| Age | Commit message (Collapse) | Author |
|---|
|
Silence unused function warnings, spotted by Clang.
Change-Id: I5127893e9605ca490ff450faa92af5e9eafe8940
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/6054
Tested-by: build bot (Jenkins)
Reviewed-by: David Hendricks <dhendrix@chromium.org>
|
|
This existed for ChromeOS but was no longer used with DYNAMIC_CBMEM.
Change-Id: I558a7ae333e5874670206e20a147dd6598a3a5e7
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/6032
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
|
|
Try to 'standardize' the otherwise peculiar method naming to be somewhat
more in-line with other ACPI implementations. This makes it easier to
compare with vendor DSDT dumps for example.
Change-Id: I5ba54f7361796669ac0cab7ff91e7de43b22e846
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/5888
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
|
|
The IMC functions were being called and timing out when the
CONFIG_SB800_IMC_FWM/CONFIG_HUDSON_IMC_FWM were defined as 0.
Changing to a IS_ENABLED will keep the IMC handshake from
occuring if the IMC firmware isn't running.
Tested on a Persimmon platform which makes three calls to
spi_claim_bus() with each call timing out after 500ms.
Change-Id: I5d4bbcecf003b93704553b495a16bcd15f66763b
Signed-off-by: Dave Frodin <dave.frodin@se-eng.com>
Reviewed-on: http://review.coreboot.org/5974
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
|
|
Allow skipping unknown MBP rather than bailing out.
Change-Id: I9a54858c37d73e320de77aea5a05ab5dcf67cd69
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/5976
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
|
|
The CIMX sb700/sb800/sb900 and agesa/hudson code was treating
the LPC SPI BAR as a normal PCI BAR. This will set the
resources for a fixed size at a fixed address. This was tested
on hp/abm, amd/persimmon, and gizmosphere/gizmo boards.
Change-Id: I1367efe0bbb53b7727258585963f61f4bd02ea1d
Signed-off-by: Dave Frodin <dave.frodin@se-eng.com>
Reviewed-on: http://review.coreboot.org/5947
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Change-Id: Ife3febcc88967386dfae624cd237562a34a68471
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/5956
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Change-Id: I68ae49d20a2524f03c4503f2b3be93f07b9cb6e3
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/5955
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
The PCI_INTR table is an Index/Data pair of I/O ports
0xC00 and 0xC01. This table is responsible for physically
routing IRQs to the PIC and IOAPIC. The settings given
in this table are chipset and mainboard dependent, so the
table values will reside in the mainboard.c file. This
allows for a system to uniquely set its IRQ routing.
The function to write the PCI_INTR table resides in
cimx_util.c because the indices into the table have
the same definitions for all SBx00 FCH chipsets.
The next piece is a function that will read the PCI_INTR
table and program the INT_LINE and INT_PIN registers in
PCI config space appropriately. This function will read
a devices' INT_PIN register, which is always hardcoded to
a value if it uses hardware interrupts. It then uses this
value, along with the device and function numbers to
determine an index into the PCI_INTR table. It will read
the table and program the corresponding value into the PCI
config space register 0x3C, INT_LINE. Finally, it will set
this IRQ number to LEVEL_TRIGGERED on the PIC because it is
a PCI device interrupt and the must be level triggered.
For example, the SB800 USB EHCI device 0:18.2 has an INT_PIN
value hardcoded to 2. This corresponds to PIN B. On the
Persimmon mainboard, I want the USB device to use IRQ 11. I
will program the PCI_INTR table at index 0x31 (this USB device
index) to 11. This function will then read the INT_PIN register,
read the PCI_INTR table, and then program the INT_LINE register
with the value it read. It will then set the IRQ on the PIC to
LEVEL_TRIGGERED by writing a 1 to I/O port 0x4D1 at bit position 4.
Also, the SB700 has slightly different register definitions than
the newer SB800 and SB900 so it needs its own set of #defines for
the pci_intr registers.
Only the Persimmon mainboard is adapted to this change as an
example for other mainboards.
Change-Id: I6de858289a17fa1e1abacf6328ea5099be74b1d6
Signed-off-by: Mike Loptien <mike.loptien@se-eng.com>
Reviewed-on: http://review.coreboot.org/5877
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
|
|
Without this change the IOAPIC memory window would collide
with PCI config space. This was tested on the hp/abm board.
Change-Id: I5dd53463961f75bab80a41dc7beff8d0434b24ae
Signed-off-by: Dave Frodin <dave.frodin@se-eng.com>
Reviewed-on: http://review.coreboot.org/5946
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Spotted by Clang
Change-Id: Ic5b04f6f334bc9b1b014a7ada44e9656f7992063
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/5847
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Spotted by Clang
Change-Id: I14c099625db6f38fd0630b8864cf2a702b81d353
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/5832
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Spotted by Clang.
Change-Id: Ie4bed914ab694f4e96155140b8b54b6eb96d70d7
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/5819
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
|
|
Spotted by Clang
Change-Id: I0f04c380b5ada28fb900710facc293edd65ac177
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/5815
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
|
|
There are a couple of places where CPPFLAGS are
pasted into CFLAGS, eliminate them.
Change-Id: Ic7f568cf87a7d9c5c52e2942032a867161036bd7
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/5765
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Rename INCLUDES to CPPFLAGS since the latter is more
commonly used for preprocessor options.
Change-Id: I522bb01c44856d0eccf221fa43d2d644bdf01d69
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/5764
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Change-Id: Icc12aafc1462c08bca77a1798d4fae86b8250708
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/5748
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Tested-by: build bot (Jenkins)
|
|
Change-Id: I7d0e8d2119a470428cfc01c0738b8988ab75ba2d
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/5624
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
This is a empty struct that has propagated through the superio's & ec's
but really does nothing. Time to get rid of it before it adds yet more
cruft. However, since this touches many superio's at once we do this in
stages by first changing the function type to be a pure procedure.
Change-Id: Ibc732e676a9d4f0269114acabc92b15771d27ef2
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/5617
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Rudolf Marek <r.marek@assembler.cz>
|
|
We should configure i8254/i8259 down in to the southbridge rather than
romstage of every AGESA/CIMx board much like Intel boards do.
Change-Id: Id7c4f0baa0819d52aef9b0ee03c20d0fa16b9352
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/5669
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
CPU - fsp_model_206ax:
- Remove Kconfig options and mark this as using the FSP.
- Use shared FSP cache_as_ram.inc file
Mainboard - intel/cougar_canyon2:
- Update to use the shared FSP header file.
- Modify to call copy_and_run() directly instead of returning to
cache_as_ram.inc.
Northbridge - fsp_sandybridge:
- remove mrccache, fsp_util.[ch]
- add fsp/chipset_fsp_util.[ch] with chipset specific FSP bits.
- Update to use the shared FSP header file.
These changes were validated with FSP:
CHIEFRIVER_FSP_GOLD_001_09-OCTOBER-2013.fd
SHA256: e1bbd614058675636ee45f8dc1a6dbf0e818bcdb32318b7f8d8b6ac0ce730801
MD5: 24965382fbb832f7b184d3f24157abda
Change-Id: Ibc52a78312c2fcbd1e632bc2484e4379a4f057d4
Signed-off-by: Martin Roth <gaumless@gmail.com>
Signed-off-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-on: http://review.coreboot.org/5636
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
|
|
Option AMD_SB_SPI_LEN leaked to non-AMD configs.
Option SPI_FLASH is compulsory with HAVE_ACPI_RESUME.
Change-Id: Ib84c4d9e4fdf670b32b0cae7280fcbb6d3aecaf5
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/5606
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-by: Idwer Vollering <vidwer@gmail.com>
|
|
Rename coreboot_ram stage to ramstage. This is done in order to provide
consistency with other stage names (bootblock, romstage) and to allow any
Makefile rule generalization, required for patches to be submitted later.
Change-Id: Ib66e43b7e17b9c48b2d099670ba7e7d857673386
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: http://review.coreboot.org/5567
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
The ACPI IO ports, and the respective SMI (for HAVE_SMI_HANDLER), were
initialized when the FADT table was written. This works well on a cold
boot, but the ACPI ports are not initialized on S3 resume, as ACPI
tables are not written. This will not work on S3 resume if the default
ports are not what we set them, or if AGESA sets them to some other
value.
To solve this, move the port configuration to southbridge chip init.
Change-Id: Ib4043f0fa5e20f08d320acd12ce84d4d789cd035
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-on: http://review.coreboot.org/5559
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@gmail.com>
|
|
The power button was declared by hudson's ASL as \_SB.PCI0.PWRB, and
always had the wake source declared as GPE3. This is not the correct
wake source for all boards. On some laptops declaring a wake source is
not needed, as the wake mechanism is handled by the EC.
Move the declaration of the power button to mainboard ASL files, and
scope it as \_SB.PWRB . This also makes the naming consistent with the
examples in the ACPI spec. The wake source for the PWRB of HP Pavilion
M6 1035dx is removed, as it is incorrect.
Change-Id: I9c76566025e7f200c0376673f6c6ea299afa4a5d
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-on: http://review.coreboot.org/5546
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@gmail.com>
|
|
The ACPI IO ports were defined twice, and used inconsistently. Only
keep one of the definitions for consistency.
Change-Id: If5744f9375fdaa97ceb9ba03dca8aa825eecf159
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-on: http://review.coreboot.org/5558
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
The SPI controller driver used numerical offsets to access SPI
registers, making it unreadable without the datasheet. Use less magic
and more #defines to improve readability.
Change-Id: I8a1f11645cfce027e5df7a41a98c70249695889e
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-on: http://review.coreboot.org/5557
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Following boards use cimx/sb700:
amd/dinar
supermicro/h8qgi
supermicro/h8scm
tyan/s8226
Only amd/dinar had APIC_ID_OFFSET defined, thus all had 0x0.
There was a nonsense preprocessor directive (MAX_CPUS * MAX_PHYSICAL_CPUS >= 1).
Except for tyan, (MAX_CPUS * MAX_PHYSICAL_CPUS) % 256 == 0.
Together with documented 4-bit restriction for APIC ID field, this APIC ID
programming matches with MP tables and ACPI tables.
I believe this would also fix cases of cimx/sb700 with MAX_CPUS<16, which
we do not have in the tree.
Change-Id: If8d65e95788ba02fc8d331a7af03a4d0d8cf5c69
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/5539
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
All boards had APIC_ID_OFFSET=0 and MAX_PHYSICAL_CPUS=1.
Change-Id: I6f08ea6de92a2af79fb3a99c5edd942b3a321c43
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/5538
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
|
|
Match the definition of NODE_PCI() with get_node_pci(), so romstage
and ramstage agree of the PCI BDFs for nodes.
Note that all board have CONFIG_CDB = 0x18 and the maximum for
nodes = 8, so we always have (CONFIG_CDB + x) < 32.
Change-Id: I676ee53a65ef5b1243df2c5889577dd987c8fc9c
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/5536
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
Refactor hudson_enable_gevent_smi() to allow configuring the interrupt
mode and trigger level. Move the utilities which are useful in SMM to
a separate file that is included in both ramstage and SMM. This is
useful for SMI handlers which need to enable or disable GEVENT SMIs
on-the-fly. A follow-up patch makes use of this infrastructure.
Change-Id: Ifa4c300c00c178b18d7280690cfc4b8367c669b8
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-on: http://review.coreboot.org/170
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@gmail.com>
|
|
Change-Id: I5cd9e1fcf197eae966be710b2ab24f49c6885eb0
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/5529
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
This function isn't used on hudson, and seems to be copy-paste from
older southbridges. It is used in sb700 to enable or disable certain
PCI devices. On hudson, these configuration bits are moved to the PM
space.
Change-Id: I9b967a2d0a5dddc8341204dadeed90460251915c
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-on: http://review.coreboot.org/5513
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@gmail.com>
|
|
This enables the ACPI SMI command port in the FADT table, and sets up
the hardware accordingly. If we have SMI enabled, then we don't set
the SCI_EN bit at boot, causing the OS to send the ACPI_ENABLE
command, as required by the ACPI spec. This gives us a chance to hook
into the mainboard_smi_apmc() handler.
Change-Id: Ib4c63d55b3132578dcae48bfe2092d4ea35821dd
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-on: http://review.coreboot.org/5511
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@gmail.com>
|
|
Change-Id: Ifc368974a7a0dc0756431654fb89668e3846801a
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-on: http://review.coreboot.org/5502
Reviewed-by: Aaron Durbin <adurbin@gmail.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
This sets up the infrastructure to handle SMIs generated by the Hudson
southbridge. An API for interfacing to mainboard handlers is not
defined at this point. A few functions are defined to allow mainboard
code to enable SMIs from GEVENT pins. These are the only functions which
I expect to be needed anytime in the foreseeable future.
SMIs are always acknowledged and cleared, as not clearing an SMI will
cause us to re-enter the SMI, effectively bricking the machine if a
southbridge-generated SMI without a handler occurs.
Change-Id: Ibceb21ac5423eb134d3eb7d24800280b183f7619
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-on: http://review.coreboot.org/5494
Reviewed-by: Aaron Durbin <adurbin@gmail.com>
Tested-by: build bot (Jenkins)
|
|
The MMIO region is set up by AGESA very early on, so we can use it to
access the PM register space in ramstage. 16-bit accessors are also
provided to simplify some setup tasks. 16-bit accesses are not
possible via PIO.
The pm2_iowrite/read accessors are removed, as they are not used.
Change-Id: Ie7967b5086eb004525c39721338c6495aedc8165
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-on: http://review.coreboot.org/5503
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@gmail.com>
|
|
Just like in commit
* 1d87dac hp/pavilion_m6_1035dx: Sanitize #includes
Include AGESA headers specifying the path relative to AGESA_ROOT. The
path is specified relative to AGESA_ROOT as opposed to src/ since this
code may include headers from different AGESA families, depending on
the board.
Change-Id: Ide38cc34e207a8b617d1d319fd9c17a785f55833
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-on: http://review.coreboot.org/5423
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-by: Idwer Vollering <vidwer@gmail.com>
|
|
Not all boards which use the AMD Hudson southbridge have IDE. However,
the southbridge's asl included an 'ide.asl' file which had to be
present in $(mainboard_dir)/acpi.
Address this issue by removing the inclusion of 'ide.asl' from the
southbridge 'fch.asl' and remove 'ide.asl' from Hudson boards, none
of which have IDE.
If future hudosn board will come with IDE, the device can be declared
in the PCIO scope of dsdt.asl, right below the inclusion of 'fch.asl'.
Change-Id: Ie2efb7ebf8f5b527e26d7aaaeafbd3053a9a6b28
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-on: http://review.coreboot.org/5459
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Follow along hudson, cut out "SLP_TYP type was 0" excessively filling
the buffer. We could make this conditional on non-zero?
Change-Id: Iffd4c146b2ac4f57dbc3a011a683c92b6e132e39
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/5495
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Not all boards which use the AMD cimx/sb800 southbridge have IDE.
However, the southbridge's asl included an 'ide.asl' file which had to
be present in $(mainboard_dir)/acpi.
Address this issue by including ide.asl only in boards which have IDE,
and remove it from all other cimx/sb800 boards.
Change-Id: I57fcb4db9f85234b05ae1705ef81a576c478cee6
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/5460
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
GP0e does not fit into the naming scheme of the field units surrounding
this field unit definition. Also the keys for e and 3 are close to each
other supporting the theory that this is indeed a typo.
Change-Id: I43cf288fe1e0240b33971073c1aa8a1db5762e31
Reported-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/5483
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Idwer Vollering <vidwer@gmail.com>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
The SerialIO DwordIo() definition is fixed up before returning
it in the serialio device _CRS method, so the values that are set
in the raw ASL are not actually used.
However modern versions of IASL do not like that the RangeLength is
set to zero and will fail to compile. Set this value to 1 to make
IASL stop complaining, but the real value is still fixed up in _CRS
so this has no real effect on the end result.
Change-Id: Iceb888e54dd4d627c12d078915108a11f45b1a2d
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/5182
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Removing `-Wno-unused-but-set-variable` from `CFLAGS` results in the error
below, when building for example the HP DL145 GL1.
CC southbridge/amd/amd8111/acpi.ramstage.o
src/southbridge/amd/amd8111/acpi.c: In function 'acpi_init':
src/southbridge/amd/amd8111/acpi.c:100:11: error: variable 'dword' set but not used [-Werror=unused-but-set-variable]
Removing the variable `dword` fixes this error.
The read is left in the code, as I do not know if it has an effect or
not.
Change-Id: I9957cef3a996c5974c275423c9de63ccf230974e
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/5315
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
The previous SBxxx generations were setting up LPC bridge based
on the PNP resources. Implement it also for AGESA Hudson.
The AGESA itself opens one big region DFLT_SIO_PME_BASE_ADDRESS
(512 bytes). Make the code smart enough to detect already used
region and if any resource fits into AGESA defined region, do nothing.
Change-Id: I718d034bc4c778697a7bd0506d4550c8f5a43159
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Reviewed-on: http://review.coreboot.org/4497
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
SPI registers didnt change since ICH8. No need to have separate
files for them. Unify.
Change-Id: I4e2ac3221b419c007e135c9ee615fc3b84424cbc
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/5254
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
Without this memory decoding isn't activated which, in turn,
makes SeaBIOS crash.
Change-Id: I3dcc721b500ab7468e1082157eeeed38044462d0
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/5326
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Tested-by: build bot (Jenkins)
|
|
With generic load using 32-bit accesses this is no longer has a
huge impact it previously did. It's also unnecessarily
component-speficific.
Change-Id: I7e8a74ea1ceaa225e1024f9eb43e7280773e2b5a
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/5131
Reviewed-by: Aaron Durbin <adurbin@google.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Properly determine temperature target and set it in early
init rather than hardcoding it in late init.
Change-Id: Ie763f205890674a9dd1d9c5974caaccdd67cea14
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/5264
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Add PCIID from Easynote LM85. Remove unrelated IDs inherited from
BD82x6x.
Change-Id: I03b6e0b2e08a4a6014aa1ef1f8d9a3a567f03ad9
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/5263
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins)
|
|
The Chrome OS environment sends an SMI to finalize the chipset/board
at the end of the "depthcharge" payload, but there is no facility to
send this command if not using the full ChromeOS firmware stack.
This commit adds a callback before booting the payload that will
issue this SMI which will lock down the chipset and route USB devices
to the XHCI controller.
Change-Id: I2db9c44d61ebf8fa28a8a2b260a63d4aa4d75842
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/5181
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
This is responsibility of end-user application. When coreboot does
it, it is only for the purpose of debug console.
Change-Id: Idbbf9528c60b9b819b7bea9dfe84078a3f055bc9
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/5251
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Andrew Wu <arw@dmp.com.tw>
|
|
This sequence was derived from BD82X6X and on ibexpeak it inadvertently
disables interrupts. In older kernels it wasn't a problem but in new kernel
it makes codec probe fail.
Change-Id: I40184ae8c4cfe758869af1a1565b88f0a238150e
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/5074
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Change-Id: I979a40ad3692cd474920f3ee5c6b10c41f75bfdb
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/5256
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Read this variable from PCI configuration capabilities list instead.
Change-Id: I0cfe981833873397c32cd3aa2af307f35f01784b
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/5176
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
Remove the bit of code that was putting the SerialIO devices into
D3Hot state when they are switched from PCI to ACPI mode. Instead,
add the appropriate ACPI Methods to allow the kernel to control the
power state of the device.
The problem seems to be that if the device is put in D3Hot state
before it is switched from PCI to ACPI mode then it does not properly
export its PCI configuration space and cannot be woken back up.
Adding the ACPI Methods for _PS0/_PS3 allows the kernel to transition
the device into D0 state only when it is necessary to communicate with
the device, then put it back into D3Hot state.
Change-Id: I2384ba10bf47750d1c1a35216169ddeee26881df
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/5193
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
It is inappropriate for chipset code to be redefining
types -- especially NULL to a non-pointer type. There's
only one non-straight forward change. A condition
being checked was '!ptr_type == NULL' (0 as int). That
check is actually 'ptr_type != NULL'.
Change-Id: Iab5733e5a573baba6fec94e0c955ba4fad72c836
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/5088
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
This claim is useless when done before EHCI controller reset. Code in
usbdebug_init_() already sets this properly after reset, see use of
DBGP_OWNER.
Change-Id: Ic17493fe4edbbbed6ebcbef35a264fbf188f1fba
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/4709
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
|
|
Change-Id: If723896cc31da75dbb3a63d5dc959764e96fded1
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/5139
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
Change-Id: Ie915ef9dbc45604bd5ca1b610acb12af634fdebe
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/5138
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
Also relocate and split header files, there is some interest
for EHCI debug support without PCI.
Change-Id: Ibe91730eb72dfe0634fb38bdd184043495e2fb08
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/5129
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
|
|
Change-Id: I918ca1d0d0d7bcb7e16d41a12830a0357f15b8ed
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/5130
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Broken with/since commit d1cb0eec.
Original intention was to set the frequency for 'Fast Read' command
in bits 15..14, and enable 'Fast Read' command.
Modified register contains SPI frequency for 'Normal Read' command
in bits 13..12. Default for this is 11b for 16.5 MHz. Existing code
unintentionally clears these bits, increasing SPI frequency to 66MHz
for 'Normal Read' command.
This is above specifications for many common SPI flash components
and also makes flashrom older than 0.9.7-r1750 to operate unreliably
on read/write/erase for these platforms.
Change-Id: I30109e2a0410c0bb0bdc968ea71787396b32e761
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/5089
Tested-by: build bot (Jenkins)
Reviewed-by: Kevin O'Connor <kevin@koconnor.net>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
|
|
imc_reg_init: init fan control related registers.
enable_imc_thermal_zone: AGESA does not enable thermal zone. We enable
it here.
Change-Id: I93c729982d78b6d2c7c20bcb1a3e27a7dd0eba91
Signed-off-by: WANG Siyuan <SiYuan.Wang@amd.com>
Signed-off-by: WANG Siyuan <wangsiyuanbuaa@gmail.com>
Reviewed-on: http://review.coreboot.org/4300
Tested-by: build bot (Jenkins)
Reviewed-by: Rudolf Marek <r.marek@assembler.cz>
|
|
Change-Id: I045f1cff794d3c965c502fff98dd2442af2143bd
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/4839
Tested-by: build bot (Jenkins)
Reviewed-by: Rudolf Marek <r.marek@assembler.cz>
|
|
Change-Id: Iaab076cc014a1ee463866c243636f4f71798ddc4
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/4838
Tested-by: build bot (Jenkins)
Reviewed-by: Rudolf Marek <r.marek@assembler.cz>
|
|
When 2 chips are present to get to the second one you have to use hardware
sequencing. Also use it as the fallback if chip is unknown.
Based on code in flashrom by Stefan Tauner and Carl-Daniel Hailfinger
distributed under compatible license.
Tested on Lenovo X230 which has EN25QH64 (8M) + N25Q032..3E (4M)
Change-Id: I56f3cf0406b5f09fa327ed052c8e8b1df1d8a11f
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/4613
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Change-Id: Iefd6852f2300f703ebed8b52aee627107a024f85
Signed-off-by: Andrew Wu <arw@dmp.com.tw>
Reviewed-on: http://review.coreboot.org/4570
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Change-Id: Ieefc2ad775c16de9aa974b2602d55ee047c9f568
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/4643
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Change-Id: If6646853039d15d6ba0fcf2b9b9b0658004be6e6
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/4787
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Without it ME doesn't always start correctly and no temperature is reported,
no fan management and so on.
Change-Id: Iff71f3afbc35a1453a20d182890ae2d196c556bd
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/4636
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
probably a problem in MRC:
- EHCI output failure after sysagent
- no S3
- no MRC cache
- MRC needs watchdog
- less MTRR could be used by some memory map optimisations
Not tested:
- dock (probably doesn't work)
- msata (probably works)
- wwan (probably works)
- mini displayport (probably works)
Blobs:
MRC
VGA Oprom
Change-Id: I5bdb9372971f48e048848d57b6c924b79782dbde
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/4679
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
|
|
Show POST codes on a PCI device: implement hudson_pci_port80().
Remove the comments that use pci_locate_device():
using the code found in the comment seems to break booting.
This shares much code with sb600/sb700/sb800,
however the deduplication work needs to be discusses somewhere else
than in this review board.
Tested on an Asus F2A85-M.
The contribution is (C) by Rudolf Marek.
Change-Id: I54fb1dcb0614452c775ed70d867ab44ff263a61a
Author: Rudolf Marek <r.marek@assembler.cz>
Signed-off-by: Idwer Vollering <vidwer@gmail.com>
Reviewed-on: http://review.coreboot.org/4559
Tested-by: build bot (Jenkins)
Reviewed-by: Rudolf Marek <r.marek@assembler.cz>
|
|
Ability to choose compatibility mode is interesting for testing payloads and
OS for compatibility with older systems.
As per comments
"ide_legacy_combined # TODO: Does nothing since
generations, remove from sb code?"
The "combined" mode was removed. It wasn't used by any mobo and the code for
it is almost identical to IDE one other than few bits relating to interrupt
handling and ISA mode.
Change-Id: I407a8fac753b513812a86bef5abcf39c6d81472e
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/4658
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Change-Id: I3c89bb633c32a2c2db349cb4fcbe1ed1c8deb5af
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/4657
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Number one reason to use cbfs_get_file was to get file length.
With previous patch no more need for this.
Change-Id: I330dda914d800c991757c5967b11963276ba9e00
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/4674
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Tested-by: build bot (Jenkins)
|
|
THis reduces risks of bufer overflows.
Change-Id: I77f80e76efec16ac0a0af83d76430a8126a7602d
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/4279
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
DRAM reset gate GPIO is different on different mobos move it to hidden config
with 60 (current value) as default.
Set it to 10 for Lenovo X201.
Change-Id: I4f3b6876d7c33d4966315091b63a76a9a0064c16
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/4622
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Options for selecting the USB port and controller for usbdebug
were unintentionally hidden with commit 8232bc2c on AGESA platforms
using cimx/sb700 or cimx/sb800.
Change-Id: Ibacc81a580519fe7fa86f08374046625327340b4
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/4607
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
|
|
Change-Id: Ib5bac45ee7aa5492c10fa97cd75b828b6192250d
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/4604
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
AMD fam10 raminit cannot be built without RAMINIT_SYSINFO, this
is not a true option but copy-paste remainder from AMD K8.
Change-Id: Id8edc112f3bacebd1732304ac9ee6e77cc6263b7
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/4581
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
The comment was copied around so fix all occurrences using the following
command.
$ git grep -l accessm | xargs sed -i 's/accessm/access/g'
Change-Id: I46e117c126c0f851cd5e95cf9e42a77ca5f80996
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/4577
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
The main purpose of option rom is to supply int* handlers.
But supplying those is outside of coreboot scope and if someone needs those
they should run SeaBIOS anyway which runs the option roms wonderfully.
Running VGA oprom is kept because they're needed to init graphics.
This patch still keeps the options to include the option roms to make them
available to SeaBIOS.
Change-Id: I646334cf88094d3bf8f527779a68a07e0b4b93ec
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/4545
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-by: Kevin O'Connor <kevin@koconnor.net>
|
|
Clean up superfluous line terminators.
Change-Id: If837b4f1b3e7702cbb09ba12f53ed788a8f31386
Signed-off-by: Idwer Vollering <vidwer@gmail.com>
Reviewed-on: http://review.coreboot.org/4562
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Tested-by: build bot (Jenkins)
|
|
Originally, Vortex86EX PCI S/B internal resource reservation functions can
only support one big legacy I/O device space (0-0xfff).
Change function signature to support other non-legacy I/O device space in
the future.
Change-Id: I22f5c877ed441d59f29801d925ee40b24fb796ce
Signed-off-by: Andrew Wu <arw@dmp.com.tw>
Reviewed-on: http://review.coreboot.org/3976
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
The end of the _PS0 method that is supposed to transition the
XHCI device to D0 state is instead putting it in D3 state.
This triggers a PME_B0 GPE which causes a Notify to the XHCI
ACPI Device in the kernel and that increments the wakeup counter
and causes aborted suspends.
Instead if we just leave the device in D0 where it should be
after executing this function then the PME_B0 is not generated
and the kernel does not see a wakeup on XHCI.
Similarly I changed the _PS3 method to always put the device in
D3 at the end of the method, rather than depending on the state
to be D3 at the start.
Before this change the kernel would see the following sequence
when trying to suspend when the XHCI controller is in D3cold:
kernel: ACPI: Execute Method [\_SB_.PCI0.XHCI._PS0] (Node ffff88017802bf28)
kernel: evmisc-0169 [07] ev_queue_notify_reques: Dispatching Notify on [XHCI] (Device) Value 0x02 (Device Wake) Node ffff88017802bc30
kernel: evmisc-0169 [07] ev_queue_notify_reques: Dispatching Notify on [EHCI] (Device) Value 0x02 (Device Wake) Node ffff88017802b8e8
kernel: evmisc-0169 [07] ev_queue_notify_reques: Dispatching Notify on [HDEF] (Device) Value 0x02 (Device Wake) Node ffff88017802b1b8
kernel: xhci_hcd 0000:00:14.0: power state changed by ACPI to D0
kernel: xhci_hcd 0000:00:14.0: PME# disabled
kernel: xhci_hcd 0000:00:14.0: enabling bus mastering
kernel: xhci_hcd 0000:00:14.0: setting latency timer to 64
kernel: PM: Wakeup pending, aborting suspend
kernel: last active wakeup source: 0000:00:14.0
Now it does not get a notification (due to PME_B0) when going to D0
on the way into suspend. XHCI goes from D3cold to D0 (in order to
be able to read mmio) and then back to D3hot before suspend.
kernel: ACPI: Execute Method [\_SB_.PCI0.XHCI._PS0] (Node ffff88017802bf28)
kernel: xhci_hcd 0000:00:14.0: power state changed by ACPI to D0
kernel: xhci_hcd 0000:00:14.0: PME# disabled
kernel: xhci_hcd 0000:00:14.0: enabling bus mastering
kernel: xhci_hcd 0000:00:14.0: setting latency timer to 64
kernel: ACPI: Execute Method [\_SB_.PCI0.XHCI._S3D] (Node ffff88017802c000)
kernel: xhci_hcd 0000:00:14.0: PME# enabled
kernel: xhci_hcd 0000:00:14.0: System wakeup enabled by ACPI
kernel: ACPI: Execute Method [\_SB_.PCI0.XHCI._PS3] (Node ffff88017802bf50)
kernel: xhci_hcd 0000:00:14.0: power state changed by ACPI to D3hot
Change-Id: Id5cd28eede2b27d97640047feb17349ae4ab79b7
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/65236
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4448
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
The coreboot and ACPI code that clears USB3 PORTSC change status
bits was not properly preserving the state of the PED (port enabled
or disabled) status bit, and it could write 0 back to this field
which would disable the port.
Additionally add back the code that resets disconnected USB3 ports
on the way into suspend (as stated in the BWG) but take care to
clear the PME status bit so we don't immediately wake.
suspend/resume with USB3 devices
1) suspend with no devices, plug in while suspended, then resume
and verify that the devices are detected
2) suspend with USB3 devices inserted, then suspend and resume
and verify that the devices are detected
3) suspend with USB3 devices inserted, then remove the devices
while suspended, resume and ensure they can be detected again
when inserted after resume
Change-Id: Ic7e8d375dfe645cf0dc1f041c3a3d09d0ead1a51
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/65733
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Commit-Queue: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4473
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
The recommended value in docs is D2, but lynxpoint XHCI does not even
support D2 state which causes the kernel to think this device cannot
be used as a wake source:
kernel: xhci_hcd 0000:00:14.0: System wakeup enabled by ACPI
kernel: ACPI: Device does not support D2
kernel: xhci_hcd 0000:00:14.0: System wakeup disabled by ACPI
Additionally this means the kernel will never put the device into D3
state by itself. There is SMI code that will put the device into D3
before suspend so advertising D3 here should be correct.
With this change the kernel will put the controller into D3 on suspend
and back to D0 on resume, including executing the ACPI methods
for _PS0/_PS3 that contain chipset specific workarounds.
In addition add a _PSC method to directly return the D state from the
device registers. With ALL USB devices removed the XHCI controller
goes into D3 state and the kernel can have a hard time determining
the state of the device at boot.
A kernel compiled with CONFIG_ACPI_DEBUG=y and module parameters
acpi.debug_layer=0x7f acpi.debug_level=0x2f can be used to see
what ACPI methods are executed:
kernel: xhci_hcd 0000:00:14.0: System wakeup enabled by ACPI
kernel: ACPI: Execute Method [\_SB_.PCI0.XHCI._PS3] (Node ffff8801000a7f50)
kernel: ACPI: Preparing to enter system sleep state S3
...
kernel: ACPI: Waking up from system sleep state S3
kernel: ACPI: Execute Method [\_SB_.PCI0.XHCI._PS0] (Node ffff8801000a7f28)
kernel: xhci_hcd 0000:00:14.0: power state changed by ACPI to D0
Change-Id: Ic64040eb4dd1947a1e2f0ee253a64be683e0ec70
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
meld with s3d
Change-Id: Ic6789720c4efe661dcb03a4afce8d88115854472
Reviewed-on: https://gerrit.chromium.org/gerrit/63916
Tested-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Commit-Queue: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/4409
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
- Put the device into D0 and not D3 so memory bar is available
and the subsequent commands actually do something useful
- Remove set of 818Ch[7:0]=FFh (gone in ref code)
- Fix reg 0x40/0x44 mixup
Verify that expected bits are set:
localhost ~ # pci_read32 0 0x14 0 0x10
0xe0500004
localhost ~ # mmio_read32 0xe0508144
0x000003ff
localhost ~ # mmio_read32 0xe050816c
0x000f0038
Change-Id: I388398e8c7d11e538ca18dab55d8bbd9b88f17df
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/63801
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4408
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
This commit adds a new Kconfig option for the LynxPoint
southbridge that will have coreboot route all of the USB
ports to the XHCI controller in the finalize step (i.e.
after the bootloader) and disable the EHCI controller(s).
Additionally when doing this the XHCI USB3 ports need
to be put into an expected state on resume in order to make
the kernel state machine happy.
Part of this could also be done in depthcharge but there
are also some resume-time steps required so it makes sense
to keep it all together in coreboot.
This can theoretically save ~100mW at runtime.
Verify that the EHCI controller is not found in Linux and
that booting from USB still works.
Change-Id: I3ddfecc0ab12a4302e6034ea8d13ccd8ea2a655d
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/63802
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4407
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Move this to the existing USB source files so they can share some
helper functions and keep the main smihandler code cleaner.
The XHCI sleep prepare code now implements the actual sleep
preparation steps from the ref code instead of the docs.
Change-Id: Ic90adbdaba947a6b53824e548c785b4fb3990ab5
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/63800
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4406
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Allow DTLE DATA / EDGE registers to be configured in board-specific
devicetree.
Change-Id: I82307d08c9cf73461db3ac7fb875a4fe70d6f9ea
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/65716
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-on: http://review.coreboot.org/4475
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
These programming sequences were changed in the latest code.
Change-Id: Ia4b763a49542635713d11a9ee81f7e7f200bf841
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/65612
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4466
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
The PCIe root port has ASPM settings/workarounds that are only applied
based on the value of an undocumented bit in PCI config register 0x32C.
If that bit is not set for some reason then the settings are not applied.
This devicetree config option will force the ASPM settings for each port
based on the bit map.
Change-Id: I40b08ca9a0ef52742609bac72fb821454a373799
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/65314
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4453
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
The default ME output is quite verbose and not all that useful
unless you are actively debugging the ME and then you can enable
the CONFIG_DEBUG_INTEL_ME option.
This commit silences the firmware capabilities and the MBP output.
Change-Id: I2b8abcb34ae0d00d9a38d029979e84ee0d0ca287
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/65252
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4452
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
This message allows unused clocks to be disabled based on a
devicetree setting in each mainboard.
Change-Id: Ib1988cab3748490cf24028752562c64ccbce2054
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/65250
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4450
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
The original ME code was assuming that the only type of messages
it would send were MKHI type and so it had some embedded checks
for that header and that type of message.
In order to support ICC messages this needs to change to handle
different header types, so now the header will be sent first
and then the data will follow, rather than the two both being
sent in the same low-level function.
This change has no real affect on the system, subsequent commit
will add new ICC messages.
Change-Id: I52848581e49b88c0a79e8bb6bda2a179419808a3
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/65249
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4449
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
The management engine is occasionally hanging the system on resume
when it is accessed. Since we actually don't need to do anything
with it on resume it can be disabled early in the resume path and
avoid assigning resources just to remove them later.
suspend/resume on falco and check /sys/firmware/log
to ensure that device 00:16.0 is disabled early and that no
resources are probed or assigned and that the device init path
does not execute.
Change-Id: I35573681e3a1d43d816d24954842cbe9c61f3484
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/62897
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4376
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
The management engine is slow, requiring at least 500ms between
when the Dram Init Done message is sent (right after memory training)
to when the MBP will report that it is successfully cleared and
that the ME can finally be sent the EOP message.
Currently this is adding 100-150ms to the boot time. If we defer
waiting for the MBP Clear indicator until the finalize step we
can gain back that lost time.
boot on falco with SMI debugging enabled to
ensure that the ME is locked down in the finalize step:
Finalizing Coreboot
SMI# #0
SMI_STS: PM1 APM
ME: MBP cleared
ME: mkhi_end_of_post
ME: END OF POST message successful (0)
Change-Id: Icab4c8c8e00eea67bed5e8154d91a1eb48a492d1
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/62633
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4375
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
There are specific programming requirements for the usb3 ports
on all LynxPoint chipsets when transitioning to D0 or D3.
LynxPoint-LP has additional workaround steps needed involving
resetting the disconnected ports when transitioning to D0.
The workarounds are implemented in ACPI code so the controller
can transition properly into D3 at runtime.
Change-Id: I3b428562f48c9cb250b97779a3b2753ed4f81509
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/62632
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4374
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
