| Age | Commit message (Collapse) | Author |
|---|
|
The management engine is occasionally hanging the system on resume
when it is accessed. Since we actually don't need to do anything
with it on resume it can be disabled early in the resume path and
avoid assigning resources just to remove them later.
suspend/resume on falco and check /sys/firmware/log
to ensure that device 00:16.0 is disabled early and that no
resources are probed or assigned and that the device init path
does not execute.
Change-Id: I35573681e3a1d43d816d24954842cbe9c61f3484
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/62897
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4376
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
The management engine is slow, requiring at least 500ms between
when the Dram Init Done message is sent (right after memory training)
to when the MBP will report that it is successfully cleared and
that the ME can finally be sent the EOP message.
Currently this is adding 100-150ms to the boot time. If we defer
waiting for the MBP Clear indicator until the finalize step we
can gain back that lost time.
boot on falco with SMI debugging enabled to
ensure that the ME is locked down in the finalize step:
Finalizing Coreboot
SMI# #0
SMI_STS: PM1 APM
ME: MBP cleared
ME: mkhi_end_of_post
ME: END OF POST message successful (0)
Change-Id: Icab4c8c8e00eea67bed5e8154d91a1eb48a492d1
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/62633
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4375
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
There are specific programming requirements for the usb3 ports
on all LynxPoint chipsets when transitioning to D0 or D3.
LynxPoint-LP has additional workaround steps needed involving
resetting the disconnected ports when transitioning to D0.
The workarounds are implemented in ACPI code so the controller
can transition properly into D3 at runtime.
Change-Id: I3b428562f48c9cb250b97779a3b2753ed4f81509
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/62632
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4374
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
This reverts commit ff81f50f0e4c068b64c4a5c7f5244196ecd24965.
Deferring this step until the finalize stage will allow us
to defer waiting for the MBP clear indicator and speeding
up the boot.
Change-Id: Ib8edffd06689e72875830cd68b5aedb7ac3b0559
Reviewed-on: https://gerrit.chromium.org/gerrit/62631
Tested-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Commit-Queue: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/4373
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Updated from 161 ref code
Change-Id: I3e07935fec1df21f14d97d165792fe54bf9e474c
Reviewed-on: https://gerrit.chromium.org/gerrit/62128
Tested-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Stefan Reinauer <reinauer@google.com>
Commit-Queue: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/4372
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
This is needed for SMBUS drivers to write to devices.
It was copied from existing intel southbridge driver.
Change-Id: Id0ce2393b2946a9c741413bca563a1a4dc0a4f5e
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/61893
Reviewed-on: http://review.coreboot.org/4364
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
The LynxPoint-LP chipset only has one EHCI controller so we should
not attempt to write into the second one that only exists on LynxPoint-H.
Change-Id: I1eae060c7f0a5873c9684e5abfeea5cb5895ab62
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/63799
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4405
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
The SystemAgent contains a mini-hd audio controller at PCI 0:3.0
which uses the same verb table init sequence as the southbridge.
In order to avoid two copies of the verb table loading code I
separated out the HDA verb table functions into a file that can
be re-used and then added a minihd driver to the haswell northbridge.
The minihd verb table is the same across devices so it can live
within the minihd driver rather than needing to be specified in
each separate mainboard.
I also fixed up the driver for lynxpoint HDA by following the
reference code.
Without HDMI cable plugged in driver does not find any codec,
and it does not seem to re-probe when HDMI is connected. We may
be missing kernel patches for this.
hda-intel 0000:00:03.0: no codecs found!
With a basic kernel patch to add 0x0a0c device ID to HDA driver
and with HDMI cable connected it is much happier:
snd_hda_intel 0000:00:03.0: irq 60 for MSI/MSI-X
input: HDA Intel MID HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:03.0/sound/card0/input9
snd_hda_intel 0000:00:1b.0: irq 61 for MSI/MSI-X
input: HDA Intel PCH Mic as /devices/pci0000:00/0000:00:1b.0/sound/card1/input10
input: HDA Intel PCH Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card1/input11
Change-Id: Ifa587984be4fc2801704a0368b9cdf8379c2450e
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/59336
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4318
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
To save power, disable audio codec in S3 + S5.
Also, refactor Lynxpoint GPIO code slightly to allow usage in SMM
binary.
Change-Id: I55c4248c89a258b5e4cecf8579eb58f1c15430c0
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/60950
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4339
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Some files have incorrect/odd permissions,
correct them: remove unnecessary +x flags.
Change-Id: I784e6e599dfee88239f85bb58323aae9e40fb21c
Signed-off-by: Idwer Vollering <vidwer@gmail.com>
Reviewed-on: http://review.coreboot.org/4490
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Bruce Griffith <Bruce.Griffith@se-eng.com>
|
|
No need to show the choice of USB port or controller in case of older
hardware where location for usbdebug was hardwired.
Change-Id: Ia186bf2c6ed60be2834cf6fd0a1965c8bf81ed4d
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/4290
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
- updates from 1.6.0 ref code
- remove the step comments as they are no longer even close
- add constants for LPT revisions
build and boot on Falco
Check that RCBA+2300[1] is set:
> mmio_read32 0xfed1e300
0x00000002
Change-Id: I8b3c5fda3f3170455699a7834239cb991603e7a8
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/59821
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4326
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Implement the LynxPoint BIOS Spec for clock gating.
Change-Id: Iaa84cb447bd29b0d13cdda481a1661ea40499de1
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/59590
Reviewed-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/4325
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
There's a need to determine if a specific gpio pin is
is set up to be a native function or not. Implement this.
Change-Id: I91d57a549e0f4fddc0b1849e5f74320fc839642c
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/59589
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/4324
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
The BIOS spec for LynxPoint calls out additional
programming steps for the PCIe Root Ports. Implement those
steps from the BIOS spec. These steps are completed before
deeper PCIe probing. The "late" programming was removed as
that was applicable to Cougar/Panther point where this
code was originally copied, though there was some overlap.
Change-Id: I64f25e4451e035d98ca6b66b0335bd280b70b074
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/59558
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/4323
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
PCIe Root Ports should be disabled based on pin ownership
and the strapping configuration. Implement this logic
for LynxPoint. The chip_ops->enable_dev() path is no
longer used. Instead the PCIe driver handles the enabling
and disabling of devices. This allows for having an empty
or incomplete device tree since those "allocated" devices
do not travel through the chip_ops->enable_dev() path.
The coalescing was tested to be working properly, however
not all configurations were tested.
Change-Id: I1e8bfe5e447b72ff8a4b04b650982d8c1ae0823c
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/59424
Reviewed-by: Stefan Reinauer <reinauer@chromium.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/4322
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
mainboard_smi_gpi has recently been updated to take a u32 argument from a
u16, but the patch introducing the fsp_bd82x6x support has been verified
on a master before this change, thus resulting in a 'cast from incompatible
type' error. Update the pointer to the correct size argument.
Change-Id: I9d62ee43f7c8ed774898f54d29a87cf463b76e91
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-on: http://review.coreboot.org/4479
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
|
|
Add support for the bd82x6x using the Intel FSP.
The FSP is different enough to warrant its own source files
for now. The mrc/system agent chromebook solution does much more
southbridge initialization and configuration than the FSP version.
It may be combined in the future.
Change-Id: Ie493945f3d321d854728d231979a0c172d2b36de
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-on: http://review.coreboot.org/4017
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Ibexpeak shares few files with bd82x6x. In order for it to work correctly
their config structures from chip.h must match, so include bd82x6x/chip.h
in ibexpeak/chip.h
Change-Id: Ib56b311b8af04f4e4803d1834724680f604901cd
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/4277
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
LynxPoint-LP has a lot of GPEs and the "default" set has been
moved to register 4 starting at bit offset 96. This means
that PME_B0 bit in GPE0_EN/GPE0_STS is now bit 109 in LPT-LP
but still bit 13 in LPT-H.
suspend on falco and wake from usb
4 | 2013-06-19 10:49:17 | ACPI Enter | S3
5 | 2013-06-19 10:49:22 | ACPI Wake | S3
6 | 2013-06-19 10:49:22 | Wake Source | Internal PME | 0
Change-Id: I443cd4d17796888debed70c0bda27ae09accd09b
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/59265
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4253
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
|
|
Do not directly check the return value of get_option, but instead compare
the returned value against a CB_CMOS_ error code, or against CB_SUCCESS.
Change-Id: I2fa7761d13ebb5e9b4606076991a43f18ae370ad
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-on: http://review.coreboot.org/4266
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Some of the pcie logic was located in pch.c as well
as pcie.c. Move all pcie logic to the same pcie.c
file. This is a straight cut-and-paste (no logic changes)
except for a rename from pch_pcie_enable() ->
pch_pcie_enable_dev().
Change-Id: I338c53039b95f255ab9ced313c51193a9d34b404
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/59277
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/4251
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
The function to disable devices was formerly named
pch_hide_devfn(). This routine was doing more than hiding
devices. It was disabling them, i.e. turning them off.
Therefore, rename it to pch_disable_devfn(). Also, allow
external callers to this function.
Change-Id: Id5bb319d4e67892c02a39dff49e45b2811a2f016
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/59276
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/4250
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
The iobp functions are useful to may of the southbridge
devices as certain values need to be updated to properly
initialize the devices. Therefore expose read, write, and
updated iobp functions.
Change-Id: Id7fdd8d0d9f022f92d6285ecd8f85a52024ec2bb
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/59275
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/4249
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
There are useful values in NVS that are set at boot
and runtime and they should not be cleared on resume.
suspend/resume twice on slippy and ensure
that the USB ports are still powered on the second suspend.
Change-Id: I4bce60b02b6637f6683120ae9c4a5c64563aacf7
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/56941
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4210
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
If Vortex86EX PS/2 keyboard controller system flag bit times out,
reload controller firmware code and try again.
Abort and die after 11 tries as this means the CPU is defect. Also
inform the user by printing a message.
Change-Id: I24aec4b20d85c721c01e72686f3eb1259f9334b8
Signed-off-by: Andrew Wu <arw@dmp.com.tw>
Reviewed-on: http://review.coreboot.org/3988
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
|
|
Previously, I've set this config in mobo config, yet according to
Kyösti Mälkki this parameter is southbridge-specific and not
mobo-specific.
Change-Id: I92428aed5a69d88a371f5d7267bc54ba7530766c
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/4276
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
|
|
The wake device input pins are active low and the
GPIOs need to be set as inverted when they are marked
as an input so they are not spuriously logged.
suspend/resume on slippy with trackpad wake:
8 | 2013-05-29 07:43:14 | ACPI Enter | S3
9 | 2013-05-29 07:43:18 | ACPI Wake | S3
10 | 2013-05-29 07:43:18 | Wake Source | GPIO | 12
and with power button wake:
11 | 2013-05-29 07:43:35 | ACPI Enter | S3
12 | 2013-05-29 07:43:40 | EC Event | Power Button
13 | 2013-05-29 07:43:40 | ACPI Wake | S3
14 | 2013-05-29 07:43:40 | Wake Source | Power Button | 0
Change-Id: I15d38dcc9b2fb4b2b0eb27da358fa3c343e22323
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/56940
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4209
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Both EHCI and XHCI controllers have additional setup steps
that are not part of the PEI reference code so they need to
be done later.
Both controllers also have specific clock gating setup
requirements that are now implemented.
Additionally they both have specific requirements when entering
sleep states. XHCI needs something in S3/S4/S5 and EHCI only
has steps for S4/S5 entry.
Change-Id: Ic62cbc8b6255455e56b72dd5d52e27a311999330
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/57033
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4217
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
This is an LPT-LP specific method that will enable a specific
GPIO as an ACPI SCI wake source.
It can be used by a device _DSW method to enable a pin that is
otherwise not configured to generate SCI at runtime.
It will set:
- GPIO owner to ACPI
- GPIO route to SCI
- GPIO config to GPIO, Input, Inverted
Also clean up and remove ACPI field definitions that are unused
and/or incorrect.
Change-Id: I14acc2de50e6200f61c2898a7bd1252400e0f0be
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/56621
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4189
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
LynxPoint-LP has an additional 16 entries in the IOAPIC that
can be assigned to specific GPIOs when they are configured
as PIRQ.
The maximum redirection entries field in the IOAPIC needs to
be set to 0x27 when this is enabled.
Additionally specific GPIOs need to be routed to PIRQ so they
interrupt via the IOAPIC instead of the GPIO IRQ 14/15.
Change-Id: Ie587e1d203422ff6fb7fc5056d20a5ae66720991
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/56620
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4203
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
The ssdt2 generation code was calling acpigen_patch_len().
However, none of the entries had AML object lengths that
needed patching. That resulted in the following message:
ASSERTION FAILED: file 'src/arch/x86/boot/acpigen.c', line 52
Additionally, this caused an errant write to a memory address
whose value was in the variable ltop. This was the 0 address.
Change-Id: I44abf5a4e4225220575aee6b5c9bb6b0be093a28
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/56299
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/4182
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
The ACPI code was defining two EHCI controllers and ignoring
the XHCI controller. This changes the second EHCI controller
to be XHCI instead and changes the wake resource to indicate
S3 and not S4.
cat /proc/acpi/wakeup
Device S-state Status Sysfs node
HDEF S4 *disabled pci:0000:00:1b.0
EHCI S3 *enabled pci:0000:00:1d.0
XHCI S3 *enabled pci:0000:00:14.0
Change-Id: If28775e6ef8608c22c85ca91d91d1f598ec7755d
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/56263
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4181
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
The clock gating register at offset 0x800 is managed by the
clock driver in the kernel when the devices are in ACPI mode.
When in PCI mode we should force enable the clock here.
When in ACPI mode or the device is disabled it should be put
in D3Hot state.
> i2cdetect -y -r 10
0 1 2 3 4 5 6 7 8 9 a b c d e f
00: -- -- -- -- -- -- -- -- -- -- -- -- --
10: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
20: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
30: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
40: -- -- -- -- 44 -- -- -- -- -- -- -- -- -- -- --
50: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
60: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
70: -- -- -- -- -- -- -- --
Change-Id: Ib93ffd41bf36386d5ce63bfc0ae6597f3e23bc48
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/56122
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4180
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Enable GPIO SMI for GPIO34 and set it as inverted so it
is only generated when it is raised by the EC.
1) ec console command: lidopen
2) wait until booted to developer screen
3) ec console command: lidclose
4) ensure system turns off
Change-Id: I7d50f171f3f4539c7c264103d1ffc7c5d0f1c7ba
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/56052
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4177
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
The vendor ids were never updated to reflect LynxPoint's device
ids. Therefore, none of the initialization was being ran. Fix
this.
Change-Id: Ic6ec00c9fb1cbcb6087fd89b0acff3d83294ac6a
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/55821
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/4173
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
In order to report whether coreboot enabled a SerialIO device
in ACPI mode we had been relying on reading NVS in the _STA
method for the SerialIO device.
The ACPI _STA method has restrictions on what it can access
and is unable to access OperationRegions outside its scope
which means it should not be trying to read NVS.
This change adds a new SSDT to the ACPI tables and fills it
with constants that indicate whether or not a device is enabled
in ACPI mode.
The ACPI code is changed to read these variables from the
SSDT and use that instead of trying to query a variable in NVS.
Attempt to use lpt-clk driver to probe the
device clocks for SerialIO devices and see that the kernel
does not complain about accessing the GNVS region.
Change-Id: I8538bee4390daed4ecca679496ab0cb313f174ce
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/51369
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4170
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
- Disable EC software sync for now
- Report correct EC active firmware mode
- Force enable developer mode by default
- Set up PCH generic decode regions in romstage
- Pass the oprom_is_loaded flag into vboot handoff data
Change-Id: Ib7ab35e6897c19455cbeecba88160ae830ea7984
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/51155
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4169
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
In order to probe the gpio-lynxpoint kernel driver the
LP GPIO controller needs to be exposed as a specific
ACPI device.
This also allows the resources to be exposed to the OS via
this device instead of the catch-all LPC device.
Ensure the driver loads at boot:
gpiochip_find_base: found new base at 162
gpiochip_add: registered GPIOs 162 to 255 on device: INT33C7:00
Also ensure the driver is visible in sysfs:
$ cat /sys/devices/platform/INT33C7:00/gpio/gpiochip162/label
INT33C7:00
Change-Id: I9f79c008f88da9b67ed1cdfdb9d3a581ce8f05ff
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/50215
Reviewed-on: http://review.coreboot.org/4158
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Now that we have RW ramstage we don't need to have the
management engine lock down step done in a final SMM.
ME: mkhi_end_of_post
ME: END OF POST message successful (0)
PCI: 00:16.0: Disabling device
Change-Id: I9db4e72e38be58cc875c1622a966d8fcacc83280
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/49757
Reviewed-on: http://review.coreboot.org/4153
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
There were two undefined MBP types that are now defined.
These include NFC status and some interesting timing data.
ME: Wake Event to ME Reset: 6 ms
ME: ME Reset to Platform Reset: 7 ms
ME: Platform Reset to CPU Reset: 51 ms
Change-Id: I67bf1f303f3c32497041e64c40eb9ccb6a63d88a
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/49756
Reviewed-on: http://review.coreboot.org/4152
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Instead of having an OS re-parse cbmem book-keeping records
for the cbmem allocator just to get the console buffer export
the pointer to the memory console directly in a field named 'CBMC'.
This field lives in the GNVS table.
Change-Id: Ief0c4da7b18df66feb9c816c9f4abdf5a72bd3a4
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/49764
Reviewed-by: Stefan Reinauer <reinauer@chromium.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/4149
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Slight tweaks found when looking at latest ref code when
investigating package C-state issues.
A few bits in the clock gating register don't match the
documentation and are also cleaned up.
Change-Id: I36ced7280c160b114c70b2eeafc8b24813ff2f6a
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/49330
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4142
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Part of X201 port.
Change-Id: If17d707004aba9f08459dbd8f3a146fa3c076aa9
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/4052
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
|
|
This reads PCH power levels via PCODE mailbox and writes the
values into the PMSYNC registers as indicated in the BWG.
Change-Id: Iddcdef9b7deb6365f874f629599d1f7376c9a190
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/49329
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4143
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
This will be used in a later commit to do some specific
power sequencing.
Change-Id: Id7f033bb80aed915c2498ea910cb3ac7290da37f
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/48947
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4137
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
This adds some macros for the common GPIO defines and drops
the gpio number definition from each entry. The end result
is much easier to read. The wtm2 mainboard gpio list is modified
to use this.
Also fix a bug in the LP version of get_gpio() that was always
returning zero due to a miscompare.
Change-Id: I143e5aee412af1eda84e35f8026f31cf13df508e
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/48946
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4138
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
With the LynxPoint chipset there are more than 16
possible GPIOs that can trigger an SMI so we need
a mainboard handler that can support this.
There are only a handful of users of this function
so just change them all to use the new prototype.
Change-Id: I3d96da0397d6584f713fcf6003054b25c1c92939
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/49530
Reviewed-by: Stefan Reinauer <reinauer@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4145
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
- 0x200-0x208 for host command window
- 0x800-0x8ff for host command arguments and parameters
- 0x900-0x9ff for exported EC memory map
Change-Id: I064b969843ef0d3c602793d1cb3d82715775c05e
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/49755
Reviewed-on: http://review.coreboot.org/4151
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
|
|
Move into src/cpu/dmp/dmp_post_code.h
Change-Id: If9f4d842f352eb41618e71f49a226d3cc4ad0b46
Signed-off-by: Andrew Wu <arw@dmp.com.tw>
Reviewed-on: http://review.coreboot.org/3989
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Besides the AGESA static settings, the settings in mainboard/buildOpt.c also
change the final configuration. We need to make sure the settings in FchParam
in resume stage are the same as they were in cold boot stage, otherwise the
board can not wake up more than once.
Tested on AMD/Olive Hill, AMD/Parmer and ASRock/imb-a180.
(USB keyboard doesn't work when board wakes up. It is not introduced by this
patch. It needs more debugging.)
Change-Id: I5a5e5502080e358ffc3577dc6a40bb762844d998
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/3932
Tested-by: build bot (Jenkins)
Reviewed-by: Rudolf Marek <r.marek@assembler.cz>
|
|
Change-Id: I6bb652419a54b7b7190e417346581f38335425ae
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/3985
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Removing `-Wno-unused-but-set-variable` from `CFLAGS` the build for
QEMU Q35 and Roda RK9, both using the Intel 82801Ix southbridge, fail
with the following error.
src/southbridge/intel/i82801ix/lpc.c: In function 'i82801ix_enable_apic':
src/southbridge/intel/i82801ix/lpc.c:45:5: error: variable 'dummy' set but not used [-Werror=unused-but-set-variable]
cc1: all warnings being treated as errors
Removing `dummy` should be safe as GCC probably optimizes it away before
anyway. That no dummy variable is used for an RCBA [1] access in Intel
Lynx Point supports that this can be dropped safely.
[1] root complex base address
[2] src/southbridge/intel/lynxpoint/early_pch.c
Change-Id: I1c138a3498228dbd025f68d5e6af0acc29ed3460
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/3982
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
|
|
Don't check keyboard controller system flag until before calling
pc_keyboard_init(). This makes waiting time shorter.
Change-Id: I2cdb533a5b25575e1717434533a60decf748f6d8
Signed-off-by: Andrew Wu <arw@dmp.com.tw>
Reviewed-on: http://review.coreboot.org/3958
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
The main usbdebug file lib/usbdebug.c was removed from romstage
build with commit f8bf5a10 but the chipset-specific parts were not,
leading to unresolved symbol errors for AMD platforms.
Add a silent Kconfig variable USBDEBUG_IN_ROMSTAGE for convenient
use of this feature.
Change-Id: I0cd3fccf2612cf08497aa5c3750c89bf43ff69be
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3983
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
|
|
This is needed to apply a rule that get_top_of_ram() in romstage is
required to select HAVE_ACPI_RESUME, otherwise chipset/board has no
means to backup low memory to CBMEM on s3 resume.
Only board affected is asus/p2b.
Change-Id: Ia5cbf4e5e40af25f52a19de584d8bc5370487154
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3971
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
|
|
Linux unhelpfully "fixes" the value in PCI_BASE_ADDRESS_1 when it is
0xfec00000 (that is, outside the range of bus 0 address space). This
causes IOAPIC interrupts to fail to work under Linux. This issue was
originally unnoticed by me when testing as sanity checking such as
this is not done by NetBSD.
Hiding the IOAPIC BAR is done by the OEM BIOS on the ck804 boards I've
checked.
Change-Id: I736db163750f709d68c988fac075597a50b29ab7
Signed-off-by: Jonathan A. Kollasch <jakllsch@kollasch.net>
Reviewed-on: http://review.coreboot.org/3963
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Change-Id: Ibdd438455a545aa9266b0fd893d5ff27124ab22c
Signed-off-by: Jonathan A. Kollasch <jakllsch@kollasch.net>
Reviewed-on: http://review.coreboot.org/3961
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Call pc_keyboard_init function in southbridge. It makes PS/2
keyboard work in coreinfo payload.
Change-Id: Idb79f87b09eeeade94e966fb8769dec7578e2cf5
Signed-off-by: Andrew Wu <arw@dmp.com.tw>
Reviewed-on: http://review.coreboot.org/3957
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Jonathan A. Kollasch <jakllsch@kollasch.net>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Change-Id: I752a4a890e1f610651a2c688cf42350ce8e9deaa
Signed-off-by: Jonathan A. Kollasch <jakllsch@kollasch.net>
Reviewed-on: http://review.coreboot.org/3962
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Qemu has the fw_cfg interface at 0x510, which conflicts with
power management base address in coreboot. Move the pmbase to a
non-conflicting address. No need to worry about speedstep, it
is not supported by qemu and isn't enabled in the qemu config.
Change-Id: I3e87d8301988028ca0ea7d96c08b4e26ac15a7c2
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-on: http://review.coreboot.org/3938
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Chipsets sb700 and sb800/hudson have more than one USB EHCI controller,
implement the selection logic using already existing Kconfig option.
Change-Id: I9e0df1669d73863c95c36a3a7fee40d58f6f097e
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3928
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Northbridge code includes these headers, so they all need to
have the same name to allow different combinations of northbridge
and southbridge. This changes the sb900 names to match sb700 &
sb800, and points agesa/family12 and amd/torpedo to the new file
names.
Change-Id: I7a654ce9ae591a636a56177f64fb8cb953b4b04f
Signed-off-by: Corey Osgood <corey.osgood@gmail.com>
Reviewed-on: http://review.coreboot.org/3825
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
This retrieves back the value stored with store_initial_timestamp()
in the bootblock for southbridge.
Change-Id: I377c823706c33ed65af023d20d2e4323edd31199
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3908
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-by: Aaron Durbin <adurbin@google.com>
|
|
Clean whitespace errors that have gotten past lint-stable-003-whitespace
and gerrit review.
Change-Id: Id76fc68e9d32d1b2b672d519b75cdc80cc4f1ad9
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3920
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Bruce Griffith <Bruce.Griffith@se-eng.com>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
AMD northbridges have a complex way to resolve top_of_ram.
Once it is resolved, it is stored in NVRAM to be used on resume.
TODO: Redesign these get_top_of_ram() functions from scratch.
Change-Id: I3cceb7e9b8b07620dacf138e99f98dc818c65341
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3557
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
|
|
Now that MMCONF_SUPPORT_DEFAULT is enabled by default remove
the pcie explicit accesses. The default config accesses use
MMIO.
Change-Id: I46e69154cf576ddb642c34b6dd2bc0d27cc19b7e
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3811
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
|
|
Now that MMCONF_SUPPORT_DEFAULT is enabled by default remove
the pcie explicit accesses. The default config accesses use
MMIO.
Change-Id: Ie6776b04ca0ddb89a0843c947f358db267ac4a70
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3809
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Keep the EHCI BAR unchanged to keep usbdebug working.
Change-Id: I7fe0eed24a66cb5058b49ee3fc0350d91089ed7a
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3477
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
|
|
Add option to choose one of the EHCI controllers in recent
intel chipsets for usbdebug use.
Since EHCI controller function changes from 0:1d.7 to 0:1d.0 in
rcba_config() for some mainboards, check the PCI class code
for match.
Change-Id: I18a78bf875427c163c857c6f0888935c1d2a58d4
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3440
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
|
|
Nowadays, chipsets or boards do not only have one USB port with the
capabilities of a debug port but several ones. Some of these ports are
easier accessible than others, so making them configurable is also necessary.
This change adds infrastructure to switch between EHCI controllers,
but does not implement it for any chipset.
Change-Id: I079643870104fbc64091a54e1bfd56ad24422c9f
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3438
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
|
|
On AMD platforms, setting of USBDEBUG_DEFAULT_PORT=0 tries to scan
all physical ports one after other in incrementing order. To avoid
possible problems with other USB devices, one can select the port
number here and bypass the scan.
Intel platforms can communicate with usbdebug dongle on one
physical port only, and this option makes no difference there.
Change-Id: I45be6cc3aa91b74650eda2d444c9fcad39d58897
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3872
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
|
|
src/southbridge/amd/agesa/hudson/Kconfig config default value,
mainboard Kconfig config value for specific mainboard.
bit 1,0 - pin 0
bit 3,2 - pin 1
bit 5,4 - pin 2
bit 7,6 - pin 3
Change-Id: I54a87cf734685515a3e1850838ca7d94387172ce
Signed-off-by: WANG Siyuan <SiYuan.Wang@amd.com>
Signed-off-by: WANG Siyuan <wangsiyuanbuaa@gmail.com>
Reviewed-on: http://review.coreboot.org/3879
Tested-by: build bot (Jenkins)
Reviewed-by: Bruce Griffith <Bruce.Griffith@se-eng.com>
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
|
|
Change the defines, as follow-up patch will replace use of
constant CONFIG_EHCI_BAR.
Change-Id: I44ff77cb7a2826f3b43d8d46440fd4482a29d18c
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3875
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
|
|
Declare the functions that may be used in both romstage and ramstage
with simple device model. This will later allow to define PCI access
functions for ramstage using the inlined functions from romstage.
Change-Id: I32ff622883ceee4628e6b1b01023b970e379113f
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3508
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
|
|
Letting SMI handler touch EHCI controller is an excellent source
of USB problems. Remove usbdebug entirely from SMM.
It may be possible to make usbdebug console work from SMM
after hard work and coordination with payloads and even
OS drivers. But we are not there.
Change-Id: Id50586758ee06e8d76e682dc6f64f756ab5b79f5
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3858
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Tested-by: build bot (Jenkins)
|
|
Change-Id: Ic7d793754a8b59623b49b7a88c09b5c6b6ef2cf0
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/3768
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Change-Id: Ia2dff49d3e2b086546785d992f2d92bcf4d1ef1c
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Reviewed-on: http://review.coreboot.org/3376
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
The _OSC method is used to tell the OS what capabilities it can
take control over from the firmware. This method is described
in chapter 6.2.9 of the ACPI spec v3.0. The method takes 4
inputs (UUID, Rev ID, Input Count, and Capabilities Buffer) and
returns a Capabilites Buffer the same size as the input Buffer.
This Buffer is generally 3 Dwords long consisting of an Errors
Dword, a Supported Capabilities Dword, and a Control Dword.
The OS will request control of certain capabilities and the
firmware must grant or deny control of those features. We do not
want to have control over anything so let the OS control as much
as it can.
The _OSC method is required for PCIe devices. During Linux boot,
an error is logged to dmesg if _OSC is not found.
Change-Id: Icf6e7a82284d03d23fd30ee7b7db17754e988c9a
Signed-off-by: Mike Loptien <mike.loptien@se-eng.com>
Reviewed-on: http://review.coreboot.org/3823
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Adding the 'WordBusNumber' macro to the PCI0
CRES ResourceTemplate in the AMD FCH ACPI code.
This sets up the bus number for the PCI0 device
and the secondary bus number in the CRS method.
This change came in response to a 'dmesg' error
which states:
'[FIRMWARE BUG]: ACPI: no secondary bus range in _CRS'
By adding the 'WordBusNumber' macro, ACPI can set
up a valid range for the PCIe downstream busses,
thereby relieving the Linux kernel from "guessing"
the valid range based off _BBN or assuming [0-0xFF].
The Linux kernel code that checks this bus range is
in `drivers/acpi/pci_root.c`. PCI busses can have
up to 256 secondary busses connected to them via
a PCI-PCI bridge. However, these busses do not
have to be sequentially numbered, so leaving out a
section of the range (eg. allowing [0-0x7F]) will
unnecessarily restrict the downstream busses.
Change-Id: Ib2d36f69a26b715798ef1ea17deb0905fa0cad87
Signed-off-by: Mike Loptien <mike.loptien@se-eng.com>
Reviewed-on: http://review.coreboot.org/3822
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Split the Family16 (Kabini) DSDT file into logical regions.
Olive Hill is the only mainboard and Kabini is the only NB/CPU
currently using Family16 AGESA code.
Change-Id: I9ef9a7245d14c59f664fc768d0ffa92ef5db7484
Signed-off-by: Mike Loptien <mike.loptien@se-eng.com>
Reviewed-on: http://review.coreboot.org/3821
Tested-by: build bot (Jenkins)
|
|
Hook this up into the DMP Vortex86EX. Before under Windows XP
the microphone did not work. With the new logic it does. Now
line-in,line-out and microphone all work.
The verb data table is generated by Realtek.
Change-Id: I1bcef898a15547c86c12c4b52ce0069d13e23c84
Signed-off-by: Andrew Wu <arw@dmp.com.tw>
Reviewed-on: http://review.coreboot.org/3855
Tested-by: build bot (Jenkins)
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
|
|
codec_init expects wait_for_valid returns -1 for timeout, not 1.
Change-Id: I0f2a3ebb1934d0adaf13765434526bbc9efca9a3
Signed-off-by: Andrew Wu <arw@dmp.com.tw>
Reviewed-on: http://review.coreboot.org/3843
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
These Kconfig entries were forgotten from the commit
that re-enabled usbdebug for these southbridges.
Change-Id: Ia17f1dd3340408da7c033c2c949404d2636bed44
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3849
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
|
|
Now that MMCONF_SUPPORT_DEFAULT is enabled by default remove
the pcie explicit accesses. The default config accesses use
MMIO.
Change-Id: I58c4b021ac87a035ac2ec2b6b110b75e6d263ab4
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3810
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
|
|
Rearranged the F2A85-M DSDT file to match the functionality found
on Parmer. As with the Parmer implementation, the F2A85-M dsdt.asl
file in the mainboard directory contains only #include references to
the appropriate files.
As with Parmer, some include files have no content but are left as a
template for other platforms and as placeholders for completing the
ACPI implementation for F2A85-M.
Change-Id: Ic72cb6004538ca9d9f79826b9b3c8d6aeb25017c
Signed-off-by: Kimarie Hoot <kimarie.hoot@se-eng.com>
Reviewed-on: http://review.coreboot.org/3805
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin@se-eng.com>
|
|
Support code for sb700 and sb800 existed already, but Kconfig and
compile-time issues prevented from enabling USBDEBUG for boards
with the affected AMD southbridges.
Change-Id: I49e955fcc6e54927320b9dc7f62ea00c55c3cedf
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3439
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
|
|
With USBDEBUG selected, the file is built for both romstage and
ramstage. For the ramstage build, we need to explicitly use the
simple PCI config operations without devicetree.
Change-Id: I2de8d9c77bb458ba797c3aac9e2cd0d653e06684
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3437
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
|
|
This patch sets a bit in the Yangtze southbridge to enable
the extra protocol necessary to handle port multiplier chips.
This has been turned on during most of Kabini development
without any notable impact. Olive Hill has an optional daughter
board that incorporates Silicon Image Steel Vines chips. This
change has been tested with and without the daughter board. This
change can be regression tested using any Hudson-based motherboard,
although it has no impact on boards with discreet Hudson/Bolton
southbridges.
This was tested for impact on SATA performance in the absence of
a port multiplier using the IOZone benchmarks within the Phoronix
Test Suite. A SATA 3 hard drive (6.0 Gbps) and an SSD were
connected to the ports on Olive Hill without using the port
multiplier card. The test results contained more run-to-run
variation within the same configuration than was seen in the
aggregate results comparing the interface with and without the
port multiplier protocol additions. In other words, the test
had less accuracy than the impact caused by turning on port
multiplier support.
Change-Id: Ie87873b093f3e2a6a5c83b96ccb6c898d3e25f72
Signed-off-by: Bruce Griffith <bruce.griffith@se-eng.com>
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
Reviewed-on: http://review.coreboot.org/3808
Tested-by: build bot (Jenkins)
|
|
Yangtze uses Hudson AGESA wrapper code but has some changes.
The changes are necessary and have no effects on Hudson.
Change-Id: Iada90d34fdc2025bd14f566488ee12810a28ac0d
Signed-off-by: Siyuan Wang <SiYuan.Wang@amd.com>
Signed-off-by: Siyuan Wang <wangsiyuanbuaa@gmail.com>
Signed-off-by: Bruce Griffith <Bruce.Griffith@se-eng.com>
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
Tested-by: Bruce Griffith <bruce.griffith@se-eng.com>
Reviewed-on: http://review.coreboot.org/3783
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
|
|
Change-Id: I4ed9329126b216eb4ae58355672603ce79a6d4ef
Signed-off-by: Andrew Wu <arw@dmp.com.tw>
Reviewed-on: http://review.coreboot.org/3847
Tested-by: build bot (Jenkins)
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
|
|
Now that MMCONF_SUPPORT_DEFAULT is enabled by default remove
the pcie explicit accesses. The default config accesses use
MMIO.
Change-Id: I71923790aa03e51db01ae3a4745e1c44556d281f
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3812
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
|
|
The tests for __PRE_RAM__ or __SMM__ were repeatedly used
for detection if dev->ops in the devicetree are not available
and simple device model functions need be used.
If a source file build for ramstage had __PRE_RAM__ inserted
at the beginning, the struct device would no longer match the
allocation the object had taken. This problem is fixed by
replacing such cases with explicit __SIMPLE_DEVICE__.
Change-Id: Ib74c9b2d8753e6e37e1a23fcfaa2f3657790d4c0
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3555
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
|
|
Directory intel/common must be conditionally added in the list
of source directories, as the parent directory southbridge/intel
is unconditionally added even for boards without such device.
Change-Id: I7088bc6db9f56909ffa996aa7eff76cd72e177eb
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3827
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
|
|
Split the Parmer, Family 15tn, and Hudson DSDT into groups. This splits
the DSDT table into includable ASL files which carry details specific
to the Family 15tn APU, the Parmer platform, and the Hudson FCH. The
dsdt.asl file in the mainboard directory contains only #include
references to the appropriate files.
Initially, this split was done by moving each piece of functionality
into its own file (e.g. IRQ routing and mapping, processor tree, sleep
states and sleep methods, etc.) and those pieces were #included in
dsdt.asl to ensure an exact match (via acpidump/acpixtract/iasl -d)
with the extant version of the table. Once the new tables were found
to exactly match the existing tables, the pieces were rearranged into
reasonable groups (e.g. fch.asl, northbridge.asl, pci_int.asl, etc.).
Some include files have no content but are left as a template for
other platforms and as placeholders for completing the ACPI
implementation for Parmer (e.g. thermal.asl, superio.asl, ide.asl,
sata.asl, etc.).
Change-Id: I098b0c5ca27629da9bc1cff1e6ba9fa6703e2710
Signed-off-by: Steve Goodrich <steve.goodrich@se-eng.com>
Reviewed-on: http://review.coreboot.org/3629
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
|
|
Change-Id: Ic6f6af6298fed2f41f140a7aa62dccf98bf60927
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/3572
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Routes IRQs for USB device, SPI1, MOTOR, HD audio, CAN bus.
Change-Id: I995a5c6d3ed6a7dca4f0d21545c928132ccbbc21
Signed-off-by: Andrew Wu <arw@dmp.com.tw>
Reviewed-on: http://review.coreboot.org/3725
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
These are not specific to Intel. Further work needs to be done to
combine these with MMCONF_SUPPORT in arch/io.h.
Change-Id: Id429db2df8d47433117c21133d80fc985b3e11e4
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3502
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Without that fix, and with CONFIG_SMM_TSEG, we have:
src/southbridge/intel/i82801gx/smihandler.c: In function 'southbridge_smi_sleep':
src/southbridge/intel/i82801gx/smihandler.c:340:3: error: implicit declaration of function 'smi_release_lock' [-Werror=implicit-function-declaration]
cc1: all warnings being treated as errors
make: *** [build/southbridge/intel/i82801gx/smihandler.smm.o] Error 1
The fix is modelled after src/cpu/x86/smm/smihandler.c which
ifdefs smi_release_lock().
Change-Id: Icdc6d039b34a1d95d0e607419bba2484d21abc5e
Signed-off-by: Denis 'GNUtoo' Carikli <GNUtoo@no-log.org>
Reviewed-on: http://review.coreboot.org/3281
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Change-Id: Ic725b169061bd426aa8206dc1d6d31e67cc639f2
Signed-off-by: Denis 'GNUtoo' Carikli <GNUtoo@no-log.org>
Reviewed-on: http://review.coreboot.org/3304
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
