Age | Commit message (Collapse) | Author |
|
Make IGD disable when mainboard user selects SOC_INTEL_DISABLE_IGD.
TEST=Able to get depthcharge pre-OS splash screen with AMD Radeon RX
5700 PCI-E DGPU when mainboard user selects SOC_INTEL_DISABLE_IGD.
Change-Id: Ibbe9c8c4d77018de83815d7d203284b1fbc0da58
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49291
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
This SOC_INTEL_DISABLE_IGD Kconfig will allow to skip IGD
initialization using FSP GOP and eventually disable the IGD.
TEST=Able to get depthcharge pre-OS splash screen when mainboard
user selects SOC_INTEL_DISABLE_IGD with below HW/FW/SW
configuration:
HW: ADLRVP + AMD Radeon RX 5700 PCI-E DGPU
FW: coreboot with depthcharge as payload for ADLRVP and OpRom for
AMD PCI-E DGPU
SW: Chrome OS RC10 release
Change-Id: I465541cb45c9022d53a5beb3fff1f80660c357c9
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49470
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
This adds interrupt handlers that end up calling x86_exception().
Change-Id: I3dce539b6f1ef300cf16f20224744a75100f60b8
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49726
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Picasso doesn't have any EHCI controllers, so it can't support EHCI
debug, so there is no need to specify a MMIO address for the early EHCI
BAR configuration.
Change-Id: I5e904c160c68805a8606a8b2d1ab4fb6172066e7
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49729
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
Picasso doesn't have any EHCI controllers, so it can't support EHCI
debug.
Change-Id: I2dae22c0db294f5334d9796d90f432d6c8d304df
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49685
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
Change-Id: I28be6091097f713472d5ca3b8b0921ee71238cf0
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49589
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
|
|
The code for setting the LPC generic memory range uses an array of fixed
address ranges not needing explicit decoding, to decide if the address
needs to be written to the LGMR register. Most platforms only mistakenly
add the PCH reserved mmio range, that is not decoded generally,
effectively breaking the mechanism. Only APL uses the array correctly.
That code, in it's current state, does not work (except for APL) and
currently, there is not a single user. Thus, drop it before people start
using it.
Change-Id: I723415fedd1b1d95c502badf7b0510a1338b11ac
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49588
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Change-Id: Ied235972d24276d7c88a2f50f192d69d24ae6e05
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45816
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
We need to write some special values to key protection registers before
applying init_setting table and lp_setting table to PMIC. Otherwise,
those settings won't take effect.
After applying init_setting table and lp_setting table, we lock the
settings by writing zero to key protection registers.
Reference datasheet: MT6359_PMIC_Data_Sheet_V1.5.docx, RH-D-2018-0205.
BUG=b:172636735
BRANCH=none
TEST=boot asurada correctly
Signed-off-by: Hsin-Hsiung Wang <hsin-hsiung.wang@mediatek.com>
Change-Id: I593d4e02bf0b62ac297957caf4ae1c1837f1f38d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48954
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
Add scp voltage initialization.
BUG=none
BRANCH=none
TEST=boot asurada correctly
Signed-off-by: Hsin-Hsiung Wang <hsin-hsiung.wang@mediatek.com>
Change-Id: I68302715ae804fed11bb54f4dfc4e90cde5224df
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49355
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
Only amd/picasso and amd/stoneyridge have reference to
PCNT and that could be replaced with acpigen.
Remove the PCNT name from GNVS OperationRegion elsewhere.
Change-Id: I7dd45a840b3585fd24c31fd923b991c34ab4d783
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49272
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Change-Id: Ia27bc256376c61a7330196a5b4a331dd79386fb6
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49472
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Change-Id: I673f038b4ce3c4141db128a65be71e7a242dfd28
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48856
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Struct will be synced with picasso with followups.
Change-Id: I5f460cc3849bf1fad1f6da61169893488ccb2b40
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48855
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The SoC code has in implicit dependency on this option, so select it in
the SoC code instead of the mainboard code.
Change-Id: Iea908c142f4a94a107cf74a31d9f5e29668d4b5b
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49667
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
- Return the busno based on the stack number.
- Replace pci_mmio_read_config32 with pci_io_read_config32 to get the
register value before mapping the MMIOCFG space.
- Remove the plural `s` as the function now provides one bus number.
Change-Id: I6e78e31b8ab89b1bdcfdeffae2e193e698385186
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49457
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lance Zhao
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Change-Id: I461012b164bbd6f2d1162a793903aafe0b15e234
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49564
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
|
|
Change-Id: I3fb4db3fbb72d1444c84b9b66193c26a07561a3f
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49565
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
|
|
Update the settings of long press shutdown to avoid rtc alarm boot.
BUG=b:174546890
BRANCH=none
TEST=boot asurada correctly
Signed-off-by: Hsin-Hsiung Wang <hsin-hsiung.wang@mediatek.com>
Change-Id: I0841e55674f6b26f355ab678a73d4060fe93f27c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49354
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Nicolas Boichat <drinkcat@chromium.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
We found that the switch frequency of vgpu is at 4~5Mhz with high
current case (> 3.5A) and is at 2.5Mhz with low current case(< 2.8A).
The switch frequency of vgpu should be kept at 2.5Mhz.
The root cause is that phase config of vcore is not disabled, it will
affect the switch frequency of vgpu. Corret the phase setting at
initialization.
BUG=b:172636735
BRANCH=none
TEST=boot asurada correctly
Signed-off-by: Hsin-Hsiung Wang <hsin-hsiung.wang@mediatek.com>
Change-Id: I48d3729302de9e3343dce79fe6f5ed045d0296a5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49005
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add clkbuf and srclken_rc init for low power.
Reference datasheet:
Document No: RH-D-2018-0205.
TEST=boot asurada
Signed-off-by: Ran Bi <ran.bi@mediatek.com>
Change-Id: I947bf14df7a307bf359c590c2a20265882b3f1be
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46878
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
Signed-off-by: Huayang Duan <huayang.duan@mediatek.com>
Change-Id: Icfd0923d4bd34ebb082e00e87f262b0d908fe342
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44714
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
Signed-off-by: Huayang Duan <huayang.duan@mediatek.com>
Change-Id: I10e704868e4cd36a938a669879bb1a8632e73e1a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44713
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
After calibration, we can get ddr vendor id or density info from
MR5 or MR8, this helps to make sure the DDR HW is as we expected.
Signed-off-by: Huayang Duan <huayang.duan@mediatek.com>
Change-Id: Ie62948368716d309aab8149372b2b6093fc33552
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44712
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
The layout of GNVS has expectation for a fixed size
array for chromeos_acpi_t. This allows us to reduce
the exposure of <chromeos/gnvs.h>.
If chromeos_acpi_t was the last entry in struct global_nvs
padding at the end is also removed.
If device_nvs_t exists, place a properly sized reserve for
chromeos_acpi_t in the middle.
Allocation from cbmem is adjusted such that it matches exactly
the OperationRegion size defined inside the ASL.
Change-Id: If234075e11335ce958ce136dd3fe162f7e5afdf7
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48788
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Change-Id: I96b302f5a1f10daaed017a2453d1568a2e49e4ad
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49558
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Change-Id: I2ac1035585b32ba65d0725067cff0c12c9f748c1
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49570
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Change-Id: Icf4247a0a5fb7950c69c8f229a6629a4fa6980f7
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49569
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Change-Id: I38974b532f41830f49b54444d98e6bd7aa417aba
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49533
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jacob Garber <jgarber1@ualberta.ca>
|
|
Change-Id: I3aec07d782e4315120a4365a65bdbcbf4a22e6f2
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49521
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jacob Garber <jgarber1@ualberta.ca>
|
|
Change-Id: I646583f7f0d0e0f6a91bc99b7edda964337d837e
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49520
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jacob Garber <jgarber1@ualberta.ca>
|
|
Change-Id: Icc4954bcc1540f1935b0e34107febb4a1e947a36
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49519
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jacob Garber <jgarber1@ualberta.ca>
|
|
Change-Id: Id5bf9255e9a16a4f311e3b15eb77ad6e4bb13f66
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49518
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jacob Garber <jgarber1@ualberta.ca>
|
|
Change-Id: I0018ea16f304a0d2cedfbd55525ecabbf2d89aa1
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49517
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jacob Garber <jgarber1@ualberta.ca>
|
|
Change-Id: Iea0c973b2bd493eb69ef76289b5b4fc66ac622f6
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49516
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jacob Garber <jgarber1@ualberta.ca>
|
|
Change-Id: Ifeac919ac7214c1baf877a36fd3d57636fc83563
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49527
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
According ADL EDS to update the PCH and CPU PCIe RP table.
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: Idcc21d8028f51a221d639440db4cf5a4e095c632
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49021
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
L1_substates_control is common define. Move out of soc level.
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I54574b606985e82d00beb1a61cce3097580366a4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49295
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
In case of CPU PCIe RPs, the RP numbers might not be contiguous for
all the functions in a slot.
Example: In ADL, RP1 is 00:06.0, RP2 is 00:01.0 and RP3 is 00:06.2 as
per the FSP expectations.
Hence, this change updates the defintion of `struct pcie_rp_group` to
include a `start` member which indicates the starting PCI function
number within the group. All common functions for PCIe RP are
accordingly updated to take the `start` member into account.
Thus, in the above example, ADL can provide a cpu_rp_table as follows:
{
{ .slot = PCIE_SLOT_6, .start = 0, .count = 1 },
{ .slot = PCIE_SLOT_1, .start = 0, .count = 1 },
{ .slot = PCIE_SLOT_6, .start = 2, .count = 1 },
}
Since start defaults to 0 when uninitialized, current PCH RP group
tables don't need to be updated.
Change-Id: Idf80a0f29e7c315105f76a7460c8e1e8f9a10d25
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49370
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Having some symmetry with <soc/nvs.h> now allows to reduce
the amount of gluelogic to determine the size and cbmc field
of struct global_nvs.
Since GNVS creation is now controlled by ACPI_SOC_NVS,
drivers/amd/agesa/nvs.c becomes obsolete and soc/amd/cezanne
cannot have this selected until <soc/nvs.h> exists.
Change-Id: Ia9ec853ff7f5e7908f7e8fc179ac27d0da08e19d
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49344
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Lance Zhao
|
|
They all operate on that file, so just add it globally.
Change-Id: I953975a4078d0f4a5ec0b6248f0dcedada69afb2
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49380
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Now that intermediate coreboot.pre manipulation is serialized within
the build system, remove the flock calls.
Change-Id: I8a767918aec5fcb7127ebb19ac46e58bed7967fb
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49381
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
1. Add emi setting to support byte mode and single rank ddr sample
2. Modify initial setting for DDR with different architecture
BUG=b:165768895
BRANCH=kukui
TEST=DDR boot up correctly on Kukui
Signed-off-by: Shaoming Chen <shaoming.chen@mediatek.corp-partner.google.com>
Change-Id: Id2845b2b60e2c447486ee25259dc6a05a0bb619b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48300
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
Add code to collect all required information and generate ACPI CRAT
table entries. Publish tables generated from cb, rather than use the
tables created by FSP binary.
BUG=b:155307433
TEST=Boot trembyle and compare coreboot generated tables with tables
that FSP published previously.
BRANCH=Zork
Change-Id: If64fd624597b2ced014ba7f0332a6a48143c0e8c
Signed-off-by: Jason Glenesk <jason.glenesk@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47727
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Exit early if the chipset power state info isn't in CBMEM. Return -1 in
order to ensure the one caller of this function exits early as well.
Found-by: Coverity CID 1442304
Change-Id: Ifa42ba3024d3144de486d90ed7752820482549bf
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49359
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Lance Zhao
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change affects Intel CPUs only. As most platforms are doing
uCode update using FIT, they aren't affected by this code either.
Update microcode in MP-init using a single spinlock when running on
a Hyper-Threading enabled CPU on pre FIT platforms.
This will slow down the MP-init boot flow.
Intel SDM and various BWGs specify to use a semaphore to update
microcode on one thread per core on Hyper-Threading enabled CPUs.
Due to this complex code would be necessary to determine the core #ID,
initializing and picking the right semaphore out of CONFIG_MAX_CPUS / 2.
Instead use the existing global spinlock already present in MPinit code.
Assuming that only pre-FIT platforms with Hyper-Threading enabled and at
most 8 threads will ever run into this condition, the boot delay is
negligible.
This change is a counterproposal to the previous published patch series
being much more unsophisticated.
Change-Id: I27bf5177859c12e92d6ce7a2966c965d7262b472
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49303
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
This struct isn't used anywhere else, so there's no need to name it.
Change-Id: I22eda07f14096d2b7400e6ab715641ffd68fbc08
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reported-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49444
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
As a requirement of TCSS this setting needs to be correctly set
to determine what Type-C ports are enabled on the platform. Without
this value correctly set there can be adverse effects on the other
TCSS specific values.
BUG=b:159151238
BRANCH=firmware-volteer-13672.B
TEST=Built image for Voxel and verified that S0ix cycles no longer
fail when the IomPortPad is set to 0
Change-Id: I6c5260cda71041439fe89d15bd3cafd4052ef1e7
Signed-off-by: Brandon Breitenstein <brandon.breitenstein@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48813
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
|
|
These are no longer really useful. We can also enable Power Resource
ACPI debug in the kernel if we want these messages.
BUG=none
BRANCH=zork
TEST=emerge-zork and verify debug messages are no longer posted
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I936e816266825f1c59377c2e079ffe1a5188838c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49366
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Target added to INTERMEDIATE all operate on coreboot.pre, each modifying
the file in some way. When running them in parallel, coreboot.pre can be
read from and written to in parallel which can corrupt the result.
Add a function to create those rules that also adds existing
INTERMEDIATE targets to enforce an order (as established by evaluation
order of Makefile.inc files).
While at it, also add the addition to the PHONY target so we don't
forget it.
BUG=chromium:1154313, b:174585424
TEST=Built a configuration with SeaBIOS + SeaBIOS config files (ps2
timeout and sercon) and saw that they were executed.
Change-Id: Ia5803806e6c33083dfe5dec8904a65c46436e756
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49358
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: Ie3188d36e8ecacab42818c8619122751fcb7cdf8
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49379
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The ACPI part still needs some more code to be in place, so add that
later.
TEST=Together with the currently not merged rest of the amdfw patch
train applied this results in working serial console in bootblock in
Majolica.
Change-Id: Ia844e86a80c19026ac5b47a5a1e91c2553ea5cca
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49378
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I9d7574b60640eaf9a47a797e823324edeaf1e770
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48609
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
Change-Id: I1a01cc745c7049dc672bca12df5c6b764ac9b907
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49376
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Since the functions that get called by the coreboot console
initialization code aren't in the SOC-specific code anymore, the SOC's
uart.c can be included unconditionally in the build now. This also
replaces the STONEYRIDGE_UART Kconfig option with the common
AMD_SOC_CONSOLE_UART one.
Change-Id: I09c15566a402895d6388715e8e5a802dc3c94fdd
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49375
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I5079decfae982d2222bb9a7f5155d51885d4d3a9
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49374
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This will result in less code duplication when the common AMD SoC UART
support gets used for more AMD SoCs.
Change-Id: Id1786f32324de3e3947d792c599e2019705c5a85
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49373
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This partially reverts commit 6f8f9c969be9d471464f1b6a42b4bb1c2590db5c
by moving CONSOLE_UART_BASE_ADDRESS back to the SoC-specific code, since
the number and base addresses of UARTs turned out to be rather SoC-
specific. The help text for the AMD_SOC_CONSOLE_UART option also
contained those base addresses, so remove that as well.
Change-Id: I01211ec62421c56f22ed611313d6245a05bdea67
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49372
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The UARTs in the Picasso SoC are memory mapped, but there is also some
hardware support that isn't used by any board to make the UARTs behave
like the ones found on legacy x86 machines from the 90s.
In the MMIO mode the MMIO address of the UART controller is passed to
the OS via ACPI. The OS expects the base clock of the UART controller to
be 48MHz (see the cz_uart_desc struct in drivers/acpi/acpi_apd.c and
drivers/tty/serial/8250/8250_dw.c in the Linux kernel) in this case. It
is also possible to enable additional decodes from four 8 byte legacy
I/O locations used for serial ports to the different UART controllers,
which doesn't disable the MMIO access though. The legacy I/O-mapped
serial ports are usually expected to have a base clock of 16*115200Hz
which the hardware can also provide to the UART's baud rate generator.
So there are two possible valid configurations to use the UARTs; either
MMIO access in combination with a 48MHz base clock or the legacy I/O
decode with a ~1.8MHz base clock.
The existing code unconditionally generates ACPI objects for all enabled
UARTs, so those shouldn't be put into legacy mode and switching the base
clock to ~1.8MHz was only done in the case that the UART was used as
coreboot console UART which still used the MMIO access, but the lower
base clock. Since no board even selects this option and it's rather
invasive to properly implement this feature, just drop the corresponding
broken code.
TEST=SoC UART console still works on Mandolin.
Change-Id: I26fa8fdfc781b583ba56ac4dbcbbfb6100e84852
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reported-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49371
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This is causing boot errors on zork:
coreboot-v1.9308_26_0.0.22-18590-g4598a7bed945 Wed Dec 16 17:32:25 UTC 2020 bootblock starting (log level: 8)...
Family_Model: 00820f01
PSP boot mode: Development
Silicon level: Pre-Production
PMxC0 STATUS: 0x800 BIT11
I2C bus 3 version 0x3132322a
DW I2C bus 3 at 0xfedc5000 (400 KHz)
FMAP: area FW_MAIN_B found @ 312000 (3137280 bytes)
ASSERTION ERROR: file 'src/commonlib/bsd/cbfs_mcache.c', line 106
BUG=b:177323348
TEST=Boot ezkinil to OS
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I1f2bbdd9c87c4efdfb0042e90a20b489fa0efced
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49128
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
Change-Id: I61a9b07ec3fdaeef0622df82e106405f01e89a9e
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48719
Reviewed-by: Lance Zhao
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I515e830808a95eee3ce72b16fd26da6ec79dac85
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48718
Reviewed-by: Lance Zhao
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Replace acpi_create_gnvs() under soc/ to reflect their
changed functionality.
Change-Id: I61010f64a4a935f238e6dcd0f8c1340a6cc68eb4
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44024
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jason Glenesk <jason.glenesk@gmail.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Change-Id: I80f92bed737904e6ffc858b45459405fe76f1d04
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48851
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jason Glenesk <jason.glenesk@gmail.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
This change lets IOM consider all USB connected devices as device
attached(DA) scenario. While connecting a typec-to-a dongle, IOM would
disable TC cold and help to resolve enemuration failure after usb3
device is plugged into the dongle.
BUG=b:173054070
TEST=Build and boot on delbin.
Signed-off-by: Srinidhi N Kaushik <srinidhi.n.kaushik@intel.com>
Change-Id: I0ad0322693b4f8fbf1000b24eb21dddcebec686b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49244
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: John Zhao <john.zhao@intel.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The name `..._index` is confusing since the maximum index of an array is
not `ARRAY_SIZE(array)` but `ARRAY_SIZE(array) - 1`.
Rename `uart_max_index` to `uart_ctrlr_config_size` to make the name
match the variable´s value.
Change-Id: I7409c9dc040c3c6ad718abc96f268c187d50d79c
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49305
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
It is only used in one place, and there's two other equivalent macros.
Change-Id: I7c8241e28f688abd2df8180559dd02ee441c7023
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49282
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
This change adds a helper function `pcie_rp_enable_mask()` that
returns a 32-bit mask indicating the status (enabled/disabled) of PCIe
root ports (in the groups table) as configured by the mainboard in the
device tree.
With this helper function, SoC chip config does not need to add
another `PcieRpEnable[]` config to identify what root ports are
enabled.
Change-Id: I7ce5fca1c662064fd21f0961dac13cda1fa2ca44
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48968
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
TEST=Able to build and boot ADLRVP.
Change-Id: Ia331998b46abcf10e939078dea992589f09139bd
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49301
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add SLP_S0 residency register and enable LPIT support.
Change-Id: Id1abbe8dcb7796eeb26ccb72f1f26cf7a040dba4
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49048
Reviewed-by: Lance Zhao
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Test: Linux adds the cpuidle sysfs interface; Windows with s0ix_enable=1
boots without crashing with an INTERNAL_POWER_ERROR.
Change-Id: Icccd9d15a9e9a22c9bfe7a9843e95d77013c9c8f
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49047
Reviewed-by: Lance Zhao
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Test: Linux adds the cpuidle sysfs interface; Windows with s0ix_enable=1
boots without crashing with an INTERNAL_POWER_ERROR.
- Windows and Linux tested on google/akemi
- Linux tested on clevo/cml-u
Change-Id: I51fdf52419aa7f059b70a906fd8bdac88d5b6046
Tested-By: Matt DeVillier <matt.devillier@gmail.com>
Tested-by: Michael Niewöhner <foss@mniewoehner.de>
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49046
Reviewed-by: Lance Zhao
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add support for the Intel LPIT table to support reading Low Power Idle
Residency counters by the OS. On platforms supporting S0ix sleep states
there can be two types of residencies:
* CPU package PC10 residency counter (read from MSR via FFH interface)
* PCH SLP_S0 assertion residency counter (read via memory mapped
interface)
With presence of one or both of these counters in the LPIT table, Linux
dynamically adds the corresponding attributes to the cpuidle sysfs
interface, that can be used to read the residency timers:
* /sys/devices/system/cpu/cpuidle/low_power_idle_cpu_residency_us
* /sys/devices/system/cpu/cpuidle/low_power_idle_system_residency_us
The code in src/acpi implements generic LPIT support. Each SoC or
platform has to implement `acpi_fill_lpit` to fill the table with
platform-specific LPI state entries. This is done in this change for
soc/intel/common, while being added as its own compilation unit, so SoCs
not yet using common acpi code (like Skylake) can use it, too.
Reference:
https://uefi.org/sites/default/files/resources/Intel_ACPI_Low_Power_S0_Idle.pdf
Test: Linux adds the cpuidle sysfs interface; Windows with s0ix_enable=1
boots without crashing with an INTERNAL_POWER_ERROR.
- Windows and Linux tested on google/akemi together with CB:49046
- Linux tested on clevo/cml-u, supermicro/x11ssmf together with CB:49046
Change-Id: I816888e8788e2f04c89f20d6ea1654d2f35cf18e
Tested-by: Matt DeVillier <matt.devillier@gmail.com>
Tested-by: Michael Niewöhner <foss@mniewoehner.de>
Signed-off-by: Shaunak Saha <shaunak.saha@intel.com>
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49045
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Drop the support for the Intel Cannon Lake SoC for various reasons:
* Most people can't use coreboot on Cannon Lake, since the required FSP
binaries aren't publicly available. Given that FSP binaries for several
newer platforms have been released, it's very unlikely that Cannon Lake
FSP will ever be released.
* It seems there is no interest in this, since the reference mainboard
is the only available mainboard in tree.
Also, remove the related reference mainboard intel/cannonlake_rvp and
its FSP headers in intel/fsp2_0/cannonlake.
Change-Id: I8f698e16099acb45444b2bc675642d161ff8c237
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48775
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change adds a minimal chipset tree with only two devices:
1. Domain
2. GNB root complex
This allows sconfig to generate the config structure for SoC root
device that is used by config_of_soc().
Change-Id: I7e08ecf4b9556dc9325bd5a6a51566a949ceb73f
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49245
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Jason Glenesk <jason.glenesk@gmail.com>
|
|
This change updates various uart_* functions to use simple(_s_)
variants of PCI functions. This is done for a few reasons:
* __SIMPLE_DEVICE__ check can be dropped since the same data type can
be used in early stages and ramstage.
* Removes the requirement on early stage to walk the device tree to
get access to the device structure. This allows linker-based device
tree optimizations for early stages.
As part of this change, uart_get_device() is refactored and a new
function uart_console_get_devfn() is added which returns pci_devfn_t
in MMCONF format. It is then used directly by the _s_ variants of PCI
functions.
Change-Id: I344037828118572ae5eb27c82c496d5e7a508a53
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49213
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
This change renames `struct uart_gpio_pad_config` to `struct
uart_controller_config` and adds a new parameter devfn (which expects
devfn for the UART controller corresponding to the index in
PCI_DEVFN() format). This gets rid of the SoC callback to get `struct
device` pointer to the UART controller device.
Change-Id: Id0712a0038f2cc1a61b8b5a58fa155f14e7949a5
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49212
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Prevent the FSP from writing its default SVID SDID values of 8086:7270
for internal devices as this locks most of the registers. Allows the
subsystemid values set in devicetree to be used.
A description of this SSID table override behavior, along with example
code, is provided in the TigerLake FSP Integration Guide, section
15.178 ("SI_CONFIG Struct Reference").
The xHCI and HDA devices have RW/L registers rather than RW/O registers.
They can be written to multiple times but cannot be modified after
being locked, which happens during FspSiliconInit. Because coreboot
populates subsystem IDs after SiliconInit, these devices specifically
must be written beforehand or will otherwise be locked with their
default values of 0:0.
Tested by checking lspci output on System76 galp3-c (WHL), oryp5 (CFL),
and oryp6 (CML).
References:
- TigerLake FSP Integration Guide
- Intel Document Number 337868-002
Change-Id: Ieaa45ef7fa8e0da4a25b9174ded1ea0c5d9c4b4e
Signed-off-by: Jeremy Soller <jeremy@system76.com>
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49104
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Separate GPIO define into gpio_defs.h, then we can use it in asl include.
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: If2a779eae228f621e77610889205853de2fb179a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49216
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
The xHCI controller supports waking the system from S1-S4.
Thus specify that the deepest sleep state is S4 in _PRW.
Tested on Prodrive/hermes. The board now wakes from S4 as well by
pressing a key on the USB keyboard.
Change-Id: I0bb266e70ee6b4eb8922671b7d0078db0d29a1da
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49224
Reviewed-by: Christian Walter <christian.walter@9elements.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
List of changes:
1. Create new Kconfig MAX_CPU_ROOT_PORTS and MAX_PCH_ROOT_PORTS as per
EDS.
2. Add new chip variable to enable/disable CPU PCIE RPs from mainboards.
3. Rename PcieRpEnable to PchPcieRpEnable.
4. Enable CPU RPs as below in mainboard devicetree.cb
RP1: PEG60 : 0:6:0 : CPU SSD1
RP2: PEG10 : 0:1:0 : x8 CPU Slot
RP3: PEG62 : 0:6:2 : CPU SSD2
Change-Id: I92123450bd7cfb2e70aae8de03053672a7772451
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49136
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This is needed to allow switching to Haswell CPU code in the future.
Change-Id: Ic642f32f9c4a269a66ac470b7a7217f20ff8bfba
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46886
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Only a google/cyan variant evalutes BDID in ASL.
Change-Id: I3d839333333b4762ae5350734c85471a3c12838a
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49003
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: Ic779a668ebaa4f0c9bdef95fd6de8f0179e8a534
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49004
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Replace acpi_create_gnvs() under soc/ to reflect their
changed funcionality.
Change-Id: I7bdbe0d6f795252e713e9785ada2b6320e6604b9
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48717
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Rename these to soc_fill_gnvs() and move the callsite away
from mb/.
Change-Id: I760c36f65c6122103f2be98fc11ee13832c2772e
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48716
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Rename acpi_create_gnvs() functions under mb/ to reflect
their changed functionality.
Remove now empty mb/acpi_tables.c files.
Change-Id: Ia366867ef73d1ade9805dc29b8e14b3073f44f60
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48707
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Name the common part of GNVS initialisation as soc_fill_gnvs().
It is also moved before the call to acpi_create_gnvs(), which
followup will rename to mainbord_fill_gnvs() to reflect that
implementation is under mb/.
Change-Id: Ic4cf1548b65a86212d6e45d460fcd23bb8036365
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48706
Reviewed-by: Lance Zhao
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I45a2d9cb7f07609a1ff03fd70f17c3f2d4f013b9
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48705
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Move GNVS details to different function, called
from acpi_create_gnvs().
Change-Id: Ief02c078fe37753c0d29418394a351105a1aacc8
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48704
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Already done in common gnvs_get_or_create() implementation
once gnvs_chromeos_ptr() is defined for platforms.
Change-Id: I90fa2bc28ae76da734b3f88be057435aed9fe374
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48703
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Already done from common gnvs_get_or_create() implementation
after gnvs_cbmc_ptr() is defined.
Change-Id: I77c292cd9590d7fc54d8b21ea62717a2d77e5ba4
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48702
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Allocation now happens prior to device enumeration. The
step cbmem_add() is a no-op here, if reached for some
boards. The memset() here is also redundant and becomes
harmful with followup works, as it would wipe out the
CBMEM console and ChromeOS related fields without them
being set again.
Change-Id: I9b2625af15cae90b9c1eb601e606d0430336609f
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48701
Reviewed-by: Lance Zhao
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: Iddb0c20e769e6921ba5d0dd4a84ab9e494d522e1
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48269
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Nikolai Vyssotski <nikolai.vyssotski@amd.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
uart_common_init is not used outside of
soc/intel/common/block/uart.c. This change restricts the scope to this
file and drops the declaration from uart.h
Change-Id: I499a53506f9b2e91ecc7334bf9b023d342e802fc
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49211
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change updates the parameter passed into `lpss_set_power_state()`
from struct device * to pci_devfn_t. This allows the users in the
early stages to use pci_devfn_t instead of having to walk the device
tree to get a pointer to the relevant device structure. It is
important for optimizing out unnecessary components of the device tree
from the early stages.
Change-Id: Ic9e32794da65348fe2a0a2791db47ab83b64cb0f
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49210
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change drops the parameter `struct device *dev` from the function
`soc_get_gen_io_dec_range()`. This function uses the parameter dev to
get a pointer to config structure for extracting the decode ranges
configured by mainboard in device tree. However, there is no separate
chip driver for the LPC device which means that the SoC code can use
`config_of_soc()` to get to SoC chip config instead of using the LPC
device.
This change is being done in preparation to clean up the device
tree/chip config access in early stages that allows for optimizing
the inclusion of device tree elements in the early stages.
Change-Id: I3ea53ddc771f592dd0ea5e5e809be2d2eff7f16d
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49209
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
USB3 is in CPU and USB2 in PCH on Tigerlake. Cross die messaging is
implemented between CPU and PCH through the IOSF SB bridge. a PCH xHCI
USB2 port reset event issued by the xHCI driver shall trigger a message
upstream to CPU to wake it from the low power state which allows a USB3
device that downgraded to USB2 to upgrade back to USB3.
BUG=b:176575892
TEST=Built and booted to kernel on Voxel board.
Signed-off-by: John Zhao <john.zhao@intel.com>
Change-Id: I672f30a117980bc10bd71e9b77c5fa76286b9f5f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49052
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Chiranjeevi Rapolu <chiranjeevi.rapolu@intel.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This adds support for generating a PCI routing table that routes to the
GNB IO-APIC. This means we no longer need to route to the FCH IO-APIC
for PCI interrupts.
BUG=b:170595019
TEST=Boot ezkinil to OS with `pci=nomsi amd_iommu=off` and verify
all peripherals are working
CPU0 CPU1
0: 112 0 IO-APIC 2-edge timer
1: 0 99 IO-APIC 1-edge i8042
4: 0 2523 IO-APIC 4-edge ttyS0
5: 34632 0 IO-APIC 5-fasteoi mmc1
7: 5646 0 IO-APIC 7-fasteoi pinctrl_amd
8: 0 0 IO-APIC 8-edge rtc0
9: 0 33 IO-APIC 9-fasteoi acpi
10: 88258 0 IO-APIC 10-edge AMD0010:00
11: 0 32485 IO-APIC 11-edge AMD0010:01
24: 3301 0 amd_gpio 3 cr50_i2c
25: 0 235214 IO-APIC 28-fasteoi amdgpu
26: 67408 0 IO-APIC 31-fasteoi xhci-hcd:usb1
27: 0 488876 IO-APIC 8-fasteoi mmc0
28: 1265 0 amd_gpio 9 PNP0C50:00
29: 656 0 amd_gpio 12 ELAN9004:00
30: 413 0 amd_gpio 31 chromeos-ec
31: 14153 0 IO-APIC 4-fasteoi ath10k_pci
32: 2 0 sysfstrig0 cros-ec-accel_consumer3
33: 2 0 sysfstrig0 cros-ec-accel_consumer0
34: 6 0 amd_gpio 62 rt5682
35: 0 38937 IO-APIC 29-fasteoi snd_hda_intel:card0, ACP3x_I2S_IRQ
Cq-Depend: chrome-internal:3452710
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I3211ab351a332fafb7b5f9ef486bb6646d9a214c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48668
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nikolai Vyssotski <nikolai.vyssotski@amd.corp-partner.google.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Change-Id: I125e40204f3a9602ee5810d341ef40f9f50d045b
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48897
Reviewed-by: Idwer Vollering <vidwer@gmail.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|