| Age | Commit message (Collapse) | Author |
|---|
|
Remove AcpiMmio and PCI config registers that are not used.
TEST=build Grunt
BUG=b:77602074
Change-Id: I62f40e421eba41c4a49d85efc975096171cb72fa
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/28864
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Remove the step of setting the SATA controller to S0 as the system is
entering S3. This had been duplicated from AMD's FchCarrizo.asl file,
but upon closer inspection, the conditions for this step to run cannot
be met. This does not affect Grunt's behavior, as the SATA controller
is disabled.
TEST=Suspend and resume Grunt
BUG=b:77602074
Change-Id: Ib269a5363d03c7048abd0c8a9a28df92a773790c
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/28863
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Use BIOS_DEBUG consistently to log PM1 and PMxC0 status registers
on boot. print_num_status_bits() was already using BIOS_DEBUG.
TEST=Inspect console for Grunt
BUG=b:110788201
Change-Id: If7da8c7c86e90a661338903ad05cc41e11f507d2
Signed-off-by: Edward Hill <ecgh@chromium.org>
Reviewed-on: https://review.coreboot.org/28885
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Implement the function vboot_platform_prepare_reboot() which is normally
a weak function.
The SlpTyp field of the PM1 register is not reset to its default value
when the APU restarts. This change prevents a failing condition if
vboot decides to reset the system instead of allowing an S3 resume to
continue.
TEST=Resume Grunt when vboot attempts a reset, verify a fresh boot instead
BUG=b:117089826
Change-Id: I6e0e3e541bad89ca5b23d6ddb6e5c0df7f762f10
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/28877
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable the IOMMU in AGESA and copy the AGESA generated IVRS ACPI table.
BUG=b:116196614
TEST=Check dmesg for AMD-Vi messages.
Change-Id: I688d867c7bd4949a57b27c1b6a793c6a6e4a717a
Signed-off-by: Marc Jones <marc.jones@scarletltd.com>
Reviewed-on: https://review.coreboot.org/28753
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Add methods, and call them, for transitioning EHCI and xHCI to D0 or
D3cold. Add device objects necessary for waking the system via USB.
In order for USB to wake the system, it must be in the D3cold state.
Then on resume, its firmware must be reloaded.
This code relies heavily on AMD's FchCarrizo.asl (delivered in NDA PI
package), and has been modified to fit the coreboot ASL names. In
addition, AMD's methodology is to generate a SW SMI for saving/restoring
certain settings. This has been ported into U3D0 and U3D3, as the
necessary registers are now publicly documented.
BUG=b:77602074
Change-Id: I83d0dce13411601691318cc67c99adf291ccf3bb
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/28772
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add a method to assist with setting the PwrGood Control register, which
will be useful for various devices.
BUG=b:77602074
Change-Id: Ief602c4bc42d27b3e236d24db815b990f3a2419c
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/28771
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Add methods that can be used for preparing all controller hub devices
for sleep, and that will turn the devices back on.
BUG=b:77602074
Change-Id: I4b0c48e96aff23b4c31c9e89582b9fa80dba7bda
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/28770
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Duplicate ASL from AMD's FchCarrizo.asl (available in NDA PI package)
that can put AOAC devices into D0 or D3cold. The argument numbers
coincide with the AOAC register offsets for the various devices.
SATA, USB, and SD require additional device configuration. Add a
placeholder and mark as todo.
BUG=b:77602074
Change-Id: I32426f744a5ebbad9e8d3f2f37c4d214ad6dd3d4
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/28769
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Define various AMD_SB_ACPI_MMIO_ADDR registers at 0xfed80000. Define
various PCI config space registers. These are duplicated from AMD's
FchCarrizo.asl file.
BUG=b:77602074
Change-Id: Ie7447fef682424b05fa912b60c7b80112c6202de
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/28768
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Indicate the devices that are enabled. This is somewhat rudimentary, but
could be improved in a later patch (e.g. get settings from devicetree).
Calculate values that may be used for reinitializing the xHCI firmware.
Add the EHCI BAR's current base address to gnvs.
BUG=b:77602074
Change-Id: I8af69c030eb2353ad75beeb2bfd3bef24abff04c
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/28767
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
A later patch will rely on two USB settings from the BIOS. Add these
to the global_gnvs_t structure.
The first is a data that will be used to locate the xHCI firmware for
reloading after a resume. Although the existing calculations will be
somewhat simple, keeping this on the coreboot side will help in the
event multiple FWs are eventually in the build.
The second item is a usable EHCI base address that may be programmed
during S3 suspend and resume. At the time the PTS and WAK code runs,
the BAR will be clear.
BUG=b:77602074
Change-Id: I32205ac8a6908cca4a38dd68a7c7b591e76c06bb
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/28766
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
A later patch will leverage AMD's ASL support for handling AOAC
devices. This will gather coreboot's device enables from a bitwise field,
where each bit corresponds to the register offset used to control
each devices.
Create an identical structure, and add it to the nvs ASL and global_nvs_t
structure.
BUG=b:77602074
Change-Id: I40f0161cc0bbc574ad703e34278372f2504de100
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/28765
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
|
|
The globalnvs.asl file had become mixed with tabs and spaces to align
columns. Use all tabs to align the comments.
BUG=b:BUG=b:77602074
Change-Id: Ife4cf86372a8e24e78b38cca0254dd9fa00dd6b0
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/28764
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
In preparation to remove AmdLib, remove reference to AmdLib.h in
soc/amd/stoneyridge/BiosCallOuts.
BUG=b:112525011
TEST=Buildgrunt.
Change-Id: If80eb64fb736ff26ab226a16b583c8b1c29831f4
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/28741
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Charles Marslett <charles.marslett@amd.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
In preparation to remove AmdLib, remove all references to AmdLib.h in folder
common/block/pi.
BUG=b:112525011
TEST=Buildgrunt.
Change-Id: I3530857b872d0cb5ed2e3f3a294cc50b45ff6969
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/28737
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Charles Marslett <charles.marslett@amd.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
As per internal discussion, there's no "ChromiumOS Authors" that's
meaningful outside the Chromium OS project, so change everything to the
contemporary "Google LLC."
While at it, also ensure consistency in the LLC variants (exactly one
trailing period).
"Google Inc" does not need to be touched, so leave them alone.
Change-Id: Ia0780e31cdab879d2aaef62a2f0403e3db0a4ac8
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/28756
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Joel Kitching <kitching@google.com>
|
|
Eliminate the references to PspBaseLib.c and PspBaseLib.h in
agesa_headers.h. Fix psp.c references to definitions in those files
by adding them to include/amdblocks/psp.h.
BUG=b:78514564
TEST=Build and boot grunt/ChromeOS and restore an image from the internet.
Change-Id: I2740ceb945736c6e413f7d0bd0c41a19e19c7d5a
Signed-off-by: Charles Marslett <charles.marslett@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/27619
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
STAPM programming was created inside function OemCustomizeInitEarly().
It should be SOC specific, and called by agesawrapper just before the
call to OemCustomizeInitEarly().
BUG=b:116196626
TEST=build and boot grunt
Change-Id: I8a2e51abda11a9d60a9057b38f2a484e1c8c9047
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/28705
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
When preparing transition of AGESA calls to romstage, I placed a comment
indicating the place to move a particular call. Now that the AGESA call
has been moved to romstage, the comment became obsolete.
BUG=b:116095766
TEST=none.
Change-Id: I2811657385ab088747e32d4c66b99fdd01e7315e
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/28687
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
According to AMD, there exists an undocumented MSR which must be
written with the PSP's base address. Read the value from the PSP's
config space and sync each core's copy of the MSR to match.
BUG=b:76167350
TEST=boot Grunt and verify "rdrand: disabled" goes away from dmesg
Change-Id: I30027d3b0a6fbd540375e96001beb9c25bf3a678
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/28608
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Default STAPM percentage causes a lot of thermal throttling on grunt.
AMD experimented with 80%, it works for grunt. This is initial code to
provide easy change path for other grunt based platforms.
BUG=b:111608748
TEST=build and boot grunt.
Change-Id: I22863f6ed76152bf872fce3e275f8a7fd8077504
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/28564
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Instead of gpio_num, gpio_address should be used as the address in
write32. This lets us also get rid of a few casts.
Commit c9ed3ee8d8 ("soc/amd/stoneyridge: Fix gpio_set function") fixed
one instance of this bug, but it was more widespread.
TEST=None
Change-Id: I0cf87aac2f1b87b6eac2b506515e48fe908c1f2b
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/28570
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Add a duplicate ACPI_BERT symbol with a 'y' default setting and additional
help text.
BUG=b:65446699
TEST=inspect BERT region, and dmesg, on full patch stack. Use test
data plus a failing Grunt system.
Change-Id: I817111cbd3e81b93d8b02d0654ba68c8678b1bbe
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/28479
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
|
|
Expand the BERT reserved region size setting to account for the
possibility of no TSEG configuration. This change is only for
completeness, as stoneyridge must always use TSEG.
Change-Id: I90753fa408cfac4de38aff08979c45349bb62a66
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/28554
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
|
|
Add a Boot Error Record Table to the ACPI information. Avoid a driver
error message by skipping the table altogether when no errors are found,
or support isn't built in.
BUG=b:65446699
TEST=inspect BERT region, and dmesg, on full patch stack. Use test
data plus a failing Grunt system.
Change-Id: I6fe38eefacaad0bc73d0cb4ae44a339a45857128
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/28478
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add functions to build a Boot Error Record Table region based on
settings found in the MCA registers.
Two entries are reported for each error due to the nature of the ACPI
driver. The first is a Generic Processor Error, which the OS recognizes
and parses. Generic errors cannot convey much error description or
processor context. Therefore an IA32/X64 Processor Error is also added,
which allows reporting the values found in the MCA MSR registers.
Follow-on work could decode the MC errors more precisely, and better
completing the Generic Error and the Check structure. The current
level of support is sufficient to identify a (i.e., human readable)
problem in dmesg, and provides adequate context information for
analysis.
BUG=b:65446699
TEST=inspect BERT region, and dmesg, on full patch stack. Use test
data plus a failing Grunt system.
Change-Id: I4d4ce29ddefa22aa29e6d3184f1adeaea1d5f837
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/28477
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Convert the Machine Check reporting to use a newly defined structure.
This will facilitate later patches that will pass pointers to the MSR
values.
BUG=b:65446699
TEST=inspect BERT region, and dmesg, on full patch stack. Use test
data plus a failing Grunt system.
Change-Id: I0a98aecc83a0fa1c5ca7926849a89145a595d9ff
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/28476
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Move the process of interrogating the Machine Check registers into
its own file. This rearranges source code in preparation of supporting
a Boot Error Record Table, which stoneyridge will use to report latent
MC errors to the OS.
BUG=b:65446699
TEST=inspect BERT region, and dmesg, on full patch stack. Use test
data plus a failing Grunt system.
Change-Id: Ia3275e9135dc96ba4a717c9371f38843fa1e3e64
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/28475
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Carve out memory to be reported to the OS as reserved. This makes
room for a region usable for Boot Error Record Table information.
The BERT region reserved size is larger than likely requried, however
the SMM region's base must be on a boundary matching the granularity
of its size.
BUG=b:65446699
TEST=inspect BERT region, and dmesg, on full patch stack. Use test
data plus a failing Grunt system.
Change-Id: I0958f6b6bab3fe9dae36c83e1fd9ae6ed0290a18
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/28474
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
- Remove unused acpi_get_chromeos_acpi_info (see CB:28190)
- Make function naming in gnvs.h consistent (start with "chromeos_")
BUG=b:112288216
TEST=compile and run on eve
Change-Id: I5b0066bc311b0ea995fa30bca1cd9235dc9b7d1b
Signed-off-by: Joel Kitching <kitching@google.com>
Reviewed-on: https://review.coreboot.org/28406
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Function pci_ehci_dbg_set_port() used NDA register DEBUGPORT_MISC_CONTROL,
which was deprecated in favor of a public PCI register (though only the
bits to enable debug port became public) 0x90. Therefore code needs to be
updated.
BUG=b:69231009
TEST=Build and boot grunt.
Change-Id: Ibb25992729d984b8570712f91a03a7cd1e9b8643
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/28344
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Most FADT report using ACPIv3 FADT table. Using the get revision
function keeps the table versions in sync.
Change-Id: Ie554faf1be65c7034dd0836f0029cdc79eae1aed
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/28277
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
There's a small window of opportunity when CPU is already in SMM but has
not yet entered S3 for a wake event to happen, which would cause a failed
S3 entry. Check for pending events at the very last moment possible, and
if there are pending wake events report them.
BUG=b:111100312
TEST=build and boot grunt.
Change-Id: I9472fdf481897fcf9f4c669f6b1514ef479fce7a
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/28247
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Since we can derive chromeos_acpi's location from that of
ACPI GNVS, remove chromeos_acpi entry from cbtable and
instead use acpi_gnvs + GVNS_CHROMEOS_ACPI_OFFSET.
BUG=b:112288216
TEST=None
CQ-DEPEND=CL:1179725
Change-Id: I74d8a9965a0ed7874ff03884e7a921fd725eace9
Signed-off-by: Joel Kitching <kitching@google.com>
Reviewed-on: https://review.coreboot.org/28190
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Since we can retrieve the address of ACPI GNVS directly
from CBMEM_ID_ACPI_GNVS, there is no need to store and
update a pointer separately.
TEST=Compile and run on Eve
Signed-off-by: Joel Kitching <kitching@google.com>
Change-Id: I59f3d0547a4a724e66617c791ad82c9f504cadea
Reviewed-on: https://review.coreboot.org/28189
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
In preparation to removing AmdLib, replace function LibAmdLocateImage()
with its ported version find_image().
BUG=b:112625809
TEST=Build and boot grunt.
Change-Id: I75ddd55f7e3e7f2cd7914f97c99b62690ae70660
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/28164
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
In preparation to removing AmdLib, function LibAmdLocateImage() has to be
ported to be used by agesawrapper. The most important aspect of this porting
is that it has to obey coreboot format, specifically 8 character tab and 80
characters max. This required breaking the function in 2 (to solve
indentation) and rename some variables to shorter names.
One important aspect was breaking
(AMD_MODULE_HEADER*)(((AMD_IMAGE_HEADER *) CurrentPtr)->ModuleInfoOffset)
into:
image_ptr = (AMD_IMAGE_HEADER *) current_ptr;
if (validate_image((void *)image_ptr->ModuleInfoOffset,
and, within validate_image completed by:
AMD_MODULE_HEADER *mod_ptr = (AMD_MODULE_HEADER *)module_chain;
BUG=b:112625809
TEST=Build grunt, functionality tested in next commit.
Change-Id: I0d1e8b966cf7606fdb15a95de5771f835f07b2bc
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/28144
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Fix the IASL build warnings:
Object is not referenced (Name [CDW2] is within a method [_OSC])
Object is not referenced (Name [CDW3] is within a method [_OSC])
Remove the not referenced objects. They are not needed.
BUG=b:112476331
TEST=IASL doesn't give the warning.
Change-Id: I5b38d4de3f9875c5b013a49eb5146bf5916b96a6
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/28121
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Print the PMxC0 S5/Reset status bits to the console.
TEST=Inspect console for Grunt
BUG=b:110788201
Change-Id: Ia905bb325a535fd4aa7082011cdfe92f08dff2cb
Signed-off-by: Edward Hill <ecgh@chromium.org>
Reviewed-on: https://review.coreboot.org/28020
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Remove VENDORCODE_FULL_SUPPORT from /soc/amd/stoneyridge/Kconfig and
from vendorcode/amd/pi/00670F00/Makefile.inc, thus completing the removal
of VENDORCODE_FULL_SUPPORT from coreboot.
BUG=b:112578491
TEST=none, VENDORCODE_FULL_SUPPORT already not used.
Change-Id: Idb5f6dc7add1617f7a97a97ae110901b2dec0996
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/28092
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Add a method in bootblock that can be used for printing registers.
BUG=none
TEST=compiled grunt
Change-Id: I8dff30e589761fbad92cfc2709546dba169993d8
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Reviewed-on: https://review.coreboot.org/28059
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
By setting this register in bootblock AmdInitEnv will no longer trigger
a reset in romstage. This fixes a few vboot test failures and also
speeds up boot time.
BUG=b:111610455
TEST=Built grunt and made sure bootblock only happens once on cold boot,
and S3 resume.
Change-Id: Ie19f7a14deaef45ac63156bec6946273c1b9447e
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Reviewed-on: https://review.coreboot.org/27876
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Add a function to provide a rudimentary dump of the Machine Check
Architecture registers. These values survive a warm reset.
BUG=b:65445599
TEST=Verify on a Grunt having propensity for #MC errors
Change-Id: Ib6875cabe3041e65c811d8b2232f7ac6bedd1a02
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/27926
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Extend the existing reset handling features in Stoney Ridge to plan for,
and recognize, warm resets. The ColdRstDet bit is always zero on a cold
reset, and is intended as a mechanism for the BIOS to determine the type
of a reset that occurred.
Set ColdRstDet=1 after all cores have been initialized, so that any
subsequent reset may be identified as warm/cold. A later patch will check
the value during mp_init.
Change-Id: I90255918de03018c9f090bff1e56a8bda5e7365e
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/27924
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Use the value discovered in the MCG_CAP[Count] for the number of MCA
status registers to clear. The generations should have the following
number of banks:
* Family 10h: 6 banks
* Family 12h: 6
* Family 14h: 6
* Family 15h: 7
* Family 16h: 6
Change-Id: I0fc6d127a200b10fd484e051d84353cc61b27a41
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/27923
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Change the defined name of MCI_STATUS (i.e. MCi_STATUS) to reflect its
MC0_STATUS address.
Change-Id: I97d2631a186965bb8b18f544ed9648b3a71f5fb0
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/27922
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
In procedure generate_cpu_entries(), the code was copied from code that
could change variables "plen" and "pcontrol_blk" based on number of cores.
This is not the case with stoneyridge (2 cores only), and there's no need
to use the variables. Remove them and replace with fixed values.
BUG=b:112253891
TEST=Build and boot grunt.
Change-Id: I0258b19960b050e8da9d218ded3f1f3bfccad163
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/27877
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
AMD ALIB Function 1 accepts the AC/DC startup state. This
is reported to be required for AMD PSPP settings.
BUG=b:112020107
TEST= build test
Change-Id: Ibb6c872d84745217912956c15d6ca2e8ba387561
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/27785
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Now that an updated bootloader with important fixes is available at coreboot
repository, all stoneyridge boards should use it. Move the selection of
SOC_AMD_PSP_SELECTABLE_SMU_FW from mb/google/kahlee to soc/amd/stoneyridge.
BUG=b:111428800
TEST=Build and boot grunt.
Change-Id: Idf8e348efbc85569aa1163125f412c5242c46eb4
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/27844
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
setup_spread_spectrum is called in early_init, meaning the console is
not initialized yet. So you won't see boot block booting twice.
BUG=b:111610455
TEST=booted grunt and verified that AmdInitReset does not reboot. I had
AGESA patched to skip the JTAG check.
Change-Id: Ia036ea513ac67d4b8bcf5a78029d969a4ae012a6
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Reviewed-on: https://review.coreboot.org/27813
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Grunt boards don't use SATA, so it should be disabled to save power.
Check if SATA is enabled in devicetree, and enable/disable the device
based on that setting.
BUG=b:112139043
TEST=Buil and boot grunt, checked the absence of SATA PCI.
Change-Id: I4a3b5f65e612e8da5bedff0c557a0850f350dfa8
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/27845
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
For some reason the PSPP setting was being overwritten in the common
code. Remove the setting and allow the oem customize function to
make the setting.
BUG=b:112020107
TEST= build test
Change-Id: If7f4511a71f725fedd60d33552656850e50d955d
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/27783
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
2 bits of LPC host control were originally not public, and wrongly
identified as IMC related. Now that the bits are available in public BKDG,
fix the naming of the bits.
BUG=b:111912080
TEST=build and boot grunt.
Change-Id: I1921f46c6be54eda6329c98267cec27004caadd5
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/27744
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Per AMD, the Integrated Micro Controller is not a supported feature of
the Stoney Ridge APU. Systems are expected to implement an external EC
for desired features. Remove all stoney IMC files and functions from
src/soc/amd/stoneyridge.
There are 2 "IMC bits" left (and used) that are not truly IMC. New BKDG
describe these bits, so a new patch will be released later to fix the
names and comment.
BUG=b:111780177
TEST=Build grunt and gardenia
Change-Id: I6a24e4c3f03d04713a030b884c611d9c64c4cb3a
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/27651
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The careena board needs different video settings to pass eye diagram test,
which does not affect negatively the grunt board. In preparation for new
VBIOS, create code that allows changing eDP training parameter.
BUG=b:111673328
TEST=Tested in child patch.
Change-Id: Ic0452618bfc5e05b9ef8280bb8ba398ec7b4ce95
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/27625
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Add internal graphics device 00.01.00 to the ACPI tables so that the
ACPI PCI option ROM save functions have a proper scope to save the
ROM to.
BUG=b:111697181
TEST=Check coreboot log doesn't have "PCI: 00:01.0: Missing ACPI scope"
and check _ROM method is added in the SSDT1.
Change-Id: I2c9ef8d9dff76805b1fcde2ccceef958a5b53b4f
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/27653
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
Put the PCIe clock pins in power-saving mode for the WiFi module to save
power.
Note: This currently does not appear to have any effect on grunt.
BUG=b:110041917
BRANCH=none
TEST=boot without this patch:
$ iotools mem_read32 0xfed80e00
0x0046f3ff
With this patch:
$ iotools mem_read32 0xfed80e00
0x0046f3f1
Change-Id: I389815bc36b8610a30b0cbb9d73262ad392e0181
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-on: https://review.coreboot.org/27465
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
update external processor name to match declaration in SSDT.
in SSDT:
Processor (\_PR.P000, 0x00, 0x00000410, 0x06) {}
Processor (\_PR.P001, 0x01, 0x00000000, 0x00) {}
in DSDT:
External (_PR_.CP00, UnknownObj)
External (_PR_.CP01, UnknownObj)
After fix this, ACPI _PSL (Passive List) now can return correct list
of processor objects for thermal passive cooling.
BUG=b:111478152
BRANCH=master
TEST=emerge-grunt coreboot
Change-Id: I78c838608c78eb7b5e3f8d5c67589e082c756201
Signed-off-by: Kevin Chiu <Kevin.Chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/27495
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
GPIO functions are required by the Grunt SMI handler.
Change-Id: Id729139b02c10bdd922b3df298f8f9feb1aff745
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/27485
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
The gpio_set function was not writing the correct GPIO register
address.
Change-Id: Ib306773ac72505977b606836bbaf3e2067324894
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/27484
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Change-Id: I21680354f33916b7b4d913f51a842b5d6c2ecef3
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/27408
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
It can not emit byte data without BytePrefix.
design to:
Or (Local5, GPIO_PIN_OUT, Local5)
error due to GPIO_PIN_OUT is 0x40 but 0x40 encoding means
nothing in AML spec.
so it will include next emitted string in Or:
Or (Local5, Local5, \_SB.GPW2)
fix:
Store (0x40, Local0)
Or (Local5, Local0, Local5)
BUG=b:110962003
BRANCH=master
TEST=emerge-grunt coreboot
extract SSDT then check ACPI syntax is correct
Change-Id: I7a0704112b77105826de87b14a38ed2f665224d5
Signed-off-by: Kevin Chiu <Kevin.Chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/27306
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Legacy IO enables access to RTC IO 0x70-0x73. This is needed for CMOS to
function correctly.
BUG=b:110817463
TEST=ran firmware_CorruptFwSigB on grunt
Change-Id: I533226ba764f567e348577d7fcf6ebe43336609a
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Reviewed-on: https://review.coreboot.org/27268
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
If IO CF9 is not enabled, hard_reset() won't do anything in bootblock or
verstage.
BUG=b:110817463
TEST=built on grunt and made sure that hard_reset() reboots.
Change-Id: I5f091077a17db3dfe5b8e8367163312db6828360
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Reviewed-on: https://review.coreboot.org/27267
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Old return value was not used, and function body
has die() in case of errors in allocation.
Change-Id: I89b0e9c927d395ac6d27201e0b3a8658e9585187
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/27261
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Garrett Kirkendall <garrett.kirkendall@amd.corp-partner.google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
When AllocationMethod == ByHost, buffer has to be
provided by caller.
Improve code symmetry, the named parameter is now
always pointer to the struct.
Change-Id: I2085f7d5d63ef96f4bd9d5194af099634c402820
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/27112
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Garrett Kirkendall <garrett.kirkendall@amd.corp-partner.google.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
The stoneyridge bootblock no longer makes AGESA calls. Remove the
support files from the bootblock build.
TEST=boot Grunt
Change-Id: I14d2336d5fb766a1acf5e812337ae0ab3ca4a6c1
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/27255
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Remove residual code that allowed successful building of the heapmanager
code. Now that stoneyridge no longer makes AGESA calls in bootblock, it
is safe to elimate the workaround.
BUG=b:74518368
TEST=boot Grunt
Change-Id: Ie169a691a177bcd8283c31c8188ce28bcbce82af
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/27254
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Limit is the maximum number of bits to be tested, however it's being checked
against the number of bytes of uint32_t. when it should be number of bits.
Create a macro to provide the number of bits, and use it instead of sizeof.
BUG=b:75996437
TEST=Add debug messages to see code passing beyond the check, build and
boot grunt, check that it passed the limit check, remove debug code.
Change-Id: Id1dfda26d789183b346b20c37fec923d996b80db
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/27162
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Put the PCIe clock pins in power-saving mode for the BayHub eMMC bridge to
save power. This requires use of an additional register (Misc control
register 2) and another bit in the existing 'protect' register. The naming
of bit 0 of that register is incorrect, based on the latest datasheet
(14 June 2018) so fix that too.
BUG=b:73726008
BRANCH=none
TEST=boot without this patch:
iotools mem_read32 0xfed80e00
0x0046ffff
With this patch:
$ iotools mem_read32 0xfed80e00
0x00463fff
Also see that the PCIe clock stops when eMMC is idle and can be started by
starting disk activity.
Change-Id: I5ad1467b2e2e151215d2dfd2ce48cd4a451fe480
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-on: https://review.coreboot.org/26515
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
PM registers used for generating SWS values are being stored in a static
variable within southbridge.c. In order to have it available for any source
involved in building the platform, move the storage to cbmem, using id
CBMEM_ID_POWER_STATE. Also add a variable that informs from which state
the system is waking from, extracted from register ACPI_PM1_CNT_BLK. This
variable will later be useful in detecting failed S3 resume.
BUG=b:80119811
TEST=Add code to print SWS parameters and state it's waking from. Build
and boot grunt, suspend and resume, check output for valid values. Remove
the print code.
Change-Id: Ib27a743b7e7f8c94918caf7ba5efd473f4054986
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/27109
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The entire StdHeader field is really supposed to
be forked from a template for each entry into the
AGESA API. Current code assumes only Callout would
be relevant, which is not quite the case.
Change-Id: I0cc66d01d62fa8dc6bb7c9f9fab6fa4753827554
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/27111
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Garrett Kirkendall <garrett.kirkendall@amd.corp-partner.google.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
Change-Id: I630d49ab504d9f6e052806b516a600fa41b9a8da
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/26991
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
GSMI Set Event Log is taking more than 1K in stack. This causes the
stack to overflow into the adjacent stack. This has the side effect of
causing any CPU waiting for the SMI handler to complete to crash when
the lock is unlocked because the return pointer has been smashed.
BUG=b:80539294
TEST=built on grunt and tested by running `halt` from the OS.
Change-Id: Ib170c7d03909ef3d20831726b285178a75007b06
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Reviewed-on: https://review.coreboot.org/27033
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
With platforms moved to RELOCATABLE_RAMSTAGE, these
overrides no longer have a meaning.
Overrides existed because AGESA ramstage did not fit within
the default 1 MiB of RAMTOP - RAMBASE, when placed low.
Change-Id: I0185875dc550de74877c94f36128d5979e5553d6
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/26813
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I4571e8b560559b3d7afe429eca8caa1512e244a8
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/26811
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Enable the two ranges to be used for the new callouts, AgesaHeapRebase
and AgesaGetHeapBaseInDram.
TEST=Boot grunt w/experimental blob, try different addresses
BUG=b:74518368
Change-Id: Ic7716794dc7d75f849e6e062865d6efbeb4292df
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/26147
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Implement an optional callout for AgesaHeapRebase which allows AGESA
to override any internal hardcoded heap addresses.
Designate a region in CAR that may be used for pre-mem heap and return
that address before DRAM is configured. After DRAM is up, the address
in cbmem is returned.
TEST=Boot grunt with patchstack and experimental blob
BUG=b:74518368
Change-Id: Ieda202a6064302b21707bd7ddfabc132cd85ed45
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/25458
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Implement a new AGESA callout that may be used to find the correct
temporary location in DRAM to store heap data.
Near the end of AmdInitPost, AGESA migrates its heap from a CAR-based
location to a temporary region. Once cbmem has been established, the
heap will be relocated again in AmdInitEnv from the temp location to
the final one.
This patch does not materially affect the behavior of AGESA's heap
management. It only puts coreboot in control of the location. Future
work may refactor the copying.
TEST=Boot grunt with patchstack and experimental blob
BUG=b:74518368
Change-Id: Ibc5cc988e3e80d78f50cf0195e952b657141e570
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/26146
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
There are some acpigen functionality that have not been implemented. They
are defined as week within acpigen.c, in order to not break the build.
This adds stoneyridge specific versions.
BUG=b:79546790
TEST=Build grunt with added debug code to gpio_lib.asl. Boot to OS,
activate ACPI debug, activate S3 stress test. Interrupt stress test, do a
"cat /var/log/messages" saving the serial output. Examine the serial
output, see added debug code showing action taken. Confirm action by
reading proper register. Debug code removed.
Change-Id: I9062d889f828a3175b89e6f4a3659ebbf90eac68
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/26335
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
PM1 and GPE0 are being stored directly to NVS, when actually what should
be saved is the index of the bit responsible for waking. Fix the procedures
and add definitions to the actual IO addresses to be read when recording
status and enable registers.
BUG=b:75996437
TEST=Build and boot grunt. Once in OS, execute a sleep and a wake. See the
message indicating which indexes are being save in NVS for _SWS. Try sleep
stress test, verify that the index is different from that of power button.
Change-Id: I8bafc7bb7dd66e7f0eb8499e748535bbdcac5f53
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/26547
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
There are some acpigen functionality that have not been implemented. In
order to implement them, ACPI GPIO functions to read and write to the
control MMIO of a particular pin is needed. So as a preliminary task to
implementing acpigen functions, create a library with functions to be
accessed by acpigen generated ACPI code.
BUG=b:79546790
TEST=Build grunt, more tests with commit 0f2acbd6b1.
Change-Id: I21c014b7f2698dd9193dae3113b18ee2a7303bcf
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/26334
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
This is Garrett's patch with a bit of cleanup.
BUG=b:65442212
TEST=Was able to boot, suspend and resume on grunt.
Change-Id: I55959b59a4e60b679d959ebd77de27e5d454f5f7
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Reviewed-on: https://review.coreboot.org/26478
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
By default we use a 1:1 mapping between GEVENT bits and the corresponding
SCI_MAP entry. However, we still must program the SCI_MAP entries
with the GEVENT number.
BUG=b:109759838
TEST=(1) powerd_dbus_suspend
(2) move finger on touchpad for ~1 second
=> system resumes from S3
Change-Id: Ie7be45264f9bfec56efc47a03071fdb924d16b6a
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/26930
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
No need to provide an option to try disable this.
Also remove explicit ´select RELOCATABLE_MODULES'
lines from platform Kconfigs.
Change-Id: I5fb169f90331ce37b4113378405323ec856d6fee
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/26815
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Change-Id: Ia024fb418f02d90c38b9a35ff819c607b9ac4965
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/26651
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Change-Id: Iee816628ac3c33633f5f45798562a4ce49493a65
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/26580
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Add the ACPI devices defined in ASL to the soc_acpi_name() lookup
function.
BUG=b:80280671
TEST=Add ACPI method to specific GPP bridge. Boot and verify method
with ACPI dump.
Change-Id: I5117e0d39db831364173c9c61ccdab6e34f18c59
Signed-off-by: Marc Jones <marc.jones@scarletltd.com>
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/26698
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Kevin Chiu <Kevin.Chiu@quantatw.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
Boards could choose a high ROM_SIZE that would result in an MTRR config
that conflicts with other resources. Thus, always use the filtered
CACHE_ROM_SIZE.
Change-Id: I66d36b84ce49c1cb98cb36a4731977baaedf3225
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/26575
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change adds and updates headers in all of the soc files that
had missing or unrecognized headers. After this goes in, we can
turn on lint checking for headers in all soc directories.
Change-Id: I8b34dcd10c692f1048bd8d6c0fe3bfce13d54967
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/26569
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
This won't actually get called yet since the GPIO pin has not been
configured as SMI.
BUG=b:80295434
TEST=grunt: Made sure events could be processed.
Change-Id: I189e26196e4543b3e34bff5d9df8566eff07d585
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Reviewed-on: https://review.coreboot.org/26546
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
This copies what Intel does.
BUG=b:80295434
TEST=grunt: Made sure that the S5 SMI interrupt gets fired.
Change-Id: I7874824cad01054c6bdeff12d248e671f27be030
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Reviewed-on: https://review.coreboot.org/26545
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
The default interrupt control for GPIO pins within stoneyridge is for
edge triggered, high. However, sometimes these need to change, or maybe
the interrupt needs to be reported or delivered. This was the case of
platform grunt, where the interrupt related bits were being changed
afterwards. Ideally all the bits should be programmed through the same
procedure. Create several PAD_INT definitions (for general configuration,
for trigger configuration and for interrupt type configuration) and change
function sb_program_gpios() to accept the output from PAD_INT_XX and
program all the necessary bits while keeping compatibility with other
PAD_XX definitions.
BUG=b:72875858
TEST=Add code to report GPIO and interrupt configuration, build grunt and
record a baseline. Add new code, rebuild grunt and record a test output.
Compare baseline against test, there should be no change in GPIO or
interrupt programming.
Remove code that reports GPIO/interrupt configuration.
Change-Id: I3457543bdf64ec757fd82df53c83fdc1d03c1f22
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/25758
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Increment the boot_count from romstage when not resuming from S3.
BUG=b:80266624
TEST=firmware_EventLog
TEST=boot, then:
mosys eventlog list | grep boot
1 | 2018-05-24 16:51:42 | System boot | 1
reboot
mosys eventlog list | grep boot
1 | 2018-05-24 16:51:42 | System boot | 1
6 | 2018-05-24 16:52:34 | System boot | 2
Change-Id: Ideec9da809e494fb0ea073f648540285972f8238
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-on: https://review.coreboot.org/26525
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
We are already reporting the Wake source, but we must also report the
ACPI wake itself.
BUG=b:79865267
TEST=firmware_EventLog
Change-Id: Id26dff46379800a63ab9b77f135d23c6382f77e6
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-on: https://review.coreboot.org/26522
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
_SWS is the recommended method of wake source retrieval. Now that PM1I and
GPEI are available at NVS, add the method _SWS to kahlee/grunt ACPI code.
BUG=b:76020953
TEST=Build grunt
Change-Id: I5930438af40e6f9177462582cafb65401d9c60f4
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/26217
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
ACPI _SWS needs information on PM1 and ACPI events (though events can be
read directly). Unfortunately PM1 is cleared in normal path and in resume
path. Save PM1 and ACPI events in NVS to be accessed by ACPI _SWS.
BUG=b:75996437
TEST=Build and boot grunt recording serial. Run suspend stress test, after
3 resumes closed file and examined for the message indicating what was
being saved to NVS. Two different path, normal boot (first boot) and
resume path had different PM1.
Change-Id: If3b191854afb27779b47c3d8d9f5671a255f51b5
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/26208
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Use of device_t has been abandoned in ramstage.
Change-Id: I82089475eb43d58303d1091f35aee06f1f04b4a4
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/26459
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
|
|
Use of device_t has been abandoned in ramstage.
Change-Id: I84fbc90b2a81fe5476d659716f0d6e4f0d7e1de2
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/26458
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
|
