| Age | Commit message (Collapse) | Author |
|---|
|
Change-Id: I6c77f4289b46646872731ef9c20dc115f0cf876d
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/29161
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
The file smbus.asl has 0 bytes (no content). Now that it's no longer included,
remove it.
BUG=b:117814641
TEST=Build grunt and gardenia.
Change-Id: I66389c721e272053d86357f71a6d1242ca767edd
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/29182
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
This change adds new macros to GPIO common library helpers to allow
a GPI pad to be dual routed using PAD_CFG_GPI_DUAL_ROUTE. It also adds
a helper macro to configure a pad for IRQ and wake.
Above macros are guarded using a newly added Kconfig option
SOC_INTEL_COMMON_BLOCK_GPIO_DUAL_ROUTE_SUPPORT that is selected only
by SoCs that have been validated to allow dual route of
GPIs. Currently, this config is selected only for APL/GLK/SKL/KBL that
have been validated to work with dual-routing of GPIs for IRQ and
wake.
BUG=b:117553222
Change-Id: Iaa623d2d78a50f1504e3abe9a47a5a663693aead
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/29188
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change updates various PAD_CFG_GPI* macros to configure Tx as
Disabled in IO Standby state. This is done to ensure that the Tx
setting is same in IO Standby state as it was in active state i.e. Tx
disabled.
BUG=b:17553222
Change-Id: If462aee3884cc61a519fb358b84867c695ace251
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/29199
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Also add a test case for that, a config taken from chromiumos with some
references to binaries dropped that aren't in our blobs repo (eg audio
firmware).
Change-Id: I411c0bacefd9345326f26db4909921dddba28237
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/29223
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Make use of the common CF9 reset in SOC_INTEL_COMMON_RESET. Also
implement board_reset() as a "full reset" (aka. cold reset) as that
is what was used here for hard_reset().
Drop soc_reset_prepare() thereby, as it was only used for APL. Also,
move the global-reset logic.
We leave some comments to remind us that a system_reset() should
be enough, where a full_reset() is called now (to retain current
behaviour) and looks suspicious.
Note, as no global_reset() is implemented for Denverton-NS, we halt
there now instead of issuing a non-global reset. This seems safer;
a non-global reset might result in a reset loop.
Change-Id: I5e7025c3c9ea6ded18e72037412b60a1df31bd53
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/29169
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Add SOUTHBRIDGE_INTEL_COMMON_RESET for all Intel platforms that used to
perform a "system reset" in their hard_reset() implementation. Replace
all duplicate CF9 reset implementations for these platforms.
Change-Id: I8e359b0c4d5a1060edd0940d24c2f78dfed8a590
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/28862
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Add an `amdblocks` internal API and rename
soft_reset() => warm_reset()
hard_reset() => cold_reset()
as these terms are commonly used in the surrounding code.
On Stoney Ridge, make board_reset() call cold_reset() to keep
current behaviour of common code calling hard_reset(). But add
a TODO if this is intended.
Note: Stoney Ridge is using CF9 for the actual reset but the
configuration for a cold reset doesn't use the usual full reset
bit but some other mechanism.
Change-Id: Id33eda676d79529db759b85fa8e28386846e6fa4
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/29053
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
|
|
Change-Id: I2f69d9f01ac5f7e28dd98e704f3280bf62b9ce58
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/29052
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Note, MT8183 didn't select HAVE_HARD_RESET before. So it might still
need an update.
Change-Id: Ic850f2775ada5e6e543ffb92aaa033b9209596f5
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/29051
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Change-Id: If8fc29c46e2cbc69f94ea8b6dc414a93d82ffb28
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/29050
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Change-Id: Id07e1c7fbd35393ffafda53fc7a15ec0e157d075
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/29049
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Change-Id: I6182da172ae2f4107a9b5d8190e4b3b10ed2f0b9
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/29048
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Looks like we've got a race condition between commit ce8763fb with
Change-Id I4e3e715106a1a94381a563dc4a56781c35883c2d ("mb/lowrisc: Remove
the Nexys4DDR port") and commit 2e38dbe5 with Change-Id
I5524732f6eb3841e43afd176644119b03b5e5e27 ("riscv: update mtime
initialization"). Let's fix it.
Change-Id: I03c5860b27d04b6e1d7868ba8ea7b52d1075aa6a
Signed-off-by: Peter Lemenkov <lemenkov@gmail.com>
Reviewed-on: https://review.coreboot.org/29165
Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-by: Philipp Hug <philipp@hug.cx>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch selects common HDA driver and adds audio controller device id
to enable audio on coffee lake platforms.
BUG= None
TEST= boot to yocto linux and windows os on CFL RVP11 & RVP8, verified audio
functionalities.
Change-Id: I4a60a4d7d8babcd0c14664a304ca81d47c668a6c
Signed-off-by: Praveen hodagatta pranesh <praveenx.hodagatta.pranesh@intel.com>
Reviewed-on: https://review.coreboot.org/29145
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add EMI config to initialize memory.
BRANCH=none
TEST=Boots correctly on Kukui, and inits DRAM successfully with related
patches.
Signed-off-by: Huayang Duan <huayang.duan@mediatek.com>
Change-Id: I945181aa1c901fe78ec1f4478a928c600c1b1dea
Reviewed-on: https://review.coreboot.org/28835
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
|
|
Add register definitions of DRAM controller.
BUG=b:80501386
BRANCH=none
TEST=Boots correctly on Kukui
Change-Id: I8b51486deab856a783b87f0b2812a991d4111020
Signed-off-by: Tristan Shieh <tristan.shieh@mediatek.com>
Reviewed-on: https://review.coreboot.org/28668
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
|
|
Phase 1. Due to the size of the effort, this CL is broken into several
phases.
Change-Id: I0236e0960cd1e79558ea50c814e1de2830aa0550
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/29065
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
|
|
Register 0x40 of miscellaneous MMIO is double defined, with different names,
which makes it confusing. Eliminate MISC_MISC_CLK_CNTL_1, and move its only
bit definition to MISC_CLK_CNTL1 (which is correctly placed among MMIO
registers.
BUG=b:117818431
TEST=Build grunt.
Change-Id: I5ca5045498b8a81943282e0d6ecfbaecbd600d19
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/29175
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
SPI100_SPEED_CONFIG is double defined. Bits and shift definitions on the
first definition are unused. Remove first definition and its associated
bits and shifts.
BUG=b:117818430
TEST=Build grunt.
Change-Id: I8175b9a2f379b47475a71f93096f682bc56d051c
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/29172
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
WIDEIO_RANGE_ERROR and TOTAL_WIDEIO_PORTS are defined twice. Remove the
definitions within MMIO definitions, as wideio is not related to MMIO.
BUG=b:117814228
TEST=Build grunt.
Change-Id: I370a5b387b908fe7a840eb7579d45c1a6a9ca615
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/29168
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
The definition DEV_D18F4 is only used once, in file tsc_freq.c, and is
the same as SOC_PM_DEV. Remove the definition, and replace its use in
tsc_freq.c with SOC_PM_DEV.
BUG=b:117754424
TEST=Build and boot grunt.
Change-Id: I9eeeaa084e5b16280713b8b833b4faa78d277586
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/29166
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
GPIO control a mux base addresses are defined within MMIO definitions
and again bellow as GPIO specific base addresses. Eliminate those outside
MMIO bases. Rename them to something indicating that they are both MMIO
and related to GPIO.
BUG=b:117754420
TEST=Build grunt.
Change-Id: I53f7cf17d6267e6f8daa650b5f864bab688dc3f0
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/29156
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
There's no indication that they are accessed through D0F0. Add a D0F0 header
and move IOAPIC definitions under it. The registers defined to be accessed
through index/data pair should be indented relative to the index/data pair
definition.
BUG=b:117754786
TEST=Build grunt.
Change-Id: If4fb6514bb13f1c944d0e1756d8d9de1f08c99f3
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/29155
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
In function smm_setup_structures(), the function name is used in a print
string. Use __func__ instead.
BUG=b:117642170
TEST=Build grunt.
Change-Id: Icac5ea997289ef75fb246a09715cbca4442a57f4
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/29154
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Comparison should place the constant on the right side. Southbridge.c has 6
instances where the opposite happens. Reverse the order of six comparisons
to eliminate checkpatch warnings:
WARNING: Comparisons should place the constant on the right side of the test
BUG=b:117656929
TEST=Build grunt.
Change-Id: I94f17b81f845fa94599f93c0be1144ffcb8e4165
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/29153
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
File smbus_spd.c has 2 instances of if()/else where the if tests for an
error condition and returns just before the "else" statement. These "else"
statements are not needed.
BUG=b:117648025
TEST=Build and boot grunt.
Change-Id: Ie8298773ae455dbb1125420ec65df24f3c65eb44
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/29152
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
src/soc/intel/common/block/pmc/pmclib.c
Function acpi_get_sleep_type: Pointer ps checked for
NULL may be dereferenced.
BRANCH=None
TEST=Built & booted Yorp board.
Change-Id: I15fe39fd9f930be56d03c2ffe62fb6f17249d4b5
Signed-off-by: John Zhao <john.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/29149
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
In Skylake/Kabylake, if ACPI PM timer is disabled then TCO also gets
disabled & vice versa.
FSP default config for EnableTcoTimer is disabled, this caused ACPI PM
timer & TCO to be disabled by FSP even when config PmTimerDisable = 0.
Thus update FSPS UPD EnableTcoTimer in accordance to devicetree config
PmTimerDisable.
BUG=None
TEST= Build for Soraka with PmTimerDisable=0 & check if TCO caused
reboot after running shell command: cat >> /dev/watchdog0
Change-Id: Ia146761036c9dbaef3c02c9a7122ae3dcdef7bdd
Signed-off-by: Naresh G Solanki <naresh.solanki@intel.com>
Reviewed-on: https://review.coreboot.org/29108
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
|
|
- CNL PCH-H has 12 GPIO groups which are grouped under 5 gpio communities.
- Add gpio pin definitions for CNP-H and related changes.
- Add gpio device name, host software ownership reg offset for CNP-H.
BUG: none
TEST: build and flash, boot to windows and yocto os on both CFL RVP8 &
RVP11 and verify power management, IO device functionalities
work fine.
Change-Id: I496ec059de125b97c646581bbd3b8bfe6ffa641e
Signed-off-by: praveen hodagatta pranesh <praveenx.hodagatta.pranesh@intel.com>
Reviewed-on: https://review.coreboot.org/28890
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Cannon lake PCH-H is added to support coffee lake RVP11 and coffee lake
RVP8 platforms.
- Add new device IDs for LPC, PCIE, PMC, I2C, UART, SMBUS, XHCI, P2SB,
SRAM, AUDIO, CSE0, XDCI, SD, MCH and graphics device.
- Add new device IDs to intel common code respectively.
- Add CPU, LPC, GD, MCH entry to report_platform.c to identify RVP11 & RVP8.
- CNL PCH-H supports 24 pcie root ports and 4 I2C controllers, hence chip.c
is modified accordingly.
- Add board type UserBd UPD to BOARD_TYPE_DESKTOP for both RVP11 & RVP8.
BUG=None
TEST=successfully boot both CFL RVP11 & RVP8, verified all the enabled devices
are enumerated and cross checked devices ids in serial logs and UEFI shell.
Change-Id: I4b6af88d467382250aecb4102878b1c5af92ccd4
Signed-off-by: praveen hodagatta pranesh <praveenx.hodagatta.pranesh@intel.com>
Reviewed-on: https://review.coreboot.org/28718
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch implements SoC-specific defines of mt8183 and links the
common code to support USB.
BUG=b:80501386
BRANCH=none
TEST=Boots correctly on Kukui
Change-Id: I1224cf24f92b07f3c1814f1cbfef96aafa5a992b
Signed-off-by: Jumin Li <jumin.li@mediatek.com>
Reviewed-on: https://review.coreboot.org/28787
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Joel Kitching <kitching@google.com>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Refactor USB code which will be reused among similar SoCs.
BUG=b:80501386
BRANCH=none
TEST=Boots correctly on Elm
Change-Id: I06fefb4149a489be991e13ddf624082d11e31765
Signed-off-by: Tristan Shieh <tristan.shieh@mediatek.com>
Reviewed-on: https://review.coreboot.org/28786
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Change-Id: I85f357739220f16497f65df1bb317d9d6eb54d9f
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/29046
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
Make #define definitions for PMxEF and replace the hardcoded values.
Note that this doesn't change the current functionality of the source.
The existing code has been propogated from the sb//hudson port, which
seems to attempt to enable 100% of all OHCI and EHCI controllers that
may be present in the system.
Change-Id: I6018b0062730de19e3283a010144dfedc2b11423
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/29075
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Remove nonpreset controllers from the PCI device identifier function
(ignoring any CONFIG_USBDEBUG_HCD_INDEX). The extra devices appear
to be holdovers from the original sb/hudson source.
TEST=Jam Makefile.inc to unconditionally build enable_usbdebug.c and
verify proper BDF is returned in romstage and ramstage.
Change-Id: I2e819d5e998922ad427c4a094c29a590f249a0d3
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/29074
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Delete an unmatched opening parenthesis in the definition for the EHCI
hub config register definition. This wasn't causing a problem unless
EHCI debug was enabled.
TEST=Jam Makefile.inc to unconditionally build enable_usbdebug.c and
verify successful build
Change-Id: I5f461d1573e416b5a8ee24329142e3c46b6a05e3
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/29073
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Move the SPI base address register definition to D14F3. This was
missed in:
bba043 amd/stoneyridge: Rearrange southbridge.h
Change-Id: Ia722339418c118bdf4b000bbf97ae4266e9b3be2
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/29072
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
With https://github.com/IntelFsp/FSP/pull/4 merged, this allows using
Intel's FSP repo (that we mirror) to build a complete BIOS ifd region
with a simple coreboot build, automatically drawing in headers and
binaries.
This commit covers Apollolake, Coffeelake, Skylake, and Kabylake.
Skylake is using Kabylake's FSP since its own is FSP 1.1 and Kabylake's
also supports Skylake.
Another candidate (given 3rdparty/fsp's content) is Denverton NS, but
it requires changes to coreboot's FSP bindings to become compatible.
Cannonlake, Whiskeylake require an FSP release.
Change-Id: I8d838ca6555348ce877f54e95907e9fdf6b9f2e7
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/28593
Reviewed-by: Pratikkumar V Prajapati <pratikkumar.v.prajapati@intel.com>
Reviewed-by: Naresh Solanki <naresh.solanki@intel.com>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The AMD implementation of this register is only 16 bits. Change the
source accordingly.
TEST=Suspend/Resume a Grunt several times
Change-Id: Ib900468cc1c790fa7d57bb6faa91aee012173f7a
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/29016
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
|
|
Shorten the names in the MISC CGPLL_CONFIG, and make the formatting match
the surrounding source.
Change-Id: I71cf1ff6bd4bca7a25484b4da9388c17cfecc043
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/29015
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
|
|
Make the field names of the MISCx00 GPPClkCntrl more manageable by
shortening their names. Make the definitions look more like the
rest of the header file.
Change-Id: I515cd664808e38851a7dbdba899df4fb9bbbcde6
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/29014
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
|
|
Group definitions so they're near others of the same type, e.g. PCI,
AcpiMmio, etc.
Change-Id: Ia6ef21431db0e758eba0ea043b54c036ec6235fe
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/29013
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
|
|
Delete definitions that are no longer used.
Change-Id: I94c9c33f73c1a2d9308408e3e9ca526e876d6135
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/29012
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
|
|
Change-Id: I1b44ffd7c0244b0408c3823d634a9b8d5038462f
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/29011
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
|
|
Make the whitespace match surrounding lines and remove unnecessary
parentheses.
Change-Id: I2ed02494ba69237c38af61317e435d9575cefe1c
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/29010
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
|
|
Match the rest of the soc/stoneyridge source.
Change-Id: I4531e6dad0362be73499647d9fc93c168b6f163e
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/29009
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
|
|
Delete artifacts remaining from the original "hudson" and "yangtze"
controller hub designs.
Husdon devices had a configurable AcpiMmio base address, and a selection
for I/O vs. MMIO decode. Modern products are fixed at 0xfed80000 in MMIO.
Remove the flash control register definitions for the old generations.
The manual reset register appears to not function as hudson.
PMIO_DEBUG is named differently now, and not used, so remove its
definition too.
Change-Id: I6484bb2ca80b65318565dfee1a3368b121aea9de
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/29008
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
|
|
Use "cpu/x86/msr.h" for common IA-32 MSRs and correct IA-32 MSRs names.
Change-Id: Ida7f2d608c55796abf9452f190a58802e498302d
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/28752
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-by: Pratikkumar V Prajapati <pratikkumar.v.prajapati@intel.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I849dd406f5ccc733d4957eaf1c774745782f531a
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/28784
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
STAPM devicetree registers do not indicate the unit, which causes confusion.
More importantly, the time was assumed to be in seconds when it's actually
milliseconds. This caused early STAPM configurations to fail.
BUG=b:117590953
TEST=Build grunt
Change-Id: I2a7e3d43601992d1f7b02456913c763d940fe9ee
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/29035
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Bounce buffers used to be used in those cases where the payload
might overlap coreboot.
Bounce buffers are a problem for rampayloads as they need malloc.
They are also an artifact of our x86 past before we had relocatable
ramstage; only x86, out of the 5 architectures we support, needs them;
currently they only seem to matter on the following chipsets:
src/northbridge/amd/amdfam10/Kconfig
src/northbridge/amd/lx/Kconfig
src/northbridge/via/vx900/Kconfig
src/soc/intel/fsp_baytrail/Kconfig
src/soc/intel/fsp_broadwell_de/Kconfig
The first three are obsolete or at least could be changed
to avoid the need to have bounce buffers.
The last two should change to no longer need them.
In any event they can be fixed or pegged to a release which supports
them.
For these five chipsets we change CONFIG_RAMBASE from 0x100000 (the
value needed in 1999 for the 32-bit Linux kernel, the original ramstage)
to 0xe00000 (14 Mib) which will put the non-relocatable x86
ramstage out of the way of any reasonable payload until we can
get rid of it for good.
14 MiB was chosen after some discussion, but it does fit well:
o Fits in the 16 MiB cacheable range coreboot sets up by default
o Most small payloads are well under 14 MiB (even kernels!)
o Most large payloads get loaded at 16 MiB (especially kernels!)
With this change in place coreboot correctly still loads a bzImage payload.
Werner reports that the 0xe00000 setting works on his broadwell systems.
Change-Id: I602feb32f35e8af1d0dc4ea9f25464872c9b824c
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: https://review.coreboot.org/28647
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Fixes builds of that binary in clean trees.
Change-Id: If5a995449a74c00da836fcf22bda44ebc8197518
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/28994
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Remove assert() and instead use if statement to check if
comm->groups is NULL.
Found-by: klockwork
BUG=None
TEST=Boot to OS
Change-Id: I85a6bc700b52d04c61ca8f2baac62000f40cf2cb
Signed-off-by: Bora Guvendik <bora.guvendik@intel.com>
Reviewed-on: https://review.coreboot.org/28940
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This change sets PCIEXPWAK_DIS in PM1_EN register if WAKE# pin is not
enabled on the platform. This is required to prevent unnecessary wakes
if the WAKE# pin remains not connected on the platform. Function to
set PCIEXPWAK_DIS gets called in normal boot path (BS_PAYLOAD_LOAD) as
well as S3 resume path (BS_OS_RESUME).
BUG=b:117284700
TEST=Verified that no spurious wakes are observed on nocturne.
Change-Id: Iea93baffc9bb703c0ffedacafc6a9a9410c7ebfe
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/28939
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
|
|
Now only those UARTs that are enabled in devicetree.cb are initialized.
Tested on Opencellular Elgon.
Change-Id: I145c224148f0cc078bb1c76f588f603e73121a62
Signed-off-by: Jens Drenhaus <jens.drenhaus@9elements.com>
Reviewed-on: https://review.coreboot.org/28975
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
AMD's SOC do not wait for I2C transactions to complete before executing
a reset. Because of this, it's possible for the reset to happen in the
middle of a transaction, resulting on a slave hang. There are 2 possible
solutions:
If the slave has a reset pin connected to a GPIO pin, it can be used to
reset the slave, else the only solution is to bang SCL 9 times. Create
code that makes it easy to implement SCL bang, using a devicetree
register to define which I2C SCL lines needs to be reset.
BUG=b:114479395
TEST=Build and boot grunt. Look at transactions on a scope.
Change-Id: I7f74b7e45c509044825355874753969f074e2382
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/28574
Reviewed-by: Daniel Kurtz <djkurtz@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Set up DRAM related PLLs.
And update post divider table to fulfill all freqency settings.
BUG=b:80501386
BRANCH=none
TEST=Boots correctly on Kukui
Change-Id: Ic197cef7d31f75ffe4e7d9e73c9cc544719943ab
Signed-off-by: Tristan Shieh <tristan.shieh@mediatek.com>
Signed-off-by: Weiyi Lu <weiyi.lu@mediatek.com>
Reviewed-on: https://review.coreboot.org/28667
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Joel Kitching <kitching@google.com>
|
|
This patch creates _PRT entires for each PCIE root port devices.
TEST=Able to see PCIE wake device in cat /proc/acpi/wake list
Change-Id: I183c89c92139e15e0bfc39620710dbdc6597b351
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/28800
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This patch provides option for PCI IRQ mapping in both PIC and APIC mode.
TEST=Build and Boot on CNL RVP.
Change-Id: Ie26750ac9dc2ce940b0c116085c041de439075df
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/28799
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
issue
This patch fixes below ACPI compilation issue:
Found 1 external control methods, reparsing with new information
Pass 1 parse of [DSDT]
ACPI Error: [EPCS] Namespace lookup failure, AE_ALREADY_EXISTS (20160318/dsfield-660)
ACPI Error: [EMNA] Namespace lookup failure, AE_ALREADY_EXISTS (20160318/dsfield-660)
ACPI Error: [ELNG] Namespace lookup failure, AE_ALREADY_EXISTS (20160318/dsfield-660)
Pass 2 parse of [DSDT]
ACPI Warning: NsLookup: Type mismatch on EPCS (Integer), searching for (RegionField) (20160318/nsaccess-664)
ACPI Warning: NsLookup: Type mismatch on EMNA (Integer), searching for (RegionField) (20160318/nsaccess-664)
ACPI Warning: NsLookup: Type mismatch on ELNG (Integer), searching for (RegionField) (20160318/nsaccess-664)
Parsing Deferred Opcodes (Methods/Buffers/Packages/Regions)
TEST=Able to build sgx.asl without any ASL error.
Change-Id: If4e7d4c66b6aab6c081fa272d8c2c9a1f0651ef7
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/28961
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This patch to fix KW issue due to msg, data and response pointers NULL
check fail.
Change-Id: I39324514079f240ba1683a04e579de85485299bf
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/28949
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Legacy PME are enabled by default in FSP-S UPD. This policy sets
PME Interrupt Enable (PIE) bit of RCTL register to trigger interrupt
generation when RSTS.PS state has changed (either due to 0->1 transition
or due to this bit being set with RSTS.PS already set). Due to this
interrupt generation, system wakes from sleep immediately it enters.
This patch overrides root port legacy pme upd policy from coreboot to
ensure no false SCI is triggerd when system is in S3/S0ix state.
BUG=b:113083354
BRANCH=none
TEST=Able to make S3 resume using wake on wifi connect/disconnect usecase
without any failure.
Change-Id: I779fac711eeeed65ea379fad1cc400052d8a00eb
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/28947
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This patch save and restore ITSS IPCx register before and after
FSP-S call.
Change-Id: Iea9356b4404d2fa49ea62ef7bc2c72f125054ff3
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/28792
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch save and restore ITSS IPCx register before and after
FSP-S call.
Change-Id: Ib731f27826d604c305dc52a8488fd6240b01148a
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/28791
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This patch selects Kconfig for Intel Core Platform in order to ensure
proper ITSS IPCx programming.
Change-Id: I81e75e17ceb23c364b78300c3950144be1580700
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/28790
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Its spreading copies got out of sync. And as it is not a standard header
but used in commonlib code, it belongs into commonlib. While we are at
it, always include it via GCC's `-include` switch.
Some Windows and BSD quirk handling went into the util copies. We always
guard from redefinitions now to prevent further issues.
Change-Id: I850414e6db1d799dce71ff2dc044e6a000ad2552
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/28927
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This patch fixes KW issue due to pointer being NULL and will be dereferenced
Change-Id: Iedb59daf5f448e31c0097873a086e4d08cd4a979
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/28948
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
It exposes an interface that is as generic as possible, so payloads
and/or kernels can use it for their data.
Change-Id: I9553922f9dfa60b9d4b3576973ad4b84d3fe2fb5
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/25182
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I6b40aaf5af5d114bbb0cd227dfd50b0ee19eebba
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/28934
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
In order to make the macro name consistent for all PAD_CFG1_IOSSTATE_*
macros, this change uses lower case x for *RXD*. It helps avoid
confusion when using the macros.
Change-Id: I6b1ce259ed184bcf8224dff334fcf0a0289f1788
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/28924
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change sets scan_bus operation for HDA to scan_static_bus to
allow enumeration of static devices under HDA.
BUG=b:112888584
TEST=Verified that devices added under HDA get enumerated on Nocturne.
Change-Id: I20759c2b702b2f107f0913e7ce92a82c6070ddc4
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/28807
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Config option SOC_INTEL_COMMON_BLOCK_HDA is currently used for
initialization of HDA codecs only. This prevents adding of any static
devices under the HDA device node. However, there can be boards which
want to add devices under HDA node (e.g. nocturne that wants to
provide DMIC properties to OS) without performing any codec
initialization using the HDA. This change:
1. Adds a new config option SOC_INTEL_COMMON_BLOCK_HDA_VERB that can
be set explicitly by the boards that want to perform codec
initialization.
2. Uses newly added config option is used to guard the initialization
functions for the codec. Rest of the device operations can still be
used by all the other boards without having to use HDA codec
initialization.
3. Selects the newly added option SOC_INTEL_COMMON_BLOCK_HDA_VERB in
kblrvp which is the only board enabling HDA codec initialization
using common block code.
4. Selects original config SOC_INTEL_COMMON_BLOCK_HDA for skylake SoC.
Above changes need to be bundled and pushed in as a single change in
order to avoid breaking existing users.
BUG=b:112888584
Change-Id: Ie6f39c13a801833b283120a2d4b6f6175688999c
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/28806
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
This patch removes assert() and checks if the dev is NULL with "if"
condition only.
Found-by: klockwork
Change-Id: Icd2c8490c8bda14ecd752437d463a7110fe40aea
Signed-off-by: Pratik Prajapati <pratikkumar.v.prajapati@intel.com>
Reviewed-on: https://review.coreboot.org/28888
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I492224b6900b9658d54c8cf486ef5d64b299687f
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/28871
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
|
|
TEST=Build Grunt
BUG=b:77602074
Change-Id: I24a46cc3e766ba7e9199723b042476064a698bf2
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/28865
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Remove AcpiMmio and PCI config registers that are not used.
TEST=build Grunt
BUG=b:77602074
Change-Id: I62f40e421eba41c4a49d85efc975096171cb72fa
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/28864
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Remove the step of setting the SATA controller to S0 as the system is
entering S3. This had been duplicated from AMD's FchCarrizo.asl file,
but upon closer inspection, the conditions for this step to run cannot
be met. This does not affect Grunt's behavior, as the SATA controller
is disabled.
TEST=Suspend and resume Grunt
BUG=b:77602074
Change-Id: Ib269a5363d03c7048abd0c8a9a28df92a773790c
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/28863
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Move funtions callbacks used to override FSP upd values to
separate files. This serves as a base change for SoCs for which
FSP is still under development, and hence the FSP header files
are not available yet and in turn the UPDs cannot be referred.
These newer SoCs will implement empty callbacks. The code will
compile with basic header files which only include the architectural
FSP structures.
This allows plugging in these separate files for compilation in an
environment where FSP header files are available.
The fact is, FSP header files are not released externally until PRQ.
However the teams at intel and some partners have access to the development
version of these files. This code refactor helps to continue development
on the pre-PRQ silicons and submit related code to coreboot.org.
BUG=None
BRANCH=None
TEST=Build for cnlrvp
Change-Id: Iffadc57f6986e688aa1bbe4e5444d105386ad92e
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/28661
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Increase bootblock size by 4KiB and reduce romstage by 4 KiB.
Change-Id: I604fd9c63a4cf6fb7b18249a6d73cd637e184a71
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/28875
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Change-Id: I3f4123657a375211f802a7d484a15353f9a256e9
Signed-off-by: Bora Guvendik <bora.guvendik@intel.com>
Reviewed-on: https://review.coreboot.org/28795
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hannah Williams <hannah.williams@intel.com>
|
|
Use BIOS_DEBUG consistently to log PM1 and PMxC0 status registers
on boot. print_num_status_bits() was already using BIOS_DEBUG.
TEST=Inspect console for Grunt
BUG=b:110788201
Change-Id: If7da8c7c86e90a661338903ad05cc41e11f507d2
Signed-off-by: Edward Hill <ecgh@chromium.org>
Reviewed-on: https://review.coreboot.org/28885
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Implement the function vboot_platform_prepare_reboot() which is normally
a weak function.
The SlpTyp field of the PM1 register is not reset to its default value
when the APU restarts. This change prevents a failing condition if
vboot decides to reset the system instead of allowing an S3 resume to
continue.
TEST=Resume Grunt when vboot attempts a reset, verify a fresh boot instead
BUG=b:117089826
Change-Id: I6e0e3e541bad89ca5b23d6ddb6e5c0df7f762f10
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/28877
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: Id4f99e82bb97a260d654b49a2ba94fde207d318b
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/28847
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable the IOMMU in AGESA and copy the AGESA generated IVRS ACPI table.
BUG=b:116196614
TEST=Check dmesg for AMD-Vi messages.
Change-Id: I688d867c7bd4949a57b27c1b6a793c6a6e4a717a
Signed-off-by: Marc Jones <marc.jones@scarletltd.com>
Reviewed-on: https://review.coreboot.org/28753
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
This patch ensures I2C controllers are out of reset without any
assumptions.
BUG=b:116191230
BRANCH=none
TEST=Dump MMIO offset 0x204 to check if I2C host controller is NOT
at reset (by reading Bit 0-1 as 3)
Change-Id: I4b335a834333e01cfa2d802e4aad0735d0212dcc
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/28762
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
`HMRFPO` was spelled as `HMRPFO` twice.
Change-Id: Ibd04004ac5edcdeee49a6a69fcdd5c73603e92e2
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/28848
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Make correct spelling for THERMAL_IRQ macro in irq.h file.
Change-Id: I83593822e2abbb07e60fc336b774199fea3b368f
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/28802
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
|
|
This patch unified line indentation.
Change-Id: Ife3396e36a0684490d9ed9b31b4c0a543a3e3d24
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/28801
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
|
|
Add methods, and call them, for transitioning EHCI and xHCI to D0 or
D3cold. Add device objects necessary for waking the system via USB.
In order for USB to wake the system, it must be in the D3cold state.
Then on resume, its firmware must be reloaded.
This code relies heavily on AMD's FchCarrizo.asl (delivered in NDA PI
package), and has been modified to fit the coreboot ASL names. In
addition, AMD's methodology is to generate a SW SMI for saving/restoring
certain settings. This has been ported into U3D0 and U3D3, as the
necessary registers are now publicly documented.
BUG=b:77602074
Change-Id: I83d0dce13411601691318cc67c99adf291ccf3bb
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/28772
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add a method to assist with setting the PwrGood Control register, which
will be useful for various devices.
BUG=b:77602074
Change-Id: Ief602c4bc42d27b3e236d24db815b990f3a2419c
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/28771
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Add methods that can be used for preparing all controller hub devices
for sleep, and that will turn the devices back on.
BUG=b:77602074
Change-Id: I4b0c48e96aff23b4c31c9e89582b9fa80dba7bda
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/28770
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Duplicate ASL from AMD's FchCarrizo.asl (available in NDA PI package)
that can put AOAC devices into D0 or D3cold. The argument numbers
coincide with the AOAC register offsets for the various devices.
SATA, USB, and SD require additional device configuration. Add a
placeholder and mark as todo.
BUG=b:77602074
Change-Id: I32426f744a5ebbad9e8d3f2f37c4d214ad6dd3d4
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/28769
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Define various AMD_SB_ACPI_MMIO_ADDR registers at 0xfed80000. Define
various PCI config space registers. These are duplicated from AMD's
FchCarrizo.asl file.
BUG=b:77602074
Change-Id: Ie7447fef682424b05fa912b60c7b80112c6202de
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/28768
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Indicate the devices that are enabled. This is somewhat rudimentary, but
could be improved in a later patch (e.g. get settings from devicetree).
Calculate values that may be used for reinitializing the xHCI firmware.
Add the EHCI BAR's current base address to gnvs.
BUG=b:77602074
Change-Id: I8af69c030eb2353ad75beeb2bfd3bef24abff04c
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/28767
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
A later patch will rely on two USB settings from the BIOS. Add these
to the global_gnvs_t structure.
The first is a data that will be used to locate the xHCI firmware for
reloading after a resume. Although the existing calculations will be
somewhat simple, keeping this on the coreboot side will help in the
event multiple FWs are eventually in the build.
The second item is a usable EHCI base address that may be programmed
during S3 suspend and resume. At the time the PTS and WAK code runs,
the BAR will be clear.
BUG=b:77602074
Change-Id: I32205ac8a6908cca4a38dd68a7c7b591e76c06bb
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/28766
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
A later patch will leverage AMD's ASL support for handling AOAC
devices. This will gather coreboot's device enables from a bitwise field,
where each bit corresponds to the register offset used to control
each devices.
Create an identical structure, and add it to the nvs ASL and global_nvs_t
structure.
BUG=b:77602074
Change-Id: I40f0161cc0bbc574ad703e34278372f2504de100
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/28765
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
|
|
Regarding the SDMs, IA32_MC0_STATUS register is at 0x401, and
IA32_MC0_CTL is at 0x400.
So replace MSR at (0x400+1) by IA32_MC0_STATUS and the one at
0x400 by IA32_MC0_CTL.
Change-Id: I3f53c80f39078bd0c47c25013657e1169fc6c4a6
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/28751
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
Change-Id: I07c95b9ea14d47da0497470487fa3f162f8012c8
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/28789
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
|
|
The globalnvs.asl file had become mixed with tabs and spaces to align
columns. Use all tabs to align the comments.
BUG=b:BUG=b:77602074
Change-Id: Ife4cf86372a8e24e78b38cca0254dd9fa00dd6b0
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/28764
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-by: Martin Roth <martinroth@google.com>
|
