Age | Commit message (Collapse) | Author |
|
add an unused param so that mca_configure can be called
by mp_run_on_all_cpus to run it on all cores.
Change-Id: I2395ee7fbedc829f040959b0021967f800693eeb
Signed-off-by: Pratik Prajapati <pratikkumar.v.prajapati@intel.com>
Reviewed-on: https://review.coreboot.org/26391
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
This patch cleans soc/intel/{apollolake/cannonlake/skylake} by moving
common soc code into common/block/p2sb.
BUG=b:78109109
BRANCH=none
TEST=Build and boot KBL/CNL/APL platform.
Change-Id: Ie9fd933d155b3fcd0d616b41cdf042cefe2c649a
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/26132
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
During Speaker playback, quad Channel I/V feedback data is
captured from SSP0 Rx. Out of these 4-channels, Stereo V-Sense data
needs to be given as echo ref stream.
So, adding stereo capture config to max98373_capture_formats.
BUG=b:110074225
TEST='Audio playback and Capture Stereo echo ref data'
Change-Id: I6fe619ece94d5011caffe37ef10b48f956938db9
Signed-off-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Reviewed-on: https://review.coreboot.org/27182
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
SoC users from IOTG team is looking forward for a solution to skip
coreboot AP initialization flow and make use of FSPS-UPD to
perform AP reset.
TEST=Assign use_fsp_mp_init=1 to ensure coreboot is not bringing APs
out of reset.
Change-Id: Ibc8cd411e802fb682436a933073922b2693ba994
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/26644
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
C1E is disabled by the kernel driver intel_idle at boot. This does not
address the S3 resume case, so we lose state and C1E is enabled after S3
resume.
Disable C1E for SKL and KBL. This gives a coherent state before
and after S3 resume.
TEST='iotools rdmsr cpu 0x1fc'. Returns the same value after boot and S3
resume with bit [1] set to zero (0x20005d).
Change-Id: I1343f343bfac9b787f13c15b812c0a201dcccb38
Signed-off-by: Cole Nelson <colex.nelson@intel.com>
Reviewed-on: https://review.coreboot.org/27125
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Use of device_t is deprecated.
Change-Id: I6adc0429ae9ecc8f726d6167a6458d9333dc515f
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/27036
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Shuffle words and drop the _DATA_FILE suffix.
Change-Id: I0b0d50ea729e5580c0bc7b43f250ff387ce59cfc
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/26898
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
This patch sets the ACPI FADT flag ACPI_FADT_LOW_POWER_S0
if S0ix is enabled for the platform.
BUG=b:79559085
TEST= Boot to OS and check the ACPI_FADT_LOW_PWR_IDLE_S0
flag is set in FACP table - FADT.Flags[21] bit.
Change-Id: I0b8a86118232a66e7466d5b8116eff6087b51210
Signed-off-by: Haridhar Kalvala <haridhar.kalvala@intel.com>
Signed-off-by: Rajneesh Bhardwaj <rajneesh.bhardwaj@intel.com>
Reviewed-on: https://review.coreboot.org/26940
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Naresh Solanki <naresh.solanki@intel.com>
|
|
pch lockdown functionality can be used by supported PCH.
Right now pch lockdown functionality is applied for SPT
(Skylake SOC) and CNP(Cannon Lake SOC) PCH.
BUG=b:78109109
BRANCH=none
TEST=Build and boot KBL and CNL platform.
Change-Id: I0b81bbc54f737cb4e7120f44bbe705039b45ccb3
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/25688
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
No need to provide an option to try disable this.
Also remove explicit ´select RELOCATABLE_MODULES'
lines from platform Kconfigs.
Change-Id: I5fb169f90331ce37b4113378405323ec856d6fee
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/26815
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
This patch cleans soc/intel/{apollolake/cannonlake/skylake} by moving
common soc code into common/block/i2c.
BUG=b:78109109
BRANCH=none
TEST=Build and boot KBL/CNL/APL platform.
Change-Id: I88f2f836eee4f80b79486dd8644d1bb3826c5af1
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/26056
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This patch cleans soc/intel/{apollolake/cannonlake/skylake} by moving
common soc code into common/block/gspi.
BUG=b:78109109
BRANCH=none
TEST=Build and boot KBL/CNL/APL platform.
Change-Id: I877c7c48af928ca1e0399ec794d9400bc52edfcb
Signed-off-by: Ravi Sarawadi <ravishankar.sarawadi@intel.com>
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/26048
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Adding common chip config structure which will be used to return data to
common code. When common code requires soc data, code used to fetch
entire soc config structure. With this change, common code will only get
the data/structure which is required by common code and not entire
config.
For now, adding i2c, gspi and lockdown configuration which will be used
by common code.
BUG=none
BRANCH=b:78109109
TEST=compile code for APL/SKL/CNL. Boot using SKL/APL/CNL and check
values are returned properly using common structure.
Change-Id: I7f1671e064782397d3ace066a08bf1333192b21a
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/26189
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Hannah Williams <hannah.williams@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch creates a glue layer between SOC and common block IPs in terms
of PCH. All common IP blocks now can be selected based on
SOC_INTEL_COMMON_PCH_BASE config option.
BUG=none
BRANCH=b:78109109
TEST=Build and boot Cannonlake RVP and EVE.
Change-Id: I4e1f009489f2d8338ae94b78d7e9eb3f88a85d99
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/26349
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This patch provides option for mainboard to skip coreboot MP
initialization if required based on use_fsp_mp_init.
Option for mainboard to skip coreboot MP initialization
* 0 = Make use of coreboot MP Init
* 1 = Make use of FSP MP Init
Default coreboot does MP initialization.
Change-Id: I8de24e662963f4600209ad1b110dc950ecfb3a27
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/26818
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
After FSP-S, a device on PCI function n will be function swapped
to function 0 if there is no device presnet on function 0.
It needs some modification for DT and causes mismatches between
software configuration and hardware schematic. This patch is
from d779605, which swaps the devfn of the first enabled device
in DT and function 0 resides in a PCI device.
BUG=b:80105785
BRANCH=None
TEST=Make sure the device is still enabled after coalescence with
device on bus 0 and w/o device on bus 0. Test with suspend
and resume and ensure it's consistent.
Change-Id: Ibbc5d6e979977011f5904c8bd4b2f1be16bd23dc
Signed-off-by: Gaggery Tsai <gaggery.tsai@intel.com>
Reviewed-on: https://review.coreboot.org/26479
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Change-Id: Ia024fb418f02d90c38b9a35ff819c607b9ac4965
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/26651
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Change-Id: Iee816628ac3c33633f5f45798562a4ce49493a65
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/26580
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Use of device_t has been abandoned in ramstage.
Change-Id: Idf00c029331aba30c8bfca71546cad62ff6bb0a7
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/26541
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Boards could choose a high ROM_SIZE that would result in an MTRR config
that conflicts with other resources. Thus, always use the filtered
CACHE_ROM_SIZE.
Change-Id: I66d36b84ce49c1cb98cb36a4731977baaedf3225
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/26575
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch select CONFIG_SOC_INTEL_COMMON_BLOCK_P2SB to include
common p2sb code block.
BUG=b:78109109
BRANCH=none
TEST=Build and boot EVE.
Change-Id: I3f6aa6398e409a05a35766fb7aeb3aa221dd3970
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/26165
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Max98373's NHLT capture configuration is used for IV feedback for
DSM algorithm.
Feedback is 4-channel data. Without this configuration below error
is seen in dmesg:
[ 315.784250] snd_soc_skl 0000:00:1f.3: Blob NULL for id 0 type 3 dirn 1
[ 315.784263] snd_soc_skl 0000:00:1f.3: PCM: ch 4, freq 48000, fmt 32
So, update nhlt configuration accordingly.
BUG=b:79362472
TEST=Audio playback works with IV feedback enabled
Change-Id: I75434a63fe030ed9bb963c6d300d833a8e7d2d66
Signed-off-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Reviewed-on: https://review.coreboot.org/26384
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: Iedb78e24a286a51830c85724af0179995ed553be
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/26434
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
This patch adds more parameters to bootblock_main_with_timestamp() to
give callers the opportunity to add additional timestamps that were
recorded in the platform-specific initialization phase.
Change-Id: Idf3a0fcf5aee88a33747afc69e055b95bd38750c
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/26339
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
To support generating USB devices in ACPI the platform needs to
know how to determine a device name for each USB port, and for
any root hubs that may be present.
Recent Intel platforms route all ports to an XHCI controller
through a root hub. This is supported by considering the root
hub to be USB port type 0, the USB 2.0 ports to be type 2, and
the USB 3.0 ports to be type 3.
This was tested with a Kaby Lake platform by adding entries to
the devicetree and checking the resulting SSDT.
Change-Id: I527a63bdc64f9243fe57487363ee6d5f60be84ca
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/26174
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Increase AP timeout limit for sgx_configure function. As per debug log
sgx_configure was not successful on all cores with given timeout value.
TEST=Ensures no timeout error in AP function execution.
Change-Id: Ia83f7a7eb6cd6c4808d55febfebe32724a633173
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/26286
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Caveh Jalali <caveh@google.com>
|
|
Because thermal table is not included the values of DPTF_TSR1_ACTIVE_AC
from internal nami/vayne thermal team. Add conditional compilation
in _ACx methods if DPTF_ENABLE_FAN_CONTROL is defined in the dptf.asl.
BUG=b:72974136
TEST=Match the result.
Change-Id: I4b593118ca460a59aa49786cb99df417d135112a
Signed-off-by: John Su <john_su@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/26210
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This patch ensures that user can pass a function with given argument
list to execute over APs.
BUG=b:74436746
BRANCH=none
TEST=Able to run functions over APs with argument.
Change-Id: I668b36752f6b21cb99cd1416c385d53e96117213
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/25725
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
The current PCH UART support for console is limited to UART2.
This change adds support for specifying UART0 or UART1 to be
used instead by changing CONFIG_UART_FOR_CONSOLE in the board
level Kconfig. The default is still 2.
This is tested with a board that uses UART0 for debug output.
Change-Id: I91323ed3298f9b2558764aa4b54173833c021a7b
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/26140
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
pci_bus_default_ops() is the default anyway.
Change-Id: I5306d3feea3fc583171d8c865abbe0864b6d9cc6
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/26055
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Skylake used the inner function, wrapping it in the same set of tests as
the common code does, but expressed differently.
Change-Id: Ifa6912255e7874a6e80301d49128adda6f624209
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/26037
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Currently the thermal event handler method TEVT is defined as an extern,
then defined again in platforms with thermal event handling. In newer
versions of IASL, this generates an error, as the method is defined in
two places. Simply removing the extern causes the call to it to fail on
platforms where it isn't actually defined, so add a preprocessor define
where it's implemented, and only call the method on those platforms.
Change-Id: I64dcd2918d14f75ad3c356b321250bfa9d92c8a5
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/25916
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Instead of writing out '__attribute__((weak))' use a shorter form.
Change-Id: If418a1d55052780077febd2d8f2089021f414b91
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/25767
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
|
|
Move inline function where they belong to. Fixes compilation
on non x86 platforms.
Change-Id: Ia05391c43b8d501bd68df5654bcfb587f8786f71
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/25720
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Because thermal table is not included the values of DPTF_TSR0_ACTIVE_AC5
and DPTF_TSR0_ACTIVE_AC6 from internal nami/vayne thermal team.
Add conditional compilation in _ACx methods if DPTF_ENABLE_FAN_CONTROL
is defined in the dptf.asl.
BUG=b:72974136
BRANCH=poppy
TEST=emerge-nami coreboot and booted on nami board.
Change-Id: I3e36ce94f714ff13f8ccee65992d7a9c7e0bb5b2
Signed-off-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/25614
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Also base the FSP/GOP related bail-out on the correct Kconfig option
to allow adding a VBT along with libgfxinit.
Most things should work, what doesn't is backlight control because
coreboot misses the settings (moved to FSP and need backporting).
Also, Kaby Lake is still unsupported.
TEST=Booted yet to be upstreamed Skylake-S port (Kontron/bSL6) both with
text and linear framebuffer mode and viewed a FILO menu.
Change-Id: I79fbfed7732cf02d054530ea7ec0d34de32836ba
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/20113
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
|
|
Change-Id: I639be58df358129c1f420cf8d1540edd408859a7
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/25572
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Apparently Intel had decided to use different clock speeds for
some of its IP blocks in some of its designs. The i2c designware driver
has already been moved into common code allowing for its own Kconfig
value. That currently leaves SPI (UART isn't using the clock currently).
Therefore, remove SOC_INTEL_COMMON_LPSS_CLOCK_MHZ and add
SOC_INTEL_COMMON_BLOCK_GSPI_CLOCK_MHZ to allow for the different clock
speeds present in the system for the various IP blocks.
BUG=b:75306520
Change-Id: I6cb8c2de0ff446b6006bc37645fca64f2b70bf17
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/25608
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Hannah Williams <hannah.williams@intel.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
If the SoC is VT-d capable, write an ACPI DMAR table. The entry for the
GFXVTBAR is only generated if the IGD is enabled.
Change-Id: I8176401dd19aee7ad09a8a145b7a3801fe5b2ae1
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/21588
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Youness Alaoui <snifikino@gmail.com>
|
|
We use the usual static addresses 0xfed90000/0xfed91000 for the GFX
IOMMU and the general IOMMU respectively. These addresses have to be
configured in MCHBAR registers (maybe, who knows, the blob is undocu-
mented), advertised to FSP and reserved from the OS.
The new devicetree option `ignore_vtd` allows to retain the old beha-
viour (do whatever pre-set UPD values suggest).
We also let FSP set up distinct BDFs for messages originating from the
I/O-APIC and the HPET.
Change-Id: I77f87c385736615c127143760bbd144f97986b37
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/21597
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Youness Alaoui <snifikino@gmail.com>
|
|
Add global/ACPI nvs variables required for IGD OpRegion.
Add functions necessary to save the ACPI OpRegion table
address in ASLB, and restore table address upon S3 resume.
Implementation modeled on existing Baytrail code.
Test: boot Windows 10 on google/chell with Tianocore payload and
GOP display init, observe display driver loaded and functional,
display not black screen when resuming from S3 suspend.
Change-Id: Icd6b514e531eec6e49dbb03eb765144f41c1e31b
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/25198
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
Get rid of custom opregion implementation and use drivers/intel/gma/opregion
implementation instead.
Test: boot Windows 10 on google/chell and google/edgar using Tianocore
payload with GOP init, observe Intel graphics driver loaded and functional.
Change-Id: I5f78e9030df12da5369d142dda5c59e576ebcef7
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/21703
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
me_progress_rom_values array provides detailed information maps to ME
HFSTS2 register value.
There is a chance that ME status value might be over the size of
me_progress_rom_values.
This commit adds a check before access the array.
BUG=b:77247550
Change-Id: I5de569c62b94b0595d3d3ea254f50e312e8c11a4
Signed-off-by: Kane Chen <kane.chen@intel.com>
Reviewed-on: https://review.coreboot.org/25425
Reviewed-by: Kevin Chiu <Kevin.Chiu@quantatw.com>
Reviewed-by: Shelley Chen <shchen@google.com>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Use the common xDCI function to check if the controller is allowed
in the current mode before enabling it. Otherwise, disable the
PCI device if it has been enabled in devicetree.
To make the SOC behavior consistent the XdciEnable config option
is removed in favor of direct control by devicetree.cb and the
mainboards that had defined it were adjusted accordingly.
This was tested on an Eve board with xDCI enabled in devicetree.cb
to ensure the xDCI device is enabled in developer mode and disabled
in normal mode.
Change-Id: Ic3c84beac87452f17490de32082030880834501d
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/25365
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Use soc/common VMX block to enable VMX on supported devices.
Change-Id: Iaa1a6201b431783d709c0509715fa8e8b1ce349a
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/25332
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Youness Alaoui <snifikino@gmail.com>
|
|
Add the NHLT configuration for the max98373 codec to skylake,
taken directly from cannonlake.
This will allow skylake/kabylake boards to use this codec.
Change-Id: Ifb6bf2d31fda25b18d9b1ce2bb721255335d55e4
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/25367
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: HARSHAPRIYA N <harshapriya.n@intel.com>
Reviewed-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
|
|
This change adds a call to heci_reset before attempting to read
ME firmware version. This is important to ensure that both ME and BIOS
are in sync.
BUG=b:76167737
BRANCH=poppy
TEST=Verfied that ME firmware version read does not fail on first boot
after power failure (i.e. removing battery and AC power).
Change-Id: Ib6b39c398d2e1177b087352a4acb8bcf5a9897d6
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/25362
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This patch adds the support for KBL-S MCH and Z270, H270, B250 and
Q250 PCH chips.
BUG=None
BRANCH=None
TEST=Boot with KBL-S CPU and B250/H270 PCHs.
Change-Id: If03abb215f225d648505e05274e2f08ff02cebdc
Signed-off-by: Gaggery Tsai <gaggery.tsai@intel.com>
Reviewed-on: https://review.coreboot.org/25305
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Naresh Solanki <naresh.solanki@intel.com>
|
|
In an attempt at consolidation, commit 0a203d1 [1] introduced
an additional read/write of the MISC_ENABLE msr, as well a bug
which nullified the setting of Intel SpeedStep by inserting said
read/write calls in between another set of read/write calls to the
same msr. Fix by reverting to previous (simpler) implementation.
[1] soc/intel/skylake: Use CPU common library code
https://review.coreboot.org/19566
Test: boot Linux on Librem13v2, read MISC_ENABLE msr and verify
SpeedStep bit correctly set based on devicetree setting.
Change-Id: Id2ac660bf8ea56d45e8c3f631a586b74106a6cc9
Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm>
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/25330
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This change defines IFD_CHIPSET as sklkbl to allow ifdtool to set the
right access control bits for SKL/KBL platforms.
BUG=b:76098647
BRANCH=poppy
TEST=Verified that the access control bits on KBL platforms are set correctly.
Change-Id: I7b2131caa06d6a975e703262931ec0ea519a86aa
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/25307
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
As per PCH BWG 2.5.16, set up LPC IO Enables PCR[DMI] + 2774h bit
[15:0] to the same value program in LPC PCI offset 82h. Also this
cycle decoding is only allowed to set when SRLOCK is not set.
Hence move the required programming from lpc.c to pch.c.
Also only enable COM port ranges if CONFIG_DRIVERS_UART_8250IO
Kconfig is selected.
Change-Id: Ie706735492a450baa653d8a8bb74c6e42f5150b8
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/23866
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
The MMCONF base address and length are set in Kconfig so it does
not need to be redefined by the SOC as the code can just use the
Kconfig variable directly.
Tested on a fizz board to ensure MCFG is still created properly.
Change-Id: I5fd472b1afc8264823a2b9db0f296fbfb6b1ecc0
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/24975
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The ACPI MCFG table is generated with a static end bus number of 255,
which expects that the reserved range in E820 is 256MB. However the
actual MCFG range is configurable with Kconfig, so these two values
may not match when the OS tries to determine the range:
PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
PCI: MMCONFIG 0000 [bus 00-3f] at [mem 0xe0000000-0xe3ffffff] (base 0xe0000000) (size reduced!)
acpi PNP0A08:00: [Firmware Info]: MMCONFIG for domain 0000 [bus 00-3f] only partially covers this bridge
Instead of forcing the end bus number to be 255 use the Kconfig value
to set it based on the current configuration.
Tested on a fizz device to ensure that the kernel no longer complains:
PCI: MMCONFIG for domain 0000 [bus 00-3f] at [mem 0xe0000000-0xe3ffffff] (base 0xe0000000)
Change-Id: I999ea9b72b9deba5f27dd692faa0408427a0bf89
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/24974
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
In PORTSC, Port Enabled/Disabled(PED) is RW1CS.
When there is a USB device attached on system, current UPWE method
will set 1 to PED, this will cause port disabled as it's RW1CS.
This change is inspired by xhci_port_state_to_neutral in linux driver.
It will mask all RO and RWS bits and set WDE and WCE.
BUG=b:70777816
TEST=System won't be awakend from s3 automatically when usb devices
is attached. Also system can be awakend by hotplugging usb
devices under S3.
Change-Id: Ifd4c2d6640fea538e0ac71d7c5e73ab529e94f42
Signed-off-by: Kane Chen <kane.chen@intel.com>
Reviewed-on: https://review.coreboot.org/23848
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This change adds a boot state callback to print ME version after
DEV_ENABLE is complete. Information is printed only if UART_DEBUG is
enabled because talking to ME to get the firmware version adds ~1
second to boot time.
TEST=Verified on Soraka that ME version printed is correct.
Change-Id: I360d5d7420950d5aa255df08be6d7123621b87a8
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/23857
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Julien Viard de Galbert <jviarddegalbert@online.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Once the FADT reports that they don't exist it makes no sense to have
them in ACPI's device tree.
Change-Id: Ice82f0de592b6ca955148479fecc8506a7cdcddc
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reported-by: dhaval.v.sharma@intel.com
Reviewed-on: https://review.coreboot.org/23835
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Rajneesh Bhardwaj <rajneesh.bhardwaj@intel.corp-partner.google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
SKL/KBL PCH does not support legacy devices. This change removes the
setting of ACPI_FADT_LEGACY_DEVICES flag in FADT for SKL/KBL.
It helps Linux kernel to disable controllers required to support legacy
devices only e.g. i8237 DMA controller.
BUG=b:72679357
Change-Id: Ie2a85a719997157f52b0eab7254689f5a56ba05b
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/23833
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Rajneesh Bhardwaj <rajneesh.bhardwaj@intel.corp-partner.google.com>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
These typos were found through manual review and grep.
Change-Id: I6693a9e3b51256b91342881a7116587f68ee96e6
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/23706
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Add group information for each gpio community and use it to
calculate offset of a pad within its group. Original implementation
assumed that the number of gpios in each group is same but that lead to
a bug for cnl since numbers differ for each group.
BUG=b:69616750
TEST=Need to test again on SKL,CNL,APL,GLK
Change-Id: I02ab1d878bc83d32222be074bd2db5e23adaf580
Signed-off-by: Bora Guvendik <bora.guvendik@intel.com>
Reviewed-on: https://review.coreboot.org/22571
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Using common PCR asl for skylake/kabylake platform.
BUG=None
TEST=None
Change-Id: I99ec7c878adaea439108553c0fac9d5abe1bc248
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/23725
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
|
|
* Add Memory Channel Status Enum for Channel detection.
* Align > 80 characters per line.
* Add hob_size == 0 check.
Change-Id: I6ad99de53e280a3db431f706310e6cb22b8b3953
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/23636
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Add PCH,MCH,IGD,I2C,PMC,SMBUS,XCHI and UART IDs for PCH H.
Change-Id: I52b38457bc727735ceb5003cbccda6d7ba3340a2
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Reviewed-on: https://review.coreboot.org/23382
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
ACPI_NHLT happens to be selected twice.
BRANCH=none
BUG=none
TEST=generated fizz .config does not change
Change-Id: Ic525ee07015deb88fff4c15cad9dbbeada8a4479
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: https://review.coreboot.org/23601
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Add a variable to fill out the FSP UPD variable for PCIe HotPlug,
which allows a mainboard to enable HotPlug on individual root ports.
BUG=b:72417777
TEST=enable HotPlug on Eve Root Port 0 (WiFi) and check in linux
that it is identified as a HotPlug capable root port.
Change-Id: I6b1f525e41909a3f81984806c4ef20239032c8d6
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/23511
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
According to doc #543977 Power Architecture Guide, PsysPmax is the
maximum platform power. It maps to the full-scale of Psys signal.
This patch adds a "psys_pmax" member in chip information which allows
boards to set up maximum platform power.
BUG=b:71594855
BRANCH=None
TEST=Set "psys_pmax" in device tree & "USE=fw_debug emerge-fizz
chromeos-mrc coreboot chromeos-bootimage" & ensure correct
PsysPmax value is passed to FSP-S through UPD. Verfied on
KBL-R and KBL-U SKUs.
Change-Id: I44f2e2917a8eb9ce3bb69d9c15899d4c7c5b2883
Signed-off-by: Gaggery Tsai <gaggery.tsai@intel.com>
Reviewed-on: https://review.coreboot.org/23268
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
If given a value for PsysPl3 and/or Pl4, set the
appropriate MSR.
BUG=b:71594855
BRANCH=None
TEST=boot up and check MSRs in OS to make sure values are set as
expected. Test on Fizz, which will set these values in
mainboard.
Change-Id: Idbe04f48079b4fa3302d21acd065f2e4c53dd1ed
Signed-off-by: Shelley Chen <shchen@chromium.org>
Reviewed-on: https://review.coreboot.org/23527
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Gaggery Tsai <gaggery.tsai@intel.com>
|
|
Provide the PM1_TMR information in the FADT even if PmTimerDisabled is
set because PM timer emulation is enabled via MSR 121h so the timer will
still work and can be used by things like Tianocore and Windows.
Change-Id: I78e435c34dd4e6241d345c4d07470621ea051fb8
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/23510
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
The calculation to set up the PM timer emulation is using an
incorrect common timer clock value that was copied from Apollolake.
According to the PDG Skylake and Kabylake clocks are derived from a
24MHz XTAL, not 19.2MHz like Apollolake.
Fixing this value results in the proper "correction value" to be
programmed into the PM timer emulation MSR that matches the raw value
that would be programmed by FSP. (if it were doing MpInit)
Old PM timer correction value: 0x2fba2e25
New PM timer correction value: 0x262e8b51
Change-Id: Ib2bb3cb1938ae34cfa7aef177bef6fc24da73335
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/23509
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Now SOC code can select the require UDK support package for any
platform going forward with FSP2.0 model.
Change-Id: Ie6d1b9133892c59210a659ef0ad4b59ebf9f1e45
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/23426
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This change adds support for:
1. Handling thermal trip points change event handler based on device
mode.
2. Returning thermal trip point temperatures based on the device mode.
BUG=b:72554519
Change-Id: Ife48af76ceb7a39abd1fac8ef1f77db7e65ab43e
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/23462
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
|
|
Change-Id: I12ebed30de4df9814ccb62341c7715fc62c7f5b9
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Signed-off-by: Pratik Prajapati <pratikkumar.v.prajapati@intel.com>
Reviewed-on: https://review.coreboot.org/23431
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Right now dw_i2c_get_soc_cfg() is expecting the SoC to implement
that callback for obtaining the bus config. However, we're currently
forcing another parameter of struct device so one can do the lookup.
This works for Intel-based systems since the struct device was needed
to program the BAR, etc. However, from an API standpoint, it just
complicates matters by needing to obtain the struct device. The SoC
already has knowlege of its own devices so it can get the config
itself by bus number. Therefore, remove that contraint from the API.
BUG=b:70232394
Change-Id: Id8558f5deedda0963a46a532a7bf984e168fb270
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/23420
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Rename the device ID macros as per the skylake PCH H external design
specification.
Change-Id: I4e80d41380dc1973d02bc69ac32aad5c4741a976
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Reviewed-on: https://review.coreboot.org/23381
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
The FSP 2.0 Memory_Info_HOB for KBL is not sending
"MemoryType" value as what is required for SMBIOS Table
according to SMBIOS Spec. Thus, converting the value
retrieved from FSP HOB to the correct value.
This change will not be required for upcoming SOCs since
FSP have fixed this issue in its next platforms and thus it
will take care and send the correct value in "MemoryType"
field based on SMBIOS spec. Thus this conversion from coreboot
will not be required in the next platfoms. "MemoryType" value
can be directly passed to dimm_info_fill() function.
BUG=none
BRANCH=none
TEST=Tested in Soraka, and getting the value as 0x1D for
LPDDR3 memory. dmidecode (latest version 3.1) Command Type 17
will also show correct information. Currently, it was showing
"Unknown".
Change-Id: I75d6cca464680a88bf836e25bf5440a9cdbc738e
Signed-off-by: Barnali Sarkar <barnali.sarkar@intel.com>
Reviewed-on: https://review.coreboot.org/23384
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Rename the following functions to ensure it's clear that the designware
i2c host controller driver is the one that these functions are
associated with:
i2c_get_soc_cfg() -> dw_i2c_get_soc_cfg()
i2c_get_soc_early_base() -> dw_i2c_get_soc_early_base()
i2c_soc_devfn_to_bus() -> dw_i2c_soc_devfn_to_bus()
i2c_soc_bus_to_devfn() -> dw_i2c_soc_bus_to_devfn()
BUG=b:72121803
Change-Id: Idb7633b45a0bb7cb7433ef5f6b154e28474a7b6d
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/23371
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This patch ensures common block has option to reserve IO resources
based on SOC requirements. Also add pch_lpc_ prefix to maintain
same function nomenclature across all intel common block.
Change-Id: Ic00af688104bcea1aff06be6cbb20208a60e5f1d
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/23201
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This patch provides an option for non-chrome devices to make use of
FSP-T for performing cache-as-ram initialization. Majority of IOTG users
are using FSP-T for CAR implementation and aren't able to select FSP_CAR
Kconfig from SoC without conflicting with existing CAR config.
TEST=Ensure that both the Chrome platform and non Chrome OS platform
can select either CAR implementation based on Kconfig options
FSP_CAR or CAR_NEM_ENHANCED. By default Chrome platform choose
CAR_NEM_ENHANCED Kconfig and non Chrome platforms choose
FSP_CAR by default.
Change-Id: If565b649fe1c2abdbcf0a740c15db7253c084ae7
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/23161
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
According to Intel document #559100 KBL EDS v2.8, section 7.2
DC specifications, the IccMax setting for KBL-U, KBL-U42 and
Celeron/Pentium are different. This patch overrides the IccMax
settings for KBL-U/R/Y since device tree could not handle all
KBL-U/R combinations when multiple SKUs are adopted in a project.
Besides, it is inefficient to maintain the same code for all
variants. Hence, place it in the common code so that all variants
could leverage the benefits.
+----------------+-------------+---------------+------+-----+
| Domain/Setting | SA | IA | GTUS | GTS |
+----------------+-------------+---------------+------+-----+
| IccMax(KBL-U/R)| 6A(U42) | 64A(U42) | 31A | 31A |
| | 4.5A(Others)| 29A(Celeron) | | |
| | | 32A(i3/i5) | | |
+----------------+-------------+---------------+------+-----+
| IccMax(KBL-Y) | 4.1A | 24A | 24A | 24A |
+----------------+-------------+---------------+------+-----+
BUG=b:71369428
BRANCH=None
TEST=Remove icc_max setting from devicetree & emerge-fizz coreboot
chromeos-bootimage & Ensure the KBL-U42, KBL-U22 and Celeron
SKUs are identified correctly and IccMax settings are passed
to FSPS correctly.
Change-Id: I291462b73d3fbd17f17975de7fd77dc48ca99251
Signed-off-by: Gaggery Tsai <gaggery.tsai@intel.com>
Reviewed-on: https://review.coreboot.org/23060
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This change provides option in devicetree and feeds the option to
FSP SataPwrOptEnable UPD for power saving purpose
BUG=b:70491485
Change-Id: I9099c5c97765a118bdee64da303cb3ba6ceb951b
Signed-off-by: Kane Chen <kane.chen@intel.com>
Reviewed-on: https://review.coreboot.org/23018
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
weak function
This patch ensures all soc function name is having _soc_ prefix
in it.
TEST=Able to compile SMM common code for all supported SOC.
Change-Id: Iab1b2f51eaad87906e35dbb9e90272590974e145
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/22973
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
New UPD PcieRpClkSrcNumber introduced in FSP V2.9.2 to configure
clock source number of PCIe root ports. This UPD array is set to clock
source number(0-6) for all the enabled PCIe root ports, invalid(0x1F)
is set for disabled PCIe root ports.
BUG=b:70252901
BRANCH=None
TEST= Perform the following
1. Build and boot soraka
2. Verify PCIe devices list using lspci command
3. Perform Basic Assurance Test(BAT) on soraka
Change-Id: I95ca0d893338100b7e4d7d0b76c076ed7e2b040e
Signed-off-by: Divya Chellap <divya.chellappa@intel.com>
Reviewed-on: https://review.coreboot.org/22947
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
BUG=b:70232394
BRANCH=none
TEST=emerge-reef coreboot
emerge-glados
Change-Id: Idb453a4d2411163e6b4a8422310bf272eac5d379
Signed-off-by: Chris Ching <chingcodes@chromium.org>
Reviewed-on: https://review.coreboot.org/22822
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This patch ensures skylake soc is using common SMM code
from intel common block.
TEST=Build and boot soraka/eve
Change-Id: I8163dc7e18bb417e8c18a12628988959c128b3df
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Signed-off-by: Brandon Breitenstein <brandon.breitenstein@intel.com>
Reviewed-on: https://review.coreboot.org/22826
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Original commit hash aeb2d64c85ca2c3a77f50d57e3a92f6fc0a5c2d3 (soc/intel/skylake:
Enable power button SMI when jumping to payload)
Change-Id: Ia4fe2694006baf24ed475c85aaffa6a0d2a6031d
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/22868
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
TEST=KBL_RVP is able to power on after reconnecting power supply.
Change-Id: Ic707164a576ffb25418eb6553843cd8edc608800
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/22839
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
In the fast spi support implement the callback for flash_protect().
This removes the need for having SOC_INTEL_COMMON_SPI_FLASH_PROTECT
Kconfig option as well spi_flash_get_fpr_info() and separate
spi_flash.[ch].
BUG=b:69614064
Change-Id: Iaf3b599a13a756262d3f36bae60de4f7fd00e7dc
Signed-off-by: Aaron Durbn <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/22881
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
|
|
Add parameters to configure the integrated LAN via FSP. Since
this takes over a PCI CLKREQ# pin it needs to know which pin
it should use, and there are additional parameters for LTR and
a "K1 power save" feature.
This was tested on a KBL-R board with integrated LAN, verifying
that the device is functional under Linux with the e1000e driver.
Change-Id: Idb200cec90a3c0d4d9c914bae9983a3bcdafcd06
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/22856
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Currently, "tcc_offset" defined in devicetree is overwritten by
Intel FSP-S UPD "TccActivationOffset".
This patch will make "TccActivationOffset" refer to "tcc_offset".
TEST=check if MSR (0x1a2[29:24]) value is updated with "tcc_offset"
by iotools (rdmsr 0 0x1a2).
Change-Id: Ibc6f33bea19a1d59bc7e407815210942b38f0702
Signed-off-by: marxwang <marx.wang@intel.com>
Reviewed-on: https://review.coreboot.org/22818
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Intel common PCI driver is handle PCI subsystem ID
programming, hence no need to have an explicit soc
function to do the same.
TEST=PCI subsystem id is getting programming during
pci enumeration.
Change-Id: Iead57a286b26d532e578cfff99f412c23fd4c2fe
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/22769
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
According to the PCH BIOS Spec (Doc#549921/Rev-2.3.4),
section 2.5.1.6, it is a requirement to program the same
value programmed in LPC "PCI offset 82h" into "PCR[DMI]+2774h"
to fully enable the Lpc IO enable decoding which is missing in
current source.
Without above changes, Skylake Saddlebrook platform with a
SIO does not boot.
Change-Id: Ief26e2718325b9d74ea0f83d47d2f917e0972173
Signed-off-by: praveen <praveenx.hodagatta.pranesh@intel.com>
Reviewed-on: https://review.coreboot.org/22819
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Adapted from Chromium commit d6655eb
[Skylake: create UPD Interface for acoustic noise tuning]
Add FSP 1.1 params needed for acoustic mitigation on google/caroline
(to be upstreamed in a subsequent commit).
TEST: build/boot google/caroline
Change-Id: Ifb36ecef8c1735c63a5322d952929e9c34cddfb9
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/22524
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
This patch ensures that all required information for
pch/mch/igd deviceid and revision available in single
stage and make use of local references.
TEST=Build and boot soraka/eve
Change-Id: I6f7f219536831210750a486ee3b3308d6f285451
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/22756
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
PCI resources MMIO space/bus master enabling is handled inside
pch_dev_enable_resources() from common device code. Hence
no need to have an explicit soc function to do the same.
TEST=lspci from kernel console shows same pci device list
without and without this patch.
Change-Id: I005e486dd435e9c61ae3f5dfe3ff0e8f688d16e1
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/22755
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Clean up and move UART related code under a single uart.c file.
Change-Id: I7ed03fc5fe79e38350d7edc70ad55d54db780fed
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-on: https://review.coreboot.org/22753
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
|
|
TEST=Build and boot soraka/eve.
Change-Id: I416226d0374700cea6eea602f839c3d17f1f39a6
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/22615
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This partially reverts commit a7b97510aeb1652fd0006c9b2d10df6568f37e2e.
For the internal eMMC to be used by Windows for installation,
the CARD device and _RMV methods are required. Without them,
Windows does not see/show the eMMC as a valid installation
target.
TEST: boot google/chell with Tianocore payload and install
Windows 10 to the internal eMMC drive.
Change-Id: I04819ff16ab4cb0d2ea6e1c7f47179f5dacb7cfd
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/22684
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
DSX_CFG provides a config option to disable internal pull-down on
AC_PRESENT. This change updates macro name to reflect this correctly.
BUG=b:69983729
Change-Id: I291112858c4ce36667edf30fe303fed437baf5d2
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/22688
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
SoC needs to select specific macros to compile commom PMC code.
TEST=Build and boot KBL (soraka/eve), APL (reef)
Change-Id: Iacc8da986c01e9ac7516643dafc6d932ebe0ee5e
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/22563
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
PMC logic shuts down the thermal sensor when CPU is in a C-state and
DTS Temp <= Low Temp Threshold in case Dynamic Thermal Shutdown in
S0ix is enabled.
BUG=b:69110373
BRANCH=none
TEST=Ensure Thermal Device(B0: D20: F2) TSPM offset 0x1c[LTT (8:0)]
value is 0xFA.
Change-Id: I94d09a28bf1ea07a53cfa04c54752358bafca610
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/22419
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
TEST=Build and boot soraka/eve.
Change-Id: I8be2a90dc4e4c5eb196af57045d2a46b7f0c9722
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/22609
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|