| Age | Commit message (Collapse) | Author |
|---|
|
This patch brings the feature of disabling RAPL to common code. It
replaces the current solution for APL and EHL.
For special case if RAPL disabling is only working via changes in MCHBAR
a new config switch was introduced.
Test: Boot mc_apl4/5 with this patch and ensure that the
relevant bits in MSR 0x610 are the same as before the
patch.
Change-Id: I2098ddcd2f19e3ebd87ef00c544e1427674f5e84
Signed-off-by: Uwe Poeche <uwe.poeche@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/64596
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
|
|
This patch adds support for the ADL-N SKUs based on the PCH ID.
Document reference: 645548 (ADL-N EDS Volume 1).
BUG=None
BRANCH=None
TEST=Build FW and test on adln_rvp board
Change-Id: I24c18a27a4a2c68c78bc3dc728c45ba04f57205d
Signed-off-by: Vidya Gopalakrishnan <vidya.gopalakrishnan@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/64472
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
|
|
This patch implements a SoC overrides to set CPU privilege level
as the MSR is not consistent across platforms. For example:
On APL/GLK/DNV, it's MSR 0x120 and CNL onwards it's MSR 0x151.
BUG=b:233199592
TEST=Build and boot google/taeko to ChromeOS.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I4584516102560e6bb2a4ae8c0d036be40ed96990
Reviewed-on: https://review.coreboot.org/c/coreboot/+/64806
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
|
|
mtrr_use_temp_range is a lot smarter than the plain set_var_mtrr. It
will compute a new optimal solution with the temp ranges included
while also taking care of the cleanup before loading the payload/s3
resume.
Change-Id: I283ba07fc12c410be39dfdc828657598237247c1
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63550
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The patch uses coreboot error codes instead of uint8_t data type in the
pre_mem_debug_init function.
TEST=build code for Gimble
Signed-off-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Change-Id: I957ff764900cb789bf2aacf0472dcb281f48af07
Reviewed-on: https://review.coreboot.org/c/coreboot/+/64301
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
|
|
Based on the constraints for CML.
Fixes the following warnings in Linux on system76/oryp8 and
system76/gaze16, which have an NVIDIA GPU on the bridge.
pcieport 0000:00:01.0: can't derive routing for PCI INT A
pcieport 0000:00:01.0: can't derive routing for PCI INT B
This, in turn, resolves an IRQ conflict with the PCH HDA device that
would cause a stack trace on every boot and on S3 suspend.
irq 10: nobody cared (try booting with the "irqpoll" option)
<snip>
[<00000000fb84c354>] azx_interrupt [snd_hda_codec]
Disabling IRQ #10
Change-Id: Ibc968aaa7bf0259879097ff69d2543dcfa2e5e4b
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/64671
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Select `HAVE_HYPERTHREADING` and hook up the hyper-threading setting
from the FSP to the option API so that related mainboards don't have to
do that. Unless otherwise configured (e.g. the CMOS setting or overriden
by the mainboard code), the value from the Kconfig setting
`FSP_HYPERTHREADING` is used.
Change-Id: I520a936b4c3a8997ba2c6bea0126b3bbcc5d68ce
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/60547
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sean Rhodes <sean@starlabs.systems>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Select `HAVE_HYPERTHREADING` and hook up the hyper-threading setting
from the FSP to the option API so that related mainboards don't have to
do that. Unless otherwise configured (e.g. the CMOS setting or overriden
by the mainboard code), the value from the Kconfig setting
`FSP_HYPERTHREADING` is used.
Also, remove related code from the mainboard starlabs/laptop/tgl, since
it is obsolete now.
Change-Id: I49bbd4a776b4e6c55cb373bbf88a3ca076342e3e
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/60545
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sean Rhodes <sean@starlabs.systems>
|
|
Select `HAVE_HYPERTHREADING` and hook up the hyper-threading setting
from the FSP to the option API so that related mainboards don't have to
do that. Unless otherwise configured (e.g. the CMOS setting or overriden
by the mainboard code), the value from the Kconfig setting
`FSP_HYPERTHREADING` is used.
Also, remove related code from the following mainboards, since it is
obsolete now.
* siemens/chili
* starlabs/laptop/cml
Change-Id: I173b87da5ce76549672c50ba30204cd77be8b82f
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/60544
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sean Rhodes <sean@starlabs.systems>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Move the Kconfig option `FSP_HYPERTHREADING` to common Intel Kconfig so
that it can be reused by other SoCs. Since not all SoCs support
hyperthreading, make it conditional on `HAVE_HYPERTHREADING`. SoCs
supporting hyperthreading need to select it so that `FSP_HYPERTHREADING`
is available.
Change-Id: I892d48b488cbf828057f0e9be9edc4352c58bbe7
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/60543
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sean Rhodes <sean@starlabs.systems>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
The patch skips sending DISCONNECT IPC command to PMC if system resumes
from S3.
coreboot notice DISCONNECT IPC command getting timedout during S3
resume if system has AC connected behind Type-C hub. This impacts
system resume time. Please refer TA# 730910 for more information.
coreboot need not send the DISCONNECT IPC command when system resumes
from S3 state.
TEST=Verified system boots to OS and verfied below tests on Gimble
1. coreboot doesn't send the DISCONNECT during S3 resume
2. After S3 resume, system detects the pen drive with Superspeed
3. After system resumes from S3, hot-plug the pen drive, system detects
the pen drive
3. System sends IPC commands when system boots from S0 or S5.
Signed-off-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Change-Id: I6ad006ae8677919c7dfeca8eec0af11454a2e89d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63932
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
The FSP includes a UPD to set the DPA (Dynamic Periodicity
Alteration) PreWake value, which can be used to set the maximum
pre-wake randomization time in "micro-ticks". This patch adds
support for configuring that value.
BUG=b:228410327
TEST=build FW and checked DPA value by fsp log.
Signed-off-by: leo.chou <leo.chou@lcfc.corp-partner.google.com>
Change-Id: I08897c590a88aba058cb9e364185ea0794e1e7c3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/64316
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
This patch drops the unused `PCH_DEV_SLOT_LPC` macro from the
Tiger Lake SoC PCI device list.
BUG=none
TEST=Able to build and boot volteer, google board.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I27a2f31aa706c4d76e9f0db202422bc129368959
Reviewed-on: https://review.coreboot.org/c/coreboot/+/64588
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
|
|
All targets now use cbmem for the BERT region, so the implementation can
be common.
This also drops the obsolete comment about the need to have bert in a
reserved region (cbmem gets fixed to be in a reserved region).
Change-Id: I6f33d9e05a02492a1c91fb7af94aadaa9acd2931
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/64602
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Since the FIT pointer is patched at runtime there is no guarantee that
the pre-defined one will match the patched one. Add a check and print a
warning at runtime if both addresses (pre-defined and patched) do not
match as in this case an offline computed hash for the bootblock will
differ from the runtime one.
Change-Id: Ib1b02ec43af183caa9f5b08b3c485879b423c40f
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/64598
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Before TXE releases the CPU out of reset a pointer to the constructed
FIT in SRAM is patched into the loaded bootblock at offset 4G - 64B.
Since this patched bootblock gets measured during runtime it will not
match the one that is potentially measured from the coreboot image.
This patch adds a dedicated fit.c file for Apollo Lake where the FIT
pointer is already set to the address TXE will be using at runtime.
Test=Compare sha256 sum from coreboot runtime and coreboot.rom of the
bootblock and make sure they match.
Change-Id: Ia0fd2a19517c70f50ef37e6a2dc2408bae28df10
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/64539
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
On Apollo Lake the bootblock is stitched into the IBBL IFWI region at
build time. At execution time TXE loads this IBBL into a shared SRAM
(which is read-only in this phase) and maps it at 4 GiB - 32 KiB. Then
the CPU starts to operate from this shared SRAM as it were flash space.
In order to provide a reliable CRTM init, the real executed bootblock
code needs to be measured into TPM if VBOOT is selected. This patch adds
the needed code to do this.
Change-Id: Ifb3f798de638a85029ebfe0d1b65770029297db3
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/64493
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
On platforms where the bootblock is not included in CBFS anymore
(because it is part of another firmware section (IFWI or a different
CBFS), the CRTM measurement fails.
This patch adds a new function to provide a way at SoC level to measure
the bootblock. Following patches will add functionality to retrieve the
bootblock from the SoC related location and measure it from there.
In this way the really executed code will be measured.
Change-Id: I6d0da1e95a9588eb5228f63151bb04bfccfcf04b
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/64492
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Add the boot flash MMIO window to the resources to report this region as
reserved to the OS. This is done to stay consistent with the reserved
memory ranges by coreboot and make the OS aware of them.
As x86 systems preserves the upper 16 MiB below 4G for BIOS flash
decoding use the complete window for reporting independent of the
actually used SPI flash size. This will block the preserved MMIO window.
Change-Id: Ib3a77e9233c3c63bad4de926670edb4545ceaddf
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/64077
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
This patch drops the unused `PCH_DEV_SLOT_LPC` macro from the
Alder Lake SoC PCI device list.
BUG=none
TEST=Able to build and boot taeko, google board.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: Ib2ae40fcc4499de34534f27f03b4c359c37409e6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/64586
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Since the fast SPI controller is hidden on Apollo Lake the OS cannot
probe it and is therefore unaware of the reserved resources assigned in
coreboot. Select 'FAST_SPI_GENERATE_SSDT' to enable SSDT creation to
report the reserved resources to the OS.
Change-Id: I23e77a0a01141dc4f299988d19509e6df555a654
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/64419
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Sean Rhodes <sean@starlabs.systems>
|
|
This patch provides the possibility for EHL based boards to disable
RAPL settings via SOC_INTEL_DISABLE_POWER_LIMITS config switch.
On Elkhart Lake the way via setting relevant MSR bits does not work.
Therefore the way via MCHBAR is choosen.
Test:
Check MCHBAR mapped registers (MCH_PKG_POWER_LIMIT) on mc_ehl1.
Change-Id: I5be6632b15ab8e14a21b5cd35152f82fec919d9f
Signed-off-by: Uwe Poeche <uwe.poeche@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63547
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
EHL MAC side expects a rising edge signal for an IRQ. Based on the
mainboard wiring it could be necessary to change the interrupt polarity.
This patch provides the functionality to invert a falling edge signal
that comes from an external PHY. The inverting can be activated via
devicetree parameter.
Change-Id: Ia314014c7cacbeb72629c773c8c0bb5f002a3f54
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63888
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: I37d31598e87e5b625ded3186980e3aba7dcf6440
Reviewed-on: https://review.coreboot.org/c/coreboot/+/64523
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Hook Timer8254ClkSetting to `legacy_8254_timer` cmos option. If that
isn't set, fallback to the `USE_LEGACY_8254_TIMER` Kconfig option.
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: I4f91cc2c8f48e9da47399059386092314b631b08
Reviewed-on: https://review.coreboot.org/c/coreboot/+/64522
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
|
|
If the SPI controller is hidden from the OS (which is default on Apollo
Lake) then OS has no chance to probe the device and therefore can not be
aware of the resources this PCI device occupies. If the OS needs to move
some resources for a reason it can happen that the new allocated window
will be shadowed by the hidden PCI device resource and hence causing a
conflict. As a result this MMIO window will be inaccessible from the OS
which will cause issues in applications. For instance on Apollo Lake
this causes flashrom to stop working.
This patch adds a SSDT extension for the PCI device if it is hidden from
the OS and reports the occupied resource via ACPI to the OS. For the
cases where the device is hidden later at coreboot runtime and therefore
is not marked as hidden in the PCI device itself a Kconfig switch called
'FAST_SPI_GENERATE_SSDT' is introduced. It defaults to 'no' and can be
set from SOC code to override it.
Since there is no defined ACPI ID for the fast SPI controller available
now, the generic one (PNP0C02) is used.
Test: Boot mc_apl4 and make sure flashrom works again.
Change-Id: Ia16dfe6e001188aad26418afe0f04c53ecfd56f1
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/64076
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sean Rhodes <sean@starlabs.systems>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Use defines for a better reading of the code.
Change-Id: I8e696240d649c0ea2341b8f04b62eebffebc1d57
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/64519
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
By right if PseTsnGbeSgmiiEnable is disable,
PseTsnGbePhyInterfaceType should use RGMII setting.
Signed-off-by: Lean Sheng Tan <sheng.tan@9elements.com>
Change-Id: If593a5534716a9e93f99cb155fb5e86e12b1df17
Reviewed-on: https://review.coreboot.org/c/coreboot/+/64477
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
|
|
There are efforts to have bootflows that do not follow a traditional
bootblock-romstage-postcar-ramstage model. As part of that CBMEM
initialisation hooks will need to move from romstage to bootblock.
The interface towards platforms and drivers will change to use one of
CBMEM_CREATION_HOOK() or CBMEM_READY_HOOK(). Former will only be called
in the first stage with CBMEM available.
Change-Id: Ie24bf4e818ca69f539196c3a814f3c52d4103d7e
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63375
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Reuse existing SMBus code from southbridge/intel/common/smbus_ops.h.
Change-Id: Iea4f6886bb49590f7f96abbfbe631ac9d4dda902
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/64432
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Follow this commit 95986169f (soc/intel/alderlake: Skip FSP Notify APIs)
to skip FSP Notify APIs.
Elkhart Lake SoC deselects Kconfigs as below:
- USE_FSP_NOTIFY_PHASE_READY_TO_BOOT
- USE_FSP_NOTIFY_PHASE_END_OF_FIRMWARE
to skip FSP notify APIs (Ready to boot and End of Firmware) and make
use of native coreboot driver to perform SoC recommended operations
prior booting to payload/OS.
When deselecting these Kconfigs, cse_final_ready_to_boot() and
cse_final_end_of_firmware() in the common cse driver will be used
instead as required operations to perform prior to booting to OS.
Check out this CL for further info:
commit 90e318bba (soc/intel/common/cse: Add `finalize` operation for
CSE)
Additionally, create a helper function `heci_finalize()` to keep HECI
related operations separated for easy guarding again config.
Signed-off-by: Lean Sheng Tan <sheng.tan@9elements.com>
Change-Id: I477c204233f83bc96fd5cd39346bff15ed942dc6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63762
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Remove two redundant `void *` casts in `clrsetbits32()` calls. In
addition, preemptively retype the `io_mem_base` variable in order
to avoid having to add casts in future commits.
Change-Id: Iae9c8189a6f8cd29181c52c2241789c6d392d77b
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/64398
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
|
|
This patch adds the support to enable the external V1P05/Vnn rails
in S0 state via devicetree.
BUG=b:223102016
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Change-Id: I555e5607af15a5f5d83ef74321b1b71f17cca289
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63497
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Kangheui Won <khwon@chromium.org>
|
|
This patch updates the VccIn Aux Imon IccMax for ADL-N to SOC SKU
specific value of 27A.
Kit: 646929 - ADL N Platform Design Guide
BUG=b:223102016
TEST=Verified that VccIn Aux Imon IccMax value is set to 27mA.
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Change-Id: If09cd1112fac9b30ff04c45aa5a6062c2513c715
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63372
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
This patch configures the SKU specific power delivery parameters for the
VR domains for ADL-N.
+--------------+-------+-------+-------+-------+-----------+--------+
| SKU |Setting| AC LL | DC LL |ICC MAX|TDC Current|TDC Time|
| | |(mOhms)|(mOhms)| (A) | (A) | (msec)|
+--------------+-------+-------+-------+-------+-----------+--------+
|ADL-N 081 | IA | 4.7 | 4.7 | 53 | 22 | 28000 |
+ +-------+-------+-------+-------+-----------+--------+
| | GT | 6.5 | 6.5 | 29 | 22 | 28000 |
+--------------+-------+-------+-------+-------+-----------+--------+
|ADL-N 081(7W) | IA | 5.0 | 5.0 | 37 | 14 | 28000 |
+ +-------+-------+-------+-------+-----------+--------+
| | GT | 6.5 | 6.5 | 29 | 14 | 28000 |
+--------------+-------+-------+-------+-------+-----------+--------+
|ADL-N 041(6W) | IA | 5.0 | 5.0 | 37 | 12 | 28000 |
+ Pentium +-------+-------+-------+-------+-----------+--------+
| | GT | 6.5 | 6.5 | 29 | 12 | 28000 |
+--------------+-------+-------+-------+-------+-----------+--------+
|ADL-N 041(6W) | IA | 5.0 | 5.0 | 37 | 12 | 28000 |
+ Celeron +-------+-------+-------+-------+-----------+--------+
| | GT | 6.5 | 6.5 | 26 | 12 | 28000 |
+--------------+-------+-------+-------+-------+-----------+--------+
|ADL-N 021(6W) | IA | 5.0 | 5.0 | 27 | 10 | 28000 |
+ +-------+-------+-------+-------+-----------+--------+
| | GT | 6.5 | 6.5 | 23 | 10 | 28000 |
+--------------+-------+-------+-------+-------+-----------+--------+
Kit: 646929 - ADL N Platform Design Guide -> Power_Map_Rev1p0
BUG=b:223102016
TEST=Boot and verify the UPD values are configured properly for ADL-N SKU's.
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Change-Id: I3d6ae20323d3e859f52228822d4cbad143921a37
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63369
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
|
There are two APL specific config switches for RAPL and min. cpu clock
(APL_SKIP_SET_POWER_LIMITS, APL_SET_MIN_CLOCK_RATIO). These switches
could be used in future in other CPU platforms. Move them to common code
instead of having them just for one SOC.
Test: Make sure that the clock ratio (MSR 0x198) and the RAPL settings
(MSR0x610) do not change with this patch applied on mc_apl{1,4,5}
mainboard.
Change-Id: I3d63d1b9b6c96586a3c20bf8c1d8001b1d7c4bed
Signed-off-by: Uwe Poeche <uwe.poeche@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63546
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
Remove devicetree options that aren't used anywhere in the code.
Change-Id: I7eace61079e14423325332d277fdda4f986fd133
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/64403
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Program the `SmbusEnable` FSP UPD according to the SMBus PCI device's
state in the devicetree. This avoids having to manually make sure the
SMBus PCI device and the `SmbusEnable` setting are in sync.
Change-Id: I275a981f914a55dc57a75e7d436912ff0255a293
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/64402
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Hook up the hyper-threading setting from the FSP to the option API so
that related mainboards don't have to do that. Unless otherwise
configured (e.g. the CMOS setting or overriden by the mainboard code),
the value from the Kconfig setting `FSP_HYPERTHREADING` is used.
Also, remove related code from the mainboard kontron/bsl6, since it is
obsolete now.
Change-Id: I1023d1b94acb63f30455c56b394b68059deaaa16
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/60542
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
This patch provides the functionality to change the TSN GbE MAC
addresses. Prerequisite for this is a mainboard specific function that
returns a matching MAC address.
A test was performed with the next patch in the series, which enables
the TSN GbE driver for mc_ehl2 mainboard.
Change-Id: I2303a64cfd09fa02734ca9452d26591af2a76221
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63863
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
To be able to make EHL Ethernet GbE-TSN Controller configurable, a
driver is required. Functionality comes in following patches.
Change-Id: I7522914c56b74486bb088280d2686acf7027d1d3
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63861
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
Add Raptor Lake specific CPU, System Agent, PCH, IGD device IDs.
References:
RaptorLake External Design Specification Volume 1 (640555)
600/700 Series PCH External Design Specification Volume 1 (626817)
Change-Id: I39e655dec2314a672ea63ba90d8bb3fc53bf77ba
Signed-off-by: Bora Guvendik <bora.guvendik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63750
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Anil Kumar K <anil.kumar.k@intel.com>
|
|
Starting with Meteor Lake SoC, the PCR/DMI interface to program GPMR
is replaced with IOC (I/O Cache), hence, this patch implements IOC
driver to support that migration.
Reference: 643504 MTL FAS section 7.5.2
TEST=Build and boot to OS for TGL RVP and MTL PSS
Signed-off-by: Wonkyu Kim <wonkyu.kim@intel.com>
Change-Id: I768027c2ca78310c03845f70f17df19dc8cd0982
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63198
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The fast SPI controller (usually handling the boot NOR flash) is a
different controller type than the generic SPI controllers as it
provides access to the boot flash and usually is not used for generic
SPI slave connections.
Though there is common code for the fast SPI controller it currently do
not uses the PCI driver structure. This patch adds the PCI driver
envelope to the fast SPI driver and moves Apollo Lake as the first
platform to this driver.
Change-Id: I31bf39ec1c622db887dec9ca8623a7f282402849
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/64075
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Setting up postcar MTRRs is done when invd is already called so there
is no reason to do this in assembly anymore.
This also drops the custom code for Quark to set up MTRRs.
TESTED on foxconn/g41m and hermes/prodrive that MTRR are properly set
in postcar & ramstage.
Change-Id: I5ec10e84118197a04de0a5194336ef8bb049bba4
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54299
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: If9ae375629c8af3d32b4c5493b5d63203e8847aa
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/64360
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
|
|
GNVS is more fragile as you need to keep struct elements in sync with
ASL code.
Change-Id: I2cd5e6b56e4a0dbbb11f4a0ac97e8f84d53b90ec
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/64216
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
The "No memory dimm at address" line in get_spd_sn and get_spd fucntion
have different format of SPD address.
get_spd_sn shows a 8-bit address format but get_spd shows a 7-bit
address format when there is no DIMM connected. It can be confusing
when debugging.
Change-Id: I46a006f4024b12d27ae0a933b7c40515034d5d64
Signed-off-by: Kane Chen <kane.chen@intel.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/64290
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jamie Chen <jamie.chen@intel.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
There were 3 different functions in gpio.c file which used to
get gpio group and pin information separately through function
calls.
Since these are static function, we can modify argument to
pass group and pin information from parent/calling function.
This will reduce redundant work of getting information 3 times
separately.
BUG=None
BRANCH=None
TEST=code compiles and correct information is passed to functions.
Check by using pin information on Brya.
Change-Id: Ie92be8c22838ebc5e831be58545e2023eecfff24
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/64231
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Since coreboot locks GPIO registers after GPIO configuration, OS is not
able to program GPE_EN register to program wake events. This causes
the issue of event not getting logged into event log (since GPE_EN bit
is not set).
GPE_EN register programming is required for the GPIO pins which are
capable of generating SCI for the system wake. Elog mechanism relies
on GPE_EN and GPE_STS bit to log correct wake signal.
This patch add supports to program GPE_EN register before coreboot locks
the GPIO registers. Note that coreboot will only program GPE_EN bits for
GPIO capable of generating SCI.
This will help resolve issue where we don't see wake event GPIO in event
log.
BUG=b:222375516
BRANCH=firmware-brya-14505.B
TEST=Compile code for Brya and see GPE_EN bits set from the kernel console
Change-Id: I27e525f50c374c2cc9675e77eaa7774683a6e7c2
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/64089
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
coreboot needs to set GPE_EN bit for the GPIOs which are wake capable
from s0ix/sleep. Due to GPIO locking mechanism, coreboot/OS will not
be able to write GPE_EN register post GPIO has been locked.
This patch adds support in SoC code to provide correct offset for
GPE_EN and GPE_STS registers to the common code.
Plan is to use this offsets to set GPE_EN bits before GPIO locking
in coreboot which will be part of subsequent CL.
BUG=b:222375516
BRANCH=firmware-brya-14505.B
TEST=Check if code compiles for Brya and correct offset values are printed.
Change-Id: I6b813b30b8b360f8eccbf539b57387310e380560
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/64088
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
By using mp_run_on_all_cpus_synchronously to run APs MTRR init, it
gurantees the BSP will run post_cpus_add_romcache until all APs finishes
_x86_setup_mtrrs task.
BUG=b:225766934
TEST=Test on redrix and found the MTRR race condition on AP/BSP is gone.
Change-Id: I1fd889f880a0c605e6c739423a434d2adbc12d26
Signed-off-by: Kane Chen <kane.chen@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63567
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Signed-off-by: Shelly Chang <Shelly_Chang@wiwynn.com>
Change-Id: Ib795f25abe5bbd95555b68af39c637d7c93aa819
Reviewed-on: https://review.coreboot.org/c/coreboot/+/64251
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Found using:
diff <(git grep -l '#include <cpu/x86/pae.h>' -- src/) <(git grep -l 'memset_pae\|MEMSET_PAE_\|MAPPING_ERROR\|map_2M_page\|paging_identity_map_addr\|paging_enable_for_car\|paging_set_default_pat\|paging_set_pat\|PAT_ENCODE\|PAT_UC_MINUS\|PAT_WB\|PAT_WP\|PAT_WT\|PAT_WC\|PAT_UC\|paging_set_nxe\|paging_disable_pae\|paging_enable_pae\|paging_enable_pae_cr3' -- src/)
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Change-Id: If0f69fa8fe4a336b4e4d2a148d1e7a911af3c2c9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63829
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <gaumless@tutanota.com>
|
|
Found using:
diff <(git grep -l '#include <cf9_reset.h>' -- src/) <(git grep -l 'RST_CNT\|FULL_RST\|RST_CPU\|SYS_RST\|do_system_reset\|do_full_reset\|cf9_reset_prepare\|system_reset\|full_reset' -- src/) |grep "<"
Change-Id: I093d8412e14ce81b462fb9a7ccb3a2a93ae760a6
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/60803
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <gaumless@tutanota.com>
|
|
Change-Id: I25d112941db8214a7e450de5fb512ef8c2c5f5e2
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61006
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <gaumless@tutanota.com>
|
|
Change-Id: I322a94186b92033fc27ba97785b55df09aa317f7
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/61009
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <gaumless@tutanota.com>
|
|
Clang does not like array declarations inside plain switch cases. There
are 2 options to fix this: use a block inside the switch statement, or
declare it outside the switch statement. This does the latter.
Change-Id: I9a02136fd63ac171b2bec4647c30c7eece930246
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/64349
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
|
|
The bootblock is loaded from IFWI so there is no need to have it in
cbfs.
Also remove the FIT handling as that is also handled by the IFWI.
TESTED: up/squared still boots
Change-Id: I8e70e080765dd7306074a8cf71c8795b8fbbb8a2
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63225
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I2b02bcecda2257f191c0d0fc9935b1eb673ab3d2
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/64335
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
|
|
CID 1488814: Uninitialized variables (UNINIT)
Commit c66ea98 introduced an issue after static analysis on merge.
Because every APIC is associated with a CPU, this did not result in
any issues at runtime but should be fixed/cleaned up. Now, the path
name is initialized to null.
Fixes: Coverity CID 1488814, commit c66ea98
TEST=Built on brya
Change-Id: I0cfc8fd7a0c39e6610a9361630e3755293084f3d
Signed-off-by: Tarun Tuli <taruntuli@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/64336
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Change-Id: I3c8c1787c77ed08942c6550ca556875904be2fa2
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/64242
Reviewed-by: Jonathan Zhang <jonzhang@fb.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I2acad0763d19b50c02472dfdd33084acbafe4c84
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/64241
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
|
|
Change-Id: Ifc0374ed49ecefc57dec8e72e73bac031838a9f5
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/64238
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I2f89d11c163f56163d5c361a3edad14418bf9fa7
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/64237
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
This fixes building with clang.
Change-Id: I7405f031298a35589e435e888af911d916662d23
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63069
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Clang does not like static asserts on integral constant expressions.
Change-Id: If5890a357ed95153d8ae2efa727c111b05bc6455
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63066
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Implement sub-function 1 (Get Device Constraints)
of the Low Power S0 Idle Device-Specific Method (_DSM).
This provides a way in which to describe various devices required
D-states to enter LPM (S0ix). The information can be used to help
in diagnostics and understanding of S0ix entry failure.
Values were derived from Intel document 595644 (rev 0.45) and
the ADL FSP sample ASL.
This implementation adds support for ADL. Other SoC's could be
ported to be included as well. If they aren't, they will default
to the existing behavior of a single hardcoded device to ensure
compatibility with Windows.
TEST=Built and tested on brya by verifying SSDT contents
Change-Id: Ibe46a0583c522a8adf0a015cd3a698f694482437
Signed-off-by: Tarun Tuli <taruntuli@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63969
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Lance Zhao
|
|
This also adds messages when adding the files.
Change-Id: Ie812084cc243a18cbc2913804ef2190dd9d6ed9b
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63224
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Change-Id: I41bbdabf7b846386651e64f4afb5b7b9fb38e1cb
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56118
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <gaumless@tutanota.com>
Reviewed-by: Sean Rhodes <sean@starlabs.systems>
|
|
Clang complains about this.
Change-Id: I421d6c5daa373d1537e4ac2243438e7f1f6208d1
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63067
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
A few ACPI device path name handlers are missing. Add handling
to ensure that these names are returned during acpi_device_path()
calls.
TEST=Built and tested on brya
Signed-off-by: Tarun Tuli <taruntuli@google.com>
Change-Id: I37d6dd5df921c931af72dd469c3f4067c61b0df3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63984
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Add an enum for `DdiPortXConfig` devicetree options. Note that setting
these options to zero does not disable the corresponding DDI port, but
instead indicates that no LFP (Local Flat Panel, i.e. internal LCD) is
connected to it.
Change-Id: I9ea10141e51bf29ea44199dcd1b55b63ec771c0a
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/64047
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Tim Crawford <tcrawford@system76.com>
|
|
This patch calls into the PMC IPC function that informs about PMC
enumeration.
Note: Alder Lake FSP Notify Phase 1 callback missed to send this PMC
IPC, hence, this patch is considered as an improvement over FSP Notify
Phase API.
BUG=b:211954778
TEST=Able to build and boot google/redrix to OS without any PMC IPC
error.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I43cfad25a5861c5aa5dae293ff42c9cefe862ea2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63954
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
|
|
This patch sends an IPC to PMC to inform about PCI enumeration.
BUG=b:211954778
TEST=Able to build and boot google/redrix to OS.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I77d428f9501feaccab8bb431090d10ce8d3af9b2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63953
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
|
|
pmc_prev_sleep_state() isn't handling the case where acpi_sleep_from_pm1()
returns ACPI_S4. Pass that value along so it can get set as a
prev_sleep_state. Without this, consumers see prev_sleep_state as 0
and always treat resume as a cold boot. With this, consumers can
correctly do behavior specific to S4 resume, like skipping the
disconnect IPC command to the PMC on Alderlake systems.
BUG=b:230031158
TEST=Resume from S4 on Primus4es
Signed-off-by: Evan Green <evgreen@chromium.org>
Change-Id: I3fb3dc428a749db80293e51a04a2096514a7b689
Reviewed-on: https://review.coreboot.org/c/coreboot/+/64002
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Use common ASL defines for POST code handling.
Change-Id: I5b4c11860a8c33e56edaea0f6de378cbaa63a8c5
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63989
Reviewed-by: Jonathan Zhang <jonzhang@fb.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Move ASL POST code declarations into a common file to avoid redundancy.
Also, provide a dummy implementation when `POST_IO` is not enabled, as
the value of `CONFIG_POST_IO_PORT` can't be used.
Change-Id: I891bd8754f10f16d618e76e1ab88c26164776a50
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63988
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
|
|
ADL-S CPU has maximum 3 PCIe interfaces when the x16 link is bifurcated
into two x8 links. ADL-S PCH has up to 28 PCIe Root Ports, 18 CLKOUT and
CLKREQ signals. ADL-S CPUs do not have Thunderbolt.
Based on the Intel DOC #619501 and #619362.
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Change-Id: I408c815d5a43c081beb3f84d795c2b863ce33eb2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63457
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Notify IOM to enable or disable TBT displays on S0ix exit and entry
respectively.
Change-Id: I9f49d8e30fe8e8b335128e53d71ef902328f031a
Signed-off-by: Michał Kopeć <michal.kopec@3mdeb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63980
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Krystian Hebel <krystian.hebel@3mdeb.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Add display on and off notifications which call mainboard hooks if
present. This allows to handle some board specific functions in user
absence or presence (when display goes off from inactivity or on from
activity).
TEST=Use Display on/off notification on Clevo NV41 to tell EC about
laptop inactivity. It is necessary to properly handle S0ix entry (stop
the fans and start blinking the power led).
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Signed-off-by: Michał Kopeć <michal.kopec@3mdeb.com>
Change-Id: Ie80f631ecffa74467ab6d6162e552ba977f7e3f4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62494
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Krystian Hebel <krystian.hebel@3mdeb.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
This patch avoids sending the `Get Boot perf` command while booting
with CSE device hidden.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I498c14d144295a9bc694b90060ca74c66966d65e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63867
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Bora Guvendik <bora.guvendik@intel.com>
|
|
Now the bootblock is not limited to 64K so integrating vboot into the
bootblock reduces the binary size. intel/apl is an exception since the
bootblock size is limited to 32K.
Change-Id: I5e02961183b5bcc37365458a3b10342e5bc2b525
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52788
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
This patch enforces disabling of the CSE device if CSE stays in
SOFT TEMP DISABLE state. The recommendation is to make CSE function
disable to avoid receiving any CSE commands from the OS layer.
BUG=b:228789015
TEST=None
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I77c254195895a93a5606adee8b6f43d8b7100848
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63822
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
This patch removes redundant DISABLE_HECI1_AT_PRE_BOOT config check for
heci1_disable(), once by caller (from various SoC) and again inside the
callee (heci1_disable) function.
As all callers of heci1_disable() function are doing
DISABLE_HECI1_AT_PRE_BOOT config enabled check, hence, the second check
inside the callee can be dropped.
BUG=b:228789015
TEST=Able to build and boot google/redrix with this change. CSE PCI
device is getting function disabled upon selecting
DISABLE_HECI1_AT_PRE_BOOT from SoC config.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I47d7a9989e355987618d089f79c3340fcf4953ad
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63821
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
This patch decouples HECI disabling interface a.k.a SMM or PCR or PMC
IPC etc. from DISABLE_HECI1_AT_PRE_BOOT kconfig as Intel ME BWG
recommends to disable the CSE PCI device while CSE is in
software temporary disable state.
BUG=b:228789015
TEST=Able to build google/redrix.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I66abc04d5e195515165a77b0166d004f17d029e7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63823
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Kangheui Won <khwon@chromium.org>
|
|
Use PCIEXBAR_PCIEXBAREN instead of constant value(1)
Signed-off-by: Wonkyu Kim <wonkyu.kim@intel.com>
Change-Id: Ica9e8162945da0a714822c37753914575c26024e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63878
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Revert CdClock setting and use default value 0xff.
Previous problem was fixed by Jasperlake FSP in version 1.3.09.31,
so we can use the original CdClock setting in baseboard.
BUG=b:206557434
BRANCH=dedede
TEST="Built and verified on magolor platform to confirm FSP solution works"
Cq-Depend: chrome-internal:4662167
Change-Id: I50d65e0caaf8f3f074322cff5bbdc68bdb1bbf78
Signed-off-by: Simon Yang <simon1.yang@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63808
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Henry Sun <henrysun@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
`sa_lockdown_cfg` function ensures locking the PAM register hence,
skip dedicated calling into `sa_lock_pam()` from the SoC
`finalize.c` file. Dropped sa_lock_pam() call from ADL/CNL/EHL/JSL
and TGL.
Additionally, this patch enforces SA lockdown configuration for SKL
and ICL as well.
BUG=b:211954778
TEST=Able to build google/brya with these changes.
> localhost ~ # lspci -xxx | less
00:00.0 Host bridge: Device 8086:4601 (rev 04)
Bit 0 for all PAM registers a.k.a, PAMx_0_0_0_PCI.LOCK bit is set
(meaning locked).
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: Ibd464d2507393ed0c746eb1fbd10e36092ed5599
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63518
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
|
|
Commit 211be9c03 (soc/intel/cmn/{block, pch}: Migrate GPMR driver)
drops `dmi` prefix from `lockdown_cfg` function name.
This patch adds the `gpmr` prefix to the lockdown_cfg function to make
it meaningful.
BUG=b:211954778
TEST=Able to build google/brya.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: Idaa0e089131ab125348e2430355041c4ee7971de
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63789
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
|
|
Alder Lake SoC deselects USE_FSP_NOTIFY_PHASE_POST_PCI_ENUM Kconfig
to skip FSP notify API (Post PCI Enumeration) and make use of native
coreboot driver to perform SoC recommended operations prior booting to
payload/OS.
BUG=b:211954778
TEST=Able to build brya with these changes and coreboot log with this
code change as below when ADL SoC selects required configs.
[INFO ] coreboot skipped calling FSP notify phase: 00000020.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I46f6ca791fb60b417d205d0a54705f3481deebd4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63693
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
|
|
This patch implements a function to enable IOSF Primary Trunk Clock
Gating.
BUG=b:211954778
TEST=Able to build and boot google/redrix to OS.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: Ie28dde8f62adc5bafc4a42e608827f51da82570c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63692
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
This patch locks PMC features like: debug mode configuration and host
read access to PMC XRAM.
BUG=b:211954778
TEST=Able to build and boot google/redrix to OS.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I29178bdd9a94a24ca7056eb7377625f41a43c33c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63691
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
This patch performs locking of the PMC soft strap message interface.
BUG=b:211954778
TEST=Able to build and boot google/redrix to OS. Verified Bit 0 of PMC
MMIO register 0x104c is set as below.
> localhost ~ # iotools mmio_read32 0xfe00104c
0x00000001
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I1ae972a203affa54c03de71f0f702356334cbf7d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63690
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
This patch performs PMC static function lockdown.
BUG=b:211954778
TEST=Able to build and boot google/redrix to OS. Verified PMC static PG
lock (bit 31) is set.
> iotools mmio_read32 0xfe001e20
0x80000000
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I68343f9af4f34aceae06293c5f87c5eaa3430a60
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63689
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
The unit of dram speed is MT/s so append it on variable name.
BUG=b:229549930
BRANCH=none
TEST=build coreboot without error
Signed-off-by: Scott Chao <scott_chao@wistron.corp-partner.google.com>
Change-Id: I83c780440613050c0202f95d5f64991b61d9c280
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63735
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
|
There is a bug floating around where communciation with the PMC fails
after transitions through S3/S4/S5. This CL does not address that issue.
However in working with error cases presented by a failing PMC, we're
forced into an early return in read_pmc_lpm_requirements(), which sets
up _DSM buffers in the SSDT for the PEP device.
The function itself returns void, so the error is swallowed regardless.
However returning early is not the appropriate action because it causes
the size of the buffer written into the _DSM method to change. This causes
the SSDT to change size and layout across an S3 or S4 transition, which
results in mayhem in the kernel, as the kernel is not expecting these
tables to change out from under it.
Instead of returning early, it's better to simply print the error and
keep going, attaching a zeroed out buffer for the substate requirements.
This results in an empty requirements mask for all states. From what I
can see in the kernel this is no more broken than today's behavior, as
this buffer seems to only be used for printing a debugfs file.
In fact in this particular case the kernel doesn't even notice, as this
buffer is copied out at boot, and not refreshed at resume.
BUG=b:230031158
TEST=hibernate and resume on Primus4ES
Signed-off-by: Evan Green <evgreen@chromium.org>
Change-Id: Ibe35d50b350b1b96dea313dfcbd00745970c16ab
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63790
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
The patch adds support to control CSE Lite firmware update dynamically.
In order to disable the CSE firmware update functionality, offset 0xf00
in the coreboot binary be updated with 0x1.
Run below command on the binary to disable CSE firmwar update
printf '\x01' | dd of=image-brya4es.serial.bin bs=1 seek=3840 count=1
conv=notrunc
BUG=b:153410586
TEST=Verified CSE firmware update functionality is not getting
triggered after updating the offset:0xF00 in the coreboot binary.
........................ CB Logs ......................................
[DEBUG] prev_sleep_state 5
[DEBUG] cse_lite: Number of partitions = 3
[DEBUG] cse_lite: Current partition = RW
[DEBUG] cse_lite: Next partition = RW
[DEBUG] cse_lite: Flags = 0x3
[DEBUG] cse_lite: RO version = 16.0.15.1752 (Status=0x0, Start=0x2000,
End=0x19bfff)
[DEBUG] cse_lite: RW version = 16.0.15.1752 (Status=0x0,
Start=0x205000, End=0x439fff)
rt_debug: pre_mem_debug.cse_fw_update_disable=1
[DEBUG] Boot Count incremented to 956
.......................................................................
Signed-off-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Change-Id: I9f234b142191eb83137d5d83f21e890e1cb828ba
Reviewed-on: https://review.coreboot.org/c/coreboot/+/62715
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
|
|
The patch fixes the buggy code which tries to access the Descriptor
Region. The existing code doesn't use correct APIs to access the
Descriptor Region. Hence, error message is getting displayed during
the boot.
BUG=b:229003612
TEST=Build and verify no errors seen while accessing the Descriptor
Region.
Signed-off-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Change-Id: Ib144cc0845b7527e5a3032529b0802f961944b87
Reviewed-on: https://review.coreboot.org/c/coreboot/+/63734
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Found using:
diff <(git grep -l '#include <acpi/acpi.h>' -- src/) <(git grep -l 'SLP_EN\|SLP_TYP_SHIFT\|SLP_TYP\|SLP_TYP_S\|ACPI_TABLE_CREATOR\|OEM_ID\|ACPI_DSDT_REV_\|acpi_device_sleep_states\|ACPI_DEVICE_SLEEP\|RSDP_SIG\|ASLC\|ACPI_NAME_BUFFER_SIZE\|COREBOOT_ACPI_ID\|acpi_tables\|acpi_rsdp\|acpi_gen_regaddr\|ACPI_ADDRESS_SPACE\|ACPI_FFIXEDHW_\|ACPI_ACCESS_SIZE_\|ACPI_REG_MSR\|ACPI_REG_UNSUPPORTED\|ACPI_HID_\|acpi_table_header\|MAX_ACPI_TABLES\|acpi_rsdt\|acpi_xsdt\|acpi_hpet\|acpi_mcfg\|acpi_tcpa\|acpi_tpm2\|acpi_mcfg_mmconfig\|acpi_hmat\|acpi_hmat_mpda\|acpi_hmat_sllbi\|acpi_hmat_msci\|acpi_srat\|ACPI_SRAT_STRUCTURE_\|acpi_srat_lapic\|acpi_srat_mem\|acpi_srat_gia\|CPI_SRAT_GIA_DEV_HANDLE_\|acpi_slit\|acpi_madt\|acpi_lpit\|acpi_lpi_flags\|acpi_lpi_desc_type\|ACPI_LPI_DESC_TYPE_\|acpi_lpi_desc_hdr\|ACPI_LPIT_CTR_FREQ_TSC\|acpi_lpi_desc_ncst\|acpi_vfct_image_hdr\|acpi_vfct\|acpi_ivrs_info\|acpi_ivrs_ivhd\|acpi_ivrs\|acpi_crat_header\|ivhd11_iommu_attr\|acpi_ivrs_ivhd_11\|dev_scope_type\|SCOPE_PCI_\|SCOPE_IOAPIC\|SCOPE_MSI_HPET\|SCOPE_ACPI_NAMESPACE_DEVICE\|dev_scope\|dmar_type\|DMAR_\|DRHD_INCLUDE_PCI_ALL\|ATC_REQUIRED\|DMA_CTRL_PLATFORM_OPT_IN_FLAG\|dmar_entry\|dmar_rmrr_entry\|dmar_atsr_entry\|dmar_rhsa_entry\|dmar_andd_entry\|dmar_satc_entry\|acpi_dmar\|acpi_apic_types\|LOCAL_APIC,\|IO_APIC\|IRQ_SOURCE_OVERRIDE\|NMI_TYPE\|LOCAL_APIC_NMI\|LAPIC_ADDRESS_\|IO_SAPIC\|LOCAL_SAPIC\|PLATFORM_IRQ_SOURCES\|LOCAL_X2APIC\|GICC\|GICD\|GIC_MSI_FRAME\|GICR\|GIC_ITS\|acpi_madt_lapic\|acpi_madt_lapic_nmi\|ACPI_MADT_LAPIC_NMI_ALL_PROCESSORS\|acpi_madt_ioapic\|acpi_madt_irqoverride\|acpi_madt_lx2apic\|acpi_madt_lx2apic_nmi\|ACPI_DBG2_PORT_\|acpi_dbg2_header\|acpi_dbg2_device\|acpi_fadt\|ACPI_FADT_\|PM_UNSPECIFIED\|PM_DESKTOP\|PM_MOBILE\|PM_WORKSTATION\|PM_ENTERPRISE_SERVER\|PM_SOHO_SERVER\|PM_APPLIANCE_PC\|PM_PERFORMANCE_SERVER\|PM_TABLET\|acpi_facs\|ACPI_FACS_\|acpi_ecdt\|acpi_hest\|acpi_hest_esd\|acpi_hest_hen\|acpi_bert\|acpi_hest_generic_data\|acpi_hest_generic_data_v300\|HEST_GENERIC_ENTRY_V300\|ACPI_GENERROR_\|acpi_generic_error_status\|GENERIC_ERR_STS_\|acpi_cstate\|acpi_sw_pstate\|acpi_xpss_sw_pstate\|acpi_tstate\|acpi_lpi_state_flags\|ACPI_LPI_STATE_\|acpi_lpi_state\|acpi_upc_type\|UPC_TYPE_\|acpi_ipmi_interface_type\|IPMI_INTERFACE_\|ACPI_IPMI_\|acpi_spmi\|ACPI_EINJ_\|ACTION_COUNT\|BEGIN_INJECT_OP\|GET_TRIGGER_ACTION_TABLE\|SET_ERROR_TYPE\|GET_ERROR_TYPE\|END_INJECT_OP\|EXECUTE_INJECT_OP\|CHECK_BUSY_STATUS\|GET_CMD_STATUS\|SET_ERROR_TYPE_WITH_ADDRESS\|TRIGGER_ERROR\|READ_REGISTER\|READ_REGISTER_VALUE\|WRITE_REGISTER\|WRITE_REGISTER_VALUE\|NO_OP\|acpi_gen_regaddr1\|acpi_einj_action_table\|acpi_injection_header\|acpi_einj_trigger_table\|set_error_type\|EINJ_PARAM_NUM\|acpi_einj_smi\|EINJ_DEF_TRIGGER_PORT\|FLAG_PRESERVE\|FLAG_IGNORE\|EINJ_REG_MEMORY\|EINJ_REG_IO\|acpi_einj\|acpi_create_einj\|fw_cfg_acpi_tables\|preload_acpi_dsdt\|write_acpi_tables\|acpi_fill_madt\|acpi_fill_ivrs_ioapic\|acpi_create_ssdt_generator\|acpi_write_bert\|acpi_create_fadt\|acpi_fill_fadt\|arch_fill_fadt\|soc_fill_fadt\|mainboard_fill_fadt\|acpi_fill_gnvs\|acpi_fill_cnvs\|update_ssdt\|update_ssdtx\|acpi_fill_lpit\|acpi_checksum\|acpi_add_table\|acpi_create_madt_lapic\|acpi_create_madt_ioapic\|acpi_create_madt_irqoverride\|acpi_create_madt_lapic_nmi\|acpi_create_madt\|acpi_create_madt_lapics\|acpi_create_madt_lapic_nmis\|acpi_create_madt_lx2apic\|acpi_create_srat_lapic\|acpi_create_srat_mem\|acpi_create_srat_gia_pci\|acpi_create_mcfg_mmconfig\|acpi_create_srat_lapics\|acpi_create_srat\|acpi_create_slit\|acpi_create_hmat_mpda\|acpi_create_hmat\|acpi_create_vfct\|acpi_create_ipmi\|acpi_create_ivrs\|acpi_create_crat\|acpi_create_hpet\|acpi_write_hpet\|generate_cpu_entries\|acpi_create_mcfg\|acpi_create_facs\|acpi_create_dbg2\|acpi_write_dbg2_pci_uart\|acpi_create_dmar\|acpi_create_dmar_drhd\|acpi_create_dmar_rmrr\|acpi_create_dmar_atsr\|acpi_create_dmar_rhsa\|acpi_create_dmar_andd\|acpi_create_dmar_satc\|cpi_dmar_\|acpi_create_\|acpi_write_hest\|acpi_soc_get_bert_region\|acpi_resume\|mainboard_suspend_resume\|acpi_find_wakeup_vector\|ACPI_S\|acpi_sleep_from_pm1\|acpi_get_preferred_pm_profile\|acpi_get_sleep_type\|acpi_get_gpe\|permanent_smi_handler\|acpi_s3_resume_allowed\|acpi_is_wakeup_s3\|acpi_align_current\|get_acpi_table_revision' -- src/) |grep "<"
Change-Id: Ibc5d5883d9ec6ee55797bd36178af622d08e4f9b
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/60631
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <martinroth@google.com>
|
