Age | Commit message (Collapse) | Author |
|
Enable mainboard Kconfig to select between FSP 2.0 & 1.1 driver to be
used.
If mainboard Kconfig selects MAINBOARD_USES_FSP2_0 the FSP2_0 driver is
used else FSP1_1.
Change-Id: I724aaa87c2b0b8f6ddb18f61af9c37176ef632f2
Signed-off-by: Naresh G Solanki <naresh.solanki@intel.com>
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/17044
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
In FSP1.1 all the platform resets including global was handled
on its own without any intervention from coreboot.
In FSP2.0, any reset required will be notified to coreboot
and it is expected that coreboot will perform platform reset.
Hence, implement platform global reset hooks in coreboot. If Intel
ME is in non ERROR state then MEI message will able to perform
global reset else force global reset by writing 0x6 or 0xE to
0xCF9 port with PCH ETR3 register bit [20] set.
BUG=none
BRANCH=none
TEST=Verified platform global reset is working with MEI
message or writing to PCH ETR3.
Change-Id: I57e55caa6d20b15644bac686be8734d9652f21e5
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/16903
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
As per ME BWG, there are two mechanism to generate a Global
Reset (resets both host and Intel ME), one is through CF9h
IO write of 6h or Eh with "CF9h Global Reset" (CF9GR) bit set,
PMC PCI offset ACh[20]. Another is to issue the Global Reset
MEI message. Because any attempts to cause global reset without
synchronizing the two sides might cause unwanted side effects,
such as unwritten flash data that will get destroyed if the
host were to cause a global reset without informing Intel ME
firmware, the recommended method is to send a Global Reset MEI
message when the following conditions are met:
The PCH chipset firmware just needs to complete the Intel ME
Interface #1 initialization and check the Intel ME HFSTS state
if Intel ME is not in ERROR state and is accepting MEI commands
then firmware should be able to use Global Reset MEI message to
trigger global reset.
Furthermore, if Intel ME is in ERROR state, BIOS can use I/O 0xCF9
write of 0x06 or 0x0E command with PCH ETR3 register bit [20]
to perform the global reset.
BUG=none
BRANCH=none
TEST=Verified Global Reset MEI message is able to perform platform
global issue in ME good state.
Change-Id: If326a137eeadaa695668b76b84c510e12c546024
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/16902
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This patch programs and enables BAR for ME (bus:0/
device:0x16/function:0) device to have early ME communication.
BUG=none
BRANCH=none
TEST=Verified Global Reset MEI message can able to perform platform
global reset during romstage.
Change-Id: I99ce0ccd42610112a361a48ba31168c9feaa0332
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/17016
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
VBOOT_EC_SLOW_UPDATE should be selected if EC_GOOGLE_CHROMEEC is used as
building coreboot with Chrome OS support & without Chrome EC gives a
build error in coreboot.
Change-Id: I77eed0e1bdc1ba49381b72e21b0e18f573cadff0
Signed-off-by: Naresh G Solanki <naresh.solanki@intel.com>
Reviewed-on: https://review.coreboot.org/17020
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Change-Id: Ia9c1c065f20bf2b37afc7485ef8df3abd35e2f14
Reviewed-on: https://review.coreboot.org/16607
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Add FSP 2.0 support in ramstage.
Populate required Fsp Silicon Init params and configure mainboard
specific GPIOs.
Define function fsp_soc_get_igd_bar needed by fsp2.0 driver for
pre OS screens.
Change-Id: Ib38ca7547b5d5ec2b268698b8886d5caa28d6497
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Signed-off-by: Naresh G Solanki <naresh.solanki@intel.com>
Reviewed-on: https://review.coreboot.org/16592
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Populate SoC related Memory initialization params.
Post memory init, set DISB, setup stack and MTRRs using the postcar
funtions provided in postcar_loader.c.
TEST=Build and boot kunimitsu, dram initialization done.
ramstage is loaded.
Change-Id: I8d943e29b6e118986189166d92c7891ab6642193
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Signed-off-by: Naresh G Solanki <naresh.solanki@intel.com>
Reviewed-on: https://review.coreboot.org/16315
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Commit 93ef3ff makes the following only print the part number when
the ROM is built. In Makefile.inc, $(MAINBOARDDIR) is the variable
that has the quotes stripped off from $(CONFIG_MAINBOARD_DIR), so
use it instead of $(MAINBOARD_DIR).
build_complete:: coreboot
printf "\nBuilt %s (%s)\n" $(MAINBOARD_DIR) \
$(CONFIG_MAINBOARD_PART_NUMBER)
Change-Id: I729a583182937db7a926eb75aa28dfb53360046c
Signed-off-by: Iru Cai <mytbk920423@gmail.com>
Reviewed-on: https://review.coreboot.org/16410
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
All but ga-g41m-es2l/cmos.default had multiple final newlines.
ga-g41m-es2l/cmos.default had no final newline.
Change-Id: Id350b513d5833bb14a2564eb789ab23b6278dcb5
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/16361
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Antonello Dettori <dev@dettori.io>
|
|
Change-Id: Ifc47f103492a2cd6c818dfd64be971d34afbe0a4
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/16324
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Add Initial pieces of code to support fsp2.0 in skylake keeping
the fsp1.1 flow intact.
The soc/romstage.h and soc/ramstage.h have a reference to
fsp driver includes, so split these header files for
each version of FSP driver.
Add the below files,
car_stage.S:
Add romstage entry point (car_stage_entry).
This calls into romstage_fsp20.c and aslo handles
the car teardown.
romstage_fsp20.c:
Call fsp_memory_init() and also has the callback
for filling memory init parameters.
Also add monotonic_timer.c to verstage.
With this patchset and relevant change in kunimitsu mainboard,
we are able to boot to romstage.
TEST= Build and Boot Kunimitsu with PLATFORM_USES_FSP1_1
Build and Boot Kunimitsu to romstage with PLATFORM_USES_FSP2_0
Change-Id: I4309c8d4369c84d2bd1b13e8ab7bfeaaec645520
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/16267
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
|
|
Add Kabylake specific Graphics IDs in report_platform.c and igd.c.
BUG=none
BRANCH=none
TEST=Built and boot kunimitsu
Change-Id: I3b810d0ff51eb51d396b783e282779aefb2dcb8c
Signed-off-by: Barnali Sarkar <barnali.sarkar@intel.com>
Reviewed-on: https://review.coreboot.org/16329
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
When UART_DEBUG is enabled bootblock size grows more than the current
32K. Bump this up to 48K.
Change-Id: I580137dfdc9b4ad226c866f2b23b159bd820c62c
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/16317
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
The chromium tree is currently using a different config for
Chrome OS than what is being built in coreboot.org. Align those
settings to reflect how skylake Chrome OS boards are actually
shipped to provide proper parity between coreboot.org and chromium.
Change-Id: I7ab9c1dfa8c6be03ac2125fb06cb7022f3befa97
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/16313
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Calling halt in poweroff when in SMM prevents SLP_SMI to be triggered
preventing the system from entering sleep state. Fix this by calling
halt only if ENV_SMM is not true.
BUG=chrome-os-partner:56395
Change-Id: I3addc1ea065346fbc5dbec9d1ad49bbd0ae05696
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/16259
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
If the boot device is SPI flash use the common one in the
early stages. While tweaking the config don't auto select
SPI_FLASH as that is handled automatically by the rest of the
build system.
BUG=chrome-os-partner:56151
Change-Id: Ifd51a80fd008c336233d6e460c354190fcc0ef22
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/16202
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Using malloc() in SPI code is unnecessary as there's only
one SPI device that the SoC support code handles: boot
device. Therefore, use CAR to for the storage to work around
the current limiations of the SPI API which expects one to
return pointers to objects that are writable. Additionally,
include the SPI support code as well as its dependencies in
all the stages.
BUG=chrome-os-partner:56151
Change-Id: I0192ab59f3555deaf6a6878cc31c059c5c2b7d3f
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/16196
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Lee Leahy <leroy.p.leahy@intel.com>
|
|
Indicate to the build system that a platform provides support
for a writable boot device. The following will provide the
necessary support:
COMMON_CBFS_SPI_WRAPPER users
soc/intel/apollolake
soc/intel/baytrail
soc/intel/braswell
soc/intel/broadwell
soc/intel/skylake
The SPI_FLASH option is auto-selected if the platform provides
write supoprt for the boot device and SPI flash is the boot
device.
Other platforms may provide similar support, but they do that
in a device specific manner such as selecting SPI_FLASH
explicitly. This provides clearance against build failures
where chipsets don't provide SPI API implementations even
though the platform may use a SPI flash to boot.
BUG=chrome-os-partner:56151
Change-Id: If78160f231c8312a313f9b9753607d044345d274
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/16211
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
DCACHE_RAM_SIZE_TOTAL is set to 0x40000 and is being used to
set up CAR. Whereas DCACHE_RAM_SIZE which is set to 0x10000
is used to calculate the _car_region_end in car.ld. If the FSP CAR
requirement is greater than or even close to DCACHE_RAM_SIZE then,
the CAR region for FSP will be determined to be below the overall
CAR region boundary i.e, out of CAR memory range.
This is working with FSP 1.1 because we provide the FspCarSize
and FspCarBase explicitly in a UPD. Hence, FSP is still able to
use the upper region of CAR memory for its purpose.
However, it will be a problem in case of FSP2.0 where FSP usable CAR
is calculated using _car_region_end.
So, Remove the the use of DCACHE_RAM_SIZE_TOTAL and set
DCACHE_RAM_SIZE to correct value i.e, 0x40000(256KB)
Change-Id: Ie2cb8bb0705a37edb3414850d7659f8a3dd6958b
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/16236
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins)
|
|
There is a lot of code that is being referred to in bootblock but
resides under skylake/romstage folder. Hence move this code
into skylake/bootblock, and update the relevant header files
and Makefiles.
TEST=Build and Boot kunimitsu.
Change-Id: If94e16fe54ccb7ced9c6b480a661609bdd2dfa41
Signed-off-by: Naresh G Solanki <naresh.solanki@intel.com>
Reviewed-on: https://review.coreboot.org/16225
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Prepare Skylake for FSP2.0 support.
We do not use FSP-T in FSP2.0 driver, hence guard the
FspTempRamInit call under a switch.
In addition to the current early PCH configuration
program few more register, so all in all we do the following,
* Program and enable ACPI Base.
* Program and enable PWRM Base.
* Program TCO Base.
* Program Interrupt configuration registers.
* Program LPC IO decode range.
* Program SMBUS Base address and enable it.
* Enable upper 128 bytes of CMOS.
And split the above programming into into smaller functions.
Also, as part of bootblock_pch_early_init we enable decoding
for HPET range. This is needed for FspMemoryInit to store and
retrieve a global data pointer.
And also move P2SB related definitions to a new header file.
TEST=Build and boot Kunimitsu
Change-Id: Ia201e03b745836ebb43b8d7cfc77550105c71d16
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Signed-off-by: Barnali Sarkar <barnali.sarkar@intel.com>
Reviewed-on: https://review.coreboot.org/16113
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Program MCHBAR, DMIBAR, EPBAR, EDRAMBAR and GDXCBAR.
Also program the PAM registers. The system agent was being
programmed in romstage during pre-console initialization, after
moving to C_ENVIRONMENT bootblock this was missing, restoring
the same.
TEST=Build and Boot Kunimitsu
Change-Id: Iaf310cfb83e58eb8d5affb481dfc343f5d45961b
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/16224
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
The SPI host controller for the SPI boot device doesn't allow
normal probing because it uses the hardware sequencer all
the time. Therefore, it's pointless to include unnecessary
SPI flash drivers.
BUG=chrome-os-partner:56151
Change-Id: Ifcc6492b4bccf7d01b121d908976c9087d12deb0
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/16189
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
The function name "pmc_tco_regs" is changed to "smbus_tco_regs"
since TCO offsets belongs to SMBUS PCI device.
BUG=none
BRANCH=none
TEST=Built and booted kunimitsu
Change-Id: I4ac26df81a8221329f2b45053dd5243cd02f8ad7
Signed-off-by: Barnali Sarkar <barnali.sarkar@intel.com>
Reviewed-on: https://review.coreboot.org/16155
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
The variable MAINBOARD_DIR already has the quotes stripped off.
Change-Id: Ib434ce92bdbc49180fb3f713b26d65ba4cf8c441
Signed-off-by: Martin Roth <martinroth@chromium.org>
Reviewed-on: https://review.coreboot.org/16117
Tested-by: build bot (Jenkins)
Reviewed-by: Lee Leahy <leroy.p.leahy@intel.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Since RTC is now a Kconfig ensure RTC is selected on the
x86 chipsets which are in Chrome OS devices. This allows
the eventlog to have proper timestamps instead of all
zeros.
BUG=chrome-os-partner:55993
Change-Id: I24ae7d9b3bf43a5791d4dc04aae018ce17fda72b
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/16086
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
List of changes done here in this patch
1. Remove CARD definition from EMMC and SD Card Controller in scs.asl
since _RMV method does not get evaluated while setting up removable
attribute in sysfs in kernel.
"cat /sys/block/mmcblk1/removable" this command always returns 0.
This CARD Device includes _ADR which follows SDIO Bus format. But,
SD/EMMC sits on PCI Bus.
Hence this CARD Device specific _ADR code is also not needed.
2. Remove Base Address for ACPI debug output memory buffer in
systemagent.asl as it is not getting used throughout the code.
BUG=none
BRANCH=none
TEST=Build and boot kunimitsu
Change-Id: I29effaffdafcc21e26445ec3c54aedecdbc50274
Signed-off-by: Barnali Sarkar <barnali.sarkar@intel.com>
Reviewed-on: https://review.coreboot.org/16068
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
|
|
Program PIRQ Routing with correct values, as done by FSP, and also in
'soc/intel/skylake/romstage/pch.c' file. If not done, these values get
overridden by "0" during PxRC -> PIRQ programming in ramstage, in
'soc/intel/skylake/lpc.c' file pch_pirq_init()function.
BUG=none
BRANCH=none
TEST=Build and boot kunimitsu
Change-Id: Ibeb9a64824a71c253e45d6a1c6088abd737cf046
Signed-off-by: Barnali Sarkar <barnali.sarkar@intel.com>
Reviewed-on: https://review.coreboot.org/16044
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
|
|
Here is the list of items of code cleanup
1. Define TCO registers in smbus.h and not in pmc.h (as per EDS).
2. Include smbus.h wherever these TCO register defines were used.
3. Remove duplication of define in gpio_defs.h.
4. Remove unnecessary console.h include from memmap.h as no prints done.
5. Remove unnecessary comment from pch.c.
BUG=none
BRANCH=none
TEST=Built and boot kunimitsu.
Change-Id: Ibe6d2537ddde3c1c7f8ea5ada1bfaa9be79c0e3b
Signed-off-by: Barnali Sarkar <barnali.sarkar@intel.com>
Reviewed-on: https://review.coreboot.org/16027
Tested-by: build bot (Jenkins)
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
|
|
Adding kabylake device ids for chip inits.
Skylake and Kabylak do not differ much, the intention
is to support both SoCs in the same code base.
Change-Id: I9ff4c6ca08fe681798001ce81cca2c085ce32325
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/16049
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
This corrects the address of the I2C5 Device. The I2C
Controller #5 is on PCI Bus 0: Device 25: Function 1. The ACPI
Address Encoding Logic is - High word = Device #.
Low word = Function #.
So, I2C5 (_ADR) = 0x0019 0001.
BUG=none
BRANCH=none
TEST=Build and boot kunimitsu
Change-Id: I4719a843260ef58cc2307e909e9ccbffea519177
Signed-off-by: Barnali Sarkar <barnali.sarkar@intel.com>
Reviewed-on: https://review.coreboot.org/16048
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
1. skylake does not support UART over I/O. So, NO_UART_ON_SUPERIO needs
to be selected by default.
2. Move BOOTBLOCK_CONSOLE under UART_DEBUG.
3. Include bootblock/uart.c only if UART_DEBUG is selected.
Change-Id: I4e996bea2a25b3b1dfb9625d97985a9d3473561b
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/16025
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
|
|
Change-Id: I7930d5cded290f2605d0c92a9c465a3f0c1291a2
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/15974
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Change-Id: I7f0d3400126d593bad8e78f95e6b9a378463b4ce
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/15963
Tested-by: build bot (Jenkins)
Reviewed-by: Omar Pakker
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Testing for "devfn < 0" on an unsigned doesn't work, and i2c_bus_to_devfn
returns an int (with -1 for "error"), so use int for devfn.
Change-Id: I7d1cdb6af4140f7dc322141c0c018d8418627434
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Found-by: Coverity Scan #1357450, #1357449
Reviewed-on: https://review.coreboot.org/15964
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
This removes the newlines from all files found by the new
int-015-final-newlines script.
Change-Id: I65b6d5b403fe3fa30b7ac11958cc0f9880704ed7
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/15975
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Use the ACPI generator for creating the Chrome OS gpio
package. Each mainboard has its own list of Chrome OS
gpios that are fed into a helper to generate the ACPI
external OIPG package. Additionally, the common
chromeos.asl is now conditionally included based on
CONFIG_CHROMEOS.
Change-Id: I1d3d951964374a9d43521879d4c265fa513920d2
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/15909
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
1. Enable SoC SD_CMD/D* signals pull-down of 20k when SD-card
is removed. When SD-card is disconnected, the pull-down is
disabled.
2. Provide path for weak leakage from buffers of SD_CMD/D* signal
to be grounded. Thus dropping voltage on the SD_CMD/D* signals to ~0V.
BUG=chrome-os-partner:54421
TEST=no power leakage when SDCard isn't inserted on skylake platform
Change-Id: I567199b172841125f8916a61a76005cfdaa62eb8
Signed-off-by: Zhuo-hao.Lee <zhuo-hao.lee@intel.com>
Reviewed-on: https://review.coreboot.org/15910
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
FSP temp ram init was getting called earlier from ROMCC bootblock.
Now with C entry boot block, it is needed to locate FSP header and
call FspTempRamInit.
Hence add fsp 1_1 driver code to locate FSP Temp ram and execute.
BUG=chrome-os-partner:55357
BRANCH=none
TEST=Built kunimitsu and ensure FSP Temp Ram Init return success
Change-Id: If40b267777a8dc5c473d1115b19b98609ff3fd74
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/15787
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
List of activity performing in this patch
- early PCH programming
- early SA programming
- early CPU programming
- mainborad early gpio programming for UART and SPI
- car setup
- move chipset programming from verstage to post console
BUG=chrome-os-partner:55357
BRANCH=none
TEST=Built and booted kunimitsu till POST code 0x34
Change-Id: If20ab869de62cd4439f3f014f9362ccbec38e143
Signed-off-by: Barnali Sarkar <barnali.sarkar@intel.com>
Signed-off-by: Naveen Krishna Chatradhi <naveenkrishna.ch@intel.com>
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/15785
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Enable cache-as-ram and prepare for c entry in bootblock.
BUG=chrome-os-partner:55357
BRANCH=none
TEST=Built and booted kunimitsu till POST code 0x2A
Credits-to: Aaron Durbin <adurbin@chromium.org>
Signed-off-by: Barnali Sarkar <barnali.sarkar@intel.com>
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Change-Id: I3412216cdf8ef7e952145943d33c3f07949da3c1
Reviewed-on: https://review.coreboot.org/15784
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
BUG=chrome-os-partner:55639
Change-Id: I7a536bc1cab51e7c942b2e0e48dfe18d8de08a6e
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/15925
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins)
|
|
With VBOOT_VERIFY_FIRMWARE separated from CHROMEOS, move recovery and
developer mode check functions to vboot. Thus, get rid of the
BOOTMODE_STRAPS option which controlled these functions under src/lib.
BUG=chrome-os-partner:55639
Change-Id: Ia2571026ce8976856add01095cc6be415d2be22e
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/15868
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
VBOOT_VERIFY_FIRMWARE should be independent of CHROMEOS. This allows use
of verified boot library without having to stick to CHROMEOS.
BUG=chrome-os-partner:55639
Change-Id: Ia2c328712caedd230ab295b8a613e3c1ed1532d9
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/15867
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
This allows the board to save the recovery request in case of unexpected
reboots caused by FSP.
With recovery module in vboot handling the saving of recovery reason
across reboots, there is no need to have special fsp reset handling
under soc.
BUG=chrome-os-partner:55431
Change-Id: I0b7ce14868a322072d3e60c1dae43f211b43fdbf
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/15804
Tested-by: build bot (Jenkins)
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
1. Remove unused functions/structures.
2. Add checks for NULL return values.
3. Change prefixes to vb2 instead of vboot for functions used internally
within vboot2/
4. Get rid of vboot_handoff.h file and move the structure definition to
vboot_common.h
5. Rename all functions using handoff structure to have prefix
vboot_handoff_*. All the handoff functions can be run _only_ after cbmem
is online.
6. Organize vboot_common.h content according to different
functionalities.
BUG=chrome-os-partner:55431
Change-Id: I4c07d50327d88cddbdfbb0b6f82c264e2b8620eb
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/15799
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
|
|
All the mainboards share the same config options for CHROMEOS. Instead
of duplicating those in every mainboard, move the CHROMEOS config to SoC
and make it dependent on MAINBOARD_HAS_CHROMEOS.
BUG=chrome-os-partner:55431
Change-Id: Iafabb6373dfe16aaf0fe2cbc4e978952adeb403e
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/15822
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
|
|
Implement poweroff() by putting the chipset into ACPI S5 state.
BUG=chrome-os-partner:54977
Change-Id: I9288dcee13347a8aa3f822ca3d75148ba2792859
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/15688
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins)
|
|
Transition to using the common Intel ACPI hardware definitions
generic ACPI definitions.
BUG=chrome-os-partner:54977
Change-Id: I5f2aa424a167092b570fda020cddce5ef906860a
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/15671
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Lee Leahy <leroy.p.leahy@intel.com>
|
|
The ramstage main() in lib/hardwaremain.c has the logic
to set the ACPI sleep state based on romstage_handoff. Thus,
there's no need to do it a second time.
Change-Id: I75172083587c8d4457c1466edb88d400f7ef2dd0
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/15662
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
There is a second ACPI _DSD document from the UEFI Forum that details
how _DSD style tables can be nested, creating a tree of similarly
formatted tables. This document is linked from acpi_device.h.
In order to support this the device property interface needs to be
more flexible and build up a tree of properties to write all entries
at once instead of writing each entry as it is generated.
In the end this is a more flexible solution that can support drivers
that need child tables like the DA7219 codec, while only requiring
minor changes to the existing drivers that use the device property
interface.
This was tested on reef (apollolake) and chell (skylake) boards to
ensure that there was no change in the generated SSDT AML.
Change-Id: Ia22e3a5fd3982ffa7c324bee1a8d190d49f853dd
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/15537
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Add the function defined in gpio.h to translate a gpio_t into a
value for use in an ACPI GPIO pin table.
For skylake this just returns the gpio_t value as the pins are
translated directly and they are all in the same ACPI device.
Change-Id: I00fad1cafec2f2d63dce9f7779063be0532649c7
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/15520
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Have the Skylake SOC generate ACPI timing values for the enabled I2C
controllers instead of passing it in the DSDT with static timings.
The timing values are generated from the controller clock speed and
are more accurate than the hardcoded values that were in the ASL which
were originally copied from Broadwell where the controller is running
at a different clock speed...
Additionally it is now possible for a board to override the values
using devicetree.cb. If zero is passed in for SCL HCNT or LCNT then
the kernel will generate its own timing using the same forumla, but if
the SDA hold time value is zero the kernel will NOT generate a correct
value and the SDA hold time may be incorrect.
This was tested on the Chell platform to ensure all the I2C devices on
the board are still operational with these new timing values.
Change-Id: I4feb3df9e083592792f8fadd7105e081a984a906
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/15291
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
The nhlt_soc_serialize() and nhlt_soc_serialize_oem_overrides()
functions should be able to be leveraged on all Intel SoCs
which support NHLT. Therefore provide that functionality and
make skylake use it.
Change-Id: Ib5535cc874f2680ec22554cecaf97b09753cacd0
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/15490
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins)
|
|
Utilize the new NHLT helper functions by driving the NHLT
endpoints through data descriptors.
Change-Id: I80838214d3615b83d4939ec2d96a4fd7050d5920
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/15488
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Whitespace fix for improper space usage for indention.
Change-Id: Ia6470bf152c57786d2d7f3d35bbf0609a2ee3ba2
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/15487
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins)
|
|
spi_init should be run early enough in ramstage so that any init
calls (e.g. mainboard_ec_init) that write on flash have right
permissions set.
Change-Id: I9cd3dc723387757951acd40449d4a41986836d2a
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/15235
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Support the common Intel LPSS I2C driver for the 6 I2C bus controllers
that are present on the Skylake-LP PCH with a 120 mHz clock. The
required lpss_i2c_base_address() method is implemented separately for
verstage/romstage and ramstage environments.
This provides methods to convert to and from "struct device" and the
I2C controller bus number for that device. These are used to provide
support for the "I2C Bus Operations" that are present in the coreboot
devicetree.
To support the I2C controller before ramstage an early init function
is provided to do minimal initializaiton of the PCI device and assign
a temporary base address for use before memory. The final base
address is assigned during device enumeration and used during ramstage.
Because it is usually not necessary to enable I2C controllers before
ramstage a config register for the devicetree is provided to perform
early initialization of this controller. In addition the bus speed
can be set in the devicetree and that speed will be applied when the
device is initialized. If not provided the default speed is set to
I2C_SPEED_FAST.
This was tested with the google/chell mainboard by reading and writing
from the trackpad and codec devices during both verstage and ramstage.
Change-Id: Ia0270adfaf2843a3be4e00c732c85401a3401ef5
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/15105
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
|
|
Move the existing I2C voltage configuration variable into a new
structure that is equivalent, similar to how USB ports are configured.
This is to make room for additional I2C configuration options like
bus speed and whether to enable the bus in early boot which are coming
in a subsequent commit.
The affected mainboards are updated in this commit so it will build.
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Change-Id: Id2dea3df93e49000d60ddc66eb35d06cca6dd47e
Reviewed-on: https://review.coreboot.org/15104
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Add the voltage tolerance GPIO attribute for configuring I2C/I2S buses
that are at 1.8V. This is currently done by passing in a value to FSP
but it is needed earlier than FSP if the I2C bus is used in verstage.
This does not remove the need for the FSP input parameter, that is
still required so FSP doesn't disable what has been set in coreboot.
The mainboards that are affected are updated in this commit.
This was tested by exercising I2C transactions to the 1.8V codec while
in verstage on the google/chell mainboard.
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Change-Id: I93d22c2e3bc0617c87f03c37a8746e22a112cc9c
Reviewed-on: https://review.coreboot.org/15103
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
|
|
Add a function similar to broadwell to set the PRR for a region of
flash and protect it from writes. This is used to secure the MRC
cache region if the SPI is write protected.
BUG=chrome-os-partner:54003
BRANCH=glados
TEST=boot on chell, verify PRR register is set and that the
MRC cache region cannot be written if the SPI is write protected.
Change-Id: I925ec9ce186f7adac327bca9c96255325b7f54ec
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Original-Commit-Id: abb6f645f5ceef3f52bb7afd2632212ea916ff8d
Original-Change-Id: I2f90556a217b35b7c93645e41a1fcfe8070c53da
Original-Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/349274
Original-Reviewed-by: Shawn N <shawnn@chromium.org>
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Original-Tested-by: Shawn N <shawnn@chromium.org>
Reviewed-on: https://review.coreboot.org/15102
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Leroy P Leahy <leroy.p.leahy@intel.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Correct the spelling of *firmware* in a comment.
Change-Id: I44bcd95f754ff839d582dc2150e1883a6315da9e
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: https://review.coreboot.org/15078
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Add a PCI driver for the skylake SD card device and have it generate
an entry in the SSDT for the card detect GPIO if it is provided by the
mainboard in devicetree.
This sets up a card detect GPIO configuration that will trigger an
interrupt on both edges with a 100ms debounce timeout and can wake the
SD controller from D3 state.
The GpioInt() entry is bound to the "cd-gpio" device property which will
be consumed by the kernel driver.
The resulting ACPI output in the SSDT will be combined with the SDXC
device declaration in the DSDT.
Example:
Scope (\_SB.PCI0.SDXC)
{
Name (_CRS, ResourceTemplate () {
GpioInt (Edge, ActiveBoth, SharedAndWake, PullNone, 10000,
"\\_SB.PCI0.GPIO", 0, ResourceConsumer) { 35 }
})
Name (_DSD, Package () {
ToUUID ("daffd814-6eba-4d8c-8a91-bc9bbf4aa301"),
Package () {
Package () { "cd-gpio", Package () { \_SB.PCI0.SDXC, 0, 0, 1 } }
}
})
}
Change-Id: Ie4c1bfadd962cf55a987edb9ef86e92174205770
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/14995
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Minor cleanups in pci_devs.h for indentation and newlines to be
consistent throughout the file.
Change-Id: I522df141a6b33d918cfb3de1b9019c0c4a73e3e5
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/14994
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Add the Audio DSP device for skylake as a PCI driver with a static
scan_bus handler so generic devices can be declared under it.
This is for devices like the Maxim 98357A which is connected on the
I2S bus for data but has no control channel bus and instead just has
a GPIO for channel selection and power down control and needs to
describe that GPIO connection to the OS via ACPI.
Change-Id: Iae02132ff9c510562483108ab280323f78873afd
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/14993
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Add the I2C devices to skylake with the scan_bus handler for SMBUS
devices so that I2C-based devices can be declared in devicetree.cb
and get initialized properly during ramstage.
This does not yet provide the I2C driver, but it allows for devices
that are declared in devicetree.cb to provide ACPI tables to the OS.
Change-Id: I9dfe4a06a8b0bc549a2b0e2d7c033c895188ba30
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/14992
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Add the GPE header file to skylake chip.h so the SOC-defined macros
for the various GPE values can be used in devicetree directly.
For example:
chip drivers/i2c/touchpad
register "wake" = "GPE0_DW0_05"
device i2c 15.0 on end
end
Change-Id: Ic322108561b34aa34a24a4daba6ba7a4f7a3f9a4
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/14991
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Add a handler for the Intel Skylake SOC to return the ACPI path for
GPIOs. Since all GPIOs are handled by the same controller they all
have the same ACPI path and this is a simple handler that just returns
a pointer to the GPIO device that is defined in the DSDT.
Change-Id: I24ff3a6f2479d9e7eeace65d49e2f6c2e070f3e9
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/14843
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
|
|
Add a global ACPI device name handler for the Skylake SOC that will
translate skylake device paths into an ACPI path that matches the
device objects delcared in the DSDT at soc/intel/skylake/acpi/*.
The skylake implementation uses a global acpi_name handler for the
SOC and it is not necessary to add a function to every device.
This function is used by device drivers calling acpi_device_name()
and acpi_device_path() to generate ACPI AML in the SSDT.
Change-Id: I31cecf7905a51224e7bfc40c6c4ad2487f039097
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/14841
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
|
|
Allow the platform to override the input clock for the UART by
implementing the routine uart_platform_refclk and setting the Kconfig
value UART_OVERRIDE_REFCLK. Provide a default uart_platform_refclk
routine which is disabled when UART_OVERRIDE_REFCLK is selected. This
works around ROMCC not supporting weak routines.
Testing on Galileo:
* Edit the src/mainboard/intel/galileo/Makefile.inc file:
* Add "select ADD_FSP_PDAT_FILE"
* Add "select ADD_FSP_RAW_BIN"
* Add "select ADD_RMU_FILE"
* Place the FSP.bin file in the location specified by CONFIG_FSP_FILE
* Place the pdat.bin files in the location specified by
CONFIG_FSP_PDAT_FILE
* Place the rmu.bin file in the location specified by CONFIG_RMU_FILE
* Build EDK2 CorebootPayloadPkg/CorebootPayloadPkgIa32.dsc to generate
UEFIPAYLOAD.fd
* Testing is successful when CorebootPayloadPkg is able to properly
initialize the serial port without using built-in values.
Change-Id: If4afc45a828e5ba935fecb6d95b239625e912d14
Signed-off-by: Lee Leahy <leroy.p.leahy@intel.com>
Reviewed-on: https://review.coreboot.org/14612
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Command List:
Send command for PS4 exit fails
BUG=chrome-os-partner:52355
BRANCH=glados
TEST=Build and boot lars and verify no hang during active idle
CQ-DEPEND=CL:*257305
Change-Id: I9ffae71b1a38433ffc48ee7be7e2a13e69ad5b87
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 96f00e2d153f92339c378ce256eb7ce6824e3368
Original-Change-Id: I320ae154f3f7145811b57258ddb61b3beb584273
Original-Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/341330
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/14688
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Output a few more status bits from HFS/HFS2 and add
some interesting bits from HFS3.
BUG=chrome-os-partner:52662
BRANCH=glados
TEST=boot on chell and verify ME status output
Change-Id: I989b680f203678dbe28559e858faf8b4e0837481
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 8ea34ab019da3fff965102bcef5158ddcc154728
Original-Change-Id: Iff977c8d85b4d4dfa00b5b19bc29d11813a99b9f
Original-Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/340390
Original-Reviewed-by: Aaron Durbin <adurbin@google.com>
Reviewed-on: https://review.coreboot.org/14687
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Duncan Laurie <dlaurie@google.com>
|
|
The XIP_ROM_SIZE Kconfig variable isn't used for these chipsets.
Therefore, indicate as such so that romstage can be placed in
cbfs less rigidly.
Change-Id: If5cae10b90e05029df56c282e8adf37fa0102955
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/14626
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
There used to be a need for an empty smm_init() function
because initialize_cpus() called it even though nothing
called initialize_cpus(). However, garbage collection at
link time is implemented so there's no reason to provide an
empty function to satisfy a symbol that is completely culled
during link. Remove it.
Change-Id: Ic13c85f1d3d57e38e7132e4289a98a95829f765a
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/14605
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
In order to reduce duplication of code use the common MP and SMM
initialization flow.
Change-Id: I5c4674ed258922b6616d75f070df976ef9fad209
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/14597
Tested-by: build bot (Jenkins)
Reviewed-by: Leroy P Leahy <leroy.p.leahy@intel.com>
Reviewed-by: Duncan Laurie <dlaurie@google.com>
|
|
Unconditionally provide the backup default SMM area API. There's no
reason to guard the symbols behind anything since linker garbage
collection is implemented. A board or chipset is free to use the
code or not without needing to select an option.
Change-Id: I14cf1318136a17f48ba5ae119507918190e25387
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/14561
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
The BSP and AP callback declarations both had an optional argument
that could be passed. In practice that functionality was never used
so drop it.
Change-Id: I47fa814a593b6c2ee164c88d255178d3fb71e8ce
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/14556
Tested-by: build bot (Jenkins)
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Leroy P Leahy <leroy.p.leahy@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Update all of the license headers to make sure they are compliant
with coreboot's license header policy.
Change-Id: I151d058615290e528d9d1738c17804f6b9cc8dce
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/14321
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
This patch would enable PROCHOT feature in skylake. Asserting
PROCHOT line would throttle the GPU/CPU.
BUG=chrome-os-partner:51142
BRANCH=glados
TEST=manually tested on lars. asserting PROCTHOT by EC
reduces FSP in fish-tank from approx 40 to 20. (50 fish setting),
also CPU freq. drops to from 1600000 to 400000
Change-Id: I8fc0c015ea2c26d20bbbfc619f720f231d540feb
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 1b88b1f183df9c7362d7e58acb0a1fa0b076d56e
Original-Change-Id: Ida8636efc3d8da56ebd3931144d31ab1b88fe806
Original-Signed-off-by: Pratik Prajapati <pratikkumar.v.prajapati@intel.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/331690
Original-Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Original-(cherry picked from commit d091a999c3827179182b62a1274a9b3581f7f006)
Original-Reviewed-on: https://chromium-review.googlesource.com/333073
Original-Commit-Ready: Pratikkumar V Prajapati <pratikkumar.v.prajapati@intel.com>
Original-Tested-by: Pratikkumar V Prajapati <pratikkumar.v.prajapati@intel.com>
Original-Reviewed-by: Pratikkumar V Prajapati <pratikkumar.v.prajapati@intel.com>
Reviewed-on: https://review.coreboot.org/14120
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Skip logging a wake source when just resetting without coming from
S3 or S5 state. This will prevent the occasional spurious event
like PCI PME from showing up in the event log.
BUG=chrome-os-partner:40635
BRANCH=glados
TEST=run warm reboot teset on chell and ensure no wake source is logged
Change-Id: If739034dc9022b37c90b9cc849a00c604383e70f
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: e7b5cc91adc3ed10df7cebd758cf8144216b9890
Original-Change-Id: I16f4f98df8c70fd25986a8b3644334c7209fd083
Original-Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/329846
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/331173
Original-Commit-Ready: Patrick Georgi <pgeorgi@chromium.org>
Original-Tested-by: Patrick Georgi <pgeorgi@chromium.org>
Reviewed-on: https://review.coreboot.org/13991
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
In order to save more power by shutting down clocks add the
ability to optionally clock gate the 8254 programmable interrupt
timer. When doing this the platforms lose their "PC"-ness which
certain payloads and OSes rely on such as SeaBIOS.
BUG=chrome-os-partner:50214
BRANCH=glados
TEST=Enabled option on chell. Noted the bit is set upon booting.
Change-Id: I01f9d177bbde417d1efec2e16656a07dcebccbde
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 662575aa6a63656dedfa0ce1f202f5fac0205477
Original-Change-Id: Ib4a613cf1c28fc96c36fa2987c4b58a05beab178
Original-Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/329411
Original-Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/331171
Original-Commit-Ready: Patrick Georgi <pgeorgi@chromium.org>
Original-Tested-by: Patrick Georgi <pgeorgi@chromium.org>
Reviewed-on: https://review.coreboot.org/13985
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Adding an option to enable VR specific mailbox command.
When set, an extra VR mailbox command specifically for
the MPS IMPV8 VR will be sent.
BUG=chrome-os-partner:48511
BRANCH=None
TEST=Verified on glados, clean S0ix entry and exit.
IMVP8 power is also pretty low
Change-Id: Ia5a23cbb1eca8b463eb7c7c279b74635f1d6b9f7
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: c90a799b51fe35bf184dca6ffce59c89a60f9917
Original-Change-Id: Iffd3fbcb9a15611eefc942529e6cdafba859fb2e
Original-Signed-off-by: Robbie Zhang <robbie.zhang@intel.com>
Original-Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/329393
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/13982
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
For all the chipsets which were performing the following sequence:
x86_setup_fixed_mtrrs();
x86_setup_var_mtrrs(cpuid_eax(0x80000008) & 0xff, 2);
Replace that with x86_setup_mtrrs_with_detect() since it is equivalent.
Change-Id: I9f362dbf38942d675f615d22b9e5770ce65e5a08
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/13936
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Andrey Petrov <andrey.petrov@intel.com>
|
|
Add a country identifier field to NVS and populate it with the
call to wifi_regulatory_domain() which will (by default) do a
lookup for the 'region' identifier in VPD on a Chrome OS device.
BUG=chrome-os-partner:50516
BRANCH=glados
TEST=build and boot on chell
Change-Id: Ie7531848e620095732772c22156a85b7f8a6df5c
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Original-Commit-Id: dafdb3760a0302e3effdc0e83977c1bfd5c9d3b2
Original-Change-Id: Ic83ab008045a469d0e0756f7e4d42f1b3894c529
Original-Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/329295
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/13839
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Intel Speed Shift Technology is a new mechanism that replaces
Legacy P-state. ISST allows OS hints about energy/performance
preference. H/W performs the actual P-state control (autonomous)
1. Optimization frequency seclection for low residency workloads,
no longer a static knee point.
2. Optimized frequency selection for best energy to performance
trade offs.
3. Kick down frequency (from idle) fpr best responsiveness while
taking energy consumption init account.
Coreboot's responsiblity is to configure MSR 0x1AA ISST_EN bits
which will reflect in CPUID.06h:EAX[Bit 7] that driver checkes
and enable HWP accordingly.
BUG=chrome-os-partner:47517
BRANCH=None
TEST=Booted kunimitsu and verify HWP getting enabled/disabled
using Intel P-state driver.
Change-Id: I91722aa1077f4ef6c8620b103be3e29cfcd974e5
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Original-Commit-Id: aa7d004cb2e19047e4434e3e2544cf69393ce28f
Original-Change-Id: Ie617da337babde7f196a7af712263e37f7eed56f
Original-Signed-off-by: Robbie Zhang <robbie.zhang@intel.com>
Original-Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/313107
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Original-Reviewed-by: Wenkai Du <wenkai.du@intel.com>
Reviewed-on: https://review.coreboot.org/13835
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
The FBC hardware for skylake does not have access to the bios_reserved
range so it always assumes 8MB is used and so the kernel will
therefore need to avoid using the last 8MB of the stolen window.
With the default stolen size of 32MB(-8MB) there is not enough space
for FBC to work with a high resolution panel.
Kernel reference:
http://git.kernel.org/cgit/linux/kernel/git/torvalds/linux.git/commit/?id=a9da512b3ed73045253afd778e40d4298f42905b
BUG=chrome-os-partner:50396
BRANCH=glados
TEST=build and boot on chell DVT
Change-Id: I3049d7d9e7c551aad5b8fd1630d5fbd88ccb2692
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Original-Commit-Id: fff1f4b35e23e77cdc72c5bcc290f199494cdbbb
Original-Change-Id: If468cca5759a320f3cd2d7eb09f4bcc0117b24cb
Original-Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/328813
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/13833
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Once we lock down the SPI BAR we need to tell SMM to re-init its
SPI driver or it will be unable to write ELOG events via SMI.
This SMI is also sent at the end of depthcharge so there was just
a window where SMI events could get lost.
BUG=chrome-os-partner:50076
BRANCH=glados
TEST=enable DEBUG_SMI, boot to dev screen, press power button and
see elog events get added without without transaction errors.
Change-Id: I1f14717b5e7f29c158dde8fd308bdbfb67eba41a
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 60ca24c760c70e2ebe5f3e68f95d3ffdba0fef9e
Original-Change-Id: I4e323249f00954e290a6a30f515e34632681bfdd
Original-Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/326861
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/13697
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
The PCH does not set PM1_STS[WAK_STS] bit when waking from a
G3 state, which is triggered by hibernate now on chell when we
do a PMIC shutdown. This means the checks for S5 wake are not
done and instead it is logged as a wake from S0.
BUG=chrome-os-partner:50076
BRANCH=glados
TEST=pass firmware_EventLog test on chell
Change-Id: I3ca05a4824df3401150a63d4b6555f759de40087
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: de6c9bac447edd06568193f990f1f4e278576783
Original-Change-Id: I4472498468d620fe69f2b68710e818a4ad287382
Original-Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/326888
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/13696
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
This change will allow the kernel to use 4-lane eDP connections
if the GOP driver does not execute and set this bit. If GOP
has executed (everyone but Chrome OS verified mode) the link will
already be up and this will do nothing.
BUG=chrome-os-partner:50197
BRANCH=glados
TEST=boot on chell and ensure 4
Change-Id: I9e2328b00db84f26b9bd03220b8ac0bd5f64cfbf
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: cff83e18ce9936c8d507f93c8443b7056c62e844
Original-Change-Id: I3f1e5d78b91eb0e4a23fcc196aff0edadc252a0c
Original-Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/327251
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/13690
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
This method creates a named object and should be serialized to avoid
a compiler warning from recent iasl releases.
BUG=chrome-os-partner:40635
BRANCH=glados
TEST=emerge-chell coreboot with no iasl warnings
Change-Id: If54df4eca8849a8d278816712164b30a775a41ca
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 9aa8c5627276be08bf0dc3d0f4b9b7bd3f40c227
Original-Change-Id: Ieb05525503bf61c9922677484aba5479856a3f35
Original-Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/326843
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/13689
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
This patch generalizes the approach previously used for ARM32
TTB_SUBTABLES to "auto-detect" whether a certain region was defined in
memlayout.ld. This allows us to get rid of the explicit Kconfig for the
TIMESTAMP region, reducing configuration redundancy and avoiding
confusion when setting up future boards.
(Removing armv4/bootblock_simple.c because it references this Kconfig
and it is a dead file that I just forgot to remove in CL:12076.)
BRANCH=None
BUG=None
TEST=Booted Oak and confirmed that all pre-RAM timestamps are still
there. Built Nyan and Falco.
Change-Id: I557a4b263018511d17baa4177963130a97ea310a
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/13652
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
We want the question for CBFS size to be next to the rom size in the
mainboard directory, but that doesn't seem to work for how people
want to set the defaults. Instead of having the list of exceptions
to the size, just set the defaults at the end of kconfig.
- Move the defaults for chipsets not setting HAVE_INTEL_FIRMWARE into
the chipset Kconfigs (gm45, nehalem, sandybridge, x4x)
- Override the default for HAVE_INTEL_FIRMWARE on skylake.
- Move the HAVE_INTEL_FIRMWARE default setting into the firmware
Kconfig file
- Move the location of the default CBFS_SIZE=ROM_SIZE to the end of
the top level kconfig file, while leaving the question where it is.
Test=rebuild Kconfig files before and after the change, verify that
they are how they were intended to be.
Note: the Skylake boards actually changed value, because they were
picking up the 0x100000 from HAVE_INTEL_FIRMWARE instead of the
0x200000 desired. This was due to the SOC_INTEL_SKYLAKE being after
the HAVE_INTEL_FIRMWARE default. Affected boards were:
Google chell, glados, & lars and Intel kunimitsu.
Change-Id: I2963a7a7eab037955558d401f5573533674a664f
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/13645
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Unused PINS will be controlled by GPIO controller (PMODE = GPIO) and
GPIO TX/RX will be disabled.
BUG=none
BRANCH=none
TEST=Build and boot lars
Change-Id: I3a6fcd2f3462e8e0d1273aa80b1599b76b160825
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 889bfd66dbc918e9fb0ba1b95b63fd7a3bf180d9
Original-Change-Id: I3bf4aa8599255e5382d99810b4c83b4c97c648b6
Original-Signed-off-by: David Wu <David_Wu@quantatw.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/319964
Original-Commit-Ready: David Wu <david_wu@quantatw.com>
Original-Tested-by: David Wu <david_wu@quantatw.com>
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Original-Reviewed-by: Rajneesh Bhardwaj <rajneesh.bhardwaj@intel.com>
Original-Reviewed-by: Pratikkumar V Prajapati <pratikkumar.v.prajapati@intel.com>
Reviewed-on: https://review.coreboot.org/13628
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
This patch added nhlt_soc_serialize_oem_overrides and
nhlt_serilalize_oem_overrides to be able to override oem_id and
oem_table_id.board file can pass specific string by calling
nhlt_soc_serialize_oem_overrides
kernel use these two fields to construct a topology binary name
if the designate file is not found a default dfw_sst.bin will be used
it is optional.
BUG=chrome-os-partner:49570
BRANCH=glados
TEST=Build & Booted kunimitsu board. Verified that kernel
can read new strings.
Change-Id: I00b64fb8bb63de601d3116e0b8941057c1efa230
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 374ce08b2d8a2f4e5dd7f51eacb505dbb77fd171
Original-Change-Id: I03623c8ac81efb5a5ea3ec9c6cd604d2e9294022
Original-Signed-off-by: Fang, Yang A <yang.a.fang@intel.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/322860
Original-Commit-Ready: Yang Fang <yang.a.fang@intel.com>
Original-Tested-by: Yang Fang <yang.a.fang@intel.com>
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/13602
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
The VBNV region size is determined by vboot and is not really
configurable. Only the CMOS implementation defined this config
variable so switch it to use VBNV_BLOCK_SIZE defined by vboot
in vbnv_layout.h instead.
This requires updating the broadwell/skylake cmos reset functions
to use the right constant.
BUG=chrome-os-partner:47915
BRANCH=glados
TEST=manually tested on chell
Change-Id: I45e3efc2a22efcb1470bbbefbdae4eda33fc6c96
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: e2b803ff3ac30ab22d65d1e62aca623730999a1d
Original-Change-Id: I4896a1a5b7889d77ad00c4c8f285d184c4218e17
Original-Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/324520
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/13598
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Keeping ACPI PM timer alive prevents XTAL OSC shutdown in S0ix
which has a power impact.
Based on a DT variable, this patch disables the ACPI PM timer
late in the boot sequence - disabling earlier will lead to a hang
since the FSP boot flow needs this timer. This also hides the ACPI PM
timer from the OS by removing from FADT table. Once the ACPI PM timer
is disabled, TCO gets switched off as well.
BRANCH=none
BUG=chrome-os-partner:48646
TEST=Build for skylake board with the PmTimerDisabled policy in
devicetree set to 1.
iotools mmio_read32 0xfe0000fc should return 0x2.
cat /sys/devices/system/clocksource/clocksource0/available_clocksource
should list only "tsc hpet". acpi_pm should be removed from this list.
Change-Id: Icfdc51bc33b5190a55196d67e18afdaaa2f9b310
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 18bcb8a434b029295e1f1cc925e2b47e79254583
Original-Change-Id: Ifebe8bb5a7978339e07e4e12e174b9b978135467
Original-Signed-off-by: Archana Patni <archana.patni@intel.com>
Original-Signed-off-by: Subramony Sesha <subramony.sesha@intel.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/319361
Original-Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/13588
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
The setting of the SPI controller BAR was conditional
on the nominal frequency being set. Therefore, that doesn't
mean the SPI BAR is set on all boots. Move the setting of
the BAR in the southbridge_bootblock_init() which is called
prioer to cpu_bootblock_init().
BUG=chrome-os-partner:44827
BRANCH=None
TEST=Confirmed spibar is always set on glados.
Change-Id: Ia58447d70f5e39a4336d4d08593f143332de833a
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 56fff7c25c2eb0ccd90e08f71c064b83c66640f8
Original-Change-Id: I1e0cff783f4b072b80589a3a84703a262b86be3a
Original-Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/319461
Original-Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/13587
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
In order to not reboot loop in the face of failed vboot verification
on resume set the PM1 control register to indicate S5. After the
subsequent cold reset the PM1 control register will indicate S5
as it should.
BUG=chrome-os-partner:46049
BRANCH=glados
TEST=On chell injected failed vboot verification. Ensured a reboot
loop doesn't ensue.
Change-Id: Ie5e9e3f6441a217a5e02b4d78aaf21f8249b8a43
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: a63b57d7bc59bcaf5518f7cc4afccd3d5da6df1c
Original-Change-Id: I5e467854bf065a138bd46e476a7e7088f51454ca
Original-Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/323504
Original-Reviewed-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/13579
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
To allow skylake platforms to run with verified memory init
code the chipset needs to implement vboot_platform_is_resuming()
so that the vboot code can make proper decisions.
BUG=chrome-os-partner:46049
BRANCH=glados
TEST=Suspended and resumed on chell. Also, tested with an EC build
which returns a bad hash to ensure that is properly caught.
Change-Id: I508a339c07dcc9e7c56a0df4201660827b3ae07a
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: a3e11789339bcd8fc8fc99b704c6a1110acf5302
Original-Change-Id: I40264019eb28e85795258112c720056a6a3fc523
Original-Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/323503
Original-Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/13578
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|