| Age | Commit message (Collapse) | Author |
|---|
|
Modify the previously SOC_CNL_LPDDR4_INIT to SOC_CNL_MEMCFG_INIT, to
make the infrasturture to handle both LPDDR4 and DDR4 cases in the
future. Consider the case of reading SPD from SMBus other than providing
SPD pointer directly.
BUG=N/A
TEST=Verify "./util/abuild/abuild -p none -t google/zoombini -x -a"
compiles successfully.
Change-Id: I2f898147f67dd52b89cc3d9fc4e6b3854fa81f57
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/28248
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The firmware of devices connected to LPC should deassert the LPC CLKRUN#
signal when there is no bus activity on LPC.
Necessary changes:
- Enable LPC CLKRUN#
- Enable LPC PCE (Power Control Enable)
- Enable LPC CCE (Clock Control Enable)
- Remove I/O decoding range on LPC for COM 3
- Disable I/O UART driver
Change-Id: I2fd80e3fdcf23658f97b8182a77df7e09ddf25d6
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/28268
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Use get_acpi_table_revision(HPET) to keep all table versions in sync.
Change-Id: Idb5e8ccd49ec27f87a290f33c62df3c177645669
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/28278
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Most FADT report using ACPIv3 FADT table. Using the get revision
function keeps the table versions in sync.
Change-Id: Ie554faf1be65c7034dd0836f0029cdc79eae1aed
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/28277
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
The eMMC maximum speed is set to HS400 mode per default. To increase the
lifetime of the circuit, it is necessary to reduce the eMMC speed.
Change-Id: I6fa5eb56a0593e24269ef143645c506232879889
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/28282
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
* Add VERSTAGE and VBOOT_WORK to memlayout.
* Add hard and soft reset.
* Add missing makefile and kconfig includes.
Change-Id: I0d7e3c220f5c2c50c4ffe59ac929cb865bfac0ad
Signed-off-by: Philipp Deppenwiese <zaolin@das-labor.org>
Reviewed-on: https://review.coreboot.org/28022
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
As preparation to constify devicetree data, do it the right way.
Change-Id: I5081de020bb73c56aa8bdf7bb17fe6b2913d0ffe
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/28266
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
|
|
* Add const quailifier to arguments and elements.
* Add casts where necessary in cn81xx/soc.
Tested on Cavium CN81xx EVB SFF.
Change-Id: Id27966427fb97457fe883be32685d1397fb0781f
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/28267
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
src/soc/intel/apollolake/chip.c
Apply bitwise operator instead of logical one.
Found-by: Coverity Scan
BRANCH=None
TEST=Built & booted Yorp board.
Change-Id: I36746b04dec889f53c8d7eeb3b1d8118eff1de42
Signed-off-by: John Zhao <john.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/28261
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
There's a small window of opportunity when CPU is already in SMM but has
not yet entered S3 for a wake event to happen, which would cause a failed
S3 entry. Check for pending events at the very last moment possible, and
if there are pending wake events report them.
BUG=b:111100312
TEST=build and boot grunt.
Change-Id: I9472fdf481897fcf9f4c669f6b1514ef479fce7a
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/28247
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Since we can derive chromeos_acpi's location from that of
ACPI GNVS, remove chromeos_acpi entry from cbtable and
instead use acpi_gnvs + GVNS_CHROMEOS_ACPI_OFFSET.
BUG=b:112288216
TEST=None
CQ-DEPEND=CL:1179725
Change-Id: I74d8a9965a0ed7874ff03884e7a921fd725eace9
Signed-off-by: Joel Kitching <kitching@google.com>
Reviewed-on: https://review.coreboot.org/28190
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Since we can retrieve the address of ACPI GNVS directly
from CBMEM_ID_ACPI_GNVS, there is no need to store and
update a pointer separately.
TEST=Compile and run on Eve
Signed-off-by: Joel Kitching <kitching@google.com>
Change-Id: I59f3d0547a4a724e66617c791ad82c9f504cadea
Reviewed-on: https://review.coreboot.org/28189
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Some OS certification test (for example Windows) will fail if there
are unsupported sleep states. Since these states are not really used
today, we can remove them from ACPI table.
BRANCH=eve
BUG=b:72197653
TEST=certification system sleep test pass.
Change-Id: I5f5122cac1bf61f7c580afb18cc66b5ff07286fb
Signed-off-by: Lucas Chen <lucas.chen@quanta.corp-partner.google.com>
Reviewed-on: https://chromium-review.googlesource.com/1065401
Commit-Queue: David Wu <david_wu@quanta.corp-partner.google.com>
Tested-by: David Wu <david_wu@quanta.corp-partner.google.com>
Reviewed-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: https://review.coreboot.org/28080
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
In legacy mode, DPTF on some systems may rely on MMIO to control PL1
settings. However, MSR PL1 also contributes to the decision of max
PL1 power; and in the current design, the lower value takes effect.
In order to align MMIO and MSR settings, a tdp_pl1_override option is
added to override the MSR PL1 limitation.
BRANCH=eve
BUG=b:73133864
TEST=1. Write PL1 override setting in devicetree.cb
2. Verify the MSR PL1 limitation is set correctly.
Change-Id: I35b8747ad3ee4c68c30d49a9436aa319360bab9b
Signed-off-by: Lucas Chen <lucas.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/28079
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
ACPI 5.0 defines a method _CPC for "Continuous Performance Control" (CPPC).
Linux has a driver that enables features like speed shift without
consulting ACPI. Other OSes instead rely on this information and need a
_CPC present. Prior to this change performance in Win10 never exceeds
80% and MSR 0x770 is 0, while with this change (and enabling eist) higher
speeds can be achieved and the MSR value is now 1.
Change-Id: Ib7e0ae13f4b664b51e42f963e53c71f8832be062
Signed-off-by: Matt Delco <delco@chromium.org>
Reviewed-on: https://review.coreboot.org/27673
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
This patch moves uart functions which are common across multiple soc to
block/uart. This will remove redundant code copy from soc
{skylake/apollolake/cannonlake}.
BUG=b:78109109
BRANCH=none
TEST=Build and boot on KBL/APL/CNL platform.
Change-Id: I109d0e5c942e499cb763bde47cb7d53dfbf5cef6
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/26164
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
There are two SKUs of Whiskey Lake W0, 2-core and 4-core.
Change-Id: Ia9b2707568702a5fbae3e9495ca53df34613a542
Signed-off-by: Krzysztof Sywula <krzysztof.m.sywula@intel.com>
Reviewed-on: https://review.coreboot.org/28111
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
When USB OTG is set, GLK FSP enables xHCI SW ID pin and configures
USB-C as device mode. Force USB-C into host mode.
BUG=b:111623911
TEST=Verified that USB-C being host mode once USB OTG is set.
Change-Id: Iaca3d25a1159f922b743963cbc508d8defa7b6ff
Signed-off-by: John Zhao <john.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/27746
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
src/soc/intel/common/block/cpu/mp_init.c
Function init_cpus: Pointer dev checked for NULL may be
dereferenced.
src/soc/intel/common/block/graphics/graphics.c
Function graphics_get_bar: Pointer dev returned from
call may be NULL and will be dereferenced.
BRANCH=None
TEST=Built & booted Yorp board.
Change-Id: I5e7caa15a3911e05ff346d338493673af5318a51
Signed-off-by: John Zhao <john.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/28060
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
The romstage main() entry point on arm64 boards is usually in mainboard
code, but there are a handful of lines that are always needed in there
and not really mainboard specific (or chipset specific). We keep arguing
every once in a while that this isn't ideal, so rather than arguing any
longer let's just fix it. This patch moves the main() function into arch
code with callbacks that the platform can hook into. (This approach can
probably be expanded onto other architectures, so when that happens this
file should move into src/lib.)
Tested on Cheza and Kevin. I think the approach is straight-forward
enough that we can take this without testing every board. (Note that in
a few cases, this delays some platform-specific calls until after
console_init() and exception_init()... since these functions don't
really take that long, especially if there is no serial console
configured, I don't expect this to cause any issues.)
Change-Id: I7503acafebabed00dfeedb00b1354a26c536f0fe
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/28199
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
In preparation to removing AmdLib, replace function LibAmdLocateImage()
with its ported version find_image().
BUG=b:112625809
TEST=Build and boot grunt.
Change-Id: I75ddd55f7e3e7f2cd7914f97c99b62690ae70660
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/28164
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
In preparation to removing AmdLib, function LibAmdLocateImage() has to be
ported to be used by agesawrapper. The most important aspect of this porting
is that it has to obey coreboot format, specifically 8 character tab and 80
characters max. This required breaking the function in 2 (to solve
indentation) and rename some variables to shorter names.
One important aspect was breaking
(AMD_MODULE_HEADER*)(((AMD_IMAGE_HEADER *) CurrentPtr)->ModuleInfoOffset)
into:
image_ptr = (AMD_IMAGE_HEADER *) current_ptr;
if (validate_image((void *)image_ptr->ModuleInfoOffset,
and, within validate_image completed by:
AMD_MODULE_HEADER *mod_ptr = (AMD_MODULE_HEADER *)module_chain;
BUG=b:112625809
TEST=Build grunt, functionality tested in next commit.
Change-Id: I0d1e8b966cf7606fdb15a95de5771f835f07b2bc
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/28144
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Fix the IASL build warnings:
Object is not referenced (Name [CDW2] is within a method [_OSC])
Object is not referenced (Name [CDW3] is within a method [_OSC])
Remove the not referenced objects. They are not needed.
BUG=b:112476331
TEST=IASL doesn't give the warning.
Change-Id: I5b38d4de3f9875c5b013a49eb5146bf5916b96a6
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/28121
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
This change permits the subsystem ID to be specified via Kconfig for the
devices on the SoC.
Some devices are getting zero'ed subsystem IDs because the unset (and thus
zero'ed) config options are overwriting the fsp defaults. With this change
the fsp defaults will only be overwritten by non-zero config values.
Change-Id: I0f7bb8e465f55e5dd6d8e0fad71b9b2a22f089dc
Signed-off-by: Matt Delco <delco@chromium.org>
Reviewed-on: https://review.coreboot.org/27609
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Print the PMxC0 S5/Reset status bits to the console.
TEST=Inspect console for Grunt
BUG=b:110788201
Change-Id: Ia905bb325a535fd4aa7082011cdfe92f08dff2cb
Signed-off-by: Edward Hill <ecgh@chromium.org>
Reviewed-on: https://review.coreboot.org/28020
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Remove VENDORCODE_FULL_SUPPORT from /soc/amd/stoneyridge/Kconfig and
from vendorcode/amd/pi/00670F00/Makefile.inc, thus completing the removal
of VENDORCODE_FULL_SUPPORT from coreboot.
BUG=b:112578491
TEST=none, VENDORCODE_FULL_SUPPORT already not used.
Change-Id: Idb5f6dc7add1617f7a97a97ae110901b2dec0996
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/28092
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Add a method in bootblock that can be used for printing registers.
BUG=none
TEST=compiled grunt
Change-Id: I8dff30e589761fbad92cfc2709546dba169993d8
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Reviewed-on: https://review.coreboot.org/28059
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
All broadwell board set HAVE_IFD_BIN to default n, overloading the option in
soc, therefore just use the defaults in sb/intel/common/firmware.
Change-Id: I250dbbc9d61ecedc1a1eb48751ad966732604349
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/28011
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tristan Corrick <tristan@corrick.kiwi>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
There is no need to redefine option present in
southbridge/intel/common/firmware/Kconfig.
FAKE_IFD depends on out tree flashrom patches for which there are better
alternatives available now, so don't build with FAKE_IFD by default.
Change-Id: Icd41137a1bbfe519c89a71cc0c7c3755558bd834
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/28010
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tristan Corrick <tristan@corrick.kiwi>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Fix to accomodate for boards with more than 16 cores.
Change-Id: I35b61d94491c21ef76717f761e566ca815880f27
Signed-off-by: Samuel Jimenez <aerojsam@gmail.com>
Reviewed-on: https://review.coreboot.org/27847
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
There's two cases of 1 being used. This changes the
eighth instance to use 8.
Change-Id: I7057a4345dadcc6f8fb43093844d27007444f481
Signed-off-by: Matt Delco <delco@chromium.org>
Reviewed-on: https://review.coreboot.org/27603
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
This patch changes the mapping of SRAM from non-secure to secure.
Without this patch, mmu_config_range() can not work when MMU is
enabled. The new config is still in non-secure cache since TTB section
is allocated in SRAM which is mapped as non-secure.
BUG=b:80501386
TEST=Boots correctly on Kukui and Elm
Change-Id: Ia5b8716cfcca64d1d716a177225ea2f7ac2920a6
Signed-off-by: Tristan Shieh <tristan.shieh@mediatek.com>
Reviewed-on: https://review.coreboot.org/27974
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Fix define typo in dptf.asl
BUG=none
TEST=emerge-octopus coreboot PASS
Change-Id: I1c3bd55d1507e6fffe638bba38c99a9851b8a96a
Signed-off-by: Chris Zhou <chris_zhou@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/28001
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
|
|
Add DRAM resource in ramstage to load payload.
BUG=b:80501386
TEST=Load bl31 and depthcharge correctly on Kukui with more patches
applied.
Change-Id: Ie793b403bbbdb3c231dfa2caef29dcbb596b1a61
Signed-off-by: Tristan Shieh <tristan.shieh@mediatek.com>
Reviewed-on: https://review.coreboot.org/27971
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
* Needed for additional code in later patches.
* SOC is obsolete anyway.
Change-Id: I5bbdf19cc886103e9e7a6b75219d6881cfe9c757
Signed-off-by: Philipp Deppenwiese <zaolin@das-labor.org>
Reviewed-on: https://review.coreboot.org/23764
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
There is no need to add a special cnvi.asl file for the CNVi
device. This can be handled by drivers/intel/wifi just like a PCIe
WiFi device. This change gets rid of the cnvi.asl file and its usage
in southbridge.asl file.
BUG=b:112371978
Change-Id: I0b798cdd430768730b7ada61ca4cb1f63c2a4229
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/27992
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This change adds CNVi device to list of PCI devs.
BUG=b:112371978
Change-Id: I6def98db3846c2244812a9a2ce84340bd2149b48
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/27960
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Change-Id: Ib0839933f8b59f0c87cdda4e5374828bd6f1099f
Signed-off-by: Philipp Deppenwiese <zaolin@das-labor.org>
Reviewed-on: https://review.coreboot.org/23759
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
|
|
* Move cbmem.c to cn81xx folder
* Store CBMEM below 4 GiB
* Make sure CBMEM doesn't overlap with ATF scratchpad
* Fix ATF scratchpad not marked as reserved due to wrong calculation
* The scratchpad is the last 1 MiB at the end of DRAM.
Tested on Cavium CN81xx EVB:
The ATF scratchpad is now marked reserved and the configuration tables
are located below 4 GiB. Linux still boots.
Change-Id: Ibbc8b586f04bd6867c045f5546b32a77c057ac74
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/27955
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
It's broken.
Change-Id: I3ec8fff99e21cbdf4ad3f4562ff9bbc1cd3c135b
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/28003
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
|
|
Change-Id: I689c5663ef59861f79b68220abd146144f7618de
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/27988
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
1. Add new device IDs for SATA, GT and Northbridge to pci_ids.h
2. Add entry to identify CFL U GT and CPU to respective files
3. Add entry to identify CFL U to report_platform.c
BUG=none
BRANCH=none
TEST=Boot to CFL U RVP board with this patch and check if coreboot is
able to enumerate various devices and display correct component names properly
in serial logs.
Change-Id: I47c97fb9eb813587cd655e2bce05a686091619ed
Signed-off-by: Maulik <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/27522
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Naresh Solanki <naresh.solanki@intel.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
|
|
CNTFRQ_EL0 is a normal AArch64 architectural register like hundreds of
others that are all accessed through the raw_(read|write)_${register}()
family of functions. There's no reason why this register in particular
should have an inconsistent accessor, so replace all instances of
set_cntfrq() with raw_write_cntfrq_el0() and get rid of it.
Change-Id: I599519ba71c287d4085f9ad28d7349ef0b1eea9b
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/27947
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
I'm pretty sure this SoC doesn't actually exist.
Change-Id: I53e268ee1795e524a2a4562d67a2b9f28af966d1
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/27965
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I8053d0f0863aa4d93692487f1ca802195c2d475f
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/27908
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
RK3288 has always been notoriously low on SRAM, to the point where its
boards have less than 100 bytes left in both their bootblock/verstage
sections. This becomes a problem every time we try to add a tiny amount
of code to common coreboot interfaces that are included in them.
This patch manages to add another KB to each, one from the CBMEM console
(which now might get cut off a bit, but that's life) and one by moving
the TTB_SUBTABLES to PMUSRAM. PMUSRAM is a weird world where write
accesses must always be exactly 4 bytes long or they hang the CPU, so we
mostly ignore it... but thankfully, page table entries are exactly 4
bytes long and that's the only thing we write to this region, so it
works out in this case.
Change-Id: I5aecd66db40b3f52299b270322b8c8784dbe7e6f
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/27950
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
By setting this register in bootblock AmdInitEnv will no longer trigger
a reset in romstage. This fixes a few vboot test failures and also
speeds up boot time.
BUG=b:111610455
TEST=Built grunt and made sure bootblock only happens once on cold boot,
and S3 resume.
Change-Id: Ie19f7a14deaef45ac63156bec6946273c1b9447e
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Reviewed-on: https://review.coreboot.org/27876
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Add a function to provide a rudimentary dump of the Machine Check
Architecture registers. These values survive a warm reset.
BUG=b:65445599
TEST=Verify on a Grunt having propensity for #MC errors
Change-Id: Ib6875cabe3041e65c811d8b2232f7ac6bedd1a02
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/27926
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Extend the existing reset handling features in Stoney Ridge to plan for,
and recognize, warm resets. The ColdRstDet bit is always zero on a cold
reset, and is intended as a mechanism for the BIOS to determine the type
of a reset that occurred.
Set ColdRstDet=1 after all cores have been initialized, so that any
subsequent reset may be identified as warm/cold. A later patch will check
the value during mp_init.
Change-Id: I90255918de03018c9f090bff1e56a8bda5e7365e
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/27924
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Use the value discovered in the MCG_CAP[Count] for the number of MCA
status registers to clear. The generations should have the following
number of banks:
* Family 10h: 6 banks
* Family 12h: 6
* Family 14h: 6
* Family 15h: 7
* Family 16h: 6
Change-Id: I0fc6d127a200b10fd484e051d84353cc61b27a41
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/27923
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Change the defined name of MCI_STATUS (i.e. MCi_STATUS) to reflect its
MC0_STATUS address.
Change-Id: I97d2631a186965bb8b18f544ed9648b3a71f5fb0
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/27922
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
The current call for saving dimm info passed the lpddr4_cfg and
memory sku id. In order to prepare decoupling the part number
from lpddr4_cfg provide a new API, save_lpddr4_dimm_info_part_num(),
which explicitly takes the part number. The previous API now
uses the new one internally.
BUG=b:112203105
Change-Id: Ieadf452b6daa3231a0c5e3be61b0603b40d0fff2
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/27944
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
nWR (Write-Recovery for AutoPre-charge commands), the programmed value of nWR
is the number of clock cycles the LPDDR4-SDRAM device uses to determine the
starting point of an internal Pre-charge operation after a Write burst with
AP (auto-pre-charge) enabled. For >2133MHz speed parts the nWR needs to
be set to 24 clock cycles. The nWR field, though, is only in the GLK
FSP, so just update that field conditionally based on the GLK Kconfig
option.
BUG=b:112062440
TEST= build test
Change-Id: I1147538f72f4e2f14e32f3657c05f1f505a56fbf
Signed-off-by: Ravi Sarawadi <ravishankar.sarawadi@intel.com>
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/27850
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
In procedure generate_cpu_entries(), the code was copied from code that
could change variables "plen" and "pcontrol_blk" based on number of cores.
This is not the case with stoneyridge (2 cores only), and there's no need
to use the variables. Remove them and replace with fixed values.
BUG=b:112253891
TEST=Build and boot grunt.
Change-Id: I0258b19960b050e8da9d218ded3f1f3bfccad163
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/27877
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This implementation updates the chip select control register
programming in gspi controller setup call to program the correct
bit fields for chip select state.
Change-Id: Ifab37b0003f09a680024d5b155ab0bb157920a53
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-on: https://review.coreboot.org/27889
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This patch replaces the UART in the bootblock of SDM845 with a bitbang
implementation. Since SDM845 hardware UART needs a firmware blob loaded
into it before it becomes usable, it is not really suited for use in the
bootblock (since by the time we can read blobs from SPI, the bootblock
is essentially over anyway). This solution allows us to still have some
console output during early SoC initialization.
Change-Id: I0c252ec83a7993edce5c4debc687f1fdd0d7b36d
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/25813
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
AMD ALIB Function 1 accepts the AC/DC startup state. This
is reported to be required for AMD PSPP settings.
BUG=b:112020107
TEST= build test
Change-Id: Ibb6c872d84745217912956c15d6ca2e8ba387561
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/27785
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Now that an updated bootloader with important fixes is available at coreboot
repository, all stoneyridge boards should use it. Move the selection of
SOC_AMD_PSP_SELECTABLE_SMU_FW from mb/google/kahlee to soc/amd/stoneyridge.
BUG=b:111428800
TEST=Build and boot grunt.
Change-Id: Idf8e348efbc85569aa1163125f412c5242c46eb4
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/27844
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch revises IGD naming and adds AML IGD in platform reporting.
BUG=None
BRANCH=None
TEST=emerge-atlas coreboot chromeos-bootimage & Ensure AML IGD is shown
in platform reporting.
Change-Id: Id8f8379703abdaa5b14a4337a4fca04b370f3a2a
Signed-off-by: Gaggery Tsai <gaggery.tsai@intel.com>
Reviewed-on: https://review.coreboot.org/27846
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This patch adds AML IccMax for VR configuration. From doc #594883, the
IccMax for Core was changed to 28A, we need this patch to accommodate
the changes. Besides, removes unused sku information from
sku_icc_max_mapping structure.
BUG=b:110890675
BRANCH=None
TEST=Remove icc_max from DT &
emerge-atlas coreboot chromeos-bootimage &
Tested with AML-Y and KBL-Y SKUs.
Change-Id: Ic22bae162b58b06b9519f1b708be55bde5e4641e
Signed-off-by: Gaggery Tsai <gaggery.tsai@intel.com>
Reviewed-on: https://review.coreboot.org/27610
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
setup_spread_spectrum is called in early_init, meaning the console is
not initialized yet. So you won't see boot block booting twice.
BUG=b:111610455
TEST=booted grunt and verified that AmdInitReset does not reboot. I had
AGESA patched to skip the JTAG check.
Change-Id: Ia036ea513ac67d4b8bcf5a78029d969a4ae012a6
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Reviewed-on: https://review.coreboot.org/27813
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Grunt boards don't use SATA, so it should be disabled to save power.
Check if SATA is enabled in devicetree, and enable/disable the device
based on that setting.
BUG=b:112139043
TEST=Buil and boot grunt, checked the absence of SATA PCI.
Change-Id: I4a3b5f65e612e8da5bedff0c557a0850f350dfa8
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/27845
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
For some reason the PSPP setting was being overwritten in the common
code. Remove the setting and allow the oem customize function to
make the setting.
BUG=b:112020107
TEST= build test
Change-Id: If7f4511a71f725fedd60d33552656850e50d955d
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/27783
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
According to #574725, report Whiskey Lake CPUID, MCH device ID and
graphics device ID in bootblock stage.
BUG=N/A
TEST=Build and boot up whiskey lake rvp platform and check serial log to
see proper CPU/MCH/GFX/PCH got recognized.
Change-Id: I3fbc190e0520989d2fd4a9b3294e84d67e49b2cf
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/27756
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Pratikkumar V Prajapati <pratikkumar.v.prajapati@intel.com>
|
|
Add coffeelake config and include path to coffeelake fsp header files.
BUG=N/A
TEST=Using private mainboard file can boot up on coffeelake rvp
platform.
Change-Id: Ide180de32a9d1896bed85b9e093963721c3d6041
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/27468
Reviewed-by: Pratikkumar V Prajapati <pratikkumar.v.prajapati@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Adapted from chromium commit 126d352
[Strago: switch Touchpad and Touchscreen interrupts to be level-triggered]
The Elan and other touch controllers found in this device work much
more reliably if used with level-triggered interrupts rather than
edge-triggered.
TEST=Boot several cyan boards, verify that touchpad and touchscreen
work.
Original-Change-Id: I59d05d9dfa9c41e5472d756ef51f0817a503c889
Original-Signed-off-by: Dmitry Torokhov <dtor@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/894689
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Change-Id: Ia4f8cf83351dae0d78995ce0b0ed902d1e4ac3e8
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/27759
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Introduces new and required GPIO APIs, using common pinmux
definitions for GPIO configuration.
TEST=build & run
Change-Id: I8cef9dae2072da32cb0678efefeb8f0070cdde9c
Signed-off-by: David Dai <daidavid1@codeaurora.org>
Reviewed-on: https://review.coreboot.org/26233
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
2 bits of LPC host control were originally not public, and wrongly
identified as IMC related. Now that the bits are available in public BKDG,
fix the naming of the bits.
BUG=b:111912080
TEST=build and boot grunt.
Change-Id: I1921f46c6be54eda6329c98267cec27004caadd5
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/27744
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Specifically PCI device ID for graphics and PCI device ID for northbridge.
Change-Id: Ide237d3274df0543409c8a23b9bb50c8e0a6b7a3
Signed-off-by: Krzysztof Sywula <krzysztof.m.sywula@intel.com>
Reviewed-on: https://review.coreboot.org/27519
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Kin Wai Ng <kin.wai.ng@intel.com>
|
|
Per AMD, the Integrated Micro Controller is not a supported feature of
the Stoney Ridge APU. Systems are expected to implement an external EC
for desired features. Remove all stoney IMC files and functions from
src/soc/amd/stoneyridge.
There are 2 "IMC bits" left (and used) that are not truly IMC. New BKDG
describe these bits, so a new patch will be released later to fix the
names and comment.
BUG=b:111780177
TEST=Build grunt and gardenia
Change-Id: I6a24e4c3f03d04713a030b884c611d9c64c4cb3a
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/27651
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The careena board needs different video settings to pass eye diagram test,
which does not affect negatively the grunt board. In preparation for new
VBIOS, create code that allows changing eDP training parameter.
BUG=b:111673328
TEST=Tested in child patch.
Change-Id: Ic0452618bfc5e05b9ef8280bb8ba398ec7b4ce95
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/27625
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
RTC BUC control register provides a software interface to
configure the top swap feature. This patch adds implementation
to enable/disable top swap feature and gets it accessible in
romstage as well.
The top swap control functions are exposed only if INTEL_HAS_TOP_SWAP
is selected.
To use the topswap feature a second bootblock has to be added
to the cbfs. Below configs aid in doing that,
INTEL_HAS_TOP_SWAP
INTEL_ADD_TOP_SWAP_BOOTBLOCK
INTEL_TOP_SWAP_BOOTBLOCK_SIZE
Enabling and Disabling topswap, using the added API enables user
to boot alternatively from either bootblock.
Change-Id: Iea31b891f81e76d4d623fcb68183c3ad3dcadbad
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/25805
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Use precompiled BL31 from blobs repo.
There's no check for USE_BLOBS here as the included file is "free":
The BL31 is Open-Source and licensed under BSD.
Change-Id: I7e9eb429d11150d43aa070d1bd6a11ea71951ce3
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/25751
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
|
|
The register X1 isn't used. Document it and remove it.
Change-Id: I9324ea9de24ba4baaef9dde890c443dd0f921ad9
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/23792
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
|
|
* Add vbnv_cmos_failed function to SoC.
* Add VBOOT starts in romstage select.
Change-Id: I90a051e2b8d303c918bef976d0bb07aae0b1f5b3
Signed-off-by: Philipp Deppenwiese <zaolin@das-labor.org>
Reviewed-on: https://review.coreboot.org/27728
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
Since the TPM software stack refactoring static
TPM ACPI code isn't needed anymore.
Change-Id: I36a99cbc420ecfa55aa5c89787151d482225adf2
Signed-off-by: Philipp Deppenwiese <zaolin@das-labor.org>
Reviewed-on: https://review.coreboot.org/27715
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add internal graphics device 00.01.00 to the ACPI tables so that the
ACPI PCI option ROM save functions have a proper scope to save the
ROM to.
BUG=b:111697181
TEST=Check coreboot log doesn't have "PCI: 00:01.0: Missing ACPI scope"
and check _ROM method is added in the SSDT1.
Change-Id: I2c9ef8d9dff76805b1fcde2ccceef958a5b53b4f
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/27653
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
This patch implements SOC-specific code of mt8183 and link the common
code to support SPI bus.
BUG=b:80501386
BRANCH=none
TEST=Boots correctly on Kukui
Signed-off-by: mengqi.zhang <mengqi.zhang@mediatek.com>
Change-Id: I544e850299c74861313c2425721479fe5b91639e
Reviewed-on: https://review.coreboot.org/27498
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Refactor SPI code which will be reused amon similar SOCs.
BUG=b:80501386
BRANCH=none
TEST=Boots correctly on Elm
Change-Id: If5a6c554dc8361e729cf5c464325b97b2bfb7098
Signed-off-by: Tristan Shieh <tristan.shieh@mediatek.com>
Reviewed-on: https://review.coreboot.org/27497
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Since we move mtk_mmu_init() from bootblock to decompressor, we don't
need to build mmu_opertations.c in bootblock and we don't need to
include <soc/mmu_operations.h> in bootblock.c.
BUG=b:80501386
TEST=manually flashed into kukui and boots into romstage.
Change-Id: I58f97ac1705e4dfde5e2d497d9bec33a1d8d17c2
Signed-off-by: Tristan Shieh <tristan.shieh@mediatek.com>
Reviewed-on: https://review.coreboot.org/27655
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
|
|
This function adds support for gpio_configure_pads_with_override
which:
1. Takes as input two GPIO tables -- base config table and override
config table
2. Configures each pad in base config by first checking if there is a
config available for the pad in override config table. If yes, then
uses the one from override config table. Else, uses the base config to
configure the pad.
This is done to allow sharing of GPIO tables across baseboard-variants
for various boards i.e. Each board can have a base config table which
is provided by the baseboard and an optional override config table
that can be provided by a variant to configure certain GPIOs
differently. It is helpful when the variant GPIO diff list is not very
huge compared to the baseboard.
BUG=b:111743717
TEST=Verified that the GPIO config for phaser is same with and without
this change.
Change-Id: I1c5dc72c8368957201ab53d2e8398ff861341a4c
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/27640
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
MT8183 only allows booting from eMMC, so we have to do eMMC emulation
from an external source, for example EC, which makes the size of
bootblock very important.
A fully functional bootblock (that can boot into verstage or romstage)
is about 38000 bytes. If self decompression (CONFIG_COMPRESS_BOOTBLOCK)
is enabled, only 25088 (66%) bytes are needed.
Inspired from crosreview.com/1070018.
BUG=b:80501386
TEST=manually flashed into kukui and boots into romstage.
Change-Id: I7a739866a4ea3bcafe2ff7b9e88d5ed00f3f3e40
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: https://review.coreboot.org/27599
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
As per the ACPI specification, there are two types of power button
devices:
1. Fixed hardware power button
2. Generic hardware power button
Fixed hardware power button is added by the OSPM if POWER_BUTTON flag
is not set in FADT by the BIOS. This device has its programming model
in PM1x_EVT_BLK. All ACPI compliant OSes are expected to add this
power button device by default if the power button FADT flag is not
set.
On the other hand, generic hardware power button can be used by
platforms if fixed register space cannot be used for the power button
device. In order to support this, power button device object with HID
PNP0C0C is expected to be added to ACPI tables. Additionally,
POWER_BUTTON flag should be set to indicate the presence of control
method for power button.
Chrome EC mainboards implemented the generic hardware power button in
a broken manner i.e. power button object with HID PNP0C0C is added to
ACPI however none of the boards set POWER_BUTTON flag in FADT. This
results in Linux kernel adding both fixed hardware power button as
well as generic hardware power button to the list of devices present
on the system. Though this is mostly harmless, it is logically
incorrect and can confuse any userspace utilities scanning the ACPI
devices.
This change gets rid of the generic hardware power button from APL
and relies completely on the fixed hardware power button.
BUG=b:110913245
TEST=Verified that fixed hardware power button still works as expected
on octopus.
Change-Id: I86259465c6cfaf579dd7dc3560b4c9e676b80b55
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/27273
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Logic: If vboot is not used and the tpm is not initialized in the
romstage makes use of the ramstage driver to initialize the TPM
globally without having setup calls in lower SoC level implementations.
* Add TPM driver in ramstage chip init which calls the tpm_setup
function.
* Purge all occurrences of TPM init code and headers.
* Only compile TIS drivers into ramstage except for vboot usage.
* Remove Google Urara/Rotor TPM support because of missing i2c driver
in ramstage.
Change-Id: I7536c9734732aeaa85ccc7916c12eecb9ca26b2e
Signed-off-by: Philipp Deppenwiese <zaolin@das-labor.org>
Reviewed-on: https://review.coreboot.org/24905
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This is how these MSR's are referenced in Intel® 64 and IA-32 Architectures
Software Developer’s Manual.
The purpose is to differentiate with MSR_SMRR_PHYSx.
Change-Id: I54875f3a6d98a28004d5bd3197923862af8f7377
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/27584
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Enable fast or extended DRAM test based on devicetree setting.
The fast DRAM test takes less than a second, while the
extended runs about 1 minute.
Tested on Cavium Soc.
Change-Id: I6a375f3d4c5cea7c3c0cd4592287f3f85dc7d3cf
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/27103
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
|
|
Depends on Change-Id: I0f27b92a5e074966f893399eb401eb97d784850d
Apply additional devicetree fixes:
* Update SCLK from boot fuses
* Updated REFCLKUAA from UART ref clock divider settings
* Remove disabled PEM entries
* Remove phandle to disabled PEM entries
Fixes:
* Linux console wrong baud rate once the PL011 driver is started.
* thunderx-pem kernel module crash on disable PCIe ports.
Tested on Cavium SoC.
Change-Id: I7e8eefd913915a879dad28dfb7801a2018ed2985
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/25382
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
|
|
This patch implements gpio_set_pull() and links the common MediaTek
GPIO code to support IO config for other drivers (ex. SPI) and the
requested functions in src/include/gpio.h.
BUG=b:80501386
BRANCH=none
TEST=Boots correctly on Kukui
Change-Id: Ia2b0d88e9b70c9ad148797d77dc9e79ce1bcb64a
Signed-off-by: Po Xu <jg_poxu@mediatek.com>
Reviewed-on: https://review.coreboot.org/27417
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Refactor GPIO code which will be reused among similar SOCs.
BUG=b:80501386
BRANCH=none
TEST=Boots correctly on Elm
Change-Id: Icdd1f2a1dd1bd64a7218bf9c63bd4a0af1acbcc0
Signed-off-by: Tristan Shieh <tristan.shieh@mediatek.com>
Reviewed-on: https://review.coreboot.org/27416
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
* Add support for secure/unsecure split
* Use MMCONF to access devices in domain0
* Program MSIX vectors to fix a crash in GNU/Linux
Tested on Cavium CN81XX_EVB.
All PCI devices are visible.
Change-Id: I881f38a26a165e6bd965fcd73547473b5e32d4b0
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/25750
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This config is used to provide the name of a region where a microcode
is located. The address of this will be added as the first entry in
the FIT of the topswap bootblock.
This adds a capability to associate two microcodes for each
of the two bootblocks, this allows for the CPU to boot with different
microcodes with 2 separate bootblocks.
Change-Id: I4ee41d90bae34862aa68c9b8bd69288de1335585
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/27151
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Intel PCH/Southbridges have feature that it is possible
to have the southbridge/PCH look for the bootblock at a 64K or
128K/256K/512K/1MB (in case of newer SoCs) offset instead of
the usual top of flash.
Add configs to create a second bootblock and configure its size.
Change-Id: I4bbd19c35871891b762a0673f840858d972e129e
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-on: https://review.coreboot.org/22533
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Put the PCIe clock pins in power-saving mode for the WiFi module to save
power.
Note: This currently does not appear to have any effect on grunt.
BUG=b:110041917
BRANCH=none
TEST=boot without this patch:
$ iotools mem_read32 0xfed80e00
0x0046f3ff
With this patch:
$ iotools mem_read32 0xfed80e00
0x0046f3f1
Change-Id: I389815bc36b8610a30b0cbb9d73262ad392e0181
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-on: https://review.coreboot.org/27465
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
TEST=Boot up with W0 stepping processor.
Change-Id: Ia7bcfd5235e57c70aa3f15d0042da8b16cf7e186
Signed-off-by: Krzysztof Sywula <krzysztof.m.sywula@intel.com>
Reviewed-on: https://review.coreboot.org/27500
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I65f900a3277bc8a4a83ebc8883d4a325bd690bf8
Signed-off-by: Philipp Hug <philipp@hug.cx>
Reviewed-on: https://review.coreboot.org/27438
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Each HART of a SoC like fu540 supports a different ISA. In order for the
coreboot's code can run on each core, need to modify the compile options.
So add this code.
Change-Id: Ie33edc175e612846d4a74f3cbf7520d4145cb68b
Signed-off-by: Xiang Wang <wxjstz@126.com>
Reviewed-on: https://review.coreboot.org/27442
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-by: Philipp Hug <philipp@hug.cx>
|
|
update external processor name to match declaration in SSDT.
in SSDT:
Processor (\_PR.P000, 0x00, 0x00000410, 0x06) {}
Processor (\_PR.P001, 0x01, 0x00000000, 0x00) {}
in DSDT:
External (_PR_.CP00, UnknownObj)
External (_PR_.CP01, UnknownObj)
After fix this, ACPI _PSL (Passive List) now can return correct list
of processor objects for thermal passive cooling.
BUG=b:111478152
BRANCH=master
TEST=emerge-grunt coreboot
Change-Id: I78c838608c78eb7b5e3f8d5c67589e082c756201
Signed-off-by: Kevin Chiu <Kevin.Chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/27495
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
* Use Kconfig options instead of unusable getenv
* Select CAVIUM_BDK_DDR_TUNE_HW_OFFSETS on CN81XX
* Fix Coverity CID 1393976 (DEADCODE)
Tested on Cavium's cn8100_sff_evb.
Change-Id: Ia16c0161b0e9cf5d06418e46556c0fb45532a5b1
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/27448
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
|
|
GPIO functions are required by the Grunt SMI handler.
Change-Id: Id729139b02c10bdd922b3df298f8f9feb1aff745
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/27485
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
The gpio_set function was not writing the correct GPIO register
address.
Change-Id: Ib306773ac72505977b606836bbaf3e2067324894
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/27484
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
