aboutsummaryrefslogtreecommitdiff
path: root/src/southbridge/amd
AgeCommit message (Collapse)Author
2010-02-07newconfig is no more.Patrick Georgi
Signed-off-by: Patrick Georgi <patrick.georgi@coresystems.de> Acked-by: Ronald G. Minnich <rminnich@gmail.com> git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5089 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
2010-02-03The UART2 on the AMD cs5536 is incorrectly configured in two places.Stefan Reinauer
GPIO lines 4 and 3 are swapped and also incorrectly put in IR mode receive (compound fault). Signed-off-by: Stefan Reinauer <stepan@coresystems.de> Acked-by: Edwin Beasant <edwin_beasant@virtensys.com> git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5074 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
2010-01-27reformat Kconfig file, too.Patrick Georgi
Signed-off-by: Patrick Georgi <patrick.georgi@coresystems.de> Acked-by: Patrick Georgi <patrick.georgi@coresystems.de> git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5060 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
2010-01-27Add the MSR writes that are needed to provide VGA legacy routing for the ↵Edwin Beasant
Geode LX Add appropriate Kconfig defines to provide 8mb of VGA ram allocation Add the Kconfig defines to cover TSC calibration from TIMER2 and UDELAY setup Two small warning removals about excessive prototyping. Signed-off-by: Edwin Beasant <edwin_beasant@virtensys.com> Acked-by: Ronald G. Minnich <rminnich@gmail.com> git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5059 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
2010-01-18Move all IOAPIC selection to southbridges, and remove themPatrick Georgi
from mainboards. Some adaptations were necessary after the IOAPIC cleanup, so this should fix the build. Fix intel/d945gclf build, which was missing some ACPI component. Signed-off-by: Patrick Georgi <patrick.georgi@coresystems.de> Acked-by: Stefan Reinauer <stepan@coresystems.de> git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5039 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
2010-01-16coreboot has 13 instances of IOAPIC setup distributed across a lotStefan Reinauer
of components. This patch is a rewrite of the generic IOAPIC setup code. Additionally it drops the other 12 instances of IOAPIC setup code and makes the components use the generic code. Signed-off-by: Stefan Reinauer <stepan@coresystems.de> Acked-by: Ronald G. Minnich <rminnich@gmail.com> git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5023 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
2010-01-16coreboot used to have two different "APIs" for memory accesses:Stefan Reinauer
read32(unsigned long addr) vs readl(void *addr) and write32(unsigned long addr, uint32_t value) vs writel(uint32_t value, void *addr) read32 was only available in __PRE_RAM__ stage, while readl was used in stage2. Some unclean implementations then made readl available to __PRE_RAM__ too which results in really messy includes and code. This patch fixes all code to use the read32/write32 variant, so that we can remove readl/writel in another patch. Signed-off-by: Stefan Reinauer <stepan@coresystems.de> Acked-by: Ronald G. Minnich <rminnich@gmail.com> git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5022 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
2009-12-31romcc:Patrick Georgi
- Set __PRE_RAM__ define per default - Properly handle ignored (#ifdef'd out) #include lines amd/serengeti_cheetah_fam10: - write ACPI files to $(obj) instead of the top dir (alias $(CURDIR)) tinybootblock: - provide a way to define code that should be added to the bootblock, to map the entire ROM for use by CBFS amd/model_fxx, amd/model_10xxx: - add CONFIG_SSE walkcbfs.S: - eliminate the use of two registers, to make space for romcc to wiggle amd/serengeti_cheetah_fam10: - use the enable_rom framework. not entirely functional yet Boot-tested on emulation/qemu-x86 Build-tested on amd/serengeti_cheetah_fam10 amd/serengeti_cheetah_fam10 fails in amdht/ somewhere, but builds Signed-off-by: Patrick Georgi <patrick.georgi@coresystems.de> Acked-by: Ronald G. Minnich <rminnich@gmail.com> git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4994 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
2009-11-06Drop all pre-CBFS rom_address entries in Config.lb/devicetree.cb.Uwe Hermann
Since we have CBFS setting rom_address in board files is no longer necessary. Also, drop vga_rom_address from RS690 completely, it was never used in the code. Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de> Acked-by: Myles Watson <mylesgw@gmail.com> git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4923 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
2009-11-06Split the two usages of __ROMCC__:Myles Watson
__ROMCC__ now means "Don't use prototypes, since romcc doesn't support them." __PRE_RAM__ means "Use simpler versions of functions, and no device tree." There are probably some places where both are tested, but only one is needed. Signed-off-by: Myles Watson <mylesgw@gmail.com> Acked-by: Peter Stuge <peter@stuge.se> git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4921 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
2009-10-16Add CONFIG_VGA_ROM_RUN to dbm690t and pistachio, otherwise theZheng Bao
VGA ROM can not run. After make, run > ./cbfs/cbfstool ./coreboot.rom add ../vga_bios.rom pci1002,791f.rom optionrom to make the final image with vga bios. The macro vga_rom_address is out-of-date when CBFS starts play its role. it also should be eliminated from rs690/chip.h as below. But it will cause building error on other board, which I cant make test on. ## Index: src/southbridge/amd/rs690/chip.h ## =================================================================== ## --- src/southbridge/amd/rs690/chip.h (revision 4782) ## +++ src/southbridge/amd/rs690/chip.h (working copy) ## @@ -23,7 +23,6 @@ ## /* Member variables are defined in Config.lb. */ ## struct southbridge_amd_rs690_config ## { ## - u32 vga_rom_address; /* The location that the VGA rom has been appened. */ ## u8 gpp_configuration; /* The configuration of General Purpose Port, A/B/C/D/E. */ ## u8 port_enable; /* Which port is enabled? GFX(2,3), GPP(4,5,6,7) */ ## u8 gfx_dev2_dev3; /* for GFX Core initialization REFCLK_SEL */ ## Don't apply above patch about rs690/chip.h before every board has been fixed. Signed-off-by: Zheng Bao <zheng.bao@amd.com> Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net> git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4783 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
2009-10-15Add CONFIG_GENERATE_* for tables so that the user can select which tables notMyles Watson
to build, but by default all the tables that are available are built. Make PIRQ table build for qemu. Signed-off-by: Myles Watson <mylesgw@gmail.com> Acked-by: Peter Stuge <peter@stuge.se> git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4778 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
2009-10-14delete white trailing spaces. It is done by the perl command.Zheng Bao
sh> perl -pi -e 's/[[:blank:]]+$//' $files Trivial. Signed-off-by: Zheng Bao <zheng.bao@amd.com> Acked-by: Zheng Bao <zheng.bao@amd.com> git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4772 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
2009-10-13This patch support for the Technexion Tim-5690 mainboard.Libra Li
It's an embedded AMD RS690/SB600 mainboard. http://www.technexion.com/index.php/tim-5690 Myles added Kconfig support. Signed-off-by: Libra Li <libra.li@technexion.com> Signed-off-by: Myles Watson <mylesgw@gmail.com> Acked-by: Stefan Reinauer <stepan@coresystems.de> git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4765 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
2009-10-09Remove default n statements to simplify .config and ldoptions files.Myles Watson
Signed-off-by: Myles Watson <mylesgw@gmail.com> Acked-by: Patrick Georgi <patrick.georgi@coresystems.de> git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4753 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
2009-10-08Fix CS5535 build for kconfig, more kconfig boards (lippert, artec)Patrick Georgi
Signed-off-by: Patrick Georgi <patrick.georgi@coresystems.de> Acked-by: Peter Stuge <peter@stuge.se> git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4748 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
2009-10-07Enable full ROM access on AMD CS5530(A) (needed for CBFS).Uwe Hermann
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de> Acked-by: Patrick Georgi <patrick.georgi@coresystems.de> git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4731 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
2009-10-04Add initial kconfig support for all AMD GX1 boards.Uwe Hermann
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de> Acked-by: Ronald G. Minnich <rminnich@gmail.com> git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4719 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
2009-09-29Remove some warnings.Myles Watson
Signed-off-by: Myles Watson <mylesgw@gmail.com> Acked-by: Stefan Reinauer <stepan@coresystems.de> git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4686 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
2009-09-25some progress on kconfig:Patrick Georgi
- northbridges are done - southbridges are done - Intel CPUs are done, with a design that the board only has to specify the socket it has, and the CPUs are pulled in automatically. There is some more cleanup possible in that area, but I'll do that later - a couple more mainboards compile: - intel/eagleheights - intel/jarrell - intel/mtarvon - intel/truxton - intel/xe7501devkit - sunw/ultra40 - supermicro/h8dme - tyan/s2850 - tyan/s2875 - via/epia - via/epia-cn - via/epia-m - via/epia-m700 - via/epia-n - via/pc2500e (PPC not considered, probably overlooked something) All of them only _build_, but some options are probably completely wrong. To be fixed later Signed-off-by: Patrick Georgi <patrick.georgi@coresystems.de> Acked-by: Ronald G. Minnich <rminnich@gmail.com> git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4673 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
2009-09-22src/Kconfig: Remove HT-specific options.Myles Watson
src/cpu/amd/socket_F/Kconfig: Remove second occurrence of CPU_SOCKET_TYPE. src/mainboard/amd/serengeti_cheetah/Kconfig: Add HT_CHAIN_UNITID_BASE here, since it is board specific. src/mainboard/tyan/s289X/Kconfig: Fix typo and change APIC_ID_OFFSET to match old config. src/devices/Kconfig: Change default value of *_PLUGIN_SUPPORT to match old config. src/southbridge/amd/amd8131/Makefile.inc: Remove check since it was a typo, and the correct variable is checked in the parent directory. src/Makefile:Use devicetree.cb instead of Config.lb to generate static.c. Signed-off-by: Myles Watson <mylesgw@gmail.com> Acked-by: Ronald G. Minnich <rminnich@gmail.com> git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4657 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
2009-08-29This is the final set of changes to allow rumba to build. Rumba is notRonald G. Minnich
tested. I also addressed questions raised by Uwe: TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 UDELAY_TSC Are now defined as booleans in src/cpu/x86/Kconfig and can be selected in the mainboard Kconfig. The remaining question of Uwe's is a deeper problem: --- We'll have to check if this works. From a quick glance the Rumba does not have the mmx related lines (which _are_ in Makefile.romccboard.inc, though): crt0-y += ../../../../src/cpu/x86/fpu/enable_fpu.inc crt0-y += ../../../../src/cpu/x86/mmx/enable_mmx.inc crt0-y += auto.inc crt0-y += ../../../../src/cpu/x86/mmx/disable_mmx.inc --- We're going to need a whole variant of this standard mainboard OR we're going to have to make (some) of the unconditional includes above conditional. Signed-off-by: Ronald G. Minnich <rminnich@gmail.com> Acked-by: Myles Watson <mylesgw@gmail.com> git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4618 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
2009-08-28This is the beginning of support for Geode and Kconfig in v2. Ronald G. Minnich
It also brings in the vsm from v3, which was a much cleaner cut. Over time, I hope to bring all the code back from v3. I have some rumbas at home and want to use them. I have a patch which comes in next that makes the rumba build. Note that I am holding the src/*/amd/Kconfig patch until these get merged. These have no impact on the current system. Note that this is not complete but I want to fill in the blanks bit by bit. Signed-off-by: Ronald G. Minnich <rminnich@gmail.com> Acked-by: Myles Watson <mylesgw@gmail.com> git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4611 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
2009-08-27Added support for the AMD RS690 and SB600 southbridges in KconfigCristi Măgherușan
Signed-off-by: Cristi Măgherușan <cristi.magherusan@net.utcluj.ro> Acked-by: Stefan Reinauer <stepan@coresystems.de> Acked-by: Ronald G. Minnich <rminnich@gmail.com> git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4601 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
2009-08-27The new resource allocator helped me find a bug in SB600 diagnostics.Carl-Daniel Hailfinger
The SB600 SATA code printed that two BARs had the same address because it didn't mask the correct number of bits in the BAR. Functionality was not affected, but the debug output was incorrect. Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net> Acked-by: Zheng Bao <zheng.bao@amd.com> git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4591 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
2009-08-26Remove a couple of CONFIG_ prefixes that shouldn't have happened.Patrick Georgi
Signed-off-by: Patrick Georgi <patrick.georgi@coresystems.de> Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net> git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4588 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
2009-08-26Enable Direct TMDS for the RS690, which allows to display on HDMI and DVILibra Li
monitors. Signed-off-by: Libra Li <libra.li@technexion.com> Acked-by: Marc Jones <marcj303@gmail.com> git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4585 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
2009-08-25Various Kconfig and Makefile.inc fixes and cosmetics.Uwe Hermann
- Whitespace fixes, remove trailing whitespace, use TABs for identation (except in Kconfig "help" lines, which start with one TAB and two spaces as per Linux kernel style) - Kconfig: Standardize on 'bool' (not 'boolean'). - s/lar/cbfs/ in one Kconfig help string. - Reword various Kconfig menu entries for a more usable and consistent menu. - Fix incorrect comment of NO_RUN in devices/Kconfig. - superio/serverengines/Kconfig: Incorrect config name. - superio/Makefile.inc: s/serverengine/serverengines/. - superio/intel/Kconfig: s/SUPERIO_FINTEK_I3100/SUPERIO_INTEL_I3100/. - mainboard/via/vt8454c/Kconfig: Fix copy-paste error in help string. - mainboard/via/epia-n/Kconfig: Fix "bool" menu text. - console/Kconfig: Don't mention defaults in the menu string, kconfig already displays them anyway. - Kill "Drivers" menu for now, it only confuses users as long as it's emtpy. Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de> Acked-by: Uwe Hermann <uwe@hermann-uwe.de> git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4567 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
2009-08-12This now builds. Ronald G. Minnich
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com> Acked-by: Ronald G. Minnich <rminnich@gmail.com> git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4537 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
2009-08-12Missing files from last patch.Ronald G. Minnich
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com> Acked-by: Ronald G. Minnich <rminnich@gmail.com> git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4535 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
2009-08-12Kconfig!Patrick Georgi
Works on Kontron, qemu, and serengeti. Signed-off-by: Patrick Georgi <patrick.georgi@coresystems.de> tested on abuild only. Acked-by: Ronald G. Minnich <rminnich@gmail.com> git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4534 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
2009-07-14trivial fixes to function declarations (and build system test)Stefan Reinauer
Signed-off-by: Stefan Reinauer <stepan@coresystems.de> Acked-by: Stefan Reinauer <stepan@coresystems.de> git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4425 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
2009-07-10This seems to be a more official, common, simple way to check if the CPU is ↵Zheng Bao
dual core or single core. Signed-off-by: Zheng Bao <zheng.bao@amd.com> Acked-by: Ronald G. Minnich <rminnich@gmail.com> git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4415 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
2009-07-02Move the v3 resource allocator to v2.Myles Watson
Major changes: 1. Separate resource allocation into: A. Read Resources B. Avoid fixed resources (constrain limits) C. Allocate resources D. Set resources Usage notes: Resources which have IORESOURCE_FIXED set in the flags constrain the placement of other resources. All fixed resources will end up outside (above or below) the allocated resources. Domains usually start with base = 0 and limit = 2^address_bits - 1. I've added an IOAPIC to all platforms so that the old limit of 0xfec00000 is still there for resources. Some platforms may want to change that, but I didn't want to break anyone's board. Resources are allocated in a single block for memory and another for I/O. Currently the resource allocator doesn't support holes. Signed-off-by: Myles Watson <mylesgw@gmail.com> Acked-by: Ronald G. Minnich <rminnich@gmail.com> Acked-by: Patrick Georgi <patrick.georgi@coresystems.de> git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4394 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
2009-06-30This patch unifies the use of config options in v2 to all start with CONFIG_Stefan Reinauer
It's basically done with the following script and some manual fixup: VARS=`grep ^define src/config/Options.lb | cut -f2 -d\ | grep -v ^CONFIG | grep -v ^COREBOOT |grep -v ^CC` for VAR in $VARS; do find . -name .svn -prune -o -type f -exec perl -pi -e "s/(^|[^0-9a-zA-Z_]+)$VAR($|[^0-9a-zA-Z_]+)/\1CONFIG_$VAR\2/g" {} \; done Signed-off-by: Stefan Reinauer <stepan@coresystems.de> Acked-by: Ronald G. Minnich <rminnich@gmail.com> git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4381 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
2009-06-05After I modify the pci_ext_read_config32 and pci_ext_read_config32, the step 6aZheng Bao
starts to play its role. Then the system hangs at HDA init. I dont know what the VC1 is. The RPR says "Optional Features (only needed if CMOS option is enabled)" in 5.10.2. Before I know what it is, I think it is better to skip it. Tested on dbm690t. Add comment from Rudolf, " VC is virtual channel. Its used for isochronous transfer of data to sound card. The virtual channel guarantee "on time" delivery. In other words it sets up a channel for data to sound card, which means that that arrivs in time and there will be no interuptions in audio stream. http://www.microsoft.com/whdc/connect/pci/wlp_interrupt.mspx " Signed-off-by: Zheng Bao <zheng.bao@amd.com> Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net> git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4339 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
2009-06-04This patch is about some noticable bugs which was made by no reason.Zheng Bao
1. In rs690_cmn.c, mask the lower 4 bits of the BAR3. No doubt, right? 2. In rs690_pcie.c, (1) Obviously, the mask should be 0xF, and bit 19 should be set to 1 (in comment). In rpr 5.10.2, step 2, step 2.1 & step 2.6 (2) The dynamic buffer allocation is enabled by setting bit 11 of PCIEIND: 0x20, instead of PCIEIND_P: 0x20. In rpr 5.10.2, step 5. Dynamic Slave CPL Buffer Allocation Signed-off-by: Zheng Bao <zheng.bao@amd.com> Acked-by: Ronald G. Minnich <rminnich@gmail.com> git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4336 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
2009-06-03Revert "CMOS: Add set_option and rework get_option."Luc Verhaegen
This reverts commit eb7bb49eb5b48c39baf7a256b7c74e23e3da5660. Stepan pointed out that "s" means string, which makes the following statement in this commit message invalid: "Since we either have reserved space (which we shouldn't do anything with in these two functions), an enum or a hexadecimal value, unsigned int seemed like the way to go." Signed-off-by: Luc Verhaegen <libv@skynet.be> Acked-by: Luc Verhaegen <libv@skynet.be> git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4335 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
2009-06-03CMOS: Add set_option and rework get_option.Luc Verhaegen
To ease some of my debugging pain on the unichrome, i decided i needed to move FB size selection into cmos, so i could test a size and then reset it to the default after loading this value so that the next reboot uses the (working) default again. This meant implementing set_option in parallel to get_option. get_option was then found to have inversed argument ordering (like outb) and passing char * and then depending on the cmos layout length, which made me feel quite uncomfortable. Since we either have reserved space (which we shouldn't do anything with in these two functions), an enum or a hexadecimal value, unsigned int seemed like the way to go. So all users of get_option now have their arguments inversed and switched from using ints to unsigned ints now. The way get_cmos_value was implemented forced us to not overlap byte and to have multibyte values be byte aligned. This logic is now adapted to do a full uint32_t read (when needed) at any offset and any length up to 32, and the shifting all happens inside an uint32_t as well. set_cmos_value was implemented similarly. Both routines have been extensively tested in a quick separate little program as it is not easy to get this stuff right. build_opt_tbl.c was altered to function correctly within these new parameters. The enum value retrieval has been changed strol(..., NULL, 10) to stroul(..., NULL, 0), so that we not only are able to use unsigned ints now but so that we also interprete hex values correctly. The 32bit limit gets imposed on all entries not marked reserved, an unused "user_data" field that appeared in a lot of cmos.layouts has been changed to reserved as well. Signed-off-by: Luc Verhaegen <libv@skynet.be> Acked-by: Peter Stuge <peter@stuge.se> git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4332 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
2009-06-03Modify it based on the RPR 5.7.7. Switching GGSP Configuration By Register ↵Zheng Bao
Programming. Signed-off-by: Zheng Bao <zheng.bao@amd.com> Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net> git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4331 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
2009-03-06use include file for i8259 where appropriate (trivial)Stefan Reinauer
Signed-off-by: Stefan Reinauer <stepan@coresystems.de> Acked-by: Stefan Reinauer <stepan@coresystems.de> git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3980 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
2009-03-04I just went on a bugfix frenzy and fixed all printk format warningsCarl-Daniel Hailfinger
triggered by the AMD 690/SB600 targets. Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net> Acked-by: Stefan Reinauer <stepan@coresystems.de> git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3970 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
2009-02-28coreboot-v2: drop this ugly historic union name in v2 that was dropped in v3Stefan Reinauer
a long time ago. This will make it easier to port v2 boards forward to v3 at some point (and other things) Signed-off-by: Stefan Reinauer <stepan@coresystems.de> Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net> git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3964 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
2009-02-15- Fix up amd pistachio and dbm690t.Stefan Reinauer
- make uma_memory_base and uma_memory_size uint64_t as they may be 64bit BARs on some platforms. Signed-off-by: Stefan Reinauer <stepan@coresystems.de> Acked-by: Stefan Reinauer <stepan@coresystems.de> git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3949 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
2009-02-12This patch converts __FUNCTION__ to __func__, since __func__ is standard.Myles Watson
Signed-off-by: Myles Watson <mylesgw@gmail.com> Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net> git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3943 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
2009-02-05Use the correct device for switching on HDA.Dan Lykowski
Reorder HDA (HD Audio) init: The reordering was based on what order things happen in the BIOS Developers guide, RPR, and SATA driver. I fixed the order of the devices that didn't matter to clean up the change log. 1. Enable the Chip 2. Setup the SMBus registers 3. Setup the Device Registers 4. Look for Codec 5. Init Codec The codec init was changed to match the description in the RRG pg 235. Mem Reg: Base + 08h Bit 0. There were unneeded things happening. Added 1ms delay to match the BKDG while waiting for BAR+0xe to set its bits. Signed-off-by: Dan Lykowski <lykowdk@gmail.com> Tested on AMD DBM690T and AMD Pistachio by Maggie Li. Works. Tested on Asus M2A-VM by Carl-Daniel Hailfinger. Improves the situation, but some warnings remain. Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net> git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3930 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
2009-01-23Fix rs690 bug about GPPSB configuration.Maggie Li
Signed-off-by: Maggie Li <maggie.li@amd.com> Reviewed-by: Zheng Bao <Zheng.bao@amd.com> Acked-by: Marc Jones <marcj303@gmail.com> git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3891 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
2009-01-15Adds a retry/faildown to SB600 SATA detection logic.Dan Lykowski
SATA port status kept returning 0x1: BAR5+po+28h 1h = Device presence detected but Phy communication not established This patch adds logic to force 1.5g if the drive fails to communicate at 3.0g. Signed-off-by: Dan Lykowski <lykowdk@gmail.com> Acked-by: Peter Stuge <peter@stuge.se> git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3864 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
2008-12-29The SB600 RPR documentation does not mention what to do if SATA_BAR0+6Carl-Daniel Hailfinger
is no longer 0xA0 or 0xB0. It simply assumes that will never happen. My 500 GB Seagate Barracuda ST3500820AS triggers that corner case on the first init after poweron. The current code hangs forever with my drive. Fix this by rerunning the init sequence after SATA_BAR0+6 is no longer 0xA0 or 0xB0. Add support for SATA port 2-4 (Primary Slave, Secondary Master, Secondary Slave). If only the 2nd SATA port is connected and the hardware acts strangely (contrary to documentation), it will print the error message below and continue anyway. The official AMD asm code behaves the same way. SATA port 0 status = 0 No Primary Master SATA drive on Slot0 SATA port 1 status = 23 0x6=7f, 0x7=7f drive no longer selected after 0 ms, retrying init [8 repetitions] 0x6=7f, 0x7=7f drive no longer selected after 0 ms, retrying init Primary Slave device is not ready after 10 tries Activate and improve debug messages for SPEW log level. Fix some comments. New log messages look like this: PCI: 00:12.0 init sata_bar0=3020 sata_bar1=3060 sata_bar2=3030 sata_bar3=3070 sata_bar4=3000 sata_bar5=fc309000 SATA port 0 status = 23 0x6=a0, 0x7=80 drive detection not yet completed, waiting... 0x6=a0, 0x7=80 drive detection not yet completed, waiting... [... 281 repetitions ...] 0x6=0, 0x7=50 drive no longer selected after 2820 ms, retrying init drive detection done after 0 ms Primary Master device is ready after 2 tries SATA port 1 status = 23 drive detection done after 0 ms Primary Slave device is ready after 1 tries SATA port 2 status = 0 No Secondary Master SATA drive on Slot2 SATA port 3 status = 0 No Secondary Slave SATA drive on Slot3 With this patch, my Asus M2A-VM boots into Linux without problems. Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net> Acked-by: Zheng Bao <zheng.bao@amd.com> git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3845 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
2008-12-23Handle RS690 quirks for 1 GHz noncoherent HyperTransport.Carl-Daniel Hailfinger
The RS690 chipset has a problem where it will not work with 1 GHz HT speed unless NB_CFG_Q_F1000_800 bit 0 is set. Tested, works on my Asus M2A-VM with an 1 GHz HT capable processor. Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net> Bao, Zheng says: As a matter of fact, both 600Mhz and 1Ghz have their own specific setting. This patch has been tested on dbm690t which HT link works on 800Mhz. Acked-by: Peter Stuge <peter@stuge.se> git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3839 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
2008-12-23Fix implicit declarations of pci_read_config32 and pci_write_config32 inMaggie Li
the SB600 code. Signed-off-by: Maggie Li <Maggie.li@amd.com> Reviewed-by: Zheng bao <Zheng.bao@amd.com> Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net> git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3837 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
2008-12-18This patch gets rid of all the implicit definition warnings for serengeti ↵Myles Watson
except get_nodes. Signed-off-by: Myles Watson <mylesgw@gmail.com> Acked-by: Marc Jones <marcj303@gmail.com> git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3818 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
2008-12-17Add 690G and 690(MT) internal graphics support.Zheng Bao
The device ID of 690G is 0x791E, while the ID of 690M and 690T is 0x791F This fixes booting on 690G. Signed-off-by: Zheng Bao <zheng.bao@amd.com> Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net> git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3816 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
2008-12-13Move mainboard specific changes to the coreboot memory table into theStefan Reinauer
mainboard specific code. (And add a hook to allow other mainboards do a similar thing if required) Signed-off-by: Stefan Reinauer <stepan@coresystems.de> Acked-by: Ronald G Minnich <rminnich@gmail.com> git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3812 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
2008-12-12Improve comments in early SB600 setup, handle non-LPC strapping andCarl-Daniel Hailfinger
document verification against the data sheets. Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net> Acked-by: Maggie Li <maggie.li@amd.com> git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3811 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
2008-12-01Add AMD rs690 VID DID reporting and some minor cleanups.Joe Bao
Signed-off-by: Joe Bao <zheng.bao@amd.com> Reviewed-by: Maggie Li <maggie.li@amd.com> Acked-by: Ronald G. Minnich <rminnich@gmail.com> Acked-by: Marc Jones <marcj303@gmail.com> git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3786 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
2008-12-01Add AMD sb600 HPET setup and some minor cleanups.Joe Bao
Signed-off-by: Joe Bao <zheng.bao@amd.com> Reviewed-by: Maggie Li <maggie.li@amd.com> Acked-by: Ronald G. Minnich <rminnich@gmail.com> Acked-by: Marc Jones <marcj303@gmail.com> git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3785 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
2008-11-14drop dead code in sb600 hdaStefan Reinauer
Signed-off-by: Stefan Reinauer <stepan@coresystems.de> Acked-by: Myles Watson <mylesgw@gmail.com> git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3752 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
2008-10-21I/O ports are 16bit, so change 'unsigned long port_base' to 'u16 port_base'.Uwe Hermann
Also, use more readable #defines instead of hardcoded config ports for PM/PM2 related functions, and simplify them a bit. Build-tested with the AMD dbm690t target. Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de> Acked-by: Marc Jones <marc.jones@amd.com> git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3680 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
2008-10-21Add missing license header.Uwe Hermann
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de> Acked-by: Jordan Crouse <jordan.crouse@amd.com> git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3678 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
2008-10-13Move AMD RS690 and SB600 PCI IDs to pci_ids.h where they should be.Uwe Hermann
Build-tested with the AMD dbm690t board. Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de> Acked-by: Marc Jones <marc.jones@amd.com> git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3655 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
2008-10-09Added comment about sb600 wideio setting for clarity and a minor witespace ↵Marc Jones
cleanup. (trivial) Signed-off-by: Marc Jones <marcj.jones@amd.com> Acked-by: Marc Jones <marcj.jones@amd.com> git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3643 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
2008-10-07[PATCH] coreboot: Don't loop forever waiting for HDA codecsJordan Crouse
We shouldn't assume the presence of a working HDA codec, so put in a reasonable timeout of 50usecs (timeout value borrowed from the kernel). This makes SimNow work, since apparently though the codec is present in Simnow, it is non functional. Signed-off-by: Jordan Crouse <jordan.crouse@amd.com> Acked-by: Ronald G. Minnich <rminnich@gmail.com> git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3640 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
2008-10-03Ron has been doing really good work over in v3. The problem is that the work ↵Marc Jones
got checked into v2. This should get us back to where we were. (trivial) Signed-off-by: Marc Jones <marc.jones@amd.com> Acked-by: Marc Jones <marc.jones@amd.com> git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3636 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
2008-10-02This is so that people can see it. This is the sb600 for v3. It almost Ronald G. Minnich
certainly won't build -- that comes later. I am hoping to get some eyeballs on it for simple errors. rs690 is next. Signed-off-by: Ronald G. Minnich <rminnich@gmail.com> Acked-by: Ronald G. Minnich <rminnich@gmail.com> git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3630 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
2008-10-01The ARRAY_SIZE macro is convenient, yet mostly unused. Switch lots ofCarl-Daniel Hailfinger
code to use it. That makes the code more readable and also less error-prone. Abuild tested. Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net> Acked-by: Peter Stuge <peter@stuge.se> git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3624 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
2008-09-22Patch for AMD SB600 chipset.Michael Xie
Most of the functions in SB600 are enabled except power management. Signed-off-by: Michael Xie <Michael.Xie@amd.com> Reviewed-by: Marc Jones <marc.jones@amd.com> Acked-by: Stefan Reinauer <stepan@coresystems.de> git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3589 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
2008-09-22Patch for AMD RS690 chipset.Michael Xie
All the PCIe slots are enabled in this patch except power management. Signed-off-by: Michael Xie <Michael.Xie@amd.com> Reviewed-by: Marc Jones <marc.jones@amd.com> Acked-by: Stefan Reinauer <stepan@coresystems.de> git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3588 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
2008-07-12There was a programming error which made most USB port4 setup wrong. This ↵Marc Jones
patch uses byte pointer and the MMIO read and write functions. Signed-off-by: Marc Jones <marc.jones@amd.com> Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net> git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3421 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
2008-05-06cs5536 IDE PWB flag was not getting set since it is 1<<14 and it was only ↵Marc Jones
doing a pci_write_config8. Signed-off-by: Marc Jones <marc.jones@amd.com> Acked-by: Ronald G. Minnich <rminnich@gmail.com> git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3282 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
2008-03-29Now coreboot performs IRQ routing for some boards.Nikolay Petukhov
You can see this by executing commands like this: grep -r pci_assign_irqs coreboot/src/* This basically AMD/LX based boards: pcengines/alix1c, digitallogic/msm800sev, artecgroup/dbe61, amd/norwich, amd/db800. Also for AMD/GX1 based boards need a patch [http://www.pengutronix.de/software/ptxdist/temporary-src/references/geode-5530.patch] for the right IRQ setup. AMD/GX1 based boards is: advantech/pcm-5820, asi/mb_5blmp, axus/tc320, bcom/winnet100, eaglelion/5bcm, iei/nova4899r, iei/juki-511p. I have two ideas. 1. Delete duplicate code from AMD/LX based boards. 2. Add IRQ routing for AMD/GX1 boards in coreboot. The pirq.patch for IRQ routing logically consist from of two parts: First part of pirq.patch independent from type chipsets and assign IRQ for ever PCI device. It part based on AMD/LX write_pirq_routing_table() function. Second part of pirq.patch depends of type chipset and set PIRQx lines in interrupt router. This part supports only CS5530/5536 interrupt routers. IRQ routing functionality is included through PIRQ_ROUTE in Config.lb. Tested on iei/juki-511p(cs5530a), iei/pcisa-lx(cs5536) and also on TeleVideo TC7020, see http://www.coreboot.org/pipermail/coreboot/2007-December/027973.html. Signed-off-by: Nikolay Petukhov <nikolay.petukhov@gmail.com> Acked-by: Uwe Hermann <uwe@hermann-uwe.de> git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3196 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
2008-01-18Rename almost all occurences of LinuxBIOS to coreboot. Stefan Reinauer
Due to the automatic nature of this update, I am self-acking. It worked in abuild. Signed-off-by: Stefan Reinauer <stepan@coresystems.de> Acked-by: Stefan Reinauer <stepan@coresystems.de> git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3053 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
2008-01-18Please bear with me - another rename checkin. This qualifies as trivial, noStefan Reinauer
code is changed. Signed-off-by: Stefan Reinauer <stepan@coresystems.de> Acked-by: Stefan Reinauer <stepan@coresystems.de> git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3052 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
2007-12-19Additional early AMD8111 southbridge support for Barcelona platforms.Marc Jones
Check that the SMBus controller is found and stop on an error. Clean up and add additional path through the 8111 reset functions. Signed-off-by: Marc Jones <marc.jones@amd.com> Reviewed-by: Jordan Crouse <jordan.crouse@amd.com> Acked-by: Myles Watson <myles@pel.cs.byu.edu> git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3015 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
2007-10-24Ever wondered where those "setting incorrect section attributes forStefan Reinauer
rodata.pci_driver" warnings are coming from? We were packing those structures into a read-only segment, but forgot to mark them const. Despite its size, this is a fairly trivial patch created by a simple search/replace Signed-off-by: Stefan Reinauer <stepan@coresystems.de> Acked-by: Stefan Reinauer <stepan@coresystems.de> git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2891 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
2007-10-07Fix some issues with spaces in the code and Doxygen style documentation.Juergen Beisert
Painting the splash graphic is now ifdef'ed. Signed-off-by: Juergen Beisert <juergen127@kreuzholzen.de> Acked-by: Peter Stuge <peter@stuge.se> Acked-by: Uwe Hermann <uwe@hermann-uwe.de> git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2836 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
2007-10-05This patch will add support for the Geode GX1/CS5530 VGA feature. It's ableJuergen Beisert
to set up one of five screen resolutions (sorry no autodetection at runtime, resolution is selected at buildtime) and displays a graphic in the right bottom corner (splash screen). Signed-off-by: Juergen Beisert <juergen127@kreuzholzen.de> Acked-by: Ronald G. Minnich <rminnich@gmail.com> Acked-by: Stefan Reinauer <stepan@coresystems.de> git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2827 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
2007-09-14This is a full rewrite of all the CS5530/CS5530A code. The previous code wasUwe Hermann
mostly undocumented, had a broken coding style, contained lots of dead code and had several other problems, e.g. it enabled write access to the ROM (why?), it unconditionally enabled primary/secondary IDE (which should have a config option) and that even _twice_ (which is um... wrong). The new code - has 'ide0_enable' and 'ide1_enable' config options (which actually work) to enable/disable the primary/secondary IDE interface in Config.lb. - Does _not_ enable write access to the ROM (or is there some good reason to do that? If so, it should at least have a config option). - Contains a bit more documentation. - Uses readable (and documented) #defines instead of hardcoded magic values. - aaand... it actually compiles ;-) Yep, that's right. The previous code wouldn't even build, as it hadn't been fully ported from v1 (still used v1 functions which are simply not available in v2). Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de> Acked-by: Ronald G. Minnich <rminnich@gmail.com> git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2775 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
2007-06-19The GPIOs used for UART2 RX and TX were reversed.Marc Jones
Signed-off-by: Marc Jones <marc.jones@amd.com> Acked-by: Ronald G. Minnich <rminnich@gmail.com> Acked-by: Uwe Hermann <uwe@hermann-uwe.de> git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2726 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
2007-06-02The UART disable code was causing a hang and was worked around with aMarc Jones
return that skipped the disable code. This patch removes the return and fixes the UART disable code. The problem was that the disable code was ORing bits into the Legacy_IO MSR causing issues with the LPC SIOs init code that would manifest as a hang because the IO would not be decoded correctly. ANDing to clear the bits fixes the issue. Signed-off-by: Marc Jones <marc.jones@amd.com> Acked-by: Ronald G. Minnich <rminnich@gmail.com> Acked-by: Uwe Hermann <uwe@hermann-uwe.de> git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2706 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
2007-05-24Drop the src/southbridge/amd/cs5536_lx directory and its contents, asUwe Hermann
the new src/southbridge/amd/cs5536 code completely replaces it. The Artecgroup dbe61 board currently uses it, but that is broken anyway at the moment. A fix to use the new CS5536 code for it is being worked on. Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de> Acked-by: Stefan Reinauer <stepan@coresystems.de> git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2697 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
2007-05-22Add missing license headers, minor cosmetic fixes in existing headers.Uwe Hermann
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de> Acked-by: Marc Jones <marc.jones@amd.com> git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2687 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
2007-05-10This fix properly hides the UDC and OTG PCI headers when the cs5536 isMarc Jones
setup as the host on USB port4. In client mode the headers remain available. Also fixes an outb to 0x80 to use the post_code() function. Signed-off-by: Marc Jones <marc.jones@amd.com> Acked-by: Stefan Reinauer <stepan@coresystems.de> git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2660 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
2007-05-10This patch cleans up and clarifies Geode source code comments.Marc Jones
Signed-off-by: Marc Jones <marc.jones@amd.com> Acked-by: Stefan Reinauer <stepan@coresystems.de> git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2658 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
2007-05-10This patch updates the PCI ID of the Geode IDE device to include the revision.Marc Jones
Signed-off-by: Marc Jones <marc.jones@amd.com> Acked-by: Peter Stuge <peter@stuge.se> git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2656 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
2007-05-10Fix the indent and whitespace to match LinuxBIOS standardsJordan Crouse
Signed-off-by: Jordan Crouse <jordan.crouse@amd.com> Acked-by: Stefan Reinauer <stepan@coresystems.de> git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2651 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
2007-05-10Add missing licenses to several of the files.Jordan Crouse
Signed-off-by: Jordan Crouse <jordan.crouse@amd.com> Acked-by: Stefan Reinauer <stepan@coresystems.de> git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2647 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
2007-05-05With this patch, the msm800sev runs FILO and boots a kernel.Ronald G. Minnich
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com> Acked-by: Stefan Reinauer <stepan@coresystems.de> -This line, and those below, will be ignored-- M cs5536.c git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2637 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
2007-05-04This patch re-implements support for the CS5536 companion chip for theMarc Jones
AMD GX and LX processors. This aguments the previous code, which was very specific to the OLPC platform with general purpose support and better integration with the VSA and CPUs. Signed-off-by: Marc Jones <marc.jones@amd.com> Acked-by: Stefan Reinauer <stepan@coresystems.de> git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2631 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
2006-11-05Use the canonical name of the vendors/devices and theUwe Hermann
same format for all CHIP_NAME() entries in LinuxBIOS (Closes #20). Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de> Acked-by: Stefan Reinauer <stepan@linuxbios.org> git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2490 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
2006-10-04AMD Rev F supportYinghai Lu
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2435 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
2006-09-20Lots of lx fixes. CLeanup mainly. THings now buildRonald G. Minnich
Signed-off-by: Ronald G. Minnich git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2430 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
2006-09-19put this in the right place.Ronald G. Minnich
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2425 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
2006-09-18add the _lx flavor of the 5536. This will later be merged into the Ronald G. Minnich
cs5536, but I don't want to mess up the OLPC, and we really need the lx support NOW. git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2421 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
2006-09-13add file for dcon supportJordan Crouse
signed-off-by: Jordan Crouse Signed-off-by: Ronald G. Minnich git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2410 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
2006-08-28- Much better USB P4 fix. Richard Smith
This one actualy works. You cannot just go mucking about with stuff that the VSA has under its thumb. Bad Things happen. This does it the VSA way. git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2392 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
2006-08-25- USB P4 as host fixRichard Smith
This should make the USB P4 work as a USB host git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2389 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
2006-08-25- fix a silly pointer dereference thinko in my previous commitRichard Smith
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2388 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
2006-08-25- Added suport for enabling USB P4 on the olpcRichard Smith
USB P4 is disabled by default and we need to setup the mux bits proper to make it work. This is the frame work for that. All thats needed is the right address values git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2387 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
2006-08-15this file is already included by auto.c on all targets.Stefan Reinauer
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2377 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
generated by cgit v1.2.3 (git 2.39.1) at 2024-07-16 13:33:19 +0000