Age | Commit message (Collapse) | Author |
|
This is an LPT-LP specific method that will enable a specific
GPIO as an ACPI SCI wake source.
It can be used by a device _DSW method to enable a pin that is
otherwise not configured to generate SCI at runtime.
It will set:
- GPIO owner to ACPI
- GPIO route to SCI
- GPIO config to GPIO, Input, Inverted
Also clean up and remove ACPI field definitions that are unused
and/or incorrect.
Change-Id: I14acc2de50e6200f61c2898a7bd1252400e0f0be
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/56621
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/4189
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
In order to probe the gpio-lynxpoint kernel driver the
LP GPIO controller needs to be exposed as a specific
ACPI device.
This also allows the resources to be exposed to the OS via
this device instead of the catch-all LPC device.
Ensure the driver loads at boot:
gpiochip_find_base: found new base at 162
gpiochip_add: registered GPIOs 162 to 255 on device: INT33C7:00
Also ensure the driver is visible in sysfs:
$ cat /sys/devices/platform/INT33C7:00/gpio/gpiochip162/label
INT33C7:00
Change-Id: I9f79c008f88da9b67ed1cdfdb9d3a581ce8f05ff
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/50215
Reviewed-on: http://review.coreboot.org/4158
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
The kernel ACPI was not happy with the Add inside a
ResourceTemplate (or perhaps within the IO declaration)
Instead make a buffer of IO reservations and turn _CRS
into a method that updates the buffer depending on the
chipset type.
This adds an \ISLP() method that checks the chipset LPC
device ID to see if it is -LP or -H.
It also increases the PM base reservation to 256 bytes
and moves both GPIO and PM base to above 0x1000 on -LP
chipsets.
Change-Id: I747b658588a4d8ed15a0134009a7c0d74b3916ba
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/2815
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
The low power variant of the chipset introduces a completely
new interface to the GPIOs.
This is a 1KB region and so needs to be moved as well so it does
not conflict with other IO regions.
Also expose the gpio_get functions to ramstage and move the
prototypes to pch.h so they can be used for both GPIO interfaces.
Change-Id: I20bc18669525af16de8cdf99f0ccfa9612be63ad
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/2648
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
|
|
The Haswell parts use a PCH code named Lynx Point (Series 8). Therefore,
the southbridge support is included as well. The basis for this code is
the Sandybridge code. Management Engine, IRQ routing, and ACPI still requires
more attention, but this is a good starting point.
This code partially gets up through the romstage just before training
memory on a Haswell reference board.
Change-Id: If572d6c21ca051b486b82a924ca0ffe05c4d0ad4
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2616
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|