Age | Commit message (Collapse) | Author |
|
The flag FF_FreezeDis marks if this feature is disabled. For a better
readability rename freeze_mode to freeze_disable and invert the meaning
of this information.
Change-Id: I648b2392d2c8046965479511fde485a9cb934378
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/20432
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
The two flags FF_FanReq and FF_Freeze_Dis should be treated as
8 bit values and not as 32 bit. Change the length of these fields to
1 byte and adjust the offset and mask for FF_FanReq.
Change-Id: If5e9e8b16491a33997cc39c3dd9b80f97682adc6
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/20431
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
This patch basically does two things -
1) Remove unnecessary setting of flex_ratio to TDP nominal:
Factory configured (default) Max Non-TURBO ratio(P1) is already cofigured
in MSR_PLATFORM_INFO(0xCE).
If this Maximum Non-TURBO Ratio(P1) needs to be modified, it should be done
using MSR_FLEX_RATIO (0x194).
Here, in this code, the FLEX_RATIO is being modified by the TDP Nominal
Ratio, reading the MSR_CONFIG_TDP_NOMINAL(0x648). But this value is
actually less than the factory configured Maximum Non TURBO Ratio (P1).
So, this code is actually not required.
Also, the Bit 12 in PCH Soft Strap Register is already set in descriptor.
This Bit implies Processor Boot Max Frequency -
0 = Disable Boot Max Frequency
1 = Enable Boot Max Frequency (Default)
This setting determines if the processor will operate at maximum frequency
at power-on and boot.
Thus this patch will avoid one extra platform warm reset now onwards.
2) Remove wrongly setting Max Frequency in Bootblock phase:
In the function set_max_frequency(), the P-State max ratio was set to
TDP Nominal ratio if C-TDP was enabled, else it was set to Max Non
Trbo ratio.
But, when the cpu gets reset, it will operate with the Max-Non Turbo
ratio only, which is greater than the TDP Nominal ratio.
So, no need to set back the ratio to TDP Nominal which is lower than
the currently operating frequency.
BUG=none
BRANCH=none
TEST=Build and boot poppy
Change-Id: I24bfc86ddf0f038d85da938e41e950382fe2a6c3
Signed-off-by: Barnali Sarkar <barnali.sarkar@intel.com>
Reviewed-on: https://review.coreboot.org/20050
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Use the new PAD_CFG_GPI_INT macro to specify the headset codec
interrupt as specifically edge triggered (since it is registered
as EDGE_BOTH in the devicetree) in order to prevent the interrupt
from firing unexpectedly when the system is resuming.
Also change the DSP interrupt to edge triggered since the kernel
is registering with IRQF_TRIGGER_RISING in order to prevent an
interrupt storm when it asserts.
BUG=b:35582164
TEST=manual testing on Eve:
1) ensure the headset codec sends interrupt on insert and remove
2) ensure there is only one interrupt counted when DSP asserts irq
Change-Id: I40a8ee667de653e4e70770cd96b6417442c1b0ec
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/20433
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Make this pin a GPI as it is supposed to be an input from the touch
controller and not driven by the AP.
BUG=b:35581264
TEST=check pin state with a scope
Change-Id: Ife5f84fcc614255b20e44389279d515a12f5751d
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/20430
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Board changes in rev6+ have a fix to VDDQ that should fix the issue
that was being seen with this SKU, so only lower the memory speed on
older boards.
BUG=b:37172778
TEST=memory stress testing on rev6 boards
Change-Id: I6d6fe730cabd74af23eab3f02feef9da01a35fd4
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/20429
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Add support for waking from and logging device events that
originate in the Embedded Controller. As this device uses
Deep S3 it relies on the EC to wake the AP from the trackpad
and DSP wake sources.
BUG=b:30624430
TEST=manual testing on Eve: wake from Deep S3 via trackpad and
DSP and verify the event log contains the expected device event.
Change-Id: I0d6a9c5bfd4cea85e13446ffaa6fe3dab0db96a2
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/20428
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Add support for the new EC device event interface which is used to
report events from devices that are connected behind the EC.
This can be used to differentiate wake sources from the EC in the case
that the EC has the wake pins from various devices.
This can be used in case the AP is unable to directly wake from the
device itself, for example when using the Deep S3 state on Intel
platforms only a few pins can directly wake the AP.
BUG=b:30624430
TEST=build google/* boards that use chrome EC. Feature is used and
tested further in a subsequent commit.
Change-Id: I5126c6d6ffb6b0ef6e8db8dcd5aec62db925a371
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/20426
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Replace the unused "thermal overload" event with the new
"device event" and define the first few device events that are
supported by the Chromium EC.
BUG=b:30624430
TEST=build for google/* mainboards
Change-Id: I1f3aeedb87c2aad29a0a67b5c50c29a6961fb45f
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/20427
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Update this header from the upstream source so new host
commands can be used in coreboot.
https://chromium.googlesource.com/chromiumos/platform/ec
commit bbb759ceaa843f548f90c35d1668e17c8879bad3
BUG=b:30624430
TEST=build google/* and intel* boards
Change-Id: I56c9f891262d8984b6a9a69d96752c2dd6bb2371
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/20425
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
The Chrome EC event for "thermal overload" was never implemented and
is being repurposed as the EC event mask is out of free bits.
Remove this from the boards that were enabling it.
BUG=b:36024430
TEST=build coreboot for affected boards
Change-Id: I6038389ad73cef8a57aec5041bbb9dea98ed2b6e
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/20424
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
The architecture is determined by __riscv__ in the LZ4_copy8 function
(located in src / commonlib / lz4_wrapper.c). __riscv exists in gcc7.1.1.
But __riscv__ does not exist.
Change-Id: I38fd41da9afd76c254f0c3d6984579c3790e5792
Signed-off-by: XiangWang <wxjstz@126.com>
Reviewed-on: https://review.coreboot.org/20125
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Andrew Waterman <aswaterman@gmail.com>
Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
|
|
DISPPLANE_BGRX888 defined in drivers/intel/gma/i915_reg.h
included in i915.h file
Change-Id: I4e9414f39a29e4eac7e325672ce6520a5654d3bc
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/20409
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Change-Id: Ic01bbae9acaabaade777db52825aa80d25fc5961
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/20410
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
Set RX6110SA RTC backup mode to primary cell. This mode reduces the
backup current consumption of the RTC.
Change-Id: I7c0c26a0ed5d8f48587acc917f8bb1c5c2b8869a
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/20414
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
The used RTC6110SA has issues to enter backup mode when the power supply
decreases too slow when the mainboard is turned off. Switch to backup
mode "primary cell" to make sure backup mode will be entered correctly
on power-off. In addition set IOCUTEN to minimize the backup current
consumption of the RTC.
Change-Id: I9733aa9f2981a25f6d42279eff0c4980e5eb5a5a
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/20413
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
According to the datasheet the RTC needs a power rising slope of no more
than 100µs/V to ensure a correct power-on reset. If the mainboard that
hosts the RTC cannot guarantee this, a software reset sequence is needed
in the case where the battery was drained completely.
As the rising slope of the power supply depends on so many parameters
and is highly mainboard specific, refactor the initialization code to
perform a software reset every time a power loss event is recognized by
the RTC.
Change-Id: If64d672e51667523058041bd00e1e50ac047143d
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/20412
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Change-Id: I8fabb7331435eb518a5c95cb29c4ff5ca98560d2
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/20349
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Use the plain address instead of the weird shifted encoding (e.g. if
we'd use `0xa0` as address, it's actually `0x50` encoded into a write
command).
Change-Id: I6febb2e04e1c6de4294dfa37bde16b147a80b7a8
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/20405
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
There is no choice, if not leaving it with the default the build
will fail.
Change-Id: Id91e3ce87f8ced3001fcd2125f8f6781b270f5bc
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/20402
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Cannonlake has built-in UART driver as part of LPSS block. However port
mapped decoders are in use as well.
Change-Id: I9f209bf29c1748c5beea31bc6b31cb07a1e14195
Signed-off-by: Andrey Petrov <andrey.petrov@intel.com>
Reviewed-on: https://review.coreboot.org/20063
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
When the C compiler expects 16-byte alignment of the stack it is
at the call instruction. Correct existing call points from assembly
to ensure the stacks are aligned to 16 bytes at the call instruction.
Change-Id: Icadd7a1f9284e92aecd99c30cb2acb307823682c
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/20314
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Change-Id: Ic48401e92103ff0ec278fb69a3d304148a2d79aa
Signed-off-by: Hannah Williams <hannah.williams@intel.com>
Reviewed-on: https://review.coreboot.org/19759
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Add Cannon Lake SoC boilerplate directory with:
* SoC directory
* Base Kconfig
* Dummy cbmem.c
Change-Id: Ie28d8b56a1d1afcf1214ef734a08be6efcc8a931
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Signed-off-by: Andrey Petrov <andrey.petrov@intel.com>
Reviewed-on: https://review.coreboot.org/20061
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Use the TSC for the Stoney Ridge monotonic timer. Modern AMD
CPUs have invariant timestamp counters. This patch brings the
feature more in line with other devices and allows the use of
typical monotonic timer functions.
BUG=chrome-os-partner:62578062
Change-Id: I07b05fbc7cdea54a45daac01954284a9fd67e42f
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/20201
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
There are up to two on-board PCI devices where bus master has to be
enabled in PCI config space. As there is no need for a complete PCI
driver for these devices just set the bus master bit in
mainboard_final().
In a perfect world that would be the task of the runtime driver which
unfortunately don't do that.
Change-Id: Ic2896d5e7568a455737af26b14b2c398caae5f72
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/20403
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
The ALSB gnvs variable is used to load the OpRegion memory
address into the ASLS register on the S3 resume path, and must
therefore first be set on the normal boot path.
This patch brings Haswell in line with SNB/IVB/Nehalem, which
already save the OpRegion address in ASLB.
Change-Id: Ie062cbfe7e7f60c2a4e2b9111f6b6da87ced7a39
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/20254
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
Now that pci_devs.h is part of soc/ and not used for multiple
southbridges:
* Remove devices not present in the Stoney Ridge APU
* Complete the list to include additional devices besides
those in the FCH.
BUG=chrome-os-partner:62578372
Change-Id: I1cd2d5e41473f362bbfd28ee93788a292bc33991
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/20370
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Update pci_devs.h to the correct IDs for Stoney Ridge.
BUG=chrome-os-partner:62578372
Change-Id: Ic1a7fe8d95c34b80e21cc089168732372d9690a3
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/20200
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Add definitions for the P-state 0 MSR and Core Performance Boost
Control.
BUG=chrome-os-partner:62578062
Change-Id: I0c16dde17f1be41a3310c3ccefe3936aba0e8ec0
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/20199
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Add a memmap file with a cbmem_top() function. Remove the
LATE_CBMEM_INIT, allowing the default of EARLY. Remove calls
to the late-only set_top_of_ram() function.
Change-Id: I11ad7190031c912642a7312f2fc6f792866288b7
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/19751
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Change-Id: I6ede71ec660678bb5f77693a9095aa0f198e4e26
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/19752
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Change-Id: Ic2cdfa08cdae9f698eb2f8fa4c4ae061f1a7d903
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/20340
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
|
|
Some of these can be changed from #if to if(), but that will happen
in a follow-on commmit.
Change-Id: I66cde1adcf373889b03f144793c0b4f46d21ca31
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/20338
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Some of these can be changed from #if to if(), but that will happen
in a follow-on commmit.
Change-Id: I82bf68a7ee54ff88f65aacc9eb0dbc30d013aae0
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/20337
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Some of these can be changed from #if to if(), but that will happen
in a follow-on commmit.
Change-Id: Ie685bbbb1cbf06d32631ea40ad120b6f45374b2e
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/20336
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Some of these can be changed from #if to if(), but that will happen
in a follow-on commmit.
Change-Id: I9f4155285529ec28e826637a61436478f648704c
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/20335
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
- Describe RT5663 headphone codec in ACPI so it can
be enumerated by the OS.
- Supply NHLT binaries for RT5663
BUG=b:62872377
TEST=Apply full patch set and UCM, verify basic audio works.
Signed-off-by: Kevin Cheng <kevin.cheng@intel.com>
Change-Id: I5bbd58b0e660cdf5089e6a6dd35a757ecf8ec076
Reviewed-on: https://review.coreboot.org/20305
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Problem was introduced by fb2f667da2 "nb/amd/amdk8: Link raminit_f.c"
which linked debug.c and was not tested with this option.
Change-Id: I8597a6915c65ea783a864110cb23ecb34ea0611b
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/19653
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Swift Geek <swiftgeek@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Needed to generate cpu entries.
Change-Id: Ia3f5137c7642bb9f79562cc9d6e6881aca749179
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/19496
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Change-Id: I56cb941d07ac48f8209a892ec18af8f5090765f7
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/20399
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Change-Id: Id46c0b57bd7c9b954b29537c70254df947690e0b
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/20397
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
In the code we do the following in a number of places
to pre-initialize an array with a certain value before
overwriting some of the array with other values:
u8 mainboard_picr_data[FCH_INT_TABLE_SIZE] = {
[0 ... FCH_INT_TABLE_SIZE-1] = 0x1F,
}
clang does not like that behavior unless we specify
the option -Wno-initializer-overrides.
Remove the check for gcc in those places, too, because
1) it would silently change array contents between compilers
2) the check isn't sufficient to determine compilation on
clang vs gcc
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Change-Id: I93cc121b6fec099fcdbd5fd1114c2ff7cbc291dc
Reviewed-on: https://review.coreboot.org/20384
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Wow, this one is disliked by clang for the empty for() loop, but
looking at the file just makes my eyes bleed a little bit. I remember
the circumstances under which we let this code go in. It was supposed
to save contributions from a vendor, but that never worked out.
Just to keep the little chunks down, here's an indent run and some of
the cruft removed that doesn't actually contribute to functionality in
any way.
Change-Id: Ie82166ca82f09c4b66decfde5ad194a2d70b0708
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-on: https://review.coreboot.org/20386
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Fix CID 1376472 detected by coverity. Zero extend the capacity instead
of sign extending it.
TEST=Build and run on reef
Change-Id: I6aac422fb1dacb75e0cc44a94ff1f467ce9f529e
Signed-off-by: Lee Leahy <Leroy.P.Leahy@intel.com>
Reviewed-on: https://review.coreboot.org/20392
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
|
|
Add a SMM_TSEG_SIZE symbol that can be used in top of memory
calculations.
Change-Id: I26f3b06f85f0cf5613656c1d5df55bd9ea4bbbbc
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/19750
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Remove IDE from the Stoney Ridge source. This APU doesn't have
an IDE controller. The support was left over from pi/hudson.
BUG=chrome-os-partner:62580062
Change-Id: I7316c113a7464089ccfbea6b6cf69787940b9e97
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/20320
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Remove the pcie.c file. Historically PCIe lanes have been
available from the Gfx and/or the FCH. The integrated FCH in
this APU has no PCIe available.
BUG=chrome-os-partner:62580062
Change-Id: Ie89383dadfaa57c5a6d185e74551ae50ac8d9778
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/20319
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
The Stoney Ridge does not contain this bridge like some of the older
Hudson FCHs. Remove this support from the source.
This moves the Stoney Ridge IRQ setup to the southbridge file, hudson.c.
BUG=chrome-os-partner:62580062
Change-Id: I8f974ba76b8c20f4335dd8872eaf4b8172188ee2
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/20198
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Correct the majority of reported errors and mark most of the
remaining ones as todo. Some of the lines requiring a >80
break are indented too much currently.
Changes to agesawrapper.c cause the build to change, so this
file is also left as-is. Make hex values consistently lower-case.
BUG=chrome-os-partner:622407746
Change-Id: I0464f0cafac4ee67edc95d377dcf7aab9a90c66b
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/20249
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Correct the majority of reported errors and mark most of the
remaining ones as todo. (Some of the lines requiring a >80
break are indented too much currently.) Some of the alignment
in hudson.h still causes checkpatch errors, but this is
intentionally left as-is.
Also make other misc. changes, e.g. consistency in lower-case
for hex values, using defined values, etc.
These changes were confirmed to cause no changes in a Gardenia
build. No other improvements were made, e.g. changing to helper
functions, or converting functions like __outbyte().
BUG=chrome-os-partner:622407746
Change-Id: I768884a4c4b9505e77f5d6bfde37797520878912
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/19986
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Update Psi2Threshold, IccMax, AcLoadline, DcLoadline
VR config settings as per board design.
BUG=b:62063434
BRANCH=none
TEST=Build and boot soraka.
Change-Id: I254bbb88b82ddf278f0ec71bc98873df1d5e0d27
Signed-off-by: Rajneesh Bhardwaj <rajneesh.bhardwaj@intel.com>
Signed-off-by: G Naveen <naveen.g@intel.com>
Reviewed-on: https://review.coreboot.org/20309
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Naresh Solanki <naresh.solanki@intel.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Soraka uses MPS2949 IMVP8 controller and does not need the VR
workaroud similar to Eve.
BUG=None
TEST=Build & boot on soraka. Ensure IMVP8 controller goes to low power
mode in S3 and S0ix by measuring power.
Change-Id: Ib98bb709ecc9e362a5cef437e7319e41f398a73b
Signed-off-by: Rajneesh Bhardwaj <rajneesh.bhardwaj@intel.com>
Reviewed-on: https://review.coreboot.org/20255
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Code checked manually
Change-Id: Idf86546ddda4fa2b4b96f0b703c03af9931c757d
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/20251
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Correct the checkpatch errors reported in the asl files and
make other stylistic modifications.
These changes were confirmed to cause no changes in a Gardenia
build.
BUG=chrome-os-partner:622407746
Change-Id: Id8b2620d161062c444e493325d83bb158705b76b
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/20248
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
|
|
This requires to also unify the calling convention for
AGESA functions from
AGESA_STATUS (*agesa_func)(UINT32 Func, UINT32 Data, VOID *ConfigPtr)
to
AGESA_STATUS (*agesa_func)(UINT32 Func, UINTN Data, VOID *ConfigPtr)
On systems running 32bit x86 code this will not make a difference as
UINTN is uintptr_t which is 32bit on these machines.
Change-Id: I095ec2273c18a9fda11712654e290ebc41b27bd9
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-on: https://review.coreboot.org/20380
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
Return CB_SUCCESS and CB_ERR instead of some integer.
Preparation to merge intel/soc and intel/nb opregion implementations.
Change-Id: Ib99fcfe347b98736979fc82ab3de48bfc6fc7dcd
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/20220
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Some of these can be changed from #if to if(), but that will happen
in a follow-on commmit.
Change-Id: Id5bc8b75b1fa372f31982b8636f1efa4975b61a5
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/20346
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
... even though the author of the code probably wished he was
working on a (much faster) broadwell system instead. Let's fix
the header guard to reflect the right SOC.
Noteworthy: clang detected that this was wrong.
Change-Id: I74c217c0471800f40c31a9ac38ba5396f82cd724
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-on: https://review.coreboot.org/20387
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
It's pretty obvious that the author did not want to use a logical
and (&&) here but an arithmetical and (&)
Change-Id: Ic1bece86986906b76308bbb46235c22418e27990
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-on: https://review.coreboot.org/20388
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
dual_node is never used in that function. And it is never set
correctly either, because the register f3xe8 is never actually
read either. Just remove the whole useless construct.
Change-Id: If316da89bceae6b162f20e4b632276db2d9ef423
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-on: https://review.coreboot.org/20385
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
The warning -Wstack-usage= doesn't seem to exist on clang, so trying
to disable it makes the compiler unhappy about non-existent pragmas.
Catching this on gcc is good enough, so let's disable it for the clang
case
Change-Id: Ia3716a83ba41743ac1dbe73e70abd170de30d7ab
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-on: https://review.coreboot.org/20383
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
src/vendorcode/amd/agesa/f15/Include/OptionMemoryInstall.h:3688:7: error:
suggest braces around initialization of subobject
Change-Id: Id086a64205dfffa2d1324993f4164508b57b6993
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-on: https://review.coreboot.org/20382
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Change-Id: Ibff31a9960a23f03facbb09e76d6a5d6fbfb5e94
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-on: https://review.coreboot.org/20381
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Change-Id: I8b02596b116c0b164e83e7b02449c547224a50a6
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Reviewed-on: https://review.coreboot.org/20330
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Change-Id: Ia76c391e04e1e11bd110764902b91ef4ed5e8490
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/20308
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
If SSE instructions are enabled in the build assume the SMM
modules are compiled with SSE instructions. As such enable
the SSE instructions in SMM mode by setting up the cr4 register.
In addition, provide a place to save and restore the SSE state
in both the relocation handler and permanent handler.
Change-Id: Ifa16876b57544919fde88fba5b8f18e4ca286841
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/20244
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Fill in acpi_name to return proper ACPI names.
To be used with SSDT generators.
The ACPI names have to match those already used in ASL code.
By providing the ACPI name it can be retrieved by the
acpi_device_name() method and doesn't need to be hardcoded in
SSDT generators any more.
HDEF is defined in sb/intel/bd82x6x/acpi/audio.asl.
LPCB is defined in sb/intel/bd82x6x/acpi/lpc.asl.
RP0* is defined in sb/intel/bd82x6x/acpi/pcie.asl.
SATA is defined in sb/intel/bd82x6x/acpi/sata.asl.
SBUS is defined in sb/intel/bd82x6x/acpi/smbus.asl.
EHC? is defined in sb/intel/bd82x6x/acpi/usb.asl.
XHC is defined in sb/intel/bd82x6x/acpi/usb.asl.
Change-Id: I08611b11c694ee5034bca11cb321915d5c73c2f6
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/20086
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Fill in acpi_name to return proper ACPI names. To be used with
SSDT generators.
The ACPI names have to match those already used in ASL code.
By providing the ACPI name it can be retrieved by the
acpi_device_name() method and doesn't need to be hardcoded in
SSDT generators any more.
GFX0 is used in drivers/intel/gma/acpi/pch.asl.
MCHC is used in nb/intel/sandybridge/acpi/hostbridge.asl.
Change-Id: I19526e334a9c5435fdb19419a671b86c5f6b2be9
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/20085
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
|
|
The ChromeEC board directories for auron and rambi have been removed
from the latest version of ChromeEC. Remove them here so the submodule
can be brought forward.
Change-Id: I763d03009f735d3f8aedbeb44788d03714c86102
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/20361
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
|
|
Update the world facing camera sensor to OV13858 and also
add delay of 5ms after xshutdown rising which indicates system
ready status.
BUG=b:38326541
BRANCH=none
TEST=Build and boot soraka. Dump and verify that the generated DSDT table
has the required entries. Verified that sensor probe is successfull.
Change-Id: I0cd535e6568f104ffaa1092a13667def646df0eb
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Reviewed-on: https://review.coreboot.org/20292
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Naresh Solanki <naresh.solanki@intel.com>
|
|
Add clock frequency property into _DSD ACPI object and set it
to 19.2MHz for camera sensors. Upstream camera kernel has added
a check for clock frequency in sensor probe function and without
this property sensor probe fails.
BUG=b:38326541
BRANCH=none
TEST=Build and boot poppy. Dump and verify that the generated DSDT table
has the required entries. Verified that sensor probe is successfull.
Change-Id: I147b3c932a33ae034868f7f9b616500d24ca71e3
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Reviewed-on: https://review.coreboot.org/20294
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Naresh Solanki <naresh.solanki@intel.com>
|
|
Zero the framebuffer structure so if it is not filled in (either if
no display is present or if there is an error) then it does not
provide garbage data to the payload.
This was noticed when booting a board without a display attached as
the payload wrote to the framebuffer at a random address.
With this change the payload can properly handle the case where a
display is not attached and not corrupt memory.
Change-Id: I8114d88496cd2a4f2e7f07f377fe76f3180a7f40
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/20367
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
|
|
In the D0 and D3 ACPI methods use word access to the PME status and
control register. This brings the code inline with the Intel reference
code and matches how the kernel handles access to this register.
BUG=b:35587084
BRANCH=eve
TEST=manual stress testing of D0<>D3 transition across multiple devices
Change-Id: I53f7465d6ad5da1780a5641ff52056445ebaca8b
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/20364
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
For the skylake/kabylake generation of PCH there is an ACPI workaround
for emmc/sd power state that involves disabling and re-enabling dynamic
clock gating after enabling power to the controller, before setting the
power state to D0.
Under certain conditions we have observed that the controller is not
powered and ready by the time the kernel attempts to read the PME
control and status register and so the system will hang while attempting
to read PCI config register 0x84.
To ensure that the controller is ready add a 2ms delay after re-enabling
dynamic clock gating and before setting the power state to D0.
This issue has been observed on eMMC, but the same workaround exists for
the SD card interface so the same delay is added there.
BUG=b:35587084
BRANCH=eve
TEST=manual stress testing of D0<>D3 transition across many devices
shows no hard hang after 2 days.
Change-Id: If0f0323cf5437c54c907c332937b5de9dda2d8f6
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/20363
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Change-Id: Ifc6a0638c03fa5f3e1007a844e56dfa6f4c71d7e
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-on: https://review.coreboot.org/20326
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Most of these functions go unused most of the time, but in order
to not keep several copies around, let's make sure we are using
the same file everywhere first.
Change-Id: Ie121e67f3663410fd2860b7d619e8a679c57caba
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-on: https://review.coreboot.org/20325
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Code checked manually
Change-Id: I91ababb3bf7aa1ab0f71bb005c4685e81bb4d92f
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/20252
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Correct all checkpatch errors but leave two errors in place
that are caused by AMD typing.
Change-Id: I9daa374da76ff991de72d16bad0e8b586aa95525
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/20318
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Switch Garnenia mainboard to single soc/ directory structure.
Change-Id: I095804d603bcccf324d3244965081a9dccba62ae
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/19725
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Copy northbridge files from northbridge/amd/pi/00670F00
to soc/amd/stoneyridge and soc/amd/common.
Changes:
- update chip_ops and device_ops
- remove multi-node support
- clean up Kconfig and Makefile
Change-Id: Ie86b4d744900f23502068517ece5bcea6c128993
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/19724
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Copy cpu/amd/pi/00670F00 to soc/amd/stoneyridge and
soc/amd/common. This is the second patch in the process of
converting Stoney Ridge to soc/.
Changes:
- update Kconfig and Makefiles
- update vendorcode/amd for new soc/ path
Change-Id: I8b6b1991372c2c6a02709777a73615a86e78ac26
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/19723
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Copy the Hudson/Kern code from southbridge/amd/pi/hudson. This
is the first of a series of patches to migrate Stoney Ridge
support from cpu, northbridge, and southbridge to soc/
Changes:
- add soc/amd/stoneyridge and soc/amd/common
- remove all other Husdon versions
- update include paths, etc
- clean up Kconfig and Makefile
- create chip.c to contain chip_ops
Change-Id: Ib88a868e654ad127be70ecc506f6b90b784f8d1b
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/19722
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
This patch updates the coreboot DDR Settings to match the configuration
used by ARM-Trusted-Firmware.
Change-Id: I34bc2950a9708ac89a5637bf682551e03d993fcc
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Reviewed-on: https://review.coreboot.org/20304
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
As per latest BWG, ucode reloading should be done at the end
of Mp Init, i.e., after PRMRR and other features are enabled.
No reloading specifically after SMM Relocation is required.
As, in the Common CPU MP Init code, we are already doing a
uCode load at the end of MP Init Feature Programming, hence,
the uCode loading after SMM relocation can be removed.
Change-Id: Ib1957c5fe5a8c83bb20b978a9841670b0c3e8846
Signed-off-by: Barnali Sarkar <barnali.sarkar@intel.com>
Reviewed-on: https://review.coreboot.org/20306
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This patch uses the common CPU Mp Init code.
BUG=none
BRANCH=none
TEST=Build and boot poppy
Change-Id: Ieb2f8ae25a31e86e9251fe97859678745fe610f5
Signed-off-by: Barnali Sarkar <barnali.sarkar@intel.com>
Reviewed-on: https://review.coreboot.org/20190
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
|
|
This patch contains State Machine callbacks init_cpus()
and post_cpu_init().
Also, it has the SOC call for CPU feature programming.
Change-Id: I5b20d413c85bf7ec6ed89b4cdf1770c33507236b
Signed-off-by: Barnali Sarkar <barnali.sarkar@intel.com>
Reviewed-on: https://review.coreboot.org/20189
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
It does not work to enable the LPC range in the function
mainboard_init() because the LPC bus driver closes the range during PCI
enumeration again. For this reason, enabling decoding of the address
range for COM 3 will be done at a later point in time -
mainboard_final().
Change-Id: I452bca4e430b1ea75e4a327591da84500491fe84
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/20295
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
With enabled XDCI support we are not able to use USB port 0 over XHCI
driver. For this reason, we disable XDCI into devicetree.cb.
Change-Id: I1ed721d9ffd44a920a6f1f16855d5b7ceb1b17c5
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/20296
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
Code checked manually
Change-Id: I92f0b5d47c60c259171c4db90fb5003f4eb8580b
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/20260
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Code checked manually
Change-Id: I5a9596328c028d570303e9390c0133b19b97d683
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/20259
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
|
|
With the do while loop, it can be avoided do use an infinite loop with a
break condition inside.
Change-Id: I030f6782ad618b55112a2f0bac8dda08b497a9f1
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-on: https://review.coreboot.org/20269
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
This fixes improper dram frequency being displayed in sandy bridge
native raminit.
Change-Id: I1fe4e4331f45ce1c21113c039b8433252326293d
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/20229
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
|
|
On boards that are able to take two DIMMs per channel the
command rate should be 2T. It is possible to use 1T with
load reduced "1T" DIMMs, but it's not clear how to detect
those DIMMs. Raminit might fail for those who do not have
such DIMMS installed.
Hardcode command rate of 2T to make sure raminit works on
dual DIMM per channel boards (currently only desktop boards).
The command rate of 1T is still tested if only 1 DIMM per
channel is present.
Will decrease performance on quad slot mainboards, if two DIMMs
are installed in one channel and previously 1T have been selected.
Tested on ASRock B75 Pro3-M.
Change-Id: I029d01092fd0e11390cebcd94ca6f23bf0ee2cab
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/20270
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Maybe we could go on, but cbmem_add() failing is a very bad sign.
Should fix coverity CID 1376384 (Null pointer dereferences
(NULL_RETURNS)).
Change-Id: I330cee6db3540c6a9c408d56da43105de5d075f7
Found-by: Coverity Scan #1376384
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/20280
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
|
|
Fix up for 1b5eda0 (arch/x86/smbios: Fix undefined behavior) which
introduced the variable `tmp` and used it out of scope. Should fix
coverity CID 1376385 (Memory - illegal accesses (RETURN_LOCAL)).
Change-Id: I8d4f664fc54faf6beb432b939dda4ddf93cf5d3e
Found-by: Coverity Scan #1376385
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/20279
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Ryan Salsamendi <rsalsamendi@hotmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
|
|
Bifferboard was the only board that used this chip, and it has now
been removed. Removing the chip as well. If there is desire to
continue work on the board, it can be found in the 4.6 branch.
Change-Id: I33a1e713cdfea47abce71b79f0a9c93562c96d12
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/20262
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
This board can't be found to be tested, and compiles romstage with
romcc. If desired, it can be continued in the 4.6 branch.
Change-Id: I4826c277bbb444c2f0573729d76cd492ade95b4c
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/20261
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Use full text GPLv2 header.
Change-Id: I937aed725ebf0d2e12c52ac4d94794830fbd764d
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/20282
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
|
|
rdrand64() is not clang friendly. Actually it looks like the
function is incorrect on 32bit x86 for all compilers including
gcc, but gcc won't care because the function is never called on
x86:
src/arch/x86/rdrand.c:51:15: error: invalid output size for constraint '=a'
: "=a" (*rand), "=qm" (carry));
^
1 error generated.
Guard the code correctly if ENV_X86_64 is not set.
Change-Id: Ia565897f5e4caaaccfcb02cf1245b150272dff68
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-on: https://review.coreboot.org/20298
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
|