Age | Commit message (Collapse) | Author |
|
Change-Id: I8ef5f1571ad14ead2d4cc0d61b6b7133d7fc8550
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/6293
Tested-by: build bot (Jenkins)
Reviewed-by: Idwer Vollering <vidwer@gmail.com>
|
|
The end of the _PS0 method that is supposed to transition the
XHCI device to D0 state is instead putting it in D3 state.
This triggers a PME_B0 GPE which causes a Notify to the XHCI
ACPI Device in the kernel and that increments the wakeup counter
and causes aborted suspends.
Instead if we just leave the device in D0 where it should be
after executing this function then the PME_B0 is not generated
and the kernel does not see a wakeup on XHCI.
Similarly I changed the _PS3 method to always put the device in
D3 at the end of the method, rather than depending on the state
to be D3 at the start.
Before this change the kernel would see the following sequence
when trying to suspend when the XHCI controller is in D3cold:
kernel: ACPI: Execute Method [\_SB_.PCI0.XHCI._PS0] (Node ffff88017802bf28)
kernel: evmisc-0169 [07] ev_queue_notify_reques: Dispatching Notify on [XHCI] (Device) Value 0x02 (Device Wake) Node ffff88017802bc30
kernel: evmisc-0169 [07] ev_queue_notify_reques: Dispatching Notify on [EHCI] (Device) Value 0x02 (Device Wake) Node ffff88017802b8e8
kernel: evmisc-0169 [07] ev_queue_notify_reques: Dispatching Notify on [HDEF] (Device) Value 0x02 (Device Wake) Node ffff88017802b1b8
kernel: xhci_hcd 0000:00:14.0: power state changed by ACPI to D0
kernel: xhci_hcd 0000:00:14.0: PME# disabled
kernel: xhci_hcd 0000:00:14.0: enabling bus mastering
kernel: xhci_hcd 0000:00:14.0: setting latency timer to 64
kernel: PM: Wakeup pending, aborting suspend
kernel: last active wakeup source: 0000:00:14.0
Now it does not get a notification (due to PME_B0) when going to D0
on the way into suspend. XHCI goes from D3cold to D0 (in order to
be able to read mmio) and then back to D3hot before suspend.
kernel: ACPI: Execute Method [\_SB_.PCI0.XHCI._PS0] (Node ffff88017802bf28)
kernel: xhci_hcd 0000:00:14.0: power state changed by ACPI to D0
kernel: xhci_hcd 0000:00:14.0: PME# disabled
kernel: xhci_hcd 0000:00:14.0: enabling bus mastering
kernel: xhci_hcd 0000:00:14.0: setting latency timer to 64
kernel: ACPI: Execute Method [\_SB_.PCI0.XHCI._S3D] (Node ffff88017802c000)
kernel: xhci_hcd 0000:00:14.0: PME# enabled
kernel: xhci_hcd 0000:00:14.0: System wakeup enabled by ACPI
kernel: ACPI: Execute Method [\_SB_.PCI0.XHCI._PS3] (Node ffff88017802bf50)
kernel: xhci_hcd 0000:00:14.0: power state changed by ACPI to D3hot
Change-Id: Id5cd28eede2b27d97640047feb17349ae4ab79b7
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/65236
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4448
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
The coreboot and ACPI code that clears USB3 PORTSC change status
bits was not properly preserving the state of the PED (port enabled
or disabled) status bit, and it could write 0 back to this field
which would disable the port.
Additionally add back the code that resets disconnected USB3 ports
on the way into suspend (as stated in the BWG) but take care to
clear the PME status bit so we don't immediately wake.
suspend/resume with USB3 devices
1) suspend with no devices, plug in while suspended, then resume
and verify that the devices are detected
2) suspend with USB3 devices inserted, then suspend and resume
and verify that the devices are detected
3) suspend with USB3 devices inserted, then remove the devices
while suspended, resume and ensure they can be detected again
when inserted after resume
Change-Id: Ic7e8d375dfe645cf0dc1f041c3a3d09d0ead1a51
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/65733
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Commit-Queue: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4473
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
The recommended value in docs is D2, but lynxpoint XHCI does not even
support D2 state which causes the kernel to think this device cannot
be used as a wake source:
kernel: xhci_hcd 0000:00:14.0: System wakeup enabled by ACPI
kernel: ACPI: Device does not support D2
kernel: xhci_hcd 0000:00:14.0: System wakeup disabled by ACPI
Additionally this means the kernel will never put the device into D3
state by itself. There is SMI code that will put the device into D3
before suspend so advertising D3 here should be correct.
With this change the kernel will put the controller into D3 on suspend
and back to D0 on resume, including executing the ACPI methods
for _PS0/_PS3 that contain chipset specific workarounds.
In addition add a _PSC method to directly return the D state from the
device registers. With ALL USB devices removed the XHCI controller
goes into D3 state and the kernel can have a hard time determining
the state of the device at boot.
A kernel compiled with CONFIG_ACPI_DEBUG=y and module parameters
acpi.debug_layer=0x7f acpi.debug_level=0x2f can be used to see
what ACPI methods are executed:
kernel: xhci_hcd 0000:00:14.0: System wakeup enabled by ACPI
kernel: ACPI: Execute Method [\_SB_.PCI0.XHCI._PS3] (Node ffff8801000a7f50)
kernel: ACPI: Preparing to enter system sleep state S3
...
kernel: ACPI: Waking up from system sleep state S3
kernel: ACPI: Execute Method [\_SB_.PCI0.XHCI._PS0] (Node ffff8801000a7f28)
kernel: xhci_hcd 0000:00:14.0: power state changed by ACPI to D0
Change-Id: Ic64040eb4dd1947a1e2f0ee253a64be683e0ec70
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
meld with s3d
Change-Id: Ic6789720c4efe661dcb03a4afce8d88115854472
Reviewed-on: https://gerrit.chromium.org/gerrit/63916
Tested-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Commit-Queue: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/4409
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
There are specific programming requirements for the usb3 ports
on all LynxPoint chipsets when transitioning to D0 or D3.
LynxPoint-LP has additional workaround steps needed involving
resetting the disconnected ports when transitioning to D0.
The workarounds are implemented in ACPI code so the controller
can transition properly into D3 at runtime.
Change-Id: I3b428562f48c9cb250b97779a3b2753ed4f81509
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/62632
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4374
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
LynxPoint-LP has a lot of GPEs and the "default" set has been
moved to register 4 starting at bit offset 96. This means
that PME_B0 bit in GPE0_EN/GPE0_STS is now bit 109 in LPT-LP
but still bit 13 in LPT-H.
suspend on falco and wake from usb
4 | 2013-06-19 10:49:17 | ACPI Enter | S3
5 | 2013-06-19 10:49:22 | ACPI Wake | S3
6 | 2013-06-19 10:49:22 | Wake Source | Internal PME | 0
Change-Id: I443cd4d17796888debed70c0bda27ae09accd09b
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/59265
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4253
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
|
|
The ACPI code was defining two EHCI controllers and ignoring
the XHCI controller. This changes the second EHCI controller
to be XHCI instead and changes the wake resource to indicate
S3 and not S4.
cat /proc/acpi/wakeup
Device S-state Status Sysfs node
HDEF S4 *disabled pci:0000:00:1b.0
EHCI S3 *enabled pci:0000:00:1d.0
XHCI S3 *enabled pci:0000:00:14.0
Change-Id: If28775e6ef8608c22c85ca91d91d1f598ec7755d
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/56263
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4181
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
The Haswell parts use a PCH code named Lynx Point (Series 8). Therefore,
the southbridge support is included as well. The basis for this code is
the Sandybridge code. Management Engine, IRQ routing, and ACPI still requires
more attention, but this is a good starting point.
This code partially gets up through the romstage just before training
memory on a Haswell reference board.
Change-Id: If572d6c21ca051b486b82a924ca0ffe05c4d0ad4
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2616
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|