| Age | Commit message (Collapse) | Author |
|---|
|
There are 2 methods currently available in coreboot to load
ramstage from romstage: cbfs and vboot. The vboot path had
to be explicitly enabled and code needed to be added to
each chipset to support both. Additionally, many of the paths
were duplicated between the two. An additional complication
is the presence of having a relocatable ramstage which creates
another path with duplication.
To rectify this situation provide a common API through the
use of a callback to load the ramstage. The rest of the
existing logic to handle all the various cases is put in
a common place.
Change-Id: I5268ce70686cc0d121161a775c3a86ea38a4d8ae
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/5087
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
The arm architectures have a stage_exit() function
which takes a void * pointer as an entry point. Provide
the same API for x86. This can make the booting paths
less architecture-specific.
Change-Id: I4ecfbf32f38f2e3817381b63e1f97e92654c5f97
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/5086
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
It is inappropriate for chipset code to be redefining
types -- especially NULL to a non-pointer type. There's
only one non-straight forward change. A condition
being checked was '!ptr_type == NULL' (0 as int). That
check is actually 'ptr_type != NULL'.
Change-Id: Iab5733e5a573baba6fec94e0c955ba4fad72c836
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/5088
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
The AGESA resumes the GPP ports in the romstage using FchInitResetGpp(),
which does FchGppPortInitS3Phase() for S3 resume. The PreInitGppLink()
looks into CMOS to figure out what ports to just force to Gen1 or
Gen2 PCIe. Then boot continues and in the ramstage the rest of GPP
init is executed. There is a problem that nobody sets properly the
PortDetected flags in the S3 path. As the consequence FchGppDynamicPowerSaving()
thinks the GPP port is not enabled and shut downs it.
The best fix would be also to remove the CMOS dependency which
might be some left over, because AGESA does not use CMOS much for
anything else. There could be also some way how to pass the GPP state
structure from romstage to ramstage possibly via hudson/resume.c
but I don't know how to do that. Similar problem is that the "late"
stage of init again "forgets" the PortDetected state.
This fix fixes the resume issue on Asus F2A85-M. With this patch applied
both GPP ports (used as PCIe x1 and internal ethernet) are working again
after resume.
Change-Id: Idaf609043abb09441c6790504d66d23e0637588f
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Reviewed-on: http://review.coreboot.org/4671
Tested-by: build bot (Jenkins)
Reviewed-by: Idwer Vollering <vidwer@gmail.com>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Certain platforms need to have reference code
packaged and verified through vboot. Therefore,
add this option.
BUG=chrome-os-partner:22867
BRANCH=None
TEST=Built.
Change-Id: Iea4b96bcf334289edbc872a253614bb1bebe196a
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/180025
Reviewed-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: http://review.coreboot.org/5022
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Tested-by: build bot (Jenkins)
|
|
In the case of CONFIG_VBOOT_VERIFY_FIRMWARE not being
selected allow for calling vboot_verify_firmware()
with an empty implementation. This allows for one not to
clutter the source with ifdefs.
BUG=chrome-os-partner:23249
BRANCH=None
TEST=Built with a !CONFIG_VBOOT_VERIFY_FIRMWARE and non-guarded
call to vboot_verify_firmware().
Change-Id: I72af717ede3c5d1db2a1f8e586fefcca82b191d5
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/172711
Reviewed-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: http://review.coreboot.org/4879
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
The Virtual Recovery switch flag needs to be set in coreboot since
it is passed through directly to VBOOT layer by depthcharge.
Rather than add a new config option we can assume that devices with
EC Software Sync also have a virtual recovery switch and set the
flag appropriately.
BUG=chrome-os-partner:25250
BRANCH=all
TEST=build and boot on rambi, successfully enter developer mode
Change-Id: Id067eacbc48bc25a86887bce8395fa3a9b85e9f2
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/183672
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/5061
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
There are 3 places rmodule stages are loaded in the
existing code: cbfs and 2 in vboot_wrapper. Much of the
code is the same except for a few different cbmem entry
ids. Instead provide a common implementation in the
rmodule library itself.
A structure named rmod_stage_load is introduced to manage
the inputs and outputs from the new API.
BUG=chrome-os-partner:22866
BRANCH=None
TEST=Built and booted successfully.
Change-Id: I146055005557e04164e95de4aae8a2bde8713131
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/174425
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/4897
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
|
|
As some of the standard definitions were shuffled around
chromeos started failing to build. Correct this.
Change-Id: I9927441ccb2d646e8b3395e6e9f8e8166de74ab0
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4844
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
Number one reason to use cbfs_get_file was to get file length.
With previous patch no more need for this.
Change-Id: I330dda914d800c991757c5967b11963276ba9e00
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/4674
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Tested-by: build bot (Jenkins)
|
|
Change-Id: I5b93e5321e470f19ad22ca2cfdb1ebf3b340b252
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/4659
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Tested-by: build bot (Jenkins)
|
|
When using RW firmware path the proper recovery reason can
be retrieved from the shared data region. This will result
in the actual reason being logged instead of the default
"recovery button pressed" reason.
1) build and boot on falco
2) crossystem recovery_request=193
3) reboot into recovery mode, check reason with <TAB>
4) reboot back into chromeos
5) check event log entry for previous recovery mode:
25 | 2013-07-15 10:34:23 | Chrome OS Recovery Mode | Test from User Mode
Change-Id: I6f9dfed501f06881e9cf4392724ad28b97521305
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/61906
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4368
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Tested-by: build bot (Jenkins)
|
|
Some files have incorrect/odd permissions,
correct them: remove unnecessary +x flags.
Change-Id: I784e6e599dfee88239f85bb58323aae9e40fb21c
Signed-off-by: Idwer Vollering <vidwer@gmail.com>
Reviewed-on: http://review.coreboot.org/4490
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Bruce Griffith <Bruce.Griffith@se-eng.com>
|
|
Delete files that (were overlooked and) are probably needed to
build with Visual Studio.
Remove doxygen helper files as well.
Change-Id: I6b6cece178917ad9da1081eb6b1bb9be33066a77
Signed-off-by: Idwer Vollering <vidwer@gmail.com>
Reviewed-on: http://review.coreboot.org/4489
Tested-by: build bot (Jenkins)
Reviewed-by: Bruce Griffith <Bruce.Griffith@se-eng.com>
|
|
The bug is hard to find. We were adding the feature of fan control. We
met some strange things which could not be explained. Like, sometimes
adding printk let the error disappear. Then we traced the code by hardware
debug tool (HDT). It turned out the data in stack was overwritten.
The values of AccessWidthxx are
{ AccessWidth8 = 1,
AccessWidth16,
AccessWidth32,}
For the case of AccessWidth8, we only need to access the index/data
once. But ReadECmsg and WriteECmsg did the loop twice, 1 more time
than they are supposed to do. The data in stack next to "Value" would
be overwritten.
For all the cases, the code should be
OpFlag = OpFlag & 0x7f;
switch (OpFlag) {
case 1: /* AccessWidth8 */
OpFlag = 0;break;
case 2: /* AccessWidth16 */
OpFlag = 1;break;
case 3: /* AccessWidth32 */
OpFlag = 3;break;
case 4: /* AccessWidth64 */
OpFlag = 7;break;
default:
error;
}
Actually, the caller only takes AccessWidth8 as the parameter. We can ignore other
cases for now.
That is an AGESA bug. AMD's AGESA team own this code. They have given the
response that they are going to update this in next release. I presume let them
decide the proper way to fix that. Before that, I change the code as little
as possible to make it run without crash.
Change-Id: I566f74c242ce93f4569eedf69ca07d2fb7fb368d
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/4297
Reviewed-by: Bruce Griffith <Bruce.Griffith@se-eng.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
|
|
Add support for Sandybridge and Ivybridge using the Intel FSP.
The FSP is different enough to warrant its own source files.
This source handle the majority of FSP interaction.
"Intel® Firmware Support Package (Intel® FSP) provides key
programming information for initializing Intel® silicon and can be
easily integrated into a boot loader of the developer’s choice.
It is easy to adopt, scalable to design, reduces time-to-market, and
is economical to build."
http://www.intel.com/content/www/us/en/intelligent-systems/intel-firmware-support-package/intel-fsp-overview.html
Change-Id: Ib879c6b0fbf2eb1cbf929a87f592df29ac48bcc5
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-on: http://review.coreboot.org/4015
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
In order to make the proper decision on loading the
option rom or not the recovery mode setting needs to be
known. Normally this is detected by asking the EC,
but if recovery is requested with crossystem then the EC
does not know about it. Instead we need to check the
output flags from VbInit().
Change-Id: I09358e6fd979b4af6b37a13115ac34db3d98b09d
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/57474
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4223
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
|
|
Since we are using VBNV to determine if developer mode is
active we do not need the messy OPROM hook magic any longer.
Change-Id: I1b9effef3ef2aa84e916060d8e61ee42515a2b7c
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/57473
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4222
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Those building Chromebook firmware from coreboot git might be more
interested in building without ChromeOS extras.
Change-Id: I2f176d059fd45bf4eb02cc0f3f1dcc353095d0ce
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3977
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
In order to make the proper decision on loading the
option rom or not the developer mode setting needs to be
known. Under early firmware selection it is possible to know
the state of developer mode by a flag in out flags. Use this
flag when early firmware selection is being employed to determine
if developer mode is enabled or not.
Change-Id: I9c226d368e92ddf8f14ce4dcde00da144de2a5f3
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/57380
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/4218
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
- Disable EC software sync for now
- Report correct EC active firmware mode
- Force enable developer mode by default
- Set up PCH generic decode regions in romstage
- Pass the oprom_is_loaded flag into vboot handoff data
Change-Id: Ib7ab35e6897c19455cbeecba88160ae830ea7984
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/51155
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4169
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
This removes an earlier patch that caused the VGA option ROM to be loaded by
coreboot even in normal mode when it isn't needed.
Change-Id: Ie0a331a10fff212a2394e7234a0dbb37570607b7
Signed-off-by: Bill Richardson <wfrichar@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/48173
Commit-Queue: Stefan Reinauer <reinauer@google.com>
Reviewed-by: Stefan Reinauer <reinauer@google.com>
Tested-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/4125
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Compile was failing with the following error:
In file included from src/vendorcode/google/chromeos/vboot_handoff.h:22:0,
from src/vendorcode/google/chromeos/chromeos.c:22:
vboot_reference/firmware/include/vboot_api.h:388:18: error: unknown type name 'size_t'
src/vendorcode/google/chromeos/chromeos.c: In function 'vboot_get_payload':
src/vendorcode/google/chromeos/chromeos.c:50:23: error: 'NULL' undeclared (first use in this function)
Change-Id: I13f9e41ef6a4151dc65a49eacfa0574083f72978
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/48289
Reviewed-on: http://review.coreboot.org/4131
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
The platform initialization (PI) code v1.0.0.7 for Kabini has some
enhancements like ECC DIMM support, new CPU microcode rev 0700010B, FCH
bug fix (RTC) and so on.
Use the name Kabini instead of Kerala everywhere.
Note, the former PI code was indeed version v1.0.0.0 instead of v0.0.1.0
as used in `AGESA_VERSION_STRING`.
Change-Id: I186de1aef222cd35ea69efa93967a3ffb8da7248
Signed-off-by: WANG Siyuan <SiYuan.Wang@amd.com>
Signed-off-by: WANG Siyuan <wangsiyuanbuaa@gmail.com>
Reviewed-on: http://review.coreboot.org/3935
Tested-by: build bot (Jenkins)
Reviewed-by: Bruce Griffith <Bruce.Griffith@se-eng.com>
|
|
and add an ARMv7 version.
Change-Id: I14fbff88d7c2b003dde57a19bf0ba9640d322156
Signed-off-by: Stefan Reinauer <reinauer@google.com>
[km: rebased fa004acf8 from chromium git]
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3939
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
|
|
Northbridge code includes these headers, so they all need to
have the same name to allow different combinations of northbridge
and southbridge. This changes the sb900 names to match sb700 &
sb800, and points agesa/family12 and amd/torpedo to the new file
names.
Change-Id: I7a654ce9ae591a636a56177f64fb8cb953b4b04f
Signed-off-by: Corey Osgood <corey.osgood@gmail.com>
Reviewed-on: http://review.coreboot.org/3825
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
src/southbridge/amd/agesa/hudson/Kconfig config default value,
mainboard Kconfig config value for specific mainboard.
bit 1,0 - pin 0
bit 3,2 - pin 1
bit 5,4 - pin 2
bit 7,6 - pin 3
Change-Id: I54a87cf734685515a3e1850838ca7d94387172ce
Signed-off-by: WANG Siyuan <SiYuan.Wang@amd.com>
Signed-off-by: WANG Siyuan <wangsiyuanbuaa@gmail.com>
Reviewed-on: http://review.coreboot.org/3879
Tested-by: build bot (Jenkins)
Reviewed-by: Bruce Griffith <Bruce.Griffith@se-eng.com>
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
|
|
Change-Id: Ic7d793754a8b59623b49b7a88c09b5c6b6ef2cf0
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/3768
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Instead of returning 0 on success and -1 on error, return the decompressed
size of the data on success and 0 on error. The decompressed size is useful
information to have that was being thrown away in that function.
Change-Id: If787201aa61456b1e47feaf3a0071c753fa299a3
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3578
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Copied from a similar commit for Family 10h AGESA [1]
Remove the fourth argument in the comments. Luckily the compiler,
at least gcc, warns about a wrong number of arguments, and therefore
no incorrect code resulted from the wrong documentation.
[1] 07e0f1b AMD AGESA: Fix argument list for `PCIE_DDI_DATA_INITIALIZER` in comments
[2] fc47bfa Revert "AMD f14 vendorcode: Fix warning"
Change-Id: I3806e368a823e4a40d22e99b91bf3598d9ed2f15
Signed-off-by: Bruce Griffith <bruce.griffith@se-eng.com>
Reviewed-on: http://review.coreboot.org/3840
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin@se-eng.com>
|
|
This is the same patch as an earlier one applied to family 15 [1].
Static analysis often flags case statements that do not include
a terminating "break;" statement. Eclipse's CODAN is an example
of this. This changelist modifies amdlib.c to terminate
case statements with "break;".
[1] e44a89f amd/agesa/f15/Lib/amdlib.c: Add missing breaks ...
Change-Id: Ibd1ae6f2b52fde07de3d978d174975f4d93647ab
Signed-off-by: Bruce Griffith <Bruce.Griffith@se-eng.com>
Reviewed-on: http://review.coreboot.org/3839
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin@se-eng.com>
|
|
Add CONST modifiers to read-only pass-by-reference function
parameters in AGESA. This allows the use of "const" modifiers
on the declaration of lookup tables that are pass-by-reference.
These will be used to identify tables that are copied onto the
HEAP but don't need to be.
This same change was made for AMD Trinity APUs (Family15tn) [1].
[1] 283ba78 AGESA: Add "const" modifier to function parameters
Change-Id: I2bdd9fc5e027e938de9df0f923b95da934bb48dc
Signed-off-by: Bruce Griffith <Bruce.Griffith@se-eng.com>
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
Tested-by: Bruce Griffith <bruce.griffith@se-eng.com>
Reviewed-on: http://review.coreboot.org/3837
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
|
|
This changelist was cherry-picked from merged community code
for Parmer [1] and the paths modified so that the Parmer
modification is applied against Olive Hill.
[1] 0086162 AMD SATA: Correct _them implement_ ... in comments
Change-Id: I9849e9a75dacfde15331c4200d72343a59036f14
Signed-off-by: Bruce Griffith <bruce.griffith@se-eng.com>
Reviewed-on: http://review.coreboot.org/3841
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Change-Id: Icb6f64e2e3cfd678fb4fb4f13f0e4b678d5acc4a
Signed-off-by: Siyuan Wang <SiYuan.Wang@amd.com>
Signed-off-by: Siyuan Wang <wangsiyuanbuaa@gmail.com>
Reviewed-by: Nick Dill <nick.dill@se-eng.com>
Tested-by: Bruce Griffith <bruce.griffith@se-eng.com>
Reviewed-on: http://review.coreboot.org/3836
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
|
|
Static analysis often flags case statements that do not include
a terminating "break;" statement. Eclipse's CODAN is an example
of this. This changelist modifies amdlib.c to terminate
case statements with "break;".
Change-Id: I3d43acaf64e2e2d9717421cb547fec35e582cf8b
Signed-off-by: Bruce Griffith <Bruce.Griffith@se-eng.com>
Reviewed-on: http://review.coreboot.org/3539
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
This change adds length modifiers to constant values to eliminate
compiler warning messages.
Change-Id: I032cb37cec788e2b5f79f5bbf9efc19a7892dc14
Signed-off-by: Bruce Griffith <Bruce.Griffith@se-eng.com>
Reviewed-on: http://review.coreboot.org/3538
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
This change is mostly type casts to eliminate compile time
warnings. These specific changes are mostly cherry-picked from
AMD Family 14 code and, as such, contain artifacts copied over
from F14. For example, there are a number of UINT64 casts that
are commented out rather than removed. This is to maintain
consistency between AGESA versions. Ultimately, this is in
preparation for turning on warnings as errors for AMD Family 15
server parts.
Change-Id: Ic73d0b6ebab18d97015a9dd1130aff4e5e432fb7
Signed-off-by: Bruce Griffith <Bruce.Griffith@se-eng.com>
Reviewed-on: http://review.coreboot.org/3525
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
fam15 vendorcode (src/vendorcode/amd/agesa/f15tn) was licensed under the
AMD software license agreement. Change this license to 3-clause BSD.
Change-Id: I7cab09bb58ef7cd24602628e2278672d577214a2
Signed-off-by: Siyuan Wang <SiYuan.Wang@amd.com>
Signed-off-by: Siyuan Wang <wangsiyuanbuaa@gmail.com>
Reviewed-on: http://review.coreboot.org/3414
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Add CONST modifiers to read-only pass-by-reference function
parameters in AGESA. This allows the use of "const" modifiers
on the declaration of lookup tables that are pass-by-reference.
These will be used to identify tables that are copied onto the
HEAP but don't need to be.
Change-Id: Ie1187a427804fddf47b935a110ad23931a3447a9
Signed-off-by: Bruce Griffith <Bruce.Griffith@se-eng.com>
Reviewed-on: http://review.coreboot.org/3393
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
It's possible that the vbnv global variables may be accessed
in romstage after cache-as-ram is torn down. Therefore use
the cache-as-ram migration API. Wrappers were written to
wrap the API to keep the existing code as close as possible.
Change-Id: Ia1d8932f98e00def0a44444a1ead0018a59d3d98
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/3234
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
build-snow got broken when the snow makefile improved. So fix it.
While we're at it, create a script like the update-microcode
scripts that gets the bl1. I thought about making this a common
script but the various names and paths always evolve, leaving
me thinking it's not worth it. This script is just a
piece of the snow build script.
Change-Id: I65c0f8697a978c62fe12533c4f0152d14dbaefda
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/3238
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
Reviewed-by: David Hendricks <dhendrix@chromium.org>
|
|
Fix Warning:
cpuFeatureLeveling.c:265, GNU Compiler 4 (gcc), Priority: Normal
cast to pointer from integer of different size [-Wint-to-pointer-cast]
with an intermediate cast to (intptr_t)
Change-Id: I3bfd2ea1e797632316675338789dabef8f73ba64
Signed-off-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-on: http://review.coreboot.org/3126
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
This fixes 3 warnings in the Proc/Common directory:
AmdS3Save.c:250, GNU Compiler 4 (gcc), Priority: Normal
AmdS3LateRestore.c:123, GNU Compiler 4 (gcc), Priority: Normal
cast from pointer to integer of different size [-Wpointer-to-int-cast]
Fixed with a second cast to (intptr_t)
AmdInitReset.c:153, GNU Compiler 4 (gcc), Priority: Normal
statement with no effect [-Wunused-value]
Fixed by commenting the line out as it is in the other families code.
Change-Id: Ib35ec466671712af01568b7c2a18ee138fe883c0
Signed-off-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-on: http://review.coreboot.org/3125
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
The following command was used to correct all occurences of this typo.
$ git grep -l "them implem" | xargs sed -i 's/them implem/then implem/'
Change-Id: Iebd4635867d67861aaf4d4d64ca8a67e87833f38
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/3145
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Because pointers can be 32bit or 64bit big,
using them in the coreboot table requires the
OS and the firmware to operate in the same mode
which is not always the case. Hence, use 64bit
for all pointers stored in the coreboot table.
Guess we'll have to fix this up once we port to
the first 128bit machines.
Change-Id: I46fc1dad530e5230986f7aa5740595428ede4f93
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/3115
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
|
|
When looking into possible reasons for a proposed revert [1], I noticed
that the comments use four arguments for `PCIE_DDI_DATA_INITIALIZER`,
but the actual definition only uses three.
$ git grep -A1 PCIE_DDI_DATA_INITIALIZER # manually squeeze whitespace in output
[…]
--
src/vendorcode/amd/agesa/f10/AGESA.h:#define PCIE_DDI_DATA_INITIALIZER(mConnectorType, mAuxIndex, mHpdIndex ) \
src/vendorcode/amd/agesa/f10/AGESA.h-{mConnectorType, mAuxIndex, mHpdIndex}
--
src/vendorcode/amd/agesa/f10/AGESA.h: * PCIE_DDI_DATA_INITIALIZER (ConnectorType
src/vendorcode/amd/agesa/f10/AGESA.h- * },
--
src/vendorcode/amd/agesa/f10/AGESA.h: * PCIE_DDI_DATA_INITIALIZER (ConnectorType
src/vendorcode/amd/agesa/f10/AGESA.h- * }
--
[…]
So remove the fourth argument in the comments. Luckily the compiler,
at least gcc, warns about a wrong number of arguments, and therefore
no incorrect code resulted from the wrong documentation.
[1] http://review.coreboot.org/#/c/3077/
Change-Id: I3e5a02c66a23af1eb2d86be8dbc7aaa3e5cea05e
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/3080
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Spell RAID correctly in comments. Found with the following command.
$ git grep -i riad
Change-Id: I68e8476d885a88df589d25f88cc158d71eb04e07
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/3081
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
The TPM code wasn't previously honoring MOCK_TPM=1. Because of this,
boards with TPMs that didn't handle S3 resume properly would cause a
hard reset. Allow one to build with MOCK_TPM=1 on the command line so
that S3 can still work.
Change-Id: I9adf06647de285c0b0a3203d8897be90d7783a1e
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2976
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
It's not appropriate for the chromeos Kconfig to automatically
select CACHE_ROM. The reason is that enabling CACHE_ROM is
dependent on the board and chipset atrributes.
Change-Id: I47429f1cceefd40226c4b943215d627a3c869c7b
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2921
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
There were 3 things stopping the vboot module from being
compiled:
1. The vboot_reference code removed in the firmware/arch/$(ARCH)/include
directory. This caused romcc to fail because romcc fails if -I<dir>
points to non-existent directory.
2. The rmodule API does not have the no-clearing-of-bss variant of the
load function.
3. cbfs API changes.
Change-Id: I1e1296c71c5831d56fc9acfaa578c84a948b4ced
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2881
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
coreboot tables are, unlike general system tables, a platform
independent concept. Hence, use the same code for coreboot table
generation on all platforms. lib/coreboot_tables.c is based
on the x86 version of the file, because some important fixes
were missed on the ARMv7 version lately.
Change-Id: Icc38baf609f10536a320d21ac64408bef44bb77d
Signed-off-by: Stefan Reinauer <reinauer@coreboot.org>
Reviewed-on: http://review.coreboot.org/2863
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-by: Aaron Durbin <adurbin@google.com>
Tested-by: build bot (Jenkins)
|
|
The coreboot include were not being passed correctly when
building vboot_reference. The paths being included were of the
src/<dir> form. However, vboot_reference lives in
src/../vboot_reference. That coupled with the recursive make
call made vboot_reference not see coreboot's header files.
Fix this by appending ../ to coreboot's default include paths.
Change-Id: I73949c6f854ecfce77ac36bb995918d51f91445e
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2860
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
The vboot_handoff structure contians the VbInitParams as well as the
shared vboot data. In order for the boot loader to find it, the
structure address and size needs to be obtained from the coreboot
tables.
Change-Id: I6573d479009ccbf373a7325f861bebe8dc9f5cf8
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2857
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
This patch implements support for vboot firmware selection. The vboot
support is comprised of the following pieces:
1. vboot_loader.c - this file contains the entry point,
vboot_verify_firmware(), for romstage to call in order to perform
vboot selection. The loader sets up all the data for the wrapper
to use.
2. vboot_wrapper.c - this file contains the implementation calling the vboot
API. It calls VbInit() and VbSelectFirmware() with the data supplied
by the loader.
The vboot wrapper is compiled and linked as an rmodule and placed in
cbfs as 'fallback/vboot'. It's loaded into memory and relocated just
like the way ramstage would be. After being loaded the loader calls into
wrapper. When the wrapper sees that a given piece of firmware has been
selected it parses firmware component information for a predetermined
number of components.
Vboot result information is passed to downstream users by way of the
vboot_handoff structure. This structure lives in cbmem and contains
the shared data, selected firmware, VbInitParams, and parsed firwmare
components.
During ramstage there are only 2 changes:
1. Copy the shared vboot data from vboot_handoff to the chromeos acpi
table.
2. If a firmware selection was made in romstage the boot loader
component is used for the payload.
Noteable Information:
- no vboot path for S3.
- assumes that all RW firmware contains a book keeping header for the
components that comprise the signed firmware area.
- As sanity check there is a limit to the number of firmware components
contained in a signed firmware area. That's so that an errant value
doesn't cause the size calculation to erroneously read memory it
shouldn't.
- RO normal path isn't supported. It's assumed that firmware will always
load the verified RW on all boots but recovery.
- If vboot requests memory to be cleared it is assumed that the boot
loader will take care of that by looking at the out flags in
VbInitParams.
Built and booted. Noted firmware select worked on an image with
RW firmware support. Also checked that recovery mode worked as well
by choosing the RO path.
Change-Id: I45de725c44ee5b766f866692a20881c42ee11fa8
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2854
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Change-Id: I4aba6cc490ab24c6db345c0c5a64a6a9985ed0ab
Signed-off-by: Siyuan Wang <SiYuan.Wang@amd.com>
Signed-off-by: Siyuan Wang <wangsiyuanbuaa@gmail.com>
Reviewed-on: http://review.coreboot.org/2864
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
|
|
One might wonder what a board named 'build' does. Rename the file to
build-snow. The fact that it is in a directory with google in the name
should be enough to identify the vendor.
Change-Id: I0b473cdce67d56fc6b92032b55180523eb337d66
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/2766
Tested-by: build bot (Jenkins)
Reviewed-by: David Hendricks <dhendrix@chromium.org>
|
|
AGESA code has wrong definition of CR0_PE bit (1 instead of 0).
PE [Protected Mode Enable] is 0 bit in CR0 register
(If PE=1, system is in protected mode, else system is in real mode)
Bit 1 is MP [Monitor co-processor]
(Controls interaction of WAIT/FWAIT instructions with TS flag in CR0)
System uses CR0_PE define, but I didn't expect any consequences because of this bug.
Change-Id: I54d9a8c0ee3af0a2e0267777036f227a9e05f3e1
Signed-off-by: Konstantin Aladyshev <aladyshev@nicevt.ru>
Reviewed-on: http://review.coreboot.org/2591
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
|
|
_RDMSR instruction loads the contents of a 64-bit model specific register (MSR)
specified in the ECX register into registers EDX:EAX.
The EDX register is loaded with the high-order 32 bits of the MSR
and the EAX register is loaded with the low-order 32 bits.
EDX:EAX = MSR[ECX]
So bit 49 will be contained in EDX register.
Buggy code instead of bit 49 (CombineCr0Cd) sets bit [49-32=17] (PfcStrideDis).
PfcStrideDis bit disables stride prefetch generation. This leads to memory
bandwidth loss.
_________
Supermicro H8QGI board
After applying this change i observed huge memory bandwidth increase in tests
that runs on small amount of cores. But unfortunately it doesn't affect
overall bandwidth results on 4P system with 48 cores.
So i think that in this system leading limiting factor is
AMD HT-ASSIST feature (Probe filter).
But right now it is not working. System stucks in Linux boot. I have done
some experiments and figured out that stuck happens when system have cores in
compute unit (CU) other than CU with BSC (boot strap core).
CU is two cores (primary and seconary) that shares some things (L2 cache, FPU ...)
So with probe filter i can boot Linux with one (BSC)
or two (BSC + secondary core in its CU) cores.
And with this configuration i can see memory bandwidth on 1 core (or two cores)
close to original bios.
Change-Id: I5a95f5b753d600c70d3c93d36fecc687610c61cd
Signed-off-by: Konstantin Aladyshev <aladyshev@nicevt.ru>
Reviewed-on: http://review.coreboot.org/2588
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
|
|
In the file `COPYING` in the coreboot repository and upstream [1]
just one space is used.
The following command was used to convert all files.
$ git grep -l 'MA 02' | xargs sed -i 's/MA 02/MA 02/'
[1] http://www.gnu.org/licenses/gpl-2.0.txt
Change-Id: Ic956dab2820a9e2ccb7841cab66966ba168f305f
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2490
Tested-by: build bot (Jenkins)
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
|
|
These were not separable or it would have been two CLs.
Enable CHROMEOS configure option on snow. Write gpio support code for
the mainboard. Right now the GPIO just returns hard-wired values for
"virtual" GPIOs.
Add a chromeos.c file for snow, needed to build.
This is tested and creates gpio table entries that our hardware can use.
Lots still missing but we can now start to fill in the blanks, since
we have enabled CHROMEOS for this board. We are getting further into
the process of actually booting a real kernel.
Change-Id: I5fdc68b0b76f9b2172271e991e11bef16f5adb27
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/2467
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Add brackets around initializer in #define for
PCIE_DDI_DATA_INITIALIZER to fix the warning:
PlatformGnbPcie.c:89, GNU Compiler 4 (gcc), Priority: Normal
missing braces around initializer [-Wmissing-braces]
This warning happens for Inagua and South Station
Change-Id: I7d8f742dd8335b704b0493aa6e9eaebc3cc50b1e
Signed-off-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-on: http://review.coreboot.org/2495
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Add needed prototypes to .h files.
Remove unused variables and fix types in printk statements.
Add #IFNDEFs around #DEFINEs to keep them from being defined twice.
Fix a whole bunch of casts.
Fix undefined pre-increment behaviour in a couple of macros. These now
match the macros in the F14 tree.
Change a value of 0xFF that was getting truncated when being assigned
to a 4-bit bitfield to a value of 0x0f.
This was tested with the torpedo build.
This fixes roughly 132 of the 561 warnings in the coreboot build
so I'm not going to list them all.
Here is a sample of the warnings fixed:
In file included from src/cpu/amd/agesa/family12/model_12_init.c:35:0:
src/include/cpu/amd/amdfam12.h:52:5: warning: redundant redeclaration of 'get_initial_apicid' [-Wredundant-decls]
In file included from src/cpu/amd/agesa/family12/model_12_init.c:34:0:
src/include/cpu/amd/multicore.h:48:5: note: previous declaration of 'get_initial_apicid' was here
src/northbridge/amd/agesa/family12/northbridge.c:50:10: warning: no previous prototype for 'get_node_pci' [-Wmissing-prototypes]
src/northbridge/amd/agesa/family12/northbridge.c: In function 'get_hw_mem_hole_info':
src/northbridge/amd/agesa/family12/northbridge.c:302:13: warning: unused variable 'i' [-Wunused-variable]
src/northbridge/amd/agesa/family12/northbridge.c: In function 'domain_set_resources':
src/northbridge/amd/agesa/family12/northbridge.c:587:5: warning: format '%lx' expects argument of type 'long unsigned int', but argument 3 has type 'device_t' [-Wformat]
src/northbridge/amd/agesa/family12/northbridge.c:587:5: warning: format '%lx' expects argument of type 'long unsigned int', but argument 3 has type 'device_t' [-Wformat]
src/northbridge/amd/agesa/family12/northbridge.c:716:1: warning: format '%x' expects argument of type 'unsigned int', but argument 3 has type 'long unsigned int' [-Wformat]
In file included from src/mainboard/amd/torpedo/agesawrapper.h:31:0,
from src/northbridge/amd/agesa/family12/northbridge.c:38:
src/vendorcode/amd/agesa/f12/AGESA.h:1282:0: warning: "TOP_MEM" redefined [enabled by default]
In file included from src/northbridge/amd/agesa/family12/northbridge.c:34:0:
src/include/cpu/amd/mtrr.h:31:0: note: this is the location of the previous definition
In file included from src/mainboard/amd/torpedo/agesawrapper.h:31:0,
from src/northbridge/amd/agesa/family12/northbridge.c:38:
src/vendorcode/amd/agesa/f12/AGESA.h:1283:0: warning: "TOP_MEM2" redefined [enabled by default]
src/vendorcode/amd/agesa/f12/Proc/GNB/Modules/GnbPcieConfig/PcieInputParser.c: In function 'PcieInputParserGetNumberOfComplexes':
src/vendorcode/amd/agesa/f12/Proc/GNB/Modules/GnbPcieConfig/PcieInputParser.c:99:19: warning: operation on 'ComplexList' may be undefined [-Wsequence-point]
src/vendorcode/amd/agesa/f12/Proc/GNB/Modules/GnbPcieConfig/PcieInputParser.c: In function 'PcieInputParserGetLengthOfPcieEnginesList':
src/vendorcode/amd/agesa/f12/Proc/GNB/Modules/GnbPcieConfig/PcieInputParser.c:126:20: warning: operation on 'PciePortList' may be undefined [-Wsequence-point]
src/vendorcode/amd/agesa/f12/Proc/GNB/Modules/GnbPcieConfig/PcieInputParser.c: In function 'PcieInputParserGetLengthOfDdiEnginesList':
src/vendorcode/amd/agesa/f12/Proc/GNB/Modules/GnbPcieConfig/PcieInputParser.c:153:19: warning: operation on 'DdiLinkList' may be undefined [-Wsequence-point]
src/vendorcode/amd/agesa/f12/Proc/GNB/Modules/GnbPcieConfig/PcieInputParser.c: In function 'PcieInputParserGetComplexDescriptorOfSocket':
src/vendorcode/amd/agesa/f12/Proc/GNB/Modules/GnbPcieConfig/PcieInputParser.c:225:17: warning: operation on 'ComplexList' may be undefined [-Wsequence-point]
src/vendorcode/amd/agesa/f12/Proc/GNB/PCIe/Family/LN/F12PciePhyServices.c:246:1: warning: no previous prototype for 'PcieFmForceDccRecalibrationCallback' [-Wmissing-prototypes]
In file included from src/vendorcode/amd/agesa/f12/Proc/GNB/PCIe/Family/LN/F12PcieComplexConfig.c:58:0:
src/vendorcode/amd/agesa/f12/Proc/GNB/PCIe/Family/LN/LlanoComplexData.h:120:5: warning: large integer implicitly truncated to unsigned type [-Woverflow]
And fixed a boatload of these types of warning:
src/vendorcode/amd/agesa/f12/Proc/CPU/heapManager.c: In function 'HeapGetBaseAddress':
src/vendorcode/amd/agesa/f12/Proc/CPU/heapManager.c:687:17: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
src/vendorcode/amd/agesa/f12/Proc/CPU/heapManager.c:694:19: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
src/vendorcode/amd/agesa/f12/Proc/CPU/heapManager.c:701:23: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
src/vendorcode/amd/agesa/f12/Proc/CPU/heapManager.c:702:23: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
src/vendorcode/amd/agesa/f12/Proc/CPU/heapManager.c:705:23: warning: assignment makes integer from pointer without a cast [enabled by default]
src/vendorcode/amd/agesa/f12/Proc/CPU/heapManager.c:709:21: warning: assignment makes integer from pointer without a cast [enabled by default]
Change-Id: I97fa0b8edb453eb582e4402c66482ae9f0a8f764
Signed-off-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-on: http://review.coreboot.org/2348
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
|
|
Add a prototype to a .h file
Remove an unused file (GppHp.c) from the build by deleting it from the
makefile. I left the file since this is vendorcode. This is the code
for PCIe hotplug.
Inside GppHp.c, make functions not called from outside static.
This obviously isn't important since the file isn't used, but for
the sake of the cleanup I thought I'd go ahead with it...
This was tested with the torpedo build.
This fixes these warnings:
src/vendorcode/amd/cimx/sb900/Dispatcher.c: In function 'LocateImage':
src/vendorcode/amd/cimx/sb900/Dispatcher.c:193:38: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
src/vendorcode/amd/cimx/sb900/Usb.c:740:1: warning: no previous prototype for 'XhciA12Fix' [-Wmissing-prototypes]
src/vendorcode/amd/cimx/sb900/GppHp.c:65:1: warning: no previous prototype for 'sbGppHotPlugSmiProcess' [-Wmissing-prototypes]
src/vendorcode/amd/cimx/sb900/GppHp.c: In function 'sbGppHotPlugSmiProcess':
src/vendorcode/amd/cimx/sb900/GppHp.c:76:5: warning: implicit declaration of function 'SbStall' [-Wimplicit-function-declaration]
src/vendorcode/amd/cimx/sb900/GppHp.c: At top level:
src/vendorcode/amd/cimx/sb900/GppHp.c:101:1: warning: no previous prototype for 'sbGppHotUnplugSmiProcess' [-Wmissing-prototypes]
src/vendorcode/amd/cimx/sb900/GppHp.c:134:1: warning: no previous prototype for 'sbGppHotplugSmiCallback' [-Wmissing-prototypes]
src/vendorcode/amd/cimx/sb900/GppHp.c: In function 'sbGppHotplugSmiCallback':
src/vendorcode/amd/cimx/sb900/GppHp.c:158:5: warning: implicit declaration of function 'outPort80' [-Wimplicit-function-declaration]
Change-Id: I5a1a20eeb81e1f4d59e3e3192f081e11d8506f56
Signed-off-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-on: http://review.coreboot.org/2349
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
This will make the build script wipe out more flash memory content.
Our image is a bit bigger now that we're testing with payloads, so
this is just added paranoia to prevent weird surprises caused by not
flashing the full image.
Change-Id: I31969922079e96886573d9d802266eb0052277cd
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2352
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Added casts and a couple of #ifdefs to fix the warnings in the
vendorcode/amd/agesa/f14 codebase. This will allow us to re-enable
'all warnings being treated as errors' in boards such as Persimmon
that are using this code. That change will follow.
These are the warnings that are fixed by this patch:
src/vendorcode/amd/agesa/f14/Legacy/Proc/hobTransfer.c: In function 'CopyHeapToTempRamAtPost':
src/vendorcode/amd/agesa/f14/Legacy/Proc/hobTransfer.c:219:28: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
src/vendorcode/amd/agesa/f14/Legacy/Proc/hobTransfer.c: In function 'CopyHeapToMainRamAtPost':
src/vendorcode/amd/agesa/f14/Legacy/Proc/hobTransfer.c:372:30: warning: comparison between pointer and integer [enabled by default]
src/vendorcode/amd/agesa/f14/Legacy/Proc/hobTransfer.c:381:33: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
src/vendorcode/amd/agesa/f14/Proc/CPU/cpuApicUtilities.c: In function 'ApUtilSetupIdtForHlt':
src/vendorcode/amd/agesa/f14/Proc/CPU/cpuApicUtilities.c:863:19: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
src/vendorcode/amd/agesa/f14/Proc/CPU/cpuApicUtilities.c:872:18: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
src/vendorcode/amd/agesa/f14/Proc/CPU/cpuMicrocodePatch.c: In function 'LoadMicrocode':
src/vendorcode/amd/agesa/f14/Proc/CPU/cpuMicrocodePatch.c:211:28: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
src/vendorcode/amd/agesa/f14/Proc/CPU/heapManager.c: In function 'HeapManagerInit':
src/vendorcode/amd/agesa/f14/Proc/CPU/heapManager.c:167:52: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
src/vendorcode/amd/agesa/f14/Proc/CPU/heapManager.c:183:14: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
src/vendorcode/amd/agesa/f14/Proc/CPU/heapManager.c: In function 'HeapGetBaseAddress':
src/vendorcode/amd/agesa/f14/Proc/CPU/heapManager.c:669:17: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
src/vendorcode/amd/agesa/f14/Proc/CPU/heapManager.c:676:19: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
src/vendorcode/amd/agesa/f14/Proc/CPU/heapManager.c:683:23: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
src/vendorcode/amd/agesa/f14/Proc/CPU/heapManager.c:684:23: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
src/vendorcode/amd/agesa/f14/Proc/CPU/heapManager.c:687:23: warning: assignment makes integer from pointer without a cast [enabled by default]
src/vendorcode/amd/agesa/f14/Proc/CPU/heapManager.c:691:21: warning: assignment makes integer from pointer without a cast [enabled by default]
src/vendorcode/amd/agesa/f14/Proc/CPU/heapManager.c:696:3: warning: return makes pointer from integer without a cast [enabled by default]
In file included from src/mainboard/amd/persimmon/agesawrapper.h:30:0,
from src/northbridge/amd/agesa/family14/northbridge.c:36:
src/vendorcode/amd/agesa/f14/AGESA.h:1132:0: warning: "TOP_MEM" redefined [enabled by default]
In file included from src/northbridge/amd/agesa/family14/northbridge.c:34:0:
src/include/cpu/amd/mtrr.h:31:0: note: this is the location of the previous definition
In file included from src/mainboard/amd/persimmon/agesawrapper.h:30:0,
from src/northbridge/amd/agesa/family14/northbridge.c:36:
src/vendorcode/amd/agesa/f14/AGESA.h:1133:0: warning: "TOP_MEM2" redefined [enabled by default]
In file included from src/northbridge/amd/agesa/family14/northbridge.c:34:0:
src/include/cpu/amd/mtrr.h:34:0: note: this is the location of the previous definition
Verified on persimmon.
Change-Id: I1671b191c72dfc1d63ada41126ae3418bc8f86ae
Signed-off-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-on: http://review.coreboot.org/2293
Tested-by: build bot (Jenkins)
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Steven Sherk <steven.sherk@se-eng.com>
|
|
Enable 'all warnings being treated as errors' in thatcher and parmer.
Fixed the following warnings on parmer / thatcher:
src/vendorcode/amd/agesa/f15tn/Proc/CPU/Feature/cpuFeatureLeveling.c:
In function 'GetGlobalCpuFeatureListAddress':
src/vendorcode/amd/agesa/f15tn/Proc/CPU/Feature/cpuFeatureLeveling.c:291:14:
warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
src/vendorcode/amd/agesa/f15tn/Proc/CPU/S3.c:
In function 'SaveDeviceContext':
src/vendorcode/amd/agesa/f15tn/Proc/CPU/S3.c:245:18:
warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
src/vendorcode/amd/agesa/f15tn/Proc/CPU/S3.c:309:16:
warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
src/vendorcode/amd/agesa/f15tn/Proc/CPU/cpuPostInit.c:
In function 'GetPstateGatherDataAddressAtPost':
src/vendorcode/amd/agesa/f15tn/Proc/CPU/cpuPostInit.c:235:10:
warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
src/vendorcode/amd/agesa/f15tn/Proc/Mem/NB/TN/mntn.c:
In function 'MemNInitNBDataTN':
src/vendorcode/amd/agesa/f15tn/Proc/Mem/NB/TN/mntn.c:353:32:
warning: assignment from incompatible pointer type [enabled by default]
src/vendorcode/amd/agesa/f15tn/Proc/Mem/NB/TN/mntn.c:363:23:
warning: assignment from incompatible pointer type [enabled by default]
src/vendorcode/amd/agesa/f15tn/Proc/CPU/Feature/cpuFeatureLeveling.c:
In function 'GetGlobalCpuFeatureListAddress':
src/vendorcode/amd/agesa/f15tn/Proc/CPU/Feature/cpuFeatureLeveling.c:291:14:
warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
src/vendorcode/amd/agesa/f15tn/Proc/CPU/S3.c:
In function 'SaveDeviceContext':
src/vendorcode/amd/agesa/f15tn/Proc/CPU/S3.c:245:18:
warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
src/vendorcode/amd/agesa/f15tn/Proc/CPU/S3.c:309:16:
warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
In file included from src/northbridge/amd/agesa/family15tn/northbridge.c:37:0:
src/vendorcode/amd/agesa/f15tn/AGESA.h:1547:0:
warning: "TOP_MEM" redefined [enabled by default]
src/include/cpu/amd/mtrr.h:31:0:
note: this is the location of the previous definition
src/vendorcode/amd/agesa/f15tn/AGESA.h:1548:0:
warning: "TOP_MEM2" redefined [enabled by default]
src/include/cpu/amd/mtrr.h:34:0:
note: this is the location of the previous definition
In file included from src/northbridge/amd/agesa/family15tn/northbridge.c:41:0:
src/vendorcode/amd/agesa/f15tn/Proc/CPU/cpuRegisters.h:378:0:
warning: "LOCAL_APIC_ADDR" redefined [enabled by default]
src/include/cpu/x86/lapic_def.h:9:0: note:
this is the location of the previous definition
In file included from src/mainboard/amd/parmer/BiosCallOuts.h:24:0,
from src/mainboard/amd/parmer/mainboard.c:28:
src/vendorcode/amd/agesa/f15tn/AGESA.h:1547:0:
warning: "TOP_MEM" redefined [enabled by default]
src/include/cpu/amd/mtrr.h:31:0:
note: this is the location of the previous definition
src/vendorcode/amd/agesa/f15tn/AGESA.h:1548:0:
warning: "TOP_MEM2" redefined [enabled by default]
src/include/cpu/amd/mtrr.h:34:0: note:
this is the location of the previous definition
Change-Id: Iecea28232f1761401cf09f7d2a77d3fbac2f5801
Signed-off-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-on: http://review.coreboot.org/2171
Tested-by: build bot (Jenkins)
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
In the AGESA routine GfxInitSview() called in the S3save path,
the IO Space bit was getting cleared from the command register.
This kept seabios from initializing the video bios. If the vbios
was loaded by coreboot, this routine was skipped, allowing seabios
to initialize vbios as well. I have modified the routine to save
and restore the command register instead of clearing the IO Space
bit.
Change-Id: I756b0606adbc47da96780308c911852e39f547c7
Signed-off-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-on: http://review.coreboot.org/2172
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
|
|
The Number of Ports register says that it should be set to the maximum
number of ports supported by the silicon. AGESA was setting this to be
the number of enabled ports. If port 1 was the only port with a drive,
this value got set to 0, indicating 1 port. This causes SeaBIOS to only
look at port 0 and quit, never finding the drive on port 1.
Dave Frodin: I also verified that this patch allows a SATA drive plugged
into port 2 to be detected without a device in port 1.
Change-Id: I5d49e351864449520e3957bbb07edf0f3ec2fd47
Signed-off-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-on: http://review.coreboot.org/2165
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
Reviewed-by: Marc Jones <marcj303@gmail.com>
|
|
Please, don't just add random directories for a single file because
it seems convenient. There already is a chromeos directory, that should
be used.
Change-Id: I625292cac4cbffe31ff3e3d952b11cd82e4b151e
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2137
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
ACPI code:
The ACPI code is not currently being compiled in by default, but
assuming that it will be at some point, I'm fixing the loop that
waits for the IMC to respond after sending it a command. The
loop now exits after 500ms, similar to the function in agesa.
Agesa Code:
a 16 bit variable will always be less than 100000. Change to
be a 32 bit variable.
Change-Id: I9430ef900a22d056871b744f3b1511abdfea516e
Signed-off-by: Martin Roth <martin@se-eng.com>
Reviewed-on: http://review.coreboot.org/2119
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Success return value in DMI functions GetDmiInfoMain(..) and GetType4Type7Info(...) of AGESA vendorcode is "Flag = TRUE".
This results in a failure of init late function:
"agesawrapper_amdinitlate failed: 1"
It happens because TRUE = 1 = AGESA_UNSUPPORTED.
Replacing TRUE with AGESA_SUCCESS (= 0) fixes this problem.
Only family f15tn does not have such bug.
This patch just replaces TRUE with AGESA_SUCCESS, but maybe all DMI functions should be copied from Trinity family?
Tested on Supermicro H8QGI board with 4 AMD Opteron 6234 processors (f15).
Change-Id: I51bf91333c088a825b92d4a44d1ebe4380c8026c
Signed-off-by: Aladyshev Konstantin <aladyshev@nicevt.ru>
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2070
Reviewed-by: Marc Jones <marcj303@gmail.com>
Tested-by: build bot (Jenkins)
|
|
Add configuration for AMD's IMC ROM and fan registers for cimx/sb800
platforms.
- Allows user to add the IMC rom to the build and to configure the
location of the "signature" between the allowed positions.
- Allows for no fan control, manual setup of SB800 Fan registers, or
setup of the IMC fan configuration registers.
- Register configuration is done through devicetree.cb. No files need
to be added for new platform configuration.
- Initial setup is for Persimmon, but may be extended to any cimx/sb800
platform.
Change-Id: Ib06408d794988cbb29eed6adbeeadea8b2629bae
Signed-off-by: Martin Roth <martin@se-eng.com>
Reviewed-on: http://review.coreboot.org/1977
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-by: Marc Jones <marcj303@gmail.com>
|
|
- Add mainboard_smi.c from arch/x86/Makefile if it's there
- Add mainboard's chromeos.c from the chromeos Makefile
Change-Id: I3f80e2cb368f88d2a38036895a19f3576dd9553b
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1835
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
This prepares the way for vboot to inform coreboot when it needs the VGA
Option ROM loaded. Coreboot can't always know when it's needed (with
keyboard-based dev-mode, coreboot can't tell if we're in dev-mode or not).
By the time we get to U-Boot, it's too late, so we need two extra bits - one
for vboot to tell coreboot to load the Option ROM and another for coreboot
to let vboot know it's been done.
This change sets up the communication, but doesn't act on it just yet.
Even with this CL we always load the VGA Option ROM, so there's nothing to
test. There should be no user-visible change.
Change-Id: Ic4e9673a3707b6605064f4879bb3e74d4412322f
Signed-off-by: Bill Richardson <wfrichar@chromium.org>
Reviewed-on: http://review.coreboot.org/1822
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Change-Id: Ie4a98cc8af0dbcf09c7ace79668949ace5938c12
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1752
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
The MRC cache code, as implemented, in some cases uses configuration
settings for MRC cache region, and in some cases - the values read
from FMAP. These do not necessarily match, the code should use FMAP
across the board.
This change also refactors mrccache.c to limit number of iterations
through the cache area and number of fmap area searches.
Change-Id: Idb9cb70ead4baa3601aa244afc326d5be0d06446
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: http://review.coreboot.org/1788
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
The RO_FMAP base moved from 0x5f0000 to 0x610000.
Also update Kconfig default and add a descripton so
the default can be changed by boards.
Change-Id: I0caad0ce6e6f19750dbbf042a5a489b558f62b96
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1705
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
|
|
Now that we have FMAP support in coreboot use it to find the
offset in flash for ELOG to use.
If coreboot has elog configured with a smaller size then use
that over the FMAP size. This is because I set aside a 16KB
region in the FMAP but we only use 4KB of it to keep the impact
to boot/resume speed to a minimum.
FMAP: Found "FMAP" version 1.0 at ffe10000.
FMAP: base = 0 size = 800000 #areas = 32
FMAP: area RW_ELOG found
FMAP: offset: 3f0000
FMAP: size: 16384 bytes
FMAP: No valid base address, using 0xff800000
ELOG: base=0x003f0000 base_ptr=0xffbf0000
ELOG: MEM @0x00190ad8 FLASH @0xffbf0000
ELOG: areas are 4096 bytes, full threshold 3072, shrink size 1024
Change-Id: I3d826812c0f259d61f41b42797c58dd179f9f1c8
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1706
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Until now, the MRC cache position and size was hard coded in Kconfig.
However, on ChromeOS devices, it should be determined by reading the
FMAP.
This patch provides a minimalistic FMAP parser (libflashmap was too
complex and OS centered) to allow reading the in-ROM flash map and
look for sections.
This will also be needed on some partner devices where coreboot will
have to find the VPD in order to set up the device's mac address
correctly.
The MRC cache implementation demonstrates how to use the FMAP parser.
Change-Id: I34964b72587443a6ca4f27407d778af8728565f8
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1701
Reviewed-by: Marc Jones <marcj303@gmail.com>
Tested-by: build bot (Jenkins)
|
|
Current ExecuteFinalHltInstruction function doesn't work well.
(at least in configuration
Supermicro board with Orochi AMD Opteron processors (model OS6234WKTCGGU))
System reboots when trying to halt core 2,4,6,8 or 10
(OS6234WKTCGGU is 12 core processor)
Based on this information, i think that code doesn't really work with
f15 compute unit (CU) system.
Replacing ExecuteFinalHltInstruction function with
analogous function from f15tn family code fix this problem.
Both functions written from the same cahalt.asm file, but f15tn version
seems more completed
Change-Id: I3942abcdf21f1b86a44c01cc477714e44a40b9cf
Signed-off-by: Kostr <aladyshev@nicevt.ru>
Reviewed-on: http://review.coreboot.org/1569
Tested-by: build bot (Jenkins)
Reviewed-by: Siyuan Wang <wangsiyuanbuaa@gmail.com>
Reviewed-by: Marc Jones <marcj303@gmail.com>
|
|
src/vendorcode/amd/agesa/f15/Porting.h has some conflicted typedef with
src/include/cpu/amd/common/cbtypes.h. These conflicted defines can lead to errors.
Change-Id: Idad0794018bf0bd0e4e52a5aa062a12766d56c8e
Signed-off-by: Siyuan Wang <SiYuan.Wang@amd.com>
Signed-off-by: Siyuan Wang <wangsiyuanbuaa@gmail.com>
Reviewed-on: http://review.coreboot.org/1592
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Something about HD audio was scrubbed. Take it back.
Change-Id: I0be96fd103f3ebd4e8c7ef09a184b71aa34ee3fd
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: zbao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/1427
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
|
|
Recent changes in EC/Vboot/U-boot have completely broken
the logging of developer and recovery modes.
Recovery mode may not be in VBNV, so if that is zero and
yet we are in recovery mode then assume it is there because
the button/key was pressed.
Since there may not be any actual developer mode switch
we look if option rom is loaded and the system is not
in recovery mode and consider that as developer mode.
Change-Id: I70104877b24de477217e1ff5b3a019aef22343ec
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1346
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
If a Chrome OS device is in developer mode log an event.
When the device is in recovery mode also log an event
and provide the recovery reason.
Enable developer mode and trigger recovery mode and
verify that the events are logged:
238 | 2012-06-23 17:31:56 | Chrome OS Developer Mode
239 | 2012-06-23 17:31:56 | Chrome OS Recovery Mode | User Requested from Developer Screen
Change-Id: I14d41f44e04fd91340569617c7314da7e35a154f
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1321
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
The default return value should be AGESA_SUCCESS, which is zero. If it was set as TRUE,
the AGESA wrapper would think it was AGESA_UNSUPPORTED. That would make no sense. And it
would produce ASSERT warning in AGESA wrapper.
On my parmer board, with Engine sample processor, it can not create the correct DMI table.
Routine initlate will return AGESS_ERROR.
------Serial message---------
ASSERTION FAILED: file 'src/mainboard/amd/parmer/agesawrapper.c', line 427
DmiTable:100123c3, AcpiPstatein: 10010126, AcpiSrat:0,AcpiSlit:0, Mce:100111ba, Cmc:1001127c,Alib:1001ccd4, AcpiIvrs:0 in agesawrapper_amdinitlate
agesawrapper_amdinitlate failed: 5
-----------------------------
I believe the processor with acceptable name string will create the right DMI.
Change-Id: Ie86955cf9affffc964a7c9f4a2c63077ef2030de
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: zbao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/1350
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
coreboot used to pass some information to u-boot in the coreboot table
and other information in a modified flat device tree. Since the FDT code
was never upstreamed and removed from our tree, u-boot was changed to
get the information it needs from the coreboot table alone. However,
in the process of this change only the vboot shared data structure was
passed on by coreboot, so when u-boot tried to update the ChromeOS
specific ACPI entries, it would accidently overwrite the vboot data.
This patch passes on the ChromeOS specific ACPI data structure instead
of the vboot shared data. Another change to u-boot will teach it how
to get to the vboot shared data from there.
Change-Id: Ifbb64eafc0d9967887b4cdeebf97d0c4ce019290
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1282
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
The only difference in this code on all our platforms is the array
describing the GPIOs. Hence, only keep that array in the mainboard
ChromeOS directory and move everything else to generic ChromeOS ACPI
code.
Change-Id: I9fc75842af64530c1255bea1c5f803c5316d6da6
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1278
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
AMD AGESA code for trinity.
Change-Id: I847a54b15e8ce03ad5dbc17b95ee6771a9da0592
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: zbao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/1155
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Originally, on ChromeBooks, coreboot would provide a modified
u-boot device tree (FDT) to u-boot in CBMEM. However, u-boot
can now create all the information it needs from the coreboot
table and add it to its device tree itself. This means we can
drop this (anyways unused) code.
Change-Id: I4ab20bbb8525e7349b18764aa202bbe81958d06a
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1052
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Remove all the repeated sections of code in cbtypes.h and place it
in a common location. Add include dir in vendor code's Makefile.
Change-Id: Ida92c2a7a88e9520b84b0dcbbf37cd5c9f63f798
Signed-off-by: Vikram Narayanan <vikram186@gmail.com>
Reviewed-on: http://review.coreboot.org/912
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
|
|
For legacy free AMD systems, the #define LEGACY_FREE cannot
currently be overridden. This patch allows the platform_cfg.h
to override that. (I know we want to get away from that, but
for now...)
Also allow BIOS_SIZE to be overridden on SB700 cimx based
platforms.
Change-Id: I570115248bcbc686062bfb66acb56208240b847a
Signed-off-by: Martin L Roth <martin@se-eng.com>
Reviewed-on: http://review.coreboot.org/1018
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
|
|
Change source file modes from 755 to 644
The following files have been grepped for changes:
*.c
*.h
*Kconfig*
*Makefile*
Change-Id: I275f42ac7c4df894380d0492bca65c16a057376c
Signed-off-by: Alec Ari <neotheuser@ymail.com>
Reviewed-on: http://review.coreboot.org/1023
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
string.h is required to build with the reference toolchain.
Change-Id: I9fd8d2ea8fc676d3502989cbcc7aefe3b2d738b6
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/935
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Change the ExecuteFinalHltInstruction to assembly code. so we can make
sure the code can run stackless.
Change-Id: I783ced6cf7c5bc29c12a37aef29077e610d8957d
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: zbao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/622
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Google ChromeOS specific options were shown in the main menu
unconditionally, even on non-ChromeOS devices. Instead, hide
these options unless CONFIG_CHROMEOS is set, and also put them
in a separate menu.
Change-Id: I75f533ed5046d6df4f7d959a0ca4c2441340ef2f
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/848
Reviewed-by: Martin Roth <martin@se-eng.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Mathias Krause <minipli@googlemail.com>
|
|
some blank changing is integrated into the previous patches, which hold
the unsplitted diff hunk.
Change-Id: If9e5066927c5e27fee7ac8422dbfbf2cbeac7df5
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: zbao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/625
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
|
|
Google's ChromeOS can be booted super fast and safely
using coreboot. This adds the ChromeOS specific code that
is required by all ChromeBooks to do this.
Change-Id: Ic03ff090a569a27acbd798ce1e5f89a34897a2f2
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/817
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
and initialize the TPM on S3 resume
This patch integrates the TPM driver and runs TPM resume upon an ACPI S3
resume without including any other parts of vboot.
We could link against vboot_fw.a but it is compiled with u-boot's CFLAGS
(that are incompatible with coreboot's) and it does a lot more than we
want it to do.
Change-Id: I000d4322ef313e931e23c56defaa17e3a4d7f8cf
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/731
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
... and hook it up in Kconfig. More code to come.
Change-Id: I24542d8ef97e2bce112c3aface681ceeb1a7c061
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/813
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Fixes the warnings generated in the torpedo mainboard build by AGESA.
Removing broken tests.
Change-Id: Ib444fa2bf4dd94cadb4ce33040eb5650d1c0325b
Signed-off-by: Martin L Roth <martin@se-eng.com>
Reviewed-on: http://review.coreboot.org/667
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
