summaryrefslogtreecommitdiff
path: root/src/soc/mediatek
AgeCommit message (Collapse)Author
2019-10-23soc/mediatek/mt8183: fine tune the phy timingJitao Shi
To fix MIPI D-PHY test failure, the hs-prepare should be less than LimitMin from spec, and we have to enlarge TEOT margin. BUG=b:138344447 BRANCH=kukui TEST=Boots correctly on kukui Change-Id: If91e7a546866299f02432be27fe778be5d7bdc5f Signed-off-by: Jitao Shi <jitao.shi@mediatek.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/36222 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Hung-Te Lin <hungte@chromium.org>
2019-10-21src/{device,drivers,mb,nb,soc,sb}: Remove unused 'include <console/console.h>'Elyes HAOUAS
Change-Id: I0c965e598e260ff8129aa07fb9fc5bf6e784e1d8 Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/c/coreboot/+/36057 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
2019-10-21soc/mediatek/mt8183: Force DRAM retraining if hotkey pressedYu-Ping Wu
Similar to MRC cache on x86 platforms, when a hotkey is pressed during boot, the calibration data cache saved in the flash will be cleared, consequently triggering DRAM retraining (full calibration) in the next boot. BRANCH=kukui BUG=b:139099592 TEST=emerge-kukui coreboot Change-Id: I2f9225f359e1fe5733e8e1c48b396aaeeb9a58ab Signed-off-by: Yu-Ping Wu <yupingso@chromium.org> Reviewed-on: https://review.coreboot.org/c/coreboot/+/36090 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Hung-Te Lin <hungte@chromium.org>
2019-10-21soc/mediatek/mt8183: Skip fast calibration in recovery modeYu-Ping Wu
SoC DRAM team suggested always running full calibration mode in recovery mode because it is possible to get unstable memory even if the complex memory test has been passed. Since the recovery mode runs from RO and we only have training data cache for RW, the trained calibration data can't be saved since RO and RW may be running different firmware. Also revised few message to make it more clear for what calibration mode (fast, full, or partial) has been executed. BRANCH=kukui BUG=b:139099592 TEST=emerge-kukui coreboot Change-Id: I29e0df71dc3357462e15ce8fc2ba02f21b54ed33 Signed-off-by: Yu-Ping Wu <yupingso@chromium.org> Reviewed-on: https://review.coreboot.org/c/coreboot/+/36089 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Hung-Te Lin <hungte@chromium.org>
2019-10-20src: Remove unused 'include <string.h>'Elyes HAOUAS
Change-Id: I2a94c3b6282e9915fd2b8136b124740c8a7b774c Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/c/coreboot/+/36082 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
2019-10-18soc/mediatek/mt8183: Compress calibration blob with LZ4Hung-Te Lin
The DRAM calibration blob can be compressed using pre-RAM algorithm (currently LZ4), which will save ~12ms in boot time. On Kodama, boot time difference: Before: 1,082,711 After: 1,070,309 BUG=b:139099592,b:117953502 TEST=build and boot, cbfstool coreboot.rom print -v (see dram compressed) BRANCH=kukui Change-Id: Ic3bd49d67ee6f80a0e4d8f6945744642611edf64 Signed-off-by: Hung-Te Lin <hungte@chromium.org> Reviewed-on: https://review.coreboot.org/c/coreboot/+/36054 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Yu-Ping Wu <yupingso@google.com> Reviewed-by: Julius Werner <jwerner@chromium.org>
2019-10-18soc/mediatek/mt8183: Pass impedance data as a function argumentYu-Ping Wu
To make data flow more explicit, global variable 'impedance' is replaced with a local variable, which is passed as a function argument. BUG=none BRANCH=kukui TEST=Krane boots correctly Change-Id: I0f6dacc33fda013a3476a10d9899821b7297e770 Signed-off-by: Yu-Ping Wu <yupingso@chromium.org> Reviewed-on: https://review.coreboot.org/c/coreboot/+/35766 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Hung-Te Lin <hungte@chromium.org>
2019-10-18soc/mediatek/mt8183: Run calibration with multiple frequencies for DVFS switchHuayang Duan
The patch adds config MT8183_DRAM_DVFS to enable DRAM calibration with multiple frequencies to support DVFS switch. BUG=b:80501386,b:142358843 BRANCH=kukui TEST=Boots correctly on Kukui Change-Id: I97c8e513dc3815a2d62b2904a246a1d8567704a4 Signed-off-by: Yu-Ping Wu <yupingso@chromium.org> Reviewed-on: https://review.coreboot.org/c/coreboot/+/35555 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Hung-Te Lin <hungte@chromium.org>
2019-10-18soc/mediatek/mt8183: Adjust DRAM voltages for each DRAM frequencyHuayang Duan
This patch supports voltage adjustment for each DRAM frequency, which is neccesary to support DVFS switch. BUG=b:80501386,b:142358843 BRANCH=none TEST=Boots correctly and stress test pass on Kukui. Change-Id: I9539473ff708f9d0d39eb17bd3fdcb916265d33e Signed-off-by: Huayang Duan <huayang.duan@mediatek.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/35017 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Hung-Te Lin <hungte@chromium.org>
2019-10-18soc/mediatek/mt8183: Allow modifying vddq voltageHsin-Hsiung Wang
DRAM DVFS needs to be calibrated with different vddq voltages to get correct parameters. A new API is added to allow changing vddq voltage. BUG=b:80501386 BRANCH=none TEST=measure vddq voltage with multimeter Change-Id: I5f0d82596a1709bf0d37885f257646133f18f210 Signed-off-by: Hsin-Hsiung Wang <hsin-hsiung.wang@mediatek.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/35147 Reviewed-by: Hung-Te Lin <hungte@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2019-10-18soc/mediatek/mt8183: Allow modifying vdram1 voltageHsin-Hsiung Wang
DRAM DVFS needs to be calibrated with different vdram1 voltages to get correct parameters. A new API is added to allow changing vdram1 voltage. BUG=b:80501386 BRANCH=none TEST=measure vdram1 voltage with multimeter Change-Id: Ia15ab3a2e1668e5b4873d317b57a38ebee037709 Signed-off-by: Hsin-Hsiung Wang <hsin-hsiung.wang@mediatek.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/33186 Reviewed-by: Hung-Te Lin <hungte@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2019-10-18soc/mediatek/mt8183: Share console for calibration blob outputHung-Te Lin
Most coreboot debug messages are sent to UART and cbmem console, and we also want to collect DRAM calibration module output, especially for cbmem console (so we can see the logs after kernel is up). Instead of sharing whole cbmem/cbtable/cbmemconsole implementations, we want to simplify that by a simple function pointer so output can be preserved by do_putchar, which internally sends data to all registered consoles (usually cbmem console and UART). BUG=b:139099592 TEST=make; boots properly for full-k, with and without serial console. BRANCH=kukui Change-Id: I1cf16711caf3831e99e17b522b86694524425116 Signed-off-by: Hung-Te Lin <hungte@chromium.org> Reviewed-on: https://review.coreboot.org/c/coreboot/+/36056 Reviewed-by: Julius Werner <jwerner@chromium.org> Reviewed-by: Yu-Ping Wu <yupingso@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2019-10-17soc/mediatek/mt8183: Verify checksum of cached calibration dataYu-Ping Wu
The checksum is stored in the header of calibration data and saved to SPI flash. After reading the data from flash, checksum is used to verify the integrity of the calibration parameters. BUG=b:139099592 BRANCH=kukui TEST=Calibration data successfully loaded from flash Change-Id: Ie4a0688ed6e560d4c0c6b316f44e52fd10d71a9d Signed-off-by: Yu-Ping Wu <yupingso@chromium.org> Reviewed-on: https://review.coreboot.org/c/coreboot/+/36014 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Hung-Te Lin <hungte@chromium.org>
2019-10-17soc/mediatek/mt8183: Remove unnecessary DRAM register settingsYu-Ping Wu
In broadcast mode we only need to set registers for channel 0 instead of all channels. BUG=none BRANCH=kukui TEST=emerge-kukui coreboot Change-Id: I22a4b69fd40d1978fa7b12e8edaba00ce5d7787d Signed-off-by: Yu-Ping Wu <yupingso@chromium.org> Reviewed-on: https://review.coreboot.org/c/coreboot/+/36075 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Hung-Te Lin <hungte@chromium.org>
2019-10-17soc/mediatek/mt8183: Fix DDR phy config numberYu-Ping Wu
Some typos are fixed to make DVFS switch work. BUG=b:142358843 BRANCH=kukui TEST=emerge-kukui coreboot Change-Id: I064d4a2c46187ac5780352da742bd56e82c22c14 Signed-off-by: Yu-Ping Wu <yupingso@chromium.org> Reviewed-on: https://review.coreboot.org/c/coreboot/+/36074 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Hung-Te Lin <hungte@chromium.org>
2019-10-17soc/mediatek/mt8183: Refactor DRAM init by bit fields APIHung-Te Lin
Replace the magic clrsetbits_le32, read32, write32 by SET_BITFIELDS and other bit field helpers. Change-Id: I327297dd10718fbef7275fe95c95d00d3ab6ac84 Signed-off-by: Hung-Te Lin <hungte@chromium.org> Reviewed-on: https://review.coreboot.org/c/coreboot/+/35471 Reviewed-by: Julius Werner <jwerner@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2019-10-17soc/mediatek/mt8183: Improve code formattingYu-Ping Wu
This patch contains some minor changes including: - Use lowercase hex literals - Combine short lines - Remove unnecessary curly braces - Simplify struct initialization - Leverage macro _SELPH_DQS_BITS - Ensure whitespaces around binary operators - Remove extra whitespaces after commas - Change log level and remove unnecessary debug logs BUG=none BRANCH=kukui TEST=emerge-kukui coreboot Change-Id: I33616e6142325920c2fd7e6dc1dc88eb29c5cf34 Signed-off-by: Yu-Ping Wu <yupingso@chromium.org> Reviewed-on: https://review.coreboot.org/c/coreboot/+/36011 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Hung-Te Lin <hungte@chromium.org>
2019-10-17soc/mediatek/mt8183: Handle memory test failureYu-Ping Wu
If DRAM calibration fails or mem test fails using the cached calibration results stored in flash, rerun DRAM full calibration. If partial calibration fails or the mem test following it fails, hang forever. Partial calibration acts as a fallback approach in case of full calibration failure. Therefore, if it fails, there would be no other ways to initialize DRAM. Instead of falling into reboot loop and draining out of battery, it is better to just hang so that the end user may notice that and send to RMA. BUG=b:80501386,b:139099592 BRANCH=kukui TEST=Boots correctly on Kukui Change-Id: I8e1d4f5bc7b45f45a8bfef74e86ec0ff6a556af4 Signed-off-by: Huayang Duan <huayang.duan@mediatek.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/35481 Reviewed-by: Hung-Te Lin <hungte@chromium.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2019-10-09soc/mediatek/mt8183: Change argument type of mt_set_emiYu-Ping Wu
Since struct dramc_param has been defined, we can pass the struct directly from mt_mem_init(). BUG=b:139099592 BRANCH=none TEST=emerge-kukui coreboot Change-Id: If7333fb579eff76dd9d1c2bf6fdfe7eccb22050f Signed-off-by: Yu-Ping Wu <yupingso@chromium.org> Reviewed-on: https://review.coreboot.org/c/coreboot/+/35846 Reviewed-by: Hung-Te Lin <hungte@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2019-10-09soc/mediatek/mt8183: Run DRAM full calibrationHuayang Duan
Load the calibration params from flash first and check the correctness of the params. If the params have correct format, perform DRAM fast calibration with these params to reduce bootup time. Otherwise, load the DRAM blob and perform DRAM full calibration. Bootup time of DRAM partial calibration: - 1,349,385 usecs with low frequency - 924,698 usecs with middle frequency - 1,270,089 usecs with high frequency 3,544,172 usecs in total. Bootup time of DRAM fast calibration: - 216,663 usecs with low frequency - 328,220 usecs with middle frequency - 322,612 usecs with high frequency 867,495 usecs in total. BUG=b:139099592 BRANCH=none TEST=emerge-kukui coreboot Change-Id: I8de29b14b1fb24b3b4f351c855c5c4d8f350cc34 Signed-off-by: Huayang Duan <huayang.duan@mediatek.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/35110 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Hung-Te Lin <hungte@chromium.org>
2019-10-09soc/mediatek/mt8183: Use cached calibration result for faster bootupHuayang Duan
Load calibration params from flash. If the format of the params is correct, use these calibration params for fast calibration to reduce the bootup time. Bootup time of DRAM partial calibration: - 1,349,385 usecs with low frequency - 924,698 usecs with middle frequency - 1,270,089 usecs with high frequency 3,544,172 usecs in total. Bootup time of DRAM fast calibration: - 216,663 usecs with low frequency - 328,220 usecs with middle frequency - 322,612 usecs with high frequency 867,495 usecs in total. BUG=b:139099592 BRANCH=none TEST=Boots correctly on Kukui Change-Id: I9ef4265dd369a1c276bb02294696556df927e7bc Signed-off-by: Huayang Duan <huayang.duan@mediatek.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/35164 Reviewed-by: Hung-Te Lin <hungte@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2019-10-09soc/mediatek/mt8183: Add the shared 'dramc_param' moduleYu-Ping Wu
The dramc_param module simplifies the communication between coreboot and MTK DRAM full calibration blob, and is shared by both implementations to ensure the same format of parameters. BUG=b:139099592 BRANCH=none TEST=emerge-kukui coreboot Change-Id: I4cfd634da1855a76706aab0b050197251e2ed4dd Signed-off-by: Yu-Ping Wu <yupingso@chromium.org> Reviewed-on: https://review.coreboot.org/c/coreboot/+/35775 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Hung-Te Lin <hungte@chromium.org>
2019-10-09soc/mediatek/mt8183: Simplify usage of dramc_engine2_endYu-Ping Wu
Since we always write to &ch[chn].ao.dummy_rd after calling dramc_engine2_end(), this write could be merged into dramc_engine2_end() to simplify code. BUG=none BRANCH=none TEST=emerge-kukui coreboot Change-Id: Ibb4bd5ed016118811ad2097098417c19f00f4263 Signed-off-by: Yu-Ping Wu <yupingso@chromium.org> Reviewed-on: https://review.coreboot.org/c/coreboot/+/35749 Reviewed-by: Hung-Te Lin <hungte@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2019-10-02mediatek/mt8183: Rename fields of struct sdram_paramsYu-Ping Wu
Two fields of struct sdram_params are renamed for future CL of DRAM full calibration. Field 'impedance' is also removed. BUG=none BRANCH=none TEST=emerge-kukui coreboot Change-Id: I2f9673fd5ea2e62ee971f0d81bdd12aaf565e31c Signed-off-by: Yu-Ping Wu <yupingso@chromium.org> Reviewed-on: https://review.coreboot.org/c/coreboot/+/35738 Reviewed-by: Hung-Te Lin <hungte@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2019-10-01mediatek/mt8183: Allow modifying vcore voltageHsin-Hsiung Wang
Because vcore is the power of ddrphy in the soc, DRAM DVFS needs to be calibrated with different vcore voltages to get correct parameters. A new API is added to allow changing vcore voltage. BUG=b:80501386 BRANCH=none TEST=measure vcore voltage with multimeter Change-Id: Ic43d5efe7e597121775dc853a3e2a08ebc59657d Signed-off-by: Hsin-Hsiung Wang <hsin-hsiung.wang@mediatek.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/33391 Reviewed-by: Hung-Te Lin <hungte@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2019-09-30mediatek/mt8183: Init SPM driverDawei Chien
To support mt8183 power saving during suspend to RAM, this patch loads SPM firmware to support SPM suspend. SPM needs its own firmware to do these power saving in the right timing under correct conditions. After linux PM suspends, SPM is able to turn off power for the last CPU and do more power saving for the SoC such as DRAM self-refresh mode and turning off 26M crystal. BUG=none BRANCH=none TEST=suspend/resume passes for LPDDR4 3200 Change-Id: I3393a772f025b0912a5a25a63a87512454fbc86e Signed-off-by: Dawei Chien <dawei.chien@mediatek.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/34545 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Yu-Ping Wu <yupingso@google.com> Reviewed-by: Hung-Te Lin <hungte@chromium.org>
2019-09-24mediatek/mt8183: Use different DRAM frequencies for eMCP DDRHuayang Duan
Devices using eMCP may run at a high DRAM frequency (e.g., 3600Mbps) while those with discrete DRAM can only run at 3200Mbps. This patch enables 3600Mbps for eMCP DDR for better system performance. BUG=b:80501386 BRANCH=none TEST=Boots correctly and stress test passes on Kukui Change-Id: Iab6a9c2c390feeb9497b051a255b29566909e656 Signed-off-by: Huayang Duan <huayang.duan@mediatek.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/34990 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Hung-Te Lin <hungte@chromium.org>
2019-09-20mediatek/mt8183: Support more DRAM frequency bootupHuayang Duan
Add more DRAM frequency bootup to support DRAM frequencies 1600Mbps, 2400Mbps, 3200Mbps and 3600Mbps. BUG=b:80501386 BRANCH=none TEST=Memory test passes on eMCP platform Change-Id: Ic1378ca43fb333c445ca77e7dc0844cdf65f2207 Signed-off-by: Huayang Duan <huayang.duan@mediatek.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/34332 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Patrick Georgi <pgeorgi@google.com>
2019-09-20mediatek/mt8183: Implement the dramc init settingHuayang Duan
This patch implements the dram init setting by replacing the hard-coded init sequence with a series of functions to support calibration for more frequencies. These functions are modified from MediaTek's internal DRAM full calibration source code. BUG=b:80501386 BRANCH=none TEST=1. Kukui boots correctly 2. Stress test (/usr/sbin/memtester 500M) passes on Kukui Change-Id: I756ad37e78cd1384ee0eb97e5e18c5461d73bc7b Signed-off-by: Huayang Duan <huayang.duan@mediatek.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/34988 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Hung-Te Lin <hungte@chromium.org>
2019-09-19cpu,mb,soc: Init missing lb_serial struct fieldsJacob Garber
Initialize the input_hertz and uart_pci_addr fields of the lb_serial struct to prevent later undefined reads in lb_add_serial(). This was done for exynos5420 in commit ff94e00362 (soc/samsung/exynos5420/uart.c: Init new serial struct variables), and this patch finishes the rest. Note that not all of the drivers can have the UART PCI address configured at build time, so a follow-up patch will be needed to correct those ones. Change-Id: I733bc8185e2f2d28a9823495b53d6b09dce4deb1 Signed-off-by: Jacob Garber <jgarber1@ualberta.ca> Found-by: Coverity CID 1354778 Reviewed-on: https://review.coreboot.org/c/coreboot/+/34548 Reviewed-by: Patrick Georgi <pgeorgi@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2019-09-16mediatek/mt8183: Add soc ARM Trusted Firmware supportkenny liang
Set BL31 platform to mt8183 to link with ARM Trusted Firmware. BUG=b:80501386 BRANCH=none Test=Boots correctly on Kukui with more patches in ATF. Change-Id: Ia988d2b4ed646027c04c7c6ff0e50ed7a0b14da3 Signed-off-by: kenny liang <kenny.liang@mediatek.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/29186 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Julius Werner <jwerner@chromium.org>
2019-09-14arm64: Uprev Arm TF and adjust to BL31 parameter changesJulius Werner
This patch uprevs the Arm Trusted Firmware submodule to the new upstream master (commit 42cdeb930). Arm Trusted Firmware unified a bunch of stuff related to BL31 handoff parameters across platforms which involved changing a few names around. This patch syncs coreboot back up with that. They also made header changes that now allow us to directly include all the headers we need (in a safer and cleaner way than before), so we can get rid of some structure definitions that were duplicated. Since the version of entry point info parameters we have been using has been deprecated in Trusted Firmware, this patch switches to the new version 2 parameter format. NOTE: This may or may not stop Cavium from booting with the current pinned Trusted Firmware blob. Cavium maintainers are still evaluating whether to fix that later or drop the platform entirely. Tested on GOOGLE_KEVIN (rk3399). Change-Id: I0ed32bce5585ce191736f0ff2e5a94a9d2b2cc28 Signed-off-by: Julius Werner <jwerner@chromium.org> Reviewed-on: https://review.coreboot.org/c/coreboot/+/34676 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Hung-Te Lin <hungte@chromium.org>
2019-09-10mediatek/mt8183: Add new option for eMCP DDRHuayang Duan
Devices using eMCP may run at a high DRAM frequency (e.g., 3600Mbs) while those with discrete DRAM can only run at 3200Mbps. A new option MT8183_DRAM_EMCP is added to Kconfig for a mainboard to select, depending on whether it supports eMCP or not. BUG=b:80501386 BRANCH=none TEST=Boots correctly on Kukui Change-Id: I9b73c8b512db5104896ea0d330d56e63eb50a44b Signed-off-by: Huayang Duan <huayang.duan@mediatek.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/34989 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Hung-Te Lin <hungte@chromium.org>
2019-09-06soc/mediatek: Fix USB enumeration issueChangqi Hu
Some USB 3.0 devices fail to be enumerated after USB reset, and xhci port status register shows the device is disconnected. After measuring the USB signal, we found that the USB disconnect threshold was lower and that the disconnect event was triggered unexpectedly. USB designers suggest changing discth to 15. BUG=b:122047652 TEST=emerge-kukui coreboot chromeos-bootimage Change-Id: I0e8556035b49d693a42cbe1099a6882a1c0ed0d1 Signed-off-by: Changqi Hu <changqi.hu@mediatek.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/35150 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Hung-Te Lin <hungte@chromium.org>
2019-09-04mediatek/mt8183: postpone dcxo low power mode settingWeiyi Lu
Consider the association between modem[1] and DCXO, this patch is a fix for eb5e47d("mediatek/mt8183: update dcxo output buffer setting") [2] We should not disable XO_CEL and block the bblpm request when modem is still ON. For power-saving, we still could disable unused XO_CEL and mask request to disable unused power mode when modem is no longer be used. [1] https://review.coreboot.org/c/coreboot/+/32666 [2] https://review.coreboot.org/c/coreboot/+/32323 BRANCH=none TEST=Boots correctly on Krane. Change-Id: I047ebed615e874977ca211aafd52b5551c71b764 Signed-off-by: Weiyi Lu <weiyi.lu@mediatek.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/34777 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Hung-Te Lin <hungte@chromium.org>
2019-09-02mediatek/mt8183: Remove unnecessary parenthesesYu-Ping Wu
Parentheses are unnecessary for conditions like '(a == b) || (c == d)'. Change-Id: I0c554bf1577b40286f7a51a8fc5804bdbb7c8bd1 Signed-off-by: Yu-Ping Wu <yupingso@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/35142 Reviewed-by: Julius Werner <jwerner@chromium.org> Reviewed-by: Huayang Duan <huayang.duan@mediatek.corp-partner.google.com> Reviewed-by: Angel Pons <th3fanbus@gmail.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2019-08-30arm64: Rename arm_tf.c/h to bl31.c/hJulius Werner
This patch renames arm_tf.c and arm_tf.h to bl31.c and bl31.h, respectively. That name is closer to the terminology used in most functions related to Trusted Firmware, and it removes the annoying auto-completion clash between arm64/arm_tf.c and arm64/armv8. Change-Id: I2741e2bce9d079b1025f82ecb3bb78a02fe39ed5 Signed-off-by: Julius Werner <jwerner@chromium.org> Reviewed-on: https://review.coreboot.org/c/coreboot/+/34677 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Hung-Te Lin <hungte@chromium.org>
2019-08-21mediatek/mt8183: add scp voltage initializationHsin-Hsiung Wang
Add scp voltage initialization. BUG=b:135985700 BRANCH=none Test=Boots correctly on Kukui and scp can boot up normally Change-Id: I5afb60af3c14490e20f28f1c089cfca42ddf7fcf Signed-off-by: Hsin-Hsiung Wang <hsin-hsiung.wang@mediatek.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/34205 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Yu-Ping Wu <yupingso@google.com> Reviewed-by: Hung-Te Lin <hungte@chromium.org>
2019-08-21mediatek/mt8183: Enlarge PRERAM_CBFS_CACHE regionTristan Shieh
Enlarge PRERAM_CBFS_CACHE region from (16K - 4) to (48K - 4) bytes to decompress and load more data from CBFS in romstage. BUG=b:134351649 BRANCH=none TEST=emerge-kukui coreboot Change-Id: Idc23a67c886718e910ca3c50468e5793f19c8d66 Signed-off-by: Tristan Shieh <tristan.shieh@mediatek.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/34896 Reviewed-by: Hung-Te Lin <hungte@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2019-08-21mediatek/mt8183: Overlap decompressor, verstage and romstageTristan Shieh
Since SRAM space is too small to fit all needed features, enable VBOOT_RETURN_FROM_VERSTAGE and overlap decompressor, verstage and romstage to gain more space. BUG=b:134351649 BRANCH=none TEST=emerge-kukui coreboot Change-Id: Ibe336cf93b01fa2ea57b4c2e0a89685424878c91 Signed-off-by: Tristan Shieh <tristan.shieh@mediatek.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/34871 Reviewed-by: Hung-Te Lin <hungte@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2019-08-21mediatek: Use GPIO based SPI CSYu-Ping Wu
Some boards (e.g., Kukui) need GPIO based CS for SPI0. This patch changes the pinmux and binds the pins to the correponding SPIs. When using GPIO based SPI CS, we need to manually make CS log/high before/after SPI transactions. BUG=b:132311067 BRANCH=none TEST=Verified that b/132311067 is irreproducible Change-Id: I61653fb19242b6ee6be9a45545a8b66e5c9c7cad Signed-off-by: Yu-Ping Wu <yupingso@chromium.org> Reviewed-on: https://review.coreboot.org/c/coreboot/+/33165 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Hung-Te Lin <hungte@chromium.org> Reviewed-by: Julius Werner <jwerner@chromium.org>
2019-08-20arch/non-x86: Remove use of __PRE_RAM__Kyösti Mälkki
Change-Id: Id8918f40572497b068509b5d5a490de0435ad50b Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/34921 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Julius Werner <jwerner@chromium.org>
2019-08-15soc/mediatek: Change DSI init commands to take flexible length arrayHung-Te Lin
The fixed size of init command in lcm_init_table is wasting lots of space and we should change to packed array since the command buffer already provides length information. With this change, BOE panel init commands have been reduced from 4848 bytes to 1309 bytes. BUG=b:80501386,b:117254947 TEST=emerge-kukui coreboot chromeos-bootimage; Boots properly Change-Id: I359dde8e6f2e1c0983f4677193bb47a7ae497ca6 Signed-off-by: Hung-Te Lin <hungte@chromium.org> Reviewed-on: https://review.coreboot.org/c/coreboot/+/34778 Reviewed-by: Julius Werner <jwerner@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2019-08-15soc/mediatek/mt8183: Add DSI driverHung-Te Lin
The MT8183 display serial interface (DSI) is based on MIPI Alliance Specification, supporting high-speed serial data transfer between host processor and peripheral devices such as display modules. DSI supports both video mode and command mode data transfer defined in MIPI spec, and it also provides bidirectional transmission with low-power mode to receive messages from the peripheral. Reference: MT8183 Application Processor Functional Spec, 6.7 Display Serial Interface (DSI) BUG=b:80501386,b:117254947 BRANCH=none TEST=Boots correctly on Kukui Change-Id: Ic413f524ca0b36f0b01f723a71fe9745e2710cd2 Signed-off-by: Jitao Shi <jitao.shi@mediatek.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/31591 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Julius Werner <jwerner@chromium.org>
2019-08-15soc/mediatek: dsi: Support sending MIPI init commandsHung-Te Lin
For systems with real MIPI panels (8173/oak was using PS8640 eDP bridge), we have to send DCS commands to initialize panel. BUG=b:80501386,b:117254947 TEST=make -j # board = oak and boots Change-Id: Ie7c824873465ac82a95bcb0ed67b8b9866987008 Signed-off-by: Hung-Te Lin <hungte@chromium.org> Reviewed-on: https://review.coreboot.org/c/coreboot/+/34773 Reviewed-by: Julius Werner <jwerner@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2019-08-15soc/mediatek: dsi: Refactor video timing calculationHung-Te Lin
The video timing should be based on PHY timing. Some values can be ignored on 8173 because of fixed values in PHY but should be calculated for newer platforms like 8183. BUG=b:80501386,b:117254947 TEST=make -j # board = oak and boots Change-Id: Id3ad2edc08787414a74188f5050460e98222caf4 Signed-off-by: Hung-Te Lin <hungte@chromium.org> Reviewed-on: https://review.coreboot.org/c/coreboot/+/34772 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Julius Werner <jwerner@chromium.org>
2019-08-14soc/mediatek: dsi: Refactor PHY timing calculationHung-Te Lin
The PHY timing should be calculated by data rate (Mbps). However for 8173 some values were hard-coded so we want to introduce a new mtk_phy_timing structure and a weak function mtk_dsi_override_phy_timing that allows per-SOC customization to apply PHY timings. BUG=b:80501386,b:117254947 TEST=make -j # board = oak and boots Change-Id: I1176ca06dda026029ff431aca7f9e21479eed670 Signed-off-by: Hung-Te Lin <hungte@chromium.org> Reviewed-on: https://review.coreboot.org/c/coreboot/+/34771 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Julius Werner <jwerner@chromium.org>
2019-08-13soc/mediatek: dsi: Refactor MIPI TX configurationHung-Te Lin
The only platform-specific difference in mtk_dsi_phy_clk_setting is how to configure MIPI TX because those registers (and logic) are quite different across different SOCs. The calculation of data rate is actually the same so we should isolate it and move to common, and rename mtk_dsi_phy_clk_setting to a better name as mtk_dsi_configure_mipi_tx. BUG=b:80501386,b:117254947 TEST=make -j # board = oak and boots Change-Id: I894dc2c4c053267debf5a58313b2bb489bcf5f3a Signed-off-by: Hung-Te Lin <hungte@chromium.org> Reviewed-on: https://review.coreboot.org/c/coreboot/+/34784 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Julius Werner <jwerner@chromium.org>
2019-08-13soc/mediatek: dsi: Unify format to bpp conversionHung-Te Lin
The 'bpp' was referred to both 'bits per pixel' and 'bytes per pixel' in MTK DSI driver and should be corrected. By this change we now always consider 'bpp' as 'bits per pixel', and rename the variables for other cases. BUG=b:80501386,b:117254947 TEST=make -j # board = oak and boots Change-Id: Ibd405220b73859e5592c68f498af07eef8d7edbc Signed-off-by: Hung-Te Lin <hungte@chromium.org> Reviewed-on: https://review.coreboot.org/c/coreboot/+/34770 Reviewed-by: Julius Werner <jwerner@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2019-08-13soc/mediatek: Create common DSI driver from mt8173Hung-Te Lin
The DSI initialization is almost the same for 8173 and 8183, so we want to move most of common functions into common/dsi.c. The major board-specific functions left are: - reset (controller register has different format) - pin_drv_ctrl (8183 does not need this) BUG=b:80501386,b:117254947 TEST=make -j # board=oak (mt8173) Change-Id: I8d4369a3c84db551287a9c9d1b22f552c5f7518d Signed-off-by: Hung-Te Lin <hungte@chromium.org> Reviewed-on: https://review.coreboot.org/c/coreboot/+/34769 Reviewed-by: Julius Werner <jwerner@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2019-08-09soc/mediatek/mt8183: Add display controller driverYongqiang Niu
The MT8183 SOC has a DISP (display controller) that supports overlay, read/write DMA, ... etc. The output of DISP goes to display interface DSI, DPI or DBI directly. Reference: MT8183 Application Processor Functional Spec, 6.1 Display Controller BUG=b:80501386,b:117254947 BRANCH=none TEST=Boots correctly on Kukui Change-Id: Ic4aecc58d081f14f5d136b9ff8e813e6f40f78eb Signed-off-by: Yongqiang Niu <yongqiang.niu@mediatek.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/31478 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Julius Werner <jwerner@chromium.org>
2019-08-09soc/mediatek/mt8173: Refactor display driver to share common partsHung-Te Lin
Move those will be shared by other MTK SOCs (for example, MT8183) to common/ddp.c. BUG=b:80501386,b:117254947 BRANCH=none TEST=Boots correctly on Oak Change-Id: Ie5709ab6e263caa21fdf7e799dc2ee884ffaf800 Signed-off-by: Yongqiang Niu <yongqiang.niu@mediatek.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/34515 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Julius Werner <jwerner@chromium.org>
2019-08-09soc/mediatek/mt8173: Remove dual DSI modeHung-Te Lin
The 'dual DSI mode' was never used by any real boards running coreboot and is introducing lots of complexity when it comes to refactoring. In order to create a common display stack for MTK SOCs, we want to first drop dual DSI mode so 8173 and 8183 DSI/DDP implementation will be more similar to each other. BUG=b:80501386,b:117254947 TEST=emerge-oak coreboot Change-Id: I357c30cc687803ca8045d0b055dec2e22eef4291 Signed-off-by: Hung-Te Lin <hungte@chromium.org> Reviewed-on: https://review.coreboot.org/c/coreboot/+/34693 Reviewed-by: Julius Werner <jwerner@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2019-08-07mediatek/mt8183: Add I2C driver codeQii Wang
This patch implements i2c driver for MT8183. BUG=b:80501386 BRANCH=none TEST=Boot correctly on kukui. Change-Id: I0a4d78b494819f45951f78e5a618021000cf3463 Signed-off-by: Qii Wang <qii.wang@mediatek.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/30976 Reviewed-by: Hung-Te Lin <hungte@chromium.org> Reviewed-by: Julius Werner <jwerner@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2019-08-02mediatek: Refactor I2C code among similar SOCsQii Wang
Refactor I2C code which will be reused among similar SOCs. BUG=b:80501386 BRANCH=none TEST=emerge-elm coreboot Change-Id: I407d5e2a9eb29562b40bb300e39f206a94afe76c Signed-off-by: qii wang <qii.wang@mediatek.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/30975 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Yu-Ping Wu <yupingso@google.com> Reviewed-by: Julius Werner <jwerner@chromium.org>
2019-07-26soc/mediatek/mt8183: Init SSPMErin Lo
Load SSPM firmware and boot up SSPM. BUG=b:80501386 BRANCH=none Test=We can see "SSPM is alive" in ATF stage if SSPM enabled and ipi success Change-Id: I9285034fc8ce38b40134f5eb7b986a663175e620 Signed-off-by: Erin Lo <erin.lo@mediatek.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/31835 Reviewed-by: Hung-Te Lin <hungte@chromium.org> Reviewed-by: Patrick Georgi <pgeorgi@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2019-07-25soc/mediatek: Use 'include <stdlib.h>' when appropriateElyes HAOUAS
Also including <types.h>, is supposed to provide stdint and stddef. Change-Id: Id6d881055826044d04843ba165641131b9111342 Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/c/coreboot/+/33690 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Julius Werner <jwerner@chromium.org>
2019-07-23mediatek/mt8183: Add md power-off flowYanjie Jiang
SRCCLKENA holds 26M clock, which will fail suspend/resume, and the SRCCLKENA is not used by mt8183, so we can simply release it for suspend/resume to work. BUG=b:80501386 BRANCH=none Test=Boots correctly on Kukui, suspend test pass. Change-Id: Ib6e11faeb6936a1dd6bbe8b1a8b612446bf51082 Signed-off-by: Yanjie.jiang <yanjie.jiang@mediatek.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/32666 Reviewed-by: Hung-Te Lin <hungte@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2019-07-22soc/mediatek/mt8183: Support SSPMErin Lo
SSPM is "Secure System Power Manager" that provides power control in secure domain. The initialization flow is to load SSPM firmware to its SRAM space and then enable. BUG=b:80501386 BRANCH=none Test=Build pass Change-Id: I4ae6034454326f5115cd3948819adc448b67fb1c Signed-off-by: Erin Lo <erin.lo@mediatek.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/31516 Reviewed-by: Julius Werner <jwerner@chromium.org> Reviewed-by: Hung-Te Lin <hungte@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2019-07-21mediatek/mt8183: Calibrate RTC eosc clockRan Bi
Calibrate RTC eosc clock which will be used when RTC goes into low power state. BUG=b:133872611 BRANCH=none TEST=Boots correctly on Kukui Change-Id: Ie8fd6f4cffdcf7cf410ce48343378a017923789c Signed-off-by: Ran Bi <ran.bi@mediatek.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/33907 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: You-Cheng Syu <youcheng@google.com> Reviewed-by: Hung-Te Lin <hungte@chromium.org>
2019-07-11mediatek: Fill in input_hertz to coreboot tableTristan Shieh
Set input_hertz to 26 MHz. BUG=b:134351649 BRANCH=none TEST=emerge-kukui coreboot; emerge-elm coreboot Change-Id: I7f9c329ae5d610f2516e60f06b2ac96ebbeaa897 Signed-off-by: Tristan Shieh <tristan.shieh@mediatek.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/34191 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Hung-Te Lin <hungte@chromium.org>
2019-07-09arch/non-x86: Flip HAVE_MONOTONIC_TIMER defaultKyösti Mälkki
Also remove allwinner/a10 dummy monotonic_timer implementation. Change-Id: I9dfa9b92dc63375465e3bb87b73eeefad601c810 Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/34112 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Nico Huber <nico.h@gmx.de>
2019-07-07mediatek/mt8183: update dcxo output buffer settingWeiyi Lu
DCXO consists of core that generates clock and output buffers that provide clock to other peripheral components. This patch mainly eliminates the extra power consumption of output buffers. We only enable the buffer for SOC and disable unused buffers for power-saving. Also disable useless buffer power mode to guarantee the lowest power state. BRANCH=none TEST=Boots correctly on Kukui. Change-Id: I2e5ce181ad327ccf852979da53baca4f249912fe Signed-off-by: Weiyi Lu <weiyi.lu@mediatek.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/32323 Reviewed-by: Julius Werner <jwerner@chromium.org> Reviewed-by: You-Cheng Syu <youcheng@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2019-07-06mediatek/mt8183: Enable RTC eosc calibration feature to save powerRan Bi
When system shuts down, RTC enable eosc calibration feature to save power. Then coreboot RTC driver needs to call rtc_enable_dcxo function at every boot to switch RTC clock source to dcxo. BUG=b:128467245 BRANCH=none TEST=Boots correctly on Kukui Change-Id: Iee21e7611df8959cbbc63b6e6655cfb462147748 Signed-off-by: Ran Bi <ran.bi@mediatek.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/32339 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Julius Werner <jwerner@chromium.org>
2019-06-21mediatek/mt8183: support SAMSUNG and MICRON EMCP LPDDR4X DDR bootupHuayang Duan
Support SAMSUNG KMDP6001DA-B425 and MICRON MT29VZZZAD8DQKSL EMCP LPDDR4X DDR From the calibration log of MICRON MT29VZZZAD8DQKSL, we found the begin pass range of RX window earlier than with other DDR type. So need change the DQS starting offset to increase the scan range of RX window. BUG=b:80501386 BRANCH=none TEST=Boots correctly on EMCP DRAM Change-Id: I5fcc8673a2fbd7ec3a8776ab61c57f8903ddda20 Signed-off-by: Huayang Duan <huayang.duan@mediatek.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/32243 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Hung-Te Lin <hungte@chromium.org> Reviewed-by: Julius Werner <jwerner@chromium.org> Reviewed-by: Huayang Duan <huayang.duan@mediatek.corp-partner.google.com>
2019-06-21mediatek/mt8183: fix mode register setting fail issueHuayang Duan
The mode register setting of DRAM may fail without some delay after each MR write. BUG=b:80501386 BRANCH=none TEST=Boots correctly and stress test pass on Kukui. Change-Id: I51785e90b2014994be5018bfe543245d44626242 Signed-off-by: Huayang Duan <huayang.duan@mediatek.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/32284 Reviewed-by: Hung-Te Lin <hungte@chromium.org> Reviewed-by: Huayang Duan <huayang.duan@mediatek.corp-partner.google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2019-06-21mediatek/mt8183: enable DDR low power featuremtk11195
BUG=b:80501386 BRANCH=none TEST=Boots correctly and stress test pass on Kukui. Change-Id: Ic48580e7e5db25dc1c29dabf41c4e3816fb946d3 Signed-off-by: Huayang Duan <huayang.duan@mediatek.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/32010 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Hung-Te Lin <hungte@chromium.org> Reviewed-by: Julius Werner <jwerner@chromium.org> Reviewed-by: Huayang Duan <huayang.duan@mediatek.corp-partner.google.com>
2019-06-21mediatek/mt8183: set vproc12 voltage correctlyHsin-Hsiung Wang
The correct address for vproc12 register of sw mode is 0x1426 instead of 0x140a. BUG=b:80501386 BRANCH=none Test=Boots correctly on Kukui and see that regulator is not stuck to 1.05V anymore: grep vproc12 /sys/kernel/debug/regulator/regulator_summary Change-Id: I13867b11c44019875e0ed607343197950a3b38b2 Signed-off-by: Hsin-Hsiung Wang <hsin-hsiung.wang@mediatek.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/33168 Reviewed-by: Hung-Te Lin <hungte@chromium.org> Reviewed-by: Nicolas Boichat <drinkcat@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2019-06-21mediatek/mt8183: Add infra group DCM settingWeiyi Lu
Add infra group DCM (Dynamic Clock Management) settings, which slows down OR gate clocks while hardware is in idle state. BUG=b:80501386 BRANCH=none TEST=Boots correctly on Kukui. Change-Id: I4741dfb7b984deb92171f370e5fb2593829d74c2 Signed-off-by: Weiyi Lu <weiyi.lu@mediatek.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/31977 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Julius Werner <jwerner@chromium.org> Reviewed-by: You-Cheng Syu <youcheng@google.com>
2019-06-21mediatek: Add SPI tick_dly settingMengqi Zhang
Add spi tick_dly setting for high-speed spi xfer. BUG=b:80501386 BRANCH=none TEST=emerge-kukui coreboot; emerge-elm coreboot Change-Id: Ie49fc3efe2a4a6dcdf2a2fc4c91b47e35d4f086e Signed-off-by: Mengqi Zhang <Mengqi.Zhang@mediatek.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/32461 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Julius Werner <jwerner@chromium.org>
2019-06-21mediatek/mt8183: Add SPI GPIO driving settingMengqi Zhang
Set SPI GPIO driving to support SPI FLASH. BUG=b:80501386 BRANCH=none TEST=emerge-kukui coreboot; emerge-elm coreboot Change-Id: I95002ec71abd751c33c089185db04ed4a8686699 Signed-off-by: Mengqi Zhang <Mengqi.Zhang@mediatek.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/32460 Reviewed-by: Hung-Te Lin <hungte@chromium.org> Reviewed-by: Julius Werner <jwerner@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2019-06-21mediatek/mt8183: Support RTC in ramstageYou-Cheng Syu
We need to support RTC in ramstage so that we can see correct timestamp in ChromiumOS eventlog. BUG=b:134461866 TEST='mosys eventlog list' shows correct timestamp on Kukui Change-Id: Idb0fe5c05e4ecdf0e6398e3c781c71d14f85f19b Signed-off-by: You-Cheng Syu <youcheng@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/33355 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Hung-Te Lin <hungte@chromium.org> Reviewed-by: Julius Werner <jwerner@chromium.org>
2019-06-21mediatek/mt8183: Add efuse calibration in auxadcjg_poxu
The values from auxadc may be incorrect if not calibrated by efuse. Without calibration, the value error range is about +/-50mv, and after being calibrated the error range is about +/-10mv. BUG=b:131391176 TEST=make clean && make test-abuild; boots on Kukui rev 2 units. BRANCH=none Change-Id: Iccd6ea0ad810c993f9b62c0974279c960f890e52 Signed-off-by: Po Xu <jg_poxu@mediatek.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/32800 Reviewed-by: Julius Werner <jwerner@chromium.org> Reviewed-by: JG Poxu <jg_poxu@mediatek.corp-partner.google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2019-06-21mediatek/mt8183: Calibrate vsim2 to 2.7 VHsin-Hsiung Wang
The default voltage of vsim2 is set to 2.76V for sim card usage. In general, 2.76V of vsim2 is composed of 2.7V main voltage and 0.06V calibration voltage. However, vsim2 is used for the tx_ovdd power of display port IT6505 on the kukui board design which needs 2.7V. So we set it to 2.7V with modifying calibration value. BUG=b:126139364 BRANCH=none TEST=measure vsim2 voltage with multimeter Change-Id: I4dffdde89cbde91286d92e6c2b445f0b3d0ad2fe Signed-off-by: Hsin-Hsiung Wang <hsin-hsiung.wang@mediatek.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/32057 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Julius Werner <jwerner@chromium.org>
2019-05-29src/soc: Add missing 'include <types.h>'Elyes HAOUAS
<types.h> is supposed to provide <stdint.h> and <stddef.h>. When <types.h> is included, <stdint.h> and/or <stddef.h> is removed. Change-Id: I2db0a647bc657a3626cb5e78f23e9198e290261a Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/c/coreboot/+/32810 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
2019-05-06mediatek/mt8183: Wait 200us for voltages to settleTristan Shieh
When we increase voltages, it takes 200us for voltages to stablize. BUG=b:80501386 BRANCH=none Test=Boots correctly on Kukui Change-Id: I5f32035693b6084dbe763411c612ae5d1f7c9e48 Signed-off-by: Tristan Shieh <tristan.shieh@mediatek.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/32498 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: You-Cheng Syu <youcheng@google.com> Reviewed-by: Julius Werner <jwerner@chromium.org>
2019-04-30vboot: refactor OPROM codeJoel Kitching
The name OPROM is somewhat inaccurate, since other steps to bring up display and graphics are needed depending on mainboard/SoC. This patch cleans up OPROM code nomenclature, and works towards the goal of deprecating vboot1: * Rename CONFIG_VBOOT_OPROM_MATTERS to CONFIG_VBOOT_MUST_REQUEST_DISPLAY and clarify Kconfig description * Remove function vboot_handoff_skip_display_init * Remove use of the VbInit oflag VB_INIT_OUT_ENABLE_DISPLAY * Add |flags| field to vboot_working_data struct * Create VBOOT_FLAG_DISPLAY_REQUESTED and set in vboot_handoff BUG=b:124141368, b:124192753, chromium:948529 TEST=make clean && make test-abuild TEST=build and flash eve device; attempt loading dev/rec modes BRANCH=none Change-Id: Idf111a533c3953448b4b9084885a9a65a2432a8b Signed-off-by: Joel Kitching <kitching@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/32262 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Julius Werner <jwerner@chromium.org>
2019-04-29mediatek: Add function to raise the CPU frequencyTristan Shieh
Implement mt_pll_raise_ca53_freq() in MT8183 to raise the CPU frequency. Move the function declaration to common header. BUG=b:80501386 BRANCH=none Test=Boots correctly on Kukui Change-Id: Ide8d767486d68177fa2bfbcc5b559879eca1bcda Signed-off-by: Tristan Shieh <tristan.shieh@mediatek.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/32465 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Hung-Te Lin <hungte@chromium.org> Reviewed-by: Julius Werner <jwerner@chromium.org>
2019-04-29mediatek/mt8183: Set CPU frequency to 1417MHzTristan Shieh
With the default CPU voltage (0.8v), CPU frequency should be 1417Mhz at most. We have to raise CPU frequency to 1989MHz after increasing CPU voltage to 1.05v in romstage. BUG=b:80501386 BRANCH=none Test=Boots correctly on Kukui Change-Id: I4c3e0fa27ccda8e0efe422b6ab503a1efb1697e9 Signed-off-by: Tristan Shieh <tristan.shieh@mediatek.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/32464 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Hung-Te Lin <hungte@chromium.org> Reviewed-by: Julius Werner <jwerner@chromium.org>
2019-04-29mediatek/mt8183: Init audio related clockJiaxin Yu
Enable audio clock, intbus clock, infra clock and mtkaif 26m clock.Needed by audio playback in firmware. BUG=b:117254418 BRANCH=none TEST=Build pass and verified on kukui p1 board Change-Id: I88060d9796cc23ad7f524943f36869e1ec85073d Signed-off-by: Jiaxin Yu <jiaxin.yu@mediatek.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/32458 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Hung-Te Lin <hungte@chromium.org>
2019-04-24mediatek/mt8183: Set CPU frequency to 1989MHzTristan Shieh
Set CPU frequency from 1100MHz to 1989MHz to improve booting time. BUG=b:80501386 BRANCH=none Test=Boots correctly on Kukui Change-Id: Id41c7ea8905c4db2537a5c32f96eb7c6b2c008ea Signed-off-by: Tristan Shieh <tristan.shieh@mediatek.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/32397 Reviewed-by: Hung-Te Lin <hungte@chromium.org> Reviewed-by: You-Cheng Syu <youcheng@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2019-04-24mediatek/mt8183: Set processor voltage to 1.05vTristan Shieh
The maximum CPU frequency is 1417MHz with current processor voltage (0.8v). Set processor voltage to 1.05v for higher CPU frequency. BUG=b:80501386 BRANCH=none Test=Boots correctly on Kukui Change-Id: I24ecdac2c85d3f012d9235449c0d727d727dc185 Signed-off-by: Tristan Shieh <tristan.shieh@mediatek.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/32396 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: You-Cheng Syu <youcheng@google.com> Reviewed-by: Hung-Te Lin <hungte@chromium.org>
2019-04-23src: include <assert.h> when appropriateElyes HAOUAS
Change-Id: Ib843eb7144b7dc2932931b9e8f3f1d816bcc1e1a Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/c/coreboot/+/26796 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org> Reviewed-by: David Guckian
2019-04-23src: Use include <console/console.h> when appropriateElyes HAOUAS
Change-Id: Iddba5b03fc554a6edc4b26458d834e47958a6b08 Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/c/coreboot/+/32214 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Werner Zeh <werner.zeh@siemens.com> Reviewed-by: David Guckian
2019-04-23src: Add missing include 'console.h'Elyes HAOUAS
Change-Id: Ie21c390ab04adb5b05d5f9760d227d2a175ccb56 Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/c/coreboot/+/32122 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
2019-04-17mediatek: Use the 64-bit timerTristan Shieh
GPT4 is a 32-bit timer and the counter of GPT4 will overflow in about 330 seconds (0xffffffff / 13MHz). Timer and delay functions will not work properly if the counter overflows. To fix that we should use the 64-bit timer (GPT6). BUG=b:80501386 BRANCH=none Test=emerge-elm coreboot; emerge-kukui coreboot Change-Id: I9f080e47253a1b1bab4636a45cb86c8666a25302 Signed-off-by: Tristan Shieh <tristan.shieh@mediatek.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/32245 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Hung-Te Lin <hungte@chromium.org> Reviewed-by: Julius Werner <jwerner@chromium.org> Reviewed-by: You-Cheng Syu <youcheng@google.com>
2019-04-06src: Use include <delay.h> when appropriateElyes HAOUAS
Change-Id: I23bc0191ca8fcd88364e5c08be7c90195019e399 Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/c/coreboot/+/32012 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Werner Zeh <werner.zeh@siemens.com> Reviewed-by: David Guckian
2019-04-06src: Use #include <timer.h> when appropriateElyes HAOUAS
Also, extra-lines added or removed and local includes moved down. Change-Id: I5e739233f3742fd68d537f671642bb04886e3009 Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/c/coreboot/+/32009 Reviewed-by: Nico Huber <nico.h@gmx.de> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2019-04-02mediatek/mt8183: Fix RTC initialization flowRan Bi
1. Fix RTC lpd settings. Rewrite powerkeys after lpd init to enable low power detect function. 2. Rearrange RTC initialization flow. 3. Add return status for rtc_init. 4. Add log if calling pwrap_write or pwrap_read fail. 5. Increase timeout time to resolve unexpected timeout. BUG=b:127405695 BRANCH=none TEST=Boots correctly on Kukui Change-Id: I6f26edd6699c2f6d9af80c285b70742b44407136 Signed-off-by: Ran Bi <ran.bi@mediatek.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/31968 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Daisuke Nojiri <dnojiri@chromium.org>
2019-03-20src: Use 'include <string.h>' when appropriateElyes HAOUAS
Drop 'include <string.h>' when it is not used and add it when it is missing. Also extra lines removed, or added just before local includes. Change-Id: Iccac4dbaa2dd4144fc347af36ecfc9747da3de20 Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/c/coreboot/+/31966 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Werner Zeh <werner.zeh@siemens.com> Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
2019-03-16src: Drop unused '#include <halt.h>'Elyes HAOUAS
Change-Id: Ie7afe77053a21bcf6a1bf314570f897d1791a620 Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/c/coreboot/+/31921 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-by: Arthur Heymans <arthur@aheymans.xyz> Reviewed-by: Angel Pons <th3fanbus@gmail.com>
2019-03-08coreboot: Replace all IS_ENABLED(CONFIG_XXX) with CONFIG(XXX)Julius Werner
This patch is a raw application of find src/ -type f | xargs sed -i -e 's/IS_ENABLED\s*(CONFIG_/CONFIG(/g' Change-Id: I6262d6d5c23cabe23c242b4f38d446b74fe16b88 Signed-off-by: Julius Werner <jwerner@chromium.org> Reviewed-on: https://review.coreboot.org/c/coreboot/+/31774 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Patrick Georgi <pgeorgi@google.com>
2019-03-07security/tpm: Fix TCPA log featurePhilipp Deppenwiese
Until now the TCPA log wasn't working correctly. * Refactor TCPA log code. * Add TCPA log dump fucntion. * Make TCPA log available in bootblock. * Fix TCPA log formatting. * Add x86 and Cavium memory for early log. Change-Id: Ic93133531b84318f48940d34bded48cbae739c44 Signed-off-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/29563 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Patrick Rudolph <siro@das-labor.org>
2019-03-04device/mmio.h: Add include file for MMIO opsKyösti Mälkki
MMIO operations are arch-agnostic so the include path should not be arch/. Change-Id: I0fd70f5aeca02e98e96b980c3aca0819f5c44b98 Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: https://review.coreboot.org/c/31691 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2019-03-04arch/io.h: Drop unnecessary includeKyösti Mälkki
Change-Id: I91158452680586ac676ea11c8589062880a31f91 Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: https://review.coreboot.org/c/31692 Reviewed-by: Patrick Georgi <pgeorgi@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2019-02-28mediatek/mt8183: Add RTC supportRan Bi
This patch implements RTC initialization. 1. initialization dcxo 2. rtc clock using dcxo 32k 3. export RTC_32K1V8_0 to SOC, export RTC_32K1V8_1 to WLAN 4. rtc register initialization 5. refactor the driver common part BUG=b:80501386 BRANCH=none TEST=Boots correctly on Kukui Change-Id: Icccb9360a507fcbfd865b107cd3630e71c810d55 Signed-off-by: Ran Bi <ran.bi@mediatek.com> Reviewed-on: https://review.coreboot.org/c/31046 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Julius Werner <jwerner@chromium.org>
2019-02-26mediatek/mt8183: Modify I2C source clockQii Wang
This patch change i2c source clock to TOPCKGEN. BUG=b:80501386 BRANCH=none TEST=Boot correctly on kukui. Change-Id: I49e0acda22dba449d0873a95ba5fae79a9cef569 Signed-off-by: Qii Wang <qii.wang@mediatek.com> Reviewed-on: https://review.coreboot.org/c/31519 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Hung-Te Lin <hungte@chromium.org>
2019-02-25security/vboot: Add measured boot modePhilipp Deppenwiese
* Introduce a measured boot mode into vboot. * Add hook for stage measurements in prog_loader and cbfs. * Implement and hook-up CRTM in vboot and check for suspend. Change-Id: I339a2f1051e44f36aba9f99828f130592a09355e Signed-off-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com> Signed-off-by: Werner Zeh <werner.zeh@siemens.com> Reviewed-on: https://review.coreboot.org/c/29547 Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2019-02-22symbols.h: Add macro to define memlayout region symbolsJulius Werner
When <symbols.h> was first introduced, it only declared a handful of regions and we didn't expect that too many architectures and platforms would need to add their own later. However, our amount of platforms has greatly expanded since, and with them the need for more special memory regions. The amount of code duplication is starting to get unsightly, and platforms keep defining their own <soc/symbols.h> files that need this as well. This patch adds another macro to cut down the definition boilerplate. Unfortunately, macros cannot define other macros when they're called, so referring to region sizes as _name_size doesn't work anymore. This patch replaces the scheme with REGION_SIZE(name). Not touching the regions in the x86-specific <arch/symbols.h> yet since they don't follow the standard _region/_eregion naming scheme. They can be converted later if desired. Change-Id: I44727d77d1de75882c72a94f29bd7e2c27741dd8 Signed-off-by: Julius Werner <jwerner@chromium.org> Reviewed-on: https://review.coreboot.org/c/31539 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2019-02-21mediatek/mt8183: Support gpio eh and rsel setting for I2Cjg_poxu
The setting of these registers are only for i2c pin. BUG=b:80501386 BRANCH=none TEST=Boot correctly on Kukui Change-Id: I518ca07645fe55aa55e94e4f98178baa0b74a882 Signed-off-by: jg_poxu <jg_poxu@mediatek.com> Reviewed-on: https://review.coreboot.org/c/30974 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Julius Werner <jwerner@chromium.org>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-26 11:35:39 +0000