Age | Commit message (Collapse) | Author |
|
be the
D1F0 bridge without activated I/O and MEM resources, otherwise it will hang
whole PCI bus.
U-boot is also disabling the IO/MEM decode when sizing the BARs, dont know why
does we not.
Second small change just changes a bit which controls the PSTATECTL logic.
Third change deals with the integrated VGA, which needs to be enabled early,
so the VGA_EN is set along the bridges, and PCI K8 resource maps are set
correctly. Finally the CPU accessible framebuffer is now disabled as it is not
needed.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3587 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
programming remains unchanged (tested
on mine desktop) except of reverting the small change introduced by Bari
(gpio/inta setup reg 0x5b). This should go for some board specific file. The
change would broke at least mine board. But seems to be needed for jakllsch.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Bari Ari <bari@onelabs.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3567 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
All devices work, no irq storms. Enjoy.
Signed-off-by: Bari Ari <bari@onelabs.com>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3556 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Bari Ari <bari@onelabs.com>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3369 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
The V-link setup and HT bridge is redone, because VT8237A has it in another
device. So far following combination of chipsets should now work:
K8T890CE + VT8237R
K8M890(CE) + VT8237R
VIA PC1 brige moved to NB code (vt8237r_bridge.c -> k8t890_bridge.c) and
notes about K8M890 support were added.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3183 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
max width of the link and also it will take the frequency of K8 HT
already done coreboot (and checks if t can run on it).
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3169 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
flashes such as SST49LF080A: 1024K x8 (8 Mbit)
Tested on my system, the flash is found and if I use coreboot in second half it
works too.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3148 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
nVidia cards. The enable link should be enough, retrain is done there.
Tested on my system.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3147 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
code is changed.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3052 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
- Use 'static' where appropriate.
- Use 'const' where appropriate.
- Indentation fixes.
- Add comment wrt init code which is only valid for VT8237R.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2974 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Upon incoming SMAF message from CPU (C3 or FID/VID change), the SB will
assert SLP# which is connected to LDTSTOP_L on K8 CPUs. Question is for how
long. Imho for 100us. Which is more than plenty (2us required) I will try
to justify this once I know what bios to set in SB.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2965 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
it to 8X transfer rate (up to 1066 MB/s) similar code placed here would be
needed for VT8237A/S etc. Using VIA recommended values despite they are for
K8T890CF, this is K8T890CE (still dont know what is exactly different).
This patch enables the parity error reporting on V-Link, so it enables NMI
generation for the SERR# errors. The NMI may not be generated, maybe port
61h needs some tuning too.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2958 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
ARRAY_SIZE() can be used on ROMCC-dependent systems. Also adds stdlib.h
to vt8237r_early_smbus.c, so it'll build on those systems.
Signed-off-by: Corey Osgood <corey.osgood@gmail.com>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2949 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2939 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
the Jetway J7F2 patch that should be coming soon, and also moves most
defines into vt8237r.h. I've changed some of the values from u32 to u8,
because that's all they should ever need to be. Also includes
doxygenized comments!
Signed-off-by: Corey Osgood <corey.osgood@gmail.com>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2937 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: <corey.osgood@gmail.com>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2907 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
rodata.pci_driver" warnings are coming from? We were packing those
structures into a read-only segment, but forgot to mark them const.
Despite its size, this is a fairly trivial patch created by a simple
search/replace
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2891 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2883 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
broke and stopped FILO
from being able to boot.
The fix is a simple one line change plus a comment to
src/mainboard/via/epia/auto.c to write to the IDE
configuration register 0x42 . This has always been done here, however
at some point
something broke it.
The same register was also being set correctly in ide_init(), however
for some reason
this does not work. Possibly the register needs to be set before the IDE
peripheral is enabled
or maybe it is a timing issue.
The section of code in ide_init() (
src/southbridge/via/vt8231/vt8231_ide.c ) that does
write to register 0x42 has been commented out as it is superfluous
and I have added a comment to indicate the reason, should someone at a
future date wonder
why.
I have also changed the default COM speed from 19200 to 115200 in
src/mainboard/via/epia/Options.lb
There has been mention before about the EPIA board not being able to use
115200 but I have seen
no such problems with my board.
Signed-off-by: Ben Hewson <ben@hewson-venieri.com>
This patch worked for me and allowed me to boot Debian kernel
2.5.16-4-486 on an epia 800 mhz system. It is able to consistently get
through the initialization and start init now.
However, after that it crashes at various points in the boot process.
Acked-by: Alex Mauer <hawke@hawkesnest.net>
Note from comitter: I am commiting this, although:
1. it's not the exact right way to fix it up, the chip.h for the sb
should change
2. Alex reports problems, which are almost certainly memory issues.
But it is as close as we've gotten. I can't test it.
Ron Minnich
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2633 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
southbridge (with integrated Super-I/O).
Signed-off-by: Corey Osgood <corey_osgood@verizon.net>
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Corey Osgood <corey_osgood@verizon.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2571 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
same format for all CHIP_NAME() entries in LinuxBIOS (Closes #20).
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@linuxbios.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2490 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2408 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
disable agp slot in config.lb
fix error in setting up com1 == should be TTYS0_BAUD
note that the uart8250 struct is a bad design, but so is the
uart8250 code.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2161 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
to fail later than before.
dos2unix'ed the xe7501devkit files, that might have caused some problems
before.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2127 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2091 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2090 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2051 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2038 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2000 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Creator: Li-Ta Lo <ollie@lanl.gov>
More Via EPIA
more via epia stuff, including the trival but fatal bug in auto.c
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1978 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Creator: Li-Ta Lo <ollie@lanl.gov>
emulator update
x96emu update from Paulo
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1954 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Creator: Li-Ta Lo <ollie@lanl.gov>
TLA is really diffcult to use. How am I going to
roll back my last commit ?
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1953 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Creator: Li-Ta Lo <ollie@lanl.gov>
emulator update
Correction to the reduce emulator from Paulo
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1952 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
smbus_read_byte routine updated as per suggestion by rgm
addition reset & wait_until_ready to allow correct reading of first
byte on epia systems.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1807 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
- Move pci_set_method out of hardwaremain.c
- Re-add debugging name field but only include the CONFIG_CHIP_NAME is
enabled. All instances are now wrapped in CHIP_NAME
- Many minor cleanups so most ports build.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1737 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
New Files :-
src/cpu/via/model_centaur/Config.lb
src/cpu/via/model_centaur/model_centaur_init.c
Updated Files :-
src/arch/i386/include/arch/smp/mpspec.h
- make write_smp_table a define for non smp systems
src/cpu/x86/lapic/lapic_cpu_init.c
- change possible typo
src/mainboard/via/epia/Config.lb
src/mainboard/via/epia/Options.lb
src/mainboard/via/epia/auto.c
src/mainboard/via/epia/chip.h
src/mainboard/via/epia/failover.c
- updated after recent code changes
src/northbridge/via/vt8601/chip.h
src/northbridge/via/vt8601/northbridge.c
src/northbridge/via/vt8601/raminit.c
- corrections after recent code changes to allow compiling
src/southbridge/via/vt8231/chip.h
src/southbridge/via/vt8231/vt8231.c
- initial pass to allow compiling after recent code changes.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1726 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
- Rename chip_config chip_operations throughout the tree
- Fix Config.lb on most of the Opteron Ports
- Fix the amd 8000 chipset support for setting the subsystem vendor and device ids
- Add detection of devices that are on the motherboard (i.e. In Config.lb)
- Baby step in getting the resource limit handling correct, Ignore fixed resources
- Only call enable_childrens_resources on devices we know will have children
For some busses like i2c it is non-sense and we don't want it.
- Set the resource limits for pnp devices resources.
- Improve the resource size detection for pnp devices.
- Added a configuration register to amd8111_ide.c so we can enable/disable individual ide channels
- Added a header file to hold the prototype of isa_dma_init
- Fixed most of the superio chips so the should work now, the via superio pci device is the exception.
- The code compiles and runs so it is time for me to go to bed.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1698 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Things are close but not quite there yet.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1681 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1655 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1524 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1515 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1514 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1512 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1451 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1228 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1227 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1224 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
- Support for compiling romcc on non x86 platforms
- new romc options -msse and -mmmx for specifying extra registers to use
- Bug fixes to device the device disable/enable framework and an amd8111 implementation
- Move the link specification to the chip specification instead of the path
- Allow specifying devices with internal bridges.
- Initial via epia support
- Opteron errata fixes
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1200 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1177 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1176 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1174 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1172 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1165 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1163 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Now to fix the ram ...
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1159 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
ron
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1153 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1152 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1150 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1138 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1132 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|