Age | Commit message (Collapse) | Author |
|
Ignore integrated GBE controller LTR setting to make it wake up from
s0ix with 10/100M cable attached.
BUG=b:122435844
TEST= Test on sarien platorm, after the changes sytem can wake by WOL,
and also checked SLP_S0 residency can increase with 10/100M cable
and battery connected.
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: Iec7dd197b8a456751f8e4dcb19e3e153f5888613
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31888
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
The following is the FSP logic: as long as the Cpu Ratio input in
coreboot is different with CpuStrapSet, system will force to follow
input from coreboot. But CpuStrapsetting is floating, it will be 0
from the first cold boot before memory training and set to 0x1c (or
max CPU ratio for the installed CPU) after first memory training.
The previous fix was attempting to ensure settings were cleared
when FSP was called in recovery mode, but only when coming from S5
which caused issues if recovery mode is requested by the OS and
is only followed by a warm reset.
BUG=b:129412691
TEST=Boot up sarien platform and force recovery, check there's no reset
in the path of recovery.
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: I959188be46343bc6f2cb3cc149097b4d449802aa
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32089
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
For systems that integrate GbE controllers, following parameters should be configured:
SlpS0WithGbeSupport: enable PchPmSlpS0VmRuntimeControl: disable,
PchPmSlpS0Vm070VSupport: disable, PchPmSlpS0Vm075VSupport: disable.
TEST=boot on any GbE supported WHL platform
Change-Id: I02aaf0b77b8fc1555a3a424c02acfada21707d0e
Signed-off-by: Krzysztof Sywula <krzysztof.m.sywula@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32026
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
The prev_sleep_state value was showing 5 even after warm reboot, once the
SUS_PWR_FLR bit is being set. This bit was not being cleared.
Hence clearing the PMCON status bits.
BUG=b:128482282
BRANCH=None
TEST=In cbmem logs, check for value of “prev_sleep_state” using command
cbmem –c | grep “prev_sleep_state”
For cold reboot, "prev_sleep_state 5"
For warm reboot, "prev_sleep_state 0"
Change-Id: If9863d52ed3c61b6a160df53f023b0787eaaed68
Signed-off-by: Krishna Prasad Bhat <krishna.p.bhat.d@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31902
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
|
|
This patch ensures to make use of common MP Init Kconfig to
choose desire method to peform MP initialization for platform.
Change-Id: I4ee51276026748e8daf154f89e57095e8fe50280
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/30289
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
This change enables user to shutdown the system by shortly pressing
power button (<10sec) before OS is loaded. Main use case is shutdown
from recovery/broken screen.
BUG=N/A
TEST=Boot up into recovery screen on Sarien platform, press power button
once, and system should shutdown immediatelly.
Change-Id: I7655daf65ff058df7d9bad4567f74b4f4007acb4
Signed-off-by: Krzysztof Sywula <krzysztof.m.sywula@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31894
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Assign the FSP UPDs for HPD and DDC of DDI ports. FSP assumes that all
DDI ports are enabled and hence configures the HPD and CLK for DDI ports.
This patch initializes only the required UPDs to enable display ports.
BUG=b:123907904
TEST=DP devices working correctly.
Change-Id: Ic0c172cd3d087fc8f49b01ab23feffdababf7166
Signed-off-by: Krishna Prasad Bhat <krishna.p.bhat.d@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31520
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Drop 'include <string.h>' when it is not used and
add it when it is missing.
Also extra lines removed, or added just before local includes.
Change-Id: Iccac4dbaa2dd4144fc347af36ecfc9747da3de20
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31966
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Commit 41483c9 (soc/intel/cannonlake: Add required FSP UPD changes for
CML) changed the enum values for PCH_SERIAL_IO_MODE so that 0 is
invalid and valid values start from 1. However, get_param_value was
not updated to correctly subtract 1 before returning any value. This
change adds a macro PCH_SERIAL_IO_INDEX to apply the subtract 1
operation on any value that get_param_value needs to return.
BUG=b:128946016
TEST=Verified that hatch boots successfully.
Change-Id: I4e32fcd1efe4a535251f0ec58662a2dc5f70e8b0
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31974
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
coreboot have an option to use legacy UART or LPSS UART. FSP will use the
UART initialized by coreboot and we can choose an option to skip Uart
initialization by FSP.
For this, we need to pass correct debug interface flag to FSP through
which FSP will know which UART port to use. If we don't pass correct
interface information, FSP may try to dump logs on that port and it may
slow down the system.
BUG=none
BRANCH=none
TEST=Compile and boot with coreboot. Check FSP and coreboot logs are
coming on serial port.
Change-Id: I1ebb20c93e2c15ec085538509099de72bc9dd62c
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31884
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This patch adds required FSP UPD changes for CometLake SoC.
Also this patch tries to create common parse logic for CometLake as
well as cannonlake SOC.
We parse device tree parameters for PCI devices and fill values in FSP
UPDs. We fill UPDs based on pci device config as well as SerialIoDev
config of devicetree.
For PCI devices, if PCI device is disabled from devicetree, we'll assign
disable value to FSP UPD.
In case devicetree doesn't fill this parameter or value is invalid in
SerialIoDev config, default mode will be set to PCI.
In case of valid value, we'll fill the same value into FSP UPD.
BUG=none
BRANCH=none
TEST=check if CML board boots and proper UPD values are filled.
Change-Id: Ib92b660409ab01d70358042b2ed29b8bf9cab26d
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31284
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: V Sowmya <v.sowmya@intel.com>
|
|
Change-Id: Ie7afe77053a21bcf6a1bf314570f897d1791a620
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31921
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
CNL PCH has PWR_FLR, SUS_PWR_FLR and HOST_RST_STS bits in GEN_PMCON_A
and so this change updates the check for these bits to use GEN_PMCON_A
instead of GEN_PMCON_B.
BUG=b:128482282
TEST=Verified that prev_sleep_state is reported correctly when booting
from S5.
Change-Id: I75780a004ded8f282ffb3feb0cdc76233ebfd4f2
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31908
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
In order to support mainboards that do not store DRAM part number in
the traditional way i.e. within the CBFS SPD for soldered memory, this
change provides a runtime callback to allow mainboards to provide DRAM
part number from a custom location e.g. external EEPROM on hatch.
For other boards it should be a NOP since the weak implementation of
mainboard_get_dram_part_num does nothing.
BUG=b:127609572
Change-Id: I9b2d4c33fc378b9a24b111971ec2bfdb5f8d57d0
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31850
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Use <arch/acpi.h> when appropriate.
Change-Id: I05a28d2c15565c21407101e611ee1984c5411ff0
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31781
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
This patch is a raw application of
find src/ -type f | xargs sed -i -e 's/IS_ENABLED\s*(CONFIG_/CONFIG(/g'
Change-Id: I6262d6d5c23cabe23c242b4f38d446b74fe16b88
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31774
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
This patch adds support for logging wake source information in gsmi
callbacks. With this change, all the elog logging infrastructure can
be used for S0ix as well as S3 on cannonlake.
BUG=b:124131938
BRANCH=none
TEST=Verified that the wake events are logged during the S0ix resume:
6 | 2019-03-04 17:03:13 | S0ix Enter
7 | 2019-03-04 17:03:17 | S0ix Exit
8 | 2019-03-04 17:03:17 | Wake Source | RTC Alarm | 0
9 | 2019-03-04 17:03:55 | S0ix Enter
10 | 2019-03-04 17:03:56 | S0ix Exit
11 | 2019-03-04 17:03:56 | Wake Source | GPE # | 21
12 | 2019-03-04 17:04:36 | S0ix Enter
13 | 2019-03-04 17:04:45 | S0ix Exit
14 | 2019-03-04 17:04:45 | Wake Source | GPE # | 112
15 | 2019-03-04 17:05:01 | S0ix Enter
16 | 2019-03-04 17:05:09 | S0ix Exit
17 | 2019-03-04 17:05:09 | Wake Source | Power Button | 0
Change-Id: Id627843e22c2524dfa94395b780cf2134f386137
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31788
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This change moves soc_fill_power_state and soc_prev_sleep_state to
pmutil.c. It allows the functions to be used across romstage and smm.
BUG=b:124131938
BRANCH=none
TEST=none
Change-Id: If24c3feeb77f4fb692ef0bf38d537b2b54de3c36
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/31787
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
MMIO operations are arch-agnostic so the include
path should not be arch/.
Change-Id: I0fd70f5aeca02e98e96b980c3aca0819f5c44b98
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/31691
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I91158452680586ac676ea11c8589062880a31f91
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/31692
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Move common definitions for PCH H and LP to a common header.
Change-Id: If47692ecb05134db1ee6c0fb10125d6a1b67f127
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/c/31621
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Create the ISH ACPI device so we can hang fields off of a _DSD table.
Since this is also a PCI device that has run time probing, we can always
emit the ACPI device and let the device tree turn the device on or off.
BRANCH=none
BUG=b:122722008
TEST=verify that _DSD table gets publish under ISH device in kernel ACPI
tables. Also verified that device is still turned off if device tree for
ISH is off.
Change-Id: Ic0231f1ac637fea0e251eb3ac84f0fd8d64c12b2
Signed-off-by: Jett Rink <jettrink@chromium.org>
Reviewed-on: https://review.coreboot.org/c/31681
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The following remarks show up during cannonlake based platform coreboot
build:
dsdt.asl 55: Offset (0x00),
Remark 2158 - ^ Unnecessary/redundant use of Offset operator
dsdt.asl 136: Offset (0xa8),
Remark 2158 - ^ Unnecessary/redundant use of Offset operator
Address those two remarks in coreboot.
BUG=N/A
TEST=Build coreboot and check build log to see no more remark.
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: Iad660347b32d90ac1176654820375e30a21b5ffe
Reviewed-on: https://review.coreboot.org/c/31666
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Bora Guvendik <bora.guvendik@intel.com>
|
|
Since ACPI v2.c, this field is access_size.
Currently, coreboot is using ACPI v3,so we can drop '.resv' field.
Change-Id: I7b3b930861669bb05cdc8e81f6502476a0568fe0
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/31701
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
PCI config accessors are no longer indirectly included
from <arch/io.h> use <device/pci_ops.h> instead.
Change-Id: I2adf46430a33bc52ef69d1bf7dca4655fc8475bd
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/31675
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
This patch adds SOC_INTEL_COMETLAKE Kconfig option.
Change-Id: I2b0c269ade84d72cffaf59a0b53e0d6e3a84b835
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/31282
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-by: Ronak Kanabar <ronak.kanabar@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change ac8c60e (soc/intel/cannonlake: Disable ACPI mode as part of
pmc_soc_init) moved disabling of ACPI mode to pmc_soc_init to keep it
more aligned with the behavior on other Intel SoCs. However, as the
PMC device is hidden, it never gets enumerated and so init function
does not get called for it. This change moves the call to disable ACPI
mode to exit of BS_DEV_INIT instead.
BUG=b:126016602
TEST=Verified that:
1. pmc_set_acpi_mode is actually getting called.
2. EC panic event gets logged to eventlog correctly.
Change-Id: Ie7025e322fa0abc21367a520184a4c7741eba1e6
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/31633
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
TEST=Verify PM_STS1 value is is not 0xFF.
Change-Id: I932585f6e7525830bd57ecfc372bf3120e7cca66
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/31434
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch adds CML-U 2+2 SA DID into systemagent.c and report
platform.
Change-Id: I2e882a560dd0a1e96d6e1405735c6f7389c0db5a
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/31638
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Ronak Kanabar <ronak.kanabar@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
SD controller in CNL-PCH provides a ability to configure the behavior of
SD_VDD1_PWR_EN# as an active high or low signal. FSP provides an UPD
"SdCardPowerEnableActiveHigh" to control the same.
However, for platforms using SD_VDD1_PWR_EN# as active high, the SDXC
card connector is always powered and may impact system power. This is because
SD_VDD1_PWR_EN# does not de-assert during SDXC D3 or when SD card is not
inserted.
Workaround is to change the pad ownership of SD_VDD1_PWR_EN to GPIO and
force the TX buffer to low in _PS3. And restore the pad mode to native
function in _PS0.
Hence add a Kconfig option to update the UPD, which the board can select
based on how the SD_VDD1_PWR_EN is implemented on it. And, the workaround
gets applied based on this config.
BUG=b:123350329
Change-Id: Iee262d7ecdf8c31362aec3d95dd9b3e8359e0c25
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/c/31445
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add a function in gpio ASL library to enable/disable pad Rx/Tx Buffers.
BUG=b:123350329
Change-Id: I6c40d79debb61b0c4e96e485b410d446b77d9cf6
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/c/31619
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
PMC initialization on Cannon Lake happens earlier in the boot sequence
than other SoCs because FSP-Silicon init hides PMC from PCI bus. As
ACPI disabling was done as part of PMC init, it was being called
earlier than what other SoCs do. This resulted in a different order of
events for some drivers e.g. ChromeOS EC. In case of ChromeOS EC, it
ended up clearing EC events (which happens as part of ACPI disabling
in SMM) before logging any events of interest that happen during
mainboard initialization.
This change moves the call to disable ACPI to pmc_soc_init just like
other SoCs to keep the order of events more aligned.
BUG=b:126016602
TEST=Verified that EC panic event gets logged to eventlog correctly.
Change-Id: Ib73883424a8dfd315893ca712ca86c7c08cee551
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/31614
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Denote appropriate reserved groups as virtual GPIOs in Cannonlake LP/H SoC.
Change-Id: I4da161b91f83749b0ae29b387b5c99c1c3f706d8
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/c/31552
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Add cometlake specific PCH IDs
Change-Id: I18dda48cee29213aa66c0ccddf3da31f0f489d2f
Signed-off-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-on: https://review.coreboot.org/c/31234
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Add cometlake specific SA IDs
Change-Id: I1fbbab8a7797b36a9eacbd1c6a0644466f2fe6b1
Signed-off-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-on: https://review.coreboot.org/c/31226
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
|
|
Add cometlake specific CPU IDs
Change-Id: I75d5b82524c9df1402abf6659d62dbc716c28c30
Signed-off-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-on: https://review.coreboot.org/c/31143
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
|
|
CB:31547 fixes few whitespace error. Here is few more whitespace clean up.
Change-Id: I69c12a5da4feb48b2bc23874332ab341a559f6e6
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/31563
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
|
|
devicetree
Tested on system76 galp3-c
Signed-off-by: Jeremy Soller <jeremy@system76.com>
Change-Id: I3aa8990a335e413628c016007ebabf7142aef80d
Reviewed-on: https://review.coreboot.org/c/31535
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Add a function in gpio ASL library to set pad mode.
BUG=b:123350329
Change-Id: I6c683f27ddffc3132001706d1694c71bb5664577
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/c/31444
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Change-Id: I33a50e9fc90162c7cb2aa7fbc3887efe9c6ebcde
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/31547
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
For CFL and WHL, Microcode is being loaded from FIT. Both
supports the PRMRR/SGX feature. If This is supported the FIT
microcode load will set the msr (0x08b) with the Patch id one
less than the id in the microcode binary. This results in
Microcode getting reloaded again in bootblock and ramstage.
Avoid the microcode reload by checking for PRMRR support.
CFL and WHL CPU die are based on KBL CPU so we need to have
this check, where CNL CPU die is not based on KBL CPU so
skip this check for CNL.
BUG=b:124126405
Signed-off-by: Ronak Kanabar <ronak.kanabar@intel.com>
Change-Id: I3311a7413d27044f9c819179e5b0cb9a67b46955
Reviewed-on: https://review.coreboot.org/c/31492
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
|
|
Variants of Hatch need to accommodate single channel DDR. Also,
removing const modifier as we'll need to set these fields
incrementally now. For the single channel configuration, we set
MemorySpdPtr10 to 0. For the dual channel configuration, we set
MemorySpdPtr10 to MemorySpdPtr00.
BUG=b:123062346, b:122959294
BRANCH=None
TEST=Boot into current boards and ensure that we have 2 channels as expected
Change-Id: Ice22b103664187834e255d1359bfd9b51993b5b6
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/31262
Reviewed-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch feeds PsysPmax setting to FSP through UPD and adds a
psys_pmax member in chip information so that we can set PsysPmax
through DT. The PsysPmax needs to be set correctly mapping to maximum
system power. Otherwise, system performance would be limited due to
the default PsysPmax setting in FSP is only 21W.
BUG=None
BRANCH=None
TEST=Set psys_pmax to an example value eg 101 in DT && put debug code
in FSP to print the PsysPmax value before sending to Pcode, ensure
the setting is correctly programmed.
Change-Id: Ia88ea17bc661a388c5b9bc3e59abc27c9f262977
Signed-off-by: Gaggery Tsai <gaggery.tsai@intel.com>
Reviewed-on: https://review.coreboot.org/c/31505
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch adds the _DSM method 5 and 6 for entering and exiting S0ix.
The _DSM method gets injected into DSDT table and called from kernel.
LPIT table is hardcoded in this patch but the proper way to implement
is to use inject_dsdt to make the _DSM methods available for soc's to
implement.
Calling the LPIT table from mainboard here so that with the current
implementation the platforms which do not have lpit support throw
compilation error.
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: Ia908969decf7cf12f505becb4f4a4a9caa7ed6db
Reviewed-on: https://review.coreboot.org/c/31101
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shaunak Saha <shaunak.saha@intel.corp-partner.google.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
New whiskeylake v-0 stepping have changed the graphics device id from
0x3EA0 to 0x3EA1 for celeron, so declare that in common code. Also the
CPUID was changed from 806EB to 806EC, include that as well.
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: Ief5213a96507124b90f8dd2eeea2f6bf43843dc6
Reviewed-on: https://review.coreboot.org/c/31433
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
"mosys memory spd print all" returns incorrect memory ranks info.
This patch and 2 upcomming ones (one in FSP) will address the issue.
BUG=b:122329046
TEST=Boot to OS on Bobba variant of Octopus
BRANCH=octopus
Change-Id: I212215040e4786c258a9c604cc5c2bb62867c842
Signed-off-by: Francois Toguo <francois.toguo.fotso@intel.com>
Reviewed-on: https://review.coreboot.org/c/31235
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Define VR settings configuration as per board design.
BUG=N/A
TEST=Build and boot up into sarien platform.
Change-Id: Ic9927943b1f8fab687659fd1d6da0e3988a3aba2
Signed-off-by: Roy Mingi Park <roy.mingi.park@intel.com>
Reviewed-on: https://review.coreboot.org/c/31405
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Set SerialIoDebugUartNumber to CONFIG_UART_FOR_CONSOLE
SerialIoDebugUartNumber UPD use to select UART Number for Debug Purpose
The default value of SerialIoDebugUartNumber is 2 by default it selects UART 2
so it needs to be initialized as per board config
BUG=b:123702398
Change-Id: I91df4bb756e8ea86db112f1cc28687f48b2c0525
Signed-off-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-on: https://review.coreboot.org/c/31375
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
All platforms using this code have NO_CAR_GLOBAL_MIGRATION.
Change-Id: I72effa93e36156ad35b3e45db449d8d0d0cabf06
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/30514
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
FSP-S is currently configuring GPIOs that it should not. This results
in issues where mainboard devices don't behave as expected e.g. host
unable to receive TPM interrupts as the pad for the interrupt is
re-configured as something else.
Until FSP-S is fixed, this change adds a workaround by reconfiguring
GPIOs after FSP-S is run.
All mainboards need to call cnl_configure_pads instead of
gpio_configure_pads so that SoC code can maintain a reference to the
GPIO table and use that to re-configure GPIOs after FSP-S is run.
BUG=b:123721147
BRANCH=None
TEST=Verified that there are no TPM IRQ timeouts in boot log on hatch.
Change-Id: I7787aa8f185f633627bcedc7f23504bf4a5250b4
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/31250
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
This patch performs below tasks
1. Create SOC_INTEL_COMMON_CANNONLAKE_BASE kconfig.
2. Allow required SoC to select this kconfig to extend CANNONLAKE
SoC support and add incremental changes.
3. Select correct SoC support for hatch, sarien, cflrvps
and whlrvp.
* Hatch is WHL SoC based board
* Sarien is WHL SoC based board
* CFLRVP U/8/11 are CFL SoC based board
* WHLRVP is based on WHL SoC
4. Add correct FSP blobs path for WHL SoC based designs.
Change-Id: I66b63361841f5a16615ddce4225c4f6182eabdb3
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/31133
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This patch removes duplicate selects of same SOC_INTEL_CANNONLAKE_MEMCFG_INIT
from various CFL/WHL SoC based boards to include cnl_memcfg_init.c file
and include the cnl_memcfg_init.c file by default in CNL SoC Makefile.inc.
Change-Id: Ib21ea305871dc859e7db0720c18a9479100346c3
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/31134
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
TEST=Dump SSDT entries to verify _CST between S0ix enable and disable.
Change-Id: I25e8f8c13bb91c2645e8e9fdfdf9ba4d7022f1b1
Signed-off-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-on: https://review.coreboot.org/c/31154
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
|
|
Commit dc666f5 (soc/intel/cannonlake: Change in SaGv options) added a
conditional preprocessor directive, but its condition was incorrect
because SOC_INTEL_CANNONLAKE is selected for CNL, CFL and WHL. Thus, an
explicit check for !SOC_INTEL_COFFEELAKE is required.
While we are at it, clean up the comment above a bit.
BUG=b:123184474
Change-Id: I8a6959bb615fb5668cbfe54339747d135bd5a005
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/31095
Reviewed-by: Shelley Chen <shchen@google.com>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Export the SOC level function to set the After G3 state so it
can be changed by the mainboard. The setting will be restored
by a normal boot but in some circumstances coreboot wants to
ensure that it will be powered up again after a reset.
BUG=b:121380403
TEST=update cr50 firmware on sarien and reboot and ensure the
host does not power off after the cr50 initiated reset.
Change-Id: I6cd572ac91229584b9907f87bb4b340963203c32
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/31056
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Disabling CpuRatio UPD for FSP will ensure it does not force a
hard reset to set the CPU Flex Ratio at boot. This is important
in a recovery mode boot where the SOC will lose power and need
to set the flex ratio again.
Disabling SaGv makes recovery mode training faster and mirrors
the setting that was done on Skylake.
BUG=b:123305400
TEST=reliably enter recovery mode on sarien
Change-Id: Ie9664493a980af9acce82faff81f4c4b1355be73
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/31055
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Replace device name from B0D4 with TCPU for DPTF sensor. This
helps to maintain consistency between coreboot and UEFI BIOS.
Change-Id: I962d74fc1baa07581d065734aaabb4dcd5e3d247
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/31029
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Change-Id: I614ea7f0f74326e306649779266001cf25ce5e07
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/30955
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
|
|
CNL,WHL and CFL all are not using midfixed option in SaGv so keeping it for
CNL only and removing it for others.
Change-Id: I754515c2f8e249479c603872c61ac9a006e962ff
Signed-off-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-on: https://review.coreboot.org/c/30917
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
According to EDS #565870 chapter 5.3.1, AG3E bit in PMC located in PMC
memory mapped register but not pci config spaces. Change the programming
to affect that difference.
BUG=b:122425492
TEST=Change System Power State after failure to "s5 off", and boot up
onto sarien platform, check the register with iotools mmio_read32
0xfe001020 and bit 0 is set.
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: I0934894558fd9cbc056dea8e7ac30426c2529e4e
Reviewed-on: https://review.coreboot.org/c/30945
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
conf pointer could be null, access it only if its not null.
Foundby=klocwork
BUG=N/A
TEST=N/A
Signed-off-by: Pratik Prajapati <pratikkumar.v.prajapati@intel.com>
Change-Id: I1b3d6f53d2bfd9845ad7def91c4e6ca92651d216
Reviewed-on: https://review.coreboot.org/c/30860
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
|
|
Add processor power limits control support to configure values.
BRANCH=None
BUG=b:122343940
TEST=Built and tested on Arcada system
Change-Id: I5990dc05b51481a0074855914cef20cf07378cde
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/30907
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Does not fix 3rdparty/, *.S or *.ld or yet.
Change-Id: I66b48013dd89540b35ab219d2b64bc13f5f19cda
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/17656
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
This change provides an interface for canonlake to set TCC.
With this change, we can add code to update Tcc in devicetree.
BUG=b:122636962
TEST=Match the result from TAT UI
Change-Id: Ib54a118e4e409919e3e60112e4621a109404b16d
Signed-off-by: John Su <john_su@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/30803
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
|
|
Hook Coffeelake U43e and Coffeelake H/S/E3 microcode into SOC and remove
the MICROCODE_BLOB_NOT_HOOKED_UP.
BUG=N/A
TEST=Boot up with coffeelake rvp board and check microcode revision in
coreboot log.
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: I6593081374dd4898a82db5b43c3b5bf154b3ef60
Reviewed-on: https://review.coreboot.org/c/30864
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
TCO2_STS_SECOND_TO was renamed to TCO_STS_SECOND_TO but one use
slipped through.
Change-Id: I9e3b1cc5cb2f319db35416edf6cea612d755d40a
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/30805
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch cleans soc/intel/{apl/cnl/icl/skl} by moving common soc
code into common/block/smbus.
BUG=b:78109109
BRANCH=NONE
TEST=Build and boot KBL/CNL/APL/ICL platform.
Change-Id: I34b33922cafee9f31702587e0f9c03b64f0781b8
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/26166
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
The option to specify a binary file name was added later for platforms
that do not provide microcode updates in our blobs repository. Alas,
it wasn't visible what platforms these are. And if you specified a file
for a platform that already had one, they were all included together.
Make it visible which platforms don't provide binaries with the new con-
figs MICROCODE_BLOB_NOT_IN_BLOB_REPO, MICROCODE_BLOB_NOT_HOOKED_UP and
MICROCODE_BLOB_UNDISCLOSED. Based on that we can decide if we want to
include binaries by default or explicitly show that no files are inclu-
ded (default to CPU_MICROCODE_CBFS_NONE).
Also split CPU_MICROCODE_CBFS_GENERATE into the more explicit
CPU_MICROCODE_CBFS_DEFAULT_BINS and CPU_MICROCODE_CBFS_EXTERNAL_BINS.
And clean up the visibility of options: Don't show CBFS related options
on platforms that don't support it and don't show external file options
if the platform uses special rules for multiple files (CPU_MICROCODE_
MULTIPLE_FILES).
Change-Id: Ib403402e240d3531640a62ce93b7a93b4ef6ca5e
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/c/29934
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Everything is wrong here, the Kconfig symbols are only the tip of the
iceberg. Based on Kconfig prompts the SoC code performed pad configu-
rations! I don't see why the person who configures coreboot should have
the board schematics at hand.
As a mitigation, we remove the prompts for UART_DEBUG, which is renamed
to INTEL_LPSS_UART_FOR_CONSOLE (because the former didn't really say
what it's about), and for UART_FOR_CONSOLE in case the former is selec-
ted.
Change-Id: Ibe2ed3cab0bb04bb23989c22da45299f088c758b
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/29573
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
This patch provides an option to enable or disable IPU (image processing unit),
* Add an entry for SA IPU in the pci_devs.h.
* Enable/Disable the IPU based on devicetree entry.
Change-Id: Ia155bc242dd33e816d056bbea1e3d4c1cbbe23da
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Reviewed-on: https://review.coreboot.org/c/30698
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Expose the FSP tunables for the chipset minimum assertion width
settings which can be configured per-board.
The defaults appear to be different from what is listed in the FSP
header documentation so I tried to list what the actual default is
based on the source rather than what is stated the header comments.
Change-Id: Ie0606c2984727adf13c9fb8395586287162e49ca
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/30719
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
|
|
Add logging of chipset events on boot into the flash event log.
This was tested on a google/sarien board to ensure that events
like "System Reset" are added to the log as expected.
Change-Id: I38498cef36d8cc9c8a1f63d12618ea768b65254c
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/30718
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
|
|
This structure is declared as a static CAR_GLOBAL in the common
PMC library code and in the SOC specific code. Remove the SOC
specific version and instead get the chipset_power_state pointer
from the PMC library.
This fixes events that were recorded in chipset_power_state at
boot but were reading as all zero when it was time to parse the
structure when logging events to flash.
Change-Id: I67a4f724c0707d98766ad28abd8d0b66a5615745
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/30717
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
|
|
Use defined name in Intel 64 and IA-32 Architectures Software
Developer’s Manual.
Renamed MSRs are (register address, register name):
0x35 MSR_CORE_THREAD_COUNT
0x121 MSR_EMULATE_PM_TIMER
0x1f4 MSR_PRMRR_PHYS_BASE
0x1f5 MSR_PRMRR_PHYS_MASK
0x2f4 MSR_UNCORE_PRMRR_PHYS_BASE
0x2f5 MSR_UNCORE_PRMRR_PHYS_MASK
Change-Id: I53f11a2ce831456d598aa21303a817d18ac89bba
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/30288
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
|
|
It's not needed anymore.
Change-Id: I273acb2bf1675dc947927e3e6d2ebb78aa94518a
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/29681
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
|
|
Follow instrcution from https://doc.coreboot.org/acpi/gpio.html to
implement GPIO toggling method, covered for both CNP_LP and CNP_H pch.
BUG=N/A
TEST=Build and boot up fine on sarien platform, add an dummy STSX in
DSDT table, read back from iotools to confirm the GPIO tx state get
updated.
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: I006a6a8fc580c73ac0938968397a628a4ffe504f
Reviewed-on: https://review.coreboot.org/c/30461
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Set PchCnvimode to Auto if CNVi is enabled in device tree. This will
allow FSP to configure CNVi.
Change-Id: I4f77fe5e9f561d3b498403e42dfc7afdcfaedf6f
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/30516
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Expose the FSP interface to enable SATA and PCH side DMI power optimize
options. Actual step executed in FSP, step defined in cannonlake pch
BIOS spec(CDI# 570374).
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: Ic0c589bb21e56800090bc0c75a0256a0409efc78
Reviewed-on: https://review.coreboot.org/c/30211
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Update HDAenable bit in Fsp memory init UPD data base on devicetree
settings.
BUG=N/A
TEST=N/A
Change-Id: I5159c00a855a2a9516714ccee8ee9933465c5063
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/c/30097
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
FSP support two SATA modes as AHCI mode (0) and RAID mode (1), make it
more clear in header file.
Change-Id: I1edcadc0048df839da145260b60f9f7720d981fe
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/c/30093
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
CPU ratio will be fixed to non-turbo max value if CpuRatio UPD had been
set to zero.
BUG=N/A
TEST=Boot up into sarien system, cat /proc/cpuinfo and cpu frequency is
changing.
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: I3e82293c8b6027ddf9a528d0654fe46f233dcb82
Reviewed-on: https://review.coreboot.org/c/30216
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Fix typo of "VGOIO" back to "VGPIO".
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: Ia2b7cb0e5fe2817acc3e3f4656b98dc2462b397f
Reviewed-on: https://review.coreboot.org/c/30147
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Bora Guvendik <bora.guvendik@intel.com>
|
|
Change-Id: Idef8c556ac8c05c5e2047a38629422544392cd62
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/30200
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Expose the following FSP UPD interface into coreboot, which is the
following:
AcousticNoiseMitigation
FastPkgCRampDisableIa
FastPkgCRampDisableGt
FastPkgCRampDisableSa
FastPkgCRampDisableFivr
SlowSlewRateForIa
SlowSlewRateForGt
SlowSlewRateForSa
SlowSlewRateForFivr
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: I21f53c594a085794474e87eb6781b51db88d0c10
Reviewed-on: https://review.coreboot.org/c/30207
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
The GPIO pin map for CNL-H does not match with the OS expected
pin numbers. This has been updated to match what is used by the
Linux kernel pinctrl driver and the pad base has been set for
the GPIO groups to match the sparse GPIO map used by the kernel.
I do not have CNL-H hardware to test this so it is verified against
the kernel driver at drivers/pinctrl/intel/pinctrl-cannonlake.c
Change-Id: Ife7d3090d654b0b88c6911befa08bf6abd4f2ff9
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/30134
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The GPIO drivers in Windows and Linux for the Cannonlake CPU
have a sparse GPIO map and do not allocate pins contiguously.
Each GPIO group is allocated as 32 pads regardless of whether
the hardware actually has that many in the group.
It appears this originated with a bug in Windows/UEFI and was
carried over to Linux in order to work with existing firmware:
https://lore.kernel.org/patchwork/patch/855244/
In order to support using ACPI GPIOs it is necessary for coreboot
to be compatible with this implementation. The GPIO groups that
are usable by the OS are declared with a pad base which is then
used to compute the number for ACPI GPIOs.
BUG=b:120686247
TEST=tested with write protect GPIO on sarien board. Before this
change the ACPI pin number was 220 which did not correspond to the
pin number in Linux. After this change the ACPI number is 303,
which maps to the correct GPIO in Linux. Now the GPIO value reported
by the kernel changes when the WP pin is toggled in hardware.
Change-Id: I4f1a9e118d7e48f2445ccbb62a12a22e9a832c51
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/30133
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This patch introduces 3 helper function for cpuid(1) :
1. cpu_get_cpuid() -> to get processor id (from cpuid.eax)
2. cpu_get_feature_flags_ecx -> to get processor feature flag (from cpuid.ecx)
3. cpu_get_feature_flags_edx -> to get processor feature flag (from cpuid.edx)
Above 3 helper functions are targeted to replace majority of cpuid(1)
references.
Change-Id: Ib96a7c79dadb1feff0b8d58aa408b355fbb3bc50
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/30123
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
The kernel GPIO driver only expects some GPIO communities to be exported
in the _CRS and it will not work correctly if the other communities are
exported.
CNL-LP: GPIO communities 0, 1, 4
CNL-H: GPIO communities 0, 1, 3, 4
Additionally one of the pin offset values was incorrect in GPIO
community 1 for CNL-LP. This doesn't have any specific failure mode but
it was found when auditing the GPIO code.
Details of the kernel expected map can be found in the linux kernel at
drivers/pinctrl/intel/pinctrl-cannonlake.c
BUG=b:120686247
TEST=check /sys/kernel/debug/pinctrl/INT34BB:00/pins to ensure that
pins >= 198 are not reading all zeros for the pin config registers.
Change-Id: Ie1a2f3b9f9f4b24a9fc57e468dee50e99753912f
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/30112
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
The input clock for the I2C controllers was set at 133MHz but should
really be 216MHz according to the kernel:
https://patchwork.kernel.org/patch/10408729/
"Intel Cannon Lake PCH has much higher 216 MHz input clock to LPSS I2C
than Sunrisepoint which uses 120 MHz. Preliminary information was that
both share the same clock rate but actual silicon implements elevated
rate for better support for 3.4 MHz high-speed I2C."
This change was tested on a sarien board where an I2C trackpad that was
measuring ~700MHz on I2C and is now measuring ~380MHz.
Change-Id: I792d1f013da5538a2b8157e2f99b754ca7b6bf70
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/30061
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add the ACPI device names for the USB ports to match what
is in the DSDT so USB ports can be defined in the SSDT.
Change-Id: Ibb323bbd324811fa3178b0cba3d7f0a315169486
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/29997
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Increase the bootblock size to 48K to match skylake. With UART
enabled we are very near the 32K limit, and with upcoming changes
to add USB devices in devicetree for a cannonlake board it is over
the current 32K limit.
Change-Id: I155cb0a6af1746af6833fa9f35c2ea6fe0bc709f
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/29996
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Define the constants that DPTF expects from the SOC in order to
use the common DPTF ACPI code. For cannonlake this indicates
the CPU device is called B0D4 and is at PCI address 00:04.0.
Change-Id: I43c2f8dd7281d3e9f791ab01478ee7823fd6b128
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/29759
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Make build still pass in case of no FsptUpd.h available.
BUG=N/A
TEST=Delete FsptUpd.h and build pass wihtout FSP_CAR set.
Change-Id: I3936d3deb8b079bd4db11e444f6bb7f9605520dc
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/c/29907
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Change-Id: Ifa5a3a22771ff2e0efa14fb765603fd5e0440d59
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/29894
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: David Guckian
|
|
Use acpigen_write_processor_cnot to implement notifications to the CPU.
Change-Id: Id64f9857bbd7db520c94de949db8f823f71d6dae
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/29891
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
TEST=Able to build and boot successfully.
Change-Id: If013d8e59046152e9f1a026f48bd9cd9b43ab6af
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/29836
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change makes the early IO decode setup mirror that of other
Intel SOCs and fixes issues with COM1 not being enabled properly.
Tested by successfully successfully receiving serial output from
an 8250IO UART device at the standard 0x3f8 base address.
Change-Id: I9bd894fea62b78b81e5c80b5e88a539ebddac2df
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/29671
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
|
|
soc_pch_pirq_init() function is only getting compiled for RAMSTAGE
hence remove unused __SIMPLE_DEVICE__ check.
Change-Id: I7f0ca62170f0af12a251c8c97155de8433a31854
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/29643
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
FSP can support enable/disable Pci express LTR (Latency Tolerance
Reporting) mechanism through upd interface. Include that into coreboot
side.
BUG=N/A
TEST=N/A
Change-Id: I69b423afa4f81a2d58375734bba07792e08931d5
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/29642
Reviewed-by: Pratikkumar V Prajapati <pratikkumar.v.prajapati@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I89e03b6def5c78415bf73baba55941953a70d8de
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/29302
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|