summaryrefslogtreecommitdiff
path: root/src/southbridge
AgeCommit message (Collapse)Author
2013-11-25lynxpoint: Enable USB clock gating, late setup, and sleep prepDuncan Laurie
Both EHCI and XHCI controllers have additional setup steps that are not part of the PEI reference code so they need to be done later. Both controllers also have specific clock gating setup requirements that are now implemented. Additionally they both have specific requirements when entering sleep states. XHCI needs something in S3/S4/S5 and EHCI only has steps for S4/S5 entry. Change-Id: Ic62cbc8b6255455e56b72dd5d52e27a311999330 Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: https://gerrit.chromium.org/gerrit/57033 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: http://review.coreboot.org/4217 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-11-25lynxpoint: Add ACPI Method to enable GPIO as wake sourceDuncan Laurie
This is an LPT-LP specific method that will enable a specific GPIO as an ACPI SCI wake source. It can be used by a device _DSW method to enable a pin that is otherwise not configured to generate SCI at runtime. It will set: - GPIO owner to ACPI - GPIO route to SCI - GPIO config to GPIO, Input, Inverted Also clean up and remove ACPI field definitions that are unused and/or incorrect. Change-Id: I14acc2de50e6200f61c2898a7bd1252400e0f0be Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: https://gerrit.chromium.org/gerrit/56621 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: http://review.coreboot.org/4189 Reviewed-by: Ronald G. Minnich <rminnich@gmail.com> Tested-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-11-25lynxpoint: Enable extra 16 IOAPIC entries for GPIO PIRQDuncan Laurie
LynxPoint-LP has an additional 16 entries in the IOAPIC that can be assigned to specific GPIOs when they are configured as PIRQ. The maximum redirection entries field in the IOAPIC needs to be set to 0x27 when this is enabled. Additionally specific GPIOs need to be routed to PIRQ so they interrupt via the IOAPIC instead of the GPIO IRQ 14/15. Change-Id: Ie587e1d203422ff6fb7fc5056d20a5ae66720991 Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: https://gerrit.chromium.org/gerrit/56620 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: http://review.coreboot.org/4203 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-11-25lynxpoint: fix mem corruption during ssdt2 genAaron Durbin
The ssdt2 generation code was calling acpigen_patch_len(). However, none of the entries had AML object lengths that needed patching. That resulted in the following message: ASSERTION FAILED: file 'src/arch/x86/boot/acpigen.c',  line 52 Additionally, this caused an errant write to a memory address whose value was in the variable ltop. This was the 0 address. Change-Id: I44abf5a4e4225220575aee6b5c9bb6b0be093a28 Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: https://gerrit.chromium.org/gerrit/56299 Reviewed-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-by: Stefan Reinauer <reinauer@google.com> Reviewed-on: http://review.coreboot.org/4182 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-11-25lynxpoint: Fix XHCI controller device in ACPIDuncan Laurie
The ACPI code was defining two EHCI controllers and ignoring the XHCI controller. This changes the second EHCI controller to be XHCI instead and changes the wake resource to indicate S3 and not S4. cat /proc/acpi/wakeup Device S-state Status Sysfs node HDEF S4 *disabled pci:0000:00:1b.0 EHCI S3 *enabled pci:0000:00:1d.0 XHCI S3 *enabled pci:0000:00:14.0 Change-Id: If28775e6ef8608c22c85ca91d91d1f598ec7755d Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: https://gerrit.chromium.org/gerrit/56263 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: http://review.coreboot.org/4181 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-11-25lynxpoint: Enable SerialIO clock in PCI modeDuncan Laurie
The clock gating register at offset 0x800 is managed by the clock driver in the kernel when the devices are in ACPI mode. When in PCI mode we should force enable the clock here. When in ACPI mode or the device is disabled it should be put in D3Hot state. > i2cdetect -y -r 10 0 1 2 3 4 5 6 7 8 9 a b c d e f 00: -- -- -- -- -- -- -- -- -- -- -- -- -- 10: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 20: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 30: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 40: -- -- -- -- 44 -- -- -- -- -- -- -- -- -- -- -- 50: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 60: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 70: -- -- -- -- -- -- -- -- Change-Id: Ib93ffd41bf36386d5ce63bfc0ae6597f3e23bc48 Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: https://gerrit.chromium.org/gerrit/56122 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: http://review.coreboot.org/4180 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-11-25slippy: Enable EC SMIDuncan Laurie
Enable GPIO SMI for GPIO34 and set it as inverted so it is only generated when it is raised by the EC. 1) ec console command: lidopen 2) wait until booted to developer screen 3) ec console command: lidclose 4) ensure system turns off Change-Id: I7d50f171f3f4539c7c264103d1ffc7c5d0f1c7ba Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: https://gerrit.chromium.org/gerrit/56052 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: http://review.coreboot.org/4177 Tested-by: build bot (Jenkins) Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
2013-11-25lynxpoint: update azalia device idsAaron Durbin
The vendor ids were never updated to reflect LynxPoint's device ids. Therefore, none of the initialization was being ran. Fix this. Change-Id: Ic6ec00c9fb1cbcb6087fd89b0acff3d83294ac6a Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: https://gerrit.chromium.org/gerrit/55821 Reviewed-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: http://review.coreboot.org/4173 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-11-25lynxpoint: Change SerialIO device enable reporting to ACPIDuncan Laurie
In order to report whether coreboot enabled a SerialIO device in ACPI mode we had been relying on reading NVS in the _STA method for the SerialIO device. The ACPI _STA method has restrictions on what it can access and is unable to access OperationRegions outside its scope which means it should not be trying to read NVS. This change adds a new SSDT to the ACPI tables and fills it with constants that indicate whether or not a device is enabled in ACPI mode. The ACPI code is changed to read these variables from the SSDT and use that instead of trying to query a variable in NVS. Attempt to use lpt-clk driver to probe the device clocks for SerialIO devices and see that the kernel does not complain about accessing the GNVS region. Change-Id: I8538bee4390daed4ecca679496ab0cb313f174ce Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: https://gerrit.chromium.org/gerrit/51369 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: http://review.coreboot.org/4170 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-11-25slippy: Minor vboot related fixesDuncan Laurie
- Disable EC software sync for now - Report correct EC active firmware mode - Force enable developer mode by default - Set up PCH generic decode regions in romstage - Pass the oprom_is_loaded flag into vboot handoff data Change-Id: Ib7ab35e6897c19455cbeecba88160ae830ea7984 Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: https://gerrit.chromium.org/gerrit/51155 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: http://review.coreboot.org/4169 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-11-25lynxpoint: Expose ACPI Device for LP GPIO controllerDuncan Laurie
In order to probe the gpio-lynxpoint kernel driver the LP GPIO controller needs to be exposed as a specific ACPI device. This also allows the resources to be exposed to the OS via this device instead of the catch-all LPC device. Ensure the driver loads at boot: gpiochip_find_base: found new base at 162 gpiochip_add: registered GPIOs 162 to 255 on device: INT33C7:00 Also ensure the driver is visible in sysfs: $ cat /sys/devices/platform/INT33C7:00/gpio/gpiochip162/label INT33C7:00 Change-Id: I9f79c008f88da9b67ed1cdfdb9d3a581ce8f05ff Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: https://gerrit.chromium.org/gerrit/50215 Reviewed-on: http://review.coreboot.org/4158 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-11-25lynxpoint: Move ME lock down to ramstageDuncan Laurie
Now that we have RW ramstage we don't need to have the management engine lock down step done in a final SMM. ME: mkhi_end_of_post ME: END OF POST message successful (0) PCI: 00:16.0: Disabling device Change-Id: I9db4e72e38be58cc875c1622a966d8fcacc83280 Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: https://gerrit.chromium.org/gerrit/49757 Reviewed-on: http://review.coreboot.org/4153 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-11-25lynxpoint: Add missing ME MBP entriesDuncan Laurie
There were two undefined MBP types that are now defined. These include NFC status and some interesting timing data. ME: Wake Event to ME Reset: 6 ms ME: ME Reset to Platform Reset: 7 ms ME: Platform Reset to CPU Reset: 51 ms Change-Id: I67bf1f303f3c32497041e64c40eb9ccb6a63d88a Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: https://gerrit.chromium.org/gerrit/49756 Reviewed-on: http://review.coreboot.org/4152 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-11-25lynxpoint: export mem console pointer in ACPIAaron Durbin
Instead of having an OS re-parse cbmem book-keeping records for the cbmem allocator just to get the console buffer export the pointer to the memory console directly in a field named 'CBMC'. This field lives in the GNVS table. Change-Id: Ief0c4da7b18df66feb9c816c9f4abdf5a72bd3a4 Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: https://gerrit.chromium.org/gerrit/49764 Reviewed-by: Stefan Reinauer <reinauer@chromium.org> Reviewed-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: http://review.coreboot.org/4149 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-11-25lynxpoint: Updates to power management and clock gatingDuncan Laurie
Slight tweaks found when looking at latest ref code when investigating package C-state issues. A few bits in the clock gating register don't match the documentation and are also cleaned up. Change-Id: I36ced7280c160b114c70b2eeafc8b24813ff2f6a Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: https://gerrit.chromium.org/gerrit/49330 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: http://review.coreboot.org/4142 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-11-25Support for Ibexpeak southbridgeVladimir Serbinenko
Part of X201 port. Change-Id: If17d707004aba9f08459dbd8f3a146fa3c076aa9 Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com> Reviewed-on: http://review.coreboot.org/4052 Reviewed-by: Ronald G. Minnich <rminnich@gmail.com> Tested-by: build bot (Jenkins)
2013-11-24haswell: Configure PCH power sharing for ULTDuncan Laurie
This reads PCH power levels via PCODE mailbox and writes the values into the PMSYNC registers as indicated in the BWG. Change-Id: Iddcdef9b7deb6365f874f629599d1f7376c9a190 Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: https://gerrit.chromium.org/gerrit/49329 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: http://review.coreboot.org/4143 Tested-by: build bot (Jenkins) Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
2013-11-24lynxpoint: Add a function to set an individual GPIODuncan Laurie
This will be used in a later commit to do some specific power sequencing. Change-Id: Id7f033bb80aed915c2498ea910cb3ac7290da37f Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: https://gerrit.chromium.org/gerrit/48947 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: http://review.coreboot.org/4137 Tested-by: build bot (Jenkins) Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
2013-11-24lynxpoint: Rework LP GPIO handlingDuncan Laurie
This adds some macros for the common GPIO defines and drops the gpio number definition from each entry. The end result is much easier to read. The wtm2 mainboard gpio list is modified to use this. Also fix a bug in the LP version of get_gpio() that was always returning zero due to a miscompare. Change-Id: I143e5aee412af1eda84e35f8026f31cf13df508e Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: https://gerrit.chromium.org/gerrit/48946 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: http://review.coreboot.org/4138 Tested-by: build bot (Jenkins) Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
2013-11-24smi: Update mainboard_smi_gpi() to have 32bit argumentDuncan Laurie
With the LynxPoint chipset there are more than 16 possible GPIOs that can trigger an SMI so we need a mainboard handler that can support this. There are only a handful of users of this function so just change them all to use the new prototype. Change-Id: I3d96da0397d6584f713fcf6003054b25c1c92939 Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: https://gerrit.chromium.org/gerrit/49530 Reviewed-by: Stefan Reinauer <reinauer@google.com> Reviewed-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: http://review.coreboot.org/4145 Tested-by: build bot (Jenkins) Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
2013-11-24slippy: Prepare LPC IO decode ranges for ECDuncan Laurie
- 0x200-0x208 for host command window - 0x800-0x8ff for host command arguments and parameters - 0x900-0x9ff for exported EC memory map Change-Id: I064b969843ef0d3c602793d1cb3d82715775c05e Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: https://gerrit.chromium.org/gerrit/49755 Reviewed-on: http://review.coreboot.org/4151 Tested-by: build bot (Jenkins) Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
2013-11-24dmp/vortex86ex: Move DMP specific POST code defines into one fileAndrew Wu
Move into src/cpu/dmp/dmp_post_code.h Change-Id: If9f4d842f352eb41618e71f49a226d3cc4ad0b46 Signed-off-by: Andrew Wu <arw@dmp.com.tw> Reviewed-on: http://review.coreboot.org/3989 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-11-12AMD Hudson: Move function s3_resume_init_data to southbridgeZheng Bao
Besides the AGESA static settings, the settings in mainboard/buildOpt.c also change the final configuration. We need to make sure the settings in FchParam in resume stage are the same as they were in cold boot stage, otherwise the board can not wake up more than once. Tested on AMD/Olive Hill, AMD/Parmer and ASRock/imb-a180. (USB keyboard doesn't work when board wakes up. It is not introduced by this patch. It needs more debugging.) Change-Id: I5a5e5502080e358ffc3577dc6a40bb762844d998 Signed-off-by: Zheng Bao <zheng.bao@amd.com> Signed-off-by: Zheng Bao <fishbaozi@gmail.com> Reviewed-on: http://review.coreboot.org/3932 Tested-by: build bot (Jenkins) Reviewed-by: Rudolf Marek <r.marek@assembler.cz>
2013-11-05southbridge/via/vt8237r/ctrl.c: Remove set but unused variable `regm3`Paul Menzel
Change-Id: I6bb652419a54b7b7190e417346581f38335425ae Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-on: http://review.coreboot.org/3985 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org> Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-10-30southbridge/intel/i82801ix/lpc.c: Remove unused variable `dummy`Paul Menzel
Removing `-Wno-unused-but-set-variable` from `CFLAGS` the build for QEMU Q35 and Roda RK9, both using the Intel 82801Ix southbridge, fail with the following error. src/southbridge/intel/i82801ix/lpc.c: In function 'i82801ix_enable_apic': src/southbridge/intel/i82801ix/lpc.c:45:5: error: variable 'dummy' set but not used [-Werror=unused-but-set-variable] cc1: all warnings being treated as errors Removing `dummy` should be safe as GCC probably optimizes it away before anyway. That no dummy variable is used for an RCBA [1] access in Intel Lynx Point supports that this can be dropped safely. [1] root complex base address [2] src/southbridge/intel/lynxpoint/early_pch.c Change-Id: I1c138a3498228dbd025f68d5e6af0acc29ed3460 Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-on: http://review.coreboot.org/3982 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@google.com>
2013-10-22vortex86ex: Defer checking PS/2 keyboard controller system flagAndrew Wu
Don't check keyboard controller system flag until before calling pc_keyboard_init(). This makes waiting time shorter. Change-Id: I2cdb533a5b25575e1717434533a60decf748f6d8 Signed-off-by: Andrew Wu <arw@dmp.com.tw> Reviewed-on: http://review.coreboot.org/3958 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-10-22usbdebug: Fix boards without EARLY_CBMEM_INITKyösti Mälkki
The main usbdebug file lib/usbdebug.c was removed from romstage build with commit f8bf5a10 but the chipset-specific parts were not, leading to unresolved symbol errors for AMD platforms. Add a silent Kconfig variable USBDEBUG_IN_ROMSTAGE for convenient use of this feature. Change-Id: I0cd3fccf2612cf08497aa5c3750c89bf43ff69be Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: http://review.coreboot.org/3983 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@google.com>
2013-10-15intel/i82371: Remove HAVE_ACPI_RESUMEKyösti Mälkki
This is needed to apply a rule that get_top_of_ram() in romstage is required to select HAVE_ACPI_RESUME, otherwise chipset/board has no means to backup low memory to CBMEM on s3 resume. Only board affected is asus/p2b. Change-Id: Ia5cbf4e5e40af25f52a19de584d8bc5370487154 Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: http://review.coreboot.org/3971 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@google.com>
2013-10-14ck804: hide IOAPIC base address in PCI_BASE_ADDRESS_1Jonathan A. Kollasch
Linux unhelpfully "fixes" the value in PCI_BASE_ADDRESS_1 when it is 0xfec00000 (that is, outside the range of bus 0 address space). This causes IOAPIC interrupts to fail to work under Linux. This issue was originally unnoticed by me when testing as sanity checking such as this is not done by NetBSD. Hiding the IOAPIC BAR is done by the OEM BIOS on the ck804 boards I've checked. Change-Id: I736db163750f709d68c988fac075597a50b29ab7 Signed-off-by: Jonathan A. Kollasch <jakllsch@kollasch.net> Reviewed-on: http://review.coreboot.org/3963 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-10-14ck804: obtain stored IOAPIC address from allocator instead of registerJonathan A. Kollasch
Change-Id: Ibdd438455a545aa9266b0fd893d5ff27124ab22c Signed-off-by: Jonathan A. Kollasch <jakllsch@kollasch.net> Reviewed-on: http://review.coreboot.org/3961 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-10-13dmp/vortex86ex: Initialize PS/2 keyboard.Andrew Wu
Call pc_keyboard_init function in southbridge. It makes PS/2 keyboard work in coreinfo payload. Change-Id: Idb79f87b09eeeade94e966fb8769dec7578e2cf5 Signed-off-by: Andrew Wu <arw@dmp.com.tw> Reviewed-on: http://review.coreboot.org/3957 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Jonathan A. Kollasch <jakllsch@kollasch.net> Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-10-13ck804 lpc: use PCI_BASE_ADDRESS_1 instead of 0x14Jonathan A. Kollasch
Change-Id: I752a4a890e1f610651a2c688cf42350ce8e9deaa Signed-off-by: Jonathan A. Kollasch <jakllsch@kollasch.net> Reviewed-on: http://review.coreboot.org/3962 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
2013-10-01qemu: q35: avoid address conflictGerd Hoffmann
Qemu has the fw_cfg interface at 0x510, which conflicts with power management base address in coreboot. Move the pmbase to a non-conflicting address. No need to worry about speedstep, it is not supported by qemu and isn't enabled in the qemu config. Change-Id: I3e87d8301988028ca0ea7d96c08b4e26ac15a7c2 Signed-off-by: Gerd Hoffmann <kraxel@redhat.com> Reviewed-on: http://review.coreboot.org/3938 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-09-25usbdebug AMD: Add choice of EHCI controllerKyösti Mälkki
Chipsets sb700 and sb800/hudson have more than one USB EHCI controller, implement the selection logic using already existing Kconfig option. Change-Id: I9e0df1669d73863c95c36a3a7fee40d58f6f097e Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: http://review.coreboot.org/3928 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-09-24southbridge/cimx/sb900: Rename headers to match sb700 & sb800Corey Osgood
Northbridge code includes these headers, so they all need to have the same name to allow different combinations of northbridge and southbridge. This changes the sb900 names to match sb700 & sb800, and points agesa/family12 and amd/torpedo to the new file names. Change-Id: I7a654ce9ae591a636a56177f64fb8cb953b4b04f Signed-off-by: Corey Osgood <corey.osgood@gmail.com> Reviewed-on: http://review.coreboot.org/3825 Tested-by: build bot (Jenkins) Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
2013-09-21timestamps intel: Move timestamp scratchpad to chipsetKyösti Mälkki
This retrieves back the value stored with store_initial_timestamp() in the bootblock for southbridge. Change-Id: I377c823706c33ed65af023d20d2e4323edd31199 Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: http://review.coreboot.org/3908 Tested-by: build bot (Jenkins) Reviewed-by: Patrick Georgi <patrick@georgi-clan.de> Reviewed-by: Aaron Durbin <adurbin@google.com>
2013-09-17Fix whitespace leaked into treeKyösti Mälkki
Clean whitespace errors that have gotten past lint-stable-003-whitespace and gerrit review. Change-Id: Id76fc68e9d32d1b2b672d519b75cdc80cc4f1ad9 Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: http://review.coreboot.org/3920 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Bruce Griffith <Bruce.Griffith@se-eng.com> Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-09-11CBMEM: Backup top_of_ram instead of cbmem_tocKyösti Mälkki
AMD northbridges have a complex way to resolve top_of_ram. Once it is resolved, it is stored in NVRAM to be used on resume. TODO: Redesign these get_top_of_ram() functions from scratch. Change-Id: I3cceb7e9b8b07620dacf138e99f98dc818c65341 Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: http://review.coreboot.org/3557 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@google.com>
2013-09-10intel/i945 intel/i82801gx: remove explicit pcie config accessesKyösti Mälkki
Now that MMCONF_SUPPORT_DEFAULT is enabled by default remove the pcie explicit accesses. The default config accesses use MMIO. Change-Id: I46e69154cf576ddb642c34b6dd2bc0d27cc19b7e Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: http://review.coreboot.org/3811 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@google.com>
2013-09-10intel/i82801ix: remove explicit pcie config accessesKyösti Mälkki
Now that MMCONF_SUPPORT_DEFAULT is enabled by default remove the pcie explicit accesses. The default config accesses use MMIO. Change-Id: Ie6776b04ca0ddb89a0843c947f358db267ac4a70 Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: http://review.coreboot.org/3809 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@google.com> Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
2013-09-06usbdebug: Fixes for LynxPoint LPKyösti Mälkki
Keep the EHCI BAR unchanged to keep usbdebug working. Change-Id: I7fe0eed24a66cb5058b49ee3fc0350d91089ed7a Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: http://review.coreboot.org/3477 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@google.com>
2013-08-29intel usbdebug: Add choice of EHCI controllerKyösti Mälkki
Add option to choose one of the EHCI controllers in recent intel chipsets for usbdebug use. Since EHCI controller function changes from 0:1d.7 to 0:1d.0 in rcba_config() for some mainboards, check the PCI class code for match. Change-Id: I18a78bf875427c163c857c6f0888935c1d2a58d4 Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: http://review.coreboot.org/3440 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@google.com>
2013-08-29usbdebug: Support choice of EHCI controllerKyösti Mälkki
Nowadays, chipsets or boards do not only have one USB port with the capabilities of a debug port but several ones. Some of these ports are easier accessible than others, so making them configurable is also necessary. This change adds infrastructure to switch between EHCI controllers, but does not implement it for any chipset. Change-Id: I079643870104fbc64091a54e1bfd56ad24422c9f Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: http://review.coreboot.org/3438 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@google.com>
2013-08-29usbdebug: Change debug port scanningKyösti Mälkki
On AMD platforms, setting of USBDEBUG_DEFAULT_PORT=0 tries to scan all physical ports one after other in incrementing order. To avoid possible problems with other USB devices, one can select the port number here and bypass the scan. Intel platforms can communicate with usbdebug dongle on one physical port only, and this option makes no difference there. Change-Id: I45be6cc3aa91b74650eda2d444c9fcad39d58897 Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: http://review.coreboot.org/3872 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@google.com>
2013-08-27AMD f16kb: use AZ_PIN in Kconfig to customize AZALIA_PIN in YangtzeWANG Siyuan
src/southbridge/amd/agesa/hudson/Kconfig config default value, mainboard Kconfig config value for specific mainboard. bit 1,0 - pin 0 bit 3,2 - pin 1 bit 5,4 - pin 2 bit 7,6 - pin 3 Change-Id: I54a87cf734685515a3e1850838ca7d94387172ce Signed-off-by: WANG Siyuan <SiYuan.Wang@amd.com> Signed-off-by: WANG Siyuan <wangsiyuanbuaa@gmail.com> Reviewed-on: http://review.coreboot.org/3879 Tested-by: build bot (Jenkins) Reviewed-by: Bruce Griffith <Bruce.Griffith@se-eng.com> Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
2013-08-24usbdebug: Change reference to EHCI BARKyösti Mälkki
Change the defines, as follow-up patch will replace use of constant CONFIG_EHCI_BAR. Change-Id: I44ff77cb7a2826f3b43d8d46440fd4482a29d18c Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: http://review.coreboot.org/3875 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@google.com>
2013-08-24Add pci_devfn_t and use with __SIMPLE_DEVICE__Kyösti Mälkki
Declare the functions that may be used in both romstage and ramstage with simple device model. This will later allow to define PCI access functions for ramstage using the inlined functions from romstage. Change-Id: I32ff622883ceee4628e6b1b01023b970e379113f Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: http://review.coreboot.org/3508 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@google.com>
2013-08-23usbdebug: Do not support logging from SMMKyösti Mälkki
Letting SMI handler touch EHCI controller is an excellent source of USB problems. Remove usbdebug entirely from SMM. It may be possible to make usbdebug console work from SMM after hard work and coordination with payloads and even OS drivers. But we are not there. Change-Id: Id50586758ee06e8d76e682dc6f64f756ab5b79f5 Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: http://review.coreboot.org/3858 Reviewed-by: Patrick Georgi <patrick@georgi-clan.de> Tested-by: build bot (Jenkins)
2013-08-16Correct spelling of shadow, setting and memoryPaul Menzel
Change-Id: Ic7d793754a8b59623b49b7a88c09b5c6b6ef2cf0 Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-on: http://review.coreboot.org/3768 Tested-by: build bot (Jenkins) Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
2013-08-16AMD Southbridge CS5536: make use of #include <device/smbus_def.h>Christian Gmeiner
Change-Id: Ia2dff49d3e2b086546785d992f2d92bcf4d1ef1c Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com> Reviewed-on: http://review.coreboot.org/3376 Tested-by: build bot (Jenkins) Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
2013-08-15AMD Fam16: Add OSC method to PCI0Mike Loptien
The _OSC method is used to tell the OS what capabilities it can take control over from the firmware. This method is described in chapter 6.2.9 of the ACPI spec v3.0. The method takes 4 inputs (UUID, Rev ID, Input Count, and Capabilities Buffer) and returns a Capabilites Buffer the same size as the input Buffer. This Buffer is generally 3 Dwords long consisting of an Errors Dword, a Supported Capabilities Dword, and a Control Dword. The OS will request control of certain capabilities and the firmware must grant or deny control of those features. We do not want to have control over anything so let the OS control as much as it can. The _OSC method is required for PCIe devices. During Linux boot, an error is logged to dmesg if _OSC is not found. Change-Id: Icf6e7a82284d03d23fd30ee7b7db17754e988c9a Signed-off-by: Mike Loptien <mike.loptien@se-eng.com> Reviewed-on: http://review.coreboot.org/3823 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2013-08-15AMD Fam16: Add secondary bus number to CRES methodMike Loptien
Adding the 'WordBusNumber' macro to the PCI0 CRES ResourceTemplate in the AMD FCH ACPI code. This sets up the bus number for the PCI0 device and the secondary bus number in the CRS method. This change came in response to a 'dmesg' error which states: '[FIRMWARE BUG]: ACPI: no secondary bus range in _CRS' By adding the 'WordBusNumber' macro, ACPI can set up a valid range for the PCIe downstream busses, thereby relieving the Linux kernel from "guessing" the valid range based off _BBN or assuming [0-0xFF]. The Linux kernel code that checks this bus range is in `drivers/acpi/pci_root.c`. PCI busses can have up to 256 secondary busses connected to them via a PCI-PCI bridge. However, these busses do not have to be sequentially numbered, so leaving out a section of the range (eg. allowing [0-0x7F]) will unnecessarily restrict the downstream busses. Change-Id: Ib2d36f69a26b715798ef1ea17deb0905fa0cad87 Signed-off-by: Mike Loptien <mike.loptien@se-eng.com> Reviewed-on: http://review.coreboot.org/3822 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2013-08-15AMD Kabini: Split DSDT into common sectionsMike Loptien
Split the Family16 (Kabini) DSDT file into logical regions. Olive Hill is the only mainboard and Kabini is the only NB/CPU currently using Family16 AGESA code. Change-Id: I9ef9a7245d14c59f664fc768d0ffa92ef5db7484 Signed-off-by: Mike Loptien <mike.loptien@se-eng.com> Reviewed-on: http://review.coreboot.org/3821 Tested-by: build bot (Jenkins)
2013-08-13dmp/vortex86ex: Initialize Reatek ALC262 audio codecAndrew Wu
Hook this up into the DMP Vortex86EX. Before under Windows XP the microphone did not work. With the new logic it does. Now line-in,line-out and microphone all work. The verb data table is generated by Realtek. Change-Id: I1bcef898a15547c86c12c4b52ce0069d13e23c84 Signed-off-by: Andrew Wu <arw@dmp.com.tw> Reviewed-on: http://review.coreboot.org/3855 Tested-by: build bot (Jenkins) Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
2013-08-13Fix some wait_for_valid functions return value from 1 to -1.Andrew Wu
codec_init expects wait_for_valid returns -1 for timeout, not 1. Change-Id: I0f2a3ebb1934d0adaf13765434526bbc9efca9a3 Signed-off-by: Andrew Wu <arw@dmp.com.tw> Reviewed-on: http://review.coreboot.org/3843 Tested-by: build bot (Jenkins) Reviewed-by: Martin Roth <martin.roth@se-eng.com> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-08-10usbdebug: Fix AMD cimx/sb700 cimx/sb800Kyösti Mälkki
These Kconfig entries were forgotten from the commit that re-enabled usbdebug for these southbridges. Change-Id: Ia17f1dd3340408da7c033c2c949404d2636bed44 Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: http://review.coreboot.org/3849 Tested-by: build bot (Jenkins) Reviewed-by: Marc Jones <marc.jones@se-eng.com>
2013-08-09intel/sandybridge intel/bd82x6x: remove explicit pcie config accessesKyösti Mälkki
Now that MMCONF_SUPPORT_DEFAULT is enabled by default remove the pcie explicit accesses. The default config accesses use MMIO. Change-Id: I58c4b021ac87a035ac2ec2b6b110b75e6d263ab4 Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: http://review.coreboot.org/3810 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@google.com>
2013-08-08ASUS F2A85-M: Split DSDT into common sections (as per Parmer)Kimarie Hoot
Rearranged the F2A85-M DSDT file to match the functionality found on Parmer. As with the Parmer implementation, the F2A85-M dsdt.asl file in the mainboard directory contains only #include references to the appropriate files. As with Parmer, some include files have no content but are left as a template for other platforms and as placeholders for completing the ACPI implementation for F2A85-M. Change-Id: Ic72cb6004538ca9d9f79826b9b3c8d6aeb25017c Signed-off-by: Kimarie Hoot <kimarie.hoot@se-eng.com> Reviewed-on: http://review.coreboot.org/3805 Tested-by: build bot (Jenkins) Reviewed-by: Martin Roth <martin@se-eng.com>
2013-08-07usbdebug: Support AMD cimx/sb700 cimx/sb800 once againKyösti Mälkki
Support code for sb700 and sb800 existed already, but Kconfig and compile-time issues prevented from enabling USBDEBUG for boards with the affected AMD southbridges. Change-Id: I49e955fcc6e54927320b9dc7f62ea00c55c3cedf Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: http://review.coreboot.org/3439 Tested-by: build bot (Jenkins) Reviewed-by: Martin Roth <martin.roth@se-eng.com>
2013-08-07usbdebug: Use __SIMPLE_DEVICE__ on early enableKyösti Mälkki
With USBDEBUG selected, the file is built for both romstage and ramstage. For the ramstage build, we need to explicitly use the simple PCI config operations without devicetree. Change-Id: I2de8d9c77bb458ba797c3aac9e2cd0d653e06684 Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: http://review.coreboot.org/3437 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@google.com>
2013-08-05AMD Hudson/Yangtze: Enable support for SATA port multipliersBruce Griffith
This patch sets a bit in the Yangtze southbridge to enable the extra protocol necessary to handle port multiplier chips. This has been turned on during most of Kabini development without any notable impact. Olive Hill has an optional daughter board that incorporates Silicon Image Steel Vines chips. This change has been tested with and without the daughter board. This change can be regression tested using any Hudson-based motherboard, although it has no impact on boards with discreet Hudson/Bolton southbridges. This was tested for impact on SATA performance in the absence of a port multiplier using the IOZone benchmarks within the Phoronix Test Suite. A SATA 3 hard drive (6.0 Gbps) and an SSD were connected to the ports on Olive Hill without using the port multiplier card. The test results contained more run-to-run variation within the same configuration than was seen in the aggregate results comparing the interface with and without the port multiplier protocol additions. In other words, the test had less accuracy than the impact caused by turning on port multiplier support. Change-Id: Ie87873b093f3e2a6a5c83b96ccb6c898d3e25f72 Signed-off-by: Bruce Griffith <bruce.griffith@se-eng.com> Reviewed-by: Martin Roth <martin.roth@se-eng.com> Reviewed-by: Dave Frodin <dave.frodin@se-eng.com> Reviewed-on: http://review.coreboot.org/3808 Tested-by: build bot (Jenkins)
2013-08-05AMD Kabini: Modify Hudson southbridge to support new AMD processorSiyuan Wang
Yangtze uses Hudson AGESA wrapper code but has some changes. The changes are necessary and have no effects on Hudson. Change-Id: Iada90d34fdc2025bd14f566488ee12810a28ac0d Signed-off-by: Siyuan Wang <SiYuan.Wang@amd.com> Signed-off-by: Siyuan Wang <wangsiyuanbuaa@gmail.com> Signed-off-by: Bruce Griffith <Bruce.Griffith@se-eng.com> Reviewed-by: Dave Frodin <dave.frodin@se-eng.com> Tested-by: Bruce Griffith <bruce.griffith@se-eng.com> Reviewed-on: http://review.coreboot.org/3783 Tested-by: build bot (Jenkins) Reviewed-by: Martin Roth <martin.roth@se-eng.com>
2013-08-02Remove unnecessary space characters.Andrew Wu
Change-Id: I4ed9329126b216eb4ae58355672603ce79a6d4ef Signed-off-by: Andrew Wu <arw@dmp.com.tw> Reviewed-on: http://review.coreboot.org/3847 Tested-by: build bot (Jenkins) Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
2013-08-01intel/lynxpoint: remove explicit pcie config accessesKyösti Mälkki
Now that MMCONF_SUPPORT_DEFAULT is enabled by default remove the pcie explicit accesses. The default config accesses use MMIO. Change-Id: I71923790aa03e51db01ae3a4745e1c44556d281f Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: http://review.coreboot.org/3812 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@google.com>
2013-08-01Add directive __SIMPLE_DEVICE__Kyösti Mälkki
The tests for __PRE_RAM__ or __SMM__ were repeatedly used for detection if dev->ops in the devicetree are not available and simple device model functions need be used. If a source file build for ramstage had __PRE_RAM__ inserted at the beginning, the struct device would no longer match the allocation the object had taken. This problem is fixed by replacing such cases with explicit __SIMPLE_DEVICE__. Change-Id: Ib74c9b2d8753e6e37e1a23fcfaa2f3657790d4c0 Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: http://review.coreboot.org/3555 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@google.com>
2013-07-30Makefile: Fix adding intel/commonKyösti Mälkki
Directory intel/common must be conditionally added in the list of source directories, as the parent directory southbridge/intel is unconditionally added even for boards without such device. Change-Id: I7088bc6db9f56909ffa996aa7eff76cd72e177eb Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: http://review.coreboot.org/3827 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@google.com>
2013-07-16AMD Fam15tn: Split DSDT into common sectionsSteve Goodrich
Split the Parmer, Family 15tn, and Hudson DSDT into groups. This splits the DSDT table into includable ASL files which carry details specific to the Family 15tn APU, the Parmer platform, and the Hudson FCH. The dsdt.asl file in the mainboard directory contains only #include references to the appropriate files. Initially, this split was done by moving each piece of functionality into its own file (e.g. IRQ routing and mapping, processor tree, sleep states and sleep methods, etc.) and those pieces were #included in dsdt.asl to ensure an exact match (via acpidump/acpixtract/iasl -d) with the extant version of the table. Once the new tables were found to exactly match the existing tables, the pieces were rearranged into reasonable groups (e.g. fch.asl, northbridge.asl, pci_int.asl, etc.). Some include files have no content but are left as a template for other platforms and as placeholders for completing the ACPI implementation for Parmer (e.g. thermal.asl, superio.asl, ide.asl, sata.asl, etc.). Change-Id: I098b0c5ca27629da9bc1cff1e6ba9fa6703e2710 Signed-off-by: Steve Goodrich <steve.goodrich@se-eng.com> Reviewed-on: http://review.coreboot.org/3629 Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Tested-by: build bot (Jenkins) Reviewed-by: Marc Jones <marc.jones@se-eng.com>
2013-07-12src/southbridge/intel/{lynxpoint,bd82x6x}/spi.c: correct spelling of attemptedPaul Menzel
Change-Id: Ic6f6af6298fed2f41f140a7aa62dccf98bf60927 Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-on: http://review.coreboot.org/3572 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-07-10Vortex86EX southbridge routes more built-in PCI device IRQs.Andrew Wu
Routes IRQs for USB device, SPI1, MOTOR, HD audio, CAN bus. Change-Id: I995a5c6d3ed6a7dca4f0d21545c928132ccbbc21 Signed-off-by: Andrew Wu <arw@dmp.com.tw> Reviewed-on: http://review.coreboot.org/3725 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-07-10Drop some duplicates of PCI-e config functionsKyösti Mälkki
These are not specific to Intel. Further work needs to be done to combine these with MMCONF_SUPPORT in arch/io.h. Change-Id: Id429db2df8d47433117c21133d80fc985b3e11e4 Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: http://review.coreboot.org/3502 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-07-10southbridge/intel/i82801gx: Make compilation possible with CONFIG_SMM_TSEGDenis 'GNUtoo' Carikli
Without that fix, and with CONFIG_SMM_TSEG, we have: src/southbridge/intel/i82801gx/smihandler.c: In function 'southbridge_smi_sleep': src/southbridge/intel/i82801gx/smihandler.c:340:3: error: implicit declaration of function 'smi_release_lock' [-Werror=implicit-function-declaration] cc1: all warnings being treated as errors make: *** [build/southbridge/intel/i82801gx/smihandler.smm.o] Error 1 The fix is modelled after src/cpu/x86/smm/smihandler.c which ifdefs smi_release_lock(). Change-Id: Icdc6d039b34a1d95d0e607419bba2484d21abc5e Signed-off-by: Denis 'GNUtoo' Carikli <GNUtoo@no-log.org> Reviewed-on: http://review.coreboot.org/3281 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-07-10i82801gx: smihandle: sync with southbridge/intel/bd82x6x/smihandler.cDenis 'GNUtoo' Carikli
Change-Id: Ic725b169061bd426aa8206dc1d6d31e67cc639f2 Signed-off-by: Denis 'GNUtoo' Carikli <GNUtoo@no-log.org> Reviewed-on: http://review.coreboot.org/3304 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-07-10southbridge: i82801gx: smihandler.c: Correct outl->outw mistake.Denis 'GNUtoo' Carikli
This mistake was spoted by comparison with the src/southbridge/intel/bd82x6x/smihandler.c file. Change-Id: I1516f0131d524bd7d001e6780e9a45402d1814d1 Signed-off-by: Denis 'GNUtoo' Carikli <GNUtoo@no-log.org> Reviewed-on: http://review.coreboot.org/3303 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-07-10sandybridge: Add option to lock SPI regions on resumeNico Huber
Add an option to mark all SPI regions write protected on each S3 resume. We were used to lock the SPI interface in the payload which isn't run on the resume path. So we have to do it here. For the write protection to be effective, all write opcodes in the opmenu have to be marked correctly (as write operations) and the whole SPI interface has to be locked. Both is already done. Change-Id: I5c268ae8850642f5e82f18c28c71cf1ae248dbff Signed-off-by: Nico Huber <nico.huber@secunet.com> Reviewed-on: http://review.coreboot.org/3594 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Ronald G. Minnich <rminnich@gmail.com> Reviewed-by: Patrick Georgi <patrick@georgi-clan.de> Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-07-03Add support for DMP Vortex86EX PCI southbridge.Andrew Wu
Change-Id: Iad11cb1b22e9d1e2953b12221541b1478cad9665 Signed-off-by: Andrew Wu <arw@dmp.com.tw> Reviewed-on: http://review.coreboot.org/3547 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-07-01usbdebug: Support i82801dx/ex southbridgeKyösti Mälkki
Tested on i82801dx system with board aopen/dxplplusu. Change-Id: I522455ac79c87b9b6fc9cd8c4dc0da3563dfbfad Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: http://review.coreboot.org/3381 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@google.com> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2013-07-01usbdebug: Unify Intel southbridge buildsKyösti Mälkki
EHCI controller enable is identical on the affected chipsets. Change-Id: I91830b6f5144a70b158ec1ee40e9cba5fab3fbc9 Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: http://review.coreboot.org/3424 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@google.com> Reviewed-by: Marc Jones <marc.jones@se-eng.com>
2013-07-01usbdebug: Drop duplicates of EHCI BAR relocation codeKyösti Mälkki
All the additional work that needs to be done in EHCI BAR relocation is independent of the hardware platform and was functionally identical in all the copies removed. When USBDEBUG is not selected, PCI EHCI controllers use standard pci_dev_read_resources() call. With USBDEBUG selected, PCI EHCI controller's device_operations .read_resources is replaced with pci_ehci_read_resources() call, which in turn will replace the device_operations .set_resources call. The replacement for .set_resources reconfigures usbdebug driver side, and calls the original .set_resources to configure hardware side. Change-Id: I8e136a5da4efedf60b6dd7068c0488153efaaf8e Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: http://review.coreboot.org/3412 Reviewed-by: Aaron Durbin <adurbin@google.com> Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2013-06-29AMD S3 resume: Add framwork to write bigger dataSiyuan Wang
This patch is based on 'AMD S3: Program the flash in a bigger data packet'[1] Some AMD south bridge can write bigger data when saving S3 info. In this patch, I use config 'AMD_SB_SPI_TX_LEN' to contral data size. AMD_SB_SPI_TX_LEN is defined in 'src/southbridge/amd/Kconfig' and then can be overridden in the Kconfig for specific southbridges that support larger size. I have tested on AMD Parmer and Thatcher. We will release a new board whose south bridge can transfer more than 4 bytes each time. [1] http://review.coreboot.org/#/c/2306/ Change-Id: Id984955d46eae487e39d45979f1a90054aa9f54b Signed-off-by: Siyuan Wang <SiYuan.Wang@amd.com> Signed-off-by: Siyuan Wang <wangsiyuanbuaa@gmail.com> Reviewed-on: http://review.coreboot.org/3413 Tested-by: build bot (Jenkins) Reviewed-by: Bruce Griffith <Bruce.Griffith@se-eng.com> Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-06-28amd/cimx/sb700/late.c: Add type cast to (UINT8)Bruce Griffith
This change inserts a type cast to eliminate a compiler warning. Change-Id: If223f61f1565caeadb1b7e0762975b1b2412eda5 Signed-off-by: Bruce Griffith <Bruce.Griffith@se-eng.com> Reviewed-on: http://review.coreboot.org/3541 Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-06-25bd82x6x: Fix early USB BAR programming (finally?)Nico Huber
The xHCI controller's MMIO space has a length of 64KiB not 4KiB. Therefore, setting the xHCI BAR to 0xe8001000 worked the same like setting it to 0xe8000000, as bit12 is reserved and ignored. This again interfered with the MMIO space of the first EHCI controller and broke S3 resume on Ivy Bridge. AFAIK, the MRC ignores the setting of the xHCI BAR, anyway. So just drop these lines. Change-Id: I8af9c2ba34133f15636a9056fc8880b3b6ab95e0 Signed-off-by: Nico Huber <nico.huber@secunet.com> Reviewed-on: http://review.coreboot.org/3521 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Marc Jones <marc.jones@se-eng.com>
2013-06-25sandybridge: Make inclusion of me.bin optionalNico Huber
Current build configuration always wants to include an Intel Management Engine firmware (me.bin) on Sandy Bridge systems. However, we can have a working coreboot without it, as long as the factory delivered ME firmware is kept untouched in the flash ROM. So let the user decide if a ME firmware will be included in the build. Change-Id: I9a1cc29d4940ba22355eb9e653606e436f07e04c Signed-off-by: Nico Huber <nico.huber@secunet.com> Reviewed-on: http://review.coreboot.org/3522 Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Tested-by: build bot (Jenkins) Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
2013-06-24sandybridge: Make build possible without descriptor.binNico Huber
On newer Intel systems, the flash ROM is shared between the host processor (BIOS), it's Management Engine (ME) and an integrated ethernet controller (GbE). The layout of the flash ROM (and other information) is kept in the so called Intel Firmware Descriptor (IFD). If we only want to build coreboot to update the BIOS section, all we need is the flash layout. This patch adds the option to specify the flash layout in the mainboard's Kconfig, and thus, to build without the real IFD. However, with such a build, one has to make sure that the IFD section on the flash ROM won't be written over (nor any other section that hasn't been included by coreboot). A patch to write selected sections of a flash ROM with IFD has been sent to the flashrom mailing list [1]. [1] http://www.flashrom.org/pipermail/flashrom/2013-June/011083.html Change-Id: Ia23e439a00a197fb54852263f8e206f16c3e8851 Signed-off-by: Nico Huber <nico.huber@secunet.com> Reviewed-on: http://review.coreboot.org/3524 Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-06-23lynxpoint: Fix early EHCI BAR programmingKyösti Mälkki
LynxPoint LP has only EHCI controller #1. Change EHCI #2 to different BAR from EHCI #1. Even if the ECHI controllers are not to be addressed, it is bad idea to set two different devices to claim the same PCI memory cycles. Change-Id: I95c59fb9d5f09afd152872e9bc0418dc67e4aeb2 Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: http://review.coreboot.org/3472 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Aaron Durbin <adurbin@google.com>
2013-06-21bd82x6x: Fix early EHCI BAR programmingKyösti Mälkki
Change EHCI #2 to different BAR from EHCI #1. Even if the ECHI controllers are not to be addressed, it is bad idea to set two different devices to claim the same PCI memory cycles. Change-Id: Ib6f7cfac5acf3f8170508547d1584af90273e8c1 Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: http://review.coreboot.org/3471 Tested-by: build bot (Jenkins) Reviewed-by: Nico Huber <nico.huber@secunet.com>
2013-06-19intel/i82801gx: Store initial timestampNico Huber
Upgrade the ICH7 bootblock to store an initial timestamp like we do it since Sandy Brigde. I've checked the datasheets for the used scratchpad registers and grepped for their usage. I'm pretty sure that they aren't used on any ICH7 based board (for anything before the usual S3-resume indication). Change-Id: I28a9b90d3e6f6401a8114ecd240554a5dddc0eb5 Signed-off-by: Nico Huber <nico.h@gmx.de> Reviewed-on: http://review.coreboot.org/3498 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-06-17AMD southbridges: Move HAVE_HARD_RESETKyösti Mälkki
All 3 boards with AGESA_HUDSON had HAVE_HARD_RESET with the reset.c file already placed under southbridge/. All 15 boards with CIMX_SBx00 had HAVE_HARD_RESET with functionally identical reset.c file under mainboard/. Move those files under respective southbridge/. Change-Id: Icfda51527ee62e578067a7fc9dcf60bc9860b269 Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: http://review.coreboot.org/3486 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Marc Jones <marc.jones@se-eng.com>
2013-06-17AMD Hudson: Add config option to enable XHCIDave Frodin
To have USB 3.0 support the XHCI controller needs to be enabled and the xhci.bin firmware needs to be added to CBFS. Change-Id: I0b641b30b67163b7dc73ee7ae67efe678e11c000 Signed-off-by: Dave Frodin <dave.frodin@se-eng.com> Reviewed-on: http://review.coreboot.org/3464 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-06-17Make intel blob locations configurablePatrick Georgi
They were hard-coded to be copied from 3rdparty/ which isn't always the right choice. Since the defaults stay the same, this should be compatible. Change-Id: If2173bef86ad1fcf2335e13472ea8ca41eb41f3d Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com> Reviewed-on: http://review.coreboot.org/3453 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Marc Jones <marc.jones@se-eng.com>
2013-06-14AMD sb800 agesa/hudson: Use PCI definesKyösti Mälkki
The original lines had contradicting comment and code. This change follows the code and sets MASTER bit too. Change-Id: Id2886bfc107612530f0e9747e5d49a9740fb8532 Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: http://review.coreboot.org/3466 Tested-by: build bot (Jenkins) Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
2013-06-14lynxpoint: Fix PCI IDs for EHCIKyösti Mälkki
IDs were leftovers from bd82x6x. Change-Id: I4ab6062929d346d7f000ce8c0b8c97490bb2b154 Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: http://review.coreboot.org/3463 Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Aaron Durbin <adurbin@google.com> Tested-by: build bot (Jenkins)
2013-06-13AMD Hudson: Add support for the SD controllerDave Frodin
This patch provides the correct SD controller timings for the Family16 device. It also will remove the SD controller from PCI space when device 0:14.7 is set to off in devicetree. This was tested on a AMD Parmer board and a AMD G-series SOC reference board. The settings were found in the AMD Hudson2 RRG and family16 BKGD. Change-Id: I6d7e7997ddc39802ab75dc8a211ed29f028c0471 Signed-off-by: Dave Frodin <dave.frodin@se-eng.com> Reviewed-on: http://review.coreboot.org/3348 Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-06-13AMD: Kconfig cleanupKyösti Mälkki
Change-Id: I21182eae1d389790c330f27e6a830d91c3ee4eb6 Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: http://review.coreboot.org/3433 Tested-by: build bot (Jenkins) Reviewed-by: Marc Jones <marc.jones@se-eng.com>
2013-06-13Revert "Add support for Intel Ibex Peak (Mobile 5) southbridge"Stefan Reinauer
This reverts commit 0210119b4b95e84f954cfd6dc11aafbc187421af Change-Id: I5be3f2a54394c592650a0dcd671e4a72ae796cb2 Reviewed-on: http://review.coreboot.org/3443 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-06-12Add support for Intel Ibex Peak (Mobile 5) southbridgeStefan Reinauer
Change-Id: If56f2cacc5f1b2ef9c7b6aea508d458a43dd1309 Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com> Signed-off-by: Stefan Reinauer <reinauer@google.com> Reviewed-on: http://review.coreboot.org/3397 Tested-by: build bot (Jenkins) Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
2013-06-12usbdebug: Drop printk within console_init()Kyösti Mälkki
In case with EARLY_CONSOLE, this printk is called before any other console is configured to transmit data. This outputs garbage on CONSOLE_SERIAL as baudrate is not yet programmed. For case without EARLY_CONSOLE, the order in which different console drivers initialize is obscure. Might sometimes work properly. Change-Id: I3792161e0a6dc17e17262048cc9136044dd69dc5 Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: http://review.coreboot.org/3384 Tested-by: build bot (Jenkins) Reviewed-by: Marc Jones <marc.jones@se-eng.com>
2013-06-12Fix i82801a/b/c/d IOAPICKyösti Mälkki
Setting IRQ delivery to FSB got lost in the rebase process for commit e6143531. I captured following error on dmesg and this patch fixes it for i82801dx. ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1 ..MP-BIOS bug: 8254 timer not connected to IO-APIC ...trying to set up timer (IRQ0) through the 8259A ... ..... (found apic 0 pin 2) ... ....... failed. ...trying to set up timer as Virtual Wire IRQ... ..... works. Change-Id: I0768976cc6b0deab213ad9bd4771e0f278de634c Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: http://review.coreboot.org/3371 Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Tested-by: build bot (Jenkins) Reviewed-by: Marc Jones <marc.jones@se-eng.com>
2013-06-12intel/*/smi.c: Output correct GPIO in ALT_GP_SMI_STS register dumpKonstantin Aladyshev
Mapping is as follows: bit 15 corresponds to GPIO15 ... bit 0 corresponds to GPIO0. Change-Id: I661ce56d9373887270ba3c0518892fbbe6d9de7c Signed-off-by: Konstantin Aladyshev <aladyshev@nicevt.ru> Reviewed-on: http://review.coreboot.org/3436 Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-06-11intel/bd82x6x/Makefile.inc: Revert duplicate addition of `usb_debug.c`Paul Menzel
Currently in Intel BD82x6x southbridge’s `Makefile.inc` the file `usb_debug.c` is added twice to the build. This was introduced in commit 4063ede3fb571110c3e65c321049cc2687cc54fa Author: Ronald G. Minnich <rminnich@google.com> Date: Mon Feb 4 20:31:51 2013 -0800 bd82x6x: Fix compiling with USB debug port support Reviewed-on: http://review.coreboot.org/2784 but was unneeded because it had been already added in the following commit. commit 4141993536039e0d45caeacb745a89d388f0724b Author: Sven Schnelle <svens@stackframe.org> Date: Sat Jul 28 08:52:44 2012 +0200 bd82x6x: Fix CONFIG_USBDEBUG Reviewed-on: http://review.coreboot.org/1376 Therefore basically revert that hunk. There is no policy on how to order these additions, so leave it to a possible separate commit, unifying this. Kyösti Mälkki suspects that these additions were meant for the Intel Lynx Point [1]. [1] http://review.coreboot.org/#/c/3424/ Change-Id: Iaa8de6fcc0d6f3a0a92a28fcb603d7777aa8b24c Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-on: http://review.coreboot.org/3425 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2013-06-11Fix cycle error in intel southbridges to display GPI statusKonstantin Aladyshev
Fix obvious mistake in cycle that displays GPI status I hope i found all duplicates of it. Change-Id: Ic21ff3ecab85953463e5c23daf808dd5edc82ff8 Signed-off-by: Konstantin Aladyshev <aladyshev@nicevt.ru> Reviewed-on: http://review.coreboot.org/3435 Tested-by: build bot (Jenkins) Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>