| Age | Commit message (Collapse) | Author |
|---|
|
This patch correct Feedback divider setting:
1. Due to the use of a "by 2 pre-scaler," the range of the
feedback multiplication Feedback divider is limited to even
division numbers, and Feedback divider must be greater than
12, less than 1000.
2. Make the previously configured Feedback divider(LSB)
factors effective
Change-Id: Ic7c5c59be1d00c65c3b17cb3c4bfba8d7459e960
Signed-off-by: Lin Huang <hl@rock-chips.com>
Reviewed-on: https://review.coreboot.org/22468
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
As MIPI PHY document show, icpctrl<3..0> and lpfctrl<5..0>
should depend on frequency, so fix it.
Change-Id: Ic4a90767bd1f22d5d784d4013dc7afb3149115c1
Signed-off-by: Lin Huang <hl@rock-chips.com>
Reviewed-on: https://review.coreboot.org/22467
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Accroding to datasheet, feedback divider register high value is only
4 bit, it currently uses 5 bit, so correct it.
Change-Id: I1fe9fc076b712f27407c5f2735b15e64fb55e72e
Signed-off-by: Lin Huang <hl@rock-chips.com>
Reviewed-on: https://review.coreboot.org/22478
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Allows explicit ordering for vendors that share a common configuration
that must be sourced last.
The issue is that chips in soc/{amd,intel}/[ab].* will be able to
override defaults set in this file, but Kconfig files that get sourced
later (soc/amd/[d-z].*) will NOT be able to override these defaults.
Note: intel and amd soc chips now need to be added manually to the new
Kconfig file
BUG=b:62235314
TEST=make lint-stable
Change-Id: Ida82ef184712e092aec1381a47aa1b54b74ed6b6
Signed-off-by: Chris Ching <chingcodes@google.com>
Reviewed-on: https://review.coreboot.org/22123
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Split `i2c.h` into three pieces to ease reuse of the generic defi-
nitions. No code is changed.
* `i2c.h` - keeps the generic definitions
* `i2c_simple.h` - holds the current, limited to one controller driver
per board, devicetree independent I2C interface
* `i2c_bus.h` - will become the devicetree compatible interface for
native I2C (e.g. non-SMBus) controllers
Change-Id: I382d45c70f9314588663e1284f264f877469c74d
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/20845
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Our current struct for I2C segments `i2c_seg` was close to being compa-
tible to the Linux version `i2c_msg`, close to being compatible to SMBus
and close to being readable (e.g. what was `chip` supposed to mean?) but
turned out to be hard to fix.
Instead of extending it in a backwards compatible way (and not touching
current controller drivers), replace it with a Linux source compatible
`struct i2c_msg` and patch all the drivers and users with Coccinelle.
The new `struct i2c_msg` should ease porting drivers from Linux and help
to write SMBus compatible controller drivers.
Beside integer type changes, the field `read` is replaced with a generic
field `flags` and `chip` is renamed to `slave`.
Patched with Coccinelle using the clumsy spatch below and some manual
changes:
* Nested struct initializers and one field access skipped by Coccinelle.
* Removed assumption in the code that I2C_M_RD is 1.
* In `i2c.h`, changed all occurences of `chip` to `slave`.
@@ @@
-struct i2c_seg
+struct i2c_msg
@@ identifier msg; expression e; @@
(
struct i2c_msg msg = {
- .read = 0,
+ .flags = 0,
};
|
struct i2c_msg msg = {
- .read = 1,
+ .flags = I2C_M_RD,
};
|
struct i2c_msg msg = {
- .chip = e,
+ .slave = e,
};
)
@@ struct i2c_msg msg; statement S1, S2; @@
(
-if (msg.read)
+if (msg.flags & I2C_M_RD)
S1 else S2
|
-if (msg.read)
+if (msg.flags & I2C_M_RD)
S1
)
@@ struct i2c_msg *msg; statement S1, S2; @@
(
-if (msg->read)
+if (msg->flags & I2C_M_RD)
S1 else S2
|
-if (msg->read)
+if (msg->flags & I2C_M_RD)
S1
)
@@ struct i2c_msg msg; expression e; @@
(
-msg.read = 0;
+msg.flags = 0;
|
-msg.read = 1;
+msg.flags = I2C_M_RD;
|
-msg.read = e;
+msg.flags = e ? I2C_M_RD : 0;
|
-!!(msg.read)
+(msg.flags & I2C_M_RD)
|
-(msg.read)
+(msg.flags & I2C_M_RD)
)
@@ struct i2c_msg *msg; expression e; @@
(
-msg->read = 0;
+msg->flags = 0;
|
-msg->read = 1;
+msg->flags = I2C_M_RD;
|
-msg->read = e;
+msg->flags = e ? I2C_M_RD : 0;
|
-!!(msg->read)
+(msg->flags & I2C_M_RD)
|
-(msg->read)
+(msg->flags & I2C_M_RD)
)
@@ struct i2c_msg msg; @@
-msg.chip
+msg.slave
@@ struct i2c_msg *msg; expression e; @@
-msg[e].chip
+msg[e].slave
@ slave disable ptr_to_array @ struct i2c_msg *msg; @@
-msg->chip
+msg->slave
Change-Id: Ifd7cabf0a18ffd7a1def25d1d7059b713d0b7ea9
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/20542
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Starting with RK3399, PMUGPIO pull registers use the same write mask
format as normal GRF registers, so they need to use RK_CLRSETBITS()
rather than clrsetbits_le32().
BRANCH=None
BUG=None
TEST=boot from scarlet
Change-Id: Ibe391273d58ab35df993e149187d67497fcf2acc
Signed-off-by: Lin Huang <hl@rock-chips.com>
Reviewed-on: https://review.coreboot.org/20871
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
some gpio irq need to set input pull initialization status
to guarantee to get the right irq trigger. let's add this argument
in gpio_input_irq() function
BRANCH=None
BUG=None
TEST=boot from bob
Change-Id: I9b8e6497f07146dafdb447a6ea10d039a2a2fa33
Signed-off-by: Lin Huang <hl@rock-chips.com>
Reviewed-on: https://review.coreboot.org/20866
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Our structure packing for Rockchip's gpio_t was chosen arbitrarily. ARM
Trusted Firmware has since become a thing and chosen a slightly
different way to represent GPIOs in a 32-bit word. Let's align our
format to them so we don't need to remember to convert the values every
time we pass them through.
CQ-DEPEND=CL:572228
Change-Id: I9ce33da28ee8a34d2d944bee010d8bfc06fe879b
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/20586
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch updates the coreboot DDR Settings to match the configuration
used by ARM-Trusted-Firmware.
Change-Id: I34bc2950a9708ac89a5637bf682551e03d993fcc
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Reviewed-on: https://review.coreboot.org/20304
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
The differential signal of DQS needs to keep low
level before gate training. RPULL will connect
4Kn from PADP to VSS and a 4Kn from PADN to
VDDQ to ensure it. But if it has PHY side ODT
connected at this time, it will change the DQS
signal level. So it needs to disable PHY side ODT
when doing gate training.
BRANCH=None
BUG=None
TEST=boot from bob
Change-Id: I56ace8375067aa0bb54d558bc28172b431b92ca5
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Original-Commit-Id: cb024042c7297a6b17c41cf650990cd342b1376f
Original-Change-Id: I33cf743c3793a2765a21e5121ce7351410b9e19d
Original-Signed-off-by: Lin Huang <hl@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/448278
Original-Commit-Ready: Caesar Wang <wxt@rock-chips.com>
Original-Tested-by: Caesar Wang <wxt@rock-chips.com>
Original-Reviewed-by: Derek Basehore <dbasehore@chromium.org>
Reviewed-on: https://review.coreboot.org/18582
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
MAINBOARD_FORCE_NATIVE_VGA_INIT is to be selected instead of the user
option MAINBOARD_DO_NATIVE_VGA_INIT. The distinction is necessary to
use the latter in a choice.
Change-Id: I689aa5cadea9e1091180fd38b1dc093c6938d69c
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/19813
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Like HAVE_VGA_TEXT_FRAMEBUFFER, these are selected by graphics drivers
that support a linear framebuffer. Some related settings moved to the
drivers (i.e. for rockchip/rk3288 and nvidia/tegra124) since they are
hardcoded.
Change-Id: Iff6dac5a5f61af49456bc6312e7a376def02ab00
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/19800
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This patch fix rk_mipi_dsi_phy_init error return.
Change-Id: Ie260975ad6ed26c37aa8bb65dfcef4db2407a2da
Signed-off-by: Nickey Yang <nickey.yang@rock-chips.com>
Reviewed-on: https://review.coreboot.org/19903
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
It seems that the BootROM on the RK3399 overwrites some of the earlier
parts of SRAM, including the PRERAM_CBMEM_CONSOLE area. Now that we have
a persistent CBMEM console we want that area to survive in case of an
early (pre-CBMEM) reboot, so shuffle the layout around a bit to move it
further back. (This reduces the stack size to 12KB which should still be
way more than enough.)
Change-Id: Ifc1e568cda334394134bba9eba75088032d2ff13
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/19784
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
This is in preparation to get rid of the strong spi_setup_slave
implemented by different platforms.
BUG=b:38430839
Change-Id: I66b1b9635ece2381f62f2a9d6f5744d639d59163
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/19771
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Philippe Mathieu-Daudé <philippe.mathieu.daude@gmail.com>
|
|
Reserve the whole TZRAM area because it will be marked as secure-only
by BL31 and can not be accessed by the non-secure kernel.
CQ-DEPEND=CL:452659
BUG=chrome-os-partner:57361
BRANCH=firmware-gru-8785.B
TEST=the reserve memory is resized
Change-Id: Ie3ab39598f3f7cb96feb0c574e230e7fcb53a1a4
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: f34d254e1dfc9ae95a784aba22503e75a2fa65f1
Original-Change-Id: I39c4cb530f41a7b0f7f3064125072dd85b62276f
Original-Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/418102
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Original-(cherry picked from commit ea9fe064a9b1e1ce81fca74f829a0fb6e78ce426)
Original-Reviewed-on: https://chromium-review.googlesource.com/452640
Original-Tested-by: Julius Werner <jwerner@chromium.org>
Original-Commit-Queue: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/19431
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
This patch configures clock for mipi and then
adds mipi driver for support innolux-p079zca
mipi panel in rk3399 scarlet.
Change-Id: I02475eefb187c619c614b1cd20e97074bc8d917f
Signed-off-by: Nickey Yang <nickey.yang@rock-chips.com>
Reviewed-on: https://review.coreboot.org/19477
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
The hang was caused by deasserting the reset before, it had been delayed 20us
fixing the hang issue.
So we can remove this delay for now.
Change-Id: I5545377b72eb20b59ceaaca25c78965854bfb919
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Reviewed-on: https://review.coreboot.org/19699
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Spread Spectrum Modulator (SSMOD) is a fully-digital circuit used to
modulate the frequency of the Silicon Creations’ Fractional PLL in order
to reduce EMI.
We need to turn the DPLL spread spectrum feature on to
reduce the EMI noise for DDR on bob.
Change-Id: I75461d4235bcf55324e6664a1220754e770b4786
Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Reviewed-on: https://review.coreboot.org/19557
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
spi_crop_chunk is a property of the SPI controller since it depends
upon the maximum transfer size that is supported by the
controller. Also, it is possible to implement this within spi-generic
layer by obtaining following parameters from the controller:
1. max_xfer_size: Maximum transfer size supported by the controller
(Size of 0 indicates invalid size, and unlimited transfer size is
indicated by UINT32_MAX.)
2. deduct_cmd_len: Whether cmd_len needs to be deducted from the
max_xfer_size to determine max data size that can be
transferred. (This is used by the amd boards.)
Change-Id: I81c199413f879c664682088e93bfa3f91c6a46e5
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/19386
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Tested-by: coreboot org <coreboot.org@gmail.com>
|
|
Board Scarlet doesn't use usbphy1.
BUG=b:37685249
TEST=boot Scarlet, check the firmware log, and confirm
no errors about USB1
Change-Id: I66e0d8a235cc9057964f7abca32bc692d41e88fd
Signed-off-by: Philip Chen <philipchen@google.com>
Reviewed-on: https://review.coreboot.org/19489
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Change-Id: Id90aa210ff72092c4ab638a7bafb82bd11889bdc
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/19502
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
BUG=b:35647967
TEST=boot from bob
Change-Id: I5de902ab26fe768b641f69d85a5294baf6d916e3
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 223257d486b026c06a1f3a7a830b829efb9932dc
Original-Change-Id: I055ad5f59285cee3110d1e7cb1a53a60144712e4
Original-Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/452285
Original-Commit-Ready: Caesar Wang <wxt@rock-chips.com>
Original-Tested-by: Caesar Wang <wxt@rock-chips.com>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/19433
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
In builds without CONFIG_VBOOT_SEPARATE_VERSTAGE, verstage files are
linked directly into the bootblock or the romstage. However, they're
still compiled with a separate "libverstage" source file class, linked
into an intermediate library and then linked into the final destination
stage.
There is no obvious benefit to doing it this way and it's unclear why it
was chosen in the first place... there are, however, obvious
disadvantages: it can result in code that is used by both libverstage
and the host stage to occur twice in the output binary. It also means
that libverstage files have their separate compiler flags that are not
necessarily aligned with the host stage, which can lead to weird effects
like <rules.h> macros not being set the way you would expect. In fact,
VBOOT_STARTS_IN_ROMSTAGE configurations are currently broken on x86
because their libverstage code that gets compiled into the romstage sets
ENV_VERSTAGE, but CAR migration code expects all ENV_VERSTAGE code to
run pre-migration.
This patch resolves these problems by removing the separate library.
There is no more difference between the 'verstage' and 'libverstage'
classes, and the source files added to them are just treated the same
way a bootblock or romstage source files in configurations where the
verstage is linked into either of these respective stages (allowing for
the normal object code deduplication and causing those files to be
compiled with the same flags as the host stage's files).
Tested this whole series by booting a Kevin, an Elm (both with and
without SEPARATE_VERSTAGE) and a Falco in normal and recovery mode.
Change-Id: I6bb84a9bf1cd54f2e02ca1f665740a9c88d88df4
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/18302
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This patch attempts to finish the separation between CONFIG_VBOOT and
CONFIG_CHROMEOS by moving the remaining options and code (including
image generation code for things like FWID and GBB flags, which are
intrinsic to vboot itself) from src/vendorcode/google/chromeos to
src/vboot. Also taking this opportunity to namespace all VBOOT Kconfig
options, and clean up menuconfig visibility for them (i.e. some options
were visible even though they were tied to the hardware while others
were invisible even though it might make sense to change them).
CQ-DEPEND=CL:459088
Change-Id: I3e2e31150ebf5a96b6fe507ebeb53a41ecf88122
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/18984
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
It may cause an edp aux transfer error if the edp pclk is
set too high, so reduce it to 25MHz.
BUG=chrome-os-partner:60130
BRANCH=None
TEST=Build and Boot
Change-Id: Id1063baa5a82637b03c0f1f754181df074ab17cc
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 8f7ce31a7483e765ae0c86f8e62ef51413ee1596
Original-Change-Id: Ibb86c12c1d7c00dc3b4cc7a6bdf3bd6e895cd9f3
Original-Signed-off-by: Lin Huang <hl@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/429410
Original-Commit-Ready: Julius Werner <jwerner@chromium.org>
Original-Tested-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/18178
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
After we set the GET_TIME bit, the rtc time can't be read immediately. We
should wait up to 31.25 us, about one cycle of 32khz. Otherwise reading
RTC time will return a old time.
BUG=chrome-os-partner:61078
BRANCH=veyron
TEST=Build and Boot
Original-Change-Id: I6ec07fc6c4d6d8b27b12031423b86b8ab15da6f6
Original-Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/423272
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Change-Id: I9806b624d6e968e51d52aab8c052ae3fa77f247d
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: b4b708e29fbae0d8f5a2cece79711aa6b1887727
Original-Change-Id: I8c168c14437bb932a59ac0e91a01062df0cf11dc
Original-Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/427522
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/18127
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Updated to arm-trusted-firmware TOT:
236c27d2 (Merge pull request #805 from Xilinx/zynqmp/addr_space_size)
183 commits between Sep 20, 2016 and January 10, 2017
- Also add associated change to src/soc/rockship/rk3399 Makefile.inc
that is required to build the M0 Firmware.
Change-Id: I49695f3287a742cd1fb603b890d124f60788f88f
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/18024
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
I've recently added an assertion to ensure that the effective I2C
frequency on Rockchip SoCs is not too far off the 400KHz target due to
divisor rounding errors. A 10KHz margin worked fine for RK3399, but it
turns out that RK3288 actually only ever hit 387KHz since its I2C clocks
are based off the already pretty low 75MHz PCLKs. While we could
probably change the PCLKs to make this closer, that seems like a too
intrusive change for something that has already worked just fine for
years, so just loosen the restriction a little more instead.
BRANCH=None
BUG=chromium:675043
TEST=None
Change-Id: I7e96a1a75b38f8ad3971dd33046699cceb17b80d
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/421095
Reviewed-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://review.coreboot.org/18007
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Set aclk_emmc and clk_emmc to 148.5MHz under hs400es mode, which could
improve stability like kernel.
CQ-DEPEND=CL:386527
BUG=chrome-os-partner:54377
BRANCH=none
TEST=build and boot on kevin
Change-Id: Iaa76d3ec1ab999eb317a9ab6c7e3525594b15b57
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: e6eb1f56371aea51f2584a97bf817189d61090b2
Original-Change-Id: If4754d22e83a0f9a029fedca12f26ff5ae8d44e1
Original-Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/386865
Original-Commit-Ready: Julius Werner <jwerner@chromium.org>
Original-Tested-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/17790
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
We may support different sdram sizes on one board in future, so
we need to calculate sdram sizes from sdram drvier.
BRANCH=None
BUG=None
TEST=boot kevin
Change-Id: I43e8f164ecdb768c051464b4dbc7d890df8055d0
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 3c4d8b3cb647b2f9cebc416c298817c16d49330e
Original-Change-Id: I95d5ef34de9d79ebca3600dc7a4b9e14449606ff
Original-Signed-off-by: Lin Huang <hl@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/411600
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/17629
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Follow on patch to clean up the previous retry code.
Previous patches:
coreboot commit 079b5c65
(rockchip/rk3399: display: Retry edp initialization if it fails)
cros commit 28c57a6e
(rockchip/rk3399: display: retry edp initialization if edp initial fail)
- Reduce the jumping around via goto statements
- Break the retry code out into a separate function that also
prints the error messages.
BRANCH=gru
BUG=chrome-os-partner:60150
TEST=Rebuild Kevin and Gru
Change-Id: I3b6cf572073e4dcac83da09621bafde179af2613
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/17642
Tested-by: build bot (Jenkins)
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
1. Define a new structure spi_ctrlr that allows platforms to define
callbacks for spi operations (claim bus, release bus, transfer).
2. Add a new member (pointer to spi_ctrlr structure) in spi_slave
structure which will be initialized by call to spi_setup_slave.
3. Define spi_claim_bus, spi_release_bus and spi_xfer in spi-generic.c
which will make appropriate calls to ctrlr functions.
BUG=chrome-os-partner:59832
BRANCH=None
TEST=Compiles successfully
Change-Id: Icb2326e3aab1e8f4bef53f553f82b3836358c55e
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/17684
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
For spi_setup_slave, instead of making the platform driver return a
pointer to spi_slave structure, pass in a structure pointer that can be
filled in by the driver as required. This removes the need for platform
drivers to maintain a slave structure in data/CAR section.
BUG=chrome-os-partner:59832
BRANCH=None
TEST=Compiles successfully
Change-Id: Ia15a4f88ef4dcfdf616bb1c22261e7cb642a7573
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/17683
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
1. Use size_t instead of unsigned int for bytes_out and bytes_in.
2. Use const attribute for spi_slave structure passed into xfer, claim
bus and release bus functions.
BUG=chrome-os-partner:59832
BRANCH=None
TEST=Compiles successfully
Change-Id: Ie70b3520b51c42d750f907892545510c6058f85a
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/17682
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
TRAINING, not TARINING.
BUG=none
BRANCH=none
TEST=still builds
Change-Id: I8b7ffd0f0544a58865865a8b09d9c153db9c2674
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: b1ea846ce1ffd654d7d34c2a1d43b0fddbd4ae32
Original-Change-Id: I4940279ed7217cc20fe29c8b3603d1853acbfc5e
Original-Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/411801
Original-Commit-Ready: Patrick Georgi <pgeorgi@chromium.org>
Original-Tested-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Reviewed-by: Martin Roth <martinroth@chromium.org>
Reviewed-on: https://review.coreboot.org/17677
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
We found that sometimes the edp doesn't get the edid or that video
config fails on kevin after a reboot. Now we will retry 3 times to
initialize it if there are errors.
BRANCH=gru
BUG=chrome-os-partner:60150
TEST=reboot kevin, the edp initialization error is no longer seen.
Change-Id: I96e20e526294fbc856fbdffcbd63accdc7371ef6
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 28c57a6e5b89c7b3a96204ec19a080067460544a
Original-Change-Id: I1382cdf4119fc4eeae5c2b36485030e3a38c2d91
Original-Signed-off-by: Lin Huang <hl@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/412622
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/17626
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
RW flag was added to spi_slave structure to get around a requirement on
some AMD flash controllers that need to group together all spi volatile
operations (write/erase). This rw flag is not a property or attribute of
the SPI slave or controller. Thus, instead of saving it in spi_slave
structure, clean up the SPI flash driver interface. This allows
chipsets/mainboards (that require volatile operations to be grouped) to
indicate beginning and end of such grouped operations.
New user APIs are added to allow users to perform probe, read, write,
erase, volatile group begin and end operations. Callbacks defined in
spi_flash structure are expected to be used only by the SPI flash
driver. Any chipset that requires grouping of volatile operations can
select the newly added Kconfig option SPI_FLASH_HAS_VOLATILE_GROUP and
define callbacks for chipset_volatile_group_{begin,end}.
spi_claim_bus/spi_release_bus calls have been removed from the SPI flash
chip drivers which end up calling do_spi_flash_cmd since it already has
required calls for claiming and releasing SPI bus before performing a
read/write operation.
BUG=None
BRANCH=None
TEST=Compiles successfully.
Change-Id: Idfc052e82ec15b6c9fa874cee7a61bd06e923fbf
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/17462
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This changes the 933 DPLL rate to 928 which has low jitter.
BRANCH=none
BUG=chrome-os-partner:57845
TEST=boot kevin and run
while true; do sleep 0.1; memtester 500K 1 > /dev/null; done
for several hours
Change-Id: I4d2a8871aaabe3b0a1a165c788af265c5f9e892c
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 54ebf8763bb8193c4b36a5e86f0c625b176d31a6
Original-Change-Id: Iaa12bf67527b6d0e809657c513b8d1c66af25174
Original-Signed-off-by: Derek Basehore <dbasehore@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/404550
Original-Reviewed-by: Douglas Anderson <dianders@chromium.org>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/17379
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
The Kevin project has been too smooth and boring for our tastes in the
last last few weeks, so we've decided to stir the pot a little bit and
reshuffle all our PLL settings at the last minute. The new settings
match exactly what the Linux kernel expects on boot, so it doesn't need
to reinitialize anything and risk a glitch.
Naturally, changing PLL rates will affect child clocks, so this patch
changes vop_aclk (192MHz -> 200MHz, 400MHz in the kernel), pmu_pclk
(99MHz -> 96.57MHz) and i2c0_src (198MHz -> 338MHz, leading to an
effective I2C0 change 399193Hz -> 398584Hz).
BRANCH=gru
BUG=chrome-os-partner:59139
TEST=Booted Kevin, sanity checking display and beep. Instrumented
rockchip_rk3399_pll_set_params() in the kernel and confirmed that GPLL,
PPLL and CPLL do not get reinitialized anymore (with additional kernel
patch to ignore frac divider when it's not used). Also confirmed that
/sys/kernel/debug/clk_summary now shows pclk_pmu_src 96571429 because
the kernel doesn't even bother to reinitialize the divisor.
Change-Id: Ib44d872a7b7f177fb2e60ccc6992f888835365eb
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 9b82056037be5a5aebf146784ffb246780013c96
Original-Change-Id: Ie112104035b01166217a8c5b5586972b4d7ca6ec
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/405785
Original-Commit-Ready: Xing Zheng <zhengxing@rock-chips.com>
Original-Tested-by: Xing Zheng <zhengxing@rock-chips.com>
Original-Reviewed-by: Xing Zheng <zhengxing@rock-chips.com>
Original-Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-on: https://review.coreboot.org/17378
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
To avoid garbage display in firmware on warm reset, we need
to enable eDP display in depthcharge instead when the framebuffer is
cleared.
Therefore limit edp_enable() in coreboot to just configure eDP,
and leave enabling the display to depthcharge.
CQ-DEPEND=CL:402071
BUG=chrome-os-partner:58675
BRANCH=none
TEST=Boot from kevin, and display work
Change-Id: I9d937ead33ebba58e33e02fd73b80d6e11bb69aa
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 38b0d18c3fae37dfccb18fe809f763b98703167c
Original-Change-Id: Ibbc283a5892b98f4922f02fd67465fe2e1d01b71
Original-Signed-off-by: Lin Huang <hl@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/402095
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/17207
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Fix msch ddrconfig register write error. Also make sure that the row
number configured in msch is equal to the row number configured in the
DDR controller.
This would not affect systems with 4GB of memory, but is needed
for 2GB configurations.
BUG=None
BRANCH=None
TEST=Boot from kevin
Change-Id: Ic95b3371faec5b31c32b011c50e55e83d949e74d
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: dfa43d3d44839d9685b6393157f51b646e9996de
Original-Change-Id: I0c95378bf937a245b7cdc0583c5d2ed1347f2a3e
Original-Signed-off-by: Lin Huang <hl@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/399563
Original-Reviewed-by: Derek Basehore <dbasehore@chromium.org>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/17208
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
framebuffer address is dynamically chosen by libpayload now, so there's
no need to configure it in coreboot.
CQ-DEPEND=CL:401402
BUG=chrome-os-partner:58675
BRANCH=none
TEST=Boot from kevin, dev screen is visible
Change-Id: I9f1e581d5c63b3579b26be22ce5c8d1e71679f6f
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: b3b6675420592c30e1e0abc8f8e9dd6ed5abd04c
Original-Change-Id: I7e3162f24a4dc426fe4e10d74865cf0042c80db5
Original-Signed-off-by: Lin Huang <hl@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/401401
Original-Commit-Ready: Julius Werner <jwerner@chromium.org>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/17109
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Near the end of DDR initialization, the system switches to the index1
configuration. Sometimes this failed and a status bit that coreboot was
waiting for was never set, hanging the system.
Instead, give the system 100ms to reach the new configuration or reboot
it, which generally fixes the issue. Also reset when training the index1
configuration fails.
BUG=chrome-os-partner:57988
BRANCH=None
TEST=The error condition now leads to a reboot of coreboot which
recovers the system, instead of hanging.
Change-Id: Icb4270369102ff7a4ce91b0677e04b4eb10f1204
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: ca250d0628ea3b6b39d5131246eaba68637c5140
Original-Change-Id: Id6e8936d90e54b733ac327f8476d744b45639232
Original-Signed-off-by: Lin Huang <hl@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/399681
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/17106
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
1. Update write leveling value to 0x200.
When the wrdqs slave delay is changed to 0x200, the phase between the
dqs and the clock is 0 degrees. The pcb layout can make sure the tDQSS
timing is smaller than 0.25tck, so this value is useful for both higher
and lower frequencies.
2. Disable read leveling for LPDDR3.
The read leveling result is unreliable - the value is not in the middle
of the read eye. To fix this, disable read leveling and fix the read
DQSn slave delay setting for DQn to 0x080 (1/4 cycle delay of the
input signal).
BUG=None
BRANCH=None
TEST=Boot from kevin; Check by shmoo read eye and stability test, that
the updated value of 0x80 is better.
Change-Id: Ia72b601d9bf4e34ba1b0b4584b2c5c3ce9dafbd4
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 37e8dfe783db3ce71aa026b4609ed0bfa16db06f
Original-Change-Id: I2a5d40c0348449b2a7c609c1db65da4ed5f1c09f
Original-Signed-off-by: Lin Huang <hl@rock-chips.com>
Original-Signed-off-by: Jeff Chen <cym@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/396598
Original-Commit-Ready: Douglas Anderson <dianders@chromium.org>
Original-Reviewed-by: Derek Basehore <dbasehore@chromium.org>
Reviewed-on: https://review.coreboot.org/17105
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
To enable DDR Dynamic Voltage and Frequency Scaling (DVFS) we need to
train alternative configurations first, so do the training and store the
values.
BUG=None
BRANCH=None
TEST=Boot from kevin
Change-Id: I944a4b297a4ed6966893aa09553da88171307a42
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 94533ff3ba21bcb0ace00bedcf0cebb89a341be2
Original-Change-Id: I4a98bc0db5553d154fedb657e35b926a92aa80c7
Original-Signed-off-by: Lin Huang <hl@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/386596
Original-Commit-Ready: Douglas Anderson <dianders@chromium.org>
Original-Reviewed-by: Derek Basehore <dbasehore@chromium.org>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/17104
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Some of our RK3399 devices have panel resolutions as high as 2400x1600.
With 16bpp that barely still fit into an 8MB framebuffer, but then we
changed it to 32bpp for better image quality...
Note that this is a band-aid. Coreboot-allocated framebuffers shouldn't
be used at all on ARM64 devices, since libpayload is perfectly capable
to dynamically allocate it with the right size based on EDID-information
on this architecture. That will require some more elaborate work to be
fixed with later patches.
BRANCH=gru
BUG=chrome-os-partner:58044
TEST=Warm-reboot Kevin on the dev screen, confirm that you don't see the
lower half of the screen that overflowed our allocated framebuffer
preserved from the last boot as soon as the backlight turns on.
Change-Id: I00a63cfef35a8ee734543abbdb298344fb529283
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: d2718efcacb50371624d9f6a3b586c298e8c2fec
Original-Change-Id: Ia1fa28971c65d7d0639966e715f742309245172b
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/399966
Original-Reviewed-by: Daisuke Nojiri <dnojiri@chromium.org>
Reviewed-on: https://review.coreboot.org/17108
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
We found sdram may fail in pctl_cfg(), so we check the status in this
function. If it exceeds 100ms still in this function, we will restart
the system. We also found there are rare chances DDR training fails,
so also restart system in that case.
BUG=chrome-os-partner:57988
BRANCH=None
TEST=coreboot resets on failure and eventually the system comes up
Change-Id: Icc0688da028a8f4f81eafe36bbaa79fdf2bcea74
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 89e45f8352f62e19a203316330aba14ccc5c8b11
Original-Change-Id: If4e78983abcfdfe1e0e26847448d86169e598700
Original-Signed-off-by: Lin Huang <hl@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/397439
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/17045
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
This refactoring was already carried into RK3288 with commit 6911219
(edid: Add helper function to calculate bits-per-pixel dependent values)
but it seems that the code for RK3399 was copy&pasted from it too early
to pick this up. Fix that so that future Rockchip SoCs can copy&paste
the right thing.
Change-Id: I5050c58d18db38fffabc7666e67a622d4a828590
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/17050
Tested-by: build bot (Jenkins)
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Though we don't use Type-C PHY to support USB3 in firmware,
we still need to initialize the Type-C PHY, and make sure
the power state of pipe is always fixed to U2/P2. After
this, we can force USB3 controller to work in USB2 only
mode.
BRANCH=none
BUG=chrome-os-partner:56425
TEST=Go to recovery mode, plug a Type-C USB drive containing
chrome OS image into both ports in all orientations, check if
system can boot from USB.
Change-Id: I95bb96ff27d4fecafb7b2b9e9dc2839b5c132654
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 8ec98507845276119d8a9d5626934dedcb35f2dd
Original-Change-Id: Ie3654cd1c1cb76b62aa9b247879b60cbecee0155
Original-Signed-off-by: William wu <wulf@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/391412
Original-Commit-Ready: Julius Werner <jwerner@chromium.org>
Original-Tested-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/16910
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
CL:377541 was supposed to remove the big CPU cluster initialization from
rkclk_init() in the bootblock and move it to a more suitable place in
ramstage. Except that next to all the code cleanup I did in that patch,
I seem to have forgotten to actually remove that old code.
Big thanks to Nico for spotting that in the upstream coreboot review.
BRANCH=gru
BUG=chrome-os-partner:54906
TEST=Booted Kevin.
Change-Id: I09fe948b4587536802b42329b813177439e0804f
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 77f9eaf0446b22adfca79d0adf8a0ecfd93c0040
Original-Change-Id: I13dab208225b7e43ad864f2f3cf51b3c104acd4b
Original-Reported-by: Nico Huber <nico.h@gmx.de>
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/389236
Original-Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-on: https://review.coreboot.org/16769
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
This selects the rank to train before training is triggered. This is
to prevent any race conditions with the hardware.
BRANCH=none
BUG=chrome-os-partner:56940
TEST=stressapptest -M 1536 -s 1000
Change-Id: I892bace414cf4495619d41bdaea0c4e91c1e29b3
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 8f2dd6f52978a9e54ddd2688eb68fd237aabfe2d
Original-Change-Id: I4e7118d8509b59e391d0a254477b5390dfdd43a5
Original-Signed-off-by: Derek Basehore <dbasehore@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/387907
Original-Commit-Ready: Douglas Anderson <dianders@chromium.org>
Original-Tested-by: Douglas Anderson <dianders@chromium.org>
Original-Reviewed-by: Douglas Anderson <dianders@chromium.org>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-by: 云平 汤 <typ@rock-chips.com>
Reviewed-on: https://review.coreboot.org/16768
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
There are two modifications in the driver:
1. Correctly set speeds based on DDR frequency.
Control the speeds in the predriver circuits to reduce power.
SPEED[1:0]
2'b00:less than 800Mbps(400MHz)
2b01 : 800Mbps(400MHz) to 1600Mbps(800MHz)
2b10 : 1600Mbsp(800MHz) to 2400Mbps(1200MHz)
2b11 : 3200Mbps and greater
2. Configure the number of cycles for the phy clock pll wait time after
locking, based on the DDR config file.
BRANCH=none
BUG=chrome-os-partner:56940
TEST=do memtester on kevin board, and pass
Change-Id: Iaf6da59c6c5c290867e0922a2a99de272f4c7bde
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 125cf8afac3a682d33896fe74a20ba1d498a3bd2
Original-Change-Id: Iabc17df37a701c4f052540c3c259f209a1db3c59
Original-Signed-off-by: Lin Huang <hl@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/387428
Original-Reviewed-by: Douglas Anderson <dianders@chromium.org>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/16722
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins)
|
|
In USB2 only mode, the Type-C PHY will be held in reset and
only the USB2 logic of the USB3 OTG controller and PHY will be
used over the USB2 pins on the Type-C connector to support Low,
Full and High-speed USB operation.
BRANCH=none
BUG=chrome-os-partner:56425
TEST=Go to recovery mode, plug a Type-C USB drive containing
chrome OS image into both ports in all orientations, check if
system can boot from USB.
Change-Id: Ic265c0c91c24f63b2f9c3106eb2bb277a589233b
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: a37ccc5b6019967483eac6b5a360d67bc3326e93
Original-Change-Id: I582f04f84eef447ff0ba691ce60e9461ed31cfad
Original-Signed-off-by: Liangfeng Wu <wulf@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/385837
Original-Commit-Ready: Julius Werner <jwerner@chromium.org>
Original-Tested-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/16717
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
To improve sdram 800MHz and 933MHz stability, we
need to modify write leveling flow to get the
proper write leveling value.
BUG=chrome-os-partner:56940
BRANCH=none
TEST=Boot from kevin on 933MHz, and do stressapptest
Change-Id: I5b24c93d4a57917fb9af7e5e2a95d8423ccbaa7e
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: d84bf25b3e5de373c7913e6d534a810cb984b3fd
Original-Change-Id: I87efddf628c3683fcb85d6875e029cf3cbc482be
Original-Signed-off-by: Jianqun Xu <jay.xu@rock-chips.com>
Original-Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>
Original-Signed-off-by: Lin Huang <hl@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/384292
Original-Commit-Ready: Julius Werner <jwerner@chromium.org>
Original-Tested-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/16716
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
We found that we may want to load some components of BL31 on the RK3399
into SRAM. As usual, these components may not overlap any coreboot
regions still in use at that time, as is already statically checked by
the check-ramstage-overlaps rule in Makefile.inc.
On RK3399, the only such regions are TTB and STACK. This patch moves the
TTB region back to the end of SRAM (right before STACK), so that a large
contiguous region of SRAM before that remains usable for BL31.
BRANCH=gru
BUG=None
TEST=Booted Kevin.
Change-Id: I1689d0280d79bad805fea5fc3759c2ae3ba24915
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 1d4c6c6f6cc0efe97d6962a81e309a1c040d1def
Original-Change-Id: I37c94f2460ef63aec4526caabe58f35ae851bab0
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/384635
Original-Reviewed-by: Simon Glass <sjg@google.com>
Reviewed-on: https://review.coreboot.org/16714
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
With a SPI clock above about 24MHz the APB cannot keep up when doing
individual byte transfers. Adjust the driver to use 16-bit reads when
it can, to remove this bottleneck.
Any transaction which involves writing bytes still uses 8-bit transfers,
to simplify the code. These are the transfers that are not time-critical
since they tend to be small. The case that really matters is reading from
SPI flash.
In general we can use 16-bit reads anytime we are transferring an even
number of bytes. If the code detects an odd number of bytes, it tries to
perform the operation in two steps: once in 16-bit mode with an even
number of bytes, and once in 8-bit mode for the final byte. This allow
us to use 16-bit reads even if asked to transfer (for example) 0xf423
bytes.
The limit on in_now and out_now is adjusted to 0xfffe to avoid an extra
transfer when transferring ~>=64KB.
CQ-DEPEND=CL:383232
BUG=chrome-os-partner:56556
BRANCH=none
TEST=boot on gru and see that things still work correctly. I tested (with
extra debugging) that the 16-bit case is being picked when it should be.
Change-Id: If5effae9a84e4de06537fd594bedf7f01d6a9c88
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: ec250b4931c7d99cc014e32ab597fca948299d08
Original-Change-Id: Idc5b7e5d82cdbdc1e8fe8b2d6da819edf2d5570c
Original-Signed-off-by: Simon Glass <sjg@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/381312
Original-Commit-Ready: Julius Werner <jwerner@chromium.org>
Original-Tested-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/16712
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Some of the asserts for valid clock divisor ranges were off by one. This
patch corrects them and writes them all in a consistent way.
BRANCH=None
BUG=None
TEST=Booted Kevin.
Change-Id: I81749408a40822100797f1734f3b88987d12d8d5
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: e09cdfde26700496aaa1fc41489f63a355e8a89d
Original-Change-Id: I429edb99e2d5ff2302d9750e6569b3d21f5686fa
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/381574
Original-Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-on: https://review.coreboot.org/16704
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
This patch moves the big CPU cluster initialization on the RK3399 from
the clock init bootblock function into ramstage. We're only really doing
this to put the cluster into a sane state for the OS, we're never
actually taking it out of reset ourselves... so there's no reason to do
this so early.
Also cleaned up the interface for rkclk_configure_cpu() a bit to make it
more readable.
BRANCH=None
BUG=chrome-os-partner:54906
TEST=Booted Kevin.
Change-Id: I568b891da0abb404760d120cef847737c1f9e3ec
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: bd7aa7ec3e6d211b17ed61419f80a818cee78919
Original-Change-Id: Ic3d01a51531683b53e17addf1942441663a8ea40
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/377541
Original-Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-on: https://review.coreboot.org/16698
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
At higher SPI bus speeds the SPI RX value is not available in time for
sampling at the normal time. Add a delay to ensure that we read the
correct data.
The value of 40ns is chosen arbitrarily. In my testing I can use a sample
delay of 1 even at 24MHz. But since it is not necessary, I have left that
case alone. It kicks in at 25MHz and up.
BUG=chrome-os-partner:56556
BRANCH=none
TEST=boot on gru and see no change at current speed
Change-Id: I3ef335d9a532eaef1e76034bd02e185acf11176a
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: e9b620c47fc3e39211487507fadb8657afdebee7
Original-Change-Id: I65d66d752cbbbee4d02f475de23a52069a0e9782
Original-Signed-off-by: Simon Glass <sjg@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/381311
Original-Commit-Ready: Julius Werner <jwerner@chromium.org>
Original-Tested-by: Simon Glass <sjg@google.com>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/16707
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
This patch fixes a typo in the clock initialization code that caused the
PERILP1_PCLK_HZ constant to be ignored and the clock to always run at
the same speed as its parent (PERILP1_HCLK_HZ). Since we've done all our
previous tests and validation with this bug, we should probably increase
the value of the constant (that had not actually been used) to the value
that we had been incorrectly using instead (which also makes effective
SPI read times faster).
BRANCH=None
BUG=chrome-os-partner:56556
TEST=Booted Kevin.
Change-Id: Ibeb08f5fe5e984a74e3f57e60c62d4bfb644b6ca
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 06e605a5fcb9bdf13a3d301112380633b892fd4e
Original-Change-Id: Icb5e079f53eb22b0dbf0ea4d1c2ff08688e3fa8e
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/381031
Original-Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-on: https://review.coreboot.org/16703
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Output GPIOs should never have a pull-up or pull-down resistor attached
since they're actively driven. Since some GPIOs get initialized with a
pull at power-on reset, we should explicitly overwrite that setting.
Most other platforms do this on gpio_output, but Rockchip hadn't yet.
Also, shuffle some code around to make things cleaner and allow for
easier code reuse.
BRANCH=None
BUG=chrome-os-partner:52526
TEST=Booted Kevin.
Change-Id: I1425d074ea1e90f4484e1e84a8002b057192c5f7
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: df5b236bfd58b172435043c1cb792b917a4ec4ab
Original-Change-Id: I044266d71ef8bd0518316ff72d829d1ca1e30f35
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/382531
Original-Reviewed-by: Simon Glass <sjg@google.com>
Reviewed-on: https://review.coreboot.org/16710
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
As far as I know, the Cortex-A53 cores in RK3399 are of a newer revision
that is not affected by ARM erratum 843419. If it was, the workaround
would also need to be enabled in libpayload and Chrome OS userspace,
which it currently isn't. I assume this was just incorrectly copied over
from another SoC and we can safely remove it.
BRANCH=None
BUG=chrome-os-partner:56700
TEST=Booted Kevin.
Change-Id: I5b1534c954a6d985499b481738723cabbdc07253
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 4891cc866583532ee3dcb1a5ad5b81670eb0743d
Original-Change-Id: Iadb57428f8727ce0e563204723644e2c79e3007c
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/376363
Original-Commit-Queue: Douglas Anderson <dianders@chromium.org>
Original-Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-on: https://review.coreboot.org/16702
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
The SPI driver is quite slow at reading data. For example, with a 24MHz
clock on gru it achieves a read speed of only 13.9Mbps.
We can correct this by reading the status registers once, then reading as
many bytes as are available before checking the status registers again. It
seems likely that a status register read requires synchronizing with the
SPI FIFO clock domain, which takes a while.
BUG=chrome-os-partner:56556
BRANCH=none
TEST=run on gru and see the speed increase from 13.920 Mbps to 24.712 Mbps
Change-Id: I24aed0c9c6c5445634c4e056922afaee4e9a7b33
Signed-off-by: Martin Roth <martinroth@chromium.org>
Original-Commit-Id: 49c2fc20d7d7d703763e9b0a6f68313a349a84b9
Original-Change-Id: I42745f01f0fe069f6ae26d866004d36bb257e6b2
Original-Signed-off-by: Simon Glass <sjg@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/376945
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/16582
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
This patch adds support to reboot the whole board after a hardware
watchdog reset, to avoid the usual TPM issues. Work 100% equivalent to
Veyron.
From my tests it looks like both SRAM and PMUSRAM get preserved across
warm reboots. I'm putting the WATCHDOG_TOMBSTONE into PMUSRAM since that
makes it easier to deal with in coreboot (PMUSRAM is currently not
mapped as cached, so we don't need to worry about flushing the results
back before reboot).
BRANCH=None
BUG=chrome-os-partner:56600
TEST='stop daisydog; cat > /dev/watchdog', press CTRL+D, wait 30
seconds. Confirm that system reboots correctly without entering recovery
and we get a HW watchdog event in the eventlog.
Change-Id: I317266df40bbb221910017d1a6bdec6a1660a511
Signed-off-by: Martin Roth <martinroth@chromium.org>
Original-Commit-Id: 3b8f3d064ad56d181191c1e1c98a73196cb8d098
Original-Change-Id: I17c5a801bef200d7592a315a955234bca11cf7a3
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/375562
Original-Commit-Queue: Douglas Anderson <dianders@chromium.org>
Reviewed-on: https://review.coreboot.org/16578
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
This patch sets some magic number in magic undocumented registers that
are rumored to make USB 2.0 signal integrity better on Kevin. I don't
see any difference (unfortunately it doesn't solve the problems with
long cables on my board), but I guess it doesn't hurt either way.
BRANCH=None
BUG=chrome-os-partner:56108,chrome-os-partner:54788
TEST=Booted Kevin with USB connected through Servo. Seems to have
roughly the same failure rate as before.
Change-Id: If31fb49f1ed7218b50f24e251e54c9400db72720
Signed-off-by: Martin Roth <martinroth@chromium.org>
Original-Commit-Id: 0c5c8f0f80ea1ebb042bcb91506a6100833e7e84
Original-Change-Id: Ifbd47bf6adb63a2ca5371c0b05c5ec27a0fe3195
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/370900
Original-Reviewed-by: Guenter Roeck <groeck@chromium.org>
Original-Reviewed-by: David Schneider <dnschneid@chromium.org>
Reviewed-on: https://review.coreboot.org/16265
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Before, we calculate the pwm duties for cpu cores and centerlogic by
hand, adding pwm_regulator.c to handle this. The default pwm design
min/max voltage may be different between revs.
With the pwm regulator, this patch changes the little cpu frequency from
600M to 1512M, and raises CPU voltage to 1.2V correspondingly.
This also means we decide to drop the ES1 because it may fail to
bootup with 1.5G ~ 1.2v.
BRANCH=none
BUG=chrome-os-partner:54376,chrome-os-partner:54862
TEST=Bootup on kevin board
Change-Id: Id04c176bddfb9cdf3d25b65736e40249a85f6aa1
Signed-off-by: Martin Roth <martinroth@chromium.org>
Original-Commit-Id: ee4365c787ec523b7ee1028ea100dcfbb331b3a9
Original-Change-Id: Ide75bbd92d1cbb14f934baeec0e38862bc08402b
Original-Signed-off-by: Eric Gao <eric.gao@rock-chips.com>
Original-Signed-off-by: Shunqian Zheng <zhengsq@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/364410
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/16368
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
The romstage.c is more board related than soc specific, like
setting the pwm regulators, so moving it to mainboard/gru.
BRANCH=none
BUG=chrome-os-partner:54819
TEST=Bootup on kevin board
Change-Id: I83c6cde9f451480e47e2b4b549cedf65b345134c
Signed-off-by: Martin Roth <martinroth@chromium.org>
Original-Commit-Id: 35feeb07131a6a9de4adde035236987391833474
Original-Change-Id: If2bf245302eb4fb20bb089c1b3ffa03909722443
Original-Signed-off-by: Shunqian Zheng <zhengsq@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/375398
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/16367
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Since we now have so much more room for activities in our romstage SRAM
section, we can easily fit the LZMA decompressor to enable ramstage
compression. Also shuffle around memlayout sections a little more to
make use of unused space, and balance out leftover memory so that all
sections that might need future expansion have a reasonable amount.
Change-Id: I47f2d03e520fc3103ef04257b4ba7e93874b8956
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/16334
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This patch changes Gru SDRAM parameters from structures that just get
compiled into the romstage to individual CBFS files. This allows us to
only load the parameter set we need for the board we're booting from
flash, which reduces our boot time and the SRAM memory footprint
required to hold the romstage.
TEST=Booted Kevin.
Change-Id: Ie88a515cbdb19a794ca0a230a56bcc82bed1e550
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/16274
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
We should be running faster. Faster = better.
BRANCH=None
BUG=chrome-os-partner:54873
TEST=Boot; stressapptest -M 1028 -s 10000
Change-Id: I7f855960af3142efb71cf9c15edd1da66084e9d8
Signed-off-by: Martin Roth <martinroth@chromium.org>
Original-Commit-Id: 51bfd2abb1aba839bd0b5b85e9e918f3cc4fd94d
Original-Change-Id: Iec9343763c1a5a5344959b6e8c4dee8079cf8a20
Original-Signed-off-by: Lin Huang <hl@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/362822
Original-Reviewed-by: Douglas Anderson <dianders@chromium.org>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/16241
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
We're changing the PWM regulator bounds on Kevin from rev6 onwards, so
we'll need to use different duty cycle values for them. We really want a
proper PWM regulator driver that can calculate these values
automatically from voltages, but until we have that this patch just
hardcodes the new numbers in.
(Yes, this is a patch for the mainboard/google/gru board family that only
touches a file from the rockchip/rk3399 SoC. That too is something
that'll be fixed up in a later CL.)
BRANCH=None
BUG=chrome-os-partner:54888
TEST=Booted Kevin rev4 (for whatever that's worth...).
Change-Id: Ibb6ab5c6517d83ffb5e32cb17d0de33e8ec10293
Signed-off-by: Martin Roth <martinroth@chromium.org>
Original-Commit-Id: 4cb2a939295e2b6443c5dbd3374982224322304b
Original-Change-Id: I8757cc54f2478d20bb948a1a0a7398b0404a7b1f
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/368410
Original-Commit-Ready: Dan Shi <dshi@chromium.org>
Original-Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-on: https://review.coreboot.org/16235
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This reverts commit 462e1413 ("rockchip: rk3399: enable sdhci clk
for emmc")
Enabling this clock in coreboot is no longer needed as it's handled
in the kernel driver now.
BUG=chrome-os-partner:52873
TEST=boot from usb/sdcard and check there is /dev/mmcblk0
BRANCH=none
Change-Id: I92cf51f175fe56a09ab9329b29a27c77ef4328e1
Signed-off-by: Martin Roth <martinroth@chromium.org>
Original-Commit-Id: 5707d1269a253dabf825be120d1f9348ffaab6d0
Original-Change-Id: I8bca870c663d8ce8fac5daaaaf8225489f22ed13
Original-Signed-off-by: Shunqian Zheng <zhengsq@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/367421
Original-Commit-Ready: Brian Norris <briannorris@chromium.org>
Original-Reviewed-by: Douglas Anderson <dianders@chromium.org>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/16152
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
The Rockchip RK3399 integrates a USB Type-C PHY in charge of things like
SuperSpeed line muxing for rotated cable orientations in the SoC. While
fancy, this is very complicated and we don't want to implement support
for the whole thing in firmware. The USB Type-C standard has
intentionally been designed in a way that the USB 2.0 (HighSpeed) lines
always "just work" in any orientation (by just shorting different pins
in the connector together) so that simple use cases like ours can get
basic USB functionality without much hassle.
However, a semi-configured Type-C PHY can confuse USB 3.0 capable
devices into thinking we're actually supporting SuperSpeed, and fail at
that rather than establishing a reliable HighSpeed connection. This
patch sets enough bits in the Type-C PHY to electrically isolate the
SuperSpeed lines from the connector so that the connected device isn't
going to get any fancy ideas and reliably falls back to USB 2.0.
Also clean up the rest of the USB code while we're at it: avoid writing
a few bits that are already in the right state from their reset values
anyway, or reading values whose content we already know for this SoC.
Rename the USB controllers to the name actually used in the Rockchip
documentation (USB OTGx) rather than the name blindly copied from
Exynos code (USB DRDx).
BRANCH=None
BUG=chrome-os-partner:54621
TEST=Plug a USB 3.0 Patriot Memory stick into both ports in all
orientations, observe how it gets reliably detected now (safe for some
known hardware issues on my board).
Change-Id: Ifce6bcddd69f2e8f2e2a2f48faf65551e084da1e
Signed-off-by: Martin Roth <martinroth@chromium.org>
Original-Commit-Id: c526906f998bf66067d3addb8b3d3a126c188b1e
Original-Change-Id: Ie80a201a58764c4d851fe4a5098a5acfc4bcebdf
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/366160
Original-Reviewed-by: liangfeng wu <wulf@rock-chips.com>
Original-Reviewed-by: Shelley Chen <shchen@chromium.org>
Original-Reviewed-by: <515506667@qq.com>
Reviewed-on: https://review.coreboot.org/16125
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Prior to this patch, time->wday was not being initialized in rtc_get(),
but was still being used by rtc_display() to print a day.
Set to -1 which gets printed as "unknown ".
Fixes coverity issue 1357459 - Uninitialized scalar variable
Change-Id: Idecb7968f854df997b58a342e1a06a879f299394
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/15899
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
We were using the wrong register when reading the obs value and setting
the DQS driver. This did not affect LPDDR3 performance, but still needs
to be fixed.
BUG=none
BRANCH=none
TEST=boot from kevin
Change-Id: I144f575e27fba11872a8c5463ab1e2986f385ede
Signed-off-by: Martin Roth <martinroth@chromium.org>
Original-Commit-Id: 98221e6b03fc09cbf62af29a270e7a8aa8dfb986
Original-Change-Id: Ie179f9a2955c5712951d40b3ada9c14a51c09c8d
Original-Signed-off-by: Lin Huang <hl@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/363170
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/16052
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Coming Kevin revisions will switch back to an I2C TPM. This patch adds
the required configuration options and code to support that. Since the
TPM type can currently only be changed at compile time, we can no longer
support older Kevins with the same image. In order to build for Kevin
revisions < 5, you have to explicitly override the CONFIG_GRU_HAS_TPM2.
BRANCH=None
BUG=chrome-os-partner:55523
TEST=Compiled both Kevin and Gru, confirmed that bootblock and verstage
binary had the appropriate code differences.
Change-Id: I1b2abe0f331eb103eb0a84f773ee7521d31ae5d8
Signed-off-by: Martin Roth <martinroth@chromium.org>
Original-Commit-Id: 3245bff937154f0f9f39894de9c98a75631d59d9
Original-Change-Id: I81a15c9fb037a7ca2d69818e46cbb4f9a5ae1989
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/364222
Original-Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-on: https://review.coreboot.org/16029
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins)
|
|
When enabling the controller ODT, the controller vref needs to
correspond with the ODT value and DQ drive strength.
BRANCH=none
BUG=chrome-os-partner:54871
TEST=run "stressapptest -M 1024 -s 1000" on kevin board and pass
Original-Commit-Id: a7251c72b87d9f149b68d086c3252f1c668e0e80
Original-Change-Id: I7e54b3473f68a382208a0fb0b0600552fe6390ad
Original-Signed-off-by: Lin Huang <hl@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/358762
Original-Commit-Ready: Dan Shi <dshi@chromium.org>
Original-Tested-by: Caesar Wang <wxt@rock-chips.com>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Squashed with:
rockchip/rk3399: Halt if we get an invalid odt or drv value
When we were pushing the updated sdram.c to coreboot.org, the compiler
there found that we were not initializing vref_value_dq in all code
possible code paths.
This patch updates those code paths to halt the system.
Branch=none
Bug=none
Test=Built with coreboot.org toolchain and verified that the compile
errors were gone.
Change-Id: I0ad4207dc976236d64b6cdda58d10bcfbe1fde11
Signed-off-by: Martin Roth <martinroth@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/362726
Reviewed-by: Julius Werner <jwerner@chromium.org>
Change-Id: I22a0cef6f12d9aae2ea4dcb99e7ebdd788f2cdd1
Signed-off-by: Martin Roth <martinroth@chromium.org>
Reviewed-on: https://review.coreboot.org/15812
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
As shown in testing, if CA use 34.3ohms drive strength, it leads
to an overshoot. To fix this, change the drive strength to 48 ohms.
BRANCH=none
BUG=chrome-os-partner:54871
TEST=run "stressapptest -M 1024 -s 1000" on kevin board and pass
Change-Id: I8666474fc18391da14a3338611f962f2f08f36d0
Signed-off-by: Martin Roth <martinroth@chromium.org>
Original-Commit-Id: fbc1c13f9ab808fc907b2e3f9bde1d09f92980f1
Original-Change-Id: I231f5b1bd45ff262686fbacbaf119a8a57fad27b
Original-Signed-off-by: Lin Huang <hl@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/358761
Original-Commit-Ready: Dan Shi <dshi@chromium.org>
Original-Tested-by: Caesar Wang <wxt@rock-chips.com>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/15811
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
The 'speed' variable isn't being used after refactoring.
Change-Id: Id27a920c61b2bba18d391a7bfefe570235402dec
Signed-off-by: Martin Roth <martinroth@chromium.org>
Reviewed-on: https://review.coreboot.org/15749
Tested-by: build bot (Jenkins)
Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Asserting this GPIO will send a signal to the EC to trigger a reset
for the AP and the CR50.
BRANCH=none
BUG=chrome-os-partner:55252
TEST=the device now reboots when it needs to switch between different
boot modes instead of hanging with "failed to reboot" message.
Change-Id: I8d168e313b6983c96c80f7ad6d70bb84c1ec1d9c
Signed-off-by: Martin Roth <martinroth@chromium.org>
Original-Commit-Id: 83a4c8ff68ab24a103f2166e948eb23624ea97f7
Original-Change-Id: Idfd20977cf3682bd8933f89e8eec53005e55864e
Original-Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/360238
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/15718
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins)
|
|
rk3399 sdram size is 192K, and there still some unused space.
We need more romstage space to include the sdram config, so extend
the romstage range.
BRANCH=none
BUG=chrome-os-partner:54871
TEST=run "stressapptest -M 1024 -s 1000" on kevin board and pass
Change-Id: Ib827345fe646e985773e6ce3e98ac3f64317fffb
Signed-off-by: Martin Roth <martinroth@chromium.org>
Original-Commit-Id: 626ab15bb4ebb004d5294b948bbdecc77a72a484
Original-Change-Id: Ib5aa1e1b942cde8d9476773f5a84ac70bb830c80
Original-Signed-off-by: Lin Huang <hl@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/359092
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/15660
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
kevin rev3 pwm regulator ripple is still not great, especially for
center logic. To make sdram at 800MHz stable, raise it to 0.95v.
BRANCH=none
BUG=chrome-os-partner:54871
TEST=run "stressapptest -M 1024 -s 1000" on kevin board and pass
Change-Id: If4a15eb7398eea8214cb58422bca7cfb5f4a051a
Signed-off-by: Martin Roth <martinroth@chromium.org>
Original-Commit-Id: d29bc581effb0008eb196685aa22dd65b5d478a5
Original-Change-Id: Ideec9c3ab2f919af732719ed2f6a702068d99c8f
Original-Signed-off-by: Lin Huang <hl@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/359130
Original-Commit-Ready: Douglas Anderson <dianders@chromium.org>
Original-Reviewed-by: Douglas Anderson <dianders@chromium.org>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/15659
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This removes an empty function for sdram training. If it's needed
later, we can always add it back.
BRANCH=none
BUG=none
TEST=build and boot firmware for kevin/gru
Change-Id: Id526ef86cf5044894a1a736cc39f10d32f49c072
Signed-off-by: Martin Roth <martinroth@chromium.org>
Original-Commit-Id: 3e93461b96bfadc08bf0b46cf99052d9cdffa422
Original-Change-Id: I6bf77d2f81719c68cd78722c3fe9ae547ea1e79c
Original-Signed-off-by: Derek Basehore <dbasehore@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/354164
Original-Reviewed-by: Martin Roth <martinroth@chromium.org>
Reviewed-on: https://review.coreboot.org/15657
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This changes the src arg for copy_to_reg to a const u32 * instead of a
u32 * in sdram.c.
BRANCH=none
BUG=none
TEST=emerge-gru coreboot
Change-Id: I80f49258b2f8102f0d988fec85b8038a00e18a34
Signed-off-by: Martin Roth <martinroth@chromium.org>
Original-Commit-Id: e0342e5c0181bf65ae78aa9518b0d6bd6cb1d5ec
Original-Change-Id: I362727f1dbe6726bf3240f9219c394786162a1a0
Original-Signed-off-by: Derek Basehore <dbasehore@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/354163
Original-Reviewed-by: Martin Roth <martinroth@chromium.org>
Original-Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/15656
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This simplifies some of the code with better variable declaractions
which removes a lot of line continuations. Instead of declaring a
pointer to the container of the needed struct or array, this retrieves
a pointer to the struct or array instead.
BRANCH=none
BUG=none
TEST=check that gru and kevin still build and boot properly followed
by running "stressapptest -M 1024 -s 1000" and making sure it passes
Change-Id: I34a9be0f35981c03a6b0c27a870981a5f69cecc0
Signed-off-by: Martin Roth <martinroth@chromium.org>
Original-Commit-Id: 5c17449fcdfbe83ec75a3a006aaf7393c66006b7
Original-Change-Id: If4e386d4029f17d811fa3ce83e5be89e661a7b11
Original-Signed-off-by: Derek Basehore <dbasehore@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/354162
Original-Reviewed-by: Martin Roth <martinroth@chromium.org>
Original-Reviewed-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: https://review.coreboot.org/15655
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This removes a variable that was only used once and makes variable
declarations consistent by moving those only used in one block of code
into that block.
BRANCH=none
BUG=none
TEST=on kevin/gru, run "stressapptest -M 1024 -s 3600"
Change-Id: Iacfc0ffef34a4953cfb304b8cb4975b045aea585
Signed-off-by: Martin Roth <martinroth@chromium.org>
Original-Commit-Id: a79bbbc83d0f5cccf6bb4ad44ae2239c7f4b45e3
Original-Change-Id: Id0ff0c45189c292ab40e1c4aa27929fb7780e864
Original-Signed-off-by: Derek Basehore <dbasehore@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/355667
Original-Reviewed-by: Martin Roth <martinroth@chromium.org>
Original-Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/15654
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This adds two local variables for dramtype and ddr_freq to sdram_init
since those two values are commonly used in the function. It also
removes a variable that is just used once and directly uses the value
for a function call instead.
BRANCH=none
BUG=none
TEST=on kevin/gru, run "stressapptest -M 1024 -s 3600" and check that
it passes
Change-Id: I4e9dbc97803ff3300b52a5e1672e7e060af2cc85
Signed-off-by: Martin Roth <martinroth@chromium.org>
Original-Commit-Id: b7d1135c65298a73e6bf2a4a34b7c9b84f249ea8
Original-Change-Id: I4e1a1a4a8848d0eab07475a336c24bda90b2c9f8
Original-Signed-off-by: Derek Basehore <dbasehore@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/355666
Original-Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/15653
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
With recent bootblock code additions the CBMEM console buffer is not
large enough to store the entire log accumulated before DRAM is
initialized, spilling 700 bytes or so on the floor.
This patch adds 1 KB to the CBMEM console buffer, at the expense of the
bootblock area in SRAM. The bootblock is taking less then 26K out of
31K allocated for it after this change.
Placing CBMEM console area right after the bootblock makes sure other
memory regions are not going to be affected should memory distribution
between bootblock and CBMEM console need to change again.
BRANCH=none
BUG=none
TEST=examining /sys/firmware/log after device boots up into Chrome OS
does not report truncated console buffer any more.
Change-Id: I016460f57c70dab4d603d4c5dbfc5ffbc6c3554f
Signed-off-by: Martin Roth <martinroth@chromium.org>
Original-Commit-Id: bfa31684a1a9be87f39143cb6c07885a7b2e4843
Original-Change-Id: I2c3d198803e6f083ddd1d8447aa377ebf85484ce
Original-Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/358125
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/15607
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
The pull bias settings for GPIO0_A, GPIO0_B, GPIO2_C and GPIO2_D
are different from the other GPIO banks.
This patch adds a callback function to get the GPIO pull value
of each SoC(rk3288 and rk3399) so we can still use the common
GPIO driver.
BRANCH=none
BUG=chrome-os-partner:53251
TEST=Jerry and Gru still boot
Change-Id: I2a00b7ffd2699190582f5f50a1e21b61c500bf4f
Signed-off-by: Martin Roth <martinroth@chromium.org>
Original-Commit-Id: 46d5fa7297693216a2da9bcf15ccce4af796e80e
Original-Change-Id: If53f47181bdc235a1ccfefeeb2a77e0eb0e3b1ca
Original-Signed-off-by: Shunqian Zheng <zhengsq@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/358110
Original-Commit-Ready: Julius Werner <jwerner@chromium.org>
Original-Tested-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/15587
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
coreboot boots from the little core, and doesn't use the big core for
now, but if apll_b is set to the default 24MHz, it will take a long time
to enable the big core. This will cause a watchdog crash, so apll_b
initialization to 600MHz needs to be done in coreboot.
BRANCH=none
BUG=chrome-os-partner:54817
TEST=Pick CL:353762 and see big CPU clocks look right
TEST=Boot from Gru and see no cpufreq warnings
Change-Id: Ie45cd2271555942e4321e9a9e523dc10f63d8107
Signed-off-by: Martin Roth <martinroth@chromium.org>
Original-Commit-Id:
Original-Change-Id: I20b8b591db3171e27740d85edce11f9e8797d849
Original-Signed-off-by: Martin Roth <martinroth@chromium.org>
Original-Original-Commit-Id: 16bc916174042620bebe19ae73d241002491aecc
Original-Original-Change-Id: Id3487138b383b6643ba7e3ce1eae501a6622da10
Original-Original-Signed-off-by: Lin Huang <hl@rock-chips.com>
Original-Original-Signed-off-by: Douglas Anderson <dianders@chromium.org>
Original-Original-Reviewed-on: https://chromium-review.googlesource.com/356399
Original-Original-Reviewed-by: Vadim Bendebury <vbendeb@chromium.org>
Original-Original-Tested-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: https://review.coreboot.org/15583
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Use the apll define instead of the apll_l define so it can be reused
when setting apll_b.
BRANCH=None
BUG=None
TEST=Boot from Gru
Change-Id: Iebc4ce3b66a86c33653292340b9855265ac4fc07
Signed-off-by: Martin Roth <martinroth@chromium.org>
Original-Commit-Id: eb578110d19a35ef04f8749fdc202055abd50fd1
Original-Change-Id: I63966e98af48eaf49837eb0b781eea001a376ef4
Original-Signed-off-by: Lin Huang <hl@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/356398
Original-Reviewed-by: Douglas Anderson <dianders@chromium.org>
Original-Tested-by: Douglas Anderson <dianders@chromium.org>
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Original-Commit-Queue: Douglas Anderson <dianders@chromium.org>
Reviewed-on: https://review.coreboot.org/15582
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Currently aclkm pclkdbg atclk clocks use apll_l as a parent, but the
apll_l frequency may change in firmware, so we need to caculate the div
value based on the apll_l frequency.
BRANCH=None
BUG=chrome-os-partner:54376
TEST=Boot from Gru
Change-Id: I2bd8886168453ce98efec58b5490c2430762769b
Signed-off-by: Martin Roth <martinroth@chromium.org>
Original-Commit-Id: 116ae863a504630e2aff056564836d84198fcae2
Original-Change-Id: I7e3a5d9e3f608ddf15592d893117c92767fcd015
Original-Signed-off-by: Lin Huang <hl@rock-chips.com>
Original-Signed-off-by: Douglas Anderson <dianders@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/356397
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/15581
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Cleans up the comments in sdram.c to make them consistent.
BRANCH=none
BUG=none
TEST=make sure gru/kevin build and boot
also, run "stressapptest -M 1024 -s 3600" to make sure it passes
Change-Id: I1daf72b847374d549389bacd2fa0a9f8f231b190
Signed-off-by: Martin Roth <martinroth@chromium.org>
Original-Commit-Id: 63a224d6f4b0e4d13bc372c05c4b9196895d553f
Original-Change-Id: Iaf8a32cfe2b22c4ccff71952f90d162ad8c2d3e7
Original-Signed-off-by: Derek Basehore <dbasehore@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/355665
Original-Reviewed-by: Martin Roth <martinroth@chromium.org>
Reviewed-on: https://review.coreboot.org/15579
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
The name must not terminated with a newline character `\n` as it would
make it hard to use it strings. So, remove the newline from the two SoCs
with it.
Change-Id: I7570442b38a455e7c497d7f461c208fb0a88296d
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: https://review.coreboot.org/15540
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
This is a purely cosmetic change replacing some of the more prominent
copy and paste sections of the code with compressed versions of the
same.
BRANCH=none
BUG=none
TEST=with the rest of the patches applied stressapptest still runs for
an hour on both Kevin and Gru.
Change-Id: I492e1898e312473d07d9e5eceb3e3e10b48ee35f
Signed-off-by: Martin Roth <martinroth@chromium.org>
Original-Commit-Id: eb8043f96457d090dbbee57097bc1d685e7d32d2
Original-Change-Id: I362e0e261209ae4d4890ecb0e08bb1956c172ffd
Original-Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/353774
Original-Reviewed-by: Derek Basehore <dbasehore@chromium.org>
Reviewed-on: https://review.coreboot.org/15308
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
After write leveling for all ranks, check the
PHY_CLK_WRDQS_SLAVE_DELAY result, if the two ranks in one slice both
meet (0x200-PHY_CLK_WRDQS_SLAVE_DELAY < 0x20) or
(0x200-PHY_CLK_WRDQS_SLAVE > 0x1E0), enable PHY_WRLVL_EARLY_FORCE_ZERO
for this slice, and trigger write leveling again.
BRANCH=none
BUG=chrome-os-partner:54144
TEST=run "stressapptest -M 1024 -s 1000" and pass
Change-Id: I1a0e4e888eb62b5fae5b5e5437a385e8660a246d
Signed-off-by: Martin Roth <martinroth@chromium.org>
Original-Commit-Id: 717cbac97b2045f2934e99859ce405aa3637b1c4
Original-Change-Id: Ic0d7c59404e870a7108ed64bbf3215fcc2d0973e
Original-Signed-off-by: Lin Huang <hl@rock-chips.com>
Original-Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/351825
Reviewed-on: https://review.coreboot.org/15300
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
The CENTER LOGIC should always be 0.9V and can not be adjusted,
so use duty_ns = 2860 to correct CENTER LOGIC to 0.9V. And now
DDR seems to run stable at 800MHz on the gru board.
BRANCH=none
BUG=chrome-os-partner:54144, chrome-os-partner:53208
TEST=run "stressapptest -M 1024 -s 1000" and pass
Change-Id: Ia900e248c10ddd0ab630446a324cc0446c0fa49b
Signed-off-by: Martin Roth <martinroth@chromium.org>
Original-Commit-Id: f4fb1cefb59ac4099cef8b32a68ed9222e708478
Original-Change-Id: I2238da6c17908d09bc284b321d796901317ed9ef
Original-Signed-off-by: Lin Huang <hl@rock-chips.com>
Original-Signed-off-by: Douglas Anderson <dianders@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/352772
Reviewed-on: https://review.coreboot.org/15297
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This register is described in the TRM in section called
GRF_GPIO3D_IOMUX. Added definitions allow to configure the SPI0
interface.
BRANCH=none
BUG=chrome-os-partner:50645, chrome-os-partner:51537
TEST=with the rest of the patches applied it is possible to
communicate over SPI0
Change-Id: Ieee3fcae6095020042b02673c7d863f398ed2eb4
Signed-off-by: Martin Roth <martinroth@chromium.org>
Original-Commit-Id: 8f155e3b47c9f44ad4e5a2513916572e7d5ec0ab
Original-Change-Id: Iea92971b0520dc4549cd0fd263dcb2098f80f6d6
Original-Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/349851
Original-Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-on: https://review.coreboot.org/15295
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
