| Age | Commit message (Collapse) | Author |
|---|
|
Kernel pinctrl driver changed for Tiger Lake and went to old scheme.
Kernel patch: https://chromium-review.googlesource.com/c/chromiumos/
third_party/kernel/+/2116670
BUG=b:151683980
BRANCH=none
TEST=Build and boot tgl board. In /sys/kernel/debug/pinctrl
verify INTC34C5:00 listing all the pins.
Cq-Depend:chromium:2116670
Change-Id: I9f1d399ff7380125ad5b935f9590a7d9cc442b04
Signed-off-by: Shaunak Saha <shaunak.saha@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39801
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
In addition to GBLRST_CAUSE0 and GBLRST_CAUSE1, print the value
of HPR_CAUSE0.
Change-Id: Idc57c3cd6a8d156c5544640898e8e7147d34c535
Signed-off-by: derek.huang <derek.huang@intel.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40648
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Updating EMMC PCR PID from 0x52 to 0x51 for Jasperlake
BUG=b:155595624
BRANCH=None
TEST=Build, boot JSLRVP from emmc
Signed-off-by: Ronak Kanabar <ronak.kanabar@intel.com>
Change-Id: I17d4e7b7e0fe5e0b18867b6481b5bc9227ae19e3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41028
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: V Sowmya <v.sowmya@intel.com>
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
|
|
SdCardPowerEnableActiveHigh is a UPD which controls polarity of SD card
power enable pin. Setting it 1 will set polarity of this pin as Active
high. This patch will allow to control it from devicetree so that it
can be set as per each board's requirement.
BUG=b:155595624
BRANCH=None
TEST=Build, boot JSLRVP, Verified UPD value from FSP log
Signed-off-by: Ronak Kanabar <ronak.kanabar@intel.com>
Change-Id: Id777a262651689952a217875e6606f67855fc2f4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41027
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: V Sowmya <v.sowmya@intel.com>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
PMC supports messages that can be used for configuring the USB
Type-C Multiplexer/Demultiplexer.
BUG=b:151646486
TEST=Booted to kernel on volteer board and verified PMC and Mux
agent devices identification.
Change-Id: I00c5f929b2eea5de3f8eba794dbe9b36c8083c52
Signed-off-by: John Zhao <john.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38777
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Update interrupt setting based on latest FSP(3163.01)
Reference:
https://github.com/otcshare/CCG-TGL-Generic-SiC/blob/TGL.3163.01/
ClientOneSiliconPkg/IpBlock/Itss/LibraryPrivate/PeiItssPolicyLib/
PeiItssPolicyLibVer2.c
BUG=b:155315876
BRANCH=none
TEST=Build with new FSP(3163.01) and boot OS and login OS console
in ripto/volteer. Without this change, we can't login due to mismatch
interrupt setting between asl and fsp setting.
Cq-Depend: chrome-internal:2944102
Cq-Depend: chrome-internal:2939733
Cq-Depend: chrome-internal:2943140
Signed-off-by: Wonkyu Kim <wonkyu.kim@intel.com>
Change-Id: Ibf70974b8c4f63184d576be3edd290960b023b1e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40872
Reviewed-by: Dossym Nurmukhanov <dossym@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Due to refactoring of Serial IO code in FSP v3163 onwards we need to
set SerialIoUartDebugMode UPD in FSP-M to SkipInit so that SerialIoUart
initialization is skipped in FSP. This makes sure that SerialIo
initialization in coreboot is not changed by FSP.
BUG=b:155315876
BRANCH=none
TEST=build and boot tglrvp/ripto/volteer and check UART debug logs
Cq-Depend: chrome-internal:2944102
Cq-Depend: chrome-internal:2939733
Cq-Depend: chrome-internal:2943140
Signed-off-by: Srinidhi N Kaushik <srinidhi.n.kaushik@intel.com>
Change-Id: I8ba4b9015fa25a84b6b99419ce4d413c9d9daa44
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40899
Reviewed-by: Dossym Nurmukhanov <dossym@google.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
For unknown reasons FSP skips a whole bunch of SIR (SATA Initialization
Registers) when SataPwrOptEnable=0, which currently is the default in
coreboot and FSP. Even if FSP's default was 1, coreboot would reset it.
This can lead to all sorts of problems and errors, for example:
- links get lost
- only 1.5 or 3 Gbps instead of 6 Gbps
- "unaligned write" errors in Linux
- ...
At least on two boards (supermicro/x11-lga1151-series/x11ssm-f and
purism/librem13v2) SATA is not working correctly and showing such
symptoms.
To let FSP correctly initialize the SATA controller, enable the option
SataPwrOptEnable statically. There is no valid reason to disable it,
which might break SATA, anyway.
Currently, there are no reported issues on CML and CNL, so a change
there could not be tested reliably. SKL/KBL was tested successfully
without any noticable downsides. Thus, only SKL gets changed for now.
Change-Id: I8531ba9743453a3118b389565517eb769b5e7929
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40877
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add DisableHeciRetry to the chip config and parse it in romstage.
Change-Id: I460b51834c7de42e68fe3d54c66acd1022a3bdaf
Signed-off-by: Christian Walter <christian.walter@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40756
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
|
|
In CSE Firmware Custom SKU, CSE region is logically divided into
2 boot partitions. These boot partitions are represented by BP1(RO),
BP2(RW). With CSE Firmware Custom SKU, CSE can boot from either
RO(BP1) or RW(BP2).
The CSE Firmware Custom SKU layout appears as below:
------------- -------------------- ---------------------
|CSE REGION | => | RO | RW | DATA | => | BP1 | BP2 | DATA |
------------- -------------------- ---------------------
In order to support CSE FW update to RW region, below APIs help coreboot
to get info about the boot partitions, and allows coreboot to set CSE
to boot from required boot partition (either RO(BP1) or RW(BP2)).
GET_BOOT_PARTITION_INFO - Provides info on available partitions in the CSE
region. The API provides info on boot partitions like start/end offsets
of a partition within CSE region, and their version and partition status.
SET_BOOT_PARTITION_INFO - Sets CSE's next boot partition to boot from.
With the HECI API, firmware can notify CSE to boot from RO(BP1) or RW(BP2)
on next boot.
As system having CSE Firmware Custom SKU, boots from RO(BP1) after G3,
so coreboot sets CSE to boot from RW(BP2) in normal mode and further,
coreboot ensure CSE to boot from whichever is selected boot partition
if system is in recovery mode.
BUG=b:145809764
TEST=Verified on hatch
Change-Id: Iaa62409c0616d5913d21374a8a6804f82258eb4f
Signed-off-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35402
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This change moves all ACPI table support in coreboot currently living
under arch/x86 into common code to make it architecture
independent. ACPI table generation is not really tied to any
architecture and hence it makes sense to move this to its own
directory.
In order to make it easier to review, this change is being split into
multiple CLs. This is change 3/5 which basically is generated by
running the following command:
$ git grep -iIl "arch/acpi" | xargs sed -i 's/arch\/acpi/acpi\/acpi/g'
BUG=b:155428745
Change-Id: I16b1c45d954d6440fb9db1d3710063a47b582eae
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40938
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
|
|
Perform the P2SB hide/unhide trick. This is needed so that BAR0
(0xfd000000) is not reclaimed by resource allocator, since it can
not deal with a device that does not exist (hidden).
Signed-off-by: Andrey Petrov <anpetrov@fb.com>
Change-Id: I5db0ae4e31d72ba86efba5728b2afc68d3180d5d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40921
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Maxim Polyakov <max.senia.poliak@gmail.com>
|
|
Use common P2SB driver. This is needed to address a problem when
enumerator does not see p2sb device (since it is hidden) but it
is active and BAR is decoded.
Change-Id: I9cb821a5684f15f1e1486872bf806a6ee3d0676f
Signed-off-by: Andrey Petrov <anpetrov@fb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40920
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add p2sb.h that is shared by all currently supported Xeon SP CPUs.
Change-Id: Idcbff7ad587cb116897a953c079fb0a8b86cc2ed
Signed-off-by: Andrey Petrov <anpetrov@fb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40919
Reviewed-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I8599dca99c1f34e3937c5b77b3505815ce625b46
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39453
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Change-Id: I9b15b5458bb8140fa9bb6b0ffb6b9c78e8d8a93b
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40848
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Change-Id: I353daf35c843521b089ff8411a9ba8c801605ff9
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40846
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Change-Id: Ie213b8c08e2d2b33a1dc1fda632163160d1cd70e
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40849
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Change-Id: If7e2c84c39039e0dc6811f247390f856fc634b33
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40844
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Change-Id: I09cc69a20dc67c0f48b35bfd2afeaba9e2ee5064
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40843
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Change-Id: I0fd1a758d8838b3eea5640b41eee6a6893360aa3
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40850
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
understanding
BIT 1 -> DEBUG_INTERFACE_UART_8250IO
BIT 4 -> DEBUG_INTERFACE_LPSS_SERIAL_IO
Change-Id: I566b9dc82b2289af42e58705ebeee51179886f1f
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40904
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
|
|
BUG=b:152019429
BRANCH=None
TEST=1. provision dram_part_num field of CBI
2. modify mainboard - dedede to report DRAM part number from CBI
3. check DRAM part number is correct in SMBIOS for memory device
Change-Id: I509d06a81bd005c5afe6e74a2da2ca408dee7b29
Signed-off-by: Marco Chen <marcochen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40833
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Fix FSP CAR on platforms that have ROM_SIZE of 32MiB.
CodeRegionSize must be smaller than or equal to 16MiB
to not overlap with LAPIC or the CAR area at 0xfef00000.
Tested on Intel CFL, the new code allows to boot using FSP-T.
Change-Id: I4dfee230c3cc883fad0cb92977c8f5570e1a927c
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39491
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Andrey Petrov <andrey.petrov@gmail.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
This CL adds support to fill PcieRpClkReqDetect UPD from devicetree.
Filling this UPD will allow FSP to enable proper clksrc gpio
configuration.
BUG=None
BRANCH=None
TEST=Build and boot tglrvp.
Change-Id: Iad0ba94fea019623a5b98fff0cb4a2cd1d2a7bd7
Signed-off-by: Meera Ravindranath <meera.ravindranath@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40832
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
|
|
This CL adds support to fill PcieRpClkReqDetect UPD from devicetree.
Filling this UPD will allow FSP to enable proper clksrc gpio
configuration.
BUG=None
BRANCH=None
TEST=Build and boot jslrvp with NVMe
Change-Id: Iad0b394fea019223a5b98fff0cb4a2bd1d2a7bd7
Signed-off-by: Meera Ravindranath <meera.ravindranath@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40757
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: V Sowmya <v.sowmya@intel.com>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-by: Ronak Kanabar <ronak.kanabar@intel.com>
|
|
Change-Id: I12345a5b6c9ce94ca9f8b555154b2278a8ff97bf
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39816
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Change-Id: I2bf1eb87bb5476dd77b5a56dfe8846e82d414523
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40666
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add support to generate ACPI operations to get/set/clear RX/TX GPIOs.
BUG=b:152936541
TEST=Build and boot the mainboard. Ensure that there are no errors in
the coreboot logs regarding unsupported ACPI GPIO operations.
Change-Id: Ibc4846fbd9baf4f22c48c82acefed960669ed7d4
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40536
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Check SPD is not NULL before print. This can prevent the system
from hanging up.
BUG=b:154445630
TEST=Check NULL SPD is not print.
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: Iccd9fce99eda7ae2b8fb1b4f3c2e635c2a428f04
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40560
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch adds GPID, a helper method to look up GPIO community ID for
an index.
This patch also includes Intel's common GPIO ASL code. CGPM method in
the common code uses the GPID method introduced in this patch.
BUG=b:148892882
BRANCH=none
TEST="BUILD volteer and ripto"
Signed-off-by: Venkata Krishna Nimmagadda <venkata.krishna.nimmagadda@intel.com>
Change-Id: Id6a00fb8adef0285d6bbc35cd5a44539bd3be6b8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40478
Reviewed-by: Venkata Krishna Nimmagadda <Venkata.krishna.nimmagadda@intel.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch adds CGPM, a helper method to configure GPIO power management
bits that are part of miscellaneous config. This is needed for
configuration of these bits on S0ix entry and exit.
BUG=b:148892882
BRANCH=none
TEST="BUILD volteer and ripto"
Signed-off-by: Venkata Krishna Nimmagadda <venkata.krishna.nimmagadda@intel.com>
Change-Id: Iac3a269d3071eb5d4100d516249eeb5ce23c02fa
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40260
Reviewed-by: Venkata Krishna Nimmagadda <Venkata.krishna.nimmagadda@intel.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Pointer passed to print_spd_info() from meminit.c needs to be
dereferenced first, so this change dereferences it.
BUG=b:154352883
TEST="emerge-volteer coreboot chromeos-bootimage", flash and boot
volteer, login to kernel and execute the following cbmem command:
localhost ~ # cbmem -c | grep LPDDR4X
and verify it returns "SPD: module type is LPDDR4X"
Change-Id: I5ff64121f0d50947c4946e9e02460dfb7319d01a
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40496
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
.acpi_inject_dsdt() does not need to modify the device
structure. Hence, this change makes the struct device * parameter to
acpi_inject_dsdt as const.
Change-Id: I3b096d9a5a9d649193e32ea686d5de9f78124997
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40711
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
.acpi_fill_ssdt() does not need to modify the device structure. This
change makes the struct device * parameter to acpi_fill_ssdt() as
const.
Change-Id: I110f4c67c3b6671c9ac0a82e02609902a8ee5d5c
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40710
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
intel_igd_get_controller_info() does not need to modify the device
structure. Hence, this change makes the struct device * parameter to
intel_igd_get_controller_info() as const.
Change-Id: Ic044a80e3e2c45af6824a23f3cd0b08b94c0f279
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40709
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
sd_fill_soc_gpio_info() does not need to modify device
structure. Hence, this change makes the struct device * parameter to
this function as const.
Change-Id: I237ee9640ec64061aa9ed7c65ea21740c40b6ae2
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40708
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
dw_i2c_soc_dev_to_bus() does not need to modify the device
structure. Thus, this change makes the struct device * parameter to
dw_i2c_soc_dev_to_bus as const.
Change-Id: Ibf5c8d8127dff2ab2ccbd1f6b4f553e98e81955f
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40704
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
.write_acpi_tables() should not be updating the device structure. This
change makes the struct device * argument to it as const.
Change-Id: I50d013e83a404e0a0e3837ca16fa75c7eaa0e14a
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40701
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Set SPD array NULL if no DIMM present. do_smbus_read_byte returns
negative value if SMBus transaction fails.
BUG=b:154445630,b:151702387
TEST=Check SPD is NULL if no DIMM in the slot.
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: Ie81adbfab5bb1d5c557fe549a158cb68e26b1162
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40558
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
According to doc 621880, it suggests setting 40 ohm in byte 185 in extCSD.
This commit provides _DSM method for driver to query driving strength.
TEST=mmc extcsd read |grep HS_TIMING and found bit[7:4] is set to 4
BUG=b:154159888
Signed-off-by: Kane Chen <kane.chen@intel.com>
Change-Id: I1b4df8b0d1d2cad3a7f521ad47ee5a4b3320c767
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40467
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
On Comet Lake, add the following microcode updates from the 3rdparty
repository:
- 06-8e-0c (CPUID signature: 0x806ec)
- 06-a6-00 (CPUID signature: 0xa0660)
Tested with Clevo N141CU.
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Change-Id: Id10b013df8ce98a4e9830782570e20fbcfad05c1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40580
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Add new MCH device-ids for jasperlake.
Reference is taken from jasperlake EDS volume 1 chapter 13.3.
BUG=None
BRANCH=None
TEST=code compiles and able to boot the platform.
Change-Id: I38e09579c9a3681e9168c66085cbb3a092dc30cc
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40589
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: V Sowmya <v.sowmya@intel.com>
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
|
|
Populate SMBIOS type 17 tables using data from SPD and read via IOSF.
Refactor print_dram_info() to pass thru SPD data and channel/speed info.
Move call to print_dram_info() after cbmem initialization so the SMBIOS
data has somewhere to go.
Test: build/boot google/swanky, verify via dmidecode.
Change-Id: I1c12b539c78d095713421b93115a4095f3d4278d
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40643
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
This patch removes APL SoC selecting CONFIG_PCIEX_LENGTH_256MB Kconfig
as default configuration for CONFIG_SA_PCIEX_LENGTH_MIB is 256MB.
TEST=Able to build and boot APL platform.
Change-Id: I61249f0adff5e03c07a568556e1ff76b27c6d368
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40378
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Pratikkumar V Prajapati <pratikkumar.v.prajapati@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
For DDR4, FSP expects channel 0 to set SPD for index 0 and channel 1
to set SPD for index 4. This change adds a helper macro to translate
DDR4 channel # to the index # that the FSP expects.
BUG=b:154445630
TEST=Verified that memory initialization for DDR4 is successful.
Change-Id: I2b6ea2433453a574970c1c33ff629fd54ff5d508
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40588
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kane Chen <kane.chen@intel.com>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
|
|
Assuming given system is populated with multiple CPUs of same SKUs,
calculate number of threads based on MAX_SOCKET.
This is a stop gap solution until proper way of identifying total
number of sockets is determined.
Change-Id: I7ebad3d57c47b9eeb7d727ffb21bc0a1a84734fd
Signed-off-by: Andrey Petrov <anpetrov@fb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40671
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Maxim Polyakov <max.senia.poliak@gmail.com>
|
|
Some dual-socket socket systems offer over 100 threads available.
Other multi-socket configurations potentially offer even greater
numbers of CPUs (over 9000!).
Bump MAX_CPUS to 255.
Change-Id: I50a181b89f40777a9f7b3881280c7bacf1b947cb
Signed-off-by: Andrey Petrov <anpetrov@fb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40556
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Currently FSP-M does not implement the spec completely, e.g it is unable
to use user-provided heap location in CAR. While this is being resolved,
this workaround is a stop-gap solution that allows multi-socket usage.
TEST=tested on OCP Sonora Pass EVT and Intel Cedar Island CRB
Change-Id: Ia2529526a8724cf54377b0bd2339b04fa900815a
Signed-off-by: Andrey Petrov <anpetrov@fb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40555
Reviewed-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
We need to allow motherboards to configure certain parameters that
are specific to it. Hence, invoke this function. Also, provide a
weak motherboard implementation that does nothing.
Change-Id: Ifa2824811273236a66e742404856fbe17d4cf496
Signed-off-by: Andrey Petrov <anpetrov@fb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40552
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add acpigen methods which generate operations to get/set/clear RX/TX GPIOs.
Verify it matches https://doc.coreboot.org/acpi/gpio.html.
BUG=b:149588766
TEST=confirmed with touchscreen gpios.
Signed-off-by: Alex Levin <levinale@chromium.org>
Change-Id: Id9fe26f14a606ceedb9db02d76fe8d466d3a21af
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40550
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Jes Klinke <jbk@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add Type-C subsystem power management support for RTD3.
BUG=b:140290596
TEST=Include "tcss.asl" in platform "dsdt.asl" for coreboot build
with the firmware CM. Added acpi debug and booted to kernel. Probed
devices PM_STATE transition from D0 to D3 entry/exit while system at S0.
TBT PCIe root ports: 00:07.0/00:07.1/00:07.2/00:07.3, offset:0xA4, PM_STATE:D3HT.
xhci:00:0d.0, offset:0x74, PM_STATE:D0D3.
dma:00:0d.2/00.0d.3, offset:0x84, PM_STATE:PMST.
Verified xhci/dma/pcie root ports power runtime_status to be suspended and suspended
time tick through /sys/bus/pci/devices/bus:device:func/power.
Change-Id: I127d3700ad426a44639ee93b4477be6638b42e1b
Signed-off-by: John Zhao <john.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39785
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Remove explicit setting of iDisp Link parameters. These settings are
related to configuration for the link between HD-Audio controller and
Display unit for purposes of HDMI/DP Audio playback. During PO,
observed that without setting these params display part was not
binding. With the latest code verified that we dont need to explicitly
set these parameters anymore. HDMI/DP audio playback works fine with
default settings.
BUG=b:151451125
BRANCH:none
TEST= build and boot volteer/ripto and verify HDMI/DP audio playback
Signed-off-by: Srinidhi N Kaushik <srinidhi.n.kaushik@intel.com>
Change-Id: Ie003d119918d363e2ff9172936b70416fd73c7f4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40263
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Jairaj Arava <jairaj.arava@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch adds _DSM Method in LPIT table for entering and exiting
S0ix. This method get injected into DSDT table and called from kernel.
LPIT table is hardcoded in this patch but the proper way to implement
is to use inject_dsdt to make the _DSM methods available for soc's to
implement.
Calling the LPIT table from mainboard here so that with the current
implementation the platforms which do not have lpit support throw
compilation error.
BUG=b:148892882
BRANCH=none
TEST="BUILD"
Signed-off-by: Venkata Krishna Nimmagadda <venkata.krishna.nimmagadda@intel.com>
Change-Id: Ib58f2e33a33bac9cc5f6aca28e85a8066413a5cf
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40259
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Venkata Krishna Nimmagadda <Venkata.krishna.nimmagadda@intel.com>
|
|
Merge the recent change from other platform(ICL/JSL).
- Update SKpMpInit setting
- Update APIs for getting dev info
- Update IGD related setting
- Update debug interface setting
BRANCH=none
TEST=build and boot ripto/volteer
Signed-off-by: Wonkyu Kim <wonkyu.kim@intel.com>
Change-Id: Ie4dd4bcef3d8afc71ae4a542dbe8e4ba385593cd
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40349
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Reviewed-by: Srinidhi N Kaushik <srinidhi.n.kaushik@intel.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: Idea18f437c31ebe83dd61a185e614106a1f8f976
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38199
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
The error message has been copy-pasted across various functions, so it
is nearly impossible to know which function printed it. So, use __func__
to print that information.
Change-Id: I55438c2b36cc3b21f3f168bf98b0aca5fd50bbbc
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40446
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Tigerlake platform does not have built in eMMC/SD support so all
this code is unused and can be removed.
Change-Id: I70ff983d175375171d5a649378f32f1062c0876d
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40372
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The eMMC/SD interface is not present in all Intel platforms so this
change removes the default enable for the storage controller and
instead enables it in the specific SoCs that do provide it.
Currently this includes all platforms except Tigerlake.
Change-Id: I8b6cab41dbd5080f4a7801f01279f47e80ceaefd
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40371
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Adds a new macro that allow to set the DRIVER or ACPI as host software
ownership for the GPI pad using the parameter own. Thus, this macro can
define more variants for pad configuration than others.
This is necessary to describe in more detail the configuration for the
Tioga Pass OCP server [1] and other boards. In addition, these changes
will be used to automatically generate macros [2] and great simplify
this task.
[1] https://review.coreboot.org/c/coreboot/+/39427
[2] https://review.coreboot.org/c/coreboot/+/35643
Change-Id: I9c191fb6935e94da6e296f8fee0b91a973534e1a
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40276
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Add C621A, C627A and C629A SKU IDs. C621A is used in the Whitley Product.
We need to add device ID for setting LPC resources.
Refer to Intel C620 series PCH EDS (547817).
Change-Id: I19a4024808d5aa72a9e7bd434613b5e7c9284db8
Signed-off-by: BryantOu <Bryant.Ou.Q@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40395
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
"Aplollolake" => "Apollolake"
Change-Id: I1881d40b5f71d07d5d217b4380241cc14467fb1a
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40407
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
TCSS TBT PCIE root ports scope type was mistakenly set to PCI_ENDPOINT.
Fix the scope type to be PCI_SUB.
BUG=b:141609884
TEST=Booted to kernel and verified no TBT PCIE root ports scope
type mismatch error in kernel log.
Change-Id: I844e7e9583992be496223fb51f24c5aa24fc7d21
Signed-off-by: John Zhao <john.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40004
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
BUG=b:151161585
BRANCH=none
TEST=build and boot ripto/volteer and check FSP logs for lockdown
parameters
Signed-off-by: Wonkyu Kim <wonkyu.kim@intel.com>
Change-Id: I63cec8a718285f424914e426d0399ed821588dfd
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39710
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Provide the option to disable XHCI LFPS power management.
If the option is set in the devicetree, the bits[7:4] in
XHCI MMIO BAR + offset 0x80A4 (PMCTRL_REG) will be updated
from default 9 to 0.
BUG=b:146768983
BRANCH=None
TEST=build coreboot with DisableXhciLfpsPM being set to 1 and flash
the image to the device. Run following command to check if
bits[7:4] is set 0:
>iotools mmio_read32 "XHCI MMIO BAR + 0x80A4"
Signed-off-by: Marx Wang <marx.wang@intel.com>
Change-Id: Ic603e3b919d8b443c6ede8bb5e46e2de07fcb856
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40255
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
In order to support mainboards that do not store DRAM part number in
the traditional way i.e. within the CBFS SPD for soldered memory, this
change provides a runtime callback to allow mainboards to provide DRAM
part number from a custom location e.g. external EEPROM on dedede.
For other boards it should be a NOP since the weak implementation of
mainboard_get_dram_part_num does nothing.
BUG=b:152019429
Change-Id: I7ba635f5504ba288308d7d7a4935f405f289aa8d
Signed-off-by: Marco Chen <marcochen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40302
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Add a function to dump ME Host Firmware Status registers.
BUG=None
BRANCH=None
TEST=Build and boot iclrvp.
Change-Id: I9430189665c94decb2e64680d28a7390ee6e912c
Signed-off-by: Krishna Prasad Bhat <krishna.p.bhat.d@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39128
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
|
|
Add a function to dump ME Host Firmware Status registers.
In tigerlake, Manufacturing mode is “No” if below conditions are satisfied, indicating
end of manufacturing. Otherwise, manufacturing mode is "Yes".
1. Intel fuses are programmed (Indicated by HFSTS6[30] bit set)
2. The SPI flash descriptor region is locked. (Indicated by HFSTS1[4] cleared)
BUG=None
BRANCH=None
TEST=Build and boot tglrvp.
Change-Id: I831a51f9f482425bd3b97ef1d2404b1d06844d07
Signed-off-by: Krishna Prasad Bhat <krishna.p.bhat.d@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39127
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
|
|
Make use of print_me_fw_version() which is defined in the CSE lib to
print ME firmware version information for icl,tgl.
BUG=None
BRANCH=None
TEST=Build and boot iclrvp, tglrvp boards.
Change-Id: Ief75403c490eee499a84372e54fa38ea3016cc11
Signed-off-by: Krishna Prasad Bhat <krishna.p.bhat.d@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39147
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Reviewed-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
|
|
Add LTR and AER configuration to the root ports config.
BUG=b:151166040
TEST= build and boot volteer and check LTR and AER value
from FSP log
Signed-off-by: Wonkyu Kim <wonkyu.kim@intel.com>
Change-Id: I668f2e5fea15019a9e5ae06fb4d55fa2aea69e8a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40262
Reviewed-by: Srinidhi N Kaushik <srinidhi.n.kaushik@intel.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Some of the revision 4 FADT fields were already updated to ACPI
spec revision 6, but not all of them. In addition the advertised
FADT revision was 3.
Implement all fields as defined in version 6 and bump the advertised
FADT revision to 6.
Also set all used access_size fields and x_gpe0_blk to sane values
as Windows 10 verifies those fields starting with FADT revision 5.
Fixes: https://ticket.coreboot.org/issues/109
Tested on Windows 10.
Change-Id: Ic649040025cd09ed3e490a521439ca4e681afbbf
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39805
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
|
|
Remove EMMC and SD card ACPI devices copied from Ice Lake.
Tiger Lake does not support these controllers.
BUG=b:151208782
TEST= Build volteer board
Change-Id: I4b3e37f93b94757d16d775fb27bee644d9dc539e
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40228
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change disables MrcSafeConfig option during MRC training.
MrcSafeConfig was enabled as part of the early testing.
Now with FSP 2527, there is no need to set this config anymore.
BUG=b:150357377
BRANCH=master
TEST=build and boot ripto/volteer
Signed-off-by: Srinidhi N Kaushik <srinidhi.n.kaushik@intel.com>
Change-Id: I4e4069d83754aaf1e4885d6912ab2a6d506c5269
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40106
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=b:150872580
TEST=Build waddledoo board. Verify EMMC and SD card ACPI devices are
present in dsdt.asl.
Change-Id: I70d47455c48990afe9e79c013c5272d70f4f71e7
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39582
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
|
|
Current pin-ctrl kernel v5.4 driver expects the firmware to publish
single GPIO ACPI device. Until kernel pin-ctrl driver implementation is
updated to consume community based GPIO ACPI device, update the current
ACPI code to comply with pin-ctrl driver requirement.
BUG=b:150154277
TEST=Verify intel pin-ctrl driver can successfully load in OS
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Change-Id: Ifcc92adaee550182ab405541ea85019f31bb8658
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39470
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
|
|
`.read_resources` and `.set_resources` are the only two device
operations that are considered mandatory. Other function pointers
can be left NULL. Having dedicated no-op implementations for the
two mandatory fields should stop the leaking of no-op pointers to
other fields.
Change-Id: I6469a7568dc24317c95e238749d878e798b0a362
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40207
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Providing an explicit no-op function pointer is only necessary for
`.read_resources` and `.set_resources`. All other device-operation
pointers are optional and can be NULL.
Change-Id: I3d139f7be86180558cabec04b8566873062e33be
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40206
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Support to configure DDR4 memory variant.
-Add support to read SPD data based on different memory topology.
-Initialize FSP UPD's for DQ and DQS mapping.
BUG=b:151702387
Signed-off-by: Varun Joshi <varun.joshi@intel.corp-partner.google.com>
Change-Id: I47a5dcad3ee316871a6103b9d53ef7f6fc88d7d8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39847
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Set IgdDvmt50PreAlloc to zero if InternalGfx is disabled. It's 'correct'
to do it like this, otherwise the FSP would always allocate memory for
the IGD even if it is disabled. In addition the FSP enables the graphics
panel power even if no IGD is present which leads to a crashing FSP.
Thus, if no IGD is present we switch off the panel via UPDs.
Refer to this issue on IntelFSP for details:
https://github.com/IntelFsp/FSP/issues/49
Tested on:
* CFL platform with IGD
* CFL platform without IGD
Change-Id: I6f9e0f9855224614471d8ed23bf2a9786386ddca
Signed-off-by: Christian Walter <christian.walter@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39454
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Change-Id: Ib156ebede1ee24a1c7bd20d01792ec80cba8f37d
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39991
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Allow the use of the common/gpio driver to create Lewisburg PCH pad
configurations for server motherboards with Skylake-SP processors.
This patch should only be applied after adding Lewisburg PCH definitions
to the soc/intel/xeon_sp code [1].
[1] https://review.coreboot.org/c/coreboot/+/39425
Change-Id: I4a8e83cad0729bbbb50ba5a2b336f6cf7c1eca13
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39428
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Allow to print a debug error message when the GPIO community does not
contain the pad number from the motherboard configuration.
Change-Id: I21fb389a5d29e11b1fbc24e836d91e17957047f1
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40021
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Andrey Petrov <andrey.petrov@gmail.com>
|
|
Adds definitions that allow to use the common GPIO driver to configure
the Lewisburg PCH pads. Using the GPIO configuration from common/gpio,
unlike the FSP-style definitions from Intel RefCode [1] definitions,
is more understandable and makes the motherboards code much cleaner.
In addition, we can use utilities, such as inteltool, to analyze the
configuration of proprietary firmware to add support for new server
motherboards with Skylake-SP processors.
The pin layout in this patch corresponds to the pinctrl driver in the
Linux kernel v4.14 for the Lewisburg PCH GPIO controller [2].
[1] https://designintools.intel.com/product_p/stlgrn45.htm
[2] drivers/pinctrl/intel/pinctrl-lewisburg.c
These changes are in accordance with the documentation:
[*] page 39, Intel(R) C620 Series Chipset Platform Controller Hub
(PCH) Datasheet, May 2019. Document Number: 336067-007US.
Change-Id: Idde32fdd53f1966e3ba6b7f5598ae8f51488d5a5
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39425
Reviewed-by: Andrey Petrov <andrey.petrov@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
HSA -> HDA (High Definition Audio)
Change-Id: Ic0e6ad7b26105fdd6eca6cd11edcf2236e5c7123
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40232
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
In order to support mainboards that do not store DRAM part number in
the traditional way i.e. within the CBFS SPD for soldered memory, this
change provides a runtime callback to allow mainboards to provide DRAM
part number from a custom location e.g. external EEPROM on volteer /
dedede.
For other boards it should be a NOP since the weak implementation of
mainboard_get_dram_part_num does nothing.
BUG=b:152019429
Change-Id: If940a76d36a7645a7441ba418aa7aec9af9f6319
Signed-off-by: Marco Chen <marcochen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39860
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Done with sed and God Lines. Only done for C-like code for now.
Change-Id: I482715c166ccf5d2f3cc25118d25b07dbfd6650a
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40219
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
|
|
Done with sed and God Lines. Only done for C-like code for now.
Change-Id: I3fdfa159194cccf15c0284700f554d2241dad6cd
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40217
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
|
|
Done with sed and God Lines. Only done for C-like code for now.
Change-Id: I2efdeb224c478995d393aa3eaac762c876832391
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40216
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
|
|
Done with sed and God Lines. Only done for C-like code for now.
Change-Id: I1edbc8bb0efaad033385f29f8a4747bd178296b9
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40215
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
|
|
Done with sed and God Lines. Only done for C-like code for now.
Change-Id: Ib1e226e7816efbc5cffc95563b440fb2ad5b1f95
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40214
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
|
|
Done with sed and God Lines. Only done for C-like code for now.
Change-Id: I48422453735d50eb9292f39a3c031073d647a17c
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40212
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
|
|
Done with sed and God Lines. Only done for C-like code for now.
Change-Id: I8995372760543e9cf2c845019f7a063046c55e9c
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40211
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
|
|
Done with sed and God Lines. Only done for C-like code for now.
Change-Id: Ib41169395ab239e520f6047ac6bd307ec50776d4
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40209
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
|
|
Done with sed and God Lines. Only done for C-like code for now.
Change-Id: Ic5a920bfe1059534566ceab85a97219dd56f069e
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40213
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Done with sed and God Lines. Only done for C-like code for now.
Change-Id: I45d746ed374361036d59167293a90d8e557754fa
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40210
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
|
|
Done with sed and God Lines. Only done for C-like code for now.
Change-Id: I7354edb15ca9cbe181739bc2a148f16bb85ab118
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40218
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
|
|
Done with sed and God Lines. Only done for C-like code for now.
Change-Id: I703a656c397345025dab398fb642f3de7bbb61fe
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40220
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Done with sed and God Lines. Only done for C-like code for now.
Change-Id: I3c6daa484a4aa133ff2ad79eb2b8efa159da3523
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40208
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
It is use to skip GT specific programming in ICL, TGL and JSL.
In following patches use of SKIP_GRAPHICS_ENABLING is removed.
b6a523927d (soc/intel/jasperlake: Remove DDI A lane programming)
e5565c45cb (soc/intel/{icelake, tigerlake}: Remove DDI A lane programming)
TEST=checked iclrvp, jslrvp and tglrvp compilation.
Change-Id: Ie337fd727d72118c43aa869da1446ea4fceadc5b
Signed-off-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40039
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
|
|
For newer Intel graphics (>=11), the DDI port max lanes default to 4.
And kernel driver no longer relies on coreboot to provide information
via DDI_BUF_CTL_A (for DDI port A) register programming. Hence removing
this code.
BUG=b:150788968
BRANCH=None
TEST=checked jslrvp compilation and boot.
Change-Id: I4c171ec6a57d6fc53bee88420bfb3c0fbc5dc057
Signed-off-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40038
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
