6d48bdb59045dfc3c
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48155
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
Change-Id: Ie44ded11a6a9ddd2a1163d2f57dad6935e1ea167
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48172
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Change-Id: Ieac4a4924ff4684b2a419471cd54e3d3b1f5bbe6
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48171
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Doesn't affect x86_32.
Tested on Intel Skylake. Boots into bootblock and console is working.
Change-Id: I1b36ca8816dab9d30754aadd230c136978e3b344
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48170
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I5fb6594ff83904df02083bcbea14b2d0b89cd9dd
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48169
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Change-Id: Id63b9b372bf23e80e25b7dbef09d1b8bfa9be069
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48168
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Change-Id: Ibc8dc1cf33f594284edb82d4730967e077739c3c
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48167
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Change-Id: Ia713e7dbe8c75b764f7a4ef1a029e64fb2d321fb
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48166
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Allows to compile the file under x86_64 without errors.
The caller has to make sure to call the functions while in protected
mode, which is usually the case in early bootblock.
Change-Id: Ic6601e2af57e0acc6474fc3a4297e3d2281decd6
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48165
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Allows to compile the file under x86_64 without errors.
The caller has to make sure to call the functions while in protected
mode, which is usually the case in early bootblock.
Change-Id: Ic6d98febb357226183c293c11ba7961f27fac40c
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48164
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Current flash layout doesn't support the fsp debug builds since
the FW_MAIN_A/B doesn't have enough space to hold the fsp debug
binaries along with ME RW binaries.
This patch reduces the SI_ALL size to 3.5MiB and increase the
SI_BIOS to 12.5MiB to include both ME RW and FSP debug binaries.
BRANCH=dedede
TEST=Build and Boot jslrvp with fsp debug enabled coreboot.
Cq-Depend: chrome-internal:3425366
Change-Id: I6f6354b0c80791f626c09dabafe33eefccedb9c2
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48154
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
AGESA checks to make sure that the firmware version reading the MRC
cache is the same version that wrote it, so it doesn't need to be
erased during a firmware update.
BUG=b:173724014
TEST=Flash firmware to DUT, update firmware, check RW_MRC_CACHE was
not erased
BRANCH=Zork
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: Ice3d1d467c25366b7ef678cd6481d043f62644ca
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47776
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Enter long mode on secondary APs.
Tested on Lenovo T410 with additional x86_64 patches.
Tested on HP Z220 with additional x86_64 patches.
Still boots on x86_32.
Change-Id: I53eae082123d1a12cfa97ead1d87d84db4a334c0
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45187
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Use the system library for header files instead of relative filesystem
paths.
Built with BUILD_TIMELESS=1, coreboot.rom remains the same.
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Change-Id: I0b356d0188f104d7c49571ce5c8fe65e79589123
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48141
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
|
|
Built with BUILD_TIMELESS=1, coreboot.rom remains the same.
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Change-Id: Id78c478a1252099cd1aa42c62efd406e7e1c5ef8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48140
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
|
|
Update port connector information for Delta Lake.
Tested=Execute "dmidecode -t 8" to check all the information of
SMBIOS type 8 is correct.
Signed-off-by: Tim Chu <Tim.Chu@quantatw.com>
Change-Id: I880bb9a5a41077172423f78b56c19aadd93e001f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47893
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jonathan Zhang <jonzhang@fb.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Inject TAB to make OperationRegion closing brace align with
opening brace.
Change-Id: Idb9f23cf6a2c249fb1fd02f4a2ac314d4f7e180b
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48149
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
As per latest schematics GPP_A15 is not used for EC_SYNC_IRQ
hence remove the unused GPIO.
Wrong GPIO configuration is causing platform reboot issue on
ADLRVP with Chrome SKU.
Change-Id: I704cd722683258c80197d8872d3bdaafb7c923dc
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48131
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: V Sowmya <v.sowmya@intel.com>
|
|
1. Add 2 ports and 2 endpoints
2. Add support for OVTI5675
WFC Cam is on I2C5 and UFC is on I2C1
BUG=None
BRANCH=None
TEST=Build and Boot adlrvp board and able to capture image
using camera.
Signed-off-by: Varshit Pandya <varshit.b.pandya@intel.com>
Change-Id: I6d2a4fdca99354d1b6977233c70ccd950c99d8a2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47497
Reviewed-by: V Sowmya <v.sowmya@intel.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Configure RST and PWR_EN signals for both WFC and UFC
Signed-off-by: Varshit Pandya <varshit.b.pandya@intel.com>
Change-Id: Ie416da373756b1c73472b8572f87930965a3d6ec
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47496
Reviewed-by: V Sowmya <v.sowmya@intel.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Configure I2C related GPIO as per ADL-P schematics.
This is based on Revision 0.974 of schematics.
Signed-off-by: Varshit Pandya <varshit.b.pandya@intel.com>
Change-Id: I76e1207cb31bed10b6e9fbeb2456b6feec42f97e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47495
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: V Sowmya <v.sowmya@intel.com>
|
|
List of changes:
1. Enable Root Port 8 aka 0:0x1c:7
2. Assign free running clock for RP8
3. Apply W/A to get card detected on x1 slot
- Drive OEB 7:GPP_A7 and OEB 6:GPP_E5 low
TEST=Able to detect PCIe SD card over x1 slot
localhost ~ # dmesg | grep mmc
[ 3.643755] mmc0: SDHCI controller on PCI [0000:02:00.0] using ADMA
[ 3.825201] mmc0: new ultra high speed DDR50 SDHC card at address 17f8
[ 3.835452] mmcblk0: mmc0:17f8 SE16G 14.4 GiB
[ 3.849158] mmcblk0: p1
Change-Id: Ibea37b8de4dd020ff0108ec90ea6f8bcfaa4fb17
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48080
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: V Sowmya <v.sowmya@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
List of changes in SPD:
1. SPD Revision (of JEDEC spec)
2. SDRAM Maximum Cycle Time (tCKAVGmax) (MTB)
3. MSB -> CAS Latencies Supported, First Byte
4. CAS Latencies Supported, Second Byte
5. CAS Latencies Supported, Third Byte
6. LSB -> CAS Latencies Supported, Fourth Byte
7. Minimum CAS Latency Time (tAAmin)
8. Fine Offset for SDRAM Maximum Cycle Time (tCKAVGmax)
9. Fine Offset for SDRAM Minimum Cycle Time (tCKAVGmin)
10.Cyclical Redundancy Code (0- 125 byte)
TEST=Able to build and boot with updated SPD.
Change-Id: Iae7f2693e87bffb2dfa20bd07b22f4a4768c56cb
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48079
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: V Sowmya <v.sowmya@intel.com>
|
|
This patch adds LPDDR5 memory configuration parameters to FSP.
TEST=Able to pass FSP-M MRC training on LPDDR5 RVP.
Signed-off-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Change-Id: I787bf97dd6c244bd3b0662e5bd061a2da80baa90
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46899
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: V Sowmya <v.sowmya@intel.com>
|
|
List of changes:
1. Initialize dq_map array in a single line
2. Make dqs_map array also in a single line
TEST=Able to build and boot ADLRVP LP4 SKU.
Change-Id: I64f2b38492934c8ede301f4b252c8700060ed4ac
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48077
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: V Sowmya <v.sowmya@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Get rid of variant_gpio_table() and configure GPIOs in gpio.c instead
of passing data around.
Change-Id: Ib158d6bdbcbceb3c1dc4f47fc7c3e098b9c7e5c4
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47974
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Use include folder for header files allowing proper includes.
Change-Id: I80066fb925b918d040062397e633c5d499a50dbe
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47973
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Hook up the mainboard_ops driver and configure the GPIOs using .init,
since mainboard_silicon_init_params() is meant for the configuration of
the FSP, not the GPIOs.
Change-Id: I6ab8d258c6f81c90d835cb8d07c6387d3de76d85
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47850
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
mainboard_silicon_init_params() is *not* meant for configuring GPIOs. It
should only be used to configure FSP options, which can not be
configured elsewhere.
Change-Id: Ia92d0d173af9c67600e93b473480967304772998
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48008
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
PICASSO_LPC_IOMUX was only used in the amd/mandolin board, but not in
the corresponding SoC code, so remove it from the SoC's Kconfig and
reanme it in the mainboard's Kconfig to MANDOLIN_LPC.
Change-Id: I261e093d6c56be6073a816b79c60d3a0457616f8
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47891
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
The corresponding functionality in the SoC's Makefile.inc was removed in
commit ef3395d990bbf1118a8d4e367a986bdbc92b1820
Change-Id: Iba84d9deb155ce314b3a3588781752b83a21486b
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47890
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
There's no need to have the bootblock in its own sub-directory, so move
it to each SoC's main directory to avoid clutter. This makes soc/amd
more consistent with the coreboot code base in src/northbridge,
src/southbridge and src/soc with the exception of src/soc/intel.
Change-Id: I78a9ce1cd0d790250a66c82bb1d8aa6c3b4f7162
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47982
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Create the drobit variant of the volteer reference board by copying
the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.2.0).
BUG=b:171947885
BRANCH=none
TEST=emerge-volteer coreboot
Signed-off-by: Frank Chu <frank_chu@pegatron.corp-partner.google.com>
Change-Id: I63b7312bba236bd5af028359804d042f6850d8ba
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47787
Reviewed-by: Zhuohao Lee <zhuohao@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
show_psp_transfer_info reimplemented the functionality of
transfer_buffer_valid, so use replace that with a function call.
Change-Id: Ie3d373b10bdb0ab00640dabeea12b13ec25406cc
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47977
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Change-Id: I4f07d3ab12116229a13d2e8c02b2deb06e51a1af
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47976
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Change-Id: I9e9fed26a686b8f90797687dd720902be48dae72
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47975
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
There will be more files added to the common non-CAR Makefile.inc, so
use an ifeq statement there.
Change-Id: I1f71954d27fbf10725387a0e95bc57f5040024cc
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47880
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Add a Kconfig symbol for including the PCIe MMCONF setup function in the
build and select it when SOC_AMD_COMMON_BLOCK_PCI is selected and in the
southbridges call enable_pci_mmconf(), but don't select
SOC_AMD_COMMON_BLOCK_PCI.
Change-Id: I32de7450bff5b231442f9f2094a18ebe01874ee7
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47878
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This pollutes the log on all platforms not implementing an override.
Change-Id: I0d8371447ee7820cd8e86e9d3d5e70fcf4f91e34
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48128
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Updating Imon slope and offset values as per recommendation of
ODM based on calibaration.
Updating Imon slope to 1.0 and offset to 1.4
BUG=b:167294777
BRANCH=dedede
TEST=Boot dedede platform and confirm values in FSP.
Change-Id: I3eb32218040163f0abef9b8dd4c52efb16289fe7
Signed-off-by: Meera Ravindranath <meera.ravindranath@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48072
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Vinay Kumar <vinay.kumar@intel.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
|
|
Create the sasuke variant of the waddledoo reference board by
copying the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.3.1).
BUG=b:172104731
BRANCH=None
TEST=util/abuild/abuild -p none -t google/dedede -x -a
make sure the build includes GOOGLE_SASUKE
Signed-off-by: Raymond Chung <raymondchung@ami.corp-partner.google.com>
Change-Id: I29405d63fd266224807e535c3f86a2ad5ab8cdf3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48112
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Henry Sun <henrysun@google.com>
Reviewed-by: SH Kim <sh_.kim@samsung.corp-partner.google.com>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
|
|
Remove the devices unused or not present on this laptop.
Signed-off-by: Mike Banon <mikebdp2@gmail.com>
Change-Id: I0decad499dfbb5f1e0a189d21f0fca47c80bd490
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47913
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
The current I2C5 bus frequency is 367 kHZ, which does not meet the spec.
This change updates scl_lcnt, scl_hcnt, scl_hcnt value for I2C5 to bring
the bus frequency closer to 400kHz.
BUG=b:173670150
TEST=Verified that I2C5 frequency is between 386-387kHz.
Signed-off-by: Frank Chu <frank_chu@pegatron.corp-partner.google.com>
Change-Id: I6d60abe15645dc51ed9ee30975d2521b8940c2d0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47736
Reviewed-by: Zhuohao Lee <zhuohao@google.com>
Reviewed-by: Zhuohao Lee <zhuohao@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Similar to the chipset.cb for TGL, this patch gives alias names to all
of the published PCI devices.
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I6576ef4237c1fc8439795ad5b64b1840504edf73
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48009
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Device ID for "D18:F6 - GSPI #2" shoud be 0xA0FB
BUG=none
TEST=Boot to OS, verify SSDT
Signed-off-by: Selma BENSAID <selma.bensaid@intel.com>
Signed-off-by: Bora Guvendik <bora.guvendik@intel.com>
Change-Id: I0d814170d24ff1b989eceb1d9ebdf6134df85e2e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48060
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I6289d2049fbbb6bb532be3d9e2355c563ec98d1b
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47410
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Tiger Lake introduces new wake-capable devices, including thunderbolt
ports, TCSS XHCI & XDCI as well as DMA ports. Add new ELOG_WAKE_SOURCE
macros for each of these types of devices.
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: Ie5dae6514c2776b30418a390c4da53bda0b2d456
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47395
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Add support for the following 5 LPDDR4x memory parts:
- MT53E512M64D4NW-046 WT:E
- H9HCNNNCRMBLPR-NEE
- MT53D1G64D4NW-046 WT:A
- H9HCNNNFBMBLPR-NEE
- MT53D512M64D4NW-046 WT:F
DRAM Part Name ID to assign
-------------------------------------------
MT53E512M64D4NW-046 WT:E 0 (0000)
H9HCNNNCRMBLPR-NEE 0 (0000)
MT53D1G64D4NW-046 WT:A 1 (0001)
H9HCNNNFBMBLPR-NEE 2 (0010)
MT53D512M64D4NW-046 WT:F 0 (0000)
BUG=b:172993397
TEST=none
Change-Id: Iff8f6257c6cff77fc3f0bda7e75434f9f4de1777
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47981
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add MT53D512M64D4NW-046 WT:F memory part to LP4x global list of
available LP4x parts and to the global JSON file containing LP4x parts
and their characteristics.
BUG=b:172993397
TEST=none
Change-Id: I09c6eab640c169dbdb451964967d14a31e314496
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47980
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Rob Barnes <robbarnes@google.com>
|
|
This allows dropping ugly preprocessor usage from this file.
Change-Id: Idb66d295129d98725f38d11ac162978418bd94c2
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47959
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Having variants' gpio.c call the `gpio_configure_pads` function results
in an API that does not need to pass data around, which is much simpler.
Change-Id: I1064dc6258561bcf83f0e249d65b823368cf0d31
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47958
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
|
|
Most of the existing comments are C-style already.
Change-Id: I9ca4779f5b0560320e9bce4f33e54766522689f9
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47957
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
|
|
Change-Id: Ie347ee508acd900353467b4a3e0a5d1928b110e1
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47877
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
If there are multiple statements that are conditional on the same
Kconfig option, group them and move the condition check around the
statement. If there's only one statement depending on one condition, use
the short form instead.
Change-Id: I89cb17954150c146ffc762d8cb2e3b3b374924de
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47876
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Since there are sub-directories for both the cache-as-RAM case and the
non-CAR case where the RAM is already initialized when the x86 cores are
released from reset, move the CAR-specific parts of the Makefile.inc to
another Makefile.inc in the car sub-directory. Further patches will add
a Makefile.inc to the non-CAR directory.
Change-Id: I43a3039237d96e02baa33488e71c5f24effe8359
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47875
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Commit bd31642ad8 (intel/i210: Set bus master bit in command register)
is only necessary because a buggy OS expects Bus Master to be set, not
because the hardware requires Bus Master during initialization. It is
thus safe to defer the Bus Master request into the .final callback.
Change-Id: Iecfa6366eb4b1438fd12cd9ebb1a77ada97fa2f6
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47401
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Tested-by: siemens-bot
|
|
There's one copy of this function for all variants except mc_apl4. Move
one copy into common mainboard.c and exit early if running on mc_apl4.
Change-Id: I4e35b58adc074831ccec433b8e014db0695b955e
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47402
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
A MAC address that is neither 00:00:00:00:00:00 nor ff:ff:ff:ff:ff:ff is
considered valid. Instead of using a temporary buffer and memcmp(), use
a single loop that exits as soon as the MAC cannot possibly be invalid.
Change-Id: I2b15b510092860fbbefd150c9060da38aeb13311
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47405
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Uwe Poeche <uwe.poeche@siemens.com>
|
|
Define and use the MAC_ADDR_LEN macro in place of the `6` magic value.
Change-Id: Icfa2ad9bca6668bea3d84b10f613d01e437ac6a2
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47404
Tested-by: siemens-bot
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
Break down multi-line compound conditions into multiple if-statements,
and leverage `continue` statements to avoid nesting multiple checks.
Change-Id: I5edc279a57e25a0dff1a4b42f0bbc88c0659b476
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47403
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Tested-by: siemens-bot
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Uwe Poeche <uwe.poeche@siemens.com>
|
|
Now that soc_get_pmc_mux_device() is gone, the PMC MUX connector devices
can be hooked up together via devicetree aliases.
BUG=b:172528109
BRANCH=firmware-volteer-13521.B
TEST=built and USB3.0, type-c display work.
Signed-off-by: Scott Chao <scott_chao@wistron.corp-partner.google.com>
Change-Id: Iedf9b972b341064ff62a4443bfa83f69c8c60108
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48066
Reviewed-by: Zhuohao Lee <zhuohao@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change updates bootblock_pch_early_init() to perform P2SB
configuration before any other PCH controllers are initialized. This
is done because the other controllers might perform PCR settings which
requires the PCR base address to be configured. As the PCR base
address configuration happens during P2SB initialization, this change
moves the p2sb init calls before any other PCH controller
initialization.
BUG=b:171534504
Change-Id: I485556be003ff5338b4e2046768fe4f6d8a619a3
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47885
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
TEST=Able to pass LPDDR5 MRC training with Lp5CccConfig override.
Signed-off-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Change-Id: I24b1cf50c1b0b945fce75239bac38e40aeb8a83a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47436
Reviewed-by: V Sowmya <v.sowmya@intel.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
TEST=Able to pass MRC training on DDR4/5 SKUs
Change-Id: I38fcb17a1be5a8544a17cef8255631b6abef0741
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48078
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Reviewed-by: V Sowmya <v.sowmya@intel.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Set the FADT PM profile to ENTERPRISE_SERVER, since the currently
supported X11 boards are server boards.
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: I8fb5c7c262fbd3f3c085d7c2e2ef3d6ff6ce73eb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48088
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Rework gpio setup for the board series to not use headers but
stage-specific compilation units.
Tested successfully on X11SSM-F.
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: Ic62ce4335af605c081ef288e892441585ff2bd3e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48087
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
|
|
GPIO needs to be initialized before the IPMI device gets initialized,
so the GPIOs can be read/set by the code in CB:48096 and CB:48094. Thus,
use mainboard_ops.init for GPIO configuration instead of using the
indirection via a mainboard_enable function.
To make it more visible, that we use chip.init, rename `mainboard_init`
to `mainboard_chip_init`.
Tested successfully on X11SSM-F including the IPMI changes.
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: I192e69a34fa262b38bc40a95fb11c22a4041d0ae
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48083
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
The ITSS override is not needed for LPC_CLKOUT* pads. Drop it.
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: I3dbbc8944751779151dcd4f92fb870d937801d69
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48084
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Move gpio configuration from the Fsp callback to mainboard init.
Tested successfully on X11SSM-F.
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: If2a54c75c5243d94cdc025c597ee347820b35d32
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48086
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Drop zero-value devicetree options and move PcieRpEnable options down to
the corresponding devices.
Test: built with TIMELESS=1; binaries remain identical
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: I9285d786e973621a732e2627c734adc930e54207
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48082
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Commit 056d552 introduced a bug where 0xFF gets set as OC pin value to
supposedly skip programming an OC pin for a disabled USB port. While the
value is correct for the other platforms, Skylake uses 0x08 for this
purpose. Correct this by using the enum value OC_SKIP (0x08) instead.
Change-Id: I41a8df3dce3712b4ab27c4e6e10160b2207406d1
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48003
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
|
|
Drop the TODO comment, since there is no TODO left. Also drop the now
obsolete TODO section from the board documentation.
Change-Id: I4192aaedc1429c8ff1bd7c52baa4741e1df0d0c5
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48126
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
|
|
This can be done using in the INTERMEDIATE target in the proper place.
Change-Id: I28a7764205e0510be89c131058ec56861a479699
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46453
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Christian Walter <christian.walter@9elements.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Update UPDs required for the creation of DMAR table.
By default coreboot was not generating DMAR table for IOMMU which
was resulting in below error message in kernel:
DMAR: [Firmware Bug]: No DRHD structure found in DMAR table
DMAR: No DMAR devices found
These changes will publish DMAR table through ACPI and will not
result in the above error.
BUG=b:170261791
BRANCH=dedede
TEST=Build Dedede, boot to kernel and check dmesg if DMAR
table exists.
Signed-off-by: Meera Ravindranath <meera.ravindranath@intel.com>
Change-Id: I97a9f2df185002a4e58eaa910f867acd0b97ec2b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47506
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
|