Age | Commit message (Collapse) | Author |
|
Since coreboot is written in C and not C++, having the double
underscores as a prefix is not an issue, but it also doesn't add much
information, so drop them and the trailing ones as well.
Change-Id: I1028fb9097efab8ffae5ffa9fe85a97feebc78a9
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47583
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
TEST=Timeless build doesn't change for Mandolin and Gardenia.
Change-Id: I5d3ae1459c333658f4c86388f1822d92ca13c658
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47514
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jeremy Soller <jeremy@system76.com>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Jason Glenesk <jason.glenesk@gmail.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
eSPI interrupts are active level high. The eSPI polarity register
in the chipset inverts incoming signals if the corresonding bit
is 0 in the register. Therefore, all active high (edge or level)
virtual wire interrupts need to ensure they are not inverted.
And really the sender of the interrupts should be conforming to the
the eSPI spec. As such inverting any signals should not be necessary,
but this register in the chipset allows for fixing up those misbehaviors.
BUG=b:157984427
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Change-Id: I7346bb0484506d96d7ab2e6d046ffa0571683a48
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43010
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This change adds a helper function espi_setup() which allows SoCs to
configure connection to slave. Most of the configuration is dependent
upon mainboard settings in espi_config done as part of the device
tree. The general flow for setup involves the following steps:
1. Set initial configuration (lowest operating frequency and single mode).
2. Perform in-band reset and set initial configuration since the
settings would be lost by the reset.
3. Read slave capabilities.
4. Set slave configuration based on mainboard settings.
5. Perform eSPI host controller configuration to match the slave
configuration and set polarities for VW interrupts.
6. Perform VW channel setup and deassert PLTRST#.
7. Perform peripheral channel setup.
8. Perform OOB channel setup.
9. Perform flash channel setup.
10. Enable subtractive decoding if requested by mainboard.
BUG=b:153675913
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: I872ec09cd92e9bb53f22e38d2773f3491355279e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41272
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
CB:41194 got rid of "this file is part of" lines. However, there are
some changes that landed right around the same time including those
lines. This change uses the following command to drop the lines from
new files:
sed -i -e '/file is part of /d' $(git grep "file is part of " |egrep ":( */\*.*\*/\$|#|;#|-- | *\* )" | cut -d: -f1 |grep -v crossgcc |grep -v gcov | grep -v /elf.h |grep -v nvramtool)
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: Ic3c1d717416f6b7e946f84748e2b260552c06a1b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41342
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change provides a helper function espi_update_static_bar() that
informs the eSPI common driver about the static BAR to use for eSPI
controller instead of reading the SPIBASE. This is required to support
the case of verstage running on PSP.
BUG=b:153675913
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: I1f11bb2e29ea0acd71ba6984e42573cfe914e5d7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41256
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
This change adds the following helper functions for eSPI decode:
1. espi_open_io_window() - Open generic IO window decoded by eSPI
2. espi_open_mmio_window() - Open generic MMIO window decoded by eSPI
3. espi_configure_decodes() - Configures standard and generic I/O
windows using the espi configuration provided by mainboard in device tree.
BUG=b:153675913,b:154445472
Change-Id: Idb49ef0477280eb46ecad65131d4cd7357618941
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41073
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change adds eSPI register definitions for I/O and MMIO decode
using eSPI on AMD SoCs. Additionally, it also adds a macro to define
the offset of ESPI MMIO base from SPI MMIO base.
BUG=b:153675913
Change-Id: Ifb70ae0c63cc823334a1d851faf4dda6d1c1fc1a
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41072
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|