Age | Commit message (Collapse) | Author |
|
Signed-off-by: Myles Watson <mylesgw@gmail.com>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3943 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Reorder HDA (HD Audio) init:
The reordering was based on what order things happen in the BIOS
Developers guide, RPR, and SATA driver. I fixed the order of the devices
that didn't matter to clean up the change log.
1. Enable the Chip
2. Setup the SMBus registers
3. Setup the Device Registers
4. Look for Codec
5. Init Codec
The codec init was changed to match the description in the RRG pg 235.
Mem Reg: Base + 08h Bit 0. There were unneeded things happening.
Added 1ms delay to match the BKDG while waiting for BAR+0xe to set its
bits.
Signed-off-by: Dan Lykowski <lykowdk@gmail.com>
Tested on AMD DBM690T and AMD Pistachio by Maggie Li. Works.
Tested on Asus M2A-VM by Carl-Daniel Hailfinger. Improves the situation,
but some warnings remain.
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3930 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Maggie Li <maggie.li@amd.com>
Reviewed-by: Zheng Bao <Zheng.bao@amd.com>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3891 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
SATA port status kept returning 0x1: BAR5+po+28h
1h = Device presence detected but Phy communication not established
This patch adds logic to force 1.5g if the drive fails to communicate at 3.0g.
Signed-off-by: Dan Lykowski <lykowdk@gmail.com>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3864 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
is no longer 0xA0 or 0xB0. It simply assumes that will never happen.
My 500 GB Seagate Barracuda ST3500820AS triggers that corner case on the
first init after poweron.
The current code hangs forever with my drive. Fix this by rerunning the
init sequence after SATA_BAR0+6 is no longer 0xA0 or 0xB0.
Add support for SATA port 2-4 (Primary Slave, Secondary Master,
Secondary Slave).
If only the 2nd SATA port is connected and the hardware acts strangely
(contrary to documentation), it will print the error message below and
continue anyway. The official AMD asm code behaves the same way.
SATA port 0 status = 0
No Primary Master SATA drive on Slot0
SATA port 1 status = 23
0x6=7f, 0x7=7f
drive no longer selected after 0 ms, retrying init
[8 repetitions]
0x6=7f, 0x7=7f
drive no longer selected after 0 ms, retrying init
Primary Slave device is not ready after 10 tries
Activate and improve debug messages for SPEW log level.
Fix some comments.
New log messages look like this:
PCI: 00:12.0 init
sata_bar0=3020
sata_bar1=3060
sata_bar2=3030
sata_bar3=3070
sata_bar4=3000
sata_bar5=fc309000
SATA port 0 status = 23
0x6=a0, 0x7=80
drive detection not yet completed, waiting...
0x6=a0, 0x7=80
drive detection not yet completed, waiting...
[... 281 repetitions ...]
0x6=0, 0x7=50
drive no longer selected after 2820 ms, retrying init
drive detection done after 0 ms
Primary Master device is ready after 2 tries
SATA port 1 status = 23
drive detection done after 0 ms
Primary Slave device is ready after 1 tries
SATA port 2 status = 0
No Secondary Master SATA drive on Slot2
SATA port 3 status = 0
No Secondary Slave SATA drive on Slot3
With this patch, my Asus M2A-VM boots into Linux without problems.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Zheng Bao <zheng.bao@amd.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3845 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
The RS690 chipset has a problem where it will not work with 1 GHz HT
speed unless NB_CFG_Q_F1000_800 bit 0 is set.
Tested, works on my Asus M2A-VM with an 1 GHz HT capable processor.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Bao, Zheng says:
As a matter of fact, both 600Mhz and 1Ghz have their own specific
setting.
This patch has been tested on dbm690t which HT link works on 800Mhz.
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3839 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
the SB600 code.
Signed-off-by: Maggie Li <Maggie.li@amd.com>
Reviewed-by: Zheng bao <Zheng.bao@amd.com>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3837 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
except get_nodes.
Signed-off-by: Myles Watson <mylesgw@gmail.com>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3818 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
The device ID of 690G is 0x791E, while the ID of 690M and 690T is 0x791F
This fixes booting on 690G.
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3816 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
mainboard specific code. (And add a hook to allow other mainboards do
a similar thing if required)
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Ronald G Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3812 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
document verification against the data sheets.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Maggie Li <maggie.li@amd.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3811 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Joe Bao <zheng.bao@amd.com>
Reviewed-by: Maggie Li <maggie.li@amd.com>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3786 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Joe Bao <zheng.bao@amd.com>
Reviewed-by: Maggie Li <maggie.li@amd.com>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3785 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Myles Watson <mylesgw@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3752 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Also, use more readable #defines instead of hardcoded config ports for
PM/PM2 related functions, and simplify them a bit.
Build-tested with the AMD dbm690t target.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Marc Jones <marc.jones@amd.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3680 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Jordan Crouse <jordan.crouse@amd.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3678 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Build-tested with the AMD dbm690t board.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Marc Jones <marc.jones@amd.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3655 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
cleanup. (trivial)
Signed-off-by: Marc Jones <marcj.jones@amd.com>
Acked-by: Marc Jones <marcj.jones@amd.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3643 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
We shouldn't assume the presence of a working HDA codec, so put in
a reasonable timeout of 50usecs (timeout value borrowed from the kernel).
This makes SimNow work, since apparently though the codec is
present in Simnow, it is non functional.
Signed-off-by: Jordan Crouse <jordan.crouse@amd.com>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3640 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
got checked into v2. This should get us back to where we were. (trivial)
Signed-off-by: Marc Jones <marc.jones@amd.com>
Acked-by: Marc Jones <marc.jones@amd.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3636 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
certainly won't build -- that comes later. I am hoping to get some
eyeballs on it for simple errors.
rs690 is next.
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3630 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
code to use it. That makes the code more readable and also less
error-prone.
Abuild tested.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3624 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Most of the functions in SB600 are enabled except power management.
Signed-off-by: Michael Xie <Michael.Xie@amd.com>
Reviewed-by: Marc Jones <marc.jones@amd.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3589 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
All the PCIe slots are enabled in this patch except power management.
Signed-off-by: Michael Xie <Michael.Xie@amd.com>
Reviewed-by: Marc Jones <marc.jones@amd.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3588 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
patch uses byte pointer and the MMIO read and write functions.
Signed-off-by: Marc Jones <marc.jones@amd.com>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3421 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
doing a
pci_write_config8.
Signed-off-by: Marc Jones <marc.jones@amd.com>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3282 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
You can see this by executing commands like this:
grep -r pci_assign_irqs coreboot/src/*
This basically AMD/LX based boards: pcengines/alix1c,
digitallogic/msm800sev, artecgroup/dbe61, amd/norwich, amd/db800.
Also for AMD/GX1 based boards need a patch
[http://www.pengutronix.de/software/ptxdist/temporary-src/references/geode-5530.patch]
for the right IRQ setup.
AMD/GX1 based boards is: advantech/pcm-5820, asi/mb_5blmp, axus/tc320,
bcom/winnet100, eaglelion/5bcm, iei/nova4899r, iei/juki-511p.
I have two ideas.
1. Delete duplicate code from AMD/LX based boards.
2. Add IRQ routing for AMD/GX1 boards in coreboot.
The pirq.patch for IRQ routing logically consist from of two parts:
First part of pirq.patch independent from type chipsets and assign IRQ for
ever PCI device. It part based on AMD/LX write_pirq_routing_table() function.
Second part of pirq.patch depends of type chipset and set PIRQx lines
in interrupt router. This part supports only CS5530/5536 interrupt routers.
IRQ routing functionality is included through PIRQ_ROUTE in Config.lb.
Tested on iei/juki-511p(cs5530a), iei/pcisa-lx(cs5536) and also on
TeleVideo TC7020, see
http://www.coreboot.org/pipermail/coreboot/2007-December/027973.html.
Signed-off-by: Nikolay Petukhov <nikolay.petukhov@gmail.com>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3196 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Due to the automatic nature of this update, I am self-acking. It worked in
abuild.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3053 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
code is changed.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3052 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Check that the SMBus controller is found and stop on an error.
Clean up and add additional path through the 8111 reset functions.
Signed-off-by: Marc Jones <marc.jones@amd.com>
Reviewed-by: Jordan Crouse <jordan.crouse@amd.com>
Acked-by: Myles Watson <myles@pel.cs.byu.edu>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3015 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
rodata.pci_driver" warnings are coming from? We were packing those
structures into a read-only segment, but forgot to mark them const.
Despite its size, this is a fairly trivial patch created by a simple
search/replace
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2891 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Painting the splash graphic is now ifdef'ed.
Signed-off-by: Juergen Beisert <juergen127@kreuzholzen.de>
Acked-by: Peter Stuge <peter@stuge.se>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2836 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
to set up one of five screen resolutions (sorry no autodetection at runtime,
resolution is selected at buildtime) and displays a graphic in the right
bottom corner (splash screen).
Signed-off-by: Juergen Beisert <juergen127@kreuzholzen.de>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2827 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
mostly undocumented, had a broken coding style, contained lots of dead
code and had several other problems, e.g. it enabled write access to the
ROM (why?), it unconditionally enabled primary/secondary IDE (which should
have a config option) and that even _twice_ (which is um... wrong).
The new code
- has 'ide0_enable' and 'ide1_enable' config options (which actually
work) to enable/disable the primary/secondary IDE interface in
Config.lb.
- Does _not_ enable write access to the ROM (or is there some good
reason to do that? If so, it should at least have a config option).
- Contains a bit more documentation.
- Uses readable (and documented) #defines instead of hardcoded magic values.
- aaand... it actually compiles ;-) Yep, that's right. The previous code
wouldn't even build, as it hadn't been fully ported from v1 (still used
v1 functions which are simply not available in v2).
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2775 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Marc Jones <marc.jones@amd.com>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2726 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
return that skipped the disable code. This patch removes the return and
fixes the UART disable code.
The problem was that the disable code was ORing bits into the Legacy_IO
MSR causing issues with the LPC SIOs init code that would manifest as a
hang because the IO would not be decoded correctly. ANDing to clear the
bits fixes the issue.
Signed-off-by: Marc Jones <marc.jones@amd.com>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2706 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
the new src/southbridge/amd/cs5536 code completely replaces it.
The Artecgroup dbe61 board currently uses it, but that is broken anyway
at the moment. A fix to use the new CS5536 code for it is being worked on.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2697 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Marc Jones <marc.jones@amd.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2687 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
setup as the host on USB port4. In client mode the headers remain
available. Also fixes an outb to 0x80 to use the post_code() function.
Signed-off-by: Marc Jones <marc.jones@amd.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2660 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Marc Jones <marc.jones@amd.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2658 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Marc Jones <marc.jones@amd.com>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2656 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Jordan Crouse <jordan.crouse@amd.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2651 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Jordan Crouse <jordan.crouse@amd.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2647 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
-This line, and those below, will be ignored--
M cs5536.c
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2637 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
AMD GX and LX processors. This aguments the previous code, which was
very specific to the OLPC platform with general purpose support and
better integration with the VSA and CPUs.
Signed-off-by: Marc Jones <marc.jones@amd.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2631 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
same format for all CHIP_NAME() entries in LinuxBIOS (Closes #20).
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@linuxbios.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2490 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2435 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Ronald G. Minnich
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2430 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2425 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
cs5536, but I don't want to mess up the OLPC, and we really need the lx
support NOW.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2421 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
signed-off-by: Jordan Crouse
Signed-off-by: Ronald G. Minnich
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2410 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
This one actualy works. You cannot just go mucking about with stuff that the VSA
has under its thumb. Bad Things happen. This does it the VSA way.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2392 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
This should make the USB P4 work as a USB host
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2389 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2388 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
USB P4 is disabled by default and we need to setup the mux bits proper
to make it work. This is the frame work for that. All thats needed
is the right address values
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2387 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2377 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
UART. If the upper banks are enabled, then the Linux 8250 driver knows
how to set baud speeds greater then 115200. This was prompted by David
Woodhouse.
Jordan"
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2348 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2346 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
disabled.
cs5536: add new entires for SB control etc.
cs5536.c: chip_enabled function moved to chip_init, so it only gets run
once.
IRQ setup improved
gx2def.h: new defines added
vr.h: new file, with new def's for virtual register control.
mainboard config.lb: new entries added for nb and sb control.
chipsetinit.c: new controls added -- I forget all the details :-)
grphinit.c: new function added
northbridge.c: new IRQ control added. FlashChipSetup added, controlled
by chip info setupflash struct member. Currently, if enabled, this hangs
OLPC in linux PCI scan.
chip.h: new struct members added for unwanted device enable, flash setup
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2345 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2334 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
manage them. Make pci_level_irq global. Add value settings for OLPC
rev_a board. Comment out no-longer-needed code in olpc mainboard.c
-- it is replaced by the settings in Config.lb, and the support
in cs5536.c
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2328 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
add support for conditional enable of uarta interrupt.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2324 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2316 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2306 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2299 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2298 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2297 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
We lost a few things, but this is still worth it.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2287 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2284 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2281 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2280 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2277 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2276 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2272 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2269 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2266 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2265 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2263 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2262 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2261 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2253 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2251 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2246 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
try to fix 0x10000026
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2235 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2232 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2227 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2209 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
other fixes for gx2 ram init.
support for sharplfg00l04 -- not working yet.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2197 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
removed some messages
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2194 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
still get garbage reading smbus.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2192 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2190 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2168 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2166 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
This is just a skeleton, basically, and will most likely not even
compile yet.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2164 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2157 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
https://openbios.org/roundup/linuxbios/issue41
Lord have mercy upon us.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2118 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
https://openbios.org/roundup/linuxbios/issue24
- fix up for via epia-m
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2110 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2107 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
- Fixed abuild.sh to use larger size for ROM_IMAGE_SIZE.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2079 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2066 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|