aboutsummaryrefslogtreecommitdiff
path: root/src
AgeCommit message (Collapse)Author
2018-03-27soc/intel/skylake: Add NHLT config for max98373 codecDuncan Laurie
Add the NHLT configuration for the max98373 codec to skylake, taken directly from cannonlake. This will allow skylake/kabylake boards to use this codec. Change-Id: Ifb6bf2d31fda25b18d9b1ce2bb721255335d55e4 Signed-off-by: Duncan Laurie <dlaurie@google.com> Reviewed-on: https://review.coreboot.org/25367 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: HARSHAPRIYA N <harshapriya.n@intel.com> Reviewed-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
2018-03-27mainboard/google/poppy: Add SPD for Hynix H9CCNNNCLGALAR-NUDDuncan Laurie
Add an SPD for this particular Hynix memory type to the poppy board so it can be used by poppy variants. BUG=b:75454415 Change-Id: I2249c7a4f2c83ec2b3266047a74b9bc22dad43be Signed-off-by: Duncan Laurie <dlaurie@google.com> Reviewed-on: https://review.coreboot.org/25368 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2018-03-27soc/intel/skylake: Do a heci_reset before reading ME firmware versionFurquan Shaikh
This change adds a call to heci_reset before attempting to read ME firmware version. This is important to ensure that both ME and BIOS are in sync. BUG=b:76167737 BRANCH=poppy TEST=Verfied that ME firmware version read does not fail on first boot after power failure (i.e. removing battery and AC power). Change-Id: Ib6b39c398d2e1177b087352a4acb8bcf5a9897d6 Signed-off-by: Furquan Shaikh <furquan@google.com> Reviewed-on: https://review.coreboot.org/25362 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2018-03-27mb/google/octopus: Remove emmc tuning parameters from devicetreeFurquan Shaikh
Current emmc tuning parameters for octopus were copied over from other boards and result in failure to boot from emmc. This change gets rid of the emmc tuning parameters in devicetree. Once emmc tuning tests are run for octopus, these parameters can be added back. BUG=b:75986903 BRANCH=None TEST=Verified that octopus boots from eMMC without any errors in depthcharge. Change-Id: I7ac44a54afd1ecfe355a9654ac8e92133b67637f Signed-off-by: Furquan Shaikh <furquan@google.com> Reviewed-on: https://review.coreboot.org/25375 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Justin TerAvest <teravest@chromium.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2018-03-26vboot: Update to most recent GBB flag usageJulius Werner
This patch changes the GBB flag configuration to the latest usage in upstream vboot (as of https://chromium-review.googlesource.com/976660). Change-Id: I585d662d7de34b4964d028e3d06b4df5665fbe9e Signed-off-by: Julius Werner <jwerner@chromium.org> Reviewed-on: https://review.coreboot.org/25346 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2018-03-26ec/purism: Fix CPU Turbo value (PPCM) set by the ECYouness Alaoui
The EC needs to set the PPCM value depending on whether Turbo is enabled or not, and the values differ between Broadwell (0, 1) and Skylake (1, 2) platforms. Change-Id: I662dce54415e685c054ffc00b6afde0f1f7765e2 Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm> Reviewed-on: https://review.coreboot.org/25329 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
2018-03-26purism/librem13v1, librem13v2, liberm15v3: Fix EC LPC I/O portYouness Alaoui
The LPC I/O ports for EC communication were not set properly, causing ectool to fail to read the Index I/O from the EC. The EC Index I/O is on port 0x380 and the LPC I/O port needs to be decoded by the PCI device for it to be accessible. Correct the value for the Librem 13v1, 13v2 and 15v3. Change-Id: Ide1d158340eadfabbce5f70ceccddfabb4db188a Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm> Reviewed-on: https://review.coreboot.org/25328 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
2018-03-26mb/google/poppy/variant/nautilus: Turn off MIPI camera in PMOF methodSeunghwan Kim
This change remove work-around code for the power issue of MIPI and USB cameras on previous board revision. With the work-around code, PMOF ACPI method cannot turn off MIPI camera. So we need to remove it. BUG=b:74214248 BRANCH=poppy TEST=emerge-nautilus coreboot Change-Id: I7becaf61de364f82976ec0be7f8c9e4ef1a7aedd Signed-off-by: Seunghwan Kim <sh_.kim@samsung.com> Reviewed-on: https://review.coreboot.org/25337 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2018-03-26mainboard/hp: Add Elitebook Folio 9470mBill XIE
The code is based on autoport and that for revolve_810g1 Tested: - CPU i5-3437U - Slotted DIMM 8GiB - Onboard USB2 interfaces (wlan slot, wwan slot, camera, smart card) - Mini pci-e on wlan slot - On board SDHCI connected to pci-e - USB3 ports - USB3 hub on dock (connected to USB3 port 1) - NVRAM options for North and South bridges - S3 - TPM1 on LPC - Linux 4.13.17-1 within Debian GNU/Linux testing, loaded from SeaBIOS, or Linux payload (Heads) Not tested: - Fingerprint reader on USB2 Not working well: - EHCI debug on port SSP2,(The USB port on the left, wired to ehci before OS) it has always-on enabled by default (maybe via EC), which disturbs FT232H's own power up, requiring a very critical timing to plug it in for it to work. Change-Id: I52e549ec18e8aa661a506a16dbc7f83417c0da78 Signed-off-by: Bill XIE <persmule@gmail.com> Reviewed-on: https://review.coreboot.org/25218 Reviewed-by: Patrick Rudolph <siro@das-labor.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2018-03-26mainboard/google/cheza: Add support for ChezaT Michael Turney
TEST=build Change-Id: I32d185741ce20a3a82e6895de3026ade52d0bcc8 Signed-off-by: T Michael Turney <mturney@codeaurora.org> Reviewed-on: https://review.coreboot.org/25200 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Julius Werner <jwerner@chromium.org>
2018-03-26soc/qualcomm/sdm845: Support for new SoCT Michael Turney
TEST=build Change-Id: Ie54e310a94f61b8d86c13261937015e3f5a2ab01 Signed-off-by: T Michael Turney <mturney@codeaurora.org> Reviewed-on: https://review.coreboot.org/25199 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Julius Werner <jwerner@chromium.org>
2018-03-26drivers/intel/fsp: Fix TPM initialization when vboot is disabledYouness Alaoui
A change introduced by commit fe4983e5 [1] in order to prevent re-initialization of the TPM if already set up in verstage had the wrong logic in the if statement, causing the TPM to never be initialized if vboot is disabled. The RESUME_PATH_SAME_AS_BOOT config is enabled by default for ARCH_X86, resulting in the if statement to always evaluate to false. Remove that condition from the if statement to allow it to function as intended. This patch also enables TPM initialization for FSP 2.0 with the same conditions. [1] intel/fsp1_1: Do not re-init TPM in romstage if already setup in verstage https://review.coreboot.org/#/c/coreboot/+/14106/ Change-Id: Ic43d1aa31a296386c7eab6d997f9b701e9ea0fe5 Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm> Signed-off-by: Matt DeVillier <matt.devillier@gmail.com> Reviewed-on: https://review.coreboot.org/23680 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2018-03-26soc/intel: Add KBL-S MCH and some KBL PCH supportGaggery Tsai
This patch adds the support for KBL-S MCH and Z270, H270, B250 and Q250 PCH chips. BUG=None BRANCH=None TEST=Boot with KBL-S CPU and B250/H270 PCHs. Change-Id: If03abb215f225d648505e05274e2f08ff02cebdc Signed-off-by: Gaggery Tsai <gaggery.tsai@intel.com> Reviewed-on: https://review.coreboot.org/25305 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Naresh Solanki <naresh.solanki@intel.com>
2018-03-26soc/skylake/cpu: Fix Intel SpeedStep enable/disableMatt DeVillier
In an attempt at consolidation, commit 0a203d1 [1] introduced an additional read/write of the MISC_ENABLE msr, as well a bug which nullified the setting of Intel SpeedStep by inserting said read/write calls in between another set of read/write calls to the same msr. Fix by reverting to previous (simpler) implementation. [1] soc/intel/skylake: Use CPU common library code https://review.coreboot.org/19566 Test: boot Linux on Librem13v2, read MISC_ENABLE msr and verify SpeedStep bit correctly set based on devicetree setting. Change-Id: Id2ac660bf8ea56d45e8c3f631a586b74106a6cc9 Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm> Signed-off-by: Matt DeVillier <matt.devillier@gmail.com> Reviewed-on: https://review.coreboot.org/25330 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2018-03-26mb/octopus: Set PNP config to PNP_PERF_POWERShaunak Saha
This patch sets the PNP config value to PNP_PERF_POWER. The config values for soc can be found in chip.h TEST = Build for octopus. Change-Id: I2239aa70cb708e6e1c06339ca9d517e7eaa198ed Signed-off-by: Shaunak Saha <shaunak.saha@intel.com> Reviewed-on: https://review.coreboot.org/25310 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Furquan Shaikh <furquan@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2018-03-26lib/lzma: Respect dstn argumentPatrick Rudolph
Don't write more bytes than the caller requests. Based on I484b5c1e3809781033d146609a35a9e5e666c8ed. Change-Id: I336de417c7cd6f35cf84947fc4ae161c15bd93ef Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com> Reviewed-on: https://review.coreboot.org/25222 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Patrick Georgi <pgeorgi@google.com>
2018-03-25mb/glkrvp: Set PNP config to PNP_PERF_POWERShaunak Saha
This patch sets the PNP config value to PNP_PERF_POWER. The config values for soc can be found in chip.h TEST = Built and booted glkrvp, verified warm and cold reboot and suspend resume. Change-Id: Ia390c0fafe2de64bd9e4ca44e5ed5d904663ae3c Signed-off-by: Shaunak Saha <shaunak.saha@intel.com> Reviewed-on: https://review.coreboot.org/25309 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2018-03-24mb/google/octopus: Select TPM options only if mocktpm is not selectedFurquan Shaikh
This change adds a new Kconfig option for mainboard octopus "HAS_TPM" that auto-selects all TPM related options only if VBOOT_MOCK_SECDATA is not selected. BUG=b:76203913 TEST=Compiles fine with mocktpm. Change-Id: Ib28fc47a70be58cd9a9ec65ce3b1cda68d558437 Signed-off-by: Furquan Shaikh <furquan@google.com> Reviewed-on: https://review.coreboot.org/25340 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Justin TerAvest <teravest@chromium.org> Reviewed-by: Jett Rink <jettrink@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2018-03-23soc/amd: Print dimm_info and TYPE17_DMI_INFO to help debug incorrect valuesRaul E Rangel
Example output: AGESA TYPE 17 DMI INFO: Handle: 1 TotalWidth: 64 DataWidth: 64 MemorySize: 8192 DeviceSet: 0 Speed: 1200 ManufacturerIdCode: 44416 Attributes: 1 ExtSize: 0 ConfigSpeed: 933 MemoryType: 0x1a FormFactor: 0xd DeviceLocator: DIMM 0 BankLocator: CHANNEL A SerialNumber(8): 00000000 PartNumber(20): HMAA51S6AMR6N-UH CBMEM_ID_MEMINFO: dimm_size: 0 ddr_type: 0x1a ddr_frequency: 1200 rank_per_dimm: 1 channel_num: 0 dimm_num: 0 bank_locator: 0 mod_id: 44416 mod_type: 0x1a bus_width: 64 serial(4): 0000 module_part_number(23): HMAA51S6AMR6N-UH ��@ dimm_size, mod_type, bus_width need to be updated so they return the correct values. module_part_number is missing a null terminator due to the AGESA part number being larger than the dimm_info buffer. Example dmidecode output: Memory Device Array Handle: 0x0000 Error Information Handle: Not Provided Total Width: 8 bits Data Width: 8 bits Size: No Module Installed Form Factor: Unknown Set: None Locator: Channel-0-DIMM-0 Bank Locator: BANK 0 Type: DDR4 Type Detail: Synchronous Speed: 1200 MT/s Manufacturer: Hynix/Hyundai Serial Number: 0000 Asset Tag: Not Specified Part Number: HMAA51S6AMR6N-UH Rank: 1 Configured Clock Speed: 1200 MT/s Minimum Voltage: Unknown Maximum Voltage: Unknown Configured Voltage: Unknown To enable the output set CONFIG_DEBUG_RAM_SETUP. The Kconfig change is required in order to enable CONFIG_DEBUG_RAM_SETUP, otherwise it's not a valid option. BUG=b:65403853 TEST=Test output shown above Signed-off-by: Raul E Rangel <rrangel@chromium.org> Change-Id: I5eac00b9400056357915761287770a400b3f9f8b Reviewed-on: https://review.coreboot.org/25303 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2018-03-23arch/x86/smbios: Strip trailing whitespace on DMI 17 part number.Raul E Rangel
dmidecode used to print 'HMAA51S6AMR6N-UH ' it now prints 'HMAA51S6AMR6N-UH' BUG=b:65403853 TEST=Verified using dmidecode Signed-off-by: Raul E Rangel <rrangel@chromium.org> Change-Id: Ia10ef434a2377e34ae7a8f733c6465c2f8ee8dfa Reviewed-on: https://review.coreboot.org/25302 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2018-03-23include: Update dimm_info documentationRaul E Rangel
Reference the JEDEC SPD spec and clarify some comments. BRANCH=dimm-info BUG=b:65403853 TEST=Documentation change only Signed-off-by: Raul E Rangel <rrangel@chromium.org> Change-Id: I1f2a3a70919c34f17472904323ec5accdfc876be Reviewed-on: https://review.coreboot.org/25301 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2018-03-23mainboard/intel/cannonlake_rvp: Enable S0ixVaibhav Shankar
This patch enables S0ix from the devicetree. Change-Id: I38662dc7203366bdee5f1c7aaa18979867a79ba1 Signed-off-by: Vaibhav Shankar <vaibhav.shankar@intel.com> Reviewed-on: https://review.coreboot.org/25293 Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com> Reviewed-by: Furquan Shaikh <furquan@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2018-03-23soc/intel/cannonlake: Enable low power S0 Idle capabilityVaibhav Shankar
This patch sets the ACPI FADT flag ACPI_FADT_LOW_POWER_S0 if S0ix is enabled for the platform. This also sets the FSPUPD to indicate the status of S0ix on the platform. TEST= Boot to OS and check the ACPI_FADT_LOW_PWR_IDLE_S0 flag is set in FACP table - FADT.Flags[21] bit. Change-Id: I6214ebb61f25ef8b704e60c8474808493c92e6f6 Signed-off-by: Vaibhav Shankar <vaibhav.shankar@intel.com> Reviewed-on: https://review.coreboot.org/25292 Reviewed-by: Furquan Shaikh <furquan@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2018-03-23mb/google/zoombini: always report EC is in RO modeNick Vaccaro
Always report that EC is in RO mode. This is a temporary workaround for a hardware issue that is causing EC to appear to be in RW mode when it is not. This change will be reverted once transition is made to newer hardware. BUG=b:74215817 BRANCH=master TEST=Verify meowth can boot to recovery's insert screen. Change-Id: Ib3705bba0bb1f351da79e599566fbffab94428f3 Signed-off-by: Nick Vaccaro <nvaccaro@google.com> Reviewed-on: https://review.coreboot.org/25298 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2018-03-23mb/intel/kblrvp8: Add KBLRVP8 supportV Sowmya
Add the config for setting SPD DIMM size to 512 bytes for KBLRVP8 with DDR4 memory. Configure the DIMM1 memory SPD data for channel0 and channel1. Set the UserBd UPD to BOARD_TYPE_DESKTOP for kblrvp8. Signed-off-by: V Sowmya <v.sowmya@intel.com> Change-Id: I985968d331991884050c3920ec9798cd4cb371c7 Reviewed-on: https://review.coreboot.org/25194 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Naresh Solanki <naresh.solanki@intel.com>
2018-03-23arch/arm64/armv8/mmu: Add support for 48bit VAPatrick Rudolph
The VA space needs to be extended to support 48bit, as on Cavium SoCs the MMIO starts at 1 << 47. The following changes were done to coreboot and libpayload: * Use page table lvl 0 * Increase VA bits to 48 * Enable 256TB in MMU controller * Add additional asserts Tested on Cavium SoC and two ARM64 Chromebooks. Change-Id: I89e6a4809b6b725c3945bad7fce82b0dfee7c262 Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com> Reviewed-on: https://review.coreboot.org/24970 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Julius Werner <jwerner@chromium.org>
2018-03-23soc/intel/apollolake: Bypass FSP's deassertion of PERST# signal.Shamile Khan
BUG=b:76058338 BRANCH=None TEST=Build coreboot for Octopus board. Change-Id: I1858c7843d16b6b63fc30762a889916bbb9b781a Signed-off-by: Shamile Khan <shamile.khan@intel.com> Reviewed-on: https://review.coreboot.org/25311 Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2018-03-23vendorcode/intel: Update FSP Header files per v2.0.0Srinidhi N Kaushik
Update FSP header files to match GLK FSP Reference Code Release v2.0.0 Change-Id: I93d95e1977a4e31981e8b91882059611d91f78a5 Signed-off-by: Srinidhi N Kaushik <srinidhi.n.kaushik@intel.com> Reviewed-on: https://review.coreboot.org/25247 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2018-03-22mb/google/zoombini: Enable NVMeNick Vaccaro
BUG=b:72120814 BRANCH=master TEST=none Change-Id: I64ab38dda78345c1f3d7d3f2bf3cb04c19290ceb Signed-off-by: Nick Vaccaro <nvaccaro@google.com> Reviewed-on: https://review.coreboot.org/25256 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2018-03-22mb/google/octopus: Add CLKREQ and de-emphasis settings for PCIe Wi-FIShamile Khan
BUG=b:73292699 BRANCH=None TEST=Build coreboot for Octopus board. Change-Id: Ic73ad38ad9a12bec614e530f7f35619246b9f57f Signed-off-by: Shamile Khan <shamile.khan@intel.com> Reviewed-on: https://review.coreboot.org/25288 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Furquan Shaikh <furquan@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2018-03-22amd/stoneyridge: Add PM1 wake status to boot logMarshall Dawson
Print the wake status bits to the console. The format is kept similar to Intel's to maintain compatilibity with inspection utilities. Add relevant wake events from the register to the ELOG. Clear the register before continuing. TEST=Inspect console and ELOG for Grunt BUG=b:75020968 Change-Id: Idc9d12326abb290e4f7a5c60677eb6e057d475b2 Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com> Reviewed-on: https://review.coreboot.org/25300 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Martin Roth <martinroth@google.com> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
2018-03-22intel/fsp: Update Cannonlake FSP headerLijian Zhao
Update Cannonlake FSP header to version 7.x.2A.20, the following changes were made: 1. Add MemtestonWarmBoot option. 2. Add enable8254clockgatingonS3 option. 3. Default disable Tccoffsetlock BUG=None TEST=None Change-Id: Ie794960f0253b2a6dbd55ffda973756d15e35c01 Signed-off-by: Lijian Zhao <lijian.zhao@intel.com> Reviewed-on: https://review.coreboot.org/25289 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Caveh Jalali <caveh@google.com> Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
2018-03-22soc/intel/skylake: Define IFD_CHIPSETFurquan Shaikh
This change defines IFD_CHIPSET as sklkbl to allow ifdtool to set the right access control bits for SKL/KBL platforms. BUG=b:76098647 BRANCH=poppy TEST=Verified that the access control bits on KBL platforms are set correctly. Change-Id: I7b2131caa06d6a975e703262931ec0ea519a86aa Signed-off-by: Furquan Shaikh <furquan@google.com> Reviewed-on: https://review.coreboot.org/25307 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2018-03-21mb/google/fizz: Enable I2C bus 2Zhongze Hu
I2C bus 2 goes to the custom add-in card slot and it was disalbed cuase it was idle. Google CFM add-in card is going to use this I2C bus so it needs to be re-enabled. BUG=b:73006317 TEST=Tested with add-in card on fizz hardware and verified I2C bus 2 is working properly. Change-Id: I2c9b5a9323fd51872e340c35005c4a3432716808 Signed-off-by: Zhongze Hu <frankhu@chromium.org> Reviewed-on: https://review.coreboot.org/25258 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Shelley Chen <shchen@google.com>
2018-03-21mb/intel/glkrvp: Re-size flash WP_RO segmentSrinidhi N Kaushik
Update the size in WP_RO segment of the flash to accommodate builds using debug FSP. Change-Id: I8b24422e1eef2d0a81006286d4fc58f238fdce11 Signed-off-by: Srinidhi N Kaushik <srinidhi.n.kaushik@intel.com> Reviewed-on: https://review.coreboot.org/25255 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Furquan Shaikh <furquan@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2018-03-21mb/google/octopus: Re-size flash WP_RO segmentSrinidhi N Kaushik
Update the size in WP_RO segment of the flash to accommodate builds using debug FSP. Change-Id: I0a0d1d0121b503ff390adf3ce25973d72e59fdeb Signed-off-by: Srinidhi N Kaushik <srinidhi.n.kaushik@intel.com> Reviewed-on: https://review.coreboot.org/25253 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2018-03-21mb/google/octopus: Create bip variantJustin TerAvest
This creates a bip variant for octopus. Nothing is set in the variant files here-- everything is picked up from baseboard. BUG=b:75976864 TEST=None Change-Id: I7a8ac3d8bb71416f05ef1a605684d92d5902abda Signed-off-by: Justin TerAvest <teravest@chromium.org> Reviewed-on: https://review.coreboot.org/25285 Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2018-03-21mainboard/google/kahlee: Update GPIOs based on board IDMartin Roth
BUG=b:73078053 TEST=build & boot Grunt Change-Id: I2d4ba197b19c4948b867a61575e858b2a826a286 Signed-off-by: Martin Roth <martinroth@chromium.org> Reviewed-on: https://review.coreboot.org/25287 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2018-03-21mb/google/poppy/variants/nami: change type of board_sku_id() to uint32_tZhuohao Lee
Tools/scripts, like mosys/arc-setup, use int (4 bytes) to read the sku id. In order to support "-1", we need to use uint32_t (4 bytes) instead of using uint16_t (2 bytes) data type. Otherwise, tools/scripts will read 65535 instead of -1. Another reason to change this is that sku_id can be supported by ec up to 4 bytes. BUG=b:73792190 TEST=mosys output "Platform not supported" for -1 sku id arc-setup read -1 sku id Change-Id: Ib3baa8419f138abeb412ac09c2e7dc608e3b758b Signed-off-by: Zhuohao Lee <zhuohao@chromium.org> Reviewed-on: https://review.coreboot.org/25252 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2018-03-21mb/google/octopus: Enable TPM on GSPIRavi Sarawadi
BUG=b:73133848 BRANCH=None TEST=Build coreboot for Octopus board. Tested the GSPI interface with a SPI EEPROM and got correct response to a RDID command Change-Id: Ia10ab9da0055b54a96134a6e4c51b2a229a6fecf Signed-off-by: Ravi Sarawadi <ravishankar.sarawadi@intel.com> Reviewed-on: https://review.coreboot.org/24907 Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2018-03-21drivers/i2c/designware: Fix indentationMaulik V Vaghela
Remove extra tab before printk statement. Change-Id: Id82239f74ac030f25000a08764637f6d1b52b87b Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com> Reviewed-on: https://review.coreboot.org/25295 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Naresh Solanki <naresh.solanki@intel.com> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2018-03-21mb/google/poppy/variant/nautilus: Enable CABC feature as defaultSeunghwan Kim
This change configures GPP_E22 to GPO_HIGH to enable CABC feature on nautilus board. BUG=b:68789889 BRANCH=poppy TEST=emerge-nautilus coreboot Signed-off-by: Seunghwan Kim <sh_.kim@samsung.com> Change-Id: Ifed0d37bf8147aa1b580f594f36f186051c2eb52 Reviewed-on: https://review.coreboot.org/25120 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Furquan Shaikh <furquan@google.com>
2018-03-21mb/google/kahlee: Add register address mapping for FCH MISCAkshu Agrawal
Audio machine driver will enable/disable clock by making it as a CCF clock in kernel. BUG=b:74570989 TEST=cherry-picked https://patchwork.kernel.org/patch/10291875/ on 4.14 kernel aplay -vv <file> check register to see clock enabled kill aplay check register to see clock disabled Change-Id: Ia553e55ffb358415067000d2d2d2744322d1c4db Signed-off-by: Akshu Agrawal <akshu.agrawal@amd.com> Reviewed-on: https://review.coreboot.org/25263 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2018-03-20mainboard/google/kahlee: Initialize EC earlier in the bootblockMartin Roth
Set up the EC communication a little earlier so we can read the board ID before programming GPIOS. BUG=b:73078053 TEST=Build & Boot grunt, board_id() now gets ID correctly Change-Id: Icf3f598824cfed69fa03ba2bb86503bb3c3699a5 Signed-off-by: Martin Roth <martinroth@chromium.org> Reviewed-on: https://review.coreboot.org/25286 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2018-03-20soc/intel/apollolake: Add support for GSPIRavi Sarawadi
BUG=b:73133848 BRANCH=None TEST=Build coreboot for Octopus board. Tested the GSPI interface with a SPI EEPROM and got correct response to a RDID command Change-Id: Iec96f926ba7162074090617b7cf1c84e36b0fb37 Signed-off-by: Ravi Sarawadi <ravishankar.sarawadi@intel.com> Signed-off-by: Hannah Williams <hannah.williams@intel.com> Reviewed-on: https://review.coreboot.org/24906 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2018-03-19drivers/intel/wifi: Add Jefferson Peak Device IDLijian Zhao
The following PCI device ID can be included for jefferson peak wifi devices driver support, and they are: 9df0 for jefferson peak on Cannonlake-LP w/CNVi A370 for jefferson peak on Cannonlake-H w/CNVi 31dc for jefferson peak on Geminilake w/CNVi BUG=None TEST=None Change-Id: I48886cea5578a302f6ef033cb35df4a38bd64ea8 Signed-off-by: Lijian Zhao <lijian.zhao@intel.com> Reviewed-on: https://review.coreboot.org/25146 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2018-03-19mb/google/octopus: Configure PERST_0 pinJustin TerAvest
According to the schematic, Octopus boards have WLAN_PE_RST connected to GPIO_164. This change configures that properly in devicetree. BUG=None TEST=None Change-Id: I2ba4839e036f02c5e0316d08599894879133894a Signed-off-by: Justin TerAvest <teravest@chromium.org> Reviewed-on: https://review.coreboot.org/25248 Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2018-03-19mb/google/octopus: Fix GPIO config for DRAM_IDsJustin TerAvest
The GPIO pad configurations for GPIO68-71 are incorrectly configured as outputs. This change corrects them to be inputs. BUG=b:74932341 TEST=None Change-Id: I319f8a64d83c29ed150316c15a8d429cc7c024f3 Signed-off-by: Justin TerAvest <teravest@chromium.org> Reviewed-on: https://review.coreboot.org/25217 Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2018-03-19mb/google/poppy: Config GPIO for DMIC by different sku idamanda_hwang
BUG=b:74177699 BRANCH=poppy TEST=Verify audio recorder function by different SKU ID Change-Id: Ic6570703f6ab4a1b03cbba8370fc0f597ab6bcf2 Signed-off-by: amanda_hwang <amanda_hwang@compal.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/25148 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2018-03-19soc/intel/apollolake: Add PCIe de-emphasis enable configuration.Shamile Khan
PCIe de-emphasis is enabled by default. Thunderpeak Wi-Fi requires it to be disabled. Therefore allow it to be configured via a device tree setting. TEST=On GLKRVP, verify Thunderpeak Wi-Fi card shows up in lspci when de-emphasis is disabled in device tree. Change-Id: Iae204768dfe00a638c764644c44c7cda269e73e0 Signed-off-by: Shamile Khan <shamile.khan@intel.com> Reviewed-on: https://review.coreboot.org/25185 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Furquan Shaikh <furquan@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2018-03-19mb/google/octopus: Configure PCH_WP_OD early.Justin TerAvest
The GPIO for EEPROM write-protect should be configured early, before romstage. This change configures that pad earlier. This pad is the same on the existing Octopus schematics. BUG=None TEST=None Change-Id: Idf296ba6aad75b890afabd6f7c7c51fbaf911214 Signed-off-by: Justin TerAvest <teravest@chromium.org> Reviewed-on: https://review.coreboot.org/25250 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2018-03-19mb/google/fizz: Enable VMXShelley Chen
We are enabling at the kernel level, but that is triggering an issue where FSP expects it to be disabled so it forces a cold reboot on every warm reboot, clearing the ramoops logs. Enabling in BIOS so it matches what the kernel expects. This is the same change that were done for eve: https://review.coreboot.org/#/c/22449/ BUG=None BRANCH=None TEST=echo PANIC > /sys/kernel/debug/provoke-crash/DIRECT check for /dev/pstore/console-ramoops Change-Id: Icd0bd01f5aee4c89f503eebba0808a1f3059e739 Signed-off-by: Shelley Chen <shchen@chromium.org> Reviewed-on: https://review.coreboot.org/25251 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2018-03-19soc/amd/stoneyridge/southbridge.c: Remove configure_stoneyridge_uartRichard Spiegel
The GPIO programming of configure_stoneyridge_UART() can be done by the early GPIO table, AOAC enabling was already removed. So configure_stoneyridge_uart() became redundant. Remove procedure configure_stoneyridge_uart(). BUG=b:74258015 TEST=Build and boot kahlee, observing serial output does not changes from previous serial output. Change-Id: Ie67051d7b90fa294090f6bfc518c6c074d98cc98 Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com> Reviewed-on: https://review.coreboot.org/25192 Reviewed-by: Garrett Kirkendall <garrett.kirkendall@amd.corp-partner.google.com> Reviewed-by: Martin Roth <martinroth@google.com> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2018-03-17mb/google/octopus: Do not configure GPIO_149 as GPOFurquan Shaikh
GPIO_149 is used as ESPI clock feedback and configuring it as a GPO results in EC communication failure. This change removes the configuration of GPIO_149 as GPO in ramstage so that it remains configured for ESPI (as it was when AP came out of reset). BUG=b:75348718 Change-Id: Ie4f21b12fae027cdba54ce147e6d1a88ee854792 Signed-off-by: Furquan Shaikh <furquan@google.com> Reviewed-on: https://review.coreboot.org/25259 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Justin TerAvest <teravest@chromium.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2018-03-17soc/amd/stoneyridge: Call sb_spibase() earlyGarrett Kirkendall
Call sb_spibase() early so that it will set up the SPI base address. This is another step to moving AGESA calls out of the bootblock. BUG=b:74427893 BRANCH=master TEST=Build and boot Grunt. Change-Id: I665d32f3acb0046eb6abbd363735561f0372f2a0 Signed-off-by: Garrett Kirkendall <garrett.kirkendall@amd.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/25246 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2018-03-17soc/intel/apollolake: handle different memory profiles for apl and glkAaron Durbin
glk has different memory profile values than apl. Therefore, a translation is required to correctly set the proper profile value depending on what SoC (and therefore FSP) is being used. Based on SOC_INTEL_GLK Kconfig value use different profiles. BUG=b:74932341 Change-Id: I6ea84d3339caf666aea5034ab8f0287bd1915e06 Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: https://review.coreboot.org/25249 Reviewed-by: Justin TerAvest <teravest@chromium.org> Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2018-03-16soc/amd/stoneyridge: Create a HALT_THIS_AP calloutRichard Spiegel
It was required for all cores use the same CAR teardown function (exit_car.S and gcccar.inc). AGESA has already been modified to do the AP to do the call out. Create assembly code to call chipset_teardown_car and then enter an endless loop with halt instruction. Then create the call out that will call this new assembly code. BUG=b:70338633 AGESA COMMIT=3313d277 TEST=Created a debug version of AGESA that would print the returned status of HALT_THIS_AP. Build code without the fix, see the return. Build code with the fix, see that there's no return. Change-Id: I05ee405812211d93dfdbdc5ee7d9978c2eb585e1 Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com> Reviewed-on: https://review.coreboot.org/24999 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Martin Roth <martinroth@google.com>
2018-03-16stoneyridge: Update AGESA binary and AGESA.hRichard Spiegel
AGESA.bin was updated in the binary repo, so update the submodule pointer. Among other changes, this added a callback "AGESA_HALT_THIS_AP", which requires updated header files. BUG=b:70338633 TEST=build kahlee. Change-Id: I5a07f1c539d00aed34cfe45d6d7ef60c1dc56566 Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com> Reviewed-on: https://review.coreboot.org/25183 Reviewed-by: Martin Roth <martinroth@google.com> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2018-03-16soc/amd/stoneyridge/southbridge.c: Create AOAC initialization codeRichard Spiegel
Devices that need to have their AOAC register enabled do have a delay before they become available. Currently each device has their own wait loop. Create a procedure that initializes all AOAC devices in a table and wait for all AOAC to become alive, then call this new procedure before the call to initialize the UART. Then change all procedures that initialize some AOAC by moving the devices to the table and removing AOAC initialization code. BUG=b:74416098 TEST=Build and boot kahlee checking that UART is sending debug messages out. Change-Id: I359791c2a332629aa991f2f17a67e94726a21eb5 Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com> Reviewed-on: https://review.coreboot.org/25142 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Martin Roth <martinroth@google.com>
2018-03-16soc/intel/apollolake: Add config option for enabling hotplugFurquan Shaikh
PcieRpHotPlug in apollolake UPD is default enabled. This change adds a config option to enable hotplug only if explicitly requested by mainboard. This changes the default behavior on all apollolake boards to have hotplug disabled. BUG=b:74633273 BRANCH=reef,coral Change-Id: I572c054d31aaf5d43a79c4b1773ec9356da48d9d Signed-off-by: Furquan Shaikh <furquan@google.com> Reviewed-on: https://review.coreboot.org/25187 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2018-03-16soc/intel/apollolake and mainboards: Use pcie_rp_clkreq_pin arrayFurquan Shaikh
This change uses an array pcie_rp_clkreq_pin for accepting CLKREQ# from mainboards instead of defining a separate property for each root port. This allows us to use memcpy to copy the entire array into FSP params as well as new properties for PCIe root ports can be added as arrays in future CLs. BUG=b:74633273 BRANCH=reef,coral Change-Id: Ifa05f1e38fcfd95063ec327712e472cdbd12dbb7 Signed-off-by: Furquan Shaikh <furquan@google.com> Reviewed-on: https://review.coreboot.org/25186 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2018-03-16mb/google/eve: Update DPTF parametersDuncan Laurie
1) Set the critical temperature threshold to 100C to match changes on other boards. This is intended to reduce DPTF-initiated thermal shutdowns before it has had a chance to react. 2) Reduce the CPU passive threshold sample rate from 5 seconds to 1 second so DPTF will react faster to rapid temperature increases. BUG=b:67459049 BRANCH=eve TEST=manual performance/power testing on Eve hardware Change-Id: Ib660dcb25422fea0aa692fac5ba65b49808965ba Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: https://review.coreboot.org/25153 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2018-03-16security/tpm: Fix TPM software stack vulnerabilityzaolin
* Fix tlcl_read() for TPM 1.2 * https://github.com/nccgroup/TPMGenie Change-Id: I1618b2cc579d189bccca7a781e2bed0976a8b471 Signed-off-by: zaolin <zaolin@das-labor.org> Reviewed-on: https://review.coreboot.org/25184 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2018-03-15mb/google/poppy/variants/nami: Add gpio-keys ACPI node for PENHShelley Chen
Use gpio_keys driver to add ACPI node for pen eject event. Also setting gpio wake pin for wake events. BUG=b:73121017 BRANCH=None TEST=./util/abuild/abuild -p none -t google/poppy -x -a Change-Id: I5d87d938ac3a4e52e676850b9d8b80e83726275d Signed-off-by: Shelley Chen <shchen@chromium.org> Reviewed-on: https://review.coreboot.org/25162 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2018-03-15mb/google/poppy/variants/nami: Use GPP_B4 as Touchscreen Power EnableShelley Chen
Touchscreen power enable for Nami has moved from GBB_C22 to GPP_B4 in the latest schematics. BUG=b:74347464 BRANCH=None TEST=./util/abuild/abuild -p none -t google/poppy -x -a Change-Id: I3b1794d44f25c0d42d082d63b9e3ec3dfcef7528 Signed-off-by: Shelley Chen <shchen@chromium.org> Reviewed-on: https://review.coreboot.org/25154 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Furquan Shaikh <furquan@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2018-03-15soc/amd/stoneyridge: Call sb_acpi_mmio_decode()Garrett Kirkendall
Call function sb_acpi_mmio_decode() from bootblock_fch_early_init(). This enables decoding of the FCH ACPI MMIO regions 0xfed80000 - 0xfed81fff. This is another step to moving AGESA out of the bootblock for StoneyRidge BUG=b:74586747 BRANCH=master TEST=Build and boot on Grunt. Change-Id: I8cf329e5cd2002b225742fefa5c1ddd2598de674 Signed-off-by: Garrett Kirkendall <garrett.kirkendall@amd.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/25161 Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Martin Roth <martinroth@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2018-03-15include/device: Add pci id for Intel EMMC for SKLBarnali Sarkar
Change-Id: I18315e48653b16b34d1473e6c0bb2a2662a1a2c3 Signed-off-by: Barnali Sarkar <barnali.sarkar@intel.com> Reviewed-on: https://review.coreboot.org/23870 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Subrata Banik <subrata.banik@intel.com> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2018-03-15soc/intel/broadwell: add support for Intel GMA OpRegionMatt DeVillier
Add global/ACPI nvs variables required for IGD OpRegion. Add functions necessary to generate ACPI OpRegion, save the table address in ASLB, and restore table address upon S3 resume. Implementation largely based on existing Haswell/Lynxpoint code. Test: boot Windows 10 on google/lulu with Tianocore payload and GOP display init, observe display driver loaded and functional, display not black screen when resuming from S3 suspend. Change-Id: I024f4f0784df3cbbb9977692e9ef0ff9c3552725 Signed-off-by: CoolStar <coolstarorganization@gmail.com> Signed-off-by: Matt DeVillier <matt.devillier@gmail.com> Reviewed-on: https://review.coreboot.org/25094 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Patrick Rudolph <siro@das-labor.org>
2018-03-15mb/google/octopus: Enable audio components.Shamile Khan
Octopus uses MAX98357A speaker amplifier and DA7219 codec. Add device tree entries and Kconfig settings for these components. BUG=b:73292699,b:73230879 BRANCH=None TEST=Build coreboot for Octopus board. Change-Id: I27b5113677a8bd44dbbae587e27616d9e0b90d7f Signed-off-by: Shamile Khan <shamile.khan@intel.com> Reviewed-on: https://review.coreboot.org/25117 Reviewed-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Furquan Shaikh <furquan@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2018-03-14mb/google/poppy/variants/baseboard: Add gpio-keys ACPI node for PENHNicolas Boichat
This change uses gpio_keys driver to add ACPI node for pen eject event. BUG=b:74413116 TEST=Verified using evtest that pen eject event results in events as expected. Change-Id: I6019d633f4337137bb9fbba770040cb5b30da773 Signed-off-by: Nicolas Boichat <drinkcat@chromium.org> Reviewed-on: https://review.coreboot.org/25147 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2018-03-14soc/intel/cannonlake: Disable RTC write protectCaveh Jalali
The cannonlake FSP enables PchLockDownRtcMemoryLock by default, but we need this memory to be writable. We normally over-ride this in the SoC chip init code, so we'll do the same on cannonlake. BUG=b:71722386 BRANCH=none TEST=Filled /dev/nvram with 0xff and 0x00 bytes to verify we can flip all the bits. Change-Id: I7cdd4abc2b3795d7dd82236fbe3c112428ee882b Signed-off-by: Caveh Jalali <caveh@chromium.org> Reviewed-on: https://review.coreboot.org/25069 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
2018-03-14mb/google/zoombini/variants/meowth: Make FPMCU interrupt level-triggeredVincent Palatin
Fix the IRQ configuration: it must be level-sensitive not edge-sensitive (and match the GPIO configuration). BUG=b:71986991 BRANCH=none TEST=on Meowth, /proc/interrupts shows 'IO-APIC 46-fasteoi chromeos-ec' then run 'ectool --name=cros_fp fpmode fingerup' and see the number of interrupts incrementing and the MKBP event happening. Change-Id: Iba8cff21d637fe6bf4ef5152fc01aaf98906477d Signed-off-by: Vincent Palatin <vpalatin@chromium.org> Reviewed-on: https://review.coreboot.org/25110 Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Furquan Shaikh <furquan@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2018-03-14mainboard/google/meowth: Enable System Agent dynamic frequencyLijian Zhao
Enable System Agent dynamic frequency support by default. BUG=None TEST=Build and flash with debug version FSP, check SaGv in serial print to be set to "4". Change-Id: I7dd29db206b06e600407bb0b1d0bc7530f4ac93e Signed-off-by: Lijian Zhao <lijian.zhao@intel.com> Reviewed-on: https://review.coreboot.org/25093 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Nick Vaccaro <nvaccaro@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2018-03-14soc/intel/cannonlake: Add SaGv value definitionLijian Zhao
SaGv(Sytem Agent Dynamic Frequency) have four settings, disabled, disabled but running at fixed lower frequency, disabled but running at fixed middle frquency, disabled but running at fixed high frequency and totally enabled. BUG=None. Change-Id: Ib5fb648179e7889aaa64d91e6cf7a7a7503f4225 Signed-off-by: Lijian Zhao <lijian.zhao@intel.com> Reviewed-on: https://review.coreboot.org/25116 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2018-03-14src/device/dram/ddr2: Fix supported burst lengthsElyes HAOUAS
Supported burst lengths are described at byte 16 Change-Id: I502710bdac7eec715b29febefd64be88e5a1b80a Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/25098 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
2018-03-14soc/amd/stoneyridge: Configure FCH for TPMGarrett Kirkendall
In preparation for moving AGESA calls out of the bootblock: * Add sb_tpm_decode to enable FCH decoding of TPM 1.2 regions and Legacy TPM IO 0x7f-0x7e and 0xef-0xee * Modify sb_tpm_decode_spi to additionally call sb_tpm_decode. BUG=b:65442212 BRANCH=master TEST=abuild, build Gardenia, build and boot Grunt (with other changes to call code not committed at this time) Change-Id: I0e2399e113c765393209dd11fd835fc758cf3029 Signed-off-by: Garrett Kirkendall <garrett.kirkendall@amd.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/25027 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
2018-03-14soc/intel/baytrail: add support for Intel GMA OpRegionMatt DeVillier
Add global/ACPI nvs variables required for IGD OpRegion. Add functions necessary to generate ACPI OpRegion, save the table address in ASLB, and restore table address upon S3 resume. Implementation largely based on existing Broadwell code. Test: boot Windows 10 on google/squawks with Tianocore payload and GOP display init, observe display driver loaded and functional, display not black screen when resuming from S3 suspend. Change-Id: Iab15e1de2bb7d8fbec2e8705a621cfca0f255d4b Signed-off-by: Matt DeVillier <matt.devillier@gmail.com> Reviewed-on: https://review.coreboot.org/25102 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Patrick Rudolph <siro@das-labor.org>
2018-03-14drivers/intel/gma: fix opregion SCI register for Atom platformsMatt DeVillier
Most Intel platforms use separate registers for software-based SMI (0xe0) and SCI (0xe8), but Atom-based platforms use a single combined register (0xe0) for both. Adjust opregion implementation to use the correct register for Atom-based platforms. Test: Boot Windows on Atom-based ChromeOS device with Tianocore payload and non-VBIOS graphics init; observe Intel display driver loaded correctly and internal display not blank. (requires additional change for Atom platforms to select CONFIG_INTEL_GMA_SWSMISCI) Change-Id: I636986226ff951dae637dca5bc3ad0e023d94243 Signed-off-by: Matt DeVillier <matt.devillier@gmail.com> Reviewed-on: https://review.coreboot.org/23696 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Patrick Rudolph <siro@das-labor.org>
2018-03-14acpi: update comment referencing ACPI IDJoel Kitching
ACPI ID for coreboot is now "BOOT" according to CL:18521. BUG=none BRANCH=master TEST=none Change-Id: I802ce284001b186f6cd8839b8c303d49f42b4d38 Signed-off-by: Joel Kitching <kitching@google.com> Reviewed-on: https://review.coreboot.org/25042 Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2018-03-13mb/google/octopus: Add yorp variantJustin TerAvest
This creates a yorp variant for octopus; nothing too interesting now, just picks up values from the baseboard. BUG=b:74443669,b:74067452 TEST=Build Change-Id: I55af8f02d33138a3b6bab7860a665e3deb5595c2 Signed-off-by: Justin TerAvest <teravest@chromium.org> Reviewed-on: https://review.coreboot.org/25086 Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2018-03-13mb/google/poppy/variants/nautilus: Enable SAR configsFurquan Shaikh
This change enables SAR configs when building with CHROMEOS option. BUG=b:74439919 Change-Id: I11a8fa04a77f688ed288780f2c605b8ac701f5a9 Signed-off-by: Furquan Shaikh <furquan@google.com> Reviewed-on: https://review.coreboot.org/25104 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2018-03-13mb/google/poppy/variants/nami: Use internal pulldown for MEM_CONFIG_4Furquan Shaikh
Since nami proto did not have any external pull on MEM_CONFIG_4, use a weak internal pull down before reading it. BUG=b:74420123 TEST=Verified that the value read for MEM_CONFIG_4 is correct on nami. Change-Id: I45989d2ca35b863f391baba9e2f2e602033217d4 Signed-off-by: Furquan Shaikh <furquan@google.com> Reviewed-on: https://review.coreboot.org/25103 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2018-03-12mb/google/octopus: Fix lpddr4 skusJustin TerAvest
The current lpddr4 skus entries do not match the RAMID table in the schematic. This commit updates that so they are consistent. Thankfully, the values are the same as for glkrvp, so I just copied from there. BUG=b:74392818 TEST=None Change-Id: I2e63ea0b27ef58038e5a37949c31a808989c98c2 Signed-off-by: Justin TerAvest <teravest@chromium.org> Reviewed-on: https://review.coreboot.org/25063 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2018-03-12mb/google/zoombini/variants/meowth: change gpios to no-connectsNick Vaccaro
The following gpios are no longer needed and are now configured as no-connects : GPP_C6, GPP_H4, GPP_H5 BUG=b:74406599 BRANCH=master TEST=none Change-Id: I55769336195db0e57dfbaf5b5770e15050138341 Signed-off-by: Nick Vaccaro <nvaccaro@google.com> Reviewed-on: https://review.coreboot.org/25070 Reviewed-by: Furquan Shaikh <furquan@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2018-03-12mb/google/poppy: Clear memory_params before initializing themNicolas Boichat
Make sure that fields that are not updated in variant_memory_params keep a default value of 0. In particular, use_sec_spd is intended to have a default value of 0 on all platforms. Without this patch, a random value is used and all boards (except nami) get stuck on boot. BRANCH=poppy BUG=b:74439917 TEST=Nautilus and poppy can boot, and do not get stuck at "CBFS: 'sec-spd.bin' not found." Change-Id: I06c6511625de930903ae13788bdcd27667a17886 Signed-off-by: Nicolas Boichat <drinkcat@chromium.org> Reviewed-on: https://review.coreboot.org/25101 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Furquan Shaikh <furquan@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2018-03-10meowth: Add SAR Sensor in devicetreeGwendal Grignou
Add left and right semtech SAR sensor. BUG=b:74363445 TEST=Test on meowth, alongside 24962. Check in sysfs that SX9310 is presented: /sys/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/device:09/SX9310:00 /sys/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/device:0d/SX9310:01 Change-Id: I017db1105800003b312e75dc7e1e27be535a457a Signed-off-by: Gwendal Grignou <gwendal@chromium.org> Reviewed-on: https://review.coreboot.org/25062 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
2018-03-09mb/google/zoombini: re-enable software syncCaveh Jalali
we had disabled software sync for bringup - we now have enough functionality in place to turn on software sync. Change-Id: Ib7f5a24ed8a47cb44b3f505e3cd49e0cb6931dc0 Signed-off-by: Caveh Jalali <caveh@google.com> Reviewed-on: https://review.coreboot.org/23630 Reviewed-by: Patrick Georgi <pgeorgi@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2018-03-09soc/intel/skylake: Move PCR DMI programming into bootblockSubrata Banik
As per PCH BWG 2.5.16, set up LPC IO Enables PCR[DMI] + 2774h bit [15:0] to the same value program in LPC PCI offset 82h. Also this cycle decoding is only allowed to set when SRLOCK is not set. Hence move the required programming from lpc.c to pch.c. Also only enable COM port ranges if CONFIG_DRIVERS_UART_8250IO Kconfig is selected. Change-Id: Ie706735492a450baa653d8a8bb74c6e42f5150b8 Signed-off-by: Subrata Banik <subrata.banik@intel.com> Reviewed-on: https://review.coreboot.org/23866 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2018-03-09soc/intel/common: Enable decoding of the COMB range to LPC based on KconfigSubrata Banik
By default all Intel platform has enable IO decode range for COMA if CONFIG_DRIVERS_UART_8250IO is selected. With this patch, COMB will get enable based on CONFIG_SOC_INTEL_COMMON_BLOCK_LPC_COMB_ENABLE Kconfig selection. Also make lpc_enable_fixed_io_ranges() function returns Enabled I/O bits to avoid an additional pci configuration read to get the same data. Change-Id: I884dbcc8a37cf8551001d0ca61910c986b903ebc Signed-off-by: Subrata Banik <subrata.banik@intel.com> Reviewed-on: https://review.coreboot.org/25045 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
2018-03-09mb/google/poppy/variants/nami: Fix typo in nami MakefileFurquan Shaikh
Change SECONDARY_SPD_SOURCES to SEC_SPD_SOURCES as that is what the spd target expects. TEST=Verified that sec-spd.bin is present in coreboot.rom Change-Id: I4299df1eb9009095ef899c5b83823750dfc715d8 Signed-off-by: Furquan Shaikh <furquan@google.com> Reviewed-on: https://review.coreboot.org/25083 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2018-03-09Timestamps: Add option to print timestamps to debug consoleMartin Roth
Prints the timestamp name and value to the debug console if enabled in Kconfig. Change-Id: Ie6e6a4877fefec45fb987ceae7d42de6ce768159 Signed-off-by: Martin Roth <martinroth@chromium.org> Reviewed-on: https://review.coreboot.org/25024 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
2018-03-09soc/amd/stoneyridge: Add function to enable I2C host controllersGarrett Kirkendall
In preparation for moving AGESA calls out of bootblock: Add function to enable the four stoneyridge I2C engines. BUG=b:65442212 BRANCH=master TEST=abuild, build Gardenia, build and boot Grunt (with other changes to call code not committed at this time) Change-Id: Icb55c49cf56c65a9c2e1838cff1ed5afc04e1826 Signed-off-by: Garrett Kirkendall <garrett.kirkendall@amd.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/25026 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2018-03-09soc/amd/stoneyridge: Add ACPI MMIO enable functionGarrett Kirkendall
In preparation for moving AGESA calls out of bootblock: * Add definitions for needed registers in southbridge.h * Add function to enable AMD FCH ACPI MMIO regions 0xfed80000 to 0xfed81ffff. Will be called by a later commit. BUG=b:65442212 BRANCH=master TEST=abuild, build Gardenia, build boot Grunt (with other changes to call code not committed at this time) Change-Id: If26efa6c6f5b562ba898e7d9da4827833310dc26 Signed-off-by: Garrett Kirkendall <garrett.kirkendall@amd.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/25025 Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com> Reviewed-by: Martin Roth <martinroth@google.com> Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2018-03-09soc/intel/denverton_ns: Update UART legacy mode to keep FSP tracesJulien Viard de Galbert
The FSP can only output its traces when the HSUART PCI device is available. - Move the hiding to after last FSP call. - Adapt coreboot PCI enumeration to keep the legacy configuration. With UART configured as legacy Linux will not re-enumerate it but detects it as legacy (ttyS0 instead of ttyS4). Change-Id: Id8801e178ffd8eeee78ece07da7bd6b8dbd88538 Signed-off-by: Julien Viard de Galbert <jviarddegalbert@online.net> Reviewed-on: https://review.coreboot.org/23623 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Nico Huber <nico.h@gmx.de>
2018-03-09mainboard/google/kahlee: Set GPIO 40 to inputMartin Roth
GPIO 40 isn't currently being used, so set it to be an input. BUG=b:73387647 TEST=Build & boot grunt Change-Id: I5a04cbab1276cd20e7f9c7576e8111089dd2b155 Signed-off-by: Martin Roth <martinroth@chromium.org> Reviewed-on: https://review.coreboot.org/25016 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2018-03-09mainboard/google/kahlee: Disable Bayhub part on board_id 0Martin Roth
The Bayhub part is not used on proto with board_id 0, so disable it. BUG=b:74248569 TEST=Build & boot Grunt. Bayhub part is disabled. Change-Id: I635356d41bab637726594d403d66dde730f12256 Signed-off-by: Martin Roth <martinroth@chromium.org> Reviewed-on: https://review.coreboot.org/25015 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Justin TerAvest <teravest@chromium.org>
2018-03-09ec/google/chromeec: Add boardid.c to bootblockMartin Roth
Update build so that we can get the board ID in bootblock. BUG=b:74248569 TEST=build and boot grunt with follow-on patch. Bayhub part is disabled. Change-Id: I6353bcb4abcef4e8dc2b625082e33b73525c8525 Signed-off-by: Martin Roth <martinroth@chromium.org> Reviewed-on: https://review.coreboot.org/25014 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2018-03-09cpu/x86/mp_init: Print amount of time it takes in bsp_do_flight_planFurquan Shaikh
Since the timeout in bsp_do_flight_plan is bumped up to 1 second, this change adds a print to indicate the amount of time it takes for all the APs to check-in. TEST=Verified on Nami that it prints: "bsp_do_flight_plan done after 395 msecs." Change-Id: I4c8380e94305ed58453ed18b341b3b923949d7a8 Signed-off-by: Furquan Shaikh <furquan@google.com> Reviewed-on: https://review.coreboot.org/25044 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Patrick Georgi <pgeorgi@google.com> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2018-03-08mb/google/poppy/variants/nami: Define smbios_mainboard_sku to return SKU IDsShelley Chen
Return proper SKU IDs so that mosys can return the proper variant. BUG=b:74059798 BRANCH=None TEST=./util/abuild/abuild -p none -t google/poppy -x -a Change-Id: I665fa491de6e277fea5cc071b1f04a21317bccba Signed-off-by: Shelley Chen <shchen@chromium.org> Reviewed-on: https://review.coreboot.org/25028 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2018-03-08nb/intel/haswell;sb/intel/lynxpoint: Enable VT-d and X2APICMatt DeVillier
We use the usual static addresses 0xfed90000/0xfed91000 for the GFX IOMMU and the general IOMMU respectively. These addresses have to be configured in MCHBAR registers and reserved from the OS. GFXVTBAR/VTVC0BAR policy registers set to be consistent with proprietary vendor firmwares on hardware of same platform (2 different vendor firmwares compared, found to be identical). Change-Id: Ib8f2fed9ae08491779e76f7d1ddc1bd3eed45ac7 Signed-off-by: Matt DeVillier <matt.devillier@gmail.com> Reviewed-on: https://review.coreboot.org/24983 Reviewed-by: Youness Alaoui <snifikino@gmail.com> Reviewed-by: Nico Huber <nico.h@gmx.de> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
generated by cgit v1.2.3 (git 2.39.1) at 2024-07-18 19:19:17 +0000