Age | Commit message (Collapse) | Author |
|
Instead of writing out '__attribute__((weak))' use a shorter form.
Change-Id: If418a1d55052780077febd2d8f2089021f414b91
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/25767
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
|
|
The ACPI MCFG table is generated with a static end bus number of 255,
which expects that the reserved range in E820 is 256MB. However the
actual MCFG range is configurable with Kconfig, so these two values
may not match when the OS tries to determine the range:
PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
PCI: MMCONFIG 0000 [bus 00-3f] at [mem 0xe0000000-0xe3ffffff] (base 0xe0000000) (size reduced!)
acpi PNP0A08:00: [Firmware Info]: MMCONFIG for domain 0000 [bus 00-3f] only partially covers this bridge
Instead of forcing the end bus number to be 255 use the Kconfig value
to set it based on the current configuration.
Tested on a fizz device to ensure that the kernel no longer complains:
PCI: MMCONFIG for domain 0000 [bus 00-3f] at [mem 0xe0000000-0xe3ffffff] (base 0xe0000000)
Change-Id: I999ea9b72b9deba5f27dd692faa0408427a0bf89
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/24974
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable the ACPI DBG2 table generation for Intel boards. This is
a Microsoft defined ACPI extension that allows an OS to know what
the debug port is on a system when it is not enabled by the
firmware, so it does not show up in the coreboot tables and
cannot be easily found by a payload.
broadwell: Use byte access device, set up only when enabled since
it relies on the port being put in byte access mode and using
this serial port for debug was not standard in this generation.
skylake: Enable for the configured debug port. Skylake uses
intelblocks for UART but not ACPI.
common: Enable for the configured debug port. This affects
apollolake and cannonlake.
Tested by compiling for apollolake/broadwell, tested by reading
the DBG2 ACPI table on kabylake board and using IASL to dump:
[000h 0000 4] Signature : "DBG2"
[004h 0004 4] Table Length : 00000061
[008h 0008 1] Revision : 00
[009h 0009 1] Checksum : 3B
[00Ah 0010 6] Oem ID : "CORE "
[010h 0016 8] Oem Table ID : "COREBOOT"
[018h 0024 4] Oem Revision : 00000000
[01Ch 0028 4] Asl Compiler ID : "CORE"
[020h 0032 4] Asl Compiler Revision : 00000000
[024h 0036 4] Info Offset : 0000002C
[028h 0040 4] Info Count : 00000001
[02Ch 0044 1] Revision : 00
[02Dh 0045 2] Length : 0035
[02Fh 0047 1] Register Count : 01
[030h 0048 2] Namepath Length : 000F
[032h 0050 2] Namepath Offset : 0026
[034h 0052 2] OEM Data Length : 0000
[036h 0054 2] OEM Data Offset : 0000
[038h 0056 2] Port Type : 8000
[03Ah 0058 2] Port Subtype : 0000
[03Ch 0060 2] Reserved : 0000
[03Eh 0062 2] Base Address Offset : 0016
[040h 0064 2] Address Size Offset : 0022
[042h 0066 12] Base Address Register : [Generic Address Structure]
[042h 0066 1] Space ID : 00 [SystemMemory]
[043h 0067 1] Bit Width : 00
[044h 0068 1] Bit Offset : 00
[045h 0069 1] Encoded Access Width : 03 [DWord Access:32]
[046h 0070 8] Address : 00000000FE034000
[04Eh 0078 4] Address Size : 00001000
[052h 0082 15] Namepath : "\_SB.PCI0.UAR2"
Change-Id: If34a3d2252896e0b0f762136760ab981afc12a2f
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/22453
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This patch adds the common acpi code.ACPI code is very similar
accross different intel chipsets.This patch is an effort to
move those code in common place so that it can be shared accross
different intel platforms instead of duplicating for each platform.
We are removing the common acpi files in src/soc/intel/common.
This removes the acpi.c file which was previously in
src/soc/common/acpi. The config for common acpi is
SOC_INTEL_COMMON_BLOCK_ACPI which can be defined in SOC's
Kconfig file in order to use the common ACPI code. This patch also
includes the changes in APL platform to use the common ACPI block.
TEST= Tested the patch as below:
1.Builds and system boots up with the patch.
2.Check all the ACPI tables are present in
/sys/firmware/acpi/tables
3.Check SCI's are properly working as we are
modifying the function to override madt.
4.Extract acpi tables like DSDT,APIC, FACP, FACS
and decompile the by iasl and compare with good
known tables.
5.Execute the extracted tables in aciexec to check
acpi methods are working properly.
Change-Id: Ib6eb6fd5366e6e28fd81bc22d050b0efa05a2e5d
Signed-off-by: Shaunak Saha <shaunak.saha@intel.com>
Reviewed-on: https://review.coreboot.org/20630
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
|