| Age | Commit message (Collapse) | Author |
|---|
|
Change-Id: I074d57fa5b140b6946ae81beb210fefac48a66eb
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/28226
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
There is no public datasheet available for this SuperIO so the resources are
guessed by looking at other ITE SuperIO's and the register dumps while running
vendor firmware.
The only board with this SuperIO in the tree is the asus m5a88-v. Most of the
devicetree entries would have been invalid here so one should not worry too much
about regressions.
Tested with Foxconn d41s.
Change-Id: I6715c68b3aa9aebf6e292975cbf64ce905b30e8b
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/28225
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
The existing code for modifying the power state after power loss of the system
only implemented the transitions from power off to either power on or power keep
properly.
Since I don't have a board with this chip, I couldn't test the patch on real
hardware. The two cases described above were tested before the original patch
was merged, so I'd expect this to work.
Change-Id: I3c26a2837e451dbfd3cee82e9beedc0f4a90af03
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/27648
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Change-Id: Iadc28d1632aa9b7d0b028c229049a348d5c07882
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/27875
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Pass the address of the chip-specific ops struct instead of the one of the
generic pnp_ops struct to the PNP device enable function.
This allows the removal of the LDN-specific ops overrides which is also done in
this patch.
Change-Id: I5f03a4064778c419f4b9c50e70db1296addf6c9e
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/23006
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Change-Id: I2829e4cb1445f8412f57da10fda6b92c92e56ea0
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/26650
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Program the Super I/O to turn the machine on or restore its power state
when AC power is restored.
Based on code from src/superio/nuvoton/nct5572d/superio.c.
Change-Id: I1f3432f43b0784c3696bf1d7233b83d3a203af20
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-on: https://review.coreboot.org/25463
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Copies the common/env_ctrl support code from the it8728f driver.
Tested on an ASUS AM1I-A using Linux 4.16.7-gentoo as payload,
and booting userspace without a kexec call.
Prior to this change, an error was given during boot:
it87 it87.656: Detected broken BIOS defaults, disabling PWM interface
After this change, the message is gone, and PWM fan control works
through the /sys/class/hwmon interface.
Change-Id: Id97c4ec19562e7c78308c5afe6ff7c938922c9e7
Signed-off-by: Kevin Cody-Little <kcodyjr@gmail.com>
Reviewed-on: https://review.coreboot.org/26224
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add device tree options to enable beeps when exceeding temperature,
voltage, and fan limits. As of this commit, setting voltage and fan
limits is not implemented.
Change-Id: I57ce622ee4498b75f00e678c2e6d72e499925bce
Signed-off-by: Vagiz Trakhanov <rakkin@autistici.org>
Reviewed-on: https://review.coreboot.org/22141
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
This change adds basic support for the SuperIO chip ITE IT8623E.
Due to the lack of a datasheet, defaults are shown as "not available (NA)"
in superiotool's register dump. LDNs defined in it8623e.h are
definitely correct and working as expected.
Change-Id: I05832c4db7ab59541337f11200640316376e792e
Signed-off-by: Gergely Kiss <mail.gery@gmail.com>
Reviewed-on: https://review.coreboot.org/23001
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
This fixes the bug that the LDNs on the affected SIO chips didn't get
configured, since the config mode wasn't entered.
Change-Id: Ic468847571e164e4e1280428f08fc067b724464e
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/23004
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Instead of setting "peci_tmpin" in the devicetree, THERMAL_PECI is now
a mode of TMPIN like THERMAL_RESISTOR and THERMAL_DIODE. Since the logic
to set temperature offsets and limits is in the function that sets
thermal modes, it makes sense to treat PECI as yet another mode.
As of this commit, there are no boards that actually use peci_tmpin from
ite/common. There are three boards that have a similar device tree
option, but those boards use it8772f, which implements all superio
functions on its own.
The first user will probably be Gigabyte GA-Z77-DS3H.
Change-Id: I39da50c124ad767f8681302733cf004622975e81
Signed-off-by: Vagiz Trakhanov <rakkin@autistici.org>
Reviewed-on: https://review.coreboot.org/22076
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Add devicetree options to set temperature limits that are used to alarm
user when temperature exceeds defined values.
Audio alerts by superio are not implemented yet, but since limits are
visible to userland, some software might use them as is. For instance,
lm-sensors displays "ALERT" when temperature exceeds limits.
Change-Id: I56e041fb78f518d6a9640dc2b3985459991242b9
Signed-off-by: Vagiz Tarkhanov <rakkin@autistici.org>
Reviewed-on: https://review.coreboot.org/21844
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Add a devicetree option to set temperature adjustment registers
required for thermal diode sensors and PECI. However, this commit does
not have the code needed to make PECI interface actually use these
registers. It only applies to diodes.
As a temporary workaround, one can set both THERMAL_DIODE and peci_tmpin
to the same TMPIN, e.g. TMPIN3.mode="THERMAL_DIODE" and peci_tmpin="3".
PECI, apparently, takes precedence over diode, so the adjustment register
will be set and PECI activated. Or simply use the followup patch, which
makes THERMAL_PECI a mode like THERMAL_DIODE.
I don't have hardware to test THERMAL_DIODE mode, but in case of PECI,
without this patch I had about -60°C on idle. Now, with offset 97,
which was taken from vendor bios, PECI readings became reasonable 35°C.
TEST=Set a temperature offset, then ensure that the value you set is
reflected in /sys/class/hwmon/hwmon*/temp[1-3]_offset
Change-Id: Ibce6809ca86b6c7c0c696676e309665fc57965d4
Signed-off-by: Vagiz Tarkhanov <rakkin@autistici.org>
Reviewed-on: https://review.coreboot.org/21843
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
This is a follow-on to the superio IS_ENABLED() patch:
https://review.coreboot.org/#/c/20351/1
Change-Id: I7d070e3964609947959de60e2686dfe59fe77e1c
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/20490
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Change-Id: Ie9a7127b50db8dc9a2b543843ca4d815afe3d07e
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/20351
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
The 'set' field was not used anywhere. Replace the struct with a simple
integer representing the mask.
initializer updates performed with:
sed -i -r 's/\{ ?0(x([[:digit:]abcdefABCDEF]{3,4}))?, (0x)?[04]? ?\}/0\1/g' \
src/ec/*/*/ec.c
sed -i -r 's/\{ ?0(x([[:digit:]abcdefABCDEF]{3,4}))?, (0x)?[04] ?\}/0\1/g' \
src/ec/*/*/ec_lpc.c \
src/superio/*/*/superio.c \
src/superio/smsc/fdc37n972/fdc37n972.c \
src/superio/smsc/sio10n268/sio10n268.c \
src/superio/via/vt1211/vt1211.c
src/ec/kontron/it8516e/ec.c was manually updated. The previous value for
IT8516E_LDN_SWUC appears to have been a typo, as it was out of range and
had a zero bit in the middle of the mask.
Change-Id: I1e7853844605cd2a6d568caf05488e1218fb53f9
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-on: https://review.coreboot.org/20078
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Myles Watson <mylesgw@gmail.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
This device is extremely similar to the IT8718F, so support is based on
existing support for the IT8718F. The CIR device is only detected by
Linux/Windows from the ACPI tables, so ACPI support is extended from the
IT8783E/F (for ACPI). This Super I/O is used on the Foxconn G41S-K.
Tested, working:
* Serial port 1
* Environment controller
- Temperature monitoring
- Voltage monitoring
- Fan control (automatic and manual)
* PS/2 keyboard and mouse
Appears, OS driver loads, but otherwise untested:
* Serial port 2
* Consumer IR
Untested:
* Floppy controller
* Parallel port
* GPIO
Change-Id: Ib9a6fe91a772d78f4d122a6c516feff8658ada0a
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-on: https://review.coreboot.org/20026
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Change-Id: Ifcbf95ffd6d13cae4e6864e0320ce6ce1cf3ae4d
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-on: https://review.coreboot.org/20025
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philippe Mathieu-Daudé <philippe.mathieu.daude@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Change-Id: Id4a079d868c5c806c769b5559833566e8a6a8a71
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-on: https://review.coreboot.org/20077
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
This replaces the custom environment controller handling in the it8728
driver with the common library.
It also updates the two existing boards with hwm register settings in
their devicetree config so they better match their vendor BIOS fan
control settings.
Change-Id: Idf0c8908ba5ad6ff552b8302bffc638aa9052941
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Reviewed-on: https://review.coreboot.org/19293
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Current ACPI code for UARTs uses the PNP_DEFAULT_PSC macro for _PSC
(current power state) methods. Override it to `Return (0)` (i.e. cur-
rent state is D0) as the IT8783E/F doesn't have power management.
Change-Id: I3c858dde287dbf7e5fc0c20abb1fd374887acdde
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/17791
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
This will be used by new Roda boards. Four UARTs and PS/2 keyboard and
mouse are exposed to ACPI. Since our boards only use the environment
controller part, most of the usual pnp interfaces are untested.
Change-Id: Ifeb0327ad115759411716f82585ace5ce55b8464
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/17287
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Change-Id: I8cbfe49516e685c1b3e150b23f9fcac513f1f3dc
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/17285
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
The devicetree parameter already existed without being
used in the code.
Change-Id: I99dd8bc7a9b2f3509a115a130062d462a62e33fd
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/17614
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Change-Id: I25019c6323b6e9de2e0ce19325266bf3e8f2e309
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/17581
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Change-Id: I597ba3a03bd42c64d03137b10a3758d86b129029
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/17452
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
The environment-controller entity is shared by many ITE super-i/o
chips. There are some differences between the chips, though. To cover
that, the super-i/o chip should select Kconfig options of this driver
accordingly.
The current implementation isn't exhaustive: It covers only those
parts that are connected on boards I could test, plus those that are
currently used by the IT8772F. The latter could be ported to use this
driver if somebody minds to test it.
Change-Id: I7a40f677f667d103ce1d09a3e468915729067803
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/17284
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Change-Id: I8597d205ca84bee0171c3d45549a28b58a050529
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/16433
Tested-by: build bot (Jenkins)
Reviewed-by: Antonello Dettori <dev@dettori.io>
|
|
This moves the Kconfig from the Super I/O manufacturer folder
to the chip folder instead.
This makes new chip commits self-contained unit as
edits to the central Kconfig file are no longer required.
Change-Id: I7aee07919f2ae9204850c669e0ed3cb17d4de8cd
Signed-off-by: Omar Pakker <omarpakker+coreboot@gmail.com>
Reviewed-on: https://review.coreboot.org/15973
Tested-by: build bot (Jenkins)
Reviewed-by: Idwer Vollering <vidwer@gmail.com>
|
|
On certain Winbond SuperIO devices, when a PS/2 mouse is not
present on the auxiliary channel both channels will cease to
function if the auxiliary channel is probed while the primary
channel is active. Therefore, knowledge of mouse presence
must be gathered by coreboot during early boot, and used to
enable or disable the auxiliary PS/2 port before control is
passed to the operating system.
Add auxiliary channel PS/2 device presence detect, and update
the Winbond W83667HG-A driver to flag the auxiliary channel as
disabled if no device was detected.
Change-Id: I76274493dacc9016ac6d0dff8548d1dc931c6266
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: https://review.coreboot.org/13165
Tested-by: build bot (Jenkins)
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
This just updates existing guard name comments on the header files
to match the actual #define name.
As a side effect, if there was no newline at the end of these files,
one was added.
Change-Id: Ia2cd8057f2b1ceb0fa1b946e85e0c16a327a04d7
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/12900
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Original-Signed-off-by: Ted Kuo <tedkuo@ami.com.tw>
Change-Id: I70d7b572e9ae030136a39fb6fa933f486d559aef
Original-Reviewed-on: https://chromium-review.googlesource.com/262832
Original-Reviewed-by: Shawn N <shawnn@chromium.org>
Original-Commit-Queue: Ted Kuo <tedkuo@ami.com.tw>
Original-Tested-by: Ted Kuo <tedkuo@ami.com.tw>
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/12799
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
Set up External Temperature to read via thermal diode/resistor
into TMPINx register by setting thermal_mode switch.
Original-Signed-off-by: Ted Kuo <tedkuo@ami.com.tw>
Change-Id: I0e8621b92faa5c6246e009d2f852c8d4db484034
Original-Reviewed-on: https://chromium-review.googlesource.com/260545
Original-Reviewed-by: Shawn N <shawnn@chromium.org>
Original-Tested-by: Ted Kuo <tedkuo@ami.com.tw>
Original-(cherry picked from commit 973e2d393f2595b756f8aa20f6fbe3b6e045621a)
Original-Reviewed-on: https://chromium-review.googlesource.com/262340
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/12798
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
Change-Id: Id6d50d4d6af31e43f851645f09383121755291f6
Signed-off-by: Damien Zammit <damien@zamaudio.com>
Reviewed-on: https://review.coreboot.org/12815
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
According to the PNP ISA v1.0a spec, config registers in the range of
0xf0 up to 0xfe are vendor defined and may be used for any purpose.
Config register 0xff is reserved and is defined as such.
Currently, only vendor specific registers 0xf0, 0xf1, 0xf4, and 0xfa
are able to be set using the PNP_MSCx bit flag masks.
This patch adds support for all 15 vendor specific config registers,
and updates the existing superio pnp_info to use them where appropriate.
Change-Id: Id43b85f74e3192b17dbd7e54c4c6136a2e59ad55
Signed-off-by: Damien Zammit <damien@zamaudio.com>
Reviewed-on: https://review.coreboot.org/12808
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
- Remove it8772f c includes
- Add a new LED API, it8772f_gpio_led
- Stumpy: using it8772f_gpio_led
BUG=chrome-os-partner:28232
BRANCH=Guado
TEST=emerge-guado coreboot chromeos-bootimage
Change-Id: I08de52515d3c1e7e85d1761c09a0cebffda7dda3
Signed-off-by: David Wu <David_Wu@quantatw.com>
Reviewed-on: https://chromium-review.googlesource.com/241813
Tested-by: David Wu <david_wu@quantatw.com>
Reviewed-by: Shawn N <shawnn@chromium.org>
Commit-Queue: David Wu <david_wu@quantatw.com>
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/12797
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
It encourages users from writing to the FSF without giving an address.
Linux also prefers to drop that and their checkpatch.pl (that we
imported) looks out for that.
This is the result of util/scripts/no-fsf-addresses.sh with no further
editing.
Change-Id: Ie96faea295fe001911d77dbc51e9a6789558fbd6
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Reviewed-on: http://review.coreboot.org/11888
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
All boards using this SuperIO have been removed from the tree already.
Change-Id: Ifca91ae44ab222371808ff1e0027a7cbd4646b0a
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-on: http://review.coreboot.org/12243
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
As per discussion with lawyers[tm], it's not a good idea to
shorten the license header too much - not for legal reasons
but because there are tools that look for them, and giving
them a standard pattern simplifies things.
However, we got confirmation that we don't have to update
every file ever added to coreboot whenever the FSF gets a
new lease, but can drop the address instead.
util/kconfig is excluded because that's imported code that
we may want to synchronize every now and then.
$ find * -type f -exec sed -i "s:Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, *MA[, ]*02110-1301[, ]*USA:Foundation, Inc.:" {} +
$ find * -type f -exec sed -i "s:Foundation, Inc., 51 Franklin Street, Suite 500, Boston, MA 02110-1335, USA:Foundation, Inc.:" {} +
$ find * -type f -exec sed -i "s:Foundation, Inc., 59 Temple Place[-, ]*Suite 330, Boston, MA *02111-1307[, ]*USA:Foundation, Inc.:" {} +
$ find * -type f -exec sed -i "s:Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.:Foundation, Inc.:" {} +
$ find * -type f
-a \! -name \*.patch \
-a \! -name \*_shipped \
-a \! -name LICENSE_GPL \
-a \! -name LGPL.txt \
-a \! -name COPYING \
-a \! -name DISCLAIMER \
-exec sed -i "/Foundation, Inc./ N;s:Foundation, Inc.* USA\.* *:Foundation, Inc. :;s:Foundation, Inc. $:Foundation, Inc.:" {} +
Change-Id: Icc968a5a5f3a5df8d32b940f9cdb35350654bef9
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Reviewed-on: http://review.coreboot.org/9233
Tested-by: build bot (Jenkins)
Reviewed-by: Vladimir Serbinenko <phcoder@gmail.com>
|
|
Replace the multiple indexed I/O read and write
functions with common functions.
Change-Id: Idfe7a8784c28d51b3fbcb2f4e26beaa0b91741a8
Signed-off-by: Dave Frodin <dave.frodin@se-eng.com>
Reviewed-on: http://review.coreboot.org/10145
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
|
|
It causes fan top speed due to this bug + our board-specific workaround,
and causes invalid temperature sensor readings.
Therefore, re-configure the register "External Temperature Sensor Host
Control Register" to terminate processes when this issue happens.
BUG=chromium:402204
TEST=ran suspend_stress_test 500 times
Change-Id: I439d5de798fbe999e4eec5497e6969b7b453121b
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: b82f2922c7fce3ca6b2797a8d9775e9db2817fe9
Original-Change-Id: I6e71b6a46a31b00e541c304f1ed58c1678c1d42e
Original-Signed-off-by: Ryan Lin <ryan.lin@intel.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/219445
Original-Reviewed-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: http://review.coreboot.org/8820
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
We already have these implemented under superio/common, use
those instead of this copy-paste syndrom.
Change-Id: I7c7737e0b3c284d8b14b36c70681ab2269bb1d4b
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/7310
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Change-Id: Id88bb4367d6045f6fbf185f0562ac72c04ee5f84
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: http://review.coreboot.org/7146
Tested-by: build bot (Jenkins)
|
|
Hiding pointer types behind 'typedef's is usually not a great
idea at the best of times. Worse the typedef becomes an integer
at different stages in Coreboot. Let us refrain from doing this
at all.
Change-Id: Ia2ca8c98bb489daaa58f379433875864f6efabc8
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/7136
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
The romstage component of Super I/O support is in fact written around
passing a lower and upper half packed integer. We currently have two
typedef's for this, 'device_t' and 'pnp_devfn_t'. We wish to make use of
'pnp_devfn_t' over 'device_t' as 'device_t' changes it's typedef in the
ramstage context and so is really a conflicting definition. This helps
solve problems down the road to having the 'real' 'device_t' definition
usable in romstage later.
This follows on from the rational given in:
c2956e7 device/pci_early.c: Mixes up variants of a typedefs to 'u32'
Change-Id: Ia9f238ebb944f9fe7b274621ee0c09a6de288a76
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/6231
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins)
|
|
Change-Id: I602f970e0ee2fd634a74fd4c25358c2e78ca58f9
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: https://chromium-review.googlesource.com/179536
Commit-Queue: Stefan Reinauer <reinauer@chromium.org>
Tested-by: Stefan Reinauer <reinauer@chromium.org>
Reviewed-by: Shawn Nematbakhsh <shawnn@chromium.org>
(cherry picked from commit 02b0583e632f1ba53557f8cfe4293ad4ed29ff4d)
Signed-off-by: Isaac Christensen <isaac.christensen@se-eng.com>
Reviewed-on: http://review.coreboot.org/6910
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
|
|
Change-Id: I45885905f0adaa8f0ad9137d7034e6f7a0dc43de
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: https://chromium-review.googlesource.com/175356
Reviewed-by: Stefan Reinauer <reinauer@chromium.org>
Commit-Queue: Stefan Reinauer <reinauer@chromium.org>
Tested-by: Stefan Reinauer <reinauer@chromium.org>
(cherry picked from commit 7fe642543a8de249e13c3d63c3302a20910c247d)
Signed-off-by: Isaac Christensen <isaac.christensen@se-eng.com>
Reviewed-on: http://review.coreboot.org/6859
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Remove #include early_serial.c and rename to early_init.c as no actual
UART configuration is done here. Note that this SIO component still
hard codes its base address to 0x2e.
Change-Id: Ieef32ac7285246717f0519ffed4314ba28cd47dc
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/6271
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Change-Id: Iaf5db7153b08ac81b233f967c7a604ed08af91ca
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/6040
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: David Hendricks <dhendrix@chromium.org>
|
|
Following similar reasoning as commit:
d304331 superio/fintek/f81865f: Avoid .c includes
Avoid any mistaken future inclusion of early_serial.c in mainboard.c
code by providing symbols in romstage.
Change-Id: I9e763a7ad9de090e35acdcf4d6a280d8227c6015
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/5508
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
We have better written generic implementations of these functions
introduced in commit:
a7d14a1 ite/common: Introduce common watchdog and 3.3V VSB helpers
Change-Id: Ic93d78fce18c68d1d1bf3b537e8985a2532a8fcf
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/5901
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Move samsung/stumpy board towards generic romstage component and away
from poorly written hard-coded model specific Super I/O component. This
is an incremental step towards getting obj-level abstraction between
board and Super I/O.
Change-Id: I358c5abef85c2ffa1b7178025cde8834a35b0a51
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/5899
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
We now have common ite_*_*() functions for romstage and hence no longer
require the model specific portion of this superio support.
Change-Id: I30400abf27008a88072673075bba445f100d9ad3
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/5838
Tested-by: build bot (Jenkins)
Reviewed-by: Idwer Vollering <vidwer@gmail.com>
|
|
Drop it8712f_kill_watchdog() in favor of common ite_kill_watchdog()
introduced in commit rev:
a7d14a1 ite/common: Introduce common watchdog and 3.3V VSB helpers
Change-Id: I9fc4d3ee7992618b5b14e35166e848d6e1cffa8b
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/5837
Tested-by: build bot (Jenkins)
Reviewed-by: Idwer Vollering <vidwer@gmail.com>
|
|
Change-Id: Ib086cd567c926dd659f67900195f93262ceb50c3
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/5839
Tested-by: build bot (Jenkins)
Reviewed-by: Idwer Vollering <vidwer@gmail.com>
|
|
The Asus F2A85-M has IT8306E which is a stripped down version
of this SIO. Implement the PNP operations of the SIO.
Change-Id: Ibc4f3fafc3ffb1cd799948e63be01e6924b45d6c
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Reviewed-on: http://review.coreboot.org/4498
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Introduce the watchog and 3.3 VSB helper functions.
The IT8712F can be migrated to use those too. To be used
with IT8728F.
Change-Id: If21e99b6069c7222f0bc8eb7c7121fe119b8dfe1
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Reviewed-on: http://review.coreboot.org/5728
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Use proper include header in it8728f_hwm.c, fix format error.
The base of HWM block starts at offset +5.
Change-Id: I6855225b38bbcf5687d506bea9482c951d314684
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Reviewed-on: http://review.coreboot.org/5729
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
|
|
Change-Id: If7141112ea67071ee05c52f455c3b2496aa7e17e
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/5622
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
While backing out the empty pc80 keyboard struct we encountered some
special cases where chip.h is used for other purposes. Deal with these
cases.
Change-Id: Ib11a46cfd14d050d5daa213623b9d8a401c06410
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/5621
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
This is a empty struct that has propagated through the superio's & ec's
but really does nothing. Time to get rid of it before it adds yet more
cruft. However, since this touches many superio's at once we do this in
stages by first changing the function type to be a pure procedure.
Change-Id: Ibc732e676a9d4f0269114acabc92b15771d27ef2
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/5617
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Rudolf Marek <r.marek@assembler.cz>
|
|
Make use of the ITE common Super I/O framework and there-by removing any
hard coding of Super I/O base address.
Change-Id: I14af89d2727d7c6bac0f9840043c430726297429
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/5717
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Following the reasoning of:
cf7b498 superio/fintek/*: Factor out generic romstage component
Change-Id: I4c0a9a5a7786eb8fcb0c3ed6251c7fe9bbbadae7
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/5585
Tested-by: build bot (Jenkins)
Reviewed-by: Rudolf Marek <r.marek@assembler.cz>
|
|
Provide devicetree.cb RAMstage configuration of this superio component.
Change-Id: I376d2fb6dafc301cbc437518012f8c43b0af4be2
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/5668
Tested-by: build bot (Jenkins)
Reviewed-by: Rudolf Marek <r.marek@assembler.cz>
|
|
Following the reasoning of:
HASH superio/ite/it8705f: Remove poor implementation
Change-Id: Ic0722116b84acf4f3c3ef4b18b961a56f0f50718
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/5568
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
This super io support is poorly implemented and would not work for all
boards since it hardcodes values. Since there are no users of it, remove
for now pending a fresh reimplementation from scratch.
Change-Id: I818a9f4d2ab106b989824e49cee49d79acd6041a
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/5566
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Following the same reasoning as:
HASHHERE superio/ite/it8721f: Rewrite from hardcoded base addr
Removing hard coded magics and expose sio pnp api in romstage.
Change-Id: I27433cb1a84b3641a6110ecf6bd5021e00769aba
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/5565
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Rewrite early_serial.c implementation to honour a passed base address in
device_t, removing any hard coding of values. We also expose early sio
init functions as romstage symbols to avoid falsely #including
"early_serial.c" in romstage.c of board support.
Change-Id: I521b8f7cf85173345b90745c6f2ab66e25429f5d
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/5561
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Try to conform to some kind of standard/consensus for prototype
location. Correct headers while here.
Change-Id: Ie99b1801fa42ddefb9f25d54f326ba7131bd7089
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/5499
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
Change-Id: If723896cc31da75dbb3a63d5dc959764e96fded1
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/5139
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
This is the first of a series of patches to provide support
for a new mainboard, Gigabyte GA-B75M-D3V.
This patch provides early serial for the superio and has been
tested on this mainboard. The code is based on IT8718F superio.
Change-Id: I5636199b49314166ed3b81e60b41131964dd44ff
Signed-off-by: Damien Zammit <damien@zamaudio.com>
Reviewed-on: http://review.coreboot.org/3794
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Tested-by: build bot (Jenkins)
|
|
After removing the enter()/exit() functions for configuration mode,
most wrappers for our standard PnP functions just call the underlying
default implementation.
Remove those with a little cocci:
@ op_match @
identifier op;
identifier pnp_op =~ "^pnp_((alt_|)enable|(set|enable)_resources)$";
type device_t;
identifier dev;
@@
static void op(device_t dev) { pnp_op(dev); }
@@
identifier op_match.op;
@@
-op(...) {...}
/* Three rules to match the alignment, hmmp... */
@@
identifier op_match.op, op_match.pnp_op;
identifier ops;
@@
struct device_operations ops = {
- .set_resources = op,
+ .set_resources = pnp_op,
};
@@
identifier op_match.op, op_match.pnp_op;
identifier ops;
@@
struct device_operations ops = {
- .enable_resources = op,
+ .enable_resources = pnp_op,
};
@@
identifier op_match.op, op_match.pnp_op;
identifier ops;
@@
struct device_operations ops = {
- .enable = op,
+ .enable = pnp_op,
};
Change-Id: Idc0e52c7e3600a01f3b6a4e17763557b271b481e
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: http://review.coreboot.org/3483
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Find all the (ramstage) implementations of enter()/exit() functions
for the configuration state, register and call them through the new
struct pnp_mode_ops. As our standard PnP functions are aware of the
pnp_mode_ops, it's not necessary to call enter()/exit() around them
anymore.
Patch generated with the cocci below. It's not perfect. The movement
of the enter()/exit() calls is somehow fragile. So I checked the
remaining calls for sense, and changed some empty lines. Also a
duplicate insertion of pnp_conf_mode_ops had to be removed.
/* Try to find enter and exit functions by their outb() structure and
their usage around calls to our standard pnp functions: */
@ enter_match @
identifier enter;
identifier dev;
type device_t;
@@
void enter(device_t dev)
{
<...
outb(..., dev->path.pnp.port);
...>
}
@ exit_match @
identifier exit;
identifier dev;
type device_t;
@@
void exit(device_t dev)
{
<...
outb(..., dev->path.pnp.port);
...>
}
@ pnp_match @
identifier op;
identifier pnp_op =~ "^pnp_((alt_|)enable|(set|enable)_resources)$";
identifier enter_match.enter, exit_match.exit;
type device_t;
identifier dev;
@@
void op(device_t dev)
{
...
enter(dev);
...
pnp_op(dev);
...
exit(dev);
...
}
/* Now add enter/exit to a pnp_mode_ops structure: */
@ depends on pnp_match @
identifier enter_match.enter;
identifier exit_match.exit;
identifier ops;
@@
+static const struct pnp_mode_ops pnp_conf_mode_ops = {
+ .enter_conf_mode = enter,
+ .exit_conf_mode = exit,
+};
+
struct device_operations ops = {
...,
+ .ops_pnp_mode = &pnp_conf_mode_ops,
};
/* Match against the new structure as we change the code and the above
matches might not work anymore: */
@ mode_match @
identifier enter, exit, ops;
@@
struct pnp_mode_ops ops = {
.enter_conf_mode = enter,
.exit_conf_mode = exit,
};
/* Replace enter()/enter() calls with new standard calls (e.g.
pnp_enter_conf_mode()): */
@@
identifier mode_match.enter;
expression e;
@@
-enter(e)
+pnp_enter_conf_mode(e)
@@
identifier mode_match.exit;
expression e;
@@
-exit(e)
+pnp_exit_conf_mode(e)
/* If there are calls to standard PnP functions, (re)move the
enter()/exit() calls around them: */
@@
identifier pnp_op =~ "^pnp_((alt_|)enable|(set|enable)_resources)$";
expression e;
@@
-pnp_enter_conf_mode(e);
pnp_op(e);
+pnp_enter_conf_mode(e);
...
pnp_exit_conf_mode(e);
@@
identifier pnp_op =~ "^pnp_((alt_|)enable|(set|enable)_resources)$";
expression e;
@@
pnp_enter_conf_mode(e);
...
+pnp_exit_conf_mode(e);
pnp_op(e);
-pnp_exit_conf_mode(e);
@@
expression e;
@@
-pnp_enter_conf_mode(e);
-pnp_exit_conf_mode(e);
Change-Id: I5c04b0c6a8f01a30bc25fe195797c02e75b6c276
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: http://review.coreboot.org/3482
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
The current default implementation of pnp_enable() only disables devices
- if set so in the devicetree - but does not enable them. Enablement takes
place in pnp_enable_resources(). Yet, many PnP chips implement their own
version of pnp_enable() which also enables devices if set in the devicetree.
It's arguable, if enabling those devices makes sense, before they get
resources assigned. Maybe we can't write the resource registers if not,
who knows? The least we can do is providing a common implementation for
this behavior, and get rid of some code duplication.
Used the following cocci:
@@
expression e;
@@
+pnp_alt_enable(e);
-pnp_set_logical_device(e);
(
-pnp_set_enable(e, !!e->enabled);
|
-(e->enabled) ? pnp_set_enable(e, 1) : pnp_set_enable(e, 0);
|
-if (e->enabled) { pnp_set_enable(e, 1); }
-else { pnp_set_enable(e, 0); }
)
Change-Id: I8d695e8fcd3cf8b847b1aa99326b51a554700bc4
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: http://review.coreboot.org/3480
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Most PnP drivers align the initialization of their `device_operations`
with spaces. Unify this, so next autogenerated patches always match the
alignment.
Change-Id: I3f6baef6c8bb294c136354754125ea88c07a61a1
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: http://review.coreboot.org/3479
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Commit "romcc: Don't fail on function prototypes" (11a7db3b) [1]
made romcc not choke on function prototypes anymore. This
allows us to get rid of a lot of ifdefs guarding __ROMCC__ .
[1] http://review.coreboot.org/2424
Change-Id: Ib1be3b294e5b49f5101f2e02ee1473809109c8ac
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/3216
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Here's the great news: From now on you don't have to worry about
hitting the right io.h include anymore. Just forget about romcc_io.h
and use io.h instead. This cleanup has a number of advantages, like
you don't have to guard device/ includes for SMM and pre RAM
anymore. This allows to get rid of a number of ifdefs and will
generally make the code more readable and understandable.
Potentially in the future some of the code in the io.h __PRE_RAM__
path should move to device.h or other device/ includes instead,
but that's another incremental change.
Change-Id: I356f06110e2e355e9a5b4b08c132591f36fec7d9
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2872
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
In the file `COPYING` in the coreboot repository and upstream [1]
just one space is used.
The following command was used to convert all files.
$ git grep -l 'MA 02' | xargs sed -i 's/MA 02/MA 02/'
[1] http://www.gnu.org/licenses/gpl-2.0.txt
Change-Id: Ic956dab2820a9e2ccb7841cab66966ba168f305f
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2490
Tested-by: build bot (Jenkins)
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
|
|
Also deletes files not included in build:
src/southbridge/amd/cimx/sb700/chip_name.c
src/southbridge/amd/cimx/sb800/chip_name.c
src/southbridge/amd/cimx/sb900/chip_name.c
Change-Id: I2068e3859157b758ccea0ca91fa47d09a8639361
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1473
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Marc Jones <marcj303@gmail.com>
|
|
The name is derived directly from the device path.
Change-Id: If2053d14f0e38a5ee0159b47a66d45ff3dff649a
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1471
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
|
|
Change-Id: I8e80c22eb0f3cb68f2457be6b2e7894df60ed632
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/822
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Change-Id: Ib91889a374515d36a2b12b53aeb12b6ea6e22732
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/364
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
only the serial port is tested, keyboard/mouse are gonna
to be tested later, it may also need some more patches
to make it work completely.
Change-Id: Ie9464d01c5d5760ebc800b3cd15a4ab2bad2e09f
Signed-off-by: QingPei Wang <wangqingpei@gmail.com>
Reviewed-on: http://review.coreboot.org/204
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
|
|
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Acked-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6535 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
See discussion at
http://www.mail-archive.com/coreboot@coreboot.org/msg29394.html
config->com1, devicetree.cb cleanup and init_uart8250() removal
will follow once this patch is comitted
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
Updated to drop com1, com2.... from config structure and devicetree.cb
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6521 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Instead of enable the device the device gets disabled. However after some time the serial line gets back, most likely some "enable resources" might fix it.
I'm attaching patch which somewhat fixes the problem and changes the function to look same in all superio code. Some boards even did not convert the dev->enabled to 0,1 values.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6373 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Mostly done according to initial file creator.
Signed-off-by: Stefan Reinauer <stepan@coreboot.org>
Acked-by: Stefan Reinauer <stepan@coreboot.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6192 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
the prefix was introduced in the early v2 tree many years ago
because our old build system "newconfig" could not handle two files with
the same name in different paths like /path/to/usb.c and
/another/path/to/usb.c correctly. Only one of the files would end up
being compiled into the final image.
Since Kconfig (actually since shortly before we switched to Kconfig) we
don't suffer from that problem anymore. So we could drop the sb700_
prefix from all those filenames (or, the <componentname>_ prefix in general)
- makes it easier to fork off a new chipset
- makes it easier to diff against other chipsets
- storing redundant information in filenames seems wrong
Signed-off-by: <stepan@coresystems.de>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6150 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
- Random coding style, whitespace and cosmetic fixes.
- Consistently use the same spacing and 4-hexdigit port number format
in the pnp_dev_info[] arrays.
- Drop dead/unused code and less useful comments.
- Add missing "(C)" characters and copyright years.
- Shorten and simplify some code snippets.
- Use u8/u16/etc. everywhere.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6073 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
The pc_keyboard_init() function no longer takes any base addresses
since r5152 (passed in via res0/res1 variables previously), so drop them.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6063 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
- it8661f_enable_serial() is now in the usual format, using pnp_* functions.
- Factor out pnp_enter_ext_func_mode()/pnp_exit_ext_func_mode().
- Factor out it8661f_set_clkin() to set the CLKIN to 24/48MHz.
- Factor out it8661f_enable_logical_devices(), might not be needed though.
We leave it here until it's confirmed on hardware that it's not needed.
- Move some #defines to it8661f.h.
- Drop no longer used it8661f_sio_write().
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6053 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6049 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
- Drop some of the less useful / outdated / duplicated comments.
- Simplify and streamline some code to look like the other Super I/Os.
- Use u8/16/etc. everywhere.
- ITE IT8718F: Add missing GPIO LDN.
- Add missing braces around SIO_DATA #defines, potential bug even.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6047 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
at the same time let the user specify sources instead
of object files:
- objs becomes ramstage-srcs
- initobjs becomes romstage-srcs
- driver becomes driver-srcs
- smmobj becomes smm-srcs
The user servicable parts are named accordingly:
ramstage-y, romstage-y, driver-y, smm-y
Also, the object file names are properly renamed now, using
.ramstage.o, .romstage.o, .driver.o, .smm.o suffixes consistently.
Remove stubbed out via/epia-m700 dsdt/ssdt files - they didn't
easily fit in the build system and aren't useful anyway.
Signed-off-by: Patrick Georgi <patrick.georgi@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coreystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5886 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
After lots of testing, the SuperIO LDN 7, register 0xEF is the key to the
problem. This patch adds a function which stops dual bios mainboards from
rebooting, when called.
Signed-off-by: Wang Qing Pei <wangqingpei@gmail.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5697 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
This fixes serial console on GIGABYTE GA-6BXE.
Signed-off-by: Anders Jenbo <anders@jenbo.dk>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5555 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
guards.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5520 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5492 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5449 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
