| Age | Commit message (Collapse) | Author |
|---|
|
The current early PM setup that attempts to configure dynamic clock
gating relies on PCIe functions to be enabled that may not be.
Instead of reading port 0 or 4 directly to determine the link width
use the register that refelects the soft strapping options as this
will always be available.
Also add a clear register assignment and break for port 0 in the
switch statement instead of falling through to port 4 as that could
end up setting the slot power limit based on port 4 values instead
of based on port 0.
register 0xE1=0x3f and all other root ports should have 0xE1=0x03.
When port 0 and 4 are disabled they will have 0xE1=0x3C before
being disabled by the pch enable handler.
LUMPY default:
00:1c.0 PCI bridge: Intel Corporation Device 1c10 (rev b5)
00:1c.3 PCI bridge: Intel Corporation Device 1c16 (rev b5)
pci_read8 0 0x1c 0 0xe1
0x3f
pci_read8 0 0x1c 3 0xe1
0x03
LUMPY with PCIe port coalesce enabled:
00:1c.0 PCI bridge: Intel Corporation Device 1c10 (rev b5)
00:1c.1 PCI bridge: Intel Corporation Device 1c16 (rev b5)
pci_read8 0 0x1c 0 0xe1
0x3f
pci_read8 0 0x1c 1 0xe1
0x03
Change-Id: I33a37b0ec0c8e570cf5d9dda2c06e0225fee135c
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/980
Tested-by: build bot (Jenkins)
|
|
Background: The PCI spec (3.0-3.2.2.3.4) requires that PCI devices
implement function 0. The Linux Kernel therefore will not enumerate
a PCI device if it does not present a valid config space at function 0.
If a board does not have anything connected to root port 0 and it is
desired to disable the unused ports in order to save power then this
will cause the other downstream PCIe devices to go missing as they
will not be enumerated.
Intel chipsets provide a way to map root port numbers to different PCI
function numbers, thereby avoiding this issue and allowing root port 0
to be turned off.
This change adds a new chip config option 'pcie_port_coalesce' that
will collapse the enabled root ports into a linear map starting at
zero. This option defaults to disabled as it can have a confusing
effect on the system as the declared static devicetree may not match
what is seen at runtime. This option is also forced on if the static
devicetree disables port 0.
When each root port is processed in the early enable stage it looks
for a lower numbered root port that has been disabled and then swaps
the two assigned function numbers.
However the mapping register is write-once so it has to keep track of
the proposed mapping changes until all ports have been processed
before writing out the final map value. At this point it also updates
the function numbers in the static device tree so they are consistent
with the new layout.
There are a few other closely related fixes in this change:
1) There is a power savings opportunity if an entire bank of ports
(0-3 or 4-7) are disabled. This was checking the chipset revision to
look for CougarPoint B1+ stepping and that was not passing on
PantherPoint where this should always be applied. To fix this I added
a function to determine the chipset type based on comparing the upper
byte of the device ID.
2) Apply the same chipset type check fix to the IOBP programming.
3) There is another power savings opportunity to enable dynamic clock
gating on shared PCIe resources which only applies to ports 0 and 4.
However if 0 or 4 is disabled then the later check to enable this
would fail as that device is already hidden.
LUMPY current:
00:1c.0 PCI bridge: Intel Corporation Device 1c10 (rev b5)
00:1c.3 PCI bridge: Intel Corporation Device 1c16 (rev b5)
01:00.0 Network controller: Atheros Communications Inc. Device 0030 (rev 01)
02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B
LUMPY with PCIe port coalesce enabled:
00:1c.0 PCI bridge: Intel Corporation Device 1c10 (rev b5)
00:1c.1 PCI bridge: Intel Corporation Device 1c16 (rev b5)
01:00.0 Network controller: Atheros Communications Inc. Device 0030 (rev 01)
02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B
Change-Id: I828aa407fdc9c156c1c42eda8e2d893c0aa66eef
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/979
Tested-by: build bot (Jenkins)
|
|
The chipset enforces static-defined interrupt swizzling on PCIe root
ports so if a port is remapped to a different function it needs to
still report the proper interrupt map to the OS instead of assuming
that function number is equivalent to root port number.
This change also includes an update to the PCH function disable
register which was incorrect for CPT/PPT and would cause unpredictable
behavior if used.
The kernel command line was changed to add 'nomsi' in order to force
PCIe devices to use IO-APIC assigned interrupts and not MSI to ensure
that the mapping is correct.
LUMPY current:
00:1c.0 PCI bridge: Intel Corporation Device 1c10 (rev b5)
00:1c.3 PCI bridge: Intel Corporation Device 1c16 (rev b5)
16: 41518 0 0 0 IO-APIC-fasteoi i915, ahci, ath9k
19: 720 0 0 0 IO-APIC-fasteoi ehci_hcd:usb2, eth0
LUMPY with PCIe port coalesce enabled:
00:1c.0 PCI bridge: Intel Corporation Device 1c10 (rev b5)
00:1c.1 PCI bridge: Intel Corporation Device 1c16 (rev b5)
16: 38988 0 0 0 IO-APIC-fasteoi i915, ahci, ath9k
19: 347 0 0 0 IO-APIC-fasteoi ehci_hcd:usb2, eth0
Change-Id: Ia5f6bb8888b5c38a5dbc88bb25ecdf1fca41ee3e
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/978
Tested-by: build bot (Jenkins)
|
|
The sata controller comes up in legacy/normal mode and
is currently put into AHCI mode in romstage.
If that is removed and the controller is left alone until the
ramstage driver (like we do on Stumpy/Lumpy) then the resource
allocator will have configured the device for IDE mode with an
IO address in BAR5. Then when the ramstage driver puts the
controller into AHCI mode it will not have the correct resources
to do the rest of the AHCI setup.
So the controller mode needs to be changed in the enable stage
rather than in the init phase. This same register contains
the port map and it is a R/WO (write once) field so the configured
port map must be written at the same time. For non-AHCI mode
the devicetree map was ignored before but it is used now.
Since the port map register is now written at enable step it
does not need to be written again during init.
With this change the sata port map can be reduced to just port 0
and then U-boot does not have to probe all available ports.
Change-Id: I977952cd88797ab4cea79202e832ecbb5c37e0bd
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/977
Tested-by: build bot (Jenkins)
|
|
The OS does not re-execute the APMC 'enable ACPI' SMI
on resume so this has the potential to leave things
in an unknown state.
Change-Id: Iaf0fcb99f699e9e0ecacaab3f529026782a95151
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/971
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
This adds the PCI device id of the LPC controller identifying the
QPRJ/QS stepping of the Panther Point southbridge.
Change-Id: Idcaa7dbd30224e3690ea469c6cb74f75de287631
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: http://review.coreboot.org/968
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Many PCI devices share the very same driver despite having different
PCI device IDs, which causes a lot of copy and paste of driver
definitions.
This change introduces a way to specify the array of acceptable
device IDs in a single driver entry. As an example the Intel
{Sandy|Ivy} Bridge SATA driver is being modified to use a single
driver structure for all different SATA controller flavors, a few
more Ivy Bridge IDs are being added as well.
BUG=none
TEST=manual
. modified coreboot brought up an Ivy Bridge platform all the
way to Linux login screen.
Change-Id: I761c5611b93ef946053783f7a755e6c456dd6991
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: http://review.coreboot.org/982
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
post_code() was added in our internal tree by duplicating code. It's not of
much use at this point, since the code is quite well tested, so avoid bloating
the bootblock (since compiled with ROMCC).
Also add some missing include files that didn't seem to be needed with an
older version of coreboot.
Change-Id: Id62b838728a247e8bcadb4f1db17269be0d4f3f4
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/936
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
rename from mainboard_apm_cnt to mainboard_smi_apmc to match the function
naming scheme of the other handlers. Add prototype for mainboard_smi_sleep
(mainboard specific S3 sleep handlers in SMM) that is required by Sandybridge.
Change-Id: Ib479397e460e33772d90d9d41dba267e4e7e3008
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/933
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Add early_smbus.c for romstage-y list and remove respective
include on mainboard romstage.c files.
Tested on AOpen board.
Change-Id: I1c7e6cb32e3a9d7cc9b6037dc27e59149d492001
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/909
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Made using coccinelle:
@@
expression E;
@@
-(E + 7) & -8
+ALIGN(E, 8)
@@
expression E;
@@
-(E + 15) & -16
+ALIGN(E, 16)
Change-Id: I071d2c98cd95580d7de21d256c31b6368a3dc70b
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/910
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
S3.rom is useless for all the other boards which don't use flash to
save sleep/wakeup settings. AGESA-based boards other than persimmon
haven't been validated the S3 resume. They don't need S3.rom yet.
Change-Id: I12693e9556ca6f8e0d80b2ab2dca5c85bdb97685
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: zbao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/902
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
echo -n isn't portable. echo -e isn't portable. that bash loop isn't portable.
So let's try something else.
Change-Id: Ie73aa1c09d90c11a5c4952a332d4c2058390b5db
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/889
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Zheng Bao <zheng.bao@amd.com>
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
1. Add some CIMX call for S3.
2. Detect sleep type.
Change-Id: I62888e8d8a03987ca88f5c935fa660f6b49a4fe9
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: zbao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/621
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Some places still hardcoded the address instead of using IO_APIC_ADDR.
Change-Id: I3941c1ff62972ce56a5bc466eab7134f901773d3
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/677
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Change-Id: Iac3cd25b36493bb203e849674320e113cc5fce32
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/853
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
It is for S3, storing the recovring data in the nonvolatile storage,
i.e., flash.
Change-Id: Ie9e4f42a80c93d92d2e442f0e833ce06d88294f9
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: zbao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/620
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
|
|
So far it just setups things right for Bifferboard. We may change it
in the future to fit other hardware.
Change-Id: I1c4ccff4e47b9cb9e31a738f038fc4f4ebe59087
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Reviewed-on: http://review.coreboot.org/808
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Changing CMOS value for power-on-after-power-fail was only honored
after reboot, which is counter intuitive (set from "enable" to "disable",
power-off, replug device -> device turns on; and similar cases).
Change-Id: If1d88c1c34c3333b636ed3ec1e1fb9bea394e615
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/444
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
We used a hard coded value for some reason. Don't do that, but use CMOS
instead.
Change-Id: Ib83aa07a3e55bed075150354a060317ebc9d5ba7
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/443
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Use separate Kconfig option to select a driver directory for
build and the specific type of southbridge to support.
Change-Id: I9482d4ea0f0234b9b7ff38144e45022ab95cf3f3
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/685
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Also mark the corresponding lint test stable.
Change-Id: Ib7c9ed88c5254bf56e68c01cdbd5ab91cd7bfc2f
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/772
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Southbridge SP5100 support was compiled with SB700 code, but static
device info structure would use sp5100/chip.h. To solve this drop
support for separate chip sp5100 and adjust the relevant Kconfig
options.
Removes chip directory:
src/southbridge/amd/sp5100/
Rename Kconfig option
from: SOUTHBRIDGE_AMD_SP5100
to: SOUTHBRIDGE_AMD_SUBTYPE_SP5100
Change-Id: I873c6ad3624ee69165da6ab7287dfb7e006ee8e8
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/679
Tested-by: build bot (Jenkins)
Reviewed-by: Zheng Bao <zheng.bao@amd.com>
Reviewed-by: Marc Jones <marcj303@gmail.com>
|
|
No in-tree board using that chipset has it not selected, so move
selection from boards to southbridge.
Change-Id: I16b27e40ca1a201b2f968f8ce303eaafe43804c0
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/660
Tested-by: build bot (Jenkins)
|
|
If PCI config cycles use MMIO instead of I/O in the SB600 bootblock
code the cycles will go nowhere since the MMIO feature hasn't been
configured yet. This change forces the cycles to use I/O and
configures the southbridge decode range to what is defined by the
mainboards Kconfig.
Change-Id: I85297237f32f37b3fc1ff5b488cca0a43bcf20fd
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: http://review.coreboot.org/632
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
If PCI config cycles use MMIO instead of I/O in the SB700
bootblock code the cycles will go nowhere since the MMIO feature
hasn't been configured yet. This change forces the cycles to use
I/O and configures the southbridge decode range to what is specified
by the mainboards Kconfig.
Change-Id: I15a89a27645edf594d14ef20f129f75a315e9672
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: http://review.coreboot.org/631
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
If PCI config cycles use MMIO instead of I/O in the bootblock
code the cycles will go nowhere since the MMIO feature hasn't been
configured yet. This change forces the cycles to use I/O.
Change-Id: I93dec45f7cd6764cef7736c774a4d4e61bf7d7e0
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: http://review.coreboot.org/630
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Extend the Family10 revisions checked byt the printk message.
Change-Id: Ia94daeefb1aabfb128c577b1e0aa52cf63d5cf44
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: http://review.coreboot.org/633
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
No in-tree board using that chipset has it not selected, so move
selection from boards to southbridge.
Change-Id: Ibfb7b294aa5007ac2f767d85e090572f85148bad
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/659
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
|
|
No in-tree board using that chipset has it not selected, so move
selection from boards to southbridge.
Change-Id: I7a7a1919b7a555156b8da21e8db7dd8f682d68e1
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/661
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
|
|
No in-tree board using that chipset has it not selected, so move
selection from boards to southbridge.
Change-Id: Ifba0b65d81af60774f368d151e935ae1cc768336
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/662
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
|
|
No in-tree board using that chipset has it not selected, so move
selection from boards to southbridge.
Change-Id: I9762ef01fc10c453ef643599c1c5dc8ee78081c3
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/663
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
|
|
No in-tree board using that chipset has it not selected, so move
selection from boards to southbridge.
Change-Id: I83105e92d1cc5d2d12aede564a1ab9c5d912ac56
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/664
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
|
|
No in-tree board using that chipset has it not selected, so move
selection from boards to southbridge.
Change-Id: I521deecf58e5d5de303f1ef2f5ff7e965294de18
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/665
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
|
|
No in-tree board using that chipset has it not selected, so move
selection from boards to southbridge. (cimx/sb800 is a "different"
chipset)
Change-Id: If7cf2a141a1f2df60f687c51fbd760aa405c8480
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/666
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
|
|
The current directory is always part of the search path of cpp when
using #include "..."
Change-Id: I74fe39e0c79835e4b9a927afcbeab21040d8ae52
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/648
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Fix issues reported by new lint test.
Change-Id: I077a829cb4a855cbb3b71b6eb5c66b2068be6def
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/646
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
No in-tree amd8111-using board has it not selected, so move
selection from boards to southbridge.
Change-Id: Iabbaa4cd2fd367ed6decec7ef5cdcbae3b264d52
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/654
Reviewed-by: Marc Jones <marcj303@gmail.com>
Tested-by: build bot (Jenkins)
|
|
No in-tree 82801dx-using board has it not selected, so move
selection from boards to southbridge.
Change-Id: I69671cb6411a6cd9c791059ae9546dff3aff702c
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/655
Reviewed-by: Marc Jones <marcj303@gmail.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Change-Id: If924b7eb176e7d3d82fa394929b653b1ced3a743
Signed-off-by: Kerry Sheh <kerry.she@amd.com>
Signed-off-by: Kerry Sheh <shekairui@gmail.com>
Reviewed-on: http://review.coreboot.org/561
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
|
|
without it, you can't boot from PCI devices like scsi controllers
which require an interrupt set. So preconfigure all pci devices.
Change-Id: I2cd781227701e8363d83bd90e0e36994359fc194
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-on: http://review.coreboot.org/603
Tested-by: build bot (Jenkins)
|
|
AGESA and CIMX build changed from commit 2a830d0b,
sb800 and sb900 CIMX dir already traversed in vendorcode Makefile.
Change-Id: I5101b22e140725337bf5074b9170e582c8e3bf40
Signed-off-by: Kerry Sheh <kerry.she@amd.com>
Signed-off-by: Kerry Sheh <shekairui@gmail.com>
Reviewed-on: http://review.coreboot.org/602
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
BIOS needs to set the bit mask which ports are iplemented on the
board. Without setting this option, seabios fails to boot from
SATA.
Change-Id: I21de3fde3a9cff7c590226f70fa549274f36e2a8
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-on: http://review.coreboot.org/601
Tested-by: build bot (Jenkins)
|
|
i3100 misses the magic SATA init sequence, which makes all
requests fail. Captured from the vendor BIOS, which writes
those bits on all configurations.
Change-Id: I293b7d9cd681181311ecaced6d7df9b2706c711f
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-on: http://review.coreboot.org/600
Tested-by: build bot (Jenkins)
|
|
Change-Id: Id34615f0c229d276d72cdf984cf82ea8cc1a85bb
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/523
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
We used to put the id section at -0x10, with some boards overriding
this to avoid collisions with romstraps.
Hardcode the location at -0x80, at the possible expense of some space
(0x70 bytes).
This also makes the section easier to find in a binary image.
At some point, CONFIG_ID_SECTION_OFFSET can be removed, so this option
is moved to src/Kconfig.deprecated_options.
Change-Id: I6ce2d6e94e57717939bda070bfe0c9df80ca2a89
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/549
Tested-by: build bot (Jenkins)
Reviewed-by: Peter Stuge <peter@stuge.se>
|
|
Change-Id: I6b612dbd3eb6e8cc45f1c7abca85732fb64de98c
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-on: http://review.coreboot.org/531
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Tested-by: build bot (Jenkins)
|
|
Change-Id: I6417a92523eea7307d080669fbc4e16ee28c8a6c
Signed-off-by: Jonathan A. Kollasch <jakllsch@kollasch.net>
Reviewed-on: http://review.coreboot.org/524
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Change-Id: Ie3872c57990f9784aafda14f8c7fc842b3a65260
Signed-off-by: Jonathan A. Kollasch <jakllsch@kollasch.net>
Reviewed-on: http://review.coreboot.org/518
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-by: Marc Jones <marcj303@gmail.com>
|
|
Change-Id: I059d5b155cae051f31cc2495f8a47d53e01af808
Signed-off-by: Jonathan A. Kollasch <jakllsch@kollasch.net>
Reviewed-on: http://review.coreboot.org/519
Tested-by: build bot (Jenkins)
Reviewed-by: Peter Stuge <peter@stuge.se>
|
|
Verb data is required for the HDA audio codec in the sb800 southbridge. Verb
data is not required for mainboards that use G-Series HDMI. It is also a setting
the may be boards specific. This fixes issues with Windows audio on Persimmon.
Change-Id: I067506871e92078d122cf79872363d8937d47e50
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: http://review.coreboot.org/490
Tested-by: build bot (Jenkins)
Reviewed-by: Kerry Sheh <shekairui@gmail.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Untested, changes ramstage build for boards:
supermicro/h8qme_fam10
amd/serengeti_cheetah
amd/serengeti_cheetah_fam10
AMD 8132 was not built for any mainboard due to a typo.
AMD Serengeti Cheetah:
Chip 8151 is referenced in devicetree.cb but was not built.
AMD Serengeti Cheetah Family10:
There are indications the board has 8151, but it is not listed
in the devicetree.cb. The 8151 chip is not added in the build.
Change-Id: I03acdfcc3f3440bd32e81a9a696159903bbbcb50
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/471
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
|
|
With this commit the vgainfo is printed and looks like that on the serial console:
vgainfo:
ulBootUpEngineClock:50000
ulBootUpUMAClock:66700
ulBootUpSidePortClock:0
ulMinSidePortClock:0
ulSystemConfig:0
ulBootUpReqDisplayVector:0
ulOtherDisplayMisc:0
ulDDISlot1Config:0
ulDDISlot2Config:0
ucMemoryType:0
ucUMAChannelNumber:1
ucDockingPinBit:0
ucDockingPinPolarity:0
ulDockingPinCFGInfo:0
ulCPUCapInfo: 2
usNumberOfCyclesInPeriod:0
usMaxNBVoltage:0
usMinNBVoltage:0
usBootUpNBVoltage:0
ulHTLinkFreq:20000
usMinHTLinkWidth:8
usMaxHTLinkWidth:8
usUMASyncStartDelay:100
usUMADataReturnTime:300
usLinkStatusZeroTime:600
ulHighVoltageHTLinkFreq:20000
ulLowVoltageHTLinkFreq:20000
usMaxUpStreamHTLinkWidth:8
usMaxDownStreamHTLinkWidth:8
usMinUpStreamHTLinkWidth:8
usMinDownStreamHTLinkWidth:8
Change-Id: I17c2a13ab52a0f78588f812d4f42f45f9a7b7524
Signed-off-by: Denis 'GNUtoo' Carikli <GNUtoo@no-log.org>
Reviewed-on: http://review.coreboot.org/456
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Change-Id: I9f70da76b5ea451f28a1ad9252c5d879fc4fe315
Signed-off-by: Florian Zumbiehl <florz@florz.de>
Reviewed-on: http://review.coreboot.org/387
Tested-by: build bot (Jenkins)
Reviewed-by: Rudolf Marek <r.marek@assembler.cz>
|
|
Change-Id: I70202d81ddd1b0a00eddca4acabc621e5783e805
Signed-off-by: Florian Zumbiehl <florz@florz.de>
Reviewed-on: http://review.coreboot.org/386
Tested-by: build bot (Jenkins)
Reviewed-by: Rudolf Marek <r.marek@assembler.cz>
|
|
Change-Id: I1b5d23cee9f933aa090c9bd09890c7b335567e17
Signed-off-by: Florian Zumbiehl <florz@florz.de>
Reviewed-on: http://review.coreboot.org/388
Tested-by: build bot (Jenkins)
Reviewed-by: Rudolf Marek <r.marek@assembler.cz>
|
|
Change-Id: I830c9a3daf5ac2e1ecd9a3e725a0b98f06509769
Signed-off-by: Florian Zumbiehl <florz@florz.de>
Reviewed-on: http://review.coreboot.org/385
Tested-by: build bot (Jenkins)
Reviewed-by: Rudolf Marek <r.marek@assembler.cz>
|
|
and remove it from mainboard/intel/mtarvon, as this function
is implemented in the southbridge code.
Change-Id: Id3669aaf99b96b4a7a965f4957e5de7c365acaa6
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-on: http://review.coreboot.org/469
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Change-Id: Ia7e3e77235530e952b2e84fdec8373b90fa59b7a
Signed-off-by: Florian Zumbiehl <florz@florz.de>
Reviewed-on: http://review.coreboot.org/437
Tested-by: build bot (Jenkins)
Reviewed-by: Rudolf Marek <r.marek@assembler.cz>
|
|
make code dependent on CONFIG_SOUTHBRIDGE_VIA_K8T800 also be included
for CONFIG_SOUTHBRIDGE_VIA_K8T800_OLD
Change-Id: I9f4624d08de2790fb513a88ed6207e28e7fbc733
Signed-off-by: Florian Zumbiehl <florz@florz.de>
Reviewed-on: http://review.coreboot.org/374
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Change-Id: I2ad82b8059efb09f0593933cb6f53b51b653d494
Signed-off-by: Florian Zumbiehl <florz@florz.de>
Reviewed-on: http://review.coreboot.org/373
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
http://review.coreboot.org/#change,378 introduced a function in k8x8xx.h
move this function to ctrl.c and add a prototype to the header file instead.
Change-Id: I0919ffb2030c53669b95f58b649d4a160f660923
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/429
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Change-Id: I82d1ec5117a58aaa8cfd2a342b7172a2786f5680
Signed-off-by: Florian Zumbiehl <florz@florz.de>
Reviewed-on: http://review.coreboot.org/379
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Instead of writing to config registers in k8x8xx's dram_enable()
and reading those back in vt8237r_cfg(), factor out generation of
the values and reuse that in both places.
Change-Id: I87a37398efe84b33e6678df74cd40b5abfe4f879
Signed-off-by: Florian Zumbiehl <florz@florz.de>
Reviewed-on: http://review.coreboot.org/378
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Change-Id: Id61678f03e1f7d964f7180a062dd6a689852d4ac
Signed-off-by: Florian Zumbiehl <florz@florz.de>
Reviewed-on: http://review.coreboot.org/401
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
vt8237r_enable() so far wrote the function enable values to the same
offset in the config space of every one of the vt8237's functions,
even though the register is located in the ISA bridge only.
Change-Id: I639586dc238132f5b8d2f320b794948718281b9c
Signed-off-by: Florian Zumbiehl <florz@florz.de>
Reviewed-on: http://review.coreboot.org/368
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
k8t800)" due to dependency issues.
This reverts commit 68c554550f59bd96caace96260ae2e30ed55ceb4
Change-Id: I353bd36b008f489a972c7c656d7ad07416f01387
Reviewed-on: http://review.coreboot.org/398
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Change-Id: I70fe072f8f3447d0be7b7ac64508a954fe47091d
Signed-off-by: Florian Zumbiehl <florz@florz.de>
Reviewed-on: http://review.coreboot.org/372
Tested-by: build bot (Jenkins)
Reviewed-by: Rudolf Marek <r.marek@assembler.cz>
|
|
Change-Id: I10135b37a6cef460be9bfbfd34746140310859a6
Signed-off-by: Florian Zumbiehl <florz@florz.de>
Reviewed-on: http://review.coreboot.org/381
Tested-by: build bot (Jenkins)
Reviewed-by: Rudolf Marek <r.marek@assembler.cz>
|
|
Change-Id: Ib91889a374515d36a2b12b53aeb12b6ea6e22732
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/364
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
- move enable_usbdebug() declaration to usbdebug.h
- reinitialize debug driver in ramstage, as copying the data
structure from romstage doesn't work right now. This way of copying
data from romstage to ramstage is really board/cpu specific, and is
likely to break often. So don't do it.
Change-Id: I394678ded6679c1803e29eb691b926182bdcab68
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-on: http://review.coreboot.org/355
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Change-Id: I3ccb3860207e1b3ccac4313f7b537c434af5166f
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/360
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Rudolf Marek <r.marek@assembler.cz>
|
|
This change removes CONFIG_TINY_BOOTBLOCK, CONFIG_BIG_BOOTBLOCK, and
all their uses, assuming TINY_BOOTBLOCK=y, BIG_BOOTBLOCK=n.
This might break a couple of boards on runtime, but so far, fixes were
quite simple.
There's a flag day: Code that relies on CONFIG_TINY_BOOTBLOCK must be
adapted.
Change-Id: I1e17a4a1b9c9adb8b43ca4db8aed5a6d44d645f5
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/320
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Linux implements it itself, but older Linuxes and other systems
might not. Without this, the host controller might not respond
to drivers.
Change-Id: I4ff0e3683c02e7aa00d188428847c64c4c5d589d
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/345
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Signed-off-by: Oskar Enoksson <enok@lysator.liu.se>
Change-Id: I86c80a27fd13c9a2be4034fdfb63be4ab2fadbfc
Reviewed-on: http://review.coreboot.org/281
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
The code used PCI register 0x92 to enable sata ports,
which is wrong. The ICH7 documentation states:
"This register is only used in systems that do not
support AHCI. In AHCI enabled systems, bits[3:0] must
always be set (ICH7R only) / bits[2,0] must always be set
(Mobile only), and the status of the port is controlled
through AHCI memory space."
Writing 0x0f to ICH7-M doesn't seem to hurt, so lets write
0x0f for both variants. This patch makes sata_ahci work on
my Thinkpad T60 and X60s.
Change-Id: If3b3daec2e5fbaa446de00272ebde01cd8d52475
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-on: http://review.coreboot.org/340
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
If this bit is set, ich7 will enter C4 mode if possible instead of
C3. See ich7 specification (LPC controller, Power management control
registers) for more details.
Change-Id: I352cccdbc51ff6269f153a4542c7ee1df0c01d22
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-on: http://review.coreboot.org/329
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Change-Id: Icbfc47a8d7bfe1600e4212b26e99b2a604de9ef7
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-on: http://review.coreboot.org/326
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Doing it this way will break all subsequent smbus calls, because
the smbus code still uses res->base, which points to the old base
address. Fix this by allocating a proper resource.
Change-Id: I0f3d8fba5f8e2db7fe4ca991ef2c345aff436ea4
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-on: http://review.coreboot.org/325
Reviewed-by: Rudolf Marek <r.marek@assembler.cz>
Tested-by: build bot (Jenkins)
|
|
Add configure option SB_GPP_UNHIDE_PORTS for mainboard
to hide/unhide the unused sb800 gpp ports.
Certain gpp port should be hidden, if no device was detected and
hotplug feature is disabled for such port.
Hidden unused ports makes lspci -vvv get more accurate information under Linux.
Test on avalue/eax-785e mainboard.
Change-Id: I1d7df0f2ab6ad69b1b99b8bf046411ae7cdb09c0
Signed-off-by: Kerry Sheh <kerry.she@amd.com>
Signed-off-by: Kerry Sheh <shekairui@gmail.com>
Reviewed-on: http://review.coreboot.org/207
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
This was mentioned several times already, how about we get it in?
It avoids cbfstool to fail because path/to/"file" doesn't work.
Change-Id: Ia01acbd78f81a5db890fd1573a2f3cbe1450562f
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/305
Tested-by: build bot (Jenkins)
Reviewed-by: Peter Stuge <peter@stuge.se>
|
|
Patch is required to compile this with romcc.
Change-Id: I5c4c0f5b32e5edeb8c48d8455b3493ca79f8b452
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/291
Tested-by: build bot (Jenkins)
Reviewed-by: Peter Stuge <peter@stuge.se>
|
|
Change-Id: I05b08765b38d8d6cc9b7cbdaf87c127b33408c81
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/266
Tested-by: build bot (Jenkins)
Reviewed-by: Uwe Hermann <uwe@hermann-uwe.de>
|
|
Change-Id: I2a3aaf10e453fa6cce8a993356f2a0587178209a
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/276
Tested-by: build bot (Jenkins)
Reviewed-by: Uwe Hermann <uwe@hermann-uwe.de>
|
|
Change-Id: I672135a9b6e3b641ceb655cb00d40ee760c17edc
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/268
Tested-by: build bot (Jenkins)
Reviewed-by: Uwe Hermann <uwe@hermann-uwe.de>
|
|
Change-Id: I0c138ebfdc6d4d5ae7d3512b0dd68df20485690e
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/262
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
|
|
Otherwise with a coreboot log on COM2 (which doesn't work) the boot
process takes eons.
Change-Id: I886f98b715c1f384c8693f2977671ff15897b5a5
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/241
Reviewed-by: Marc Jones <marcj303@gmail.com>
Tested-by: build bot (Jenkins)
|
|
SB800 RAID ROM require to put the misc ROM to specific position,
this patch enable user to put the RAID misc ROM to the right place
in the coreboot image.
Change-Id: I4fc64df8e091fb0cccd063826ab31a4f198942d1
Signed-off-by: Kerry She <kerry.she@amd.com>
Signed-off-by: Kerry She <shekairui@gmail.com>
Reviewed-on: http://review.coreboot.org/249
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
|
|
In order to make sure AHCI/RAID ROM works correctly
For SB800_SATA_AHCI or SB800_SATA_RAID mode, SATA should
enable bus master and the ahci also should be enabled.
Change-Id: I9d9c557816d364d8373fe343860ad5fe45988200
Signed-off-by: Kerry She <kerry.she@amd.com>
Signed-off-by: Kerry She <shekairui@gmail.com>
Reviewed-on: http://review.coreboot.org/248
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
|
|
Add this option to enable/disable SATA IDE Combined Mode feature
Change-Id: I1ab8acd27947a71baf954f44d0741f81f48e5541
Signed-off-by: Kerry Sheh <kerry.she@amd.com>
Signed-off-by: Kerry Sheh <shekairui@gmail.com>
Reviewed-on: http://review.coreboot.org/231
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
|
|
sb800 cimx entry sb_Before_Pci_Init was called in the device 16.2
enable_dev() function. If the devicetree don't have this device,
then sb_Before_Pci_Init will not get called.
Change-Id: I76ebad842e90b0f740abbec031165d7c39a80abf
Signed-off-by: Kerry Sheh <kerry.she@amd.com>
Signed-off-by: Kerry Sheh <shekairui@gmail.com>
Reviewed-on: http://review.coreboot.org/230
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
|
|
If sb800 sata was configured as ahci or raid mode,
give the option to add ROM files.
Change-Id: I87a7814930ce3a7c38cde1e235d151223eea2107
Signed-off-by: Kerry Sheh <kerry.she@amd.com>
Signed-off-by: Kerry Sheh <shekairui@gmail.com>
Reviewed-on: http://review.coreboot.org/225
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
|
|
LXBIOS and LXB-DSDT are not used in other parts of the tree.
Make names consistent across the tree.
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Change-Id: I91caeac09fd2401a36e53bd061d249b236a48e43
Reviewed-on: http://review.coreboot.org/224
Tested-by: build bot (Jenkins)
Reviewed-by: Peter Stuge <peter@stuge.se>
|
|
This change removes printk's that occur before
console init is called. In the best case, these
would cause an extremely slow boot, and in the
worst case would cause a complete post failure.
Change-Id: I50388e71225e95db602aa45835c39126c1c920a3
Signed-off-by: Frank Vibrans <frank.vibrans@amd.com>
Signed-off-by: efdesign98 <efdesign98@gmail.com>
Reviewed-on: http://review.coreboot.org/216
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
|
|
Hide the unused gfx ports and gpp ports if they are not configured as hotplug.
lspci -vvv will get more accurate information under Linux,
tested on avalue/eax-785e.
Change-Id: Iaabfd362a0a01f21d0f49aa2bd2d26f9259013fb
Signed-off-by: Kerry Sheh <kerry.she@amd.com>
Signed-off-by: Kerry Sheh <shekairui@gmail.com>
Reviewed-on: http://review.coreboot.org/206
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Build fix for src/arch/i386/boot/acpi.c if !CONFIG_SMP
Also check for acpi_slp_type 2 in acpi_is_wakeup, since S2
uses the same acpi wakeup vector as S3.
Add _PTS/_WAK methods to turn off/on the CPU/case fans and blink
the power LED while sleeping.
acpi_get_sleep_type() is in a seperate file i82371eb_wakeup.c because
it is used in both romstage and ramstage after patch 3/3, whereas
i82371eb_early_pm.c is used only in romstage.
I used the name acpi_get_sleep_type instead of acpi_is_wakeup_early
because I think acpi_is_wakeup_early is a bit misleading as a name since it
doesn't return a boolean value.
Other chipsets so far only ever set acpi_slp_type to 0 and 3, so the
added check for acpi_slp_type == 2 (resume from S2) should not
change behaviour of other boards:
northbridge/intel/i945/northbridge.c:256:extern u8 acpi_slp_type;
northbridge/intel/i945/northbridge.c:263: acpi_slp_type=0;
northbridge/intel/i945/northbridge.c:267: acpi_slp_type=3;
northbridge/intel/i945/northbridge.c:271: acpi_slp_type=0;
southbridge/intel/i82801gx/i82801gx_lpc.c:171:extern u8 acpi_slp_type;
southbridge/via/vt8237r/vt8237r_lpc.c:149:extern u8 acpi_slp_type;
southbridge/via/vt8237r/vt8237r_lpc.c:238: acpi_slp_type = ((tmp & (7 << 10)) >> 10) == 1 ? 3 : 0 ;
southbridge/via/vt8237r/vt8237r_lpc.c:239: printk(BIOS_DEBUG, "SLP_TYP type was %x %x\n", tmp, acpi_slp_type);
Change-Id: I13feff0b8f49aa988e5467cdbef02981f0a6be8a
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/188
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
This patch enables access to the registers of the hardware monitor
logical device in the superio via isa ports 0x295/0x296.
Previously this was not enabled in the SB8xx LPC device.
This is required for initialisation in init_hwm() in
src/superio/winbond/w83627hf/superio.c and also by OS-level
sensor monitoring such as lm-sensors to access temperature,
fan monitoring and control and voltage registers.
asrock/e350m1 and advansus/a785e-i mainboard changes are included herein.
Change-Id: I2176885549277b335c0c41b48457d09b9b76b703
Signed-off-by: Per Hansen <perh52@runbox.com>
Signed-off-by: Kerry She <shekairui@gmail.com>
Reviewed-on: http://review.coreboot.org/159
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
This change adds the southbridge related code to support
the update of the AMD Family14 cpus to the rec C0 level.
Some of the changes reside in mainboard folders but they
reference changed files in the southbridge folder so they
are included herein.
Change-Id: Ib7786f9f697eaf0bf8abd9140c4dd0c42927ec7e
Signed-off-by: Frank Vibrans <frank.vibrans@amd.com>
Signed-off-by: efdesign98 <efdesign98@gmail.com>
Signed-off-by: Kerry She <kerry.she@amd.com>
Signed-off-by: Kerry She <shekairui@gmail.com>
Reviewed-on: http://review.coreboot.org/135
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
The inline comment of sata_init function seems not placed correctly.
Rearrange it.
Change-Id: I63480da60e51cdc68e64c302ad2d8a6197e288f6
Signed-off-by: Wang Qing Pei <wangqingpei@gmail.com>
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/186
Tested-by: build bot (Jenkins)
|
|
This updates the code for the AMD SR5650 and SB700 southbridges.
Among other things, it changes the romstage.c files by replacing a
.C file include with a pair of .H file includes. The .C file is
now added to the romstage in the SB700 or SR5650 Makefile.inc.
file to the romstage and ramstage elements. This particular change
affects all mainboards that use the SB700, and their changes are
include herein. These mainboards are:
Advansus a785e,
AMD Mahogany, Mahogany-fam10, Tilapia-fam10,
Asrock 939a785gmh,
Asus m4a78-em, m4a785-m,
Gigabyte ma785gm,
Iei Kino-780am2-fam10
Jetway pa78vm5
Supermicro h8scm_fam10
The nuvoton/wpcm450 earlysetup interface is changed because the file
is no longer included in the mainboard romstage.c files.
Change-Id: I502c0b95a7b9e7bb5dd81d03902bbc2143257e33
Signed-off-by: Frank Vibrans <frank.vibrans@amd.com>
Signed-off-by: efdesign98 <efdesign98@gmail.com>
Reviewed-on: http://review.coreboot.org/107
Tested-by: build bot (Jenkins)
Reviewed-by: Kerry She <shekairui@gmail.com>
Reviewed-by: Marc Jones <marcj303@gmail.com>
|
