| Age | Commit message (Collapse) | Author |
|---|
|
The serial IRQ (SERIRQ) used by the LPC interface can operate either in
continuous or in quiet mode. Add a Kconfig switch to select the desired
mode. This switch can now be used on mainboard level to enable the
needed mode per mainboard.
Change-Id: Ibe246b88164a622f9c71ebe7bab752a083a49a62
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/16575
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Since this mainboard provides 4 COM ports on LPC, enable decoding of
the corresponding addresses using the generic LPC decode registers.
Change-Id: I0e93d40dca01d55f3567a18c7ec02269e3bec466
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/16535
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
The serial IRQ configuration register is only 8 bit wide so switch the
PCI access from 16 bits to 8 bits.
Change-Id: Ia9fbc02251e00b31440bf103e2afc2ff285b7f2e
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/16534
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Provide iosf and GPIO functions for GPIO address
calculation.
BUG=chrome-os-partner:55877
Change-Id: I6eaa1fcecf5970b365e3418541c75b9866959f7e
Signed-off-by: Vaibhav Shankar <vaibhav.shankar@intel.com>
Reviewed-on: https://review.coreboot.org/16349
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
For an unknown reason the printed address in the SPI debug messages is
modified before it is printed by subtracting the constant 0xf020 from
the passed in address.
What I suppose this debug code should do is to print the used register
address within the SPI controller while any parts of this address that
belongs to the SPI base address should be omitted. To fix that remove
the subtraction of 0xf020 and adjust the address mask to 0x3ff so that
only the offset to the registers inside the SPI controller will be
visible in the debug messages.
In addition switch to uint8_t and friends over u8 to sync up with used
types in this file.
Change-Id: I93ba7119873115c7abc80a214cc30363a6930b3b
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/16500
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: York Yang <york.yang@intel.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
BUG=chrome-os-partner:56034
Change-Id: Id88d262b32dea468536575117fc34d52076a3096
Signed-off-by: Venkateswarlu Vinjamuri <venkateswarlu.v.vinjamuri@intel.com>
Reviewed-on: https://review.coreboot.org/16423
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Use the config switch CONFIG_DEBUG_SPI_FLASH on compiler level rather
then on preprocessor level to ensure that the code is compiled even if
the switch is not selected. In addition the following two changes are
introduced:
1. Prepend the debug messages with 'SPI:' to make the output more
meaningful.
2. Change the address mask from 0xffff to 0x3ff and remove the subtraction
of the constant value 0xf020 in order to print only the register
offset within the SPI controller and avoid the visibility of any
fragments from SPI base address.
3. Switch to uint8_t and friends instead of u8 to sync up with other
code in the same file.
Change-Id: Iaf46f29a775039007a402fe862839df06a4cbfaa
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/16499
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
The pull up for CLKRUN is required to resolve keyboard slowness
and malfunctioning observed on some reef systems. The CLKRUN
signal was probed and found to be floating when the pull up
was not enabled. Also Added pull ups for the LPC Multiplexed
command, address and data lines LAD0:3 because the LPC
Interface specification requires them.
BUG=chrome-os-partner:55586
BRANCH=none
TEST=When a key is pressed, the character is immediately visible
on the screen. Also the interrupt count for i8042 increments
immediately in /proc/interrupts.
Change-Id: I16df1a0301a3994c926a609f61291761219f9e01
Signed-off-by: Shamile Khan <shamile.khan@intel.com>
Reviewed-on: https://review.coreboot.org/16426
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
|
|
Commit 93ef3ff makes the following only print the part number when
the ROM is built. In Makefile.inc, $(MAINBOARDDIR) is the variable
that has the quotes stripped off from $(CONFIG_MAINBOARD_DIR), so
use it instead of $(MAINBOARD_DIR).
build_complete:: coreboot
printf "\nBuilt %s (%s)\n" $(MAINBOARD_DIR) \
$(CONFIG_MAINBOARD_PART_NUMBER)
Change-Id: I729a583182937db7a926eb75aa28dfb53360046c
Signed-off-by: Iru Cai <mytbk920423@gmail.com>
Reviewed-on: https://review.coreboot.org/16410
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Increase the default timeout in the LPSS I2C driver to 4ms
from 2ms. During testing with some slower devices I found
that the existing timeout could be too short leading to
transaction failures.
Change-Id: Ied86c7a0aa26d55b31f447c5938803c194d0045e
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/16392
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
FSP header files should be located in vendorcode, not soc directory.
This patch includes changes any references to the old location to
the new location.
Change-Id: I44270392617418ec1b9dec15ee187863f2503341
Signed-off-by: Brandon Breitenstein <brandon.breitenstein@intel.com>
Reviewed-on: https://review.coreboot.org/16310
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
The following patch is based off of the UEFI 2.6 patch. The FSP header files
are temporarily staying in soc/intel/apollolake and FspUpd.h has been relocated
since the other headers expect it to be in the root of an includable directory.
Any struct defines were removed since they are defined in the headers and no
longer need to be explicity declared as struct with the UEFI 2.6 includes.
BUG=chrome-os-partner:54100
BRANCH=none
TEST=confirmed coreboot builds successfully
Change-Id: I10739dca1b6da3f15bd850adf06238f7c51508f7
Signed-off-by: Brandon Breitenstein <brandon.breitenstein@intel.com>#
Signed-off-by: Andrey Petrov <andrey.petrov@intel.com>
Reviewed-on: https://review.coreboot.org/16308
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
All but ga-g41m-es2l/cmos.default had multiple final newlines.
ga-g41m-es2l/cmos.default had no final newline.
Change-Id: Id350b513d5833bb14a2564eb789ab23b6278dcb5
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/16361
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Antonello Dettori <dev@dettori.io>
|
|
Instead of using a mix of _N and _NORTH, _NW and _NORTHWEST for GPIO
community names, follow one single convention. This allows for re-using
macros easily.
Change-Id: Icd9cf9ef70d03576d864688cf5d6946124c259c3
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/16353
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Change-Id: Ifc47f103492a2cd6c818dfd64be971d34afbe0a4
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/16324
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Add Initial pieces of code to support fsp2.0 in skylake keeping
the fsp1.1 flow intact.
The soc/romstage.h and soc/ramstage.h have a reference to
fsp driver includes, so split these header files for
each version of FSP driver.
Add the below files,
car_stage.S:
Add romstage entry point (car_stage_entry).
This calls into romstage_fsp20.c and aslo handles
the car teardown.
romstage_fsp20.c:
Call fsp_memory_init() and also has the callback
for filling memory init parameters.
Also add monotonic_timer.c to verstage.
With this patchset and relevant change in kunimitsu mainboard,
we are able to boot to romstage.
TEST= Build and Boot Kunimitsu with PLATFORM_USES_FSP1_1
Build and Boot Kunimitsu to romstage with PLATFORM_USES_FSP2_0
Change-Id: I4309c8d4369c84d2bd1b13e8ab7bfeaaec645520
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/16267
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
|
|
Certain LPDDR4 models have some HW issues that can be worked around
by turning off Periodic Retraining feature in the memory controller.
Add option to disable PR per SKU.
BUG=chrome-os-partner:55466
TEST=run RMT test, pass
Change-Id: Ie7aa79586665f6d3a7edd854a9eef07e6a1b2ab8
Signed-off-by: Andrey Petrov <andrey.petrov@intel.com>
Reviewed-on: https://review.coreboot.org/16320
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
|
|
Update FSP Header files to provide UPD for periodic training
disable. This is for the SIC 1.1.3/150_11 FSP release.
BUG=chrome-os-partner:54100
BRANCH=none
TEST=built coreboot image with new headers for reef
Change-Id: I2ba11aa3d2d664c1d34e39c4c8144fb1c4f2149a
Signed-off-by: Brandon Breitenstein <brandon.breitenstein@intel.com>
Reviewed-on: https://review.coreboot.org/16352
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
|
|
Expose get_microcode_info in cpu initialization. Microcode
revision is retrieved and stored into log file at verstage.
BUG=chrome-os-partner:56544
BRANCH=None
TEST=Built coreboot image and validate log file
Change-Id: I1e792e70f1318df64b4b85a319700013f3757952
Signed-off-by: John Zhao <john.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/16311
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Currently boards based on fsp_broadwell_de fail to compile if the config
switch CONFIG_DEBUG_SPI_FLASH is selected. The error is caused by the
usage of const for the address pointer in the functions writeb_, writew_
and writel_. The reason why it stayed hidden for so long is the fact that
the switch is used with the preprocessor and nobody really selects it
until there is a bug one want to find in this area.
This patch fixes the parameter type definition which solves the error.
In addition the config switch is not used on preprocessor level anymore
but instead on compiler level. This ensures that at least the code
syntax is checked on build time even if the config option is not
selected. Also prefix the messages with "SPI:" to make them more
meaningful in a full log.
Change-Id: I3514b0d4c08bf5a4740f2632641e09af1b3aaf3a
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/16347
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Add Kabylake specific Graphics IDs in report_platform.c and igd.c.
BUG=none
BRANCH=none
TEST=Built and boot kunimitsu
Change-Id: I3b810d0ff51eb51d396b783e282779aefb2dcb8c
Signed-off-by: Barnali Sarkar <barnali.sarkar@intel.com>
Reviewed-on: https://review.coreboot.org/16329
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
In order to provide time for the S0 rails to discharge one needs
to be able to set the SLP_S3_L assertion width. The hardware default
is 60 microcseconds which is not slow enough on most boards. Therefore
provide a devicetree option for the mainboard to set accordingly
for its needs. An unset value in devicetree results in a conservative
2 second SLP_S3_L duration.
BUG=chrome-os-partner:56581
Change-Id: I6c6df2f7a181746708ab7897249ae82109c55f50
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/16326
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Andrey Petrov <andrey.petrov@intel.com>
|
|
Add new option to set up Cache-As-RAM by using CQOS, Cache Quality of
Service. CQOS allows setting ways of cache in no-fill mode, while keeping
other ways in regular evicting mode. This effectively allows using CAR
and cache simultaneously.
BUG=chrome-os-partner:51959
TEST=switch from NEM to CQOS and back, boot
Change-Id: Ic7f9899918f94a5788b02a4fbd2f5d5ba9aaf91d
Signed-off-by: Andrey Petrov <andrey.petrov@intel.com>
Reviewed-on: https://review.coreboot.org/15455
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Update link addresses for romstage and verstage. Also update FSP-M relocation
address.
BUG=chrome-os-partner:51959
Change-Id: Ia51a341f05b33151ea5fda9f8620408b5a15bc19
Signed-off-by: Andrey Petrov <andrey.petrov@intel.com>
Reviewed-on: https://review.coreboot.org/15454
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Since whole L2 (1MiB) is not used, it is possible to shrink CAR size
to 768 KiB. Since 768 KiB is not power of two, 2 MTRRs are used to
set it up. This is a part of CQOS enabling.
BUG=chrome-os-partner:51959
Change-Id: I56326a1790df202a0e428e092dd90286c58763c5
Signed-off-by: Andrey Petrov <andrey.petrov@intel.com>
Reviewed-on: https://review.coreboot.org/15453
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Change-Id: I89bc8b26f2dba4770aea14b8bbc7e657355e8c59
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/16325
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Add in the base for ELOG for APL. Some PM events still need to be
added but the basic events are logged here. This enables the
basic functionality of ELOG for Apollolake.
BUG=chrome-os-partner:55473
BRANCH=none
TEST=Verified image boots on Amenia
Change-Id: I8682293e5a55b3efb5fdd9f1be1f3e4bf8d0757c
Signed-off-by: Brandon Breitenstein <brandon.breitenstein@intel.com>
Reviewed-on: https://review.coreboot.org/15937
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
|
|
Call power management utility function clear_wake_sts
from southbridge_smi_sleep before going to sleep.
This is needed to clear the wake status bits in ACPI
registers GPE0.
BUG=chrome-os-partner:55583
BRANCH=None
TEST=Verified that system goes to sleep on lidclose and
powerd_dbus_suspend command issued from built-in
keyboard.
Change-Id: I204a59f8a19137d6a192ea2d89939eefcd5d41ce
Signed-off-by: Shaunak Saha <shaunak.saha@intel.com>
Reviewed-on: https://review.coreboot.org/16299
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This patch adds a power management utility function to
clear wake status bits in ACPI GPE0 registers. We need
to call this function before going to sleep from
common smi handler function.
BUG=chrome-os-partner:55583
BRANCH=None
TEST=Verified that system goes to sleep on lidclose and
powerd_dbus_suspend command issued from built-in
keyboard.
Change-Id: Icd095d377c82f2e154f2e2db773f737aa49cda64
Signed-off-by: Shaunak Saha <shaunak.saha@intel.com>
Reviewed-on: https://review.coreboot.org/16298
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
When UART_DEBUG is enabled bootblock size grows more than the current
32K. Bump this up to 48K.
Change-Id: I580137dfdc9b4ad226c866f2b23b159bd820c62c
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/16317
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
The chromium tree is currently using a different config for
Chrome OS than what is being built in coreboot.org. Align those
settings to reflect how skylake Chrome OS boards are actually
shipped to provide proper parity between coreboot.org and chromium.
Change-Id: I7ab9c1dfa8c6be03ac2125fb06cb7022f3befa97
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/16313
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Implement PS0 and PS3 methods to support eMMC power gate
in S0ix suspend and resume.
BUG=chrome-os-partner:53876
TEST=Suspend and Resume using 'echo freeze > /sys/power/state'.
System should resume from S0ix.
Change-Id: Ia974e9ed67ee520d16f6d6a60294bc62a120fd76
Signed-off-by: Vaibhav Shankar <vaibhav.shankar@intel.com>
Reviewed-on: https://review.coreboot.org/16233
Tested-by: build bot (Jenkins)
Reviewed-by: Venkateswarlu V Vinjamuri <venkateswarlu.v.vinjamuri@intel.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Update the config variable that gets set to use DMIC 2 channel blob for
intel/apollolake platforms. This flag is set in mainboard.
Change-Id: Ic6deb9f08d345cc45351d61a7597bc7075ee20f9
Signed-off-by: Saurabh Satija <saurabh.satija@intel.com>
Reviewed-on: https://review.coreboot.org/16251
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Calling halt in poweroff when in SMM prevents SLP_SMI to be triggered
preventing the system from entering sleep state. Fix this by calling
halt only if ENV_SMM is not true.
BUG=chrome-os-partner:56395
Change-Id: I3addc1ea065346fbc5dbec9d1ad49bbd0ae05696
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/16259
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Calling halt in poweroff when in SMM prevents SLP_SMI to be triggered
preventing the system from entering sleep state. Fix this by calling
halt only if ENV_SMM is not true.
BUG=chrome-os-partner:56395
BRANCH=None
TEST=Verified lidclose behavior on reef.
Change-Id: If116c8f4e867543abdc2ff235457c167b5073767
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/16257
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
sts_index is calculated incorrectly because of wrong use of
parenthesis. This lead to wrong bit being checked for EC_SMI_GPI on reef
and lidclose event was missed.
BUG=chrome-os-partner:56395
BRANCH=None
TEST=Verified that lidclose event is seen and handled by SMM in
coreboot on reef.
Change-Id: I56be4aaf30e2d6712fc597b941206ca59ffaa915
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/16256
Tested-by: build bot (Jenkins)
Reviewed-by: Shaunak Saha <shaunak.saha@intel.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Read FSP produced memory HOB and use it to populate DIMM info.
DIMM 'part_num' info is stored statically based on memory/SKU id.
BUG=chrome-os-partner:55505
TEST='dmidecode -t 17' and 'mosys -k memory spd print all'
Change-Id: Ifcbb3329fd4414bba90eb584e065b1cb7f120e73
Signed-off-by: Ravi Sarawadi <ravishankar.sarawadi@intel.com>
Reviewed-on: https://review.coreboot.org/16246
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
If the boot device is SPI flash use the common one in the
early stages. While tweaking the config don't auto select
SPI_FLASH as that is handled automatically by the rest of the
build system.
BUG=chrome-os-partner:56151
Change-Id: Ifd51a80fd008c336233d6e460c354190fcc0ef22
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/16202
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
If the boot device is SPI flash use the common one in the
early stages. While tweaking the config don't auto select
SPI_FLASH as that is handled automatically by the rest of the
build system.
BUG=chrome-os-partner:56151
Change-Id: If5e3d06008d5529dd6d7c05d374a81ba172d58fd
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/16201
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Using malloc() in SPI code is unnecessary as there's only
one SPI device that the SoC support code handles: boot
device. Therefore, use CAR to for the storage to work around
the current limiations of the SPI API which expects one to
return pointers to objects that are writable. Additionally,
include the SPI support code as well as its dependencies in
all the stages.
BUG=chrome-os-partner:56151
Change-Id: I0192ab59f3555deaf6a6878cc31c059c5c2b7d3f
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/16196
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Lee Leahy <leroy.p.leahy@intel.com>
|
|
Using malloc() in SPI code is unnecessary as there's only
one SPI device that the SoC support code handles: boot
device. Therefore, use CAR to for the storage to work around
the current limiations of the SPI API which expects one to
return pointers to objects that are writable.
BUG=chrome-os-partner:56151
Change-Id: If4f5484e27d68b2dd1b17a281cf0b760086850a7
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/16195
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Indicate to the build system that a platform provides support
for a writable boot device. The following will provide the
necessary support:
COMMON_CBFS_SPI_WRAPPER users
soc/intel/apollolake
soc/intel/baytrail
soc/intel/braswell
soc/intel/broadwell
soc/intel/skylake
The SPI_FLASH option is auto-selected if the platform provides
write supoprt for the boot device and SPI flash is the boot
device.
Other platforms may provide similar support, but they do that
in a device specific manner such as selecting SPI_FLASH
explicitly. This provides clearance against build failures
where chipsets don't provide SPI API implementations even
though the platform may use a SPI flash to boot.
BUG=chrome-os-partner:56151
Change-Id: If78160f231c8312a313f9b9753607d044345d274
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/16211
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Make the indication of the boot device being memory mapped
separate from SPI. However, retain the same defaults that
previously existed.
BUG=chrome-os-partner:56151
Change-Id: I06f138078c47a1e4b4b3edbdbf662f171e11c9d4
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/16228
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
In SMM, gpio configuration could be done to avoid leakage. ITSS
configuration is not required when entering sleep. Thus, bail out early
from itss configuration if in SMM.
BUG=chrome-os-partner:56281
Change-Id: I4d8be0513aa202f001f980bb91986b50b8ed2a5b
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/16242
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
DCACHE_RAM_SIZE_TOTAL is set to 0x40000 and is being used to
set up CAR. Whereas DCACHE_RAM_SIZE which is set to 0x10000
is used to calculate the _car_region_end in car.ld. If the FSP CAR
requirement is greater than or even close to DCACHE_RAM_SIZE then,
the CAR region for FSP will be determined to be below the overall
CAR region boundary i.e, out of CAR memory range.
This is working with FSP 1.1 because we provide the FspCarSize
and FspCarBase explicitly in a UPD. Hence, FSP is still able to
use the upper region of CAR memory for its purpose.
However, it will be a problem in case of FSP2.0 where FSP usable CAR
is calculated using _car_region_end.
So, Remove the the use of DCACHE_RAM_SIZE_TOTAL and set
DCACHE_RAM_SIZE to correct value i.e, 0x40000(256KB)
Change-Id: Ie2cb8bb0705a37edb3414850d7659f8a3dd6958b
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/16236
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins)
|
|
There is a lot of code that is being referred to in bootblock but
resides under skylake/romstage folder. Hence move this code
into skylake/bootblock, and update the relevant header files
and Makefiles.
TEST=Build and Boot kunimitsu.
Change-Id: If94e16fe54ccb7ced9c6b480a661609bdd2dfa41
Signed-off-by: Naresh G Solanki <naresh.solanki@intel.com>
Reviewed-on: https://review.coreboot.org/16225
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Prepare Skylake for FSP2.0 support.
We do not use FSP-T in FSP2.0 driver, hence guard the
FspTempRamInit call under a switch.
In addition to the current early PCH configuration
program few more register, so all in all we do the following,
* Program and enable ACPI Base.
* Program and enable PWRM Base.
* Program TCO Base.
* Program Interrupt configuration registers.
* Program LPC IO decode range.
* Program SMBUS Base address and enable it.
* Enable upper 128 bytes of CMOS.
And split the above programming into into smaller functions.
Also, as part of bootblock_pch_early_init we enable decoding
for HPET range. This is needed for FspMemoryInit to store and
retrieve a global data pointer.
And also move P2SB related definitions to a new header file.
TEST=Build and boot Kunimitsu
Change-Id: Ia201e03b745836ebb43b8d7cfc77550105c71d16
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Signed-off-by: Barnali Sarkar <barnali.sarkar@intel.com>
Reviewed-on: https://review.coreboot.org/16113
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
pmc_gpe_route_to_gpio returns -1 on error. However, the value was being
stored in unsigned int and compared against -1. Fix this by using local
variable ret.
Change-Id: I5ec824949d4ee0fbdbb2ffdc9fc9d4762455b27b
Reported-by: Coverity ID 1357443, 1357442, 1357441
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/16218
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Program MCHBAR, DMIBAR, EPBAR, EDRAMBAR and GDXCBAR.
Also program the PAM registers. The system agent was being
programmed in romstage during pre-console initialization, after
moving to C_ENVIRONMENT bootblock this was missing, restoring
the same.
TEST=Build and Boot Kunimitsu
Change-Id: Iaf310cfb83e58eb8d5affb481dfc343f5d45961b
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/16224
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
This reverts commit a83bbf58541cf41ea7a97dedbc8c02dffa59e86d.
This was submitted out of order.
Change-Id: Ic5a28faf94c1f1901a72e46343722eb4224c5086
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/16226
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
The SPI host controller for the SPI boot device doesn't allow
normal probing because it uses the hardware sequencer all
the time. Therefore, it's pointless to include unnecessary
SPI flash drivers.
BUG=chrome-os-partner:56151
Change-Id: Ifcc6492b4bccf7d01b121d908976c9087d12deb0
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/16189
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
The SPI host controller for the SPI boot device doesn't allow
normal probing because it uses the hardware sequencer all
the time. Therefore, it's pointless to include unnecessary
SPI flash drivers.
BUG=chrome-os-partner:56151
Change-Id: I04551fdb0b207c7ec2f1f171cff62ed7334a5ad5
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/16188
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Make the indication of the boot device being memory mapped
separate from SPI. However, retain the same defaults that
previously existed.
BUG=chrome-os-partner:56151
Change-Id: Ibdd7c8754f9bf560a878136b1f55238e2c2549d3
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/16193
Reviewed-by: Andrey Petrov <andrey.petrov@intel.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Having an assignment in assert does not make sense. This seems like it
was intended to check if chip is always same as segments->chip.
Change-Id: I297d9e76a0404a1f510d43f8b9c39e96b557689f
Reported-by: Coverity ID 1357439
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/16219
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Lee Leahy <leroy.p.leahy@intel.com>
|
|
The function name "pmc_tco_regs" is changed to "smbus_tco_regs"
since TCO offsets belongs to SMBUS PCI device.
BUG=none
BRANCH=none
TEST=Built and booted kunimitsu
Change-Id: I4ac26df81a8221329f2b45053dd5243cd02f8ad7
Signed-off-by: Barnali Sarkar <barnali.sarkar@intel.com>
Reviewed-on: https://review.coreboot.org/16155
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
FSP unconditionally locks parts of the NVRAM in the RTC.
This change will enable coreboot to update the locking policy
and be able to unlock the region
BUG=chrome-os-partner:55944
TEST=Check 'crossystem dev_boot_usb=1'
Change-Id: I70fd2bafa6ff9eb9cdf284b9780e4b90dee0f4ce
Signed-off-by: Ravi Sarawadi <ravishankar.sarawadi@intel.com>
Reviewed-on: https://review.coreboot.org/16144
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Giri P Mudusuru <giri.p.mudusuru@intel.com>
|
|
This patch enables serial debug functionality for ASL code based on
UART type(legacy/LPSS).
From Skylake onwards all Intel platform uses LPSS based UART for serial
console hence provide option to redirect ASL log over LPSS UART.
Example:
Name (OBJ, 0x12)
APRT (OBJ)
APRT ("CORE BOOT")
Output:
0x12
CORE BOOT
BUG=none
BRANCH=none
TEST=Built and boot kunimitsu to ensure to be able to get ASL console log.
Change-Id: I18c65654b8eb1ac27af1f283d413376fd79d47db
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/16070
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
When booting Linux as a coreboot payload, serial access does not work
properly. This is because the setup code erroneously sets IRQ3 and
IRQ4 to level. The UART on Broadwell is 8250/16550 compatible, thus
ISA and edge-triggered.
This change is not necessary on the non-FSP version of Broadwell support.
The non-FSP version does not set these IRQ overrides.
Fix verified booting Linux 4.6.0-rc2 on Intel Camelback Mountain CRB,
using Intel FSP 1.0.
Change-Id: I17b466676e7f4891c3e75ce6208e1580c9eaf742
Signed-off-by: Kevin Paul Herbert <kevin@trippers.org>
Reviewed-on: https://review.coreboot.org/16065
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Switch from passing FSP the serial port address to passing FSP the
serial port output routine. This enables coreboot to use any UART in
the system and also log the FSP output.
TEST=Build and run on Galileo Gen2
Change-Id: I67d820ea0360a3188480455dd2595be7f2debd5c
Signed-off-by: Lee Leahy <leroy.p.leahy@intel.com>
Reviewed-on: https://review.coreboot.org/16105
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
The variable MAINBOARD_DIR already has the quotes stripped off.
Change-Id: Ib434ce92bdbc49180fb3f713b26d65ba4cf8c441
Signed-off-by: Martin Roth <martinroth@chromium.org>
Reviewed-on: https://review.coreboot.org/16117
Tested-by: build bot (Jenkins)
Reviewed-by: Lee Leahy <leroy.p.leahy@intel.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
GPIOs which trigger SMIs set the GPIO_SMI_STS status bits in SMI_STS
register. This patch also sets the SMI_EN bit in enable register for
each community based on GPIOROUTSMI bit in gpio pad. When SMI on a
gpio happens status needs to be gathered on gpio number which is done
by reading the GPI_SMI_STS and GPI_SMI_EN registers.
BUG=chrome-os-partner:54977
TEST=When system is in firmware mode executing the command
lidclose from ec console shuts down the system.
Change-Id: Id89a526106d1989c2bd3416ab81913e6cf743d17
Signed-off-by: Shaunak Saha <shaunak.saha@intel.com>
Reviewed-on: https://review.coreboot.org/15833
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
|
|
The gsmi_exec() expects the parameter to be a pointer
to the 32-bit register storage of the SMI save state.
The previous code was passing a pointer with the value
obtained from the saved-state -- not a pointer to the
storage of the register value. This bug causes gsmi
to not log events because it's interrogating the
parameter buffer itself as if it were a pointer.
BUG=chrome-os-partner:55932
Change-Id: I37981424f1414edad1456b31cad1b99020d57db6
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/16087
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Since RTC is now a Kconfig ensure RTC is selected on the
x86 chipsets which are in Chrome OS devices. This allows
the eventlog to have proper timestamps instead of all
zeros.
BUG=chrome-os-partner:55993
Change-Id: I24ae7d9b3bf43a5791d4dc04aae018ce17fda72b
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/16086
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
List of changes done here in this patch
1. Remove CARD definition from EMMC and SD Card Controller in scs.asl
since _RMV method does not get evaluated while setting up removable
attribute in sysfs in kernel.
"cat /sys/block/mmcblk1/removable" this command always returns 0.
This CARD Device includes _ADR which follows SDIO Bus format. But,
SD/EMMC sits on PCI Bus.
Hence this CARD Device specific _ADR code is also not needed.
2. Remove Base Address for ACPI debug output memory buffer in
systemagent.asl as it is not getting used throughout the code.
BUG=none
BRANCH=none
TEST=Build and boot kunimitsu
Change-Id: I29effaffdafcc21e26445ec3c54aedecdbc50274
Signed-off-by: Barnali Sarkar <barnali.sarkar@intel.com>
Reviewed-on: https://review.coreboot.org/16068
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
|
|
Program PIRQ Routing with correct values, as done by FSP, and also in
'soc/intel/skylake/romstage/pch.c' file. If not done, these values get
overridden by "0" during PxRC -> PIRQ programming in ramstage, in
'soc/intel/skylake/lpc.c' file pch_pirq_init()function.
BUG=none
BRANCH=none
TEST=Build and boot kunimitsu
Change-Id: Ibeb9a64824a71c253e45d6a1c6088abd737cf046
Signed-off-by: Barnali Sarkar <barnali.sarkar@intel.com>
Reviewed-on: https://review.coreboot.org/16044
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
|
|
Here is the list of items of code cleanup
1. Define TCO registers in smbus.h and not in pmc.h (as per EDS).
2. Include smbus.h wherever these TCO register defines were used.
3. Remove duplication of define in gpio_defs.h.
4. Remove unnecessary console.h include from memmap.h as no prints done.
5. Remove unnecessary comment from pch.c.
BUG=none
BRANCH=none
TEST=Built and boot kunimitsu.
Change-Id: Ibe6d2537ddde3c1c7f8ea5ada1bfaa9be79c0e3b
Signed-off-by: Barnali Sarkar <barnali.sarkar@intel.com>
Reviewed-on: https://review.coreboot.org/16027
Tested-by: build bot (Jenkins)
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
|
|
Adding kabylake device ids for chip inits.
Skylake and Kabylak do not differ much, the intention
is to support both SoCs in the same code base.
Change-Id: I9ff4c6ca08fe681798001ce81cca2c085ce32325
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/16049
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Add missing breaks in reg_access.c.
TEST=Build and run on Galileo Gen2
Found-by: Converity Scan #1361261
Change-Id: I8be57f0758e5918a605e20ab9002747e0cc958e0
Signed-off-by: Lee Leahy <leroy.p.leahy@intel.com>
Reviewed-on: https://review.coreboot.org/16069
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
|
|
Add the bootblock_c_entry routine to make it more explicit where the
code transitions from assembler to C.
TEST=Build and run on Galileo Gen2
Change-Id: Ib5f580c30b58d3c82fedddf63c368e617d401515
Signed-off-by: Lee Leahy <leroy.p.leahy@intel.com>
Reviewed-on: https://review.coreboot.org/16064
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Change the debug output levels for quark:
* Remove excess debug output
* Change BIOS_DEBUG to BIOS_SPEW - exception in report_platform.c
TEST=Build and run on Galileo Gen2
Change-Id: I37d7ed21a7fc4c92efeb5b71dd01922d7d4b9192
Signed-off-by: Lee Leahy <leroy.p.leahy@intel.com>
Reviewed-on: https://review.coreboot.org/16006
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Disable FSP output when CONFIG_DEFAULT_CONSOLE_LOGLEVEL is not set to 8
(BIOS_SPEW). Use the console log level to choose between the serial
port address and NULL and pass it to FSP for the serial port address.
TEST=Build and run on Galileo Gen2.
Change-Id: I5498aad218524c211082d85d0ae9aacaf08a80f6
Signed-off-by: Lee Leahy <leroy.p.leahy@intel.com>
Reviewed-on: https://review.coreboot.org/16005
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Add the pieces necessary to successfully build and run romstage using
the FSP 2.0 build. Because romstage is using postcar, add the postcar
pieces so that romstage can attempt to load postcar.
TEST=Build and run on Galileo Gen2
Change-Id: I66b3437e3c7840223535f6ab643599c9e4924968
Signed-off-by: Lee Leahy <leroy.p.leahy@intel.com>
Reviewed-on: https://review.coreboot.org/15866
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Add the pieces necessary to successfully build and run bootblock using
the FSP 2.0 build.
TEST=Build and run bootblock on Galileo Gen2
Change-Id: I2377f0b0147196f100396b8cd7eaca8f92d6932f
Signed-off-by: Lee Leahy <leroy.p.leahy@intel.com>
Reviewed-on: https://review.coreboot.org/15865
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Wake status is calculated from the four pairs of gpe0 in
cbmem CBMEM_ID_POWER_STATE which is filled very early
in romstage and depends on the routing information in
PMC GPE_CFG register. Coreboot sets the proper value
of routing based on devicetree from pmc_init. But when
system goes to S3 on waking up PMC is writing default
values again in GPE_CFG which results in returning
wrong wake status in _SWS. This patch corrects that
behaviour by correcting the gpe0 pairs in cbmem after
PMC sets the routing table in resume path.
BUG=chrome-os-partner:54876
TEST=On resume through powerbtn, lidopen, keyboard press, etc.
we are getting proper wake status.
Change-Id: I5942d5c20d8c6aef73468dc611190bb7c49c7c7a
Signed-off-by: Shaunak Saha <shaunak.saha@intel.com>
Reviewed-on: https://review.coreboot.org/16040
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Brandon Breitenstein <brandon.breitenstein@intel.com>
|
|
For the gpio based irq to work, the ownership of the pad
should be changed to GPIO_DRIVER.
Provide an option in the gpio defs to configure the PAD onwership.
BUG=chrome-os-partner:54371
TEST=none
Change-Id: I26d242d25d2034049340adf526045308fcdebbc0
Signed-off-by: Jagadish Krishnamoorthy <jagadish.krishnamoorthy@intel.com>
Reviewed-on: https://review.coreboot.org/15871
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
|
|
This corrects the address of the I2C5 Device. The I2C
Controller #5 is on PCI Bus 0: Device 25: Function 1. The ACPI
Address Encoding Logic is - High word = Device #.
Low word = Function #.
So, I2C5 (_ADR) = 0x0019 0001.
BUG=none
BRANCH=none
TEST=Build and boot kunimitsu
Change-Id: I4719a843260ef58cc2307e909e9ccbffea519177
Signed-off-by: Barnali Sarkar <barnali.sarkar@intel.com>
Reviewed-on: https://review.coreboot.org/16048
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Add support to access CR0 and CR4.
TEST=Build and run on Galileo Gen2.
Change-Id: I8084b7824ae9fbcd55e11a7b5eec142591a7e279
Signed-off-by: Lee Leahy <leroy.p.leahy@intel.com>
Reviewed-on: https://review.coreboot.org/16004
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Add the FSP 2.0 header files for Quark. These files were run through
the drivers/intel/fsp2_0/header_util to convert the data types so that
they are compatible with the coreboot build system.
TEST=Build and run on Galileo Gen2.
Change-Id: I15548888215cc811fa753d30b65e3a19e3f8ff8d
Signed-off-by: Lee Leahy <leroy.p.leahy@intel.com>
Reviewed-on: https://review.coreboot.org/15863
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Split the original contents of romstage.c into car.c, romstage.c and
fsp1_1.c.
TEST=Build and run on Galileo Gen2
Change-Id: I6392d7382e383ea2087afa6bf45b1f087ba78d79
Signed-off-by: Lee Leahy <leroy.p.leahy@intel.com>
Reviewed-on: https://review.coreboot.org/15862
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Initialize the MTRRs for use by bootblock and romstage.
Display the MTRRs.
TEST=Build and run on Galileo Gen2.
Change-Id: Ib1d422c738820163f54771c65034ae77301237ec
Signed-off-by: Lee Leahy <leroy.p.leahy@intel.com>
Reviewed-on: https://review.coreboot.org/15861
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Include assert.h to use coreboot's ASSERT macro.
Replace the use of UINT32 data type with uint32_t.
Replace the use of UINT8 data type with uint8_t.
TEST=Build and run on Galileo Gen2
Change-Id: I0bb7e43ea570f7b20355c5d05675ebf593942e83
Signed-off-by: Lee Leahy <leroy.p.leahy@intel.com>
Reviewed-on: https://review.coreboot.org/15858
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Create DMAR table for Broadwell-DE SoC.
TEST=Booted MC BDX1 into lubuntu15, dumped ACPI tables with acpidump and
disassembled DMAR table using iasl. The table contents are as
expected and the kernel loads DMAR table without errors.
Change-Id: I7933ba4f5f0539a50f2ab9a5571e502c84873ec6
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/15913
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Relocate ramstage into CBMEM.
TEST=Build and run on Galileo Gen2
Change-Id: I38861f2af4b7b976c7ebb7226d81242f950981e3
Signed-off-by: Lee Leahy <leroy.p.leahy@intel.com>
Reviewed-on: https://review.coreboot.org/15994
Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Other SOC platforms need to handle the FspNotify calls in the same way
as Apollo Lake. Migrate the FspNotify calls into the FSP 2.0 driver.
Provide a platform callback to handle anything else that needs to be
done after the FspNotify call.
Display the MTRRs before the first call to fsp_notify.
TEST=Build and run on Galileo Gen2
Change-Id: I1ff327d77516d4ea212740c16c2514c2908758a2
Signed-off-by: Lee Leahy <leroy.p.leahy@intel.com>
Reviewed-on: https://review.coreboot.org/15855
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Move all FSP error handling into the FSP 2.0 driver. This removes the
need to implement error handling within the SOC code.
TEST=Build and run on Galileo Gen2
Change-Id: I4d548b4c90d369d3857c24f50f93e7db7e9d3028
Signed-off-by: Lee Leahy <leroy.p.leahy@intel.com>
Reviewed-on: https://review.coreboot.org/15853
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
per hw team's check and info from EDS, this pin needs to be pu 20K.
Otherwise SoC may not notice interrupt request from
EC over LPC because SERIRQ line is floating.
BUG=chrome-os-partner:55586
BRANCH=none
TEST=boot ok and Quanta factory verified the keyboard issue is gone
Signed-off-by: Kane Chen <kane.chen@intel.com>
Change-Id: I5b0213514ce152d4e2cecdda8786925495a0f24a
Reviewed-on: https://review.coreboot.org/15951
Tested-by: build bot (Jenkins)
Reviewed-by: Freddy Paul <freddy.paul@intel.com>
Reviewed-by: Andrey Petrov <andrey.petrov@intel.com>
|
|
IO Standby State (IOSSTATE): The I/O Standby State defines
which state the pad should be parked in when the I/O is in a
standby state. Iosstate set to 15 means IO-Standby is ignored
for this pin (same as functional mode), So that pin keeps on
functioning in S3/S0iX.
Change-Id: Ie51ff86a2ea63fa6535407fcc2df7a137ee43e8b
Signed-off-by: Venkateswarlu Vinjamuri <venkateswarlu.v.vinjamuri@intel.com>
Signed-off-by: Shankar, Vaibhav <vaibhav.shankar@intel.com>
Reviewed-on: https://review.coreboot.org/15776
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Upper CMOS bank is used to store the boot count. It is important to
enable it as soon as possible in bootblock.
BUG=chrome-os-partner:55473
Change-Id: I7c4f49c337c2e24a93c1e71466e2f66db04be562
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/15998
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
1. skylake does not support UART over I/O. So, NO_UART_ON_SUPERIO needs
to be selected by default.
2. Move BOOTBLOCK_CONSOLE under UART_DEBUG.
3. Include bootblock/uart.c only if UART_DEBUG is selected.
Change-Id: I4e996bea2a25b3b1dfb9625d97985a9d3473561b
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/16025
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
|
|
Without this patch, eDP output is non-functional pre-graphics driver
regardless of payload (SeaBIOS, Tianocore) or video init method
(VBIOS, GOP driver) and once the standard Windows Intel HD graphics
driver is loaded.
Test: Boot Windows on peppy and auron_paine, install Intel HD
Graphics driver, observe functional eDP output with full video
acceleration.
Debugging method: adjust location of call to run VBIOS within
coreboot, observed that eDP output functional if the VBIOS is run
before the power optimizer lines, broken if run afterwards.
Change-Id: I6d8252e3de396887c84533e355f41693b9ea7514
Signed-off-by: Prabal Saha <coolstarorganization@gmail.com>
Reviewed-on: https://review.coreboot.org/15261
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Select HAVE_HARD_RESET in the KCONFIG file to enable use of the
hard_reset routine.
TEST=Build and run on Galileo Gen2
Change-Id: Ib11a80b64cf1c55aec24f2576d197da9017b9751
Signed-off-by: Lee Leahy <leroy.p.leahy@intel.com>
Reviewed-on: https://review.coreboot.org/15992
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Fix build error caused by macro substitution in the function definition
when the Kconfig value HAVE_HARD_RESET is not selected.
src/soc/intel/common/reset.c:36:21: error: macro "hard_reset" passed 1 arguments, but takes just 0
void hard_reset(void)
^
src/soc/intel/common/reset.c:37:1: error: expected '=', ',', ';', 'asm' or '__attribute__' before '{' token
{
^
make: *** [build/bootblock/soc/intel/common/reset.o] Error 1
TEST=Build and run on Galileo Gen2
Change-Id: I793570e62a0e46cca86cc540c243e363896ceac7
Signed-off-by: Lee Leahy <leroy.p.leahy@intel.com>
Reviewed-on: https://review.coreboot.org/15988
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
These non-ascii & unprintable characters aren't needed.
Change-Id: I129f729f66d6a692de729d76971f7deb7a19c254
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/15977
Tested-by: build bot (Jenkins)
Reviewed-by: Omar Pakker
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Change-Id: I7930d5cded290f2605d0c92a9c465a3f0c1291a2
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/15974
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Update Makefile.inc to allow MTRR display during bootblock and postcar.
TEST=Build and run on Galileo Gen2
Change-Id: If12896df46b9edfc9fff3fab3a12d2dae23517a3
Signed-off-by: Lee Leahy <leroy.p.leahy@intel.com>
Reviewed-on: https://review.coreboot.org/15990
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Change routine name from car_state_entry to car_stage_entry.
TEST=Build and run on Galileo Gen2
Change-Id: Ifd11db3fa711f2fe52ade1c6cde94f9be1f3a652
Signed-off-by: Lee Leahy <leroy.p.leahy@intel.com>
Reviewed-on: https://review.coreboot.org/15857
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Change-Id: I7f0d3400126d593bad8e78f95e6b9a378463b4ce
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/15963
Tested-by: build bot (Jenkins)
Reviewed-by: Omar Pakker
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
(pci_read_config32(...) > 14) & 0x3 looks rather unusual (and prevents
"case 3" below from ever happening)
Change-Id: Id90655c39ff53da9569441278bbf73497d643480
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Found-by: Coverity Scan #1293139
Reviewed-on: https://review.coreboot.org/15965
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Testing for "devfn < 0" on an unsigned doesn't work, and i2c_bus_to_devfn
returns an int (with -1 for "error"), so use int for devfn.
Change-Id: I7d1cdb6af4140f7dc322141c0c018d8418627434
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Found-by: Coverity Scan #1357450, #1357449
Reviewed-on: https://review.coreboot.org/15964
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
This removes the newlines from all files found by the new
int-015-final-newlines script.
Change-Id: I65b6d5b403fe3fa30b7ac11958cc0f9880704ed7
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/15975
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
