| Age | Commit message (Collapse) | Author |
|---|
|
CPUs with configurable TDP will run the TSC at the max non-turbo
ratio for the maximum TDP value, which can cause issues if another
TDP is desired. To deal with this we set the flex ratio to the
nominal TDP ratio early in the boot and then configure the Soft
Reset Data registers so the PCH can tell the CPU what frequency
to run at after a reset.
This is done very early in the bootblock because it is necessary
to reset the system after setting a flex ratio.
The end result is that the TSC will now increment at the max
non-turbo frequency for the nominal TDP.
On some system with 1.8GHz CPU ensure that the kernel
detects the CPU speed as ~1800mhz rather than ~2300mhz:
> dmesg | grep "MHz processor"
[ 0.004000] Detected 1795.801 MHz processor.
Change-Id: I8436dced9199003b6423186a2b041e3f7b84ab8c
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: http://review.coreboot.org/1329
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
There are enough differences that it is worth defining the
proper map for the sandybridge/ivybridge CPUs. The state
save map was not being addressed properly for TSEG and
needs to use the right offset instead of pointing in ASEG.
To do this properly add a required southbridge export to
return the TSEG base and use that where appropriate.
Change-Id: Idad153ed6c07d2633cb3d53eddd433a3df490834
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1309
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
- add Kconfig option for CONFIG_SPI_FLASH_SMM
- compile subsystem and chip drivers for smm if enabled
- change mdelay(1) to udelay(500) since mdelay is not defined
in SMM and a 1ms delay is worth avoiding
- make flash chip structure non-const so the probe function
pointers can be relocated for use in TSEG
- Make SMM PCI access possible in southbridge SPI code
Change-Id: Icfcbbe8e4e56658769d46af0b5bf6c79a6432641
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1313
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
The ME needs to be talked to through the PCIe memory mapped config
space.
Change-Id: Ic2c5a572a126722a08a82d95df13d11507586c6b
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1284
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
In the short term there might be devices with Sandy Bridge CPUs
on mainboards with Panther Point PCHes. While this configuration
option is perfectly valid, coreboot currently ties Sandy Bridge to
Cougar Point and Ivy Bridge to Panther Point. One occurence is in
the ME handling code.
To make coreboot most flexible, compile both ME handlers into
coreboot and decide at runtime which one to use.
Change-Id: Icffe2930873f67c99c3f73e37e7a967f4f002b88
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1280
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
- On Cougar Point there may have been stack corruption during the
ME hash verification
- On Panther Point the ME firmware hash was not passed on to the
OS
Change-Id: I73fc10db63ecff939833fb856a6da1e394155043
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1279
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
The PCIe device enable function prints when it disables a device.
The PCIe ports(bridges) use a different routine that didn't print
the message. Add it to be consistent and to provide better debug
output.
Change-Id: I8462c48e7f4930db68703f0bfb710c01c9643a98
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-on: http://review.coreboot.org/1326
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Tested-by: build bot (Jenkins)
|
|
Changing CMOS value for power-on-after-power-fail was only honored
after reboot, which is counter intuitive (set from "enable" to
"disable",
power-off, replug device -> device turns on; and similar cases).
Modelled after http://review.coreboot.org/#/c/444
Change-Id: I2b8461dff1ae085c1ea4b4926084268b4da90321
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1323
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
The function was too eager shifting stuff around, this change corrects
the problem.
Change-Id: I4c13dbe86cb627835dae05bb74af9867c28e143d
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: http://review.coreboot.org/1291
Tested-by: build bot (Jenkins)
|
|
There are enough subtle differences in the magic values that
it is easier to make a separate function.
This fixes a reset hang with pantherpoint chipset.
Change-Id: I02b03cb37e5fd5ee2fd62067644f0a62dc2cd26a
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1322
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
|
|
This makes it available early in romstage without having to
worry when the different romstagse enable it.
Check for extended CMOS to be enabled in early romstage.
This is used by a later commit which uses the extended
CMOS region for stoage.
Change-Id: I9e026d48499c63d6503c2b020d4cc3047126fa93
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1306
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
- Convert all PCI ID lists to new scheme
- Unify code (variable names)
- add missing PCI IDs for Panther Point PCIe root ports.
Change-Id: I6357f6ebce7ddffe45a3ec642b0c594147f6134c
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1301
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
This lets the SPI driver and the LPC driver know about HM70 and NM70.
Change-Id: Id2f1e0e5586a2f7200b2d24785df3f2be890da98
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1300
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
With this patch it is possible to use the smbus in ramstage. The
biggest part of the patch is a simple code split into a general
part (smbus.h) and the concrete users (early_smbus.c and cs5536.c).
After the switch from romstage to ramstage the smb base address
has changed, but that is no problem as the new base address is
stored in bar0 of the ISA bridge. It could also be read via msr,
but via PCI it is simpler. I used the following patch as
reference on how to readout the new base address:
http://lists.laptop.org/pipermail/commits-kernel/2006-November/000178.html
Change-Id: I9f86a1e474368c62f9ed3a95edfb3e63117aa156
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Reviewed-on: http://review.coreboot.org/1243
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
We don't ever free memory in coreboot, hence drop spi_flash_free() and
spi_free_slave()
Change-Id: I0ca3f78574ceb4516e7d33c06ab1a58abfb3b0ec
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1273
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Set the default location of hudson firmware to 3rdparty.
Move UMA code from mainboard to northbridge.
Change-Id: I11afea0c7fd04aa84a629dc762704c42baf002df
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: zbao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/1241
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Use of the uma_memory_base and _size variables is very scattered.
Implementation of setup_uma_memory() will appear in each northbridge.
It should be possible to do this setup entirely in northbridge
code and get rid of the globals in a follow-up.
Change-Id: I07ccd98c55a6bcaa8294ad9704b88d7afb341456
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1204
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Hudson code has been integrated from CIMx to AGESA. This patch is about the wrapper.
Change-Id: I63d951982140b82a3a77a97eb3d55fc75fc0caa3
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: zbao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/1157
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
awk on Cygwin created the UTF-8 value for the 0xff code point,
which makes it two bytes wide. This broke the build.
Change-Id: I4937ae7ce1136ba7a76d05b42f9dd2771203175d
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/1164
Tested-by: build bot (Jenkins)
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
Reviewed-by: Peter Stuge <peter@stuge.se>
|
|
The wrapper for Trinity. Support S3. Parme is a example board.
Change-Id: Ib4f653b7562694177683e1e1ffdb27ea176aeaab
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: zbao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/1156
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Required for Supermicro X7DB8, which needs the FBDIMM clock generator
setup during romstage.
Change-Id: I30ca8354087e851487aee0614595782131d4d9bc
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-on: http://review.coreboot.org/1116
Tested-by: build bot (Jenkins)
|
|
i3100/i5000 have a second IOAPIC which handles IRQs for PCI-X.
Add code to enable it.
Change-Id: Ib447628f501b152c8adc9c7c89bd09b5615b9e5a
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-on: http://review.coreboot.org/1118
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
The constant value 0x100000000 is used in linker scripts to calculate
offsets from the end of 32-bit-addressed memory. There is nothing
wrong with it, but 32-bit versions of ld do the calculation wrong.
Change-Id: I4e27c6fd0c864b4d98f686588bf78c7aa48bcba8
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1129
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
|
|
- Add #define to allow the FADT PM Profile to be overridden.
- Change the location of the PMA_CNT_BLOCK_ADDRESS to match
current documentation.
- cst_cnt should be 0 if smi_cmd == 0
- add a couple of default access sizes.
- Add a couple of #define values for unsupported C2 & C3 entries.
- Add PM Profile override value into amd/persimmon platform.
This does not use the #defines in acpi.h so that the files that
include this don't all need to start including acpi.h.
Change-Id: Ib11ef8f9346d42fcf653fae6e2752d62a40a3094
Signed-off-by: Martin L Roth <martin@se-eng.com>
Reviewed-on: http://review.coreboot.org/1055
Tested-by: build bot (Jenkins)
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
Reviewed-by: Marc Jones <marcj303@gmail.com>
|
|
This change adds utility functions which allow to read any GPIO pin,
as well as a vector of GPIO pin values.
As presented, these functions will be available to Sandy Bridge and
Ivy Bridge systems only.
There is no error checking: trying to read GPIO pin number which
exceeds actual number of pins will return zero, trying to read GPIO
which is not actually configured as such will return unpredictable
value.
When reading a GPIO pin vector, the pin numbers are passed in an
array, terminated by -1. For instance, to read GPIO pins 4, 2, 15 as a
three bit number GPIO4 * 4 + GPIO2 * 2 + GPIO15 * 1, one should pass
pointer to array of {4, 2, 15, -1}.
Change-Id: I042c12dbcb3c46d14ed864a48fc37d54355ced7d
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: http://review.coreboot.org/1049
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Change-Id: I98b05d9e639eda880b6e8dc6398413d1f4f5e9c3
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1048
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Right now coreboot compilation fails when SPI flash debugging is
enabled. Fix it by using the right set of memory functions.
Change-Id: I5e372c4a5df53b4d46aaed9e251e5205ff68cb5b
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1044
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Experiments have shown that writing plain value of 6 at byte io
address of 0xcf9 causes the systems to reset and reboot reliably.
Change-Id: Ie900e4b4014cded868647372b027918b7ff72578
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: http://review.coreboot.org/1050
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Remove all the repeated sections of code in cbtypes.h and place it
in a common location. Add include dir in vendor code's Makefile.
Change-Id: Ida92c2a7a88e9520b84b0dcbbf37cd5c9f63f798
Signed-off-by: Vikram Narayanan <vikram186@gmail.com>
Reviewed-on: http://review.coreboot.org/912
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
|
|
The fadt legacy free logic was backwards.
Change-Id: Ieb21ef335f7514ced70248d0bf8668ddb73cf59f
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-on: http://review.coreboot.org/1030
Reviewed-by: Peter Stuge <peter@stuge.se>
Tested-by: build bot (Jenkins)
|
|
The FADT iapc_boot_arch indicates the available information
for accessing legacy devices. By default, the setting supports
legacy. LEGACY_FREE and/or the iapc_boot_arch field may be
customized.
Change-Id: I5679741e1f8db923d3c00b57f6a5d813550f3a5e
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-on: http://review.coreboot.org/1024
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Peter Stuge <peter@stuge.se>
|
|
The South Station recieved updates that fix a number of fadt problems.
South Station now uses the southbridge fadt.
Change-Id: Ib990a69a359a4b7eae3431bb4323acd537acda1d
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-on: http://review.coreboot.org/1021
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Peter Stuge <peter@stuge.se>
|
|
This driver is taken from u-boot and adapted to match
coreboot. It still contains some hacks and is ICH specific
at places.
Change-Id: I97dd8096f7db3b62f8f4f4e4d08bdee10d88f689
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/997
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Change source file modes from 755 to 644
The following files have been grepped for changes:
*.c
*.h
*Kconfig*
*Makefile*
Change-Id: I275f42ac7c4df894380d0492bca65c16a057376c
Signed-off-by: Alec Ari <neotheuser@ymail.com>
Reviewed-on: http://review.coreboot.org/1023
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
The fadt.c is the same across all the platforms using the sb800
cimx southbridge wrapper.
Change-Id: Ifbbfc238732aa46aef96297eaa188b77d27151f3
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-on: http://review.coreboot.org/1019
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
These are the PMIO & PMIO2 read & write routines from
src/southbridge/amd/sb800/sb800.c & sb800.h for use in the cimx
tree. Currently most platforms using CIMX are calling WritePMIO()
directly from the src/vendorcode/amd/cimx/sbX00 directories
instead of using a wrapper function.
These functions only do byte reads & writes.
Change-Id: I881a6e2d4ddbba3dbdf4dd33e06313fe88b3682a
Signed-off-by: Martin L Roth <martin@se-eng.com>
Reviewed-on: http://review.coreboot.org/981
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Replace #elif (CONFIG_FOO==1) with #elif CONFIG_FOO
find src -type f -exec sed -i "s,\(#.*\)(\(CONFIG_[A-Z0-9_]*\)[[:space:]]*==[[:space:]]1),\1\2,g" {} +
(manual tweak since it hit a false positive)
Replace #elif (CONFIG_FOO==0) with #elif !CONFIG_FOO
find src -type f -exec sed -i "s,\(#.*\)(\(CONFIG_[A-Z0-9_]*\)[[:space:]]*==[[:space:]]0),\1\!\2,g" {} +
Change-Id: I8f4ebf609740dfc53e79d5f1e60f9446364bb07d
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/1006
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-by: Martin Roth <martin@se-eng.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Replace #if CONFIG_FOO==1 with #if CONFIG_FOO:
find src -name \*.[ch] -exec sed -i "s,#if[[:space:]]*\(CONFIG_[A-Z0-9_]*\)[[:space:]]*==[[:space:]]*1[[:space:]]*\$,#if \1," {} +
Replace #if (CONFIG_FOO==1) with #if CONFIG_FOO:
find src -name \*.[ch] -exec sed -i "s,#if[[:space:]]*(\(CONFIG_[A-Z0-9_]*\)[[:space:]]*==[[:space:]]*1)[[:space:]]*\$,#if \1," {} +
Replace #if CONFIG_FOO==0 with #if !CONFIG_FOO:
find src -name \*.[ch] -exec sed -i "s,#if[[:space:]]*\(CONFIG_[A-Z0-9_]*\)[[:space:]]*==[[:space:]]*0[[:space:]]*\$,#if \!\1," {} +
Replace #if (CONFIG_FOO==0) with #if !CONFIG_FOO:
find src -name \*.[ch] -exec sed -i "s,#if[[:space:]]*(\(CONFIG_[A-Z0-9_]*\)[[:space:]]*==[[:space:]]*0)[[:space:]]*\$,#if \!\1," {} +
(and some manual changes to fix false positives)
Change-Id: Iac6ca7605a5f99885258cf1a9a2473a92de27c42
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/1004
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-by: Martin Roth <martin@se-eng.com>
|
|
The current early PM setup that attempts to configure dynamic clock
gating relies on PCIe functions to be enabled that may not be.
Instead of reading port 0 or 4 directly to determine the link width
use the register that refelects the soft strapping options as this
will always be available.
Also add a clear register assignment and break for port 0 in the
switch statement instead of falling through to port 4 as that could
end up setting the slot power limit based on port 4 values instead
of based on port 0.
register 0xE1=0x3f and all other root ports should have 0xE1=0x03.
When port 0 and 4 are disabled they will have 0xE1=0x3C before
being disabled by the pch enable handler.
LUMPY default:
00:1c.0 PCI bridge: Intel Corporation Device 1c10 (rev b5)
00:1c.3 PCI bridge: Intel Corporation Device 1c16 (rev b5)
pci_read8 0 0x1c 0 0xe1
0x3f
pci_read8 0 0x1c 3 0xe1
0x03
LUMPY with PCIe port coalesce enabled:
00:1c.0 PCI bridge: Intel Corporation Device 1c10 (rev b5)
00:1c.1 PCI bridge: Intel Corporation Device 1c16 (rev b5)
pci_read8 0 0x1c 0 0xe1
0x3f
pci_read8 0 0x1c 1 0xe1
0x03
Change-Id: I33a37b0ec0c8e570cf5d9dda2c06e0225fee135c
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/980
Tested-by: build bot (Jenkins)
|
|
Background: The PCI spec (3.0-3.2.2.3.4) requires that PCI devices
implement function 0. The Linux Kernel therefore will not enumerate
a PCI device if it does not present a valid config space at function 0.
If a board does not have anything connected to root port 0 and it is
desired to disable the unused ports in order to save power then this
will cause the other downstream PCIe devices to go missing as they
will not be enumerated.
Intel chipsets provide a way to map root port numbers to different PCI
function numbers, thereby avoiding this issue and allowing root port 0
to be turned off.
This change adds a new chip config option 'pcie_port_coalesce' that
will collapse the enabled root ports into a linear map starting at
zero. This option defaults to disabled as it can have a confusing
effect on the system as the declared static devicetree may not match
what is seen at runtime. This option is also forced on if the static
devicetree disables port 0.
When each root port is processed in the early enable stage it looks
for a lower numbered root port that has been disabled and then swaps
the two assigned function numbers.
However the mapping register is write-once so it has to keep track of
the proposed mapping changes until all ports have been processed
before writing out the final map value. At this point it also updates
the function numbers in the static device tree so they are consistent
with the new layout.
There are a few other closely related fixes in this change:
1) There is a power savings opportunity if an entire bank of ports
(0-3 or 4-7) are disabled. This was checking the chipset revision to
look for CougarPoint B1+ stepping and that was not passing on
PantherPoint where this should always be applied. To fix this I added
a function to determine the chipset type based on comparing the upper
byte of the device ID.
2) Apply the same chipset type check fix to the IOBP programming.
3) There is another power savings opportunity to enable dynamic clock
gating on shared PCIe resources which only applies to ports 0 and 4.
However if 0 or 4 is disabled then the later check to enable this
would fail as that device is already hidden.
LUMPY current:
00:1c.0 PCI bridge: Intel Corporation Device 1c10 (rev b5)
00:1c.3 PCI bridge: Intel Corporation Device 1c16 (rev b5)
01:00.0 Network controller: Atheros Communications Inc. Device 0030 (rev 01)
02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B
LUMPY with PCIe port coalesce enabled:
00:1c.0 PCI bridge: Intel Corporation Device 1c10 (rev b5)
00:1c.1 PCI bridge: Intel Corporation Device 1c16 (rev b5)
01:00.0 Network controller: Atheros Communications Inc. Device 0030 (rev 01)
02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B
Change-Id: I828aa407fdc9c156c1c42eda8e2d893c0aa66eef
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/979
Tested-by: build bot (Jenkins)
|
|
The chipset enforces static-defined interrupt swizzling on PCIe root
ports so if a port is remapped to a different function it needs to
still report the proper interrupt map to the OS instead of assuming
that function number is equivalent to root port number.
This change also includes an update to the PCH function disable
register which was incorrect for CPT/PPT and would cause unpredictable
behavior if used.
The kernel command line was changed to add 'nomsi' in order to force
PCIe devices to use IO-APIC assigned interrupts and not MSI to ensure
that the mapping is correct.
LUMPY current:
00:1c.0 PCI bridge: Intel Corporation Device 1c10 (rev b5)
00:1c.3 PCI bridge: Intel Corporation Device 1c16 (rev b5)
16: 41518 0 0 0 IO-APIC-fasteoi i915, ahci, ath9k
19: 720 0 0 0 IO-APIC-fasteoi ehci_hcd:usb2, eth0
LUMPY with PCIe port coalesce enabled:
00:1c.0 PCI bridge: Intel Corporation Device 1c10 (rev b5)
00:1c.1 PCI bridge: Intel Corporation Device 1c16 (rev b5)
16: 38988 0 0 0 IO-APIC-fasteoi i915, ahci, ath9k
19: 347 0 0 0 IO-APIC-fasteoi ehci_hcd:usb2, eth0
Change-Id: Ia5f6bb8888b5c38a5dbc88bb25ecdf1fca41ee3e
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/978
Tested-by: build bot (Jenkins)
|
|
The sata controller comes up in legacy/normal mode and
is currently put into AHCI mode in romstage.
If that is removed and the controller is left alone until the
ramstage driver (like we do on Stumpy/Lumpy) then the resource
allocator will have configured the device for IDE mode with an
IO address in BAR5. Then when the ramstage driver puts the
controller into AHCI mode it will not have the correct resources
to do the rest of the AHCI setup.
So the controller mode needs to be changed in the enable stage
rather than in the init phase. This same register contains
the port map and it is a R/WO (write once) field so the configured
port map must be written at the same time. For non-AHCI mode
the devicetree map was ignored before but it is used now.
Since the port map register is now written at enable step it
does not need to be written again during init.
With this change the sata port map can be reduced to just port 0
and then U-boot does not have to probe all available ports.
Change-Id: I977952cd88797ab4cea79202e832ecbb5c37e0bd
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/977
Tested-by: build bot (Jenkins)
|
|
The OS does not re-execute the APMC 'enable ACPI' SMI
on resume so this has the potential to leave things
in an unknown state.
Change-Id: Iaf0fcb99f699e9e0ecacaab3f529026782a95151
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/971
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
This adds the PCI device id of the LPC controller identifying the
QPRJ/QS stepping of the Panther Point southbridge.
Change-Id: Idcaa7dbd30224e3690ea469c6cb74f75de287631
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: http://review.coreboot.org/968
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Many PCI devices share the very same driver despite having different
PCI device IDs, which causes a lot of copy and paste of driver
definitions.
This change introduces a way to specify the array of acceptable
device IDs in a single driver entry. As an example the Intel
{Sandy|Ivy} Bridge SATA driver is being modified to use a single
driver structure for all different SATA controller flavors, a few
more Ivy Bridge IDs are being added as well.
BUG=none
TEST=manual
. modified coreboot brought up an Ivy Bridge platform all the
way to Linux login screen.
Change-Id: I761c5611b93ef946053783f7a755e6c456dd6991
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: http://review.coreboot.org/982
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
post_code() was added in our internal tree by duplicating code. It's not of
much use at this point, since the code is quite well tested, so avoid bloating
the bootblock (since compiled with ROMCC).
Also add some missing include files that didn't seem to be needed with an
older version of coreboot.
Change-Id: Id62b838728a247e8bcadb4f1db17269be0d4f3f4
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/936
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
rename from mainboard_apm_cnt to mainboard_smi_apmc to match the function
naming scheme of the other handlers. Add prototype for mainboard_smi_sleep
(mainboard specific S3 sleep handlers in SMM) that is required by Sandybridge.
Change-Id: Ib479397e460e33772d90d9d41dba267e4e7e3008
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/933
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Add early_smbus.c for romstage-y list and remove respective
include on mainboard romstage.c files.
Tested on AOpen board.
Change-Id: I1c7e6cb32e3a9d7cc9b6037dc27e59149d492001
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/909
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Made using coccinelle:
@@
expression E;
@@
-(E + 7) & -8
+ALIGN(E, 8)
@@
expression E;
@@
-(E + 15) & -16
+ALIGN(E, 16)
Change-Id: I071d2c98cd95580d7de21d256c31b6368a3dc70b
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/910
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
S3.rom is useless for all the other boards which don't use flash to
save sleep/wakeup settings. AGESA-based boards other than persimmon
haven't been validated the S3 resume. They don't need S3.rom yet.
Change-Id: I12693e9556ca6f8e0d80b2ab2dca5c85bdb97685
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: zbao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/902
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
echo -n isn't portable. echo -e isn't portable. that bash loop isn't portable.
So let's try something else.
Change-Id: Ie73aa1c09d90c11a5c4952a332d4c2058390b5db
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/889
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Zheng Bao <zheng.bao@amd.com>
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
1. Add some CIMX call for S3.
2. Detect sleep type.
Change-Id: I62888e8d8a03987ca88f5c935fa660f6b49a4fe9
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: zbao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/621
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Some places still hardcoded the address instead of using IO_APIC_ADDR.
Change-Id: I3941c1ff62972ce56a5bc466eab7134f901773d3
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/677
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Change-Id: Iac3cd25b36493bb203e849674320e113cc5fce32
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/853
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
It is for S3, storing the recovring data in the nonvolatile storage,
i.e., flash.
Change-Id: Ie9e4f42a80c93d92d2e442f0e833ce06d88294f9
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: zbao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/620
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
|
|
So far it just setups things right for Bifferboard. We may change it
in the future to fit other hardware.
Change-Id: I1c4ccff4e47b9cb9e31a738f038fc4f4ebe59087
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Reviewed-on: http://review.coreboot.org/808
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Changing CMOS value for power-on-after-power-fail was only honored
after reboot, which is counter intuitive (set from "enable" to "disable",
power-off, replug device -> device turns on; and similar cases).
Change-Id: If1d88c1c34c3333b636ed3ec1e1fb9bea394e615
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/444
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
We used a hard coded value for some reason. Don't do that, but use CMOS
instead.
Change-Id: Ib83aa07a3e55bed075150354a060317ebc9d5ba7
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/443
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Use separate Kconfig option to select a driver directory for
build and the specific type of southbridge to support.
Change-Id: I9482d4ea0f0234b9b7ff38144e45022ab95cf3f3
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/685
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Also mark the corresponding lint test stable.
Change-Id: Ib7c9ed88c5254bf56e68c01cdbd5ab91cd7bfc2f
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/772
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Southbridge SP5100 support was compiled with SB700 code, but static
device info structure would use sp5100/chip.h. To solve this drop
support for separate chip sp5100 and adjust the relevant Kconfig
options.
Removes chip directory:
src/southbridge/amd/sp5100/
Rename Kconfig option
from: SOUTHBRIDGE_AMD_SP5100
to: SOUTHBRIDGE_AMD_SUBTYPE_SP5100
Change-Id: I873c6ad3624ee69165da6ab7287dfb7e006ee8e8
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/679
Tested-by: build bot (Jenkins)
Reviewed-by: Zheng Bao <zheng.bao@amd.com>
Reviewed-by: Marc Jones <marcj303@gmail.com>
|
|
No in-tree board using that chipset has it not selected, so move
selection from boards to southbridge.
Change-Id: I16b27e40ca1a201b2f968f8ce303eaafe43804c0
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/660
Tested-by: build bot (Jenkins)
|
|
If PCI config cycles use MMIO instead of I/O in the SB600 bootblock
code the cycles will go nowhere since the MMIO feature hasn't been
configured yet. This change forces the cycles to use I/O and
configures the southbridge decode range to what is defined by the
mainboards Kconfig.
Change-Id: I85297237f32f37b3fc1ff5b488cca0a43bcf20fd
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: http://review.coreboot.org/632
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
If PCI config cycles use MMIO instead of I/O in the SB700
bootblock code the cycles will go nowhere since the MMIO feature
hasn't been configured yet. This change forces the cycles to use
I/O and configures the southbridge decode range to what is specified
by the mainboards Kconfig.
Change-Id: I15a89a27645edf594d14ef20f129f75a315e9672
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: http://review.coreboot.org/631
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
If PCI config cycles use MMIO instead of I/O in the bootblock
code the cycles will go nowhere since the MMIO feature hasn't been
configured yet. This change forces the cycles to use I/O.
Change-Id: I93dec45f7cd6764cef7736c774a4d4e61bf7d7e0
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: http://review.coreboot.org/630
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Extend the Family10 revisions checked byt the printk message.
Change-Id: Ia94daeefb1aabfb128c577b1e0aa52cf63d5cf44
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: http://review.coreboot.org/633
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
No in-tree board using that chipset has it not selected, so move
selection from boards to southbridge.
Change-Id: Ibfb7b294aa5007ac2f767d85e090572f85148bad
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/659
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
|
|
No in-tree board using that chipset has it not selected, so move
selection from boards to southbridge.
Change-Id: I7a7a1919b7a555156b8da21e8db7dd8f682d68e1
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/661
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
|
|
No in-tree board using that chipset has it not selected, so move
selection from boards to southbridge.
Change-Id: Ifba0b65d81af60774f368d151e935ae1cc768336
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/662
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
|
|
No in-tree board using that chipset has it not selected, so move
selection from boards to southbridge.
Change-Id: I9762ef01fc10c453ef643599c1c5dc8ee78081c3
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/663
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
|
|
No in-tree board using that chipset has it not selected, so move
selection from boards to southbridge.
Change-Id: I83105e92d1cc5d2d12aede564a1ab9c5d912ac56
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/664
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
|
|
No in-tree board using that chipset has it not selected, so move
selection from boards to southbridge.
Change-Id: I521deecf58e5d5de303f1ef2f5ff7e965294de18
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/665
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
|
|
No in-tree board using that chipset has it not selected, so move
selection from boards to southbridge. (cimx/sb800 is a "different"
chipset)
Change-Id: If7cf2a141a1f2df60f687c51fbd760aa405c8480
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/666
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
|
|
The current directory is always part of the search path of cpp when
using #include "..."
Change-Id: I74fe39e0c79835e4b9a927afcbeab21040d8ae52
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/648
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Fix issues reported by new lint test.
Change-Id: I077a829cb4a855cbb3b71b6eb5c66b2068be6def
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/646
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
No in-tree amd8111-using board has it not selected, so move
selection from boards to southbridge.
Change-Id: Iabbaa4cd2fd367ed6decec7ef5cdcbae3b264d52
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/654
Reviewed-by: Marc Jones <marcj303@gmail.com>
Tested-by: build bot (Jenkins)
|
|
No in-tree 82801dx-using board has it not selected, so move
selection from boards to southbridge.
Change-Id: I69671cb6411a6cd9c791059ae9546dff3aff702c
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/655
Reviewed-by: Marc Jones <marcj303@gmail.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Change-Id: If924b7eb176e7d3d82fa394929b653b1ced3a743
Signed-off-by: Kerry Sheh <kerry.she@amd.com>
Signed-off-by: Kerry Sheh <shekairui@gmail.com>
Reviewed-on: http://review.coreboot.org/561
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
|
|
without it, you can't boot from PCI devices like scsi controllers
which require an interrupt set. So preconfigure all pci devices.
Change-Id: I2cd781227701e8363d83bd90e0e36994359fc194
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-on: http://review.coreboot.org/603
Tested-by: build bot (Jenkins)
|
|
AGESA and CIMX build changed from commit 2a830d0b,
sb800 and sb900 CIMX dir already traversed in vendorcode Makefile.
Change-Id: I5101b22e140725337bf5074b9170e582c8e3bf40
Signed-off-by: Kerry Sheh <kerry.she@amd.com>
Signed-off-by: Kerry Sheh <shekairui@gmail.com>
Reviewed-on: http://review.coreboot.org/602
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
BIOS needs to set the bit mask which ports are iplemented on the
board. Without setting this option, seabios fails to boot from
SATA.
Change-Id: I21de3fde3a9cff7c590226f70fa549274f36e2a8
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-on: http://review.coreboot.org/601
Tested-by: build bot (Jenkins)
|
|
i3100 misses the magic SATA init sequence, which makes all
requests fail. Captured from the vendor BIOS, which writes
those bits on all configurations.
Change-Id: I293b7d9cd681181311ecaced6d7df9b2706c711f
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-on: http://review.coreboot.org/600
Tested-by: build bot (Jenkins)
|
|
Change-Id: Id34615f0c229d276d72cdf984cf82ea8cc1a85bb
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/523
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
We used to put the id section at -0x10, with some boards overriding
this to avoid collisions with romstraps.
Hardcode the location at -0x80, at the possible expense of some space
(0x70 bytes).
This also makes the section easier to find in a binary image.
At some point, CONFIG_ID_SECTION_OFFSET can be removed, so this option
is moved to src/Kconfig.deprecated_options.
Change-Id: I6ce2d6e94e57717939bda070bfe0c9df80ca2a89
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/549
Tested-by: build bot (Jenkins)
Reviewed-by: Peter Stuge <peter@stuge.se>
|
|
Change-Id: I6b612dbd3eb6e8cc45f1c7abca85732fb64de98c
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-on: http://review.coreboot.org/531
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Tested-by: build bot (Jenkins)
|
|
Change-Id: I6417a92523eea7307d080669fbc4e16ee28c8a6c
Signed-off-by: Jonathan A. Kollasch <jakllsch@kollasch.net>
Reviewed-on: http://review.coreboot.org/524
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Change-Id: Ie3872c57990f9784aafda14f8c7fc842b3a65260
Signed-off-by: Jonathan A. Kollasch <jakllsch@kollasch.net>
Reviewed-on: http://review.coreboot.org/518
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-by: Marc Jones <marcj303@gmail.com>
|
|
Change-Id: I059d5b155cae051f31cc2495f8a47d53e01af808
Signed-off-by: Jonathan A. Kollasch <jakllsch@kollasch.net>
Reviewed-on: http://review.coreboot.org/519
Tested-by: build bot (Jenkins)
Reviewed-by: Peter Stuge <peter@stuge.se>
|
|
Verb data is required for the HDA audio codec in the sb800 southbridge. Verb
data is not required for mainboards that use G-Series HDMI. It is also a setting
the may be boards specific. This fixes issues with Windows audio on Persimmon.
Change-Id: I067506871e92078d122cf79872363d8937d47e50
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: http://review.coreboot.org/490
Tested-by: build bot (Jenkins)
Reviewed-by: Kerry Sheh <shekairui@gmail.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Untested, changes ramstage build for boards:
supermicro/h8qme_fam10
amd/serengeti_cheetah
amd/serengeti_cheetah_fam10
AMD 8132 was not built for any mainboard due to a typo.
AMD Serengeti Cheetah:
Chip 8151 is referenced in devicetree.cb but was not built.
AMD Serengeti Cheetah Family10:
There are indications the board has 8151, but it is not listed
in the devicetree.cb. The 8151 chip is not added in the build.
Change-Id: I03acdfcc3f3440bd32e81a9a696159903bbbcb50
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/471
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
|
|
With this commit the vgainfo is printed and looks like that on the serial console:
vgainfo:
ulBootUpEngineClock:50000
ulBootUpUMAClock:66700
ulBootUpSidePortClock:0
ulMinSidePortClock:0
ulSystemConfig:0
ulBootUpReqDisplayVector:0
ulOtherDisplayMisc:0
ulDDISlot1Config:0
ulDDISlot2Config:0
ucMemoryType:0
ucUMAChannelNumber:1
ucDockingPinBit:0
ucDockingPinPolarity:0
ulDockingPinCFGInfo:0
ulCPUCapInfo: 2
usNumberOfCyclesInPeriod:0
usMaxNBVoltage:0
usMinNBVoltage:0
usBootUpNBVoltage:0
ulHTLinkFreq:20000
usMinHTLinkWidth:8
usMaxHTLinkWidth:8
usUMASyncStartDelay:100
usUMADataReturnTime:300
usLinkStatusZeroTime:600
ulHighVoltageHTLinkFreq:20000
ulLowVoltageHTLinkFreq:20000
usMaxUpStreamHTLinkWidth:8
usMaxDownStreamHTLinkWidth:8
usMinUpStreamHTLinkWidth:8
usMinDownStreamHTLinkWidth:8
Change-Id: I17c2a13ab52a0f78588f812d4f42f45f9a7b7524
Signed-off-by: Denis 'GNUtoo' Carikli <GNUtoo@no-log.org>
Reviewed-on: http://review.coreboot.org/456
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Change-Id: I9f70da76b5ea451f28a1ad9252c5d879fc4fe315
Signed-off-by: Florian Zumbiehl <florz@florz.de>
Reviewed-on: http://review.coreboot.org/387
Tested-by: build bot (Jenkins)
Reviewed-by: Rudolf Marek <r.marek@assembler.cz>
|
|
Change-Id: I70202d81ddd1b0a00eddca4acabc621e5783e805
Signed-off-by: Florian Zumbiehl <florz@florz.de>
Reviewed-on: http://review.coreboot.org/386
Tested-by: build bot (Jenkins)
Reviewed-by: Rudolf Marek <r.marek@assembler.cz>
|
|
Change-Id: I1b5d23cee9f933aa090c9bd09890c7b335567e17
Signed-off-by: Florian Zumbiehl <florz@florz.de>
Reviewed-on: http://review.coreboot.org/388
Tested-by: build bot (Jenkins)
Reviewed-by: Rudolf Marek <r.marek@assembler.cz>
|
|
Change-Id: I830c9a3daf5ac2e1ecd9a3e725a0b98f06509769
Signed-off-by: Florian Zumbiehl <florz@florz.de>
Reviewed-on: http://review.coreboot.org/385
Tested-by: build bot (Jenkins)
Reviewed-by: Rudolf Marek <r.marek@assembler.cz>
|
|
and remove it from mainboard/intel/mtarvon, as this function
is implemented in the southbridge code.
Change-Id: Id3669aaf99b96b4a7a965f4957e5de7c365acaa6
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-on: http://review.coreboot.org/469
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Change-Id: Ia7e3e77235530e952b2e84fdec8373b90fa59b7a
Signed-off-by: Florian Zumbiehl <florz@florz.de>
Reviewed-on: http://review.coreboot.org/437
Tested-by: build bot (Jenkins)
Reviewed-by: Rudolf Marek <r.marek@assembler.cz>
|
|
make code dependent on CONFIG_SOUTHBRIDGE_VIA_K8T800 also be included
for CONFIG_SOUTHBRIDGE_VIA_K8T800_OLD
Change-Id: I9f4624d08de2790fb513a88ed6207e28e7fbc733
Signed-off-by: Florian Zumbiehl <florz@florz.de>
Reviewed-on: http://review.coreboot.org/374
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Change-Id: I2ad82b8059efb09f0593933cb6f53b51b653d494
Signed-off-by: Florian Zumbiehl <florz@florz.de>
Reviewed-on: http://review.coreboot.org/373
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
http://review.coreboot.org/#change,378 introduced a function in k8x8xx.h
move this function to ctrl.c and add a prototype to the header file instead.
Change-Id: I0919ffb2030c53669b95f58b649d4a160f660923
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/429
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
