| Age | Commit message (Collapse) | Author |
|---|
|
At least a part or the remaining definitions in the soc-specific smi.h
files are also common, but those have to be verified more closely.
Change-Id: I5a3858e793331a8d2ec262371fa22abac044fd4a
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48217
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
SMBHST_STAT_NOERROR was a redefinition of SMBHST_STAT_INTERRUPT that was
used in smbus_wait_until_done. Remove the misleading bit definition that
also didn't correspond with the register definitions and replace it with
the definition of the actual bit that gets checked. Also add a comment
that the code actually checks the IRQ status flag to see if the last
command is already completed.
Change-Id: I1a58fe0d58d3887dd2e83320e977a57e271685b3
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48219
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
Change-Id: I6df9323dc4e7ca99fd5368f0262e850c0aca5c54
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48218
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
The patch also rewrites the bit definition using shifts to make them
easier to read.
The older non-SoC chips can probably also use the new header file, but
for this patch the scope is limited to soc/amd, since the older non-SoC
chips don't use the SMBUS controller code in soc/amd/common.
TEST=Timeless build for amd/mandolin and amd/gardenia doesn't change.
Change-Id: Ifd5e7e64a41f1cb20cdc4d6ad1e675d7f2de352b
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48188
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
The code on Stoneyridge didn't set the FCH_AOAC_TARGET_DEVICE_STATE bits
to FCH_AOAC_D0_INITIALIZED like the code for Picasso does, but that is
the default value after reset for those bits on both platforms.
Change-Id: I7cae23257ae54da73b713fe88aca5edfa4656754
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48183
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
The register locations and bit definitions are the same for Stoneyridge
and Picasso. Since not all devices are present on all SoCs, keep those
numbers in the SoC-specific code.
Change-Id: Ib882927e399031c376738e5a35793b3d7654b9cf
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48182
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
Now that the initial version of the Picasso FSP binaries have finally
landed, we can set the default paths to point to them now.
Change-Id: Ib2241cc90c7113e0c3de4409e08b9ae1f4c2f51e
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42472
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Jason Glenesk <jason.glenesk@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
In commit 09d50671e6b43c23853a91ff4d6fb26c1e7e17a1 the AOAC code was
reworked for Picasso and this patch ports this back to Stoneyridge to
facilitate factoring out the functionality into common code.
Change-Id: I836b91dc647987d064170fff7c8ca6ef2ee49211
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48181
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
The numbers in the array are unsigned, so use an unsigned type there.
Change-Id: I9a85594de0e4c53db965ab84239f19eb46432348
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48180
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
The power_off_aoac_device function clears the FCH_AOAC_PWR_ON_DEV bit,
so the comment should be that it powers off the devices.
Change-Id: Ia5e5d80b1977c3f53fcd9cf6d48bdb59045dfc3c
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48155
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
PICASSO_LPC_IOMUX was only used in the amd/mandolin board, but not in
the corresponding SoC code, so remove it from the SoC's Kconfig and
reanme it in the mainboard's Kconfig to MANDOLIN_LPC.
Change-Id: I261e093d6c56be6073a816b79c60d3a0457616f8
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47891
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
The corresponding functionality in the SoC's Makefile.inc was removed in
commit ef3395d990bbf1118a8d4e367a986bdbc92b1820
Change-Id: Iba84d9deb155ce314b3a3588781752b83a21486b
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47890
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
There's no need to have the bootblock in its own sub-directory, so move
it to each SoC's main directory to avoid clutter. This makes soc/amd
more consistent with the coreboot code base in src/northbridge,
src/southbridge and src/soc with the exception of src/soc/intel.
Change-Id: I78a9ce1cd0d790250a66c82bb1d8aa6c3b4f7162
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47982
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
show_psp_transfer_info reimplemented the functionality of
transfer_buffer_valid, so use replace that with a function call.
Change-Id: Ie3d373b10bdb0ab00640dabeea12b13ec25406cc
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47977
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Change-Id: I4f07d3ab12116229a13d2e8c02b2deb06e51a1af
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47976
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Change-Id: I9e9fed26a686b8f90797687dd720902be48dae72
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47975
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
There will be more files added to the common non-CAR Makefile.inc, so
use an ifeq statement there.
Change-Id: I1f71954d27fbf10725387a0e95bc57f5040024cc
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47880
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Add a Kconfig symbol for including the PCIe MMCONF setup function in the
build and select it when SOC_AMD_COMMON_BLOCK_PCI is selected and in the
southbridges call enable_pci_mmconf(), but don't select
SOC_AMD_COMMON_BLOCK_PCI.
Change-Id: I32de7450bff5b231442f9f2094a18ebe01874ee7
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47878
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: Ie347ee508acd900353467b4a3e0a5d1928b110e1
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47877
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
If there are multiple statements that are conditional on the same
Kconfig option, group them and move the condition check around the
statement. If there's only one statement depending on one condition, use
the short form instead.
Change-Id: I89cb17954150c146ffc762d8cb2e3b3b374924de
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47876
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Since there are sub-directories for both the cache-as-RAM case and the
non-CAR case where the RAM is already initialized when the x86 cores are
released from reset, move the CAR-specific parts of the Makefile.inc to
another Makefile.inc in the car sub-directory. Further patches will add
a Makefile.inc to the non-CAR directory.
Change-Id: I43a3039237d96e02baa33488e71c5f24effe8359
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47875
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
From spec, [31:28] "HS DC Voltage Level Adjustment" is "TXVREFTUNE0".
correct rx_vref_tune -> tx_vref_tune
BUG=None
BRANCH=zork
TEST=emerge-zork coreboot
Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com>
Change-Id: I27003a952d8f8bdd8fe52af8a37010e23ee9cdfd
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47735
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
AMD family 17h and newer don't use cache as RAM, since the RAM is
already initialized by the PSP when the x86 cores are released from
reset. Therefore they use a different linker script as the rest of the
x86 chips in coreboot do. Since there will be support for newer
generations than Picasso will be added, move those linker scripts from
soc/amd/picasso to soc/amd/common/block/cpu/noncar.
TEST=Timeless build of amd/mandolin and amd/gardenia result in identical
binaries.
Change-Id: Ie60372aa498b6e505708f97213b502c9d0b3534b
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47828
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
Change-Id: I7f976c6c5a2a715e1a5372bb93fe657d0d86c848
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47584
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I215058bcb0d53bfec974b8d3721cb4c998fcbee5
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47702
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
By renaming the AMD SOC common Kconfig file the wildcard to source all
AMD SoC-specific Kconfig files won't match to it and it can be sourced
after all SoC-specific Kconfig files in the sub-directories are sourced.
This change allows adding new SoCs without having to edit the soc/amd
Kconfig file.
Change-Id: Iaaa5aad23eb6364d46b279101f3969db9f182607
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47701
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Different models within family 17h have different PCI IDs for their PCIe
GPP port and internal bus devices.
Change-Id: I386df908ce5451b4484be2a2e4a9018c3d47d030
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47677
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
Different models within family 17h have different PCI IDs for their data
fabric PCI devices.
Change-Id: I44f8d32c950710e962dc519495b08c92f357ed20
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47676
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
The code that uses the GPU device ID uses the correct ATI vendor ID, but
the description wrongly used AMD as vendor. In the AMD APUs the GPU PCI
device and the corresponding audio controller use the ATI PCI vendor ID
while all other PCI devices in the SoC use the AMD PCI vendor ID.
Also move the two entries in a separate section right below the one they
were in.
Change-Id: Ia0b5bd4638f5b07c487f223321872563b36337e9
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47674
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
SOC_AMD_COMMON needs to be selected to be able to select
SOC_AMD_COMMON_BLOCK which only includes the Kconfig files from the
function block sub-folder. Removing SOC_AMD_COMMON_BLOCK and the
corresponding Kconfig file and make SOC_AMD_COMMON include all Kconfig
files from the sub-folders simplifies this a bit.
Change-Id: I9068d57a80bdc144e73d2b8c00e7b2cae730d4b6
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47672
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Jason Glenesk <jason.glenesk@gmail.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
"printk()" needs <console/console.h>.
Change-Id: Iac6b7000bcd8b1335fa3a0ba462a63aed2dc85b8
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45539
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
This change drops the inclusion of entry16.ld and reset16.ld and
instead adds the content of those files directly in memlayout_x86.ld
in amd/picasso. This is done to allow the work for top-aligning
bootblock to happen independent of Picasso layout. Once that is
complete, Picasso layout can be re-evaluated to see if it can make use
of the common bootblock linker file includes.
TEST=Verified that coreboot.rom generated using --timeless is the same
with and without this change for trembyle.
Change-Id: Ib1218b24a06d0f69b856fb21458a6183fd21fcbc
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43281
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Jason Glenesk <jason.glenesk@gmail.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
In the file uintptr_t that is defined in stdint.h and struct device that
is defined in device/device.h are used, so include them directly to
avoid having to rely on them being included in the file that includes
this header file.
Change-Id: I9893619924d45e5690a5cfc65252ace4cb7f1486
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47627
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
Since coreboot is written in C and not C++, having the double
underscores as a prefix is not an issue, but it also doesn't add much
information, so drop them and the trailing ones as well.
Change-Id: I1028fb9097efab8ffae5ffa9fe85a97feebc78a9
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47583
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I0cc06e33ed5c9b9bd97ed1f10f9c2d8019b1b5ac
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47582
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I980cdd03d4283cd4bd9db8bd90fde9a43bebc1e5
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47580
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
This also reduces the difference to the equivalent file from
stoneyridge.
Change-Id: I3fc44f057047995cc4054a85a1bb69427aa28531
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47581
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The SMU mailbox access code from Picasso can be reused in the next
generation, so factor out the code to soc/amd/common/block/smu. Since
the mailbox register offsets in the indirect address space, the number
of arguments and the message IDs don't always match between different
devices, keep those in the soc-specific directories.
Change-Id: Ibaf5b91ab35428e4c771e7163c6e0c4fc50371e7
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47483
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jeremy Soller <jeremy@system76.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
TEST=Timeless build doesn't change for Mandolin and Gardenia.
Change-Id: I1aef68459569536207697bfca407145a7b5334f4
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47515
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jeremy Soller <jeremy@system76.com>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Jason Glenesk <jason.glenesk@gmail.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
TEST=Timeless build doesn't change for Mandolin and Gardenia.
Change-Id: I5d3ae1459c333658f4c86388f1822d92ca13c658
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47514
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jeremy Soller <jeremy@system76.com>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Jason Glenesk <jason.glenesk@gmail.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
This prototype will be used outside of soc/amd.
Change-Id: Icc69cf8a910764b27edf64f0f527b8f6a9013121
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45813
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The cpu/car code only applies to pre-family-17h CPUs that still use
cache as RAM (CAR) and the PI code only applies to the pre-FSP vendor
code blob binaryPI interface.
Change-Id: I5a13d7e202bb745255fabb46110850c36b07de7a
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47274
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Currently, there's no check for the table being programmed. This skips
programming a table if the table size is zero, or the pointer to the
table has been set to NULL.
BUG=None
TEST=Set table pointer to NULL, table doesn't run.
BRANCH=Zork
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: I7d09b47e7d619428b64cc0695f220fb64c71ef4c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47307
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Expand fam17h to family 17h to make the help text slightly easier to
understand and add family 19h to the description of
SOC_AMD_COMMON_BLOCK_PSP_GEN2.
Change-Id: I9284c9c638e1d217d4605523dde004781f4343f9
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47275
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
Change-Id: Id4460eb596b080dec1a63a20869182170c3388af
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47250
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
The RV1 CPUID is already in the cpu.h file, but was still missing from
the CPU table in cpu.c.
Change-Id: Iad78cbe933b40e946d421e4c93e523f9e31f1089
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47249
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
On picasso's psp_verstage, the vboot hash is being calculated by
hardware using relatively expensive system calls. By increasing the
block size, we can save roughly 150ms of boot and S3 resume time.
TEST=Build & boot see that boot time has decreased.
BRANCH=Zork
BUG=b:169217270 - Zork: SHA calculation in vboot takes too long
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: I6642073357327811b415dcbcad6930ac6d2598f9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46903
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Increasing the vboot hash buffer size greatly speeds up the SHA
calculations. Going from a standard 4k buffer to a 36k buffer
takes ~150ms of the boot and resume time.
TEST=Build & boot see that boot time has decreased.
BRANCH=Zork
BUG=b:169217270 - Zork: SHA calculation in vboot takes too long
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: Ibca868ad7be639c2a0ca1c4ba6d71123d8b83c92
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46902
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The amdfwtool is not available at the beginning of the
building. So it may have error if it is missing.
Change-Id: Id4db70986755cef8e98877c4e92841b25ced5452
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47237
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
Use command below to change the variable globally.
sed -i "s/\<variable\>/variable_u/g" `grep variable -rl ./ \
--exclude-dir=build --exclude-dir=crossgcc`
BUG=b:171334623
TEST=Build
Change-Id: I056a76663e84ebc940343d64178c18cb20df01a3
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46840
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Since the mainboard Kconfig is sourced before the SoC one, it would
still be possible to override this setting at mainboard level, even
though that shouldn't be needed. The maximum CPU count for Picasso is 8,
since the chips have only up to 4 cores with up to two threads each.
Change-Id: I53449b8fa73c5d13e6ea77bee6eed8896b7d3ec3
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47205
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Two of the PSP mailbox commands are only applicable to the first
generation of PSP mailbox interface.
Change-Id: Ice940ee780c3d96ae1d9ec7ba49ea4add00e8723
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47180
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
Change-Id: I3a3d187fc24ab752dfe61893c15561a92d009fe2
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46062
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Initialize timestamp table with data from psp_verstage on bootblock.
PSP keeps its own timestamp and pass it in transfer_buffer. However PSP
timestamp and TSC may be out of sync so we can't just merge two tables
without modification.
info->timestamp contains PSP's clock value (in us) when x86 processor
released and base_timestamp contains TSC value when bootblock is
started. The time between x86 release and bootblock entry should be very
short so we can think those two happened at the same time and use them
for sync.
In some cases there will be underflow in timestamp entries but cbmem
utility can handle wrap-over in entries. Few timestamp values including
1st timestamp can be very large but we can still get the time spent on
boot without any problem.
BUG=b:159220781, b:167148121, b:171422583
BRANCH=zork
TEST=boot to kernel, run 'cbmem -t' and check verstage timestamps are
included in the result.
Change-Id: I5e89bb54f478153fb40ba51b5ab61fa20af3b99a
Signed-off-by: Kangheui Won <khwon@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45059
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
On Zork(picasso) platform we run verstage on the PSP. It has its own
timer, but the frequency is not matched with TSC.
To ease the work to merge timestamps from the PSP and TSC, add a layer
around tsc to have microsecond granularity for timestamp table. PSP
already records timestamp in microseconds.
BUG=b:159220781
BRANCH=zork
TEST=build, flash and boot, check timestamps are correct
Signed-off-by: Kangheui Won <khwon@chromium.org>
Change-Id: Ifced4a84071be8da547e252167ec21cd42f20ccc
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46058
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Eric Peers <epeers@google.com>
Reviewed-by: Rob Barnes <robbarnes@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Instead of having the same linker layout for the transfer buffer between
the x86 & PSP linker layout scripts, put the common layout into a file
shared between the other linker scripts.
BUG=None
TEST=Boot zork board, verify the buffers are aligned.
BRANCH=Zork
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: Ib9d9d8b046bc9e9e7a4ee939324960bfc44c3508
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46900
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
The last argument for acpi_fill_mcfg() is the last PCI bus, which is
an uint8_t, not the total number of busses, which overflows the
argument if CONFIG_MMCONF_BUS_NUMBER is 256.
Change-Id: I8887e14128dbe54688eb6e803d6694b7c29956c1
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35872
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Michał Żygowski <michal.zygowski@3mdeb.com>
|
|
Replace the initial bl_errorcodes_public.h (a temporary, minimal
version) with the full version released by AMD.
BUG=None
TEST=Build
BRANCH=Zork
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: I82585c74d74139a96419b9bffe1df3b8c344eb5f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45943
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Align coreboot's PSP MboxBiosCmdSmmInfo setup to how AGESA's PSP
library was implemented. The trigger address must be an SMI trigger
register. Assign one of the reserved triggers to the PSP.
The #define of SMITYPE_PSP 33 is still correct and is intentionally
unmodified.
This patch should be innocuous as the system doesn't currently support
SMI-based features of the PSP. The call only exists so the PSP will
honor a mailbox command during S3 suspend.
BUG=b:171815390
TEST=Run SST on Morphius
BRANCH=Zork
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Change-Id: I74029271a522a4f23e54fd76f99a8e3eb0dd4d55
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46854
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Jason Glenesk <jason.glenesk@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
To verify the consistency, see if timeless builds with and without
this patch result in identical coreboot.rom files.
BUG=b:154032833
TEST=Build & boot on mandolin
Change-Id: Icae73d0730106aab687486e555ba947796e5e757
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42859
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nikolai Vyssotski <nikolai.vyssotski@amd.corp-partner.google.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Include platform.asl to link acpi methods for _INI, _WAK, and _PTS to
correctly enable backlight in OS for zork.
BUG=b:158087989
BRANCH=Zork
TEST=check backlight during reboot and suspend
Signed-off-by: Josie Nordrum <JosieNordrum@google.com>
Change-Id: I702f807a5907d85d083295cf339ba9d31b246627
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46670
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Define device _WAK, _PTS, and _INI acpi methods with callbacks into
mainboard methods if provided.
BUG=b:158087989
BRANCH=Zork
TEST=tested backlight during reboot and suspend
Signed-off-by: Josie Nordrum <josienordrum@google.com>
Change-Id: I8020173a15db1d310459d5c1de3600949b173b00
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46669
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I1cabe0f55ec55a84f8e9028565be69c9dd997e7c
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45701
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Remove all typedefs and cleanup references to all structs and enums.
BUG=b:159061802
TEST=Boot morphius to shell.
Signed-off-by: Jason Glenesk <jason.glenesk@amd.corp-partner.google.com>
Change-Id: I403075e18886b566f576d9ca0d198c2f5e9c3d96
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46334
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
The Picasso build describes the DRAM region where the PSP places
our bootblock. Rather than relying on Kconfig values, make the build
more robust by using the actual size and target base address
from the boot block's ELF file.
Sample output of "readelf -l bootblock.elf" is:
------------------
Elf file type is EXEC (Executable file)
Entry point 0x203fff0
There is 1 program header, starting at offset 52
Program Headers:
Type Offset VirtAddr PhysAddr FileSiz MemSiz Flg Align
LOAD 0x001000 0x02030000 0x02030000 0x10000 0x10000 RWE 0x1000
Section to Segment mapping:
Segment Sections...
00 .text .data .bss .reset
------------------
We can extract the information from here.
BUG=b:154957411
TEST=Build & boot on mandolin
Change-Id: I5a26047726f897c57325387cb304fddbc73f6504
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46092
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The PSP does not accept the SmmInfo command during a resume so
remove the call.
BUG=b:163017485
TEST=Run SST on trembyle, verify error message goes away
BRANCH=Zork
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Change-Id: Ib75a20c9594bc331aa7abf77be95196085a3dbc6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44398
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Correct the base address. This should have no noticeable effect,
as SMC_MSG_S3ENTRY accepts no arguments and doesn't return. The
argument writes were not getting to any target.
BUG=b:171037051
TEST=Run SST on morphius
BRANCH=Zork
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Change-Id: Ie3402f743cf7d4f4f42b8afa3e8b253be4761949
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46505
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Change-Id: I3d5f595ebbc865501b086aebee1f492b4ab15ecd
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45700
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Replace vb2ex_hwcrypto_rsa_verify_digest with vb2ex_hwcrypto_modexp.
Instead of using hardware acceleration for whole RSA process,
acclerating only calculation part(modexp) increases transparency
without affecting boot time.
BUG=b:169157796
BRANCH=zork
TEST=build and flash, check time spent on RSA is not changed
Change-Id: I085f043bf2014615d2c9db6df0b7947ee84b9546
Signed-off-by: Kangheui Won <khwon@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45987
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
To remove the xhci0_force_gen1 and use usb3_port_force_gen1 instead.
The xhci0_force_gen1 is used for force all port on xhci0 to USB3 GEN1.
Now variant can use the usb3_port_force_gen1 to customize which port
it needs to limit.
BUG=b:167651308
BRANCH=zork
TEST=Build, verify the USB3 speed in gen1
Signed-off-by: Chris Wang <chris.wang@amd.corp-partner.google.com>
Change-Id: If5f0c1f22d8c98c4461f09d074bf082c340b14d9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46041
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
Reviewed-by: Sam McNally <sammc@google.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Add UPD usb3_port_force_gen1 for support USB3 port force to gen1.
BUG=b:167651308
BRANCH=zork
TEST=Build, verify the USB3 speed in gen1
Signed-off-by: Chris Wang <chris.wang@amd.corp-partner.google.com>
Change-Id: I896c185988c3ea5dbdd72957b363ebdaa2747cff
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45333
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
Reviewed-by: Sam McNally <sammc@google.com>
|
|
The PSP will now pass us data on the PSP boot mode and the production
silicon level. Print these values out to save in the log.
These definitions are in a vendorcode include directory that was
previously only included in verstage. Add the include directory
to all stages.
BUG=b:170237834
TEST=Build & Boot - See values printed.
BRANCH=Zork
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: Iee87413d1473786cf0e148a8088d27f8d24a47a1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46113
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
Reviewed-by: Sam McNally <sammc@google.com>
|
|
The transfer buffer check had gotten large enough to deserve a function
of its own, so break it out.
BUG=None
TEST=Build
Branch=Zork
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: Idf46f8edb6b70c63f623522e2bcd2f22d6d4790b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46112
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=b:169199392
TEST=Corrupt vboot signature to force an error, see that the system
halts instead of rebooting forever.
BRANCH=Zork
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: I949f94e78d25720f6cd7e81de8d030084e267f29
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45964
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
psp_verstage uses separate printk implementation, which does not include
code to add console output to cbmem.
Add cbmemc_init and cbmemc_tx_byte to add console output to cbmem.
BUG=b:159220781
TEST=build
BRANCH=zork
Change-Id: I63ba5814903565c372dbeb50004565a371dad730
Signed-off-by: Kangheui Won <khwon@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46059
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
Reviewed-by: Rob Barnes <robbarnes@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The PSP bootloader version 0.08.0B.7B added support for the Mod Exp
svc call.
BUG=b:169157796
BRANCH=zork
TEST=build verstage for zork
Signed-off-by: Kangheui Won <khwon@chromium.org>
Change-Id: Ifdbf20544b21b7fa90a49c5497ff4a5da61bebb1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45985
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Eric Peers <epeers@google.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
|
|
Added new config BOOT_DEVICE_SPI_FLASH_NO_EARLY_WRITES to accomodate
older x86 platforms that don't allow writing to SPI flash when early
stages are running XIP from flash. If
BOOT_DEVICE_SPI_FLASH_NO_EARLY_WRITES is not selected,
BOOT_DEVICE_SPI_FLASH_RW_NOMMAP_EARLY will get auto-selected if
BOOT_DEVICE_SPI_FLASH_RW_NOMMAP=y. This allows for current platforms
that write to flash in the earlier stages, assuming that they have
that capability.
BUG=b:150502246
BRANCH=None
TEST=diff the coreboot.rom files resulting from running
./util/abuild/abuild -p none -t GOOGLE_NAMI -x -a --timeless
with and without this change to make sure that there was no
difference. Also did this for GOOGLE_CANDY board, which is
baytrail based (and has BOOT_DEVICE_SPI_FLASH_NO_EARLY_WRITES
enabled).
Change-Id: I3aef8be702f55873233610b8e20d0662aa951ca7
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45740
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
The PSP will be adding information into these fields after verstage
runs. This allows data to be passed directly to coreboot very early
in the boot process.
BUG=b:168895748
TEST=None
Branch=Zork
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: Idbd1dfece59e99f6f15dfd8d002529ea6417cdbe
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45803
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Now that all boards have bootable driver strengths and init frequency,
we can pass them to FSP.
BUG=b:159823235
TEST=Boot ezkinil to kernel and print presets.
SDHC0x8F0 Initialization 3.3V or 1.8V => 0x03ff
14 => 0 [B]: DvrStrength
10 => 0: ClkGen
00 => 0x3ff: SdClkFreq
SDHC0x8F2 Default Speed 3.3V => 0x0004
14 => 0 [B]: DvrStrength
10 => 0: ClkGen
00 => 0x4: SdClkFreq
SDHC0x8F4 High Speed 3.3V => 0x0002
14 => 0 [B]: DvrStrength
10 => 0: ClkGen
00 => 0x2: SdClkFreq
SDHC0x8F6 SDR12 1.8V => 0x0008
14 => 0 [B]: DvrStrength
10 => 0: ClkGen
00 => 0x8: SdClkFreq
SDHC0x8F8 SDR25 1.8V => 0x0004
14 => 0 [B]: DvrStrength
10 => 0: ClkGen
00 => 0x4: SdClkFreq
SDHC0x8FA SDR50 1.8V => 0x0002
14 => 0 [B]: DvrStrength
10 => 0: ClkGen
00 => 0x2: SdClkFreq
SDHC0x8FC SDR104 1.8V => 0x4000
14 => 0x1 [A]: DvrStrength
10 => 0: ClkGen
00 => 0: SdClkFreq
SDHC0x8FE DDR50 1.8V => 0x0002
14 => 0 [B]: DvrStrength
10 => 0: ClkGen
00 => 0x2: SdClkFreq
SDHC0x900 HS400 => 0x4000
14 => 0x1 [A]: DvrStrength
10 => 0: ClkGen
00 => 0: SdClkFreq
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I5fe5c0a5a5ecf292ce8703e9c9ea80b6f1b6440e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45661
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
This allows passing in the presets to FSP.
I will set the UPD values after all the zork boards have had their
presets correctly set. This way we don't override the UPD defaults with
0s.
BUG=b:159823235
TEST=Build test
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I44951cacb1e9d788016a70283cf9688bf88a09f4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45097
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
Nearly every x86 platform uses the same arch for all stages. The only
exception is Picasso. So, factor out redundant symbols from the rest.
Alder Lake is not yet complete, so it has been skipped for now.
Change-Id: I7cff9efbc44546807d9af089292c69fb0acc7bad
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45731
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Add code to generate p-state and c-state SSDT objects to coreboot.
Publish objects generated in native coreboot, rather than the ones
created by FSP binary.
BUG=b:155307433
TEST=Boot morphius to shell and extract and compare objects created in
coreboot with tables generated by FSP. Confirm they are equivalent.
BRANCH=Zork
Change-Id: I5f4db3c0c2048ea1d6c6ce55f5e252cb15598514
Signed-off-by: Jason Glenesk <jason.glenesk@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45340
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Parse the generated fmap_config.h file instead of the .fmd file supplied
by the board to determine the size and location of the APOB region.
Parsing the generated file allows to write .fmd files without having to
take into account that the shell script part in Picasso's Makefile.inc
can only parse a subset of the .fmd syntax.
BUG=b:157068645
TEST=Timeless build for amd/mandolin resulted in identical binary.
BRANCH=zork
Change-Id: I6ed1903a8157374d78d2865621baa15774d2a7d7
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45595
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Verstage in PSP used stub for timestamps since we didn't know about
clock. Now we figured out clock source so we can enable timestamp
functions.
BRANCH=zork
BUG=b:154142138, b:159220781
TEST=build without CONFIG_PSP_VERSTAGE_FILE, flash and boot
Change-Id: I431a243878e265b68783f54ee9424bb1d4fe03c1
Signed-off-by: Kangheui Won <khwon@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45467
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Change-Id: Ib262955a1d26681c796c4b10d2b336f2715824d0
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44595
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
Change-Id: If8aa28a22625b7b2cf9b58958de87ee752f637f6
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45247
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
Fix function call to invoke 16-bit read in 16-bit api instead of 8-bit read.
Signed-off-by: Igor Bagnucki <bagnucki02@gmail.com>
Change-Id: Ifd9079fc6446125e0e58402fdb64bc198bb8e381
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45374
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
Add THERMCTL_LIMIT (die temperature limit) DPTC parameter
for clamshell/tablet mode.
BUG=b:157943445
BRANCH=zork
TEST=build
Change-Id: Id193a74210c92d1e45ed4824ee9c0fc9ceaa5e3a
Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45519
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
USE_PSPSCUREOS -> USE_PSPSECUREOS.
Change-Id: I5c89975cc317cb93e79509e885010d14a79dd7e1
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45285
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Clean up configuration of the legacy UART and add Kconfig options for
the mapping between UART and legacy I/O decode.
BUG=b:143283592
BUG=b:153675918
TEST=Linux detects an additional legacy serial port for each active MMIO
one if PICASSO_UART_LEGACY is selected.
BRANCH=zork
Signed-off-by: Rob Barnes <robbarnes@google.com>
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Id08ff6428d4019303ebb6e44e13aba480cf1fde2
Reviewed-on: https://chromium-review.googlesource.com/2037891
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40322
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
add dptc support for different power parameter on tablet/clamshell mode
The BIOS may choose to adjust power and/or thermal parameters at its own
discretion. The DPTC interface(DPTCi) ALIB Function adds flexibility by
allowing the BIOS to request power state changes independently of specific
events.
BUG=b:157943445
BRANCH=none
TEST=Build.Generated ASL code from SSDT by acipgen_dptci().check the setting changed.
Signed-off-by: Chris Wang <chris.wang@amd.corp-partner.google.com>
Change-Id: Icae94103f254f8fdb84e6ee0f5404fb09fa97b2d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43408
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
The register number is always non-negative, so it should be an unsigned
type.
Change-Id: I6b6df5a41fe58efc53eaa87c01b88426ea8daa6e
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45430
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
data_fabric.c uses types from stdint.h, but doesn't include stdint.h
directly, so replace the inclusion of stdbool.h with types.h which
includes both stdbool.h and stdint.h.
Change-Id: I4c1ea444e50218cf19fc8fff499929336265bd03
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45429
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Jason Glenesk <jason.glenesk@amd.corp-partner.google.com>
|
|
Memory speed is given as an integer in MHz. In some cases it has
an implicit fractional speed, so simply multiplying by 2 is not
sufficient.
Use method from dram/ddr4.c instead.
BUG=b:167155849
TEST=Boot ezkinil, check output of 'mosys memory spd print all'
and dmidecode -t17
BRANCH=Zork
Signed-off-by: Rob Barnes <robbarnes@google.com>
Change-Id: Icc77c21932c68ee9f0ff0b8e35ae7b1a3732b322
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45177
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This I/O region is already covered by the range declared right above the
deleted one.
Change-Id: I8b8ff3385bbba8e69101ee2c5a5cb39c8f996b94
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45369
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This I/O region is already covered by the range declared right above the
deleted one.
TEST=Linux stops complaining about overlapping I/O regions.
BRANCH=zork
Change-Id: I149fb0dc85bfe721a6b0d81e4e9c197194718876
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45368
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Jason Glenesk <jason.glenesk@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
I plan on adding another eMMC parameter. This refactor keeps the config
contained in a single struct.
BUG=b:159823235
TEST=Build test
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I4b57d651ab44d6c1cad661d620bffd4207dfebd4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45095
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
We added transfer_info_struct to contain various information about
memory region we pass from PSP to x86 in commit 0c12abe462.
This should be at the start of transfer region but we only manipulated
it as local variable and didn't put data into the region, resulting
garbage data for transfer_info when x86 tries to read it.
Copy the content of local variable to beginning of _transfer_buffer
before requesting transfer to PSP so coreboot on x86 can access it.
BUG=b:159220781
BRANCH=zork
TEST=check transfer_info_struct is correctly populated on romstage
Signed-off-by: Kangheui Won <khwon@chromium.org>
Change-Id: I14bc34e6af501240a6f633db3999a7759e88d60b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44751
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
That devicetree setting is about the Audio Co-Processor and not ACPI.
BRANCH=zork
Change-Id: I7f376371ee094392d4434340c77f0fc8d0d8e4e1
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45300
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
The AOAC device number is never negative, so make it unsigned.
BRANCH=zork
Change-Id: I3e0d15a646f02da5767504471961d5d9f8f28bea
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45308
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
